Multi-Shelf Merchandiser Series. SERIES: MDW Operation Manual

Transcription

1 Multi-Shelf Merchandiser Series SERIES: MDW Operation Manual

2 WHAT IS COVERED WHO IS COVERED COVERAGE PERIOD BKI LIMITED WARRANTY 2812 Grandview Dr. Simpsonville, SC USA (864) Toll Free: (800) Fax: (864) This warranty covers defects in material and workmanship under normal use, and applies only to the original purchaser providing that: The equipment has not been accidentally or intentionally damaged, altered or misused; The equipment is properly installed, adjusted, operated and maintained in accordance with national and local codes, and in accordance with the installation and operating instructions provided with this product. The serial number rating plate affixed to the equipment has not been defaced or removed. This warranty is extended to the original purchaser and applies only to equipment purchased for use in the U.S.A. Warranty claims must be received in writing by BKI within one (1) year from date of installation or within one (1) year and three (3) months from data of shipment from the factory, whichever comes first. COB Models: One (1) Year limited parts and labor. COM Models: Two (2) Year limited parts and labor. COM convection ovens also have a two (2) year door warranty. CO1 Models: Two (2) Year limited parts and labor. Five (5) Year limited door warranty. BevLes Products: Two (2) Year limited parts and labor. Warranty period begins the date of dealer invoice to customer or ninety (90) days after shipment date from BKI, whichever comes first. WARRANTY COVERAGE This warranty covers on-site labor, parts and reasonable travel time and travel expenses of the authorized service representative up to (100) miles round trip and (2) hours travel time and performed during regular, weekday business hours. EXCEPTIONS EXCLUSIONS INSTALLATION Any exceptions must be pre-approved in advance and in writing by BKI. The extended door warranty on convection ovens years 3 through 5 is a parts only warranty and does not include labor, travel, mileage or any other charges. Negligence or acts of God, Thermostat calibrations after (30) days from equipment installation date, Air and gas adjustments, Light bulbs, Glass doors and door adjustments, Fuses, Adjustments to burner flames and cleaning of pilot burners, Tightening of screws or fasteners, Failures caused by erratic voltages or gas suppliers, Unauthorized repair by anyone other than a BKI Factory Authorized Service Center, Damage in shipment, Alteration, misuse or improper installation, Thermostats and safety valves with broken capillary tubes, Freight other than normal UPS charges, Ordinary wear and tear, Failure to follow installation and/or operating instructions, Events beyond control of the company. Leveling, as well as proper installation and check out of all new equipment - per appropriate installation and use materials is the responsibility of the dealer or installer, not the manufacturer. REPLACEMENT PARTS BKI genuine Factory OEM parts receive a (90) day materials warranty effective from the date of installation by a BKI Factory Authorized Service Center. Warranty is in lieu of all other warranties, expressed or implied, and all other obligations or liabilities on the manufacturer s part. BKI shall in no event be liable for any special, indirect or consequential damages, or in any event for damages in excess of the purchase price of the unit. The repair or replacement of proven defective parts shall constitute a fulfillment of all obligations under the terms of this warranty. BKI Worldwide, Inc. is a wholly owned subsidiary of Standex International Corporation. SS-OM Revised 07/03/12

3 Table of Contents Table of Contents Table of Contents... 1 Introduction... 2 Safety Precautions... 2 Safety Signs and Messages... 2 Safe Work Practices... 3 Operation... 4 Controls and Indicators... 4 Hardware Controls... 4 Shelf Temperature... 5 Power Up and Preheating... 5 Temperature Adjustment... 5 Operational Guidelines... 5 Unit Shutdown... 5 Installation... 6 Unpacking and Handling... 6 Floor Model... 6 Counter Model... 8 Caster Model... 8 Wiring... 8 Dimensions & Weights... 8 Maintenance Scheduled Maintenance Cleaning Troubleshooting

