macnaught lubrication & greasing equipment

Transcription

1 macnaught lubrication & greasing equipment

2 Since its foundation in 1948, Macnaught Pty Ltd has been designing, engineering, manufacturing and supplying high quality lubrication and fluid management equipment into agricultural, industrial and automotive markets around the world. Macnaught also specialises in manufacturing unique products for the mining, aviation and marine industries. Macnaught has worked hard over the years to become a respected leader in its field and to develop a name synonymous with high quality yet affordable equipment. With its strong customer, R & D and global focus, Macnaught will continue to be a leader for many years to come. Macnaught is an environmentally responsible and globally respected supplier of fluid management solutions. Macnaught is committed to: Efficient energy use practices and production efficiency Waste minimisation and recycling Pollution prevention Preservation of our unique local environment and surrounding ecosystems Research and development on the environmental performance of Macnaught products Meeting and exceeding applicable legislation and regulations Through the active participation of all employees in Macnaught s Environmental Management System, Macnaught demonstrates its commitment to responsible environmental management and continuous improvement. macnaught.com.au

3 3

4 Macnaught has built up an enviable reputation in more than sixty countries around the world for innovation with products and packaging tailored specifically to individual market needs. It s distributors are market leaders in their respective countries and their knowledge of the Macnaught range means that assistance, parts and servicing is never too far away. While Macnaught is 100% Australian owned, it has a strong commitment to export markets. Highlighting the importance placed on export successes and to service the growing needs in multiple regions, Macnaught has sales offices in Singapore, Indonesia, USA and the UK. macnaught.com.au

5 Contents Greasing Equipment Hand Operated 6 Air Operated 11 Battery Powered 16 Dispensing Guns 17 Lubricators 18 Fittings 19 Fuel Handling Equipment Hand Operated Fuel Equipment 20 Diesel Fuel Pumps 24 Oil Transfer Equipment Hand Operated Oil Pumps 27 Hand Operated Chemical Pumps 31 Air Operated Oil Pumps 32 Oil Control Guns 39 Flow Meters Fuel Meters 46 Water Meters 48 Oil Meters 49 Hose Reels Retracta Auto Rewind Hose Reels 50 Metal Reels 52 Oil And Grease Systems 54 Specialty Pumps 57 Fluid management & control systems 58 Accessories 60 Quick Selection Guide 69 5

6 greasing equipment - hand operated super-lube K3 The K3 is a manual greasing system designed for powerful, professional greasing. A cost effective solution for all workshop greasing requirements, Macnaught produces models to suit pails from 12.5 kg (28 lbs) up to 22 kg (48 lbs) with depths of 310 mm to 430 mm. includes pump unit, lid, rubber edged follower, 3 m (10 ft) x (1 2 ) ID delivery hose, and the high pressure, high volume KR grease gun (all components available separately) spring loaded pump system provides 60 shots of grease suitable for greases up to and including NLGI No swivel to prevent hose kinking fully sealed to prevent contamination optional TR5 drum trolley to provide portability K3 Super-Lube wetted components: aluminium, steel, brass and nitrile rubber gun pressure (on high pressure): up to kpa ( psi, 690 bar) output: approx g on the high volume switch approx g on the high pressure switch (to clear a blocked or seized nipple) Accessories KZD Needlenose Coupler KZHY Hyperdermic Needlepoint coupler KFR Rigid/Flexible Extension KDF13 Flexible Extension TR5 Trolley TR5 Trolly 6

7 greasing equipment - hand operated mini-lube K6 The K6 is a portable, manual greasing system designed for use both in workshop environments and for on site applications. Macnaught produces models to suit pail sizes from 2.5 kg (5 lbs) to 5 kg (11 lbs) with depths of 146 mm to 225 mm. K6 Mini-Lube includes pump unit, lid, rubber edged follower, 1.5 m (5 ft) x 1 2 ID delivery hose, and the high pressure, high volume KR grease gun (all components also available separately) K6-24 contains the above items plus a 2.5 kg (5 lbs) refillable container (KT5), while the K6-67 contains the above items plus a 5 kg (11 lbs) refillable container (KT6) spring loaded pump system provides 30 shots of grease suitable for greases up to and including NLGI No swivel to prevent hose kinking fully sealed to prevent contamination wetted components: aluminium, steel, brass and nitrile rubber gun pressure (on high pressure): up to kpa ( psi, 690 bar) output: approx g on the high volume switch approx g on the high pressure switch (to clear a blocked or seized nipple) Accessories KT5 (2.5 kg)/kt6 (5 kg) Grease Container KZD Needlenose Coupler KZHY Hyperdermic Needlepoint coupler KFR Rigid/Flexible Extension KDF13 Flexible Extension KSR Standard Buttonhead Coupler KT5 (2.5 kg)/kt6 (5 kg) Grease Container 7

