2 GURTECH High Pressure Foot Operated Grease Gun Supplied with 2m delivery hose and 'G Coupler' Grease Coupling

Transcription

1 Workshop 2007

2 Greasing Equipment Foot Operated Grease Gun / G Coupler GURTECH High Pressure Foot Operated Grease Gun Supplied with 2m delivery hose and 'G Coupler' Grease Coupling Delivery rate: 2.7ml per stroke Delivery pressure: 10,000psi (650 bar) Grease capacity: 8 Kg Bulk fi ll Delivery hose: 2 metre x 1/4" 2 Wire Coupler thread: 1/8" female Pump mechanism: 2 Stage self priming with pressure return valve Foot operated grease gun GGUN Activate trigger to engage / disengage. Can easily be done with one hand Greasing at 10,000psi with no hands needed to align coupler and no leaking grease. GURTECH 'G Coupler' Grease Coupler Max Pressure:10,000psi (690 Bar) Coupler Thread: 1/8" BSP or M10x1 Grease Gun Compatibility: Pneumatic, Manual and Electric Seal: Durable nitrile rubber seal for longevity under high pressure Lock-on Mechanism: Four hardened spring steel jaws THREAD 'G Coupler ' grease coupler 1/8" BSP GC18 'G Coupler ' grease coupler M10x1 GC10 REPLACEMENT PARTS TO SUIT Steel jaw repair kit GCRP 'G Coupler' Grease Coupler - Long Series Ideal for PTO Shaft greasing application THREAD 'G Coupler ' long series coupler 1/8" BSP GC18L 'G Coupler ' long series coupler M10x1 GC10L REPLACEMENT PARTS TO SUIT Steel jaw repair kit GCRP 'G Coupler' Display Stand Steel display unit with hanging hooks Test grease nipple and fl exible hose with 'G Coupler' attached to stand Note: Hang packs are not supplied with display stand and must be ordered separately Display stand for G Coupler GCSTAND 2

3 Greasing Equipment Grease Guns Two Handed Grease Gun (500g) Suitable for 500g threaded grease cartridges Working pressure: 12000PSI Accessories Included 500mm fl exi tube - 1/8" thread 150mm rigid tube - 1/8" thread 4 jaw grease coupler - 1/8" thread Conversion bush for 400g spin-on cartridge First time priming instructions shown below Two handed grease gun c/w accessories Supplied Boxed PGS500 Push a small amount of grease out of the grease cartridge Insert cartridge into gun and tighten Pump gun to prime and you are ready to grease Conversion Bush for 400g Spin-On Cartridge For use with PGS500 grease gun Conversion bush for 400g spin-on cartridge PGS500AD1 Lever Grease Gun (400g) Suitable for 400g cartridges Working pressure: 10000PSI Accessories Included 300mm fl exi tube - 1/8" thread 150mm rigid tube - 1/8" thread 4 jaw grease coupler - 1/8" thread Lever grease gun c/w accessories Supplied Boxed PGS400 Telescopic Grease Gun (100ml) Ideal for Chainsaws and small applications Instructions: Expand shaft of gun Remove rear cap and fi ll with grease Replace cap to start greasing Telescopic grease gun FGP

4 Greasing Equipment Grease Gun Accessories Grease Gun Tubes No mm fl exi tube (10mm) - 1/8" thread PGS mm fl exi tube (10mm) - M10x1 thread FP mm fl exi tube (8mm) - 1/8" thread PGS mm fl exi tube (10mm) - 1/8" thread PGS mm Rigid tube - 1/8" thread Jaw Grease Coupler 4 jaw grease coupler - 1/8" thread PGS4J 4 jaw grease coupler - M10x1 thread FP12631 Profi le 90º Grease Coupler 90º grease coupler - M10x1 thread PGS90 Bulk Filling Nipple Filler nipple with 1/8" thread

5 Greasing Equipment Spin-On Cartridge Grease Guns 400g Spin-On Cartridge System - Quick and Easy, No-Mess Cartridge Changing 1. Remove cap from cartridge and push the grease up a little 2. Simply insert cartridge into gun 3. Just screw the cartridge tight and you are ready to go Lever Grease Gun 400g Spin-On Cartridge Type Quick and Easy, No-Mess Cartridge Changing Lever grease gun for quick & effortless high pressure greasing Designed to work with 400g spin-on grease cartridge Spin-on cartridge works on vacuum technology that ensures full utilization of grease in the cartridge eliminating priming issues No air pockets, hence no air bleeding required Working pressure: PSI Accessories Included: 300mm fl exi tube - 1/8" thread 150mm rigid tube - 1/8" thread 4 jaw grease coupler - 1/8" thread Lever grease gun 400g spin-on cartridge type Supplied Boxed PGS600 Pistol Grease Gun 400g Spin-On Cartridge Type Quick and Easy, No-Mess Cartridge Changing Pistol grease gun for quick & effortless high pressure greasing Designed to work with 400g spin-on grease cartridge Spin-on cartridge works on vacuum technology that ensures full utilization of grease in the cartridge eliminating priming issues No air pockets, hence no air bleeding required Working pressure: 5000 PSI Accessories Included: 300mm fl exi tube - 1/8" thread 100mm rigid tube - 1/8" thread 4 jaw grease coupler - 1/8" thread Pistol grease gun 400g spin-on cartridge type Supplied Boxed PGS

6 Greasing Equipment Spin-On Grease Cartridges 400g Spin-on Grease Cartridges Quick and Easy, No-Mess Cartridge Changing Available in 3 Premium quality grease for various applications Use in conjunction with PGS600 & PGS700 grease guns. Further details on page 11b Premium Quality Multipurpose Grease NLGI No. 2 Highly versatile multipurpose lithium grease for use in all anti-friction and plain bearings subject to high load conditions. Used extensively throughout the agricultural, industrial and automotive sectors Temperature (-20 to +140ºC) High degree of corrosion protection Excellent anti-wear performance Clean, clear smooth appearance Colour: Light Brown 400g Multipurpose spin-on grease cartridge GC400LSEP2 Longlife High Temperature Grease NLGI No. 2 A specially developed lithium complex grease for use in harsh agricultural, industrial and automotive environments. Exceptional mechanical stability greatly extends lubrication intervals. High Temperature (-20 to +150ºC) Long Life Excellent corrosion resistance for operating in wet conditions Exceptional Anti-wear performance Colour: Blue 400g Longlife high temperature spin-on grease cartridge GC400LSHP2 Heavy Duty Graphite Grease NLGI No. 2 Designed for heavy duty applications where adhesion, shock loading and good corrosion protection is needed. Ideal for use on bucket pins and bushes on earthmoving equipment. Temperature (-20 to +140ºC) High level of lubrication solids substantially extends component life Adhesion improver provides long lasting protection Smooth appearance Colour: Grey 400g heavy duty graphite spin-on grease cartridge GC400LSPBL 6

7 Greasing Equipment Grease Cartridges Premium Quality Blue Lithium EP2 SV Grease NLGI No. 2 Premium quality high performance, mineral oil, lithium thickened NLGI No2 lubricating grease suitable for multi-purpose applications. Lithium EP2 SV is formulated on a higher viscosity base oil than standard Lithium EP2 greases to give higher performance Temperature (-20 to +140ºC) High degree of corrosion protection Excellent anti-wear performance Long Life Colour: Blue 500g Blue litium EP2 SV grease cartridge GC500EP2SV Premium Quality Multipurpose Grease NLGI No. 2 Highly versatile multipurpose lithium grease for use in all anti-friction and plain bearings subject to high load conditions. Used extensively throughout the agricultural, industrial and automotive sectors Temperature (-20 to +140ºC) High degree of corrosion protection Excellent anti-wear performance Clean, clear smooth appearance Colour: Light Brown 400g Multipurpose grease cartridge SP03003Z Longlife High Temperature Grease NLGI No. 2 A specially developed lithium complex grease for use in harsh agricultural, industrial and automotive environments. Exceptional mechanical stability greatly extends lubrication intervals. High Temperature (-20 to +150ºC) Long Life Excellent corrosion resistance for operating in wet conditions Exceptional Anti-wear performance Colour: Blue 400g Longlife high temperature grease cartridge GC400HP2 Graphite Grease Water resistant multi-purpose grease with solid lubricant additives for lubricating roller bearings and slide bearings that are subject to high mechanical and thermal loads According to DIN 51502: KPF 2 K-30 and ISO/DIS : ISO-L-XCCHB 2 Dropping Point +190ºC Temperature range from -35º to +130ºC 400g graphite cartridge SP

8 Greasing Equipment Grease Bucket / Tube / Spray EP Transmission Grease EP liquid gearbox grease is a natural-coloured, long-fi bre sodium soap lubricating grease based on mineral oil. Suitable for lubricating rotary mower gearboxes, industrial gearboxes, manual gearboxes and other stationary engine/gearbox units. (When using EP liquid gearbox grease, the size, power and seal of the gearbox must be taken into account.) Temperature range: -30 C to +100 C Drop point: approx C (DIN ISO 2176) Water resistance: 3 90 (DIN T.1) Base oil viscosity at 40 C: approx. 130 mm²/s (DIN ) Designation: GP 0 H-30 (DIN ), ISO-L-XCABB 0 (ISO ) 5 Kg Bucket of EP transmission grease ND9091 Multi-Purpose Grease Tube (250ml) Work stable 250ml Tube with screw cap Water resistant Dropping point 190 C Designation as per DIN 51502: K 2K-30 Area of application from -35 C to +120 C Oxidation resistance for slide and roller bearings High-Performance multi-purpose grease - lithium soap-based 250ml grease tube with screw cap FGP White Spray Grease (500ml) Lubricating grease with excellent adhesion and high viscosity, for the treatment of mechanical parts made of metal or plastic. Fat White has excellent mechanical and thermal stability and excellent corrosion properties. Weatherproof, diluted acids and alkalis, the White Grease is waterproof and ph-neutral. The White Grease contains PTFE (Polytetrafl uoroethylene) and prevents wear and galling. Temperature range: -30 C to +160 C. White spray grease 500ml

9 Greasing Equipment Hand Operated Greaser / Accessories K6 Mini-Lube to suit 3Kg Bucket Portable manual greasing system designed for professional greasing Features Supplied with 1.5 metre 1/2" deliver hose and KR Grease Gun Suitable for grease up to and including NLGI No.2 360º swivel to prevent hose kink Fully sealed to prevent contamination Specifi cation Gun Pressure (on High Pressure) : 69,000 kpa (10,000 psi, 690 bar) Output: 1.25g on High Volume switch, 0.45g on High Pressure switch K6 Super Lube to suit 3Kg Bucket K6 Booster Gun c/w 360º Swivel Suitable for air powered greasing applications. Supplied as standard gun on the P3, P6 and P8 complete grease pumps Features A couple of simple presses of the trigger will double output pressure Specifi cation Maximum Operating Pressure: 69,000 kpa (10,000 psi, 690 bar) Thread Inlet: 1/4" NPT Female Booster Gun to suit air powered greasing applications B2 Pressure Gun Suitable for manual powered greasing applications Features Can deliver grease at either High Pressure or High Volume 360º swivel to prevent hose kinking Specifi cation Gun Pressure: kpa (10,000 psi, 690 bar) Output: 1.25g on High Volume switch, 0.45g on High Pressure switch Pressure Gun to suit manual powered greasing applications KR ZSB Swivel Swivel allowing 360º movement 360º Swivel - thread 1/4" ZSB KY Coupler Standard supergrip coupler to suit most grease nipples and grease guns KY Coupler KY 9

10 Greasing Equipment Accessories KND 90º Needlepoint Coupler Ideal where access to the grease nipple is minimal 90º Needlepoint Coupler KDN KZE Concave Nipple Coupler For use on special nipples or in some cases where nipples have been damaged Concave Nipple Coupler KZE KZHY Hyperdermic Needlepoint Coupler Ideal for use on bearings fi tted with rubber dust covers. Length 130mm Hyperdermic Needlepoint Coupler KZHY Extended Needlepoint Couplers Ideal for hard to reach applications 45º Needlepoint Coupler KZLN45 90º Needlepoint Coupler KZLNR Hook Needlepoint Coupler KZLNJ Push On Extension For Air Equipment Push On flexible extension for air operated equipment Push On Extension 330mm Push On Extension 530mm PDF13 PDF21 Push On Flexible Extension For Manual Equipment Push On Flexible Extension with nipple to fi t KY coupler 330mm Push On Flexible Extension 530mm Push On Flexible Extension KDF13 KDF21 Oil / Grease Trolleys Ideal for transporting large Oil / Grease containers Trolley to suit 15 & 25 Litre Oil, 12.5 & 22kg Grease Drums Trolley to suit 50 & 60 Litre Oil, 50 & 55kg Grease Drums TR5 TR6 10

11 Greasing Equipment Accessories Aviation Greasing Kit Accessories typically required when lubricating aircraft Contains the following KDN, KDS, KDE8, KDF21, KY, KZDXL, KZHY, KZLNJ, KZLNS, KZLNR, KZLN45, KZSNR and J65 Aviation Greasing Kit ACK2 11

12 Fuel Transfer Pumps Hand Operated Litre-Stroke Fuel Transfer Pump The HP Litre-Stroke has an easy lever action and is designed for either 60 or 205 Litre drums. The pump is built for very harsh working conditions Features Pumps Diesel, Petrol, Kerosene and Lubricating Oils up to SAE 30 Supplied with a 2.4 metre anti-static rubber delivery hose and nozzle, and 1 metre two piece threaded suction tube Lockable handle and built-in nozzle holder 50mm bung adaptor Specifi cation Output: up to 40 litres per min. or 1 litre per stroke Litre-Stroke Fuel Transfer Pump HP 12

