Cincinnati, OH USA

Size: px

Start display at page:

Download "Cincinnati, OH USA"

Elisabeth Powell
5 years ago
Views:

1 Part No PE Revised November 2007 Hot Dog Roller Grills Non-Stick Instruction Manual Model #8023PE, Model #8024PE and Model #8025PE Model #8023SLPE, Model #8024SLPE and Model #8025SLPE Model #8023PE shown Cincinnati, OH USA

2 Table of Contents I. Safety Precautions..3 II. Installation Instructions...4 III. Operating Instructions...4 IV. Cleaning Instructions V. Maintenance 5 VI. System Parts Location Guide..6-7 VII. Ordering Spare Parts....8 VIII. Electrical Schematic...9 IX. Warranty

3 SAFETY PRECAUTIONS

4 INSTALLATION INSTRUCTIONS Roller Dog, Non-Stick CHECKING SHIPMENT Unpack carton and check thoroughly for any damage which may have occurred during transit. Damage claims should be filed immediately with the transportation company. Gold Medal Products is not responsible for damage that may occur in transit. ELECTRICAL REQUIREMENTS Machine MUST be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury or death. Do NOT immerse any part of this equipment in water. Always unplug the equipment before cleaning or servicing. Do not use excessive water when cleaning. Your Hot Dog Roller Grill requires a 120 volt/60 cycle/15 amp outlet, and should be operated on a dedicated line. Make sure to have a qualified electrician supply the proper electrical requirements before plugging the machine into an outlet. OPERATING PROCEDURES 1. Place hot dogs on rollers. Turn heat to designated temperature. Left knob controls the heat of one set of five (5) rollers and the right controls the other set of five (5) rollers. 2. For low heat, set control(s) to LOW using one or both sets of rollers. For high capacity, set control(s) to MEDIUM or HIGH using both sets of rollers. CARE AND CLEANING INSTRUCTIONS Although corrosion resistant, stainless steel machine surfaces should be cleaned daily to prevent pitting. Do NOT use anything abrasive for cleaning (e.g. steel wool). Non-stick roller assemblies should be cleaned only with soft cloth or sponge and mild detergent or cleaner and water. 1.!! UNPLUG THE POWER CORD FROM THE OUTLET!! 2. Remove any remaining hot dogs from rollers. 3. Remove drip pans and clean thoroughly. 4. Use a mild detergent, soap and water, or soda-water to clean the roller grill. Rinse after washing and dry thoroughly before using. 5. When unit has been thoroughly cleaned and dried, reinsert drip pans beneath the rollers. 6. The unit is now cleaned and ready for operation, and it is safe to plug it back in. 4

MAINTENANCE INSTRUCTIONS Machine MUST be properly

Failure to do so could result in serious injury or

Do NOT immerse any part of this equipment in water.

5 MAINTENANCE INSTRUCTIONS Machine MUST be properly grounded to prevent electrical shock to personnel. Failure to do so could result in serious injury or death. Do NOT immerse any part of this equipment in water. Always unplug the equipment before cleaning or servicing. Do not use excessive water when cleaning. 5

8023PE-Medium Roller Assembly (10) 8024PE-Short Roller

Teflon Bearing (20) 8023PE-Drip Pan 8024PE-Drip Pan

8023PE-Bottom Cover 8024PE-Bottom Cover 8025PE-Bottom Cover

6 8023PE-Medium Roller Assembly (10) 8024PE-Short Roller Assembly (10) 88231PE 8025PE-Long Roller Assembly (10) 88233PE Teflon Bearing (20) 8023PE-Drip Pan 8024PE-Drip Pan 8025PE-Drip Pan Knob, Control (2) Switch, DPST Rocker (2) 8023PE-Bottom Cover 8024PE-Bottom Cover 8025PE-Bottom Cover End Cover (2) Strain Relief #SR-10-2 Lead-In Cord 15A Plug Crutch Tip (4) Glide Feet (4) 6

Motor, 120V CW (Gray Fan) Heat Control, Minidogeroo (2) Switch, DPST Rocker

(2) This assembly includes all chain idler parts illustrated.

Spring Sprocket, Drive (2) 90W Heat Element (10) ( for 8023) ( 87376 for

Plate (4) ¼ - 20 x ½ Hex Head Bolt Upper Drive Chain #10 Flat Washer St.

7 Motor, 120V CW (Gray Fan) Heat Control, Minidogeroo (2) Switch, DPST Rocker (2) Motor, 120V CCW (Black Fan) Support, Element (2) Chain Idler Assy. (2) This assembly includes all chain idler parts illustrated. Positraction Sprocket (8) Lower Drive Chain Master Link Drive Chain (2) Spring Sprocket, Drive (2) 90W Heat Element (10) ( for 8023) ( for 8024) (125W Heat Element for 8025) Insulator Board (2) Conductor Plate (4) ¼ - 20 x ½ Hex Head Bolt Upper Drive Chain #10 Flat Washer St. Stl. Med Split Lock Washer ¼ Spring Pivot 8-32 x ¾ Phil Pan SMS Idler Sprocket Idler Pivot Idler Bracket 7

8 ORDERING SPARE PARTS 8

9 9

10 WARRANTY WE WARRANT to the original purchaser the Gold Medal equipment sold by us to be free from defects in material or workmanship under normal use and service. Our obligation under this warranty shall be limited to the repair or replacement of any defective part for a period of six (6) months from the date of sale to the Original Purchaser with regard to labor and two (2) years with regard to parts and does not cover damage to the equipment caused by accident, alteration, improper use, voltage, abuse, or failure to follow instructions. THIS WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES EXPRESSED OR IMPLIED, AND OF ALL OTHER OBLIGATIONS OR LIABILITIES ON OUR PART, INCLUDING THE IMPLIED WARRANTY OF MERCHANTIBILITY. THERE ARE NO WARRANTIES WHICH EXTEND BEYOND THE DESCRIPTION ON THE FACE HEREOF. We neither assume, nor authorize any other person to assume for us, any other obligation or liability in connection with the sale of said GOLD MEDAL equipment or any part thereof. The term Original Purchaser as used in this warranty shall be deemed to mean that person, firm, association, or corporation who was billed by the GOLD MEDAL PRODUCTS COMPANY, or their authorized distributor for the equipment. THIS WARRANTY HAS NO EFFECT AND IS VOID UNLESS THE ORIGINAL PURCHASER FIRST CALLS GOLD MEDAL PRODUCTS COMPANY AT TO DISCUSS WITH OUR SERVICE REPRESENTATIVE THE EQUIPMENT PROBLEM, AND, IF NECESSARY, FOR INSTRUCTIONS CONCERNING THE REPAIR OR REPLACEMENT OF PARTS. NOTE: This equipment is manufactured and sold for commercial use only. GOLD MEDAL PRODUCTS COMPANY Medallion Drive Cincinnati, Ohio USA Phone: Fax: The text, descriptions, graphics and other material in this publication are the proprietary and exclusive property of Gold Medal Products Company and shall not be used, copied, reproduced, reprinted or published in any fashion, including website display, without its express written consent. 10

Hot Dog Roller Grills Instruction Manual Model #8023, Model #8024 and Model #8025 Model #8023SL, Model #8024SL and Model #8025SL

Part No. 87630 Revised November 2007 Hot Dog Roller Grills Instruction Manual Model #8023, Model #8024 and Model #8025 Model #8023SL, Model #8024SL and Model #8025SL Model #8023 shown Cincinnati, OH 45241-4807