4 Introduction Introduction Congratulations on your purchase of a BKI MDW hot food merchandiser. It consists of heated shelves, individual shelf lighting, and electronics for powering the shelves, lighting the shelves and controlling the temperature of each shelf. This unit is for use with prepackaged foods only. This unit is manufactured by BKI which assures you of the finest in design and engineering -- that it has been built with care and dedication -- using the best materials available. Attention to the operating instructions regarding proper installation, operation, and maintenance will result in long lasting dependability to insure the highest profitable return on your investment. Safety Precautions PLEASE READ THIS ENTIRE MANUAL BEFORE OPERATING THE UNIT. If you have any questions, please contact your BKI Distributor. If they are unable to answer your questions, contact the BKI Technical Service Department, toll free: Outside the U.S., call Floor and counter units must be sealed to the mounting surface after installation to conform to NSF requirements. (Dow Corning RTV #732 Multi purpose Sealant.) Always follow recommended safety precautions listed in this manual. Below is the safety alert symbol. When you see this symbol on your equipment, be alert to the potential for personal injury or property damage. Safety Signs and Messages The following Safety signs and messages are placed in this manual to provide instructions and identify specific areas where potential hazards exist and special precautions should be taken. Know and understand the meaning of these instructions, signs, and messages. Damage to the equipment, death or serious injury to you or other persons may result if these messages are not followed. This message indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury. This message indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury. This message indicates a potentially hazardous situation, which, if not avoided, may result in minor or moderate injury. It may also be used to alert against unsafe practices. This message is used when special information, instructions or identification are required relating to procedures, equipment, tools, capacities and other special data. 2

5 Introduction Safe Work Practices Beware of High Voltage This equipment uses high voltage. Serious injury can occur if you or any untrained or unauthorized person installs, services, or repairs this equipment. Always Use an Authorized Service agent to Service Your Equipment Beware of Hot Surfaces. Do Not Touch. The shelves in this unit reach temperatures that can cause burns. Use caution when placing product on and removing product from the shelves. Do not touch any of the shelves when they are energized. A CAUTION HOT message is embossed on the front of each shelf to alert you of a potential hazard. Keep this manual with the Equipment This manual is an important part of your equipment. Always keep it near for easy access. If you need to replace this manual, contact: BKI Technical Services Department 2812 Grandview Dr. Simpsonville, S.C Or call toll free: Outside the U.S., call Protect Children Keep children away from this equipment. Children may not understand that this equipment is dangerous for them and others. NEVER allow children to play near or operate your equipment. Be Prepared for Emergencies Be prepared for fires, injuries, or other emergencies. 911 Keep a first aid kit and a fire extinguisher near the equipment. You must use a 40-pound Type BC fire extinguisher and keep it within 25 feet of your equipment. Keep emergency numbers for doctors, ambulance services, hospitals, and the fire department near your telephone. Know your responsibilities as an Employer Make certain your employees know how to operate the equipment. Make certain your employees are aware of the safety precautions on the equipment and in this manual. Make certain that you have thoroughly trained your employees about operating the equipment safely. Make certain the equipment is in proper working condition. If you make unauthorized modifications to the equipment, you will reduce the function and safety of the equipment as well as void the warranty. 3

6 Operation Operation Controls and Indicators 4 SHELF THERMOSTAT SOLID BACK UNITS - ACCESS FROM FRONT PASS-THRU UNITS - ACCESS FROM BACK POWER OFF ON LIGHTS OFF ON POWER & LIGHT SWITCH PLATE SOLID BACK UNITS - LOCATED ON FRONT PASS-THRU UNITS - LOCATED ON BACK Figure 1 Hardware Controls Item # Function 1 Main Power Switch Turns power On or Off to the entire unit. When placed in the On position, the shelf heaters are powered and the lights illuminate. When placed in the Off position, power is removed from the entire unit. 2 Lights Circuit Breaker Provides circuit protection for the Lights. When placed in the On position (with the Power Switch in the On position) the illuminate. When placed in the Off position (with the Power Switch in the On position) power is removed from lights. If an overload occurs in the light circuit, the Circuit Breaker will trip causing the actuator to move to the Off position. 3 Thermostat for Base Warmer (Bottom Shelf) 4 Thermostat for Individual Shelf Controls the surface temperature of the Base Warmer (Bottom Shelf). Set the Thermostat dial to a larger number setting to increase the temperature or a lower number setting to decrease the temperature. Controls the surface temperature of the individual Shelf. Set the Thermostat dial to a larger number setting to increase the temperature or a lower number setting to decrease the temperature. 4