8 greasing equipment - hand operated flexigun K g (15.9oz) cartridge K29-Z Zinc version 450 g (15.9oz) cartridge K g (14.5oz) cartridge The Flexigun is a high quality pistol grip grease gun, incorporating a unique variable stroke operation. The Flexigun is able to reach increased greasing pressures from short strokes and high greasing volumes from full strokes. K29 Flexigun one hand operation handles up to and including NLGI No.2 greases supplied complete with 230 mm (9 ) flexible extension and KY coupler can be filled by bulk, cartridge or the J2 Grease Pump optional range of couplers and extensions available zinc version (K29-Z) available for use in underground coal mines fully repairable also available in the FGK1 Flexi Greasing Kit FGK1 Flexi Greasing Kit wetted components: aluminium, steel and nitrile rubber (and zinc for model K29-Z) output: up to kpa (7 500 psi, 520 bar), 0.68 g per shot Accessories KZD Needlenose Coupler KZHY Hyperdermic Needlepoint coupler KFR Rigid/Flexible Extension KDF13 Flexible Extension KFR Rigid/Flexible Extension 8

9 greasing equipment - hand operated levergun K g (14.5oz) cartridge K g (15.9oz) cartridge The Levergun is a high quality, lever action grease gun manufactured for professional use. Designed for high pressure, high volume greasing, this classic gun can easily clear blocked or damaged grease nipples. two hand operation handles up to and including NLGI No.2 greases supplied complete with 170 mm (6 3 4 ) rigid extension and KY coupler can be filled by bulk, cartridge or the J2 Grease Pump optional range of couplers and extensions available fully repairable K45 Levergun wetted components: aluminium, steel and nitrile rubber output: up to kpa ( psi, 690 bar), 1.5 g per shot Accessories KZD Needlenose Coupler KZHY Hyperdermic Needlepoint coupler KFR Rigid/Flexible Extension KDF13 Flexible Extension KDF13 Flexible Extension 9

10 greasing equipment - hand operated grease pump J2 Grease pump J2B Bucket pump The J2 is a grease transfer pump designed for bulk filling grease dispensing equipment, and depending on model can fit pails from 12.5 kg (28 lbs) up to 22 kg (48 lbs), or with depths of 315 mm to 390 mm. The J2 is an ideal workshop complement combining economical bulk grease purchasing with the portability of a hand operated pump. handles up to and including NLGI No.2 greases suitable for refilling hand operated grease guns (K29, K32, K45, K40), air operated grease guns (K53, K54) and the 2.5 kg/5 kg Mini-Lube containers (KT5, KT6) includes pump unit, lid and rubber edged follower (all components are also available separately) J2B Bucket Pump has a 1.5 m (5 ft) x (1 2 ) ID delivery with hose (all components also available separately) and 1/4 BSP thread instead of the filler nozzle fully sealed to prevent contamination J2 Grease Pump wetted components: aluminium, steel, brass and nitrile rubber output: delivers 54 g per stroke Accessories GBP1 Grease Bearing Packer TR5 Trolley GBP1 Grease Bearing Packer 10

11 greasing equipment - air operated power-lube P3 The P3 is the ultimate in high pressure, air operated greasing. With models available to suit containers from 12.5 kg (28 lbs) to 22 kg (48 lbs), it is fitted with a 50:1 ratio air motor and can operate off most small compressors to provide fast, continuous greasing. suitable for underground coal mine use non-corroding air motor which operates quietly complete unit supplied with pump, lid, rubber edged follower plate, 4m (13 ft) x 6mm (1 4 ) ID SAE 100 R2 delivery hose, and B2 Booster Gun with 360 high pressure ZSB swivel (all components are available separately) handles up to and including NLGI No.2 greases optional trolley available (TR5) for a portable system no requirement for air line lubricator wetted components: zinc and hard chrome plated carbon steel, brass, and nitrile and polyurethane rubber output: approx. 460 g of NLGI No.2 grease per min. max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. compressor size: 0.08 m 3 /min (3 cfm) air inlet: 1 4 NPT (F) pump ratio: 50:1 (grease pressure is 50 times air) B2 gun pressure: up to kpa ( psi, 690 bar) (boost pressure) hose thread: 1 4 NPT (M) Accessories PDF13 Push On Extension PDF21 Push On Extension TA-4K Pressure Regulator Kit KZDXL Straight Needlepoint Coupler KRV Pressure Release Valve TA-4K Pressure Regulator Kit 11

