Gas Electro-Mechanical Valves

Transcription

1 Gas Electro-Mechanical Valves TEHNIAL ATALOG Electrically actuated valves with powerful closing spring provide closure in less than second for reliable, long-life operation Factory Mutual, A, UL and E approved; anadian registration obtained on all valve bodies Hazardous Locations valves approved for Nonincendive lass I, Division areas Full assessment to IE 6508 as IL 3 capable Visual position indication provided ast iron, carbon steel, low temperature carbon steel and stainless steel body assemblies with internal trim options to handle general purpose or corrosive gases; oxygen compatibility available Ambient and gas temperature ranges of -9 to 60 Application flexibility provided with 3/4 (DN0) through 6 (DN50) line sizes & line pressures up to 8.6 bar (86 kpa) Unique bonnet design eliminates packing adjustments, reducing maintenance and minimizing drag on closing MAXON electro-mechanical gas valves meet Fluid ontrol Institute (FI) 70- control valve standard for lass VI seat leakage Field rotatable top assemblies in 90 increments to fit specific application requirements Actuator assemblies available with manual reset or automatic reset operators Normally-closed and normally-open versions available Overtravel position switches for open and closed position 3M

2 GA ELETRO-MEHANIAL VALVE OPERATING ONEPT Automatic reset valves Model designation and Models MA, MA, MA, MA H Models HMA Manual reset valves Model designation (former model designation) and Models only MM, MM, MM All valves are designed to return to normal position instantly with any interruption in the electric power supplied through your safety circuit. (Motorized) automatic reset actuators are used where remote access or unmanned applications are needed. Manual reset actuators require operating personnel to be physically present to actuate the valve from its at rest position. witch assemblies Provides positive valve position - open or closed omplies with proof of closure requirements Easily integrates with an analog control system, D or PL IP 67 sealed switches included for Non-incendive valves 3M E - m - 4/6

3 GA ELETRO-MEHANIAL VALVE Body and trim selections ast iron, carbon steel, low temperature carbon steel and stainless steel body assemblies feature metal-to-metal seating that meets FI 70- control valve standard for lass VI seat leakage. Internal trim options are available for general purpose and corrosive gases. Oxygen compatible trims are also available. Valve body assemblies are offered in normally-closed shut-off and normally-open vent versions. Valve bodies are available in threaded, flanged, and socket-welded connections. Bodies are currently available in DN0 through DN50 (3/4 through 6 ) sizes. Body design utilizes a straight-through flow path, which minimizes the pressure drop through the body. Normally-closed shut-off valves utilize power to open. Removal of electrical signal allows instantaneous release of the holding mechanism, allowing the powerful closing spring to close the valve in less than one second. eries MA, MM, MA, MM, MA, MM, MA, MM, HMA Normally-open vent valves utilize power to close. Removal of electrical signal allows instantaneous release of the holding mechanism, allowing the valve to open in less than one second. eries MA, MM, MA, MM, MA, MA, MM E - m - 4/6 3 3M

4 GA ELETRO-MEHANIAL VALVE Agency approvals and certifications General Purpose Valves Non-incendive/Non-sparking Valves MA, MM, MA, MA, MM, MA, MA, MM, MA, MM, MA, MM, MM, MM MA, HMA tandards Markings tandards Markings FM approvals FM 7400 FM approvals - IE Ex ertification Not applicable FM 7400 FM 36 FM 3600 FM 380 IE IE (Normally open valves) UL approvals UL 49 Not applicable Not applicable A International A 6.5 European approvals [] EN 6 EN 3774 Listed General Purpose 68A Listed afety hut-offf 68A (Normally open valves) /I L/KL: A, GR E PIN: 87BQ83 A 6.5 A. No. 3 Not applicable lass I, Div., Groups ABD lass II, Div., Groups FG lass III, Div. Temp ode T4 (A) T3 (D, sizes 3/4 - -/ ) T3 (D, sizes -6 ) Ex na n II T4A (A), T3 (D), Ta=60 Gc Ex tc III T35 Dc IP65 FMG.003X lass I, Div., Groups ABD lass II, Div., Groups FG lass III, Div. Temp ode T4 (A) T3 (D) Not applicable IE approvals IE 6508 None IE 6508 None KTL approvals None None Not applicable MA: -KB4BO-0057 MM: 3-KB4BO-049 MA: 6-KA4BO-007 MM: 6-K4BO-008 AGA ertifications A 469 None (LA ) A 469 None [] Product certified to meet the following (MA, MA, MM, MM, MA,MA, MM only): Gas Appliance Directive (009/4/E) Low Voltage Directive (04/35/EU) EM Directive (04/30/EU) Pressure Equipment Directive (04/68/EU) up to DN00 /I Valve cycle requirements This is based on the standards that MAXON valves are approved to and the corresponding minimum number of cycles to be completed without failure as shown in the chart below. UL (UL 49) A (A 6.5) FM (FM 7400) European (EN6) Automatic eries MA, MA Manual eries MM, MM Vent valves eries MA, MA, MM, MM 00,000 00,000 0,000 6,000 0,000 0,000 6,000 No special requirements No special requirements <= DN5 00,000 <= DN80 00,000 <= DN50 50,000 No special requirements No special requirements 3M E - m - 4/6

5 GA ELETRO-MEHANIAL VALVE VALVE MODEL NUMBER DERIPTION Every MAXON gas electro-mechanical valve can be accurately identified by the model number shown on the valve nameplate. The example below shows a typical gas electro-mechanical valve model number, along with the available choices for each item represented in the model number. onfigured item number Valve body Actuator Valve size Flow capacity Valve type Normal position Area classification Body connection Body seals & bumper material Body material Internal trim package olenoid OR circuit board voltage Motor voltage OR handle side plate Motor timing (automatic valves only) 300 MA - A A - B B 0 A 0 witch options Enclosure rating Instruction language Valve size 075-3/4 (DN0) 00 - (DN5) 5 - -/4 (DN3) / (DN40) 00 - (DN50) / (DN65) (DN80) (DN00) (DN50) Flow capacity - tandard - P body construction H - High capacity Valve reset type MA - MAXON automatic (motorized) valve MM - MAXON manual valve Normal position - Normally closed shut-off valve - Normally open vent valve Area classification - General purpose - Non-incendive, lass I, II and III Division 4 - Valve body only (400 & 600 high capacity valves only) Body connection A - ANI (NPT) threaded B - ANI flanged (PN0) - IO 7/ threaded D - DIN PN6 flanged E - ocket welded nipple F - ocket welded nipple w/lass 50 flange (IO 7005 PN0) H - EN09- PN6 flanged (IO PN6) Body seals & bumper material A - Buna o-rings/buna bumper B - Viton o-rings/buna bumper - Viton o-rings/viton bumper [] D - Ethylene Propylene o-rings/ Ethylene Propylene bumper [] E - Omniflex o-rings/buna bumper F - Omniflex o-rings/viton bumper [] Body material - ast iron - arbon steel 5 - tainless steel 6 - Low temp carbon steel Internal trim package - Trim package - Trim package 4 - Trim package, oxy clean [] olenoid OR circuit board voltage A - 5VA 50 Hz B - 5VA 60 Hz - 30VA 50 Hz D - 30VA 60 Hz E - 08VA 50 Hz F - 4VD G - 0VD Motor voltage A - 5VA 50 Hz B - 5VA 60 Hz - 30VA 50 Hz D - 30VA 60 Hz E - 4VD Motor timing -.5 second - 6 second 3 - second * - N/A with manual valves Automatic valves 0 - VO/none - VO/V - VO/V 3 - VO/V 4 - VOH/ VH OR witch options Handle side plate A - tandard handle B - Tandem main - Tandem blocking D - Tandem overhead E - Wheel and chain Manual valves 0 - None - VO/V - VO/V 3 - VO/V [] -8 minimum ambient temperature limit Enclosure rating A - NEMA 4 B - NEMA 4X Instruction language 0 - English E - m - 4/6 5 3M