7 Operation Shelf Temperature The temperature of the shelves is controlled by a thermostat on each shelf and on the base of the unit (see Figure 1). Set each shelf thermostat on 9 for the initial start up of the unit. Power Up and Preheating 1. Ensure that the power supply cord is connected to an appropriate power receptacle. 2. Place the POWER ON/OFF switch in the ON position. 3. Place the LIGHTS ON/OFF circuit breaker in the ON position. 4. Allow the unit to preheat for a minimum of 30 minutes before loading it with product. Check Federal and State Health and Sanitation Regulations for internal temperature required for holding cooked foods for sale. Maintaining these temperatures often tends to allow continued cooking of certain products. Therefore, smaller amounts of bulk foods should be displayed at non-peak periods and the unit refilled as needed. This equipment is not designed to heat-up or cook food. All meat and vegetable products should be preheated to a minimum of 160 F (70 C) before being placed in the unit. Temperature Adjustment After placing the product onto the shelves, it may be necessary to adjust the individual thermostats in order to maintain the proper internal temperature for the product on display. A thermometer should be used to read the internal temperature of each product. The thermostats should be adjusted to the lowest possible setting that will maintain the proper product temperature. Operational Guidelines Only use product packaging suitable for the application. Keep portable meat thermometers on hand. Check the food temperatures hourly. Rotate the food products. Foods loaded in first should be served first as much as is practical. Foods held for long periods of time are more difficult to maintain at proper temperature. Also, freshness and product quality diminish if foods are held too long. Most areas of the country have sanitation regulations governing how long foods can be held. Make certain to check with your local authorities. Unit Shutdown 1. Remove product from the unit. 2. Place the POWER ON/OFF circuit breaker in the OFF position. 3. Place the LIGHTS ON/OFF circuit breaker in the OFF position. 4. After the unit has cooled down, remove any residue from the shelves and clean the unit thoroughly. 5

8 Installation Installation Unpacking and Handling YOU are responsible for filling all freight claims with the delivering truck line. Inspect all cartons and crates for damage as soon as they arrive. If damage to cartons or crates is found, or if a shortage is found, note this on the bill of lading (all copies) prior to signing. If damage is found when the equipment is opened, immediately call the delivering truck line and follow up the call with a written report indicating concealed damage to your shipment. Ask for an immediate inspection of your concealed damage item. Packaging material MUST be retained to show the inspector from the truck line. Do not place heavy objects on top of the unit or damage could occur. The units are not structurally designed to support excessive external loading. Move the unit as close as possible to its permanent location before moving it off of the shipping pallet. Make certain there are no separately packed accessories before discarding packaging. Floor Model Follow the procedure below to level the unit and mount the kick plates. See Error! Reference source not found.. 1. Slide kick plates, ends first, between the base frame and outer panels. Secure in raised position with tape. Make sure that the end kick plates fit behind the front and rear kick plates. 2. Using a carpenter s level on the lowest shelf, level the unit by adjusting the leg levelers at the corners of the unit. 3. Raise the low end of the unit to level it, do not lower the high end. 4. Check for level side-to-side and front-to-back. 5. Remove the tape holding the kick plates in raised position. 6. Make certain that the kick plates are flush to the floor. 7. Drill 9/64 diameter holes in the base frame to match the pre-drilled holes in the kick plates. 8. Attach the kick plates to the base frame with the #8x1/2 black sheet metal screws provided (SCR355). 9. Seal kick plates to floor using a silicone-type sealant (Dow Corning RTV #732 or equivalent). 6