13 Fuel Transfer Pumps Electrically Operated Diesel Distributor - 230V ON / OFF switch Built in fi lter and bypass valve 4 metre delivery hose and nozzle 1" BSP ports IP55 WARNING: Do not use the pump for gasoline (petrol) transfer VOLTAGE FLOW RATE WEIGHT 230V 60 litres per min. 20.5Kg (pump unit) AF V 100 litres per min. 20.5Kg (pump unit) AF30100 Self Priming Fuel Transfer Kits Diesel oil transfer pump, available in 12V or 24V With handle and switch Fused 2 metre battery cable with clips 4 metre delivery hose and nozzle 3/4" BSP ports IP55 WARNING: Do not use the pump for gasoline (petrol) transfer VOLTAGE FLOW RATE WEIGHT 12V 40 litres per min. 6.8Kg LT V 40 litres per min. 6.8Kg LT Self Priming Fuel Transfer Pumps Diesel oil transfer pump, available in 12V or 24V With handle and switch Fused 2 metre battery cable with clips 3/4" BSP ports IP55 WARNING: Do not use the pump for gasoline (petrol) transfer VOLTAGE FLOW RATE WEIGHT 12V 40 litres per min. 3.6Kg DC V 40 litres per min. 3.6Kg DC

14 Fuel Transfer Pumps Electrically Operated Big Vane Pump - 12V & 24V Self-priming, motor-driven rotary vane pump with by-pass valve incorporated in the pump body. The stainless steel fi lter is incorporated in the pump body. Available with either 12V or 24V enclosed DC motor. Motor protection IP 55 grade. It is used in intermittent service with 30 minutes working cycles. Supplied with pump attachment support bracket. 1" ports for connection WARNING: Do not use the pump for gasoline (petrol) transfer. Complete Version: Pump supplied in metal casing, switch, 2 metre battery cable with crocodile clips and fuse VOLTAGE AMPS WATT RPM FLOW RATE WEIGHT DIMENSIONS 12V 35 Amps litres per min. 10Kg 300 x 190 x 250mm PB V 25 Amps litres per min. 10Kg 300 x 190 x 250mm PB12460 Fuel Transfer Barrel Kits - 12V & 24V Diesel Oil transfer kit, comprising of 12V or 24V electric pump, with plastic housing On/ Off switch, aluminium nozzle with brass swivel 1"F, 4 meters of rubber hose Ø 19mm with brass connections, metal telescopic suction tube, ring nut, suction fi lter and hose tails. 3/4" ports for connection WARNING: Do not use the pump for gasoline (petrol) transfer. VOLTAGE AMPS WATT RPM FLOW RATE WEIGHT DIMENSIONS 12V 20 Amps litres per min. 8Kg 550 x 360 x 170mm PTP V 15 Amps litres per min. 8Kg 550 x 360 x 170mm PTP2442 Self-Priming Vane Pump - 230V Self-priming, rotary electric vane pumps for the transfer of diesel oil. They are equipped with self ventilating induction motor with IP55 protection, class F insulation with terminal cut-out at 160º located in the winding. By-pass valve is integrated into pump body. The pump casting is in cast-iron, treated against corrosion and paint finished. The pump rotor is in sintered steel, the stainless steel filter is incorporated in the pump body. WARNING: Do not use the pump for gasoline (petrol) transfer. VOLTAGE AMPS WATT RPM FLOW RATE WEIGHT DIMENSIONS 230V litres per min. 8Kg 300 x 200 x 250mm HE60 230V litres per min. 15.4Kg 300 x 200 x 250mm HE

15 Oil Transfer Pumps Hand Operated Oil Change Kit Suitable for lawnmowers and other 4 stroke engines. Contains: 1 litre waste oil container 0.3 litre oil extraction pump Funnel Oil exchange kit FGP Oil Extractor Tank Ideally suited for extracting or exchanging engine oil or lubricants in: Motor Vehicles Motor Bikes Marine Engines Stationary Engines Non lubricant such as water from fish tanks etc. Manual Power Oil Extractor Tank FGP R-Series Ratio Oil Pumps The R100 is a 1:1 heavy duty oil pump designed to transfer oils up to 10 metres, R100S Features Suitable for oils up to SAE 140, automatic transmission fl uid, diesel kerosene, anti-freeze/anti-boil Designed to fi t from 60 to 205 litre drums 2" Bung adaptor and oil lubricator supplied Specifi cation Pump Ratio: 1:1 (Oil pressure is the same as air pressure) Output: 60 l/min of SAE 10 oil at 690 kpa (100 psi) air pressure (free fl ow) Suction Tube Length: R100S 210 mm Maximum Air Pressure: 1030 kpa (150 psi, 10.3 bar) Minimum Air Pressure: 400 kpa (60 psi, 4 bar) Minimum Air Compressor: 0.22m³/min (8 cfm) Air Inlet: 1/4" NPT Female Pump Outlet: 3/4" BSP or NPT Female Foot Valve Inlet: 1" BSP or NPT Female (Stub only) R100-Series - Stub pump R100S 15

16 Oil Transfer Pumps Air Operated R300S R-Series Ratio Oil Pumps The R300 is a 3:1 heavy duty oil pump designed to transfer oils up to 30 metres Features Suitable for oils up to SAE 140, automatic transmission fl uid, diesel kerosene, anti-freeze/anti-boil Designed to fi t from 60 to 205 litre drums 2" Bung adaptor and oil lubricator supplied The R300S can easily be wall mounted Specifi cation Pump Ratio: 3:1 (Oil pressure is 3 times air pressure) Output: 23 l/min of SAE 10 oil at 690 kpa (100 psi) air pressure (free fl ow) Suction Tube Length: R300S 210 mm Maximum Air Pressure: 1030 kpa (150 psi, 10.3 bar) Minimum Air Pressure: 400 kpa (60 psi, 4 bar) Minimum Air Compressor: 0.16m³/min (6 cfm) Air Inlet: 1/4" NPT Female Pump Outlet: 3/4" BSP or NPT Female Foot Valve Inlet: 3/4" BSP or NPT Female (Stub only) R300-Series - Stub pump R300S 16

17 Fuel & Oil Accessories Meters Mechanical Flow Meter The Z98 fl ow meter has been designed for use with thin viscosity fuels only such as diesel oil, gasoline and lubricating oils. It should not be used for resale purposes. Using mechanical gears, this meter translates fl ow data from a nutating disc into calibrated units which are registered on the face of the meter. Z98 is equipped with a 3 digit re-sett able batch register complete with marked tenths as well as a 6 digit maximum cumulative total. Available with litre units or gallon units. It is fi tted with a calibration screw for the adjustment of different liquids. Suitable for use with pump system. Mechanical fl ow meter SPECIFICATIONS Unit of measure Litres Flow rate (min-max) Type Nutating Disc Batch total 999 Cumulative total Working pressure Max 3.5 bar Accuracy +/- 1% Repeatability +/- 0.2% Connections 1" G Housing Material Aluminium Weight 1.8Kg Z98B Mechanical Flow Meter The Z98 fl ow meter has been designed for use with thin viscosity fuels only such as diesel oil, gasoline and lubricating oils. It should not be used for resale purposes. Using mechanical gears, this meter translates fl ow data from a nutating disc into calibrated units which are registered on the face of the meter. Z98 is equipped with a 3 digit resettable batch register complete with marked tenths as well as a 6 digit maximum cumulative total. Available with litre units or gallon units. It is fi tted with a calibration screw for the adjustment of different liquids. Suitable for use with pump or gravity feed system. Mechanical fl ow meter SPECIFICATIONS Unit of measure Litres Flow rate (min-max) Type Nutating Disc Batch total 999 Cumulative total Working pressure Max 3.5 bar Accuracy +/- 1% Repeatability +/- 0.2% Connections 1" G Housing Material Aluminium Weight 1.8Kg ILG00S 17

18 Fuel & Oil Accessories Pump & Filter Kits / Delivery Hoses DC Pump & Filter Kits Includes: Pump (40lpm pump, 45/60lpm available on request) CIM-TEK 10micron Hydrosorb filter Fittings Tank Dryer Y Strainer 40lpm 12V DC pump and fi lter kit 40lpm 24V DC pump and fi lter kit PFK005 PFK006 AC Distributor Unit & Filter Kits Includes: Distributor Unit with delivery hose and nozzle (Available with 60 or 100lpm pump) CIM-TEK 10micron Hydrosorb filter Fittings Tank Dryer Y Strainer 60lpm AC Distributor unit and fi lter kit 100lpm AC Distributor unit and fi lter kit PFK003 PFK004 AC Pump & Filter Kits Includes: Pump (Available with 60 or 100lpm pump) CIM-TEK 10micron Hydrosorb filter Fittings Tank Dryer Y Strainer 60lpm AC pump and fi lter kit 100lpm AC pump and fi lter kit PFK001 PFK002 Diesel Delivery Hoses to suit Pump & Filter Kits 3 metre 1" delivery hose to suit AC units (1" BSP x 1" BSP) DDH13 4 metre 1" delivery hose to suit AC units (1" BSP x 1" BSP) DDH14 6 metre 1" delivery hose to suit AC units (1 BSP x 1 BSP) DDH16 8 metre 1" delivery hose to suit AC units (1 BSP x 1 BSP) DDH18 4 metre 3/4" delivery hose to suit DC units (1" BSP x 3/4" BSP) DDH344 6 metre 3/4" delivery hose to suit DC units (1" BSP x 3/4" BSP) DDH346 Diesel Oil Hose Temperature Range: Description: Applicatio: I.D mm -40ºC to +80ºC Synthetic rubber, black, smooth, antistatic, oil resistant. Reinforcement: Textile spiral construction. Oil and weather resistant Transfer of diesel oil O.D. WEIGHT WORKING BURSTING ROLL mm PER METER PRESSURE PRESSURE LENGTH g 10 bar 30 bar 50 DIESEL g 10 bar 30 bar 50 DIESEL25 D DIESEL OIL 18

19 Fuel & Oil Accessories Gravity Feed Fuel Kits / Nozzles Gravity Feed Fuel Kits Diesel Hose Aluminium Nozzle Power Crimped Hose Ends Complete with Lever Valve & Fittings 3 Mtr 1" BSP Gravity Feed Fuel Kit TOG Mtr 1" BSP Gravity Feed Fuel Kit TOG Mtr 1" BSP Gravity Feed Fuel Kit with premium rubber hose TOG1011A 5 Mtr 1" BSP Gravity Feed Fuel Kit TOG Mtr 1" BSP Gravity Feed Fuel Kit TOG1021 Any Length made to order, please ask Sales Staff for further details. Manual Aluminium Nozzle Flow: Max 60 lpm Inlet: 1" BSP/G Outlet: Ø25 Swivel: Yes Max Pressure: 3.5 bar Manual aluminium nozzle with 1" inlet TOPGUN Aluminium Nozzle - with Automatic Shut Off Not suitable for Gravity Flow Systems This nozzle is designed for today s consumers needs. Small, trim, light weight, easy and convenient to operate. Flow: Max 60 lpm Inlet: 1 BSP/G Outlet: 15/16" Swivel: Yes Aluminium Nozzle with Automatic Shut Off TOG1038 Aluminium Nozzle - with Automatic Shut Off Not suitable for Gravity Flow Systems This nozzle can be used for the following applications: Heavy-Duty, High flow Truck Stop, Bus and Fleet Service Flow: Max 120 lpm Inlet: 1 BSP/T Outlet: 1 3/16 Swivel: Yes Aluminium Nozzle with Automatic Shut Off TOG1040 Brass Swivel for use with Nozzles MALE END FEMALE END 3/4" BSP 1" BSP MEC " BSP 1" BSP MEC

20 Fuel & Oil Accessories Filters / Strainers / Drumtap / Swivels Goldenrod Water Block Filter Assembly Water Block removes dirt and water from Gasoline and Diesel 17 Micron Filtration Suitable for 5 GPM Gravity Flow with 24 Head Water absorbing polymers trap water and restrict fuel fl ow The element needs to be replaced when fl ow becomes too slow 1" BSP Ports Filter Assembly with Paper Element - Water Absorbing TOG50W496 Replacement Elements to suit Tank Filter Paper Element - Water Absorbing Stainless Steel Element TOG50496 TOG50015 Replacement Bowl to suit Goldenrod Filter Assembly Spare bowl c/w seal to suit Goledrod Filter Assembly TOG50BOWL Filter Wrench to suit Goldenrod Assembly Goldenrod Filter Wrench TOG50491 Intake Strainer with Hose Tail TAIL TO SUIT HOSE ID 19mm (3/4") FLT20 25mm (1") FLT25 Brass Footvalve c/w Strainer FEMALE THREAD 1" BSP BFV1 Brass "Y" Intake Strainer THREAD BSP MESH 1/2" Female 400 micron YS12 3/4" Female 400 micron YS34 1" Female 400 micron YS1 Drumtap Drumtap with 3/4" Thread TOG

21 Fuel & Oil Accessories Water Absorbing Tank Filters HydroSorb Filters - Water Absorbing Tank Filter Cim-Tek Filtration, Illinois are the world leader in fuel fi lter technology. They offer the ideal solution to ULSD Diesel fi ltration with the patented HydroSorb range of fi lters for particle and water removal. HydroSorb has a high particle and water holding capacity which results in cleaner fuel. Available in 10 or 30micron rating. Please use the following listings to help you choose the most suitable fi lter for your needs. HydroSorb 450 / 475 Series Filter - 10 & 30 Micron / 120 lpm Application: General fuelling Dimensions: 8" x 3 3/4" Thread: 1 1/2" - 16 UNF Removes Water and Dirt from fuel 10 Micron fi lter suitable for Pumped fuel up to 95 lpm 30 Micron fi lter suitable for Gravity Feed or Pumped fuel up to 120 lpm ULSD Compatible Filter head: 1" BSP Ports FLOW FILTRATION Cim Tek Hydrosorb fi lter 95 lpm 10 microns CT70075 Cim Tek Hydrosorb fi lter 95 lpm 30 microns CT70076 Cim Tek Hydrosorb fi lter 120 lpm 30 microns CT70043 Filter head with 1" BSP ports to suit CT70075 and CT70076 CT50034 HydroSorb 400 Series Filter - 10 & 30 Micron / 95 lpm Application: General fuelling. Short fi lter for where space is limited Dimensions: 5 1/2" x 3 3/4" Thread: 1 1/2" - 16 UNF Removes Water and Dirt from fuel 10 Micron fi lter suitable for Pumped fuel up to 95 lpm 30 Micron fi lter suitable for Gravity Feed or Pumped fuel up to 95 lpm ULSD Compatible Filter head: 1" BSP Ports FLOW FILTRATION Cim Tek Hydrosorb fi lter 95 lpm 10 microns CT70060 Cim Tek Hydrosorb fi lter 95 lpm 30 microns CT70065 Filter head with 1" BSP ports to suit CT70060 and CT70065 CT50034 HydroSorb 800 Series Filter - 10 Micron / 150 lpm Application: High volume commercial systems Dimensions: 11" x 5" Thread: 1 1/2" - 16 UNF Removes Water and Dirt from fuel 10 Microns Suitable for Pumped fuel up to150 lpm (Not suitable for Gravity Feed) ULSD Compatible Filter head: 1" & 1 1/2" BSP Ports FLOW FILTRATION Cim Tek Hydrosorb fi lter 150 lpm 10 microns CT70063 Filter head with 1" BSP ports to suit CT70063 CT50105 Filter head with 1 1/2" BSP ports to suit CT70063 CT