6 GA ELETRO-MEHANIAL VALVE VALVE MODEL RO REFERENE MAXON valve model numbers have changed to intelligent coded model numbers for easy identification and specification. Valves manufactured prior to October, 008 will contain an older model number system which can be easily cross referenced with the chart below. Normally-closed (shut-off) valves General purpose, NEMA 4 or 4X Model number (prior to October, 008) P P 7000 Normally-open (vent) valves General purpose, NEMA 4 or 4X Model number (prior to October, 008) TO-M TO-A TO-A-P Normally-closed (shut-off) valves Hazardous area classification Model number (prior to October, 008) 808 NI 808 NI P 5000 NI 5000 NI P Normally-open (vent) valves Hazardous area classification Model number (prior to October, 008) TO-M-NI TO-M-NI-P TO-A-NI TO-A-NI-P New model designation MM MM MA MA HMA New model designation MM MA MA New model designation MM MM MA MA New model designation MM MM MA MA 3M E - m - 4/6

7 GA ELETRO-MEHANIAL VALVE VALVE BODY AEMBLY OPTION & PEIFIATION Nominal pipe size DN0 (3/4 ) DN5 ( ) DN3 (-/4 ) DN40 (-/ ) DN50 ( ) DN65 (-/ ) DN80 (3 ) DN00 (4 ) DN50 (6 ) Flow capacity Body connections Normally-closed shut-off valve - Body options Body material Trim package A,, cast iron,, 4 A,, E, F, 6, carbon steel 5, stainless steel, 4 A,, cast iron,, 4 A,, E, F, 6, carbon steel 5, stainless steel, 4 v/kv rating Flow at MOPD (m 3 h) MOPD rating (mbar/kpa) pecial service MOPD rating (mbar/kpa) [] 9/ / /06.8 0/ / /06.8 A,, cast iron,, 4 45/ / /06.8 A,, cast iron,, 4, 6, carbon steel 53/ / /37.9 A,, E, F, 4 5, stainless steel A, B,, D, H, cast iron,, 4, 6, carbon steel 86/ / /03.4 A,, E, F, 4 5, stainless steel, cast iron 7/ / /68.9 A, B,, D, cast iron,, 4, 6, carbon steel 304/ / /03.4 B, D, H, 4 5, stainless steel A,, cast iron 73/ / /34.5 A, B,, D, H, cast iron,, 4, 6, carbon steel 43/ / /68.9 B, D, H, 4 5, stainless steel, cast iron,, 4, 6, carbon steel 490/ / /68.9, 4 5, stainless steel B, D, H, cast iron,, 4 H, carbon steel 79/ / /68.9, 4 5, stainless steel, cast iron,, 4 Not, carbon steel 869/ /37.9, 4 available 5, stainless steel B, D, H, cast iron,, 4 7/ H, carbon steel / /68.9, , stainless steel [] pecial service fuels (see page ): Valve maximum operating pressure differential (MOPD) to be reduced Body connections: A - NPT B - ANI flanged (IO 7005 PN0) - IO 7- threaded D - DIN PN6 flanged E - ocket welded nipple F - ocket welded nipple w/lass 50 flange (IO 7005 PN0) H - EN09- PN6 (IO PN6) Body material: - ast iron - arbon steel 5 - tainless steel 6 - Low temp carbon steel Trim package options and typical material: series stainless steel seat, hardened ductile iron disc, PEEK follower ring - 36 seat, 36 disc, PEEK follower ring 4 - Oxy clean, trim Body seals and bumper: - Buna o-rings/buna bumper - Viton o-rings/buna bumper - Viton o-rings/viton bumper - Ethylene Propylene o-rings/ethylene Propylene bumper - Omniflex o-rings/buna bumper - Omniflex o-rings/viton bumper Refer to valve body assembly gas compatibility for proper elastomer selection. E - m - 4/6 7 3M

8 GA ELETRO-MEHANIAL VALVE Nominal pipe size DN0 (3/4 ) DN5 ( ) DN40 (-/ ) DN50 ( ) DN65 (-/ ) DN80 (3 ) DN00 (4 ) Flow capacity Body connections Normally-open vent valve - Body options Body material Trim package A,, cast iron,, 4 A,, E, F, 6, carbon steel 5, stainless steel, 4 A,, cast iron,, 4 A,, E, F, 6, carbon steel 5, stainless steel, 4 A,, cast iron,, 4 A,, E, F, 6, carbon steel 5, stainless steel, 4 A, B,, D, H, cast iron,, 4 A,, E, F, 6, carbon steel 5, stainless steel, 4 A, B,, D, cast iron,, 4 B, D, H, 6, carbon steel 5, stainless steel, 4 A, B,, D, H, cast iron,, 4 B, D, H, 6, carbon steel 5, stainless steel, 4, cast iron,, 4 B, D, H, 6, carbon steel 5, stainless steel, 4 v rating Flow at MOPD (m 3 h) MOPD rating (mbar/kpa) pecial service MOPD rating (mbar/kpa) [] 9/ / /06.8 0/ / / / / / / / / / / / / / / / / /68.9 [] pecial service fuels (see page ): Valve maximum operating pressure differential (MOPD) to be reduced Body connections: Body material: A - NPT - ast iron B - ANI flanged (IO 7005 PN0) - arbon steel - IO 7- threaded 5 - tainless steel D - DIN PN6 flanged 6 - Low temp carbon E - ocket welded nipple steel F - ocket welded nipple w/lass 50 flange (IO 7005 PN0) H - EN09- PN6 (IO PN6) Trim package options and typical material: series stainless steel seat, hardened ductile iron disc, PEEK follower ring - 36 seat, 36 disc, PEEK follower ring 4 - Oxy clean, trim Body seals and bumper: - Buna o-rings/buna bumper - Viton o-rings/buna bumper - Viton o-rings/viton bumper - Ethylene Propylene o-rings/ethylene Propylene bumper - Omniflex o-rings/buna bumper - Omniflex o-rings/viton bumper Refer to valve body assembly gas compatibility for proper elastomer selection. 3M E - m - 4/6