9 Installation Figure 2 7

10 Installation Counter Model Counter mounted units must be mounted on a level surface that can support the weight of the unit and its contents. Use a carpenter s level to level the unit. These units are to be sealed to the counter if required by local health codes. Seal the perimeter of the units to the counter using a silicone-type sealant (Dow Corning RTV #732 or equivalent). Caster Model Caster mounted units must be moved to a permanent location and the two swivel casters locked before using. Wiring A wiring diagram for your specific model is included in this manual. The wiring diagram provides electrical specifications, an electrical schematic and a parts list. Refer to this wiring diagram and the unit rating plate for electrical information. All electrical connections should be in compliance with the NEC and all applicable local codes by a licensed electrician. Refer to the wiring diagram furnished with your unit for the electrical specifications. Dimensions & Weights Electrical Specifications refer Wiring Diagram listed for each model. WIDTH + 1/2 in [13 mm] 41 1/8 in [1045 mm] Counter Model 10 1/2 in [266 mm] 10 5/16 in [263 mm] 10 5/8 in [269 mm] 20 5/8 in [525 mm] 56 3/16 in [1426 mm] Floor Model 10 5/8 in [269 mm] 20 5/8 in [523 mm] 8 1/16 in [205 mm] 23 1/8 in [587 mm] 25 15/16 in [659 mm] CASCADE 16 in [407 mm] VERTICAL 25 15/16 in [659 mm] WIDE VERTICAL WIDTH + 2 9/16 in [65 mm] WIDTH /16 in [122 mm] Figure 3 3 Shelf Merchandisers Shipping Wt. Model Diagram Width Wiring Diagram Counter Floor MDW36-3C CASCADE 36 in [914 mm] EB lb [136 kg] 360 lb [163 kg] MDW36-3V VERTICAL 36 in [914 mm] EB lb [91 kg] 240 lb [163 kg] MDW36-3WV WIDE VERTICAL 36 in [914 mm] EB lb [150 kg] 390 lb [177 kg] MDW48-3C CASCADE 48 in [1219 mm] EB lb [172 kg] 440 lb [200 kg] MDW48-3V VERTICAL 48 in [1219 mm] EB lb [127 kg] 320 lb [145 kg] MDW48-3WV WIDE VERTICAL 48 in [1219 mm] EB lb [190 kg] 480 lb [218 kg] 8

11 WIDTH + 1/2 in [13 mm] 50 1/8 in [1273 mm] Counter Model 9 in [229 mm] 10 1/2 in [266 mm] 10 5/8 in [269 mm] 65 3/16 in [1655 mm] Floor Model 10 5/16 in [263 mm] 20 5/8 in [523 mm] 10 5/8 in [269 mm] 20 5/8 in [523 mm] 8 1/16 in [205 mm] 23 1/8 in [587 mm] 25 15/16 in [659 mm] CASCADE 16 in [407 mm] VERTICAL Figure 4 4 Shelf Merchandisers 25 15/16 in [659 mm] WIDE VERTICAL WIDTH + 2 9/16 in [65 mm] WIDTH /16 in [122 mm] Shipping Wt. Model Diagram Width Wiring Diagram Counter Floor MDW36-4C CASCADE 36 in [914 mm] EB lb [218 kg] 540 lb [245 kg] MDW36-4V VERTICAL 36 in [914 mm] EB lb [172 kg] 420 lb [191 kg] MDW36-4WV WIDE VERTICAL 36 in [914 mm] EB lb [231 kg] 570 lb [258 kg] MDW48-4C CASCADE 48 in [1219 mm] EB lb [245 kg] 620 lb [281 kg] MDW48-4V VERTICAL 48 in [1219 mm] EB lb [208 kg] 500 lb [227 kg] MDW48-4WV WIDE VERTICAL 48 in [1219 mm] EB lb [272 kg] 660 lb [299 kg] WIDTH + 1/2 in [13 mm] 9 in [229 mm] 59 1/8 in [1502 mm] Counter Model 9 in [229 mm] 10 1/2 in [266 mm] 74 3/16 in [1884 mm] Floor Model 10 5/16 in [263 mm] 20 5/8 in [523 mm] 10 5/8 in [269 mm] 20 5/8 in [523 mm] 8 1/16 in [205 mm] 23 1/8 in [587 mm] 25 15/16 in [659 mm] CASCADE 16 in [407 mm] 25 15/16 in [659 mm] WIDTH + 2 9/16 in [65 mm] WIDTH /16 in [122 mm] Figure 5 5 Shelf Merchandisers Shipping Wt. Model Diagram Width Wiring Diagram Counter Floor MDW36-5C CASCADE 36 in [914 mm] EB lb [218 kg] 540 lb [245 kg] MDW36-5V VERTICAL 36 in [914 mm] EB lb [172 kg] 420 lb [191 kg] MDW36-5WV WIDE VERTICAL 36 in [914 mm] EB lb [231 kg] 570 lb [258 kg] MDW48-5C CASCADE 48 in [1219 mm] EB lb [245 kg] 620 lb [281 kg] MDW48-5V VERTICAL 48 in [1219 mm] EB lb [208 kg] 500 lb [227 kg] MDW48-5WV WIDE VERTICAL 48 in [1219 mm] EB lb [272 kg] 660 lb [299 kg] 9