22 Fuel & Oil Accessories Water Absorbing Tank Filters / Particle Filters Old Series HydroSorb 260 GRAVITY FLOW Series Filter - 30 Micron Replacement filter only available. Filter head no longer available. For NEW Gravity Flow installations use 400/450 Series 30 micron filter and head Dimensions: 8 1/2" x 3 3/4" Thread: 1 3/8" - 12 UNF Removes Water and Dirt from fuel 30 Microns Suitable for Gravity Flow and Pumped fuel up to 65 lpm ULSD Compatible Filter head: 1" BSP Ports FLOW FILTRATION Old type - Cim Tek Hydrosorb fi lter 65 lpm 30 microns CT70066 HydroSorb 260 Series Filter - 10 & 30 Micron / 65 lpm Application: General fuelling. Old series fi lter and head replaced by 450 series Dimensions: 8 1/2" x 3 3/4" Thread: 1" - 12 UNF Removes Water and Dirt from fuel 10 or 30 Microns Suitable for Pumped fuel up to 65 lpm ULSD Compatible Filter head: 1" BSP Ports FLOW FILTRATION Old type - Cim Tek Hydrosorb fi lter 65 lpm 10 microns CT70062 Filter head with 1" BSP ports to suit CT70062 CT50009 ULTRA FINE Particle Only Filtration 400 Series Particle Filter - 2 Micron / 95 lpm Application: For systems that require Ultra Fine Filtration Dimensions: 5 1/2" x 3 3/4" Thread: 1 1/2" - 16 UNF Removes Dirt from fuel 2 Microns Suitable for Pumped fuel up to 95 lpm ULSD Compatible Filter head: 1 BSP Ports FLOW FILTRATION Cim Tek Particle filter 95 lpm 2 microns CT70808 Filter head with 1" BSP ports to suit CT70808 CT Series Particle Filter - 2 Micron / 95 lpm Application: For systems that require Ultra Fine Filtration Dimensions: 8" x 3 3/4" Thread: 1 1/2" - 16 UNF Removes Dirt from fuel 2 Microns Suitable for Pumped fuel up to 95 lpm ULSD Compatible Filter head: 1 BSP Ports FLOW FILTRATION Cim Tek Particle filter 95 lpm 2 microns CT70810 Filter head with 1" BSP ports to suit CT70808 CT

23 Fuel & Oil Accessories Tank Dryer Tank Dryer - Water Absorbing Polymer Cim-Tek has developed a water absorbing product called the Tank Dryer for use with fuel storage tanks. The Tank Dryer contains a proprietary super-absorbent polymer that absorbs free water at the bottom of tanks containing diesel, bio diesel and fuel oil. It is easy to use, inexpensive, and helps to prevent downtime caused by water contamination. Take care of the problem before it starts... use Cim-Tek Tank Dryer. Cim-Tek Tank Dryer CT

24 Fuel & Oil Accessories Hosetails / Fittings Brass BSP Hosetail MALE THREAD TAIL TO SUIT HOSE ID 3/4" BSP 3/4" BRASSRC3419 3/4" BSP 1" BRASSRC3425 1" BSP 3/4" BRASSRC1019 1" BSP 1" BRASSRC1025 Male / Male GB Nipple MALE THREAD MALE THREAD SELF COLOUR 1/4" 1/4" TOG1078 1/2" 1/2" TOG1079 3/4" 3/4" TOG1075 3/4" 1" TOG " 1" TOG /2" 1 1/2" GB280 2" 2" GB2 3" 3" GB3 Male / Male GB Tube MALE THREAD MALE THREAD TUBE LENGTH GALVANISED 3/8" 3/8" 200mm FG " 1" 80mm FG23180 Male Plug MALE THREAD SELF COLOUR GALVANISED 1/8" - FG " - FG /2" GB " - FG2902L 4" Female Cap MALE THREAD SELF COLOUR 1" TOG1071 3" TOG

25 Fuel & Oil Accessories Fittings Female / Female GB Socket FEMALE THREAD FEMALE THREAD SELF COLOUR 1/2" 1/2" TOG1074 1" 1" TOG /4" 1 1/4" TOG /2" 1 1/2" TOG1083 2" 2" FG162 4" 4" Female GB Tee THREADS 1 & 2 THREAD 3 SELF COLOUR GALVANISED 3/8" 3/8" - FG /2" 1/2" - FG /2" 3/4" TOG1076-1" 1/2" - FG130112SBX 1" 1" - FG /2" 1/2" GB112T GB112TGALV 2" 1/2" GB2T12-2 1/2" 2 1/2" - FG Female / Male GB Reducer FEMALE THREAD MALE THREAD GALVANISED 3/8" 1/2" FG /2" 1" FG Female / Male GB Socket 3 Piece FEMALE THREAD MALE THREAD GALVANISED 2 1/2" 2 1/2" FG

26 Fuel & Oil Accessories Fittings Female GB Cross FEMALE THREAD FEMALE THREAD GALVANISED 1" 1" FG1801 Female / Female 90º GB Elbow FEMALE THREAD FEMALE THREAD GALVANISED 1/2" 1/2" TOG1073 3/4" 3/4" TOG9034 Female / Female 90º GB Elbow c/w Inlet Port FEMALE THREAD FEMALE THREAD INLET PORT SELF COLOUR 1 1/2" 1 1/2" 1/2" GB130R 2" 2" 1/2" GB2R12 Female / Male 90º GB Elbow MALE THREAD FEMALE THREAD GALVANISED 1" 1" TOG1069A 90º GB Elbow SIZE GALVANISED 2 3/8" FG

27 Fuel & Oil Accessories Shut Off Valves Gate Type Shut Off Valve PORT SIZE 3/8" BSP SOV38 1/2" BSP SOV12 3/4" BSP SOV34 1" BSP SOV1 1 1/4" BSP SOV /2" BSP SOV112 2" BSP SOV2 3" BSP SOV3 4" BSP SOV4 Lockable Gate Type Shut Off Valve PORT SIZE 1" BSP SOV1LGV Ball Lock Lever Type Shut Off Valve (Female/Female) Temperature continual from -20 C to +120 C. PORT SIZE 1/4" BSP LTVFF14 3/8" BSP LTVFF38 1/2" BSP LTVFF12 3/4" BSP LTVFF34 1" BSP LTVFF1 1 1/4" BSP LTVFF /2" BSP LTVFF112 2" BSP LTVFF2 2 1/2" BSP LTVFF212 3" BSP LTVFF3 4" BSP LTVFF4 Ball Lock Lever Type Shut Off Valve (Male/Female) Temperature continual from -20 C to +120 C. PORT SIZE 1/4" BSP LTVMF14 3/8" BSP LTVMF38 1/2" BSP LTVMF12 3/4" BSP LTVMF34 1" BSP LTVMF1 1 1/4" BSP LTVMF /2" BSP LTVMF112 2" BSP LTVMF2 2 1/2" BSP LTVMF

28 Urea - Ad Blue Nozzles Urea - Ad Blue Nozzle Suitable for use with Urea Ad Blue / Water Light weight design with lever lock Flow: Max 60 lpm Inlet: 19mm hosetail Urea Ad Blue nozzle with 19mm hosetail TOGAB

29 Consumables Threadlocking 243 Threadlocking Adhesive - Medium Strength This general purpose threadlocker secures and seal bolts, nuts and studs up to size M36 to prevent loosening due to vibration on moving assemblies (e.g. pumps, gear boxes, presses) and allows disassembly with normal tools. Effective on all metals, including passive substrates such as stainless steel, aluminium and plated surfaces. It is proven to be tolerant of minor contamination such as oils and cutting fl uids. Fixture time: Steel 10 min. / Brass 5 min. Temperature range: -55 C to +180 C Breakaway torque: 26 Nm 12 x 24ml Blister card ml Bottle Threadlocking Adhesive - Medium Strength This medium threadlocker secures and seal bolts, nuts and studs up to size M36. Prevents loosening on vibrating assemblies (e.g. pumps, gear boxes, presses) and allows disassembly with normal tools. Effective on all metals and is tolerant of minor contamination such as oils and cutting fl uids. It s key differentiator is the White Material Safety Data Sheet. LOCTITE 2400 carries no hazard symbols, risk or safety phrases and does not contain any declarable carcinogens, mutagens or reproductive toxins. Fixture time: Steel 10 min. / Brass 8 min. Temperature range: -55 C to +150 C Breakaway torque: 20 Nm 12 x 5ml Blister card Threadlocking Adhesive - High Strength This high strength, high viscosity threadlocker secures and seal bolts, nuts and studs up to size M80. The product cures when confi ned in the absence of air between close fi tting metal surfaces and prevents loosening and leakage from shock and vibration. Fixture time: Steel 15 min. / Brass 7 min. / Stainless Steel 180 min. Temperature range: -55 C to +150 C Breakaway torque: 25 Nm 50ml Bottle Threadlocking Adhesive - Permanent Locking This high-strength threadlocker serves to permanently lock and seal bolts, nuts and studs which must not come loose up to size M20. To prevent loosening due to vibration, it acts with maximum effi cacy on all metals and is tolerant of minor contamination such as oils and cutting fl uids. Can be disassembled by heating to 300 C. Fixture time: Steel 10 min. / Brass 10 min. / Stainless Steel 150 min. Temperature range: -55 C to +180 C Breakaway torque: 33 Nm 12 x 10ml Bottle ml Bottle x 24ml Blister card Threadlocking Adhesive - Permanent Locking Like LOCTITE 270 this high-strength threadlocker serves to permanently lock and seal bolts, nuts and studs, up to size M20 and prevents loosening due to vibration. It acts with maximum effi cacy on all metals and is tolerant of minor contamination such as oils and cutting fl uids. It s key differentiator is the White Material Safety Data Sheet. It carries no hazard symbols, risk or safety phrases and does not contain any declarable carcinogens, mutagens or reproductive toxin. Can be disassembled by heating to 300 C. Fixture time: Steel 5 min. / Brass 4 min. / Stainless Steel 5 min. Temperature range: -55 C to +150 C Breakaway torque: 20 Nm 12 x 5ml Blister card

30 Consumables Pipe & Thread Sealing 55 Pipe Sealing Cord Loctite 55 threaded pipe and fi tting sealant needs no cure time and results in an immediate full pressure sealing. It is wound straight from the dispensing package onto the threads of the pipes. Recommended for sealing metal and plastic tapered pipe threads and fi ttings up to 4" NPT (National Pipe Thread) for use in industrial applications in aqueous and non-aqueous fl uids. Certifi ed to NSF/ANSI, Standard 61, with approval for gas and potable water. Temperature range: -55 to +130 C 150 metre Container Hydraulic/Pneumatic Thread Sealant This medium strength, fast curing product is designed for the locking and sealing of metal only pipe fi ttings and other cylindrical metal assemblies. Recommended for fi ne thread fi ttings as used in Hydraulic and Pneumatic insulation and small general fi ttings up to size M26. Temperature range: -55 to +150 C Breakaway torque: 15 Nm 50ml Bottle Slow Cure Thread Sealant Loctite 572 is designed for the locking and sealing of metal pipe fi ttings. Recommended for all coarse metal threads up to 3" where slow cure is required for adjusting of valves and fi ttings Temperature range: -50 C to +150 C Breakaway torque: 7 Nm 50ml Bottle Slow Cure Thread Sealant - Medium Strength Loctite 577 is designed for the locking and sealing of metal only threaded pipes and fi ttings up to size M80. Particularly suitable for overhead and fast application at low temperatures as it provides an instant, low-pressure seal and offers less migration of liquid product after application. Resistant to Fuel, Oil, Coolants and Hydraulic Fluids Temperature range: -55 C to +150 C Breakaway torque: 11 Nm 50ml Bottle

31 Consumables Gasketing 510 High Temperature Flange Sealant Loctite 510 is a high temperature resistant anaerobic general gasketing product, which cures when confi ned in the absence of air. Ideal for use on rigid metal fl anges or where high temperature and chemical resistance is needed. It ensures an instant, lowpressure seal, adapts to surface irregularities and increases the torque capacity. Fixture time: Steel 25 min. / Aluminium 45 min. Temperature range: -55 C to +200 C 50ml Tube Flexible Medium Cure Loctite 515 seals close fi tting joints between rigid metal faces and fl anges and will fl ex with minor fl ange movement. Provides resistance to low pressure immediately after assembly of fl anges. Typically used as a form-in-place gasket for pumps, thermostats, compressors, transmission housings and axle covers Fixture time: Steel 30 min. / Aluminium 30 min. Temperature range: -55 C to +150 C 50ml Tube Multi Gasket Loctite 574 seals close fi tting joints between rigid metal faces and fl anges. Provides resistance to low pressure immediately after assembly of fl anges. Typically used as a form-in-place gasket on rigid fl anged connections, e.g. gearbox and engine casings etc. It has a high oil tolerance and excellent water and glycol resistance. Fixture time: Steel 15 min. / Aluminium 45 min. Temperature range: -55 C to +150 C 50ml Bottle Gasket Maker / Sealant This black silicone fl ange sealant has excellent adhesive strength and cures to a permanently fl exible, reliable and long lasting gasket. The product can also replace cut gaskets. Meets major automotive manufacturer specifi cations. Instant sealing performance up to 0.25mm at 0.35 bar. Ideal for gearboxes, thermostat housings, pumps, timing gear covers and oil sumps and for applications involving large gaps like stamped sheet metal covers where good oil resistance and the ability to withstand high joint movement is required. The unique even-flow nozzle on the Quick Gasket Dispenser is very easy to use and allows dispensing with extra accuracy. Skin over time: 30 min. Temperature range: -55 C to +200 C 6 x 200ml Quick Gasket Dispenser x 100ml Tube