9 GA ELETRO-MEHANIAL VALVE VALVE ATUATOR OPTION Automatic reset valve - Actuator options Nominal pipe size DN0 (3/4 ) DN5 ( ) DN3 (-/4 ) -/ (DN40) DN50 ( ) DN65 (-/ ) DN80 (3 ) DN65 (-/ ) DN80 (3 ) DN00 (4 ) DN00 (4 ) DN50 (6 ) Flow capacity Normal position,,,,,,, Area classification olenoid OR circuit board voltage, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G Motor voltage A, B, D, E A, B,, D A, B,, D A, B,, D A, B,, D A, B,, D A, B,, D A, B,, D A, B,, D A, B,, D A, B,, D Motor timing,,,,,,,,,,,,,, witch options 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 0,,, 3, 4 0,,, 3 H A, B,, D, G A, B,, D 3 0,,, 3 H A, B,, D, G A, B,, D 3 0,,, 3 Flow capacity - tandard - P body construction H - High capacity Normal position - Normally-closed shut-off valve - Normally-open vent valve Area classification - General purpose - Non-incendive, lass I, II and III, Division olenoid OR circuit board voltage A - 5VA 50 Hz B - 5VA 60 Hz - 30VA 50 Hz D - 30VA 60 Hz E - 08VA 50 Hz F - 4VD G - 0VD Motor voltage A - 5VA 50 Hz B - 5VA 60 Hz - 30VA 50 Hz D - 30VA 60 Hz E - 4VD Motor timing -.5 second - 6 second 3 - second witch options 0 - VO/None - VO/V - VO/V 3 - VO/V 4 - VOH/VH E - m - 4/6 9 3M

10 GA ELETRO-MEHANIAL VALVE Manual reset valve - Actuator options Nominal pipe size DN0 (3/4 ) DN5 ( ) DN3 (-/4 ) DN40 (-/ ) DN50 ( ) DN65 (-/ ) DN65 (-/ ) DN80 (3 ) DN80 (3 ) DN00 (4 ) DN50 (6 ) Flow capacity Normal position Area classification olenoid voltage, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G, F, G Handle side plate options A, E A, E A, E A, E A, E A, E A, E A, E A, E A, E witch options 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 0,,, 3 A, E 0,,, 3, F, G 0,,, 3 0,,, 3 A, E 0,,, 3 A, B,, D 0,,, 3 0,,, 3 Flow capacity - tandard - P body construction H - High capacity Normal position - Normally-closed shut-off valve - Normally-open vent valve Area classification - General purpose - Non-incendive, lass I, II and III, Div olenoid voltage A - 5VA 50 Hz B - 5VA 60 Hz - 30VA 50 Hz D - 30VA 60 Hz E - 08VA 50 Hz F - 4VD G - 0VD Handle side plate options A - tandard handle B - Tandem main - Tandem blocking D - Tandem overhead E - Wheel and chain witch options 0 - None - VO/V - VO/V 3 - VO/V 3M E - m - 4/6

11 GA ELETRO-MEHANIAL VALVE VALVE BODY AEMBLY PEIFIATION ) Body ) Bonnet 3) eat 4) Disc 5) Follower ring 6) eat o-ring 7) Body o-ring 8) Wavy spring 9) tem 0) pring pin ) tem o-ring ) triker plate 3) Bumper 4) Flow direction 5) Typical stem/disc connection used with smaller sized valves 5 Threaded P body design shown 4 Item number Description Body ast iron Bonnet ATM A6, lass B Body and bonnet materials Material code 5 6 arbon steel ATM A6, Gr. WB tainless steel ATM A35 Gr. F8M Low temp carbon steel ATM A35 Gr. LB Body seals and bumper material Item number Description Material 6 eat o-ring Buna o-rings/buna bumper 7 Body o-ring tem o-ring 3 Bumper Viton o-rings/buna bumper Viton o-rings/viton bumper Ethylene Propylene o-rings/ethylene Propylene bumper Omniflex o-rings/buna bumper Omniflex o-rings/viton bumper Item number Description Trim package materials Internal trim package 3 eat 400 series stainless steel 36 stainless steel 4 Disc Hardened ductile iron 36 stainless steel 5 Follower ring PEEK PEEK 8 Wavy spring 300 series stainless steel 9 tem 7-4 PH stainless steel 0 pring pin (when required) arbon steel 400 series stainless steel triker plate 7-7 PH stainless steel E - m - 4/6 3M