12 Maintenance Maintenance Scheduled Maintenance Failure to comply with the maintenance below could result in a serious accident. Electrocution, equipment failure or property damage could result if an unlicensed electrician performs electrical repair. Ensure that a licensed electrician performs electrical repair. Use the following table to help manage scheduled maintenance activities. Frequency Performed By Part Activity Daily User Unit Clean the entire Unit. Refer to the cleaning procedure below. Monthly User Shelf Power ON/OFF Circuit Breaker Press push-to-test button to test overload, short circuit and ground fault protection capability. Cleaning This unit should be cleaned at the end of each day. Use the following procedure: Failure to remove power from this unit may cause severe electrical shock. This unit may have more than one disconnect switch. 1. Place the POWER ON/OFF circuit breaker in the OFF position. 2. Place the LIGHTS ON/OFF circuit breaker in the OFF position. 3. Allow unit to cool down. 4. Disconnect power from the unit by unplugging it from the power receptacle. 5. Remove product from the shelves. Always wear appropriate personal protection equipment during the cleaning process to guard against possible injury. Using abrasive cleaners may damage the cabinet finish. Use mild soap and water only. DO NOT USE OVEN CLEANER on this machine. Caustic cleaners will damage the equipment. Never get excess water on the unit as this can cause damage to the unit. This equipment is not intended to be cleaned with a water jet. 6. Use a mild soap and water solution to clean the unit. 7. Sponge the inside and outside with a mild soap and water solution. 8. Wipe the unit dry with a soft, clean cloth. 10

13 Maintenance Troubleshooting Refer to the table below for troubleshooting information. Problem Cause Possible Solution Shelves Not Heating and Lights Not On Unit not plugged into power receptacle. No Power to the unit. Power switch is OFF and Lights circuit breaker is OFF. Ensure unit power cord is connected to appropriate power receptacle. Check circuit breaker or fuses at building power panel. If problem persists, contact an authorized BKI service agent for corrective action. Place the Power circuit breaker ON and the Lights circuit breaker ON. No Heat to Single Shelf Failed shelf component. Contact an authorized BKI service agent for corrective action. Individual Light is not On Failed Fluorescent Lamp. Replace lamp only with BKI shatter-proof lamp. Holding Temperature Not Adequate Fail Lamp Ballast Unit has not been preheated. Product is below 160 F when loaded. Shelf temperature control not set properly. Failed shelf component. Contact an authorized BKI service agent for corrective action. Refer to the preheating section on page 5. If problem persists, contact an authorized BKI service agent for corrective action. Check product temperature before loading the unit. Adjust the shelf temperature control. Refer to the section entitled Temperature Adjustment on page 5. Contact an authorized BKI service agent for corrective action. 11

14 MDW36-3C C H2 COMPONENT LEGEND EB C0362 C0363 C0364 C0359 C0360 C0361 FL0041 CORDSET, 120V (USA), 20"x36", 120V, 20"x36", 208V, 20"x36", 230V, 10"x36", 120V, 10"x36", 208V, 10"x36", 230V GND TERMINAL END SP 12