32 Consumables Gasketing / Retaining 595 Silicone Sealant Designed for superior bonding and sealing to most surfaces like glass, metal, ceramics, composites and most plastics (not recommended for concrete). This product resists ageing, weathering and thermal cycling without hardening, shrinking or cracking. Ideal for components subjected to shock, constant vibration, twisting, fl exing, thermal expansion and contraction The thixotropic nature of Loctite 595 reduces the migration of liquid product after application to the substrate. Skin over time: 10 to 15 min. Temperature range: -55 C to +250 C 12 x 310ml Tube Clear Silicone Sealant x 310ml Tube Black Silicone Sealant Flange Sealant Loctite 5922 is a black, viscous paste for sealing/dressing old and new pre-cut gaskets (paper, cork, felt, etc.). It is a slow drying, fl exible setting paste that changes to a pliable, non-hardened fi lm through solvent evaporation. It seals fl anges, fi ttings, connections and fl exible assemblies against leakage. It increases the reliability of gasket seals. It is suitable for valve cover gaskets, oil pan gaskets, cover plates, threaded connections and hose connections and is ideal for part assembly after repairs. Temperature range: -54 C to +204 C 12 x 60ml Blister Card Instant Gasket Loctite 5926 is a multi-purpose fl exible silicone sealant. Ideal for use on machined, painted or cast surfaces, metal or plastic. It cures on exposure to moisture in the air to form a tough rubber gasket. This product resists ageing, weathering and thermal cycling without hardening, shrinking or cracking. Suitable on valve covers, timing gear covers, differential covers, oil pans, transmission pans, water pumps, and thermostat housings. Skin over time: 60 min. Temperature range: -55 C to +200 C 12 x 40ml Blister Card ml Tube Retaining Compound - Medium Strength Designed for the bonding of cylindrical fi tting parts, particularly where disassembly is required for servicing operations. The product cures when confi ned in the absence of air between close-fi tting metal surfaces and prevents loosening and leakage due to shock and vibration. Ideal for parts that need subsequent dismantling, i.e. retention of bearings on shafts and in housings. Temperature range: -55 C to +150 C 641 Medium Strength retaining compound - 50ml Bottle Retaining Compound - High Strength This product is designed for the bonding of cylindrical fi tting parts. It exhibits robust curing and offers high temperature performance and good oil tolerance. High strength on all metals, including passive substrates (e.g. stainless steel) and is ideal for retention of parts with a clearance or interference fi t up to gap size 0.15mm and high-strength assemblies. Typical applications are the retaining of splined shafts, bearings, gearings and steering system components. Can be disassembled by heating to 300 C Temperature range: -55 C to +180 C 648 High Strength retaining compound - 50ml Bottle

33 Consumables Retaining / Structural Bonding Super Glue High performance formula gives a strong bond in seconds. Ideal for bonding china, porcelain, most plastics, paper, card, metal, rubber, wood, leather and many other different materials. Dries transparent for invisible bonds, is solvent-free and water and dishwasher resistant. There is a self-piercing & anti-clog cap and the Precision bottle has an extra long nozzle that is ideal for diffi cult repair jobs. Super Glue - Universal 24 x 3g Blister Card Super Glue - Precision 24 x 5g Blister Card Terostat 9220 Power Adhesive Terostat 9220 is a solvent and isocyanate-free MS polymer with excellent adhesive and sealing properties for bonding many different materials, such as stainless steel, aluminum and other metals, plastics, wood and painted surfaces. Also demonstrates good UV resistance and is Saltwater Resistant. It is suitable for bonding metal to metal, plastics (except PP, PE) and wood. eg spoilers and body repairs. Skin over time: 15 min Temperature range: -40 C to +100 C 310ml Cartridge Rear View Mirror Bonder Kit for bonding metal rear-view mirror brackets to windscreen. Compensates for differential thermal expansion of parts and therefore also recommended for metal vent window handles and hinges. Can also be used for glass-to-metal joints on furniture etc. Ideal for glass mounted phone and radio aerials. 0.5ml Blister Card Terostat 8517H Glass Primer Primer for Direct Glazing Sealants. Terostat primer is used for adhesion improvement and UV protection. To be used if the glass has a ceramic printed border and where bare metal is exposed on the metal vehicle frame 12 x 25g Bottle

34 Consumables Flexible Sealing & Bonding Terostat 8597 HMLC Glazing Sealant A one component, moisture curing Direct Glazing Sealant used for windscreen replacement where a solid safety guarantee is required, with excellent sag resistance based on polyurethane, which cures by reacting with moisture to a soft elastic product. The skin formation and curing times are dependent on humidity and temperature and also depends on the joint depth. Safe drive-away time of 1 hour according to FMVSS and 4 hours according to to the most stringent European crash test standard. 12 x 310ml Cartridge Terostat PU92 Sealant A one component polyurethane black adhesive that cures by reacting with atmospheric moisture to give an elastic product. The product has good adhesion to many metals and plastics without primer. Used in vehicle body manufacture, railway carriages and boat building. High strength and therefore capable of partially or completely replacing screws, rivets & clips. Anti-vibration effect due to high elasticity. Over paintable, sandable and grindable. Suffi cient open time for large surface bonding, high sag resistance and can be spatula applied 12 x 310ml Cartridge

35 Consumables Anti-Seize / Lubrication 8040 Freeze & Release A special mineral oil formulation to free rusted, corroded and seized parts. The shockfreezing effect will cool parts instantly down to -43ºC and cause microscopic cracks in the layer of rust. This allows the lubricating ingredients to work directly into the rust by capillary action. Released parts remain lubricated and protected from corrosion Freeze & Release (8040) 12 x 400ml Freeze & Release (8040) 400ml With literally thousands of uses, WD-40 is the #1 multi-purpose problem solver. It cleans, protects, penetrates, lubricates and displaces moisture like no other product on earth. Aerosol Cans WD40-30 x 300 ml Aerosol Can - Smart Straw WD40300SS30 WD40-24 x 450 ml Aerosol Can - Smart Straw WD450SS24 WD40-12 x 600 ml Aerosol Can Bulk & Applicator WD40-5 litre container complete with spray applicator WD40 - Spray applicator (supplied empty) WD40-5 WD40-SPRAY 35

36 Consumables Cleaning 7850 Hand Cleaner with Pumice Hand cleaner for severely stained hands, e.g. after vehicle repair Contains extra-fine abrasives, which clean deep into pores. With jojoba, lanolin and aloe for added skin conditioning and protection Citrus extracts give a pleasant, fresh smell Works with or without water Tested for skin compatibility Biodegradable, free of mineral oils Hand Cleaner (7850) 1 x 3 litre Dispenser Hand Cleaner (7850) 4 x 3 litre Dispenser GORILLA Wipes Pre-impregnated cleaning wipes designed primarily for use by anyone who needs a fast and effective hand cleaning product. No further need for dirty wet towels, messy liquid cleaners or water. This is a true all round multi purpose cleaning solution for most types of stains and dirt. They clean general grime, oil & water based paints, instant grab adhesives, silicone & acrylic sealants, PU foam, oil, tar, grease, permanent marker, glues. They will remove most dirt and grime without effecting old paint 80 of 20cm x 30cm Gorilla Wipes GORILLA 7063 Cleaner and Degreaser Solvent-based, general-purpose product for cleaning and degreasing of surfaces. It evaporates quickly, leaves no residue and is non-corroding. Applications: Removes oil, grease and dirt. Ideal for use prior to adhesive bonding and sealing applications Aerosol Cleaner (7063) 400ml 7063 Blue Paper Towel 2 Layers Honeycombed surface 380 metre roll Blue paper towel 37cm x 380 metres PM

37 Consumables Cleaning / Oil Oil Spill Granules Technical Information: Absorbent Granules, ideal for cleaning up Oil Spillage Oil Absorption 51% Water Absorption 64% Calcium Carbonate and China Clay mix 30 Litre Bag of Spilkleen Plus Granules WH9002 Premium Quality Vacuum Pump Oil A specially blended premium quality vacuum pump oil suitable for all makes of vacuum pumps. Designed to give the maximum protection against wear and corrosion giving extended pump life and improved effi ciency. Inhibits oxidation Anti-foaming Protects against corrosion Excellent anti-wear properties SIZE Premium quality vacuum pump oil 5 Litre VPO005 Chainsaw Bar Oil Benefi ts: Highly effective adhesive additive guarantees economic use Good corrosion protection for all blank metal components Application: Modern, high-performance chain oil with special adhesive additive suitable for all brands of chainsaw Properties: Optimal full lubrication in summer and winter, including under more diffi cult usage conditions and for sawing hardwood Additives to improve lubrication guarantee extremely low wear of chain and rails No smoke generation, even under heavy loads SIZE Chainsaw bar oil cst. 5 Litre 34005GP 37

38 Consumables Body Fillers Plastic Padding - Chemical Metal The original "Chemical Metal" is a rock hard multi purpose repair paste. Use on metal, wood, stone, glass, concrete etc. and for joining dissimilar materials. Thousands of uses on the car, boat, farm, in industry and around the home. Suitable for fi lling, trowelling, joining and sealing and allows machining, including tapping threads, after 20 minutes. Working time is 5 min and cure time is 20 min. Resistant to temperatures up to +160 C 6 x 180ml Tin - chemical metal Plastic Padding - Glass Fibre Paste Bridges and fi lls big gaps/holes in one go. Contains glass fi bre strands for high tensile strength. Tack free fi nish allows easy removal of excess product. Finish with any plastic padding fi ller for a perfect repair 6 x 750g Tin Plastic Padding - Glass Fibre Filler A strong glass fi bre re-enforced fi ller for structural repairs and deep fi lling on glassfi bre. Impervious to water, it has a No-tack fi nish for easy sanding and fi nishing. Use for joining and sealing wood, fi breglass, steel and aluminium. It has a working time of 8 min, a curing time of 20 min and a maximum temperature resistance on steel of +160 C. 6 x 180ml Tin - plastic padding - glass fi bre fi ller Plastic Padding - Gelcoat Filler White Waterproof gelcoat fi nish. Repairs surface damage on glass fi bre hulls. Can be pigmented or painted with all marine paints and is easy to mix, apply, shape and sand. Use with Glass Fibre Matt for structural repair to GRP. It has a working time of 8 min and a curing time of 20 min. and can tolerate temperatures up to +160 C 12 x 165g Tube Plastic Padding - Mixing Board Reusable mixing board made from strong, durable, easy to clean polypropylene Plastic Applicator (100)

39 Consumables Body Fillers Plastic Padding - Super Steel Epoxy-Weld The amazing Epoxy weld for 1001 emergency repairs around the house, car, garden and boat. This product is a metal-fi lled, two-component adhesive which sets like steel and is suitable for metal, wood, china, stone, glass and leather. It hardens in 5 minutes and cures in 10 minutes and can tolerate temperatures up to +315 C. 12 x 50g Blister Card Extra Hardener For use with all Plastic Padding bodyfi llers and resin products (not gelcoat). 9 x 16g Tube

40 Consumables Rust Remedy / Cable Ties / Tape LOCTITE Rust Remedy (7503) Sandable Rust Converter is a single component rust treatment product for iron and steel, which dries at ambient temperature. The product is a synthetic latex in an aqueous solution, which converts rust (red) into a black stable complex and provides a protective coating to keep moisture and oxygen away from the surface. The dry coating is sandable, inhibits further corrosion and acts as a primer for subsequent painting with most known automotive paints Rust Remedy (7503) 12 x 90ml Cable Ties WIDTH LENGTH COLOUR Black CT25100B Orange CT25100ORA Violet CT25100VIO Black CT36140B Black CT36200B Blue CT36200BLU Green CT36200GRE White CT36200WHI Black CT48200B Blue CT48200BLU Green CT48200GRE Red CT48200RED Yellow CT48200YEL White CT48200WHI Black CT48300B White CT48300WHI Black CT48370B Black CT76300B Black CT76370B Black CT90430B Black CT90776B Insulating Tape Sold per Roll WIDTH ROLL LENGTH RED BLACK YELLOW Insulating tape 19mm 20 metres CIT20RED CIT20BLACK CIT20YELLOW 40

41 Clamps, Ties & Tape Tape Masking Tape Sold per ROLL COLOUR WIDTH ROLL LENGTH Masking tape Neutral 24mm 50 Metres Masking tape Neutral 36mm 50 Metres Masking tape Neutral 48mm 50 Metres Duck Tape COLOUR WIDTH ROLL LENGTH Duck tape - box of 6 Silver metres Duck tape - single roll Silver metres P.T.F.E Tape Sold per ROLL COLOUR WIDTH ROLL PART LENGTH NUMBER P.T.F.E Sealing tape White 12mm 12 metres FG1000 Safety Grip Tape - Black Sold per ROLL COLOUR WIDTH ROLL PART LENGTH NUMBER Safety grip tape Black 50mm 18.3 metres H3401 Silage Tape Note: Sold in carton of 24, part number is for a single roll WIDTH LENGTH Inch Yards 3" 20 Silage tape - black SILT

42 Tyre Care Tube Patches / Chemicure Strips & Tools REMA - TIP TOP Patches For the repair of Motorcycle, Car, Truck and Tractor Tyre Tubes You can use the table provided to fi nd a suitable patch for your application. PATCH SIZE Round Patches Oval Patches 7 7a 7b 7c Round Patches Tube Patches are sold per pack, 1 on an order will equal 1 pack SIZE QTY PER PACK No.1 Patch 35mm No.2 Patch 45mm No.3 Patch 54mm No.4 Patch 75mm No.5 Patch 94mm No.6 Patch 116mm Oval Patches Tube Patches are sold per pack, 1 on an order will equal 1 pack SIZE QTY PER PACK No.7 Patch 74 x 37mm No.7a Patch 90 x 45mm No.7b Patch 150 x 75mm No.7c Patch 188 x 94mm Chemicure Strips - for repairing Tubeless Tyres SIZE PACK QTY Tyre repair string 200 x 3.5mm Tyre repair string 300 x 3.5mm Tyre repair string 200 x 6.0mm A Needle for applying Chemicure Strips TYPE A Small straight needle for 3.5mm chemicure strips A Large straight needle for 3.5mm chemicure strips B 'T' Shaped needle for 6mm chemicure strips B 42