12 GA ELETRO-MEHANIAL VALVE VALVE BODY AEMBLY - GA OMPATIBILITY Gas Gas code uggested material options Body seals & bumper Body & bonnet Trim option [7] MOPD rating Agency approvals and certifications E [4] FM A [3] GAD LVD PED Air AIR A, B,, E, F,, 5, 6, td. X X X X X Ammonia AMM A, D, E,, 5, 6, td. X X X X Butane gas BUT A, B,, E, F,, 5, 6, td. X X X X X X oke oven gas OKE, F,, 5, 6 [5] X X X X Delco DEL A, B,, E, F,, 5, 6, td. X X X X X Digester [] DIG Analysis required 5 [5] X X X X Endothermic AGA ENDO A, B,, E, F,, 5, 6, td. X X X X X Exothermic gas EXO A, B,, E, F,, 5, 6, td. X X X X X Hydrogen gas HYD A, B,, E, F,, 5, 6, [] X X X X Manufactured [] MFGD Analysis required 5 td. X X X X Natural gas NAT A, B,, E, F,, 5, 6, td. X X X X X X Nitrogen NIT A, B,, E, F,, 5, 6, td. X X X X X No. fuel oil [6] NOOIL A, B,, E, F,, 5, 6, td. X X X X X No. fuel oil [6] NOOIL A, B,, E, F,, 5, 6, td. X X X X X Oxygen (hi p) OXYH, D, F, 5, barg 86 kpag X X X X UL [3] Oxygen (lo p) OXYL, D, F,, 5, barg 07 kpag X X X X Propane PROP A, B,, E, F,, 5, 6, td. X X X X X X Refinery [] REF Analysis required 5 [5] X X X X our natural [] OUR Analysis required 5 [5] X X X X Town gas [] TOWN Analysis required 5 td. X X X X X Land fill gas [] LAND Analysis required 5 [5] X X X X [] Other body and trim packages may be acceptable pending fuel analysis. For pricing inquiries, Viton or Omniflex o-rings should be used. ontact MAXON for details. [] Valve maximum operating pressure differential (MOPD) to be reduced by 5% from standard ratings. [3] IO connections are not recognized by A or UL standards [4] MA, MA, MM, MM, MA, MA, MM eries electro-mechanical valves meet the essential requirements of the Low Voltage (04/35/EU), EM (04/30/EU), Gas Appliance - GAD (009/4/E), and Pressure Equipment (04/68/EU) Directives. The Gas Appliance Directive only covers the use of commercially available fuels (natural gas, butane, town gas and LPG). The Pressure Equipment Directive does not cover MAXON valves with ast Iron Bodies or sizes larger than DN00 (4 ). [5] pecial service fuels: Valve maximum operating pressure differential (MOPD) to be reduced from standard ratings [6] Trim Option is only allowed with body and bonnet Option. Body seals & bumper: A - Buna o-rings/buna bumper B - Viton o-rings/buna bumper - Viton o-rings/viton bumper D - Ethylene propylene o-rings/ethylene propylene bumper E - Omniflex o-rings/buna bumper F - Omniflex o-rings/viton bumper Body & bonnet: - ast iron - arbon steel 5 - tainless steel 6 - Low temp carbon steel Trim package: - Trim package - Trim package 4 - Trim package, oxy clean 3M E - m - 4/6

13 GA ELETRO-MEHANIAL VALVE ELETRIAL DATA General MAXON shut-off valves are electrically actuated from a power source. tandard assemblies include an internal holding solenoid or clutch and printed circuit board. Position switch wiring diagrams (reproduced below) are part of each valve assembly, summarizing electrical data and wiring for a valve equipped with terminal block and a full complement of optional switches. Good practice normally dictates that auxiliary switches in valves should be used for signal duty only, not to operate additional safety devices. Valve position switches are offered in PDT (single pole/ double throw). Recommended packages include one open switch and one closed switch (VO/V). Additional auxiliary switches are designated by VO/V. V (valve closed switch) is actuated at the end of the closing stroke. VO (valve open switch) is actuated at the end of the opening stroke. witch amperage ratings are shown on the schematic wiring diagrams below. DO NOT EXEED rated amperage or total load shown. Diagrams show valve with a full complement of switches. For normally-closed valves, the wiring diagram illustrates the switch contact positions with the valve closed. For normally-open valves, the wiring diagram illustrates the switch contact position with the valve open. Figure : Normally-closed shut-off valves NORMALLY LOED VALVE 06/ VO- VO- V- V- M and Model valves L(+) N(-) L N PDT PDT PDT PDT DPDT DPDT GENERAL PURPOE AREA PDT PDT (H) DPDT 5VA 0 5VA 5 AMP 5VA 0 AMP AMP 50VA 5 AMP 5VD 0 AMP 50VA 0 AMP 5VD 0.5 AMP 50VD 3 AMP 5VD 0.3 AMP 50VD 0.5 AMP 50VD 0.5 AMP DIVIION AREA PDT (H) 5VA AMP 8VD 5 AMP VO- VO- V- V H Model valves (DN00 & DN50 [4 & 6 ] sizes only) E - m - 4/6 3 3M

14 GA ELETRO-MEHANIAL VALVE Figure : Normally-open valves NORMALLY OPEN VALVE 6379P V- V- VO- VO- and Model valves L(+) N(-) M L N PDT PDT PDT PDT DPDT DPDT GENERAL PURPOE AREA PDT PDT (H) DPDT 5VA 0 5VA 5 AMP 5VA 0 AMP AMP 50VA 5 AMP 5VD 0 AMP 50VA 0 AMP 5VD 0.5 AMP 50VD 3 AMP 5VD 0.3 AMP 50VD 0.5 AMP 50VD 0.5 AMP DIVIION AREA PDT (H) 5VA AMP 8VD 5 AMP V- V- VO- VO M E - m - 4/6

15 GA ELETRO-MEHANIAL VALVE Available voltages and electrical data - General Purpose areas All MAXON valves are electrically actuated from a power source through the flame safeguard and/or safety control circuits. tandard valve assemblies include an internal holding solenoid on standard flow and P body constructions, or a printed circuit board on high capacity valves. The solenoid (or printed circuit board) is energized whenever the valve is powered. The motor operator on automatic reset valves is powered only during the opening stroke for normally-closed valves, or the closing stroke for normally-open versions. and Model body constructions olenoids DN0 - DN40 (3/4 - -/ ) Models DN50 - DN80 ( - 3 ) Models DN65 (-/ ) - DN00 (4 ) P Model & DN50 (6 ) Model Voltage Power Voltage Power Voltage Power 5VA, 50 Hz 3VA 5VA, 50 Hz 3VA 5VA, 50 Hz 40VA 5VA, 60 Hz 3VA 5VA, 60 Hz 3VA 5VA, 60 Hz 40VA 30VA, 50 Hz 3VA 30VA, 50 Hz 3VA 30VA, 50 Hz 40VA 30VA, 60 Hz 3VA 30VA, 60 Hz 3VA 30VA, 60 Hz 40VA 08VA, 50 Hz 3VA 08VA, 50 Hz 3VA 08VA, 50 Hz 40VA 4VD 4W 4VD 4W 4VD 4W 0VD 4W 0VD 34W 0VD 34W Motor operators Voltage Power 5VA, 50 Hz 3VA 5VA, 60 Hz 96VA 30VA, 50 Hz 3VA 30VA, 60 Hz 98VA 4VD 60W TO DETERMINE VALVE OPENING POWER: (OR LOING POWER FOR NORMALLY-OPEN VERION) Automatic reset valves Total power is the sum of the motor and solenoid power ratings for the appropriate voltage/frequency in the tables above. If supply voltages are different, then the circuits must be segregated. Manual reset valves Total power consists of only the solenoid power rating. TO DETERMINE VALVE HOLDING POWER: Holding power consists of the solenoid power rating for the appropriate voltage/frequency. DN00 and DN50 (4 and 6 ) H Model valves Printed circuit boards Voltage Power 5VA, 50 Hz 3VA 5VA, 60 Hz 3VA 30VA, 50 Hz 5VA 30VA, 60 Hz 5VA 0VD 4W Motor operators Voltage 5VA, 50 Hz 5VA, 60 Hz 30VA, 50 Hz 30VA, 60 Hz Power 667VA 39VA 667VA 39VA TO DETERMINE VALVE OPENING POWER: Total power is the sum of the motor and printed circuit board power ratings for the appropriate voltage/ frequency in the tables shown. If supply voltages are different, then the circuits must be segregated. TO DETERMINE VALVE HOLDING POWER: Holding power consists of the printed circuit board power rating for the appropriate voltage/frequency. E - m - 4/6 5 3M