12 greasing equipment - air operated maxi-lube P6 The P6 is a 50:1 ratio pump offering all the same features as the P3, yet has models available to suit grease containers from 50 kg (110lbs) to 55 kg (120lbs). suitable for underground coal mine use non-corroding air motor which operates quietly complete unit supplied with pump lid, rubber edged follower plate, 4 m (13 ft) x 6 mm (1 4 ) ID SAE 100 R2 delivery hose, and B2 Booster Gun with 360 high pressure ZSB swivel (all components are available separately) handles up to and including NLGI No.2 greases no requirement for air line lubricator optional trolley available (TR6) for a portable system wetted components: zinc and hard chrome plated carbon steel, brass, and nitrile and polyurethane rubber output: approx. 460 g of NLGI No.2 grease per min. max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. compressor size: 0.08 m 3 /min (3 cfm) air inlet: 1 4 NPT (F) pump ratio: 50:1 (grease pressure is 50 times air pressure) B2 gun pressure: up to kpa ( psi, 690 bar) hose thread: 1 4 NPT (M) Accessories TR6 Trolley PDF13 Push On Extension PDF21 Push On Extension TA-4K Pressure Regulator Kit KZDXL Straight Needlepoint Coupler KRV Pressure Release Valve TR6 Trolley 12

13 greasing equipment - air operated maxi-lube P8 A larger version of the P6, the P8 is a 50:1 ratio pump is designed to fit 180 kg (400 lbs) grease containers. suitable for underground coal mine use non-corroding air motor which operates quietly P8 complete unit includes the pump unit, lid, rubber edged follower plate, 2.5 m (8 ft) x 6 mm (1 4 ) ID delivery hose, and B2 Booster Gun with 360 high pressure ZSB swivel. lid and follower assembly available separately (P8LF) pump unit available separately (P8-01) a unique follower plate which incorporates a release valve and removal system includes bleeder valve for ease of priming when changing grease drums no requirement for air line lubricator handles up to and including NLGI No.2 greases wetted components: zinc and hard chrome plated carbon steel, brass, and nitrile and polyurethane rubber output: approx. 460 g of NLGI No.2 grease per min. max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. compressor size: 0.08 m 3 /min (3 cfm) air inlet: 1 4 NPT (F) pump outlet: 1 4 NPT (F) pump ratio: 50:1 (grease pressure is 50 times air pressure) B2 Gun pressure: up to kpa ( psi, 690 bar) hose thread: 1 4 NPT (M) Accessories PDF21 Push On Extension ACK2 Aviation Kit CK2 Industrial Greasing Accessory Kit TR205 Trolley TR6 Trolley 13

14 grease equipment - air operated high flow R5000G The R5000G is a 58:1 ratio pump designed to fit 180 kg (400lbs) grease container. It has a 4 air motor similar to R500 and R1000 pumps. This pump is ideal for inclusion into large system installations such as service bays. a strong metal 4 diameter air motor and durability proven in the R500 and R1000 series pump with silencer incorporated into the aluminium alloy pump body to ensure pump works quietly reduced ice build up in the air motor while running in the colder weather individual components include the pump unit (model R5000G), lid, rubber edged follower plate delivery hose and B2 booster gun with 360 high pressure ZSB swivel All of these are supplied when the R5000 GPLF is ordered. model R5000GLF contains lid and follower assembly only model R5000G is pump unit only a unique follower plate which incorporates a release valve and removal system. includes air line lubricator and preset air regulator 700 kpa (100 psi) handles up to and including NLGI No.2 grease 10 years parts availability wetted components: zinc and hard chrome plated carbon steel, nitrile and polyurethane rubber output: approx. 630 g of NLGI No.2 grease per min (free flow) max. air pressure: 700 kpa (100 psi, 7 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. compressor size: 0.22 m 3 /min (8 cfm) air inlet: 1 4 NPT (F) pump outlet 3/8 in BSPT or NPT pump ratio: 58:1 (grease pressure is 58 times air pressure) B2 Gun Pressure: up to kpa ( psi, 690 bar) 14