43 Tyre Care Repair Patches for Cross PLY Tyres Repair Patches for Cross-PLY Tyres - PN Series Repair patches for the durable repair of cross-ply tyres of any size in accordance with the applications shown in the chart below. DESIGNATION NUMBER SIZE OF UNIT IN OF PLIES THREAD DIRECTION PN mm PN mm PN mm PN mm PN mm PN mm Guide for Cars, Vans and Trucks C (MAX) PR mm Inch PLY RATING /8" PN Number /2" PN Number " PN Number /8" PN Number " PN Number " PN Number " PN Number " PN Number PN PN05S - 010S for Sidewalls 50% Guide for Tractors and Combines C (MAX) PR mm Inch PLY RATING " PN Number " PN Number " PN Number " PN Number " PN Number Guide for Forklifts and Heavy Duty Trailers C (MAX) PR mm Inch PLY RATING " PN Number " PN Number " PN Number

44 Tyre Care Repair Patches for Radial Tyres Repair Patches for Radial Tyres - RAD 100 Series Repair patches for the durable repair of Radial tyres of any size in accordance with the applications shown in the chart below. DESIGNATION NUMBER OF PLIES DIMENSIONS RAD 180TL x 150mm RAD 184TL x 215mm Non Repairable Area Car Van 2 Axle Truck 3 Axle Truck A R C C O A mm R mm A/C mm R mm CØ mm Max. RAD Max. Max Q TL TL T TL TL H TL V TL ZR 110 TL TL PR TL TL TL R R / - 255/ TL Cable 80 2 Cable TL TL TL TL TL R - 11R 125 TL / 235/ - 285/ 135 TL TL Cable 80 2 Cable TL 1 Cable Cable TL 3 Axle Truck 3 Axle Trailer Forklift Tractor R - 15 R 12/ - 13/ 295/ - 365/ R / - 385/ A mm R mm A/C mm R mm CØ mm Max. RAD Max. Max TL TL TL TL TL TL TL Cable Cable TL 1 Cable Cable TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL TL

45 Tyre Care Solvents / Buffers / Repair Kits Vulcanising Fluid For the vulcanisation of Tube patches, Rubber base valves and valve patches Vulcanising fl uid 10g Tube Vulcanising fl uid 25g Tube Vulcanising fl uid 175g tin complete with brush Liquid Buffer Liquid Buffer is a solvent used to remove Silicones, Talcs and other mould release agents from the inside of the tyre prior to mechanical buffi ng Liquid buffer 500 ml aerosol Special Cement BL Accelerator solution for the application of PN and RAD repair patches Special cement 350g Tin Repair Kits Cycle Outfi t TT-02 Outfi t TT-12 Outfi t TT-20 Outfi t TT-30 SUITABLE FOR Push Bikes Cars & Trucks Trucks Tractors CONTENTS 6 x F1 Patches 1 x F2 Patch 1 x Emery paper 1 x Valve 1 x 5g Tube Vulcanising Fluid 4 x No.1 Patches 2 x No.2 Patches 1 x No.3 Patch 1 x No.4 Patch 1 x No.7 Patch 1 x No.7a Patch 1 x Rasp 1 x 13g Tube Vulcanising Fluid 8 x No.1 Patches 2 x No.2 Patches 1 x No.3 Patch 1 x No.4 Patch 1 x No.5 Patch 1 x No.7 Patch 1 x No.7a Patch 1 x No.7b Patch 3 x Rasps 3 x Valve Cores 1 x 30g Tube Vulcanising Fluid 12 x No.1 Patches 6 x No.3 Patch 2 x No.4 Patch 1 x No.5 Patch 3 x No.7 Patch 4 x No.7a Patch 2 x No.7b Patch 2 x Tyre Repair Units (PN03) 1 x Rasp with wooden handle 2 x Spare Rasps 1 x Patch Stitcher 1 x 60g Tube Vulcanising Fluid

46 Tyre Care Valves / Valve Cores Snap in Valves to suit Tubeless Tyres LENGTH TO SUIT HOLE Valve TR Car Valve LENGTH BASE DIA Car valve TR Truck Valve LENGTH BASE DIA Truck valve TR75A Truck valve TR78A Air Water Valve For the repair of Air / Water type Tractor Tubes Air water valves TR218A Cranked Valve S/O Valve type TR1175A Valve Cores BOX QTY Box of 5 - Valve core - Long (Car / Truck) Valve core - Short (Car / Truck) Air / Water insert valve TR218 (for Standard. A.W. Valve) Air / Water insert valve TR218A (for New Fast Flow. A.W. Valve)

47 Tyre Care Valve Caps / Valve Tools / Tyre Levers Plastic Valve Cap Plastic cap (VC 8 eq) Valve Repair Tool 4 Way For the fi tting and removal of valve cores OUTER THREAD SIZE INNER THREAD SIZE VG 12 / VG 8 VG Valve Core Screwdriver Valve core screwdriver Tyre Levers LENGTH DIAMETER 30" 7/8" TTL3 LENGTH DIAMETER 34" 3/4" TTL1 LENGTH 19 1/2" TTL40 LENGTH 20" TTL

48 Tyre Care Tyre Repair Tools / Chalk / Airline Gauges Water - Filling / Emptying Tool Water - Filling / Emptying tool Hand Rasp 4.5mm - Small hand rasp mm - Large hand rasp Marking Chalk White marking chalk - Pack of AIRFORCE MK4 Airline Gauge The AIRFORCE MK4 Tyre Infl ator is a robust and highly accurate, offering leading infl ation and defl ation rates and high performance for both indoor and outdoor applications. The redesigned piston and seal arrangement means increased accuracy - cycle tests now give over 400,000 infl ation cycles at 100% accuracy Complies to: EC 86/217, EN12645:2014 Reading Accuracy: 0.1 bar / 2 psi Maximum Inlet Pressure: 13.8 bar / 200 psi Inflation Flow: 500 l/min / 18 cfm Operating Temperature: -25 to 55 C Airforce MK4 Airline Gauge Supplied in hang pack carton PCLGUN Air Inflator c/w Gauge Pressure Range: 0-10 Bar (0-140 PSI) Pistol grip infl ator c/w clip on connector & gauge

49 Tools Introduction Who are GRIP-ON? Grip-On manufacture the widest and most modern range of locking pliers & clamps in the world, continually producing top quality and innovative tools to meet the growing demands of automotive, maintenance and general welding professionals. Grip-On use the most sophisticated and up-to-date machinery and tooling, much of which is designed and produced in-house, to ensure maximum effi ciency and productivity. Having been accredited with the prestigious ISO 9001:2000, Grip-On s commitment to ensure the highest quality standards is total and unreserved. Listed below are some of the Features and Benefi ts of Grip-On Tools FEATURES Quality cold-rolled steel body and handles Smooth rounded edges Orange & Black epoxy paint fi nish BENEFITS Helps ensure years of service Comfortable handling without risk of injury 10 times more rust resistant than nickel or chrome. Greater spatter resistance Adjustable bolt with knurled head Locking nut Prevents slippage against oil and grease. Permits selection of size and required clamping pressure. Can be set to use the tool as a simple pliers Jaw opening can be secured at required position for repetitive jobs Locking Mechanism Leaves BOTH HANDS FREE when clamping Eliminates squeezing action and general hand fatigue when manipulating Tip of release lever projecting at end of handle Spring loaded release lever Quick NO-PINCH powerful releasing especially when tools are fi rmly locked Lever is always out of the way when handling Drop forged chrome vanadium jaws Ensures toughness and durability of tool Holes in mobile jaw are drilled and not punched to ensure they are cylindrical Large diameter of rivets Piano wire spring Ensures maximum bearing with the rivets (punch holes give poor bearing) Permits secure joints adding to the durability and robustness of the tool Ensures smooth and efficient opening of jaws 49

50 Tools Wrenches / Clamps Omnium Grip Locking Wrench Modern, multi-purpose design ideal for all trades, including welding, mechanics, plumbing, DIY, etc. The Jaw confi guration combining straight, curved and convex profi les. This versatile tool securely grips round, fl at & large objects. LENGTH CAPACITY 7" Omnium Grip 200mm 0-40mm GO7OR 10" Omnium Grip 235mm 0-60mm GO10OR 12" Omnium Grip 300mm 0-60mm GO12OR Curved Jaw Locking Wrench General purpose. Great capacity for use around the house, on the car, in the garage, workshop or factory. The narrow, large opening curved shaped jaws allows a fi rm hold on all round shapes. LENGTH CAPACITY 7" Curved Jaw 190mm 0-42mm GO7CR Long Nose Locking Wrench Provides aid when holding, placing or extracting pieces in awkward areas, engines, etc. The long slim jaw design enables pliers to reach deep into recessed areas and the curved section can hold rounded objects. LENGTH CAPACITY 6" Long Nose 165mm 0-55mm GO6LNR Sheet Metal Clamp Invaluable tool for sheet metal workers, metal fabricators and professionals involved with upholstery. The wide jaw profi le allows powerful grip on large thin surfaces. Great for bending, forming and crimping sheet metal without hand gripping effort. LENGTH CAPACITY 8" Sheet Metal Clamp 200mm 0-45mm GO8SMR 49a

51 Tools Clamps / Cutter Locking U-Clamp Holds two sections together with a fi rm grip. Hands Free solution in general welding and body repair work. The U-shaped jaw profi le permits the clamping of adjacent joints and allows perfect visibility when welding. LENGTH CAPACITY 9" Locking U-Clamp 200mm 0-60mm GO9UCR Chain Pipe Cutter Cuts thin wall pipes (stainless steel, copper, PVC, etc.) up to 2.6mm in inaccessible areas by simple ratcheting. Eliminates hand gripping effort and ensures perfect tracking. Allows quick and effi cient cutting of exhaust pipes in situ. The 13 alloy cutting wheels evenly cut diffi cult to reach thin wall pipes. The no-squeeze locking mechanism, avoids risk of lateral movement and disaligned cutting. Butterfl y screw allows easy feeding as cutting. LENGTH CAPACITY 10" Chain Pipe Cutter 250mm Ø 15-75mm GO10CPR 49b

52 Tools Holder / Hands Free Kit / Wire Rack GRIP-ON Holders Designed with special slot - fi rmly holds tools converting them into a versatile Portable Vice. The swivel pad ensures fi rm hold on all work pieces and the butterfl y screw makes for easy adjustment. GRIP-ON Holder to suit 10" Tools GRIP-ON Multi-holder to suit 5", 6", 7" and 10" Tools GO10GH GOMGH Hands Free Kit A unique concept which consists of 2 x GO10OR (10" Omnium Grip Locking Wrench) and 2 x GO10GH (10" Grip Holder) creating a true hands free work holding system. Just secure the GO10GH onto your work unit, insert the GO10OR into the slot and you have a Portable Vice. Repeat this with the other pair and you have 2 portable vices which, used together, allows fi rm holding of rod, pipe, or any other metal, wooden, or plastic sections, for cutting, gluing, welding, threading, etc. It all comes in a handy carry case for you convenience. Hands Free Kit (2 x GO10OR and 2 x GO10OR) GOHFK GRIP-ON Wire Rack Metallic wire rack for displaying a combination of 48 fast moving tools presented in GRIP-ON s unique display cards. GRIP-ON wire rack - holds 48 fast moving tools GOSTAND 49c

53 Tools Calipers / Wear Measuring Tool Metric / Imperial Digital Calipers Supplied in protective case Includes battery Clear LCD display with Zero switch Metric / Imperial digital calipers in protective case Replacement Battery to suit Supplied in protective case ME150E ME150B Trailer Hitch Wear Measuring Tool Universal inspection tool to check the wear limit of pin-or ball couplings and towing eyes Wear measuring tool

54 Tools Spanners Combination Spanner Ring end 15º offset Both ends the same size DIN 3113 Chrome-Vanadium SIZE 14mm 20mm 24mm 30mm 32mm H H H H H Double Open Ended Spanner Different size on each end DIN 3110 Chrome-Vanadium SIZE mm H Double Open Ended Spanner Set Different size on each end DIN 3110 Chrome-Vanadium CONTAINS THE FOLLOWING SIZES (mm) 6+7, 8+9, 10+11, 12+13, 14+15, 16+17, 18+19, H Double Offset Ring Spanner Different size on each end DIN 838 Chrome-Vanadium SIZE mm H mm H a

55 Tools Pliers Wire Stripper Insulated handle Claw type with screw adjustment Alloyed tool steel LENGTH 160mm H Pliers Set Insulated handle Alloyed tool steel CONTAINS THE FOLLOWING 1 x 250mm Water pump pliers 1 x 225mm Tower pincers 1 x 200mm Carpenter pincers H External Circlip Pliers For external circlips 19-60mm DIN 471 Circlips Sprung handgrips with straight or bent jaws Alloyed tool steel Straight Jaw - External circlip pliers to suit DIN 471 Circlips Bent Jaw - External circlip pliers to suit DIN 471 Circlips H H b

56 Tools Knives / Drill Bits 18mm Snap-Off Blades 18mm Snap-Off Blades to suit - Pack of 10 H Drill Bits Polished HSS Spiral Drill Bits For Steel and Cast Iron Produced to DIN Standard DIAMETER LENGTH (mm) (mm) MB MB MB MB MB MB MB c

57 Tools Grinding / Cutting Discs Cutting Discs Sold in boxes of 25 SIZE THICKNESS CENTRE TYPE SUITABLE FOR 4" 2.0mm 5/8" Depressed Centre Steel / Stainless Steel " 3.5mm 7/8" Flat Steel Only mm 1" Flat Steel Only Grinding Discs Sold in boxes of 10 SIZE THICKNESS CENTRE TYPE SUITABLE FOR 9" 6.0mm 7/8" Depressed Centre Steel / Stainless Steel d