16 GA ELETRO-MEHANIAL VALVE Available voltages and electrical data - Non-incendive areas All MAXON valves are electrically actuated from a power source through the flame safeguard and/or safety control circuits. tandard valve assemblies include an internal holding solenoid on standard flow and P body constructions, or a printed circuit board on high capacity valves. The solenoid (or printed circuit board) is energized whenever the valve is powered. The motor operator on automatic reset valves is powered only during the opening stroke for normally-closed valves, or the closing stroke for normally-open versions. tandard flow and P body constructions olenoids DN0 - DN40 (3/4 - -/ ) Models DN50 - DN80 ( - 3 ) Models DN65 (-/ ) - DN00 (4 ) P Models & DN50 (6 ) Model Voltage Power Voltage Power Voltage Power 5VA, 50 Hz 3VA 5VA, 50 Hz 3VA 5VA, 50 Hz 34VA 5VA, 60 Hz 6VA 5VA, 60 Hz 6VA 5VA, 60 Hz 6VA 30VA, 50 Hz 3VA 30VA, 50 Hz 3VA 30VA, 50 Hz 34VA 30VA, 60 Hz 6VA 30VA, 60 Hz 6VA 30VA, 60 Hz 6VA 4VD 8W 4VD 4W 4VD 4W 0VD 6W 0VD 34W 0VD 34W Motor operators Voltage 5VA, 50 Hz 5VA, 60 Hz 30VA, 50 Hz 30VA, 60 Hz Power 3VA 96VA 3VA 98VA TO DETERMINE VALVE OPENING POWER: (OR LOING POWER FOR NORMALLY-OPEN VERION) Automatic reset valves Total power is the sum of the motor and solenoid power ratings for the appropriate voltage/frequency in the tables above. If supply voltages are different, then the circuits must be segregated. Manual reset valves Total power consists of only the solenoid power rating. To determine valve HOLDING power: Holding power consists of the solenoid power rating for the appropriate voltage/frequency. 3M E - m - 4/6

17 GA ELETRO-MEHANIAL VALVE DIMENION AND WEIGHT Valve bodies: DN0 (3/4 ) to DN80 (3 ) Body connection A & Body connection B, D & H N ) () /4 NPT test connection H K L Body connection E H R P Body connection F L K N P H H L K R L K Valve size DN0 (3/4 ) DN5 ( ) DN3 (-/4 ) DN40 (-/ ) DN50 ( ) DN65 -/ ) DN80 (3 ) Flow capacity Body onnection Body/ bonnet material Approximate dimensions (in mm) H K L N Ø P Ø R Ø # of holes Approximate weight (in kg) Body assembly Actuator assembly Total weight A, ast iron N/A A, N/A arbon steel & E N/A 546 stainless steel F A, ast iron 96 N/A A, N/A 4 9 arbon steel & E N/A 5 0 stainless steel 5 F A, ast iron 6 N/A A, ast iron N/A 5 0 A, N/A 5 0 arbon steel & 68 E N/A 6 stainless steel F A, 56 N/A 7 3 B ast iron D, H A, 56 N/A 8 4 arbon steel & E N/A 0 6 stainless steel F A, N/A B ast iron D, H A, ast iron N/A 9 5 Flow capacity: - tandard - P body construction H - High capacity Body connection: A - NPT B - ANI flanged (IO 7005 PN0) - IO 7- threaded D - DIN PN6 flanged E - ocket welded nipple F - ocket welded nipple w/lass 50 flange (IO 7005 PN0) H - EN 09- PN6 (IO PN6) E - m - 4/6 7 3M

18 GA ELETRO-MEHANIAL VALVE Valve actuators: DN0 - DN40 (3/4 through -/ ) valves Automatic reset type (MA, MA, MA, MA) G B F H 3 ) () 3/4 NPT conduit connection ) () /4 NPT test connection 3) Terminal block cover A D E Manual reset type (MM, MM, MM, MM) NOTE: 70 mm needed for terminal block cover removal K J B H F G 3 L A D E Valve size DN0 (3/4 ) DN5 ( ) DN3 (-/4 ) DN40 (-/ ) Flow capacity Valve type Approximate dimensions (in mm) A B D E F G H J K L MM, 89 MM 4 MM, MM MA, MA MA, MA 39 MM, 89 MM 4 MM, MM MA, MA MA, MA 39 MM 89 4 MM MA MA 39 MM, 89 MM 4 MM, MM MA, MA MA, MA M E - m - 4/6

19 GA ELETRO-MEHANIAL VALVE Valve actuators: DN50 - DN80 ( through 3 ) valves Automatic reset type (MA, MA, MA, MA) B D F H G 3 A E ) () 3/4 NPT conduit connection ) () /4 NPT test connection 3) Terminal block cover Manual reset type (MM, MM, MM, MM) NOTE: 70 mm needed for terminal block removal K B L D H F G 3 J A E Valve size DN50 ( ) DN65 (-/ ) DN80 (3 ) Flow capacity Valve type Approximate dimensions (in mm) A B D E F G H J K L MM, 89 MM 43 MM, MM MA, MA 89 9 MA, MA 37 MM MM MA 89 9 MA 37 MM MM MA 89 9 MA E - m - 4/6 9 3M

20 GA ELETRO-MEHANIAL VALVE Valve bodies: DN65 (-/ ), DN80 (3 ), DN00 (4 ) and DN50 (6 ) Type Body connection A & Body connection B, D & H N ) () /4 NPT test connection H K L H R P L K Valve size DN65 (-/ ) DN80 (3 ) DN00 (4 ) DN50 (6 ) Flow capacity Body connection Body/bonnet material Approximate dimensions (in mm) H K L N Ø P Ø R Ø #of holes Approximate weight (in kg) Body assembly Actuator assembly Total weight A, N/A 9 6 B ast iron 4 D H B arbon steel & 4 D stainless steel H A, B ast iron N/A D, H B arbon steel & D, H stainless steel B ast iron D, H B arbon steel & D, H stainless steel B ast iron D, H B arbon steel & D, H stainless steel Flow capacity: - tandard - P body construction H - High capacity Body connection: A - NPT B - ANI flanged (IO 7005 PN0) - IO 7- threaded D - DIN PN6 flanged E - ocket welded nipple F - ocket welded nipple w/lass 50 flange (IO 7005 PN0) H - EN09- PN6 (IO PN6) 3M E - m - 4/6