15 greasing equipment - air operated power-pistol K g (14.9 oz) cartridge K g (14.5 oz) cartridge The Power-Pistol is a single shot air operated grease gun providing the convenience of portability with effortless air operation. The gun is capable of operating at low air consumption, making it the ideal tool for use with trucks and buses utilising the air brake compressor. K53 Power-Pistol can be filled by bulk, cartridge or the J2 Grease Pump handles up to and including NLGI No.2 greases one handed, single shot trigger operation supplied with 230 mm (9") flexible extension (KF9) and KY coupler optional range of couplers and extensions available fully repairable wetted components: aluminium, steel, brass and nitrile rubber output: approx. 0.7 g per shot pressure ratio: 50:1 (grease pressure is 50 times air pressure) max. air pressure: 825 kpa (120 psi, 8 bar) (recommended is 620 kpa, 90 psi, 6 bar) min. air pressure: 275 kpa (40 psi, 2.75 bar) min. compressor size: m 3 /min (1 cfm) air inlet: 1 4 BSP (M) Accessories KZD Needlehose Coupler KZHY Hyperdermic Needlepoint Coupler KFR Rigid/Flexible Extension KFR Rigid/Flexible Extension 15

16 greasing equipment - battery powered powergun BG100 The BG100's unique design gives it balance, and makes routine greasing quicker and easier while reducing operator fatigue. It is ideal for any workplace environment where constant greasing and portability is required. BG100 Powergun ergonomic design simple one handed, trigger operation continuous operation and faster greasing models available to suit 400 g and 450 g cartridges supplied with a heavy duty moulded carrying case 30 (762 mm) flexible extension hose for greasing those hard to reach nipples several filling options available - bulk, cartridge or via the J2 grease pump fast battery recharge capability of just 1 hour from flat fitted with an internal pressure relief valve (12 months on battery and charger) 10 year guaranteed parts availability Accessories KZD Needlenose Coupler KZHY Hyperdermic Needlepoint Coupler KFR Rigid/Flexible Extension KSR/KGR Buttonhead Coupler wetted components: aluminium, steel and nitrile rubber output: 60 g (2.11oz)/min at free flow maximum pressure: kpa (5 000 psi, 345 bar) minimum temp: 0 C/32 F maximum temp: 50 C/122 F battery voltage: 12 volt NiCad battery capacity: 1300 mah est. battery life: up to 3 cartridges weight: 3 kg (6.6lbs) 16

17 greasing equipment - dispensing guns booster gun B2 pressurite gun KR suitable for air powered greasing applications supplied as a standard gun on the P3, P6 and complete grease pumps optional extra with P8 Maxi-Lube a couple of simple presses of the trigger will double output pressure supplied with 360 ZSB Swivel wetted components: mild steel and nitrile rubber max. operating pressure: kpa ( psi, 690 bar) swivel inlet: 1 4 NPT (F) Accessories PF9 Flexible Extension PF17 Flexible Extension suitable for manual powered greasing applications supplied with the K3 Super lube and K6 Mini lube can deliver grease at either high volume or high pressure suitable for greases up to and including NLGI No swivel to prevent hose kinking wetted components: aluminium, steel and nitrile rubber gun pressure: up to kpa ( psi, 690 bar) output: approx g on the high volume switch and approx 0.45 g on the high pressure switch (to clear a blocked or seized nipple) Accessories KF9 Flexible Extension/KDF13 Flexible Extension KZD Needlenose Coupler/KZHY Hyperdermic Needlepoint Coupler 17

18 fuel equipment - hand operated rapid-flo GP The GP is a durable, high quality impellor pump incorporating a gearbox for high output (up to 100 L per minute) and easy operation. Designed for 205 L (55 US g) or 60 L (16 US g) drums, this pump is ideal for any fuel transfer task. pumps diesel, petrol, av gas, kerosene and lubricating oils up to SAE 30 ideal for high volume aviation fuel transfer pumps easily in both directions supplied with a 2.4 m (8 ft) anti-static rubber delivery hose and nozzle, and 1.06 m (3.5ft) two piece threaded suction tube lockable handle and built-in nozzle holder in-built strainer 50 mm (2 ) bung adaptor optional 10 µm GB fuel filter available optional HNU nozzle for unleaded fuel wetted components: aluminium, steel, and nitrile and viton rubber output: up to 100 L (26 US g) per min. Accessories GB Fuel Filter DM100 Fuel Meter DG-01 Connector Kit HNU Nozzle GB Fuel Filter HNU Nozzle 18