58 Tools Wire Brush / Toolboxes / Bottle Jacks / Axle Stands Wire Brush Industrial wire brush with wooden handle Length 310mm 0.35mm wire in 16 x 4 rows Wire Brush 644 Vehicle Mounting Tool Box Length 370mm Width 150mm Height 140mm PVC Tool Box H Bottle Jacks Low pumping force facilitates work in diffi cult positions Also permits work in a horizontal direction Fitted with safety valve All Bottle Jacks Conform To Safety Standards HEIGHT STROKE CAPACITY MIN MAX Ton BJ Ton BJ Ton BJ Ton BJ Ton BJ20 Axle Stands (Supplied in Pairs) Compact axle stands are ideal for supporting vehicles such as cars, lorries, buses and agricultural machines. Detachable gear rack for safe stop and fast adjustment Spring-loaded pawl prevents unintentional release Stable, welded steel construction Observe maximum load capacity of the axle stands CAPACITY Pair of 3 Ton axle stands 3 Ton Pair of 6 Ton axle stands 6 Ton Terminals & Connectors c/w Pliers Supplied in plastic case Contains pliers for crimping, cutting and stripping CONTAINS THE FOLLOWING Terminal Pliers ONLY Terminal Pliers and the following terminals / connectors 10 x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA x LA9020 The complete listing of Terminals and Connectors is shown in our Tractor & Trailer Catalogue LAT1010 LAA

59 RECHARGEABLE Tools Flood Lamp / Torch / Inspection Lamps BATTERY Rechargeable LED Flood Lamp New Century LED Chip Colour temperature: 6500K CE / RoHS Approval IP65 Integrated rechargeable battery Supplied with mains and car chargers POWER VOLTAGE LUMINOUS DIMENSIONS INTENSITY Lm W x H x D 10W x 240 x 165 LAHS ADJUSTABLE Adjustable Torch Supplied with 6V battery Adjustable stand for hands free use Waterproof Adjustable torch complete with 6V battery Replacement battery to suit 6000 torch LED Mini Inspection Lamp With pocket clip Supplied with 3 x AAA batteries Mini LED inspection lamp c/w batteries LAHS

60 Tools Battery Chargers CTEK XS800 Battery Charger The XS800 easily charges all small batteries. It is perfect for motorcycles, lawnmowers and jetskis. It is also a maintenance charger for seasonal vehicles with batteries up to 100 Ah. Voltage: V AC Hz Battery charging capacity: Ah Max battery maintenance: 100 Ah Dimensions: 142 x 51 x 36mm Weight 0.3 kg Quick coupling function Dust and splash proof CTEK XS800 Battery charger XS800 CTEK XS3600 Battery Charger The XS3600 is a multi-task compact charger. It replaces all the chargers in your home. You can switch between lawnmowers, cars and RVs. It also has a cold weather mode for charging fl at batteries in winter. Voltage: V AC Hz Battery charging capacity: Ah Max battery maintenance: 120 Ah Dimensions: 165 x 61 x 38mm Weight 0.5 kg Quick coupling function Dust and splash proof CTEK XS3600 Battery charger XS3600 CTEK XS7000 Battery Charger The XS7000 is a universal charger for boats, cars and RVs. The supply mode provides you with power even without a battery. It also works as a memory saver so that you can unhook your battery without losing settings and codes on your vehicle computer, anti-theft radios, keyless entry systems etc. The Boost / Recon mode reconditions your battery after a deep discharge therefore your battery will recover quicker and last longer. Voltage: V AC Hz Battery charging capacity: Ah Max battery maintenance: 225 Ah Dimensions: 191 x 89 x 48mm Weight 0.8 kg Quick coupling function Dust and splash proof CTEK XS7000 Battery charger XS7000 CTEK XS2400 Battery Charger The XS7000 is a cost-effective charger, suitable for smaller 24V batteries. The XS2400 is ideal for maintenance charging of larger fl eets with 24V vehicles, backup systems, piste machinery, wheelchairs etc. Voltage: V AC Hz Battery charging capacity: Ah Max battery maintenance: 225 Ah Dimensions: 191 x 89 x 48mm Weight 0.8 kg Quick coupling function Dust and splash proof CTEK XS2400 Battery charger XS

61 Tools Battery Acid / Booster Cables ZIRCON Battery acid Battery acid - 1 litre bottle Battery acid - Carton containing 4 x 1 litre bottles BA BA3604 Note: A complete listings of batteries is shown in our Vehicle Electrics Catalogue or you can contact our Sales Staff with any Battery enquires you may have Booster Cables Supplied in display pack CABLE SIZE LENGTH STARTING LOAD 25mm 3.5 metre 350 Amp GS mm 4.5 metre 450 Amp GS3545 Replacement Parts to suit Booster cables Heavy duty battery clamps (set of 2 in display pack) MP

62 Tools Lashings / Winches / Manure Fork CERTIFIED Each strap has a certifi cation label Cargo Straps / Ratchet Lashings Ratchet lashings are manufactured from 100% polyester webbing with zinc plated hooks and ratchets. They are used for restraining loads on lorries, vans and trailers WIDTH LENGTH 25mm 5 metres TS2025A 50mm 8 metres TS2050B 50mm 10 metres TS2050C 50mm 12 metres TS2050G Note: Additional lengths are available upon request Ratchet Type Loadbinder to suit 10mm chain They are used for restraining loads on lorries, vans and trailers. They can be used in conjunction with standard loadbinders, ratchet type load binders, turnbuckles and commercial shackles. Loadbinder - Ratchet Type LBR10 Chain to suit Loadbinder is available to order. Contact a member of our Sales Staff with your inquiry. Trailer Winch With safety ratchets Fully zinc plated with precision made solid gear design CE Approved WORK BREAKING GEAR STRAP CAPACITY CAPACITY RATIO INCLUDED 250 Kg 720 Kg 1:3 Yes MP Kg 1500 Kg 1:4 No MP7974 STRAP TO SUIT 7 metre Polyester Winch Strap MP109 SCHMIEDETECHNIK SHW 4 Finger Silage Fork Sold in box of 5. Part Number is for a box of 5 Head: 310 x 230mm, 4 fi nger with 11mm thickness painted gold Handle: 36mm thickness, 1350mm (53") slightly curved ash-tree with clear seal SHW 4 fi nger silage fork with 1350mm handle (Box of 5) 54759SHW 55

63 Tools PTO Compressor C2 Compressor Spare Parts NO QTY PART NUMBER 1 Coupling with grub-screw 1 N.L.A. 2 Ball bearing Spacer 1 N.L.A. 4 Ball bearing ZZ 5 Crank Shaft 1 N.L.A. 6 Roller bearing NKG 10/20A 1 E Oil feeder 1 E Compressor body 1 N.L.A. 9 Pressure gauge 1 E Complete chain 1 N.L.A. 11 Hose connection with nut 1 N.L.A. 12 Safety valve 1 E Name plate elomatic 1 N.L.A. 14 Spiral hose 1 N.L.A. 15 Infl ating tyre connection 1 N.L.A. 16 Gasket with valve 2 N.L.A. 17 Piston 1 E Scraper ring 2 E Piston ring 4 N.L.A. 20 Cylinder Head 2 N.L.A. 21 Chain with hook 1 E Screw TE M8 x 30 8 N.L.A. 23 Washer 8.5 x 17 x N.L.A. 56

64 Air & Water Fittings One Touch Push In Fittings One Touch Push Fittings Convenient One touch fi ttings provide instant tubing connections Elliptical release ring facilitates pneumatic installations in confi ned spaces Light manual pressure on the elliptical release ring is all that is required to instantly disconnect each tube, no tools required. Nickel-plated brass threaded bodies ensures anti-corrosion and anti-contamination. All NPT & R(BSPT) thread are pre-coated with Tefl on sealant and require no additional sealing. Push-In Hose Connectors TO SUIT TUBE TO SUIT TUBE Straight Connector 90º Connector ' T ' Connector ' Y ' Connector ' X ' Connector 4mm 4mm PUC04PI PUL04PI PUT04PI PY04PI PZA04PI 5mm 5mm mm 6mm PUC06PI PUL06PI PUT06PI PY06PI PZA06PI 8mm 8mm PUC08PI PUL08PI PUT08PI PY08PI PZA08PI 10mm 10mm PUC10PI PUL10PI PUT10PI PY10PI PZA10PI 12mm 12mm PUC12PI PUL12PI PUT12PI PY12PI PZA12PI 14mm 14mm PUC14PI PUL14PI PUT14PI PY14PI - 16mm 16mm PUC16PI PUL16PI PUT16PI PY16PI - Metal Push-In Hose Connectors TO SUIT TUBE TO SUIT TUBE Straight Connector ' T ' Connector 4mm 4mm PM04PI MPE04PI 5mm 5mm PM05PI - 6mm 6mm PM06PI MPE06PI 8mm 8mm PM08PI MPE08PI 10mm 10mm PM10PI MPE10PI 12mm 12mm PM12PI MPE12PI 14mm 14mm PM14PI - Push-In Straight Reducer TO SUIT TUBE TO SUIT TUBE Straight Reducer 6mm 4mm PG06-04PI 8mm 4mm PG08-04PI 8mm 6mm PG08-06PI 10mm 6mm PG10-06PI 10mm 8mm PG10-08PI 12mm 8mm PG12-08PI 12mm 10mm PG12-10PI Push-In / Plug-In Straight Reducer TO SUIT TUBE TO SUIT TUBE Straight Reducer 6mm 4mm PGJ06-04PI 8mm 4mm PGJ08-04PI 8mm 6mm PGJ08-06PI 10mm 6mm PGJ10-06PI 10mm 8mm PGJ10-08PI 12mm 8mm PGJ12-08PI 12mm 10mm PGJ12-10PI 57

65 Air & Water Fittings One Touch Push In Fittings Push-In / Threaded Straight TO SUIT TO SUIT Straight Male Straight Male Straight Female Straight Female TUBE THREAD BSPT Thread BSPP Thread BSPT Thread BSPP Thread 4mm 1/8" PC04-01PI PC04-G01PI PCF04-01PI PCF04-G01PI 6mm 1/8" PC06-01PI PC06-G01PI PCF06-01PI PCF06-G01PI 6mm 1/4" PC06-02PI PC06-G02PI PCF06-02PI PCF06-G02PI 8mm 1/4" PC08-02PI PC08-G02PI PCF08-02PI PCF08-G02PI 8mm 3/8" PC08-03PI PC08-G03PI PCF08-03PI PCF08-G03PI 10mm 1/4" PC10-02PI PC10-G02PI PCF10-02PI PCF10-G02PI 10mm 3/8" PC10-03PI PC10-G03PI PCF10-03PI PCF10-G03PI 12mm 1/4" PC12-02PI PC12-G02PI PCF12-02PI PCF12-G02PI 12mm 3/8" PC12-03PI PC12-G03PI PCF12-03PI PCF12-G03PI Push-In / Threaded 90º and Banjo TO SUIT TUBE TO SUIT THREAD 90º BSPT Thread 90º BSPP Thread 90º Banjo BSPT Thread 90º Banjo BSPP Thread 4mm 1/8" PL04-01PI PL04-G01PI PH04-01PI PH04-G01PI 6mm 1/8" PL06-01PI PL06-G01PI PH06-01PI PH06-G01PI 6mm 1/4" PL06-02PI PL06-G02PI PH06-02PI PH06-G02PI 8mm 1/4" PL08-02PI PL08-G02PI PH08-02PI PH08-G02PI 8mm 3/8" PL08-03PI PL08-G03PI PH08-03PI PH08-G03PI 10mm 1/4" PL10-02PI PL10-G02PI PH10-02PI PH10-G02PI 10mm 3/8" PL10-03PI PL10-G03PI PH10-03PI PH10-G03PI 12mm 1/4" PL12-02PI PL12-G02PI PH12-02PI PH12-G02PI 12mm 3/8" PL12-03PI PL12-G03PI PH12-03PI PH12-G03PI Push-In / Threaded Male 'T' Branch TO SUIT TUBE TO SUIT THREAD ' T ' Branch BSPT Thread 4mm 1/4" PT04-02PI 6mm 1/4" PT06-02PI 6mm 3/8" PT06-03PI 6mm 1/2" PT06-04PI 8mm 1/4" PT08-02PI 8mm 3/8" PT08-03PI 8mm 1/2" PT08-04PI 10mm 1/4" PT10-02PI 10mm 3/8" PT10-03PI 10mm 1/2" PT10-04PI 12mm 1/8" PT12-02PI 12mm 3/8" PT12-03PI 12mm 1/2" PT12-04PI Push-In ON / OFF Valve TO SUIT TUBE TO SUIT TUBE ON / OFF Valve 4mm 4mm HVFF04PI 6mm 6mm HVFF06PI 8mm 8mm HVFF08PI 10mm 10mm HVFF10PI 12mm 12mm HVFF12PI 58

66 Air & Water Fittings One Touch Push In Fittings / Tubing Push-In / Threaded 90º Speed Controller TO SUIT TO SUIT 90º Controller 90º Controller TUBE THREAD BSPT Thread BSPP Thread 4mm 1/8" NSE04-01PI NSE04-G01PI 6mm 1/8" NSE06-01PI NSE06-G01PI 6mm 1/4" NSE06-02PI NSE06-G02PI 8mm 1/4" NSE08-02PI NSE08-G02PI 8mm 3/8" NSE08-03PI NSE08-G03PI 10mm 1/4" NSE10-02PI NSE10-G02PI 10mm 3/8" NSE10-03PI NSE10-G03PI 12mm 1/4" NSE12-02PI NSE12-G02PI 12mm 3/8" NSE12-03PI NSE12-G03PI Push-In Straight Speed Controller TO SUIT TUBE TO SUIT TUBE Speed Controller 4mm 4mm NSF04PI 6mm 6mm NSF06PI 8mm 8mm NSF08PI 10mm 10mm NSF10PI 12mm 12mm NSF12PI TO SUIT TO SUIT Speed TUBE THREAD Controller 6mm 1/4" BSPT NSFSF06-02PI Nylon-Tube PA6 Suitable for Oil TUBE OD BLACK PA6 CLEAR PA6 4mm NY604BPI NY604CPI 6mm NY606BPI NY606CPI 8mm NY608BPI NY608CPI 10mm NY610BPI NY610CPI 12mm NY612BPI NY612CPI 14mm NY614BPI NY614CPI Polyurethane Pipe Suitable for Air TUBE OD 4mm 6mm 8mm 10mm 12mm 14mm BLUE PU04BEPI PU06BEPI PU08BEPI PU10BEPI PU12BEPI PU14BEPI 59