21 GA ELETRO-MEHANIAL VALVE Valve actuators: DN65 - DN00 & DN50 (-/ -4 & 6 ) valves Automatic reset type (MA, MA, MA, MA) G F L M 3 View A-A ) () 3/4 NPT conduit connection ) () /4 NPT test connection 3) Terminal block cover K A A D E B A Manual reset type (MM, MM, MM, MM, MM) NOTE: 70 mm needed for terminal block cover removal H G J F L M N D A E A K View A-A B A Valve size DN65 (-/ ) DN80 (3 ) DN00 (4 ) DN50 (6 ) Flow capacity Valve type MM MM, MM Approximate dimensions (in mm) A B D E F G H J K L M N MA, MA 07 MA, MA 56 9 MM 07 MM, MM 388 MA, MA MA, MA 56 9 MM 07 MM, MM 388 MA, MA 07 MA, MA 56 9 MM MM E - m - 4/6 3M

22 GA ELETRO-MEHANIAL VALVE Valve bodies and actuators: DN00 & DN50 (4 & 6 ) high capacity valves HMA versions only D E F ) () 3/4 NPT conduit connection ) () /4 NPT test connection 3) Pipe size P B J G 3 R T A H Valve size DN00 (4 ) DN50 (6 ) Flow capacity Valve type Approximate dimensions (in mm) A B D E F H MA H MA Valve size DN00 (4 ) DN50 (6 ) Body connection Body/bonnet material Approximate dimensions (in mm) G H J P Ø R Ø Ø T # of holes Approximate weight (in kg) Body assembly Actuator assembly Total weight B ast iron D, H B arbon steel D, H & stainless steel B ast iron D, H B arbon steel D, H & stainless steel Flow capacity: - tandard - P body construction H - High capacity Body connection: A - NPT B - ANI flanged (IO 7005 PN0) - IO 7- threaded D - DIN PN6 flanged E - ocket welded nipple F - ocket welded nipple w/lass 50 flange (IO 7005 PN0) H - EN09- PN6 (IO PN6) 3M E - m - 4/6

23 GA ELETRO-MEHANIAL VALVE Available top assembly positions The valve top assembly can be positioned on the body in four different orientations. ee sketches below to determine the designation of the required orientation for your application. Position R Position L Position AW Position TO E - m - 4/6 3 3M

24 GA ELETRO-MEHANIAL VALVE Tandem arrangements (for simultaneous opening of main and blocking valves) General Wherever insurance underwriters or other regulatory groups require the use of a double-valve or block-andbleed system, but manual operation is preferred to the use of automatic reset valves, operation can be simplified by adding a tandem arrangement to a pair of MAXON manual reset shut-off valves. A linkage overtravel spring in the tandem arrangement latches the blocking valve just before the main valve is latched, assuring latching of both valves. If it is necessary to locate a tandem valve above arms reach, an overhead wheel and chain assembly may be added which includes a loop of chain accessible to operating personnel. To order Valves are to be specified in the usual manner and must be in top assembly position TO or AW. VO and V switches must be included on the main valve and a VO switch on the blocking valve to permit electrical connection as shown in the wiring schematic illustrated below. If overhead wheel and chain assembly is also required, specify loop length to reach appropriate operating position. Extra chain (in one foot increments) may be specified. enter line distance between valves must be within the ranges indicated in Table and shown in sketch below and must be specified at the time of order. ) Flame safeguard contact ) V in main valve 3) VO in main valve 4) VO in blocking valve 5) Main valve (normallyclosed) 6) Blocking valve (normally-closed) 7) Vent valve (normallyopen) 8) Main fuel panel light 9) For illustration only (not a wiring diagram) Wiring schematic 3 4 Main valve and blocking valve wired in parallel. V switch on main valve powers vent valve. VO switches on main and blocking valves wired in series to signal light Table. Allowable valve spacing for tandem arrangement (in mm) Valve size Minimum - Maximum - DN0 - DN40 (3/ 4 - -/ ) DN50 - DN80 ( - 3 ) DN00 & DN50 (4 & 6 ) ) Tandem main valve Tandem arrangement Tandem arrangement with overhead wheel & chain ) Tandem blocking valve 3) Tension spring 6 4) Piping by others 5) Flow 3 3 6) Tandem overhead valve 5 7) pecify loop length if overhead wheel & chain option ) ee Table above 3M E - m - 4/6

25 GA ELETRO-MEHANIAL VALVE Overhead wheel & chain assembly Overhead wheel and chain assembly allows operation of a manual reset valve in an otherwise inaccessible overhead location. A wheel is mounted onto the handle of the valve. The attached chain is weighted on one end and has a paddle handgrip on the other. Once the valve is electrically energized, pulling down on the paddle will open normally-closed versions or close normally-open versions. MAXON valve s free-handle design permits valve to trip to its rest position on any power interruption. Wheel and chain assembly includes a length of chain to position the paddle handgrip slightly below pipe centerline. A standard length of.m (7 feet) of chain is included with P and larger valve sizes and.5m (5 feet) is included with all other valves. Extra chain (in 30 cm [one foot] increments) may be specified to fit your specific location. D A B Dimensions (in mm) A B D 33 maximum maximum E - m - 4/6 5 3M

26 GA ELETRO-MEHANIAL VALVE VALVE ATUATOR PARE PART IDENTIFIATION DN0 (3/4 ) Model through DN00 (4 ) Model actuators Manual reset actuator (side view) Automatic reset actuator (side view) 4 ) Nameplate ) olenoid 3) VO motor limit/ signal switch for normally-closed valve; V for normally-open valve 4) Motor 5) Printed circuit board (PB) 6) lutch 3 DN00 & DN50 (4 & 6 ) H Model actuators (automatic reset only) MAXON nameplates include a model designation, which can be used to easily identify the exact components for each valve configuration. and Model valve spare parts include the solenoid, motor, and switches as shown above. H Model valve spare parts include the clutch, motor and circuit board as shown above. 3M E - m - 4/6

27 GA ELETRO-MEHANIAL VALVE Please read the operating and mounting instructions before using the equipment. Install the equipment in compliance with the prevailing regulations. Bedrijfs- en montagehandleiding voor gebruik goed lezen! Apparaat moet volgens de geldende voorschriften worden geïnstalleerd. Lire les instructions de montage et de service avant utilisation! L appareil doit imperativement être installé selon les règlementations en vigueur. Betriebs- und Montageanleitung vor Gebrauch lesen! Gerät muß nach den geltenden Vorschriften installiert werden. MANUFATURER AND IMPORTER ADDREE Below are the addresses and contact information for the Honeywell Maxon manufacturing location and European sales office. The European sales office serves as the importer and EU manufacturer's representative under the EU New Legislative Framework (NLF). MUNIE, INDIANA, UA MANUFATURER 0 East 8th treet P.O. Box 068 Muncie, IN Tel: Fax: EUROPEAN ALE OFFIE IMPORTER BELGIUM Maxon International BVBA Luchthavenlaan Vilvoorde, Belgium Tel: Fax: E - m - 4/6 7 3M