19 fuel equipment - hand operated litre-stroke HP The HP Litre-Stroke has an easy lever action and is designed for either 205 L (55 US g) or 60 L (16 US g) drums. The pump is built for very harsh working conditions and is ideal for most types of fuel transfer operations when an economical and long lasting pump is required. pumps diesel, petrol, kerosene and lubricating oils up to SAE 30 supplied with a 2.4 m (8 ft) anti-static rubber delivery hose and HNU nozzle, and 1 m (3.3ft) two piece threaded suction tube lockable handle and built-in nozzle holder 50 mm (2 ) bung adaptor optional 10 µm HA fuel filter available wetted components: steel, acetal, zinc and nitrile rubber output: up to 40 L (10 US g) per min., or 1 L (1 quart) per stroke Accessories HAFuel Filter DM100 Fuel Meter DH-01 Connector Kit HA Fuel Filter DM100 Fuel Meter 19

20 fuel equipment - hand operated rotary booster pump RB This economical rotary pump is designed to reliably dispense various types of lubricating oils and fuels up to 75 L (20 US g) per minute from 60 L (16 US g) or 205 L (55 US g) drums. pumps diesel, petrol, kerosene and lubricating oils up to SAE 30 rotary action allows for pumping in both directions supplied with 1.8 m (6 ft) delivery hose with metal nozzle and nozzle holder the Rotary Booster is supplied with a three piece threaded suction tube and 2 sliding bung adaptor optional 10 µm VA fuel filter available separately wetted components: aluminium, steel, plastic and nitrile rubber output: up to 75 L (20 US g) per min., or 1 L (1 quart) per rotation. The 3:1 ratio gearing means that for every complete handle turn, the rotor turns 3 times outlet port: 25 mm (1") Accessories VA Fuel Filter DM100 Fuel Meter DV-01 Connector Kit VA Fuel Filter DM100 Fuel Meter 20

21 fuel equipment - hand operated rotary vane pump PVR Rotary Vane Pump PVRH Rotary Vane Pump with hose These economical rotary pumps are designed to dispense various types of lubricating oils and fuels up to 20 L (5 US g) per minute from 60 L (16 US g) to 205 L (55 US g) drums. pumps diesel, kerosene and lubricating oils up to SAE 90 rotary action allows for pumping in both directions supplied with a telescopic suction tube and a 2 sliding bung adaptor PVRH is supplied with a 1.8 m (6 ft) delivery hose with metal nozzle and nozzle holder optional 10 µm VA fuel filter available separately PVRH wetted components: aluminium, steel, plastic and nitrile rubber output: up to 20 L (5 US g) per min Accessories VA Fuel Filter DM100 Fuel Meter DV Connector Kit 21

22 fuel equipment - electric pumps electric diesel pump GE12M 12 V (Manual) GE12A 12 V (Automatic) GE24M 24 V (Manual) GE24A 24 V (Automatic) A reliable 12 or 24 volt range of quality pumps designed for the transfer of diesel and kerosene from storage tanks or drums into farm, transport and earthmoving vehicles. portable continuous duty cycle built-in fan self priming built-in pressure relief valve vane style pump consumption amps - 12 volt 9-17 amps - 24 volt detachable nozzle holder 3/4 BSP inlet/outlet thread 3 piece suction tube 3 m x 19 mm (3/4 ) outlet nose manual or automatic nozzle flowrate 50 L/min (free flow) GE12M Accessories TM100 Meter HA1S Filter DF-01 Connector Kit TM100 Fuel Meter 22

23 fuel equipment - electric pumps hi-flow electric diesel pump GEHFX 12M (Manual) GEHFX 12A (Automatic) A reliable 12 volt high flow diesel pump pump range designed to provide high flow diesel transfer. portable self priming built-in pressure relief valve continuous duty cycle built-in fan vane style pump consumption amps flowrate 75 L/min (free flow) key lock start 1 BSP inlet/outlet thread 1 I/O x 1.7 m long suction hose 1 I/O x 4 m long delivery nose manual or automatic nozzle weight 11.9 kg GEHFX 12M Accessories TM100 Meter HA1S Filter 23