15 MDW36-3V C EB C0359 C0360 C0361 FL0041 CORDSET, 120V (USA), 10"x36", 120V, 10"x36", 208V, 10"x36", 230V GND TERMINAL END SP 13

16 MDW36-3WV C COMPONENT LEGEND EB C0362 C0363 C0364 FL0041 CORDSET, 120V (USA), 20"x36", 120V, 20"x36", 208V, 20"x36", 230V GND TERMINAL END SP 14

17 MDW36-4C C H2 COMPONENT LEGEND EB C0362 C0363 C0364 C0359 C0360 C0361 FL0041 CORDSET, 120V (USA), 20"x36", 120V, 20"x36", 208V, 20"x36", 230V, 10"x36", 120V, 10"x36", 208V, 10"x36", 230V GND TERMINAL END SP 15

18 MDW36-4V C COMPONENT LEGEND EB C0359 C0360 C0361 FL0041 CORDSET, 120V (USA), 10"x36", 120V, 10"x36", 208V, 10"x36", 230V GND TERMINAL END SP 16

19 MDW36-4WV C COMPONENT LEGEND C0363 C0364 FL0041, 20"x36", 208V, 20"x36", 230V GND TERMINAL END SP 17

20 MDW36-5C C H2 C0363 C0364 C0360 C0361 FL0041, 20"x36", 208V, 20"x36", 230V, 10"x36", 208V, 10"x36", 230V GND TERMINAL END SP 18

21 MDW36-5V C COMPONENT LEGEND EB C0359 C0360 C0361 FL0041 CORDSET, 120V (USA), 10"x36", 120V, 10"x36", 208V, 10"x36", 230V GND TERMINAL END SP 19

22 MDW36-5WV C COMPONENT LEGEND C0363 C0364 FL0041, 20"x36", 208V, 20"x36", 230V GND TERMINAL END SP 20

23 MDW48-3C C H2 COMPONENT LEGEND EB C0368 C0369 C0370 C0365 C0366 C0367 FL0042 CORDSET, 120V (USA), 20"x48", 120V, 20"x48", 208V, 20"x48", 230V, 10"x48", 120V, 10"x48", 208V, 10"x48", 230V GND TERMINAL END SP 21

24 MDW48-3V C COMPONENT LEGEND EB C0359 C0360 C0361 FL0042 CORDSET, 120V (USA), 10"x36", 120V, 10"x36", 208V, 10"x36", 230V GND TERMINAL END SP 22

25 MDW48-3WV C COMPONENT LEGEND C0369 C0370 FL0042, 20"x48", 208V, 20"x48", 230V GND TERMINAL END SP 23

26 MDW48-4C C H2 COMPONENT LEGEND C0369 C0370 C0366 C0367 FL0042, 20"x48", 208V, 20"x48", 230V, 10"x48", 208V, 10"x48", 230V GND TERMINAL END SP 24

27 MDW48-4V C COMPONENT LEGEND EB C0365 C0366 C0367 FL0042 CORDSET, 120V (USA), 10"x48", 120V, 10"x48", 208V, 10"x48", 230V GND TERMINAL END SP 25

28 MDW48-4WV C COMPONENT LEGEND C0369 C0370 FL0042, 20"x48", 208V, 20"x48", 230V GND TERMINAL END SP 26

29 MDW48-5C C H2 COMPONENT LEGEND C0764 C0765 C0171 C0178 FL0042, 20"x48", 208V, 20"x48", 230V, 10"x48", 208V, 10"x48", 230V GND TERMINAL END SP ALTERNATE TERMINAL BLOCK FOR NON-CORD CONNECTED UNITS 27

30 MDW48-5V C C0366 C0367 FL0042, 10"x48", 208V, 10"x48", 230V GND TERMINAL END SP 28

31 MDW48-5WV C COMPONENT LEGEND C0369 C0370 FL0042, 20"x48", 208V, 20"x48", 230V GND TERMINAL END SP 29

32 NOTES 2812 Grandview Dr., Simpsonville, S.C , USA Made and printed in the U.S.A SS-OM Revised 07/03/12