67 Air & Water Fittings Claw Couplings Claw Coupling with Hosetail Pneumatic Fitting HOSETAIL SIZE 1/2" CLAW0513 5/8" CLAW0516 3/4" CLAW0519 1" CLAW0525 Claw Coupling Blanking Plug Pneumatic Fitting Claw coupling blank plug CLAW04 Claw Coupling Female Thread Pneumatic Fitting THREAD SIZE 1/2" BSP CLAW0108 3/4" BSP CLAW0112 1" BSP CLAW0116 Claw Coupling Male Thread Pneumatic Fitting THREAD SIZE 1/2" BSP CLAW0208 3/4" BSP CLAW0212 1" BSP CLAW0216 Claw Coupling House Clamp Pneumatic Fitting TO SUIT HOSE 22-29mm CLAW mm CLAW mm CLAW

68 Air & Water Fittings Air Couplings 60' Series - Air Line Couplings & Adaptors The 60' Series is designed for general industrial applications Free fl ow rate at 7bar (100lbf/in2) 55 to 60ft 3/min 1557 to 1697 Litres/min Coupling Body with Female Thread Coupling Body with 1/4" BSP Female Thread - Taper Coupling Body with 1/2" BSP Female Thread - Taper Integral Adaptor / Tailpiece Integral Adaptor with 1/2" Tailpiece Male Threaded Adaptor Adaptor with 1/4" BSP Male Thread - Taper Airflow Couplings A popular coupling for use with portable air tools, garage and industrial air line systems and test panels Free fl ow rate at 7bar (100lbf/in2) 35 to 42ft 3/min 991 to 1133 Litres/min Coupling Body with Male Thread Coupling Body with 1/4" BSP Male Thread - Taper 143 Coupling Body with 3/8" BSP Male Thread - Taper 383 Coupling Body with Female Thread Coupling Body with 1/4" BSP Female Thread - Taper 141 Coupling Body with 3/8" BSP Female Thread - Taper Standard Air Line Couplings Hose Tail with Male Thread 3/8" Hose Tail with 1/4" BSP Thread - Taper /2" Hose Tail with 1/4" BSP Thread - Taper /8" Hose Tail with 3/8" BSP Thread - Taper

69 Air & Water Fittings Air Couplings / Air Guns PLC Standard Adaptors Case hardened for longer life Female Threaded Adaptor Adaptor with 1/4" BSP Female Thread - Taper 144 Male Threaded Adaptor Adaptor with 1/4" BSP Male Thread - Taper 142 Integral Adaptor / Tailpiece Integral Adaptor with 5/16" Tailpiece 5161 Integral Adaptor with 3/8" Tailpiece 381 Pistol Type Air Blow Gun Suitable for cleaning liquid, swarf or dust during manufacture or assembly. Supplied complete with two nozzles - Standard (single hole) and Pepperpot (multi-hole) Pistol Type Air Blow Gun with 1/4" BSP Female Thread K4 Air Tyre Inflator Pistol-grip with Dial Gauge (0-10 Bar or PSI) and clip-on connector. Ideal for the hobbyist and professional user. Suitable for use with motor vehicles, cycles, dinghies, etc. Air Tyre Infl ator with Dial Gauge 4288 AIRFORCE MK4 Airline Gauge The AIRFORCE MK4 Tyre Infl ator is a robust and highly accurate, offering leading infl ation and defl ation rates and high performance for both indoor and outdoor applications. The redesigned piston and seal arrangement means increased accuracy - cycle tests now give over 400,000 infl ation cycles at 100% accuracy Complies to: EC 86/217, EN12645:2014 Reading Accuracy: 0.1 bar / 2 psi Maximum Inlet Pressure: 13.8 bar / 200 psi Inflation Flow: 500 l/min / 18 cfm Operating Temperature: -25 to 55 C Airforce MK4 Airline Gauge Supplied in hang pack carton PCLGUN 62

70 Air & Water Fittings Air / Water Hose Espiroaspersion - PVC Water Hose Temperature Range: -10ºC to +60ºC Description: Soft PVC hose reinforced by a polyester mesh for water delivery in fl ower growing and agriculture. Applications: Agriculture, Gardening, Industrial, Construction, Marine and Home. Advantages: Good resistance to abrasion and sudden temperature changes. Excellent weather resistance. High visibility even in very low light conditions. Resistant to atmospheric and chemical products. I.D O.D. WEIGHT WORKING BURSTING ROLL (mm) (mm) PER METER PRESSURE (20ºC) PRESSURE (20ºC) LENGTH g 8 bar 24 bar 50 metres g 8 bar 24 bar 50 metres g 8 bar 24 bar 50 metres g 7 bar 21 bar 50 metres 2512 WATER Agripres AIR WATER SPRAYER Temperature Range: -10ºC to +60ºC Description: PVC hose with polyester yarn reinforcement Applications: Agriculture, Industrial, Construction, and Transport. I.D O.D. WEIGHT WORKING BURSTING ROLL mm mm PER METER PRESSURE PRESSURE LENGTH g 20 bar 60 bar B g 20 bar 60 bar B g 20 bar 60 bar B Air Hose Temperature Range: Description: Applications: I.D mm -10ºC to +60ºC SBR blended with black wrapped surface, textile braided high tensile synthetic yarn. Weather and ozone resistant. Compressed air O.D. mm WEIGHT PER METER WORKING PRESSURE BURSTING PRESSURE ROLL LENGTH g 20 bar 60 bar B g 20 bar 45 bar B AIR 63

71 Air & Water Fittings Air / Water Hose Mallatrans Hose (Food Quality) Temperature: Description: Applications: Advantages: AIR WATER FOOD -10ºC to +60ºC. PVC transparent hose with polyester yarn reinforcement, for delivery of water, cooling fl uids, chemical solutions, food and compressed air. Agriculture, Industrial, Construction, Marine, Transport and Home. Lightweight and very fl exible. Resistant to weather conditions. I.D O.D. WEIGHT WORKING BURSTING ROLL (mm) (mm) PRESSURE PRESSURE LENGTH gr/mtr 15 bar 45 bar 50 metres gr/mtr 15 bar 45 bar 50 metres gr/mtr 15 bar 45 bar 50 metres gr/mtr 15 bar 45 bar 50 metres gr/mtr 15 bar 45 bar 50 metres gr/mtr 10 bar 30 bar 50 metres gr/mtr 10 bar 30 bar 50 metres gr/mtr 7 bar 21 bar 50 metres gr/mtr 6 bar 18 bar 50 metres gr/mtr 5 bar 15 bar 25 metres 5060H General Purpose Hose - Bursting Pressure 60 bar Temperature Range: -40ºC to +100ºC Description: Synthetic rubber hose, textile spiral construction. Highly fl exible and weather and resistant Applications: Suitable for mineral oils, diesel and petrol with a maximum aromatic content of 40%, air and water Please Note: Hose is sold in 50 metre rolls only I.D O.D. WEIGHT WORKING MIN. BURSTING ROLL mm mm PER METER PRESSURE PRESSURE LENGTH g 20 bar 60 bar 50 metres GP g 20 bar 60 bar 50 metres GP g 20 bar 60 bar 50 metres GP g 20 bar 60 bar 50 metres GP g 20 bar 60 bar 50 metres GP g 20 bar 60 bar 50 metres GP g 20 bar 60 bar 50 metres GP6025 P PETROL D DIESEL OIL AIR WATER 64

72 Air & Water Fittings GEKA Fittings GEKA Type Hose End Coupling HOSE TAIL SIZE Hose End Coupling - GEKA Type 3/8" Hose End Coupling - GEKA Type 1/2" Hose End Coupling - GEKA Type 5/8" Hose End Coupling - GEKA Type 3/4" Hose End Coupling - GEKA Type 1" Hose End Coupling - GEKA Type 1 1/4" Hose End Coupling - GEKA Type 1 1/2" GEKA Type Female Coupling HOSE TAIL SIZE Female Coupling - GEKA Type 3/8" Female Coupling - GEKA Type 1/2" Female Coupling - GEKA Type 3/4" Female Coupling - GEKA Type 1" Female Coupling - GEKA Type 1 1/4" Female Coupling - GEKA Type 1 1/2" GEKA Type Male Coupling HOSE TAIL SIZE Male Coupling - GEKA Type 3/8" Male Coupling - GEKA Type 1/2" Male Coupling - GEKA Type 3/4" Male Coupling - GEKA Type 1" Male Coupling - GEKA Type 1 1/4" Male Coupling - GEKA Type 1 1/2" GEKA Type 'Y' Adaptor 'Y' Adaptor - GEKA Type GEKA Type Blanking Cap Blanking Cap - GEKA Type GEKA Type Sealing Ring Sealing Ring - GEKA Type

73 Air & Water Fittings Brass Fittings Spray Nozzle with Insert Nipple Spray Nozzle Rubber O' Ring to suit WK OR Insert Nipple with Hose Connection HOSE SIZE Insert Nipple with Hose Connection 1/2" WK33021 Insert Nipple with Hose Connection 3/4" WK33022 Rubber O' Ring to suit OR Coupling with Hose Connection HOSE SIZE Coupling with Hose Connection 1/2" WK33031 Coupling with Hose Connection 3/4" WK33032 Coupling with Hose Connection c/w Valve HOSE SIZE Coupling with Connection & Valve 1/2" WK33041 Coupling with Connection & Valve 3/4" WK º Insert Nipple with Female Threaded End THREAD SIZE 90º Insert Nipple with Female Threaded End 3/4" WK33062 Rubber O' Ring to suit OR Nipple with Female Threaded End THREAD SIZE Insert Nipple with Female Threaded End 1/2" WK33121 Insert Nipple with Female Threaded End 3/4" WK33122 Insert Nipple with Female Threaded End 1" WK33123 Rubber O' Ring to suit OR Nipple with Male Threaded End THREAD SIZE Insert Nipple with Male Threaded End 1/2" WK33221 Insert Nipple with Male Threaded End 3/4" WK33222 Rubber O' Ring to suit OR 66

74 Air & Water Fittings Brass Fittings / Water Guns Hose Connection HOSE SIZE Hose Connection 1/2" WK33321 Hose Connection 3/4" WK Way Insert Nipple 2-Way Insert Nipple Rubber O' Ring to suit WK OR 3-Way Insert Nipple 3-Way Insert Nipple Rubber O' Ring to suit WK OR 'Y' Connection with 1 x 3/4" Female & 2 x Nipple Ends Shut-Off Valves on both Nipple Ends 'Y' Connection with 3/4" Female Rubber O' Ring to suit WK OR 'Y' Connection with 1 x 3/4" Female & 2 x Nipple Ends Shut-Off Valves on both Nipple Ends 'Y' Connection with 3/4" Female Rubber O' Ring to suit WK OR Water Guns Standard 3/4" BSP water gun trigger spray Heavy Duty 1/2" BSP water gun trigger spray Hosetail to suit WG2-1/2" BSP x 13mm hosetail WG1 WG2 BRASSHT

75 Hydraulic Hose Machines Hose Cutting EM400 Hose Cutting Machine Cutting Range: 1-2 wire 1 1/4", 4 wire 1" Dimensions (LxWxH): 500 x 350 x 600mm Drive: Electric Motor POWER Hose cutting machine 220V 1.5kW EM4001PH Hose cutting machine 380V 1.5kW EM400 Replacement blade to suit EM400 hose cutting machine EM250 EM3 Ecoline Hose Cutting Machine Strong and robust, meeting CE safety standards for operator protection. Cutting Range: 1-2 wire 1 1/4", 4 wire 1" Drive: Electric Motor Cutting Blade: 200 x 1.6 x 30mm or 200 x 1.6 x 25.4mm Dimensions (LxWxH): 400 x 510 x 540mm Weight: 20 Kg POWER Hose cutting machine 220V 1.8kW EM31PHECOLINE Replacement blade - 30mm centre (pre 2011) TMG Replacement blade mm centre (from 2011) TMG EM3 Hose Cutting Machine Strong and robust, meeting CE safety standards for operator protection. Cutting Range: 4 wire 1 1/4" Drive: Electric Motor Cutting Blade: 275 x 3.0 x 30mm Dimensions (LxWxH): 540 x 440 x 300mm Weight: 50 Kg POWER Hose cutting machine 380V 3.0kW EM3 Replacement blade to suit EM3 hose cutting machine TMG EM2 Hose Cutting and Brushing Machine Strong and robust, meeting CE safety standards for operator protection. Suitable for bench mounting. Cutting Range: 1 & 2 wire up to 1 1/4", 4 wire up to 1 1/4" Drive: 3 kw Cutting Blade: 275 x 3 x 30mm Brushing: Yes Dimensions (LxWxH): 630 x 440 x 330mm Weight: 65 Kg POWER Hose cutting machine 3 Phase EM2 Replacement blade to suit EM2 hose cutting machine TMG

76 Hydraulic Hose Machines Hose Swaging S2MH Manual Swaging Machine Ideal for mobile or workshop crimping Supplied with 8 Dies sets Crimp Force: 900 kn / 90 Ton Advantage: Slide bearings on the crimp tool, no service and 20% less friction Working Range: 2 wire up to 1 1/4" 4 wire up to 1" Dies Supplied: 14, 17, 20, 24, 28, 32, 36 and 40mm Opening: +22mm Opening without Dies: 77mm Oil: 0.75 (litres) Dimensions (LxWxH): 170 x 220 x 330mm Weight: 31 Kg Includes 8 Die Sets POWER Manual swaging machine Manual S2MH 69