28 GA ELETRO-MEHANIAL VALVE WARNING The installation, operation and maintenance instructions contain important information that must be read and followed by anyone operating or servicing this product. Do not operate or service this equipment unless the instructions have been read. IMPROPER INTALLATION OR UE OF THI PRODUT OULD REULT IN BODILY INJURY OR DEATH. Nameplate and abbreviations onsult the nameplate of your valve. This lists the maximum operating pressure, temperature limitations, voltage requirements and service conditions of your specific valve. Do not exceed nameplate ratings. Description MAXON electro-mechanical valves are electrically actuated fuel shut-off valves. The valves are designed for a fast acting return to the at rest position upon removal of a control voltage signal. Motorized automatic and manual actuators are available depending on application needs. In addition, normally-closed and normally-open options are available. The normally-closed versions will shut off flow when de-energized and pass flow when energized. The normally-open versions will shut off flow when energized and pass flow when de-energized. Electro-mechanical valves are also offered in configurations that meet hazardous locations. Abbreviation or symbol M.O.P. OPENING Description Maximum operating pressure Valve opening time (for automatic valves only). Units shown in seconds. olenoid/clutch voltage and frequency M T AMB T F HUT OPEN PDT (H) PDT PDT (H) DPDT GENERAL PURPOE AREA DIVIION AREA Motor voltage and frequency Ambient temperature range Fluid temperature range Visual indication that valve is shut Visual indication that valve is open ingle pole double throw hermetically-sealed switch(es) ingle pole double throw switch(es) ingle pole double throw high capacity switch(es) (used when D motors are ordered) Double pole double throw switch(es) Designates components used in general purpose areas Designates components used in Division hazardous locations areas Valve is shut Valve is partially open Valve is full open VO-/ V-/ Valve open switch(es) Valve closed switch(es); proof of closure 3M E - m - 4/6

29 GA ELETRO-MEHANIAL VALVE omponent identification Automatic (motorized) valve Model designation MA, MA, MA, MA Manual valve Model designation MM, MM, MM 0 0 ) Access cover screws 9 9 ) Access cover 3 3 3) Visual indication 4 4 4) Mainbase 5) Nameplate 6) Actuator bolts 7) Flow arrow ) Valve body 9) Terminal block cover screws 0) Terminal block cover Automatic (motorized) valve - high capacity Model designation HMA ) Motor cover screws ) Motor cover 3) Top cover plate screws 4) Top cover plate 5) Top housing ) Top housing screws Table - Torque specifications Valve type Item number Description Torque N.m Valves DN0 - DN40 (3/4 - -/ ) Valves DN50 - DN80 ( - 3 ) Valves DN50 - DN00 ( - 4 ) H Valves DN00 - DN50 (4-6 ) Access cover screws / N.m 6 Actuator bolts 5/6-8 8 N.m 9 Terminal block cover screws / N.m Motor cover screws # N.m Access cover screws / N.m 6 Actuator bolts 3/8-6 7 N.m 9 Terminal block cover screws / N.m Motor cover screws # N.m Access cover screws / N.m 6 Actuator bolts 3/8-6 7 N.m 9 Terminal block cover screws / N.m Motor cover screws # N.m 9 Terminal block cover screws # N.m 3 Top cover plate screws / N.m 6 Top housing screws / N.m Installation. A gas filter or strainer of 40 mesh (0.6 mm) or smaller is recommended in the fuel gas piping to protect the downstream safety shut-off valves. E - m - 4/6 9 3M

30 GA ELETRO-MEHANIAL VALVE. Properly support and pipe the valve in the direction of the flow arrow on the valve body. Valve seats are directional. ealing will be maintained at full rated pressures in one direction only. ealing will be provided in reverse flow only at reduced pressures. 3. Mount valve so that open/shut window indicator will be visible to your operating personnel. The open/shut window indicator should never face downward. The valve side plates should be located in a vertical plane for best performance. Valves are usually installed in horizontal piping; however, other orientations are acceptable, subject to the above limitations. The top assemblies of all MAXON valves are field rotatable to allow installations involving conflicts with these mounting restrictions. 4. Wire the valve in accordance with all applicable local and national codes and standards. In U.. and anada, wiring must conform to the NE ANI/NFPA 70 and/or A., Part. upply voltages must agree with valve s nameplate voltage within -5%/+0% for proper operation. For electrical wiring schematic, see instructions or sample affixed inside valve terminal block cover. Grounding is achieved with a grounding screw, which is located in the top assembly. ustomer connections are provided via terminal blocks located in the top assembly. Main power wiring (0 VA or 40 VA) must be segregated from lower voltage 4 VD signal wiring, when both are required. To eliminate any potential for gas to enter the electrical wiring system, install a conduit seal fitting at the actuator conduit hub. 5. Maintain integrity of the electro-mechanical actuator enclosures by using the appropriate electrical connectors for the () 3/4 NPT conduit threaded connections. The electrical enclosure is NEMA 4 rated with an option for NEMA 4X. 6. All access cover plate screws should be tightened using an alternate cross-corner tightening pattern to the values shown in Table on page Verify proper installation and operation by electrically actuating the valve for 0-5 cycles prior to the first introduction of gas. 8. WARNING - Explosion hazard Do not connect or disconnect this equipment unless power has been removed or the area is known to be non-hazardous. ubstitution of components may impair suitability for lass I, Division (applies to MM, MA, MM and MA valves only). 9. This equipment is suitable for installation in lass I, Division Groups B,, D, and lass II Groups F and G, and lass III hazardous locations or non-hazardous locations (applies to MM, MA, MM and MA valves only). Auxiliary features Non-adjustable proof of closure switch(es) with valve seal over travel interlock Auxiliary switch for indication of full travel (open for normally-closed valves, closed for normally-open valves) Operating environment Actuators rated for NEMA 4 or optional NEMA 4X Ambient and fluid temperature range of -8 to 60 for and Model constructions Ambient and fluid temperature range of -8 to 5 for H Model constructions All valves for oxygen service or using Ethylene Propylene body seals are limited to a minimum ambient and fluid temperature of -8 3M E - m - 4/6

31 GA ELETRO-MEHANIAL VALVE ATUATOR AEMBLY ROTATION WARNING MAXON electro-mechanical valves should be ordered in a configuration compatible with planned piping. If valve orientation is not correct, the actuator assembly can be rotated in 90 increments around the valve body centerline axis using the procedure below.. hut off all electrical power and close off upstream manual cock.. Remove terminal block cover plate and disconnect power lead wires. (Tag carefully for later re-assembly.) 3. Remove conduit and electrical leads. 4. Note physical position of any signal switch actuator wands on auxiliary signal switches. 5. Unscrew the two actuator bolts screwed up from the bottom to 6 mm. DO NOT completely remove. These bolts secure the valve body to the valve s top assembly housing. 6. Gently lift the top assembly (not more than 6 mm in height); just enough to break the seal between the valve body assembly and the rubber gasket adhering to the bottom of the top housing. WARNING Lifting too far may dislodge some small parts inside the top housing, requiring complex reassembly and retesting by trained factory personnel. 7. Remove the two actuator bolts screwed up from the bottom (were partially unscrewed in step 5). 8. arefully rotate top assembly to the desired position in a plane parallel to the top of the valve body casting. Rotate the top housing about 30 beyond this position, and then rotate it back. Reposition the top housing back down onto the valve body casting. This should align the open/shut indicator with its window and provide proper alignment of the internal mechanism. 9. Realign holes in valve body casting with the corresponding tapped holes in the bottom of the top assembly housing. Be sure the gasket is still in place between the body and top housing. 0. Reinsert the actuator bolts up from the bottom through the body and carefully engage threads of the top assembly. Tighten securely.. Reconnect conduit and electrical leads, then check that signal switch wands are properly positioned and that the open/shut indicator moves freely. Failure to correct any such misalignment can result in extensive damage to the internal mechanism of your valve.. Energize valve and cycle several times from closed to full open position. Also electrically trip the valve in a partially opened position to prove valve operates properly. 3. Replace and secure terminal block cover plate and place valve in service. FIELD INTALLATION OF VALVE POI- TION WITH General hut off fuel supply upstream of valve, then de-energize valve electrically. Remove terminal block and access cover to provide access, being careful not to damage gaskets. ompare with illustrations below to identify your valve type. Replacement switches Note wand position and mounting hole location carefully, then remove screws and lift existing switch. Install replacement switch in same mounting holes on bracket and verify correct wand position. Replace existing wiring one connection at a time, following original route and placement. Add switches NOTE: Instructions below are written for normally-closed valves. For normally-open valves, reverse switch nomenclature (VO becomes V and vice versa). heck illustrations below. If your valve uses a switch mounting bracket as in Fig. &, mount switches to bracket using the mounting holes appropriate for valve type and size. For high capacity valves, mount switches on the support stand. Position bracket so V wand just touches top of actuator, then move downward slightly, depressing wand until switch clicks, then tighten mounting screws to hold this position. Pin bracket by drilling 3 mm diameter holes 6 mm deep into bracket mounting pad through drive pin holes, then tap drive pin in until flush (not required for high capacity valves). Route wires to wiring compartment as shown, then complete wiring connections and clean out metal drilling chips from previous procedure. ycle valve, checking switch actuation points carefully. (V actuates at top of stem stroke, VO at bottom.) imultaneously the valve body must be tested for switch continuity and seat leakage. Bend VO switch wands slightly if necessary to insure valve is opening fully. Replace covers, then return valve to service. E - m - 4/6 3 3M

32 # BLAK TO TERMINAL # #3 BLAK TO TERMINAL #3 OM NO N TO LUTH BLAK TO MOTOR GA ELETRO-MEHANIAL VALVE Fig. Manual reset actuator DN0 - DN80 (3/4-3 ) Models Fig. Automatic reset actuator DN65 - DN00 Models & DN50 (-/ - 4 Models and 6 ) Model Fig. 3 Automatic reset actuator DN00 & DN50 (4 & 6 ) H Models Reference mounting bracket A Reference mounting bracket B witches mount on support stand Wand position (for normally-closed valves) VO switch wand should be actuated from above V switch wand should be actuated from below Mounting brackets Mounting bracket A V switch mounts on back of bracket -6 -/ -/4 3/4, Drive pins VO switch on front Mounting bracket B 3, 4, 6 (-) 3, 4, 6 (-) -/ (-) -/ (-) V switch on back VO switch on front Bracket Mounting lots Bracket mounting holes 3M E - m - 4/6

33 GA ELETRO-MEHANIAL VALVE Tandem arrangements (for simultaneous opening of main and blocking valves) Installation instructions for tandem arrangements. Review and comply with all general valve installation instructions provided separately. (ee sketch below.). Mount both valves in fuel line with center to center spacing as originally specified, and blocking valve (without handle) downstream of main valve (with handle). 3. heck valve alignment to be certain that operating wheels lie in the same plane. 4. Remove tape from the wheel of the main valve and unwind the attached chain. Do not remove the screw holding chain to wheel; it has been factory positioned to assure correct alignment. Do not remove tension spring attached to one end of chain or the wooden block insert which preloads the spring. 5. Take free end of chain and loop it around the wheels of both main and blocking valve as shown in sketch below. Depending on the specific valve series and arrangement, tension spring may be located either above or below the wheel centerline. 6. Draw free end of chain and tension spring together so that as much slack as possible is eliminated, then insert the open eye of the spring hook through the link in the chain that will most nearly maintain this position. 7. rimp the hook shut around the chain link, then cut and discard excess chain. 8. Remove spring preload wood block insert from the tension spring, and verify that the chain is drawn tight. 9. Rotate the operating handle of the main valve fully to latching position for your particular valve, then hold handle firmly in this position while performing the next few steps. 0. Rotate blocking valve wheel fully counter-clockwise until it strikes a stop (it will slide within the loop of chain).. till holding main valve wheel in place, move blocking valve wheel approximately 6 mm to mm back in the clockwise direction. Insert the #0-4 X / screw (furnished) through the chain link that lines up with the tapped hole on bottom of blocking valve wheel, then fasten securely.. Verify that the valves are wired in parallel as shown in wiring schematic on page 3. ) Tandem main valve ) Tandem blocking valve 3) Tension spring 4) Piping by others 5) Flow direction To add wheel & chain assembly to existing tandem valves. Verify that both valves are in the same top assembly position (TO or AW). Rotate if necessary. (ee top assembly rotation instructions on page ). Bend handle of main valve outward about ut off handle of blocking valve at outer wheel face. 4. Remove hardware holding main valve wheel in place and mount new wheel and spacer to the existing wheel with new hardware provided. 5. ut chain loop to the desired length and secure to both wheels. E - m - 4/6 33 3M