77 Hydraulic Hose Machines Hose Swaging HM200 Ecoline HM200 & HM200 Ecoline Swaging Machines HM200 HM200 ECOLINE Crimp Force: 1300 kn / 130 Ton 1300 kn / 130 Ton Working Range: 1 & 2 Wire up to 1 1/2" 4 Wire up to 1 1/4" 1 & 2 Wire up to 1 1/2" 4 Wire up to 1 1/4" Opening: +30mm +30mm Opening without dies: 100mm 100mm Speed (mm/sec) Close / Crimp / Open: 3.5 / 3.5 / / 3.5 / 5.9 Oil: 40 l (DC 4 l) 40 l (DC 4 l) Dimensions (LxWxH): 800 x 530 x 630mm 420 x 535 x 520mm Power Unit Dimensions: x 450 x 560mm DC Power Unit Dimensions: x 270 x 230mm Dies Supplied 14, 20, 24, 28, 32, 40, 44 and 50mm 17, 20, 24, 28, 32, 36, 44 and 50mm Weight 140 Kg 88 Kg Supplied with QDC Quick Die Change System POWER HM200 swaging machine 1 Phase HM2001PH HM200 swaging machine 3 Phase HM200 HM200 Ecoline swaging machine 1 Phase HM200ECOLINE1PH HM200 Ecoline swaging machine 3 Phase HM200ECOLINE HM200 Ecoline swaging machine 12 Volt HM200ECOLINE12V HM200 Ecoline swaging machine 24 Volt HM200ECOLINE24V HM200 Supplied with Quick Die Change System The Quick Die Change System and Die Holder which allows you to easily swap a full set of Dies in seconds. x 8 Die Locator Pin Set to suit HM200 & HM200 Ecoline PINS PER SET Replacement die locator pin set to suit HM SW S3 & S3 Ecoline Swaging Machines S3 S3 ECOLINE Crimp Force: 1200 kn / 120 Ton 1200 kn / 120 Ton No Grease 20% less friction: Yes Yes Working Range: 1 & 2 Wire up to 1 1/2" 4 Wire up to 1 1/4" 1 & 2 Wire up to 1 1/2" 4 Wire up to 1 1/4" Opening: +35mm +35mm Opening without dies: 103mm 103mm Speed (mm/sec) Close / Crimp / Open: 8.6 / 8.6 / / 4.0 / 6.5 Oil: 35 l 35 l Dimensions (LxWxH): 720 x 600 x 672mm 592 x 545 x 672mm Dies Supplied: 17, 20, 24, 28, 32, 36, 44 and 50mm 17, 20, 24, 28, 32, 36, 44 and 50mm Weight: 193 Kg 150 Kg S3 Supplied with QDC Quick Die Change System POWER S3 swaging machine 3 Phase S3 S3 Ecoline swaging machine 1 Phase S3ECOLINE1PH S3 Ecoline swaging machine 3 Phase S3ECOLINE3PH S3 Ecoline swaging machine 12 Volt S3ECOLINE12V S3 Ecoline swaging machine 24 Volt S3ECOLINE24V Supplied with Quick Die Change System The Quick Die Change System and Die Holder which allows you to easily swap a full set of Dies in seconds. S3 Ecoline 70

78 Hydraulic Hose Machines Hose Swaging S4 S4 & S4 Ecoline Swaging Machines S4 S4 ECOLINE Crimp Force: 1800 kn / 180 Ton 1800 kn / 180 Ton No Grease 20% less friction: Yes Yes Working Range: 1 & 2 Wire up to 2" 4 Wire up to 1 1/2" 1 & 2 Wire up to 2" 4 Wire up to 1 1/2" Opening: +35mm +35mm Opening without dies: 103mm 103mm Speed (mm/sec) Close / Crimp / Open: 5.9 / 5.9 / / 2.7 / 4.7 Oil: 35 l 35 l Dimensions (LxWxH): 720 x 600 x 672mm 592 x 545 x 672mm Dies Supplied: 17, 20, 24, 28, 32, 36, 47, 54 and 62mm 17, 20, 24, 28, 32, 36, 47, 54 and 62mm Weight: 203 Kg 160 Kg POWER S4 swaging machine 3 Phase S4 S4 Ecoline swaging machine 1 Phase S4ECOLINE1PH S4 Ecoline swaging machine 3 Phase S4ECOLINE S4 Ecoline swaging machine 12 Volt S4ECOLINE12V S4 Ecoline swaging machine 24 Volt S4ECOLINE24V Supplied with Quick Die Change System The Quick Die Change System and Die Holder which allows you to easily swap a full set of Dies in seconds. S4 Ecoline S8 Swaging Machine Crimp Force: 2200 kn / 220 Ton No Grease 20% less friction: Yes Working Range: 1 & 2 Wire up to 2", 4 Wire up to 1 1/2" Industrial: 4" Opening: +45mm Opening without dies: 190mm Speed (mm/sec) Close / Crimp / Open: 6.1 / 1.7 / 10.3 Oil: 55 l Dimensions (LxWxH): 690 x 600 x 1400mm Dies Supplied: 17, 20, 24, 28, 32, 36, 44 and 50mm Weight 390 Kg POWER Swaging Machine 3 Phase S8 Supplied with Quick Die Change System The Quick Die Change System and Die Holder which allows you to easily swap a full set of Dies in seconds. The company UNIFLEX-Hydraulik GmbH was established by the engineer Peter Schröck in Frankfurt/Main in Based on its trailblazing innovations and high-quality products, it quickly grew into a leading supplier of machines used for producing hose assemblies. Based on its years of cooperation with many manufacturers of hose assemblies, UNIFLEX has developed a comprehensive program of machines designed for producing hose assemblies. It provides cutting machines, presses, testing systems and cleaning machines. In this way, UNIFLEX has become an innovative system supplier from workshop equipment to production plants. 71

79 Hydraulic Hose Machines Hose Skiving / Pipe Bending USM10 Hose Skiving Machine External Skiving: 3/16" to 2" Internal Skiving: 5/8" to 2" Noise Level: 60 dba Drive: 0.37 kw Length / Width / Height: 260 x 440 x 500 Bench Mountable: Yes Weight: 35 Kg Supplied with External Skiving Mandrels. Internal Skiving Mandrels available upon request. POWER Hose skiving machine 1 Phase USM10ECOLINE Hose skiving machine 3 Phase USM10 USM2 Hose Skiving Machine (Manual) Ideal for mobile hose repair - no power required External Skiving: 3/16" to 2" Internal Skiving: 5/8" to 2" Drive: Manual Length / Width / Height: 338 x 465 x 445mm Max Outside Diameter: Ø 80mm Bench Mountable: Yes Weight: 16 Kg Supplied with External Skiving Mandrels. Internal Skiving Mandrels available upon request. POWER Hose skiving machine Manual USM2 Pipe Bending Tool Design: For bending pipes. The rollers have an optimum radius. Maximum 180º Material: Bending rollers: Aluminium alloy Technical Information: Place the pipe bending machine in a bench vice for optimal stability PIPE Ø Pipe bending tool with rollers 6-12mm 6-12mm Pipe bending tool with rollers 10-18mm 10-18mm

80 Castors Swivel Castors Swivel Castor with Nylon Wheel - Light Duty White nylon wheel Kg x x WH x x WH x x WH x x WH x x WH x x WH Swivel Castor with Nylon Wheel - Medium Duty High quality nylon 6 wheel Kg x x WH50NK x x WH50NK x x WH50NK x x WH50NK x x WH50NK x x WH50NK200 Swivel Castor with Rubber Tyre Black rubber tyre with steel fl anges Kg x x WH x x WH x x WH x x WH x x WH x x WH x x WH x x WH Swivel Castor with Cast Iron Wheel Cast iron wheel with polyurethane coating Kg x x WH x x WH x x WH x x WH x x WH x x WH Swivel Castor with Pneumatic Tyre Pneumatic tyred wheel with pressed and zincated steel plate Kg x x WH50PN

81 Castors Swivel Castors / Swivel Castors with Brakes Swivel Castor with Nylon Wheel Zincate Swivel Castor Kg x x WH50NK250 Swivel Castor with Nylon Wheel & Brake High quality nylon 6 wheel Kg x x WH50NF x x WH50NF x x WH50NF x x WH50NF x x WH50NF x x WH50NF x x WH50NF250 Swivel Castor with Rubber Tyre & Brake Black rubber tyre with steel fl anges Kg x x WH x x WH x x WH x x WH x x WH x x WH x x WH x x WH Swivel Castor with Cast Iron Wheel & Brake Cast iron wheel with polyurethane coating Kg x x WH700P x x WH700P x x WH700P x x WH700P x x WH700P x x WH700P250 Swivel Castor with Pneumatic Tyre & Brake Pneumatic tyre wheel, pressed and zincated steel plate Kg x x WH50PNT

82 Castors Fixed Castors Fixed Castor with Nylon Wheel - Light Duty White nylon wheel Kg x x80 75 WH x x80 90 WH x x WH x x WH x x WH x x WH Fixed Castor with Nylon Wheel - Medium Duty High quality nylon 6 wheel Kg x x WH51NK x x WH51NK x x WH51NK x x WH51NK x x WH51NK x x WH51NK x x WH51NK250 Fixed Castor with Rubber Tyre Black rubber tyre with steel fl anges Kg x x WH x x WH x x WH x x WH x x WH x x WH x x WH x x WH Fixed Castor with Cast Iron Wheel Cast iron wheel with polyurethane coating Kg x x WH x x WH x x WH x x WH x x WH x x WH Fixed Castor with Rubber Wheel Black Rubber Tyre with Thermoplastic Core Kg x x WH451B

83 Castors Fixed Castors / Castor Wheels Fixed Castor with Pneumatic Tyre Pneumatic tyre wheel with pressed and zincated steel plate Kg x x WH51PN260 Nylon Castor Wheel without Bearing White nylon wheel, hub with smooth hole Kg WH WH WH WH WH WH86200 Nylon Castor Wheel c/w Ball Bearing Quality nylon 6 wheel, hub with ball bearing Kg x WH840N x WH840N x WH840N x WH840N x WH840N x WH840N x WH840N250 Castor Wheel wtih Rubber Tyre Black rubber tyre, steel fl anges, hub on nylon bush & roller bearing Kg WH WH WH WH WH WH WH WH81250 Cast Iron Castor Wheel Cast iron wheel with polyurethane coating, hub on ball bearing Kg x WH x WH x WH x WH x WH x WH

84 Cargo Care Castor Wheels Castor Wheel with Pneumatic Tyre Pneumatic tyre wheel with pressed and zincated steel plate. Hub on roller bearing Kg WH81PN WH81PN26025 Pallet Truck Wheel Steel roller with polyurethane coating Kg x WH200P x WH200P x WH200P x WH200P x WH200P82100 Pallet Truck Wheel High-resistance nylon 6 roller with injected polyurethane coating Kg x WH200NP x WH200NP x WH200NP x WH200NP

85 Personal Protection Visors / Helmets Nylon Face Shield with Mesh Visor Nylon face shield with mesh visor FGP Nylon Face Shield with Mesh Visor and Ear Defenders Nylon face shield with mesh visor and ear defenders FGP Nylon Face Shield with PVC Visor and Ear Defenders Nylon face shield with PVC visor and ear defenders FGP Supplied in display box Forestry Helmet with Mesh Visor and Ear Defenders Helmet EN 397 with adjustable head ring Ear protection EN 352 Face protection EN 89/686/CEE Forestry helmet with mesh visor and ear defenders FH

86 Personal Protection Ear Muffs / Plugs Ear Muffs with Headband Provides excellent protection that fi lters high frequency noise originating from dynamic machines such as Workshop Equipment, Motor Saws etc. This hearing protection complies with the requirements of the European Directive 89/686/CEE annexx II by means of the European Standard EN352-1:1993. Adjustable headband. Weight: 166g. Ear muffs with adjustable headband FGP Ear Muffs with Headband European Standard EN352. Adjustable headband which can collapse to allow for easy storage in pocket. Weight: 178g. Ear muffs with adjustable and collapsible headband FGP Peltor Optime II Lower tones and higher volume. Increased muffl ing, primarily for lower frequencies (which also covers high frequencies) This fi rst-rate muffl ing gives suitable protection in most noise-hazard situations Peltor Optime II ear defender WP Ear Plugs Classic earplugs are made from a soft energy absorbing polymer foam, which allows the user to roll the plug down for easy insertion into the ear canal and then expand slowly to form a comfortable seal against noise. Classic ear plugs WP

87 Personal Protection Gloves Nitrile Gloves - Disposable Strong, latex-free disposable glove - ideal for light chemical handling and food contact Powder-free. 100 ambidextrous gloves per box. Approved to BS EN 455 and BS EN 374 SIZE Nitrile gloves - Box of 100 Large DNG02L Nitrile gloves - Box of 100 X Large DNG02XL Heavy Duty Nitrile Gloves - Disposable Heavy Duty Superior nitrile glove that offers unparalleled strength and grip Diamond Grip pattern both outside and in for enhanced grip Combines the strength of a household with the fi t and feel of a disposable Hi Viz orange colour to allow dirt to be easily identifi ed Approved to BS EN 420:2003. SIZE Heavy Duty Nitrile gloves - Box of 50 Large DNG01L Heavy Duty Nitrile gloves - Box of 50 X Large DNG01XL Latex Work Gloves Woven cotton glove with a latex covered palm and knuckle area SIZE Working gloves - cotton and latex X Large HS1181 Latex Work Gloves Nu-Grip work gloves, cotton with laminated black latex palm. SIZE NU-Grip work gloves Large NG09 NU-Grip work gloves X Large NG

88 Personal Protection Gloves / Goggles / Glasses Rigger Gloves Leather glove with a cotton lining, doubled stitched SIZE Rigger gloves - leather with cotton lining X Large HS1125 Chainsaw Protection Gloves Leather gloves with knitted wrist. SIZE Chainsaw protection gloves Medium HS1339GP Chainsaw protection gloves Large HS1340GP Chainsaw protection gloves X Large HS1341GP Goggles PVC body with ventilation holes Adjustable elastic strap Weight: 60g PVC Goggles with ventilation hole FGP Anti-Scratch Safety Glasses European Standard EN170. Polycarbonate Anti-scratch and Anti-UV Resistance impact Can be worn over glasses Weight: 45g Ant-scratch safety glasses FGP Safety Glasses European Standard EN170 for clear, EN172 for tinted. Polycarbonate Anti-UV Resistance impact Weight: 23g COLOUR Safety glasses Clear FGP Safety glasses Tinted FGP

89 Personal Protection Masks / Leg Protection / Harnesses B-Brand P2V Mask - Valved Polypropylene (P.P) outer layer provides smooth lining and avoids loose fi bres Embossed fringe seal avoids fl uffy open layers around the edges Latex free synthetic rubber head strap Contour design ensures the compatibility of glasses / goggles and reduces fogging Soft close-cell nose foam and adjustable nosepiece ensures custom shape and increases the worker comfort EN149:2001 P2V Mask with valve BBP2V Shin Protectors Provides protection from knees to the ankles Shin protection made from polyethylene Adjustable straps with quick release clips Lined with pre-formed, comfortable material Universal size Shin protectors - pack of 2 FGP Pro Harness Harness with 2 shoulder straps FGP Universal Harness Universal harness FGP