24 fuel equipment - electric pumps hi-flow mini bowser GEMB240A This 240 volt hi-flow mini bowser is a complete refilling system designed for accurate hi-flow diesel refilling. cabinet flowmeter (accuracy +/-1%) automatic nozzle holder with built-in shut-off 4 m x 1 I/O delivery hose automatic nozzle built-in pressure relief valve vane style pump rated at IP55 flowrate 90 L/min thermal overload protection 24

25 oil transfer equipment - hand operated spring loaded pump S20H Spring Pump (20 L drums) S60H Spring Pump (60 L drums) S20HA Spring Pump with Filter (20 L drums) S60HA Spring Pump with Filter (60 L drums) The Spring Loaded Oil Pumps provide the means to automatically dispense engine and gear oils by simply pressing the oil gun trigger. suitable for engine and gear oils up to SAE 140 oil drain back facility on pump head kink resistant hose wetted components: aluminium, steel, zinc, brass, polypropylene, nitrile rubber and PVC output (20 L model): 340 ml per stroke (3 strokes per L) output (60 L model): 500 ml per stroke (2 strokes per L) S20H Accessories TR60 Trolley (60 L drums) TR6 Trolley (60 L drums TR5 Trolley (20 L drums) TR6 Trolley 25

26 oil transfer equipment - hand operated multi purpose pump A2 Multi purpose Pump A2H Multi purpose Pump with Hose A quality pump ideal for transferring a wide range of mineral oils and non-corrosive solvents. suitable to pump diesel fuel, lubricating oils up to SAE 90 and other noncorrosive fluids. A2H supplied with 1.8 m (6 ft) delivery hose and metal nozzle with the replacement o rings (nitrile, viton and EPDM) supplied with every pump, the pump can also be used to pump a wide range of non corrosive solvents and chemicals. To ascertain o ring compatibility, check our website, or speak with the liquid manufacturer (quoting the wetted components listed below) variable handle setting for light or heavy fluids telescopic suction tube fits 60 L (16 US gal) to 205 L (55 US gal) drums convenient bung opener cast on pump head fully serviceable wetted components: aluminium, steel, brass and Teflon output: approx. 250 ml per stroke A2H 26

27 oil transfer equipment - hand operated oil pumps C4 Oil Pump C4-Z Zinc Oil Pump C4H Oil Pump with Hose These fully serviceable, long life, low cost pumps have been engineered for trouble free use and can be used with a wide variety of non-corrosive liquids. Pump operates on the lift stroke. suitable for kerosene, two stroke mix and non-corrosive solvents up to SAE 30 sliding bung adaptors suit containers from 15 L (4 US g) to 25 L (6 US g) zinc versions are available for use in underground coal mines (C4-Z) C4H comes with 1.8 m hose and non-drip nozzle fully serviceable C4 wetted components: aluminium, steel, nitrile, delrin and zinc (C4-Z) output approx. 100 ml on the lift stroke C7 Oil Pump CF7 Oil Pump with Filter C7-Z Zinc Oil Pump CF7-Z Zinc Oil Pump with Filter These fully serviceable, long life, low cost pumps have been engineered for trouble free use and can be used with a wide variety of non-corrosive liquids. Pump operates on the downstroke. C7 suitable for kerosene, two stroke mix up to and SAE 140 sliding bung adaptors suit containers from 15 L (4 US g) to 25 L (6 US g) zinc versions are available for use in underground coal mines fully serviceable wetted components: aluminium, steel, nitrile, delrin and zinc (C7-Z and CF7-Z only) output: approx. 100 ml on the down stroke 27

28 oil transfer equipment - hand operated suction gun C16 The C16 is ideal for use with mineral oils to get them both into and out of gearboxes, transfer cases and differentials. Another useful application is to use the C16 to evacuate the sump of an inboard marine engine. C16 suitable for use with mineral oils up to SAE ml capacity gear oil pumps C11 Gear Oil Pump (205 L drums) C13 Gear Oil Pump (60 L drums) C13 These fully serviceable, long life, low cost pumps have been engineered for trouble free use specifically for heavy gear oils. ideal for pumping heavier gear oils up to SAE 140 supplied with a 1.8 m (6 ft) delivery hose with non drip nozzle and built-in hose hanger an optional CF strainer for auto transmission and hydraulic fluids also available wetted components: aluminium, steel, brass, nitrile and Teflon output: approx 75 ml per stroke accessories: cf strainer CF Strainer 28

29 specialty pumps - hand operated chemical lever pump PNY The PNY lever action chemical pump is manufactured from nylon 66 and provides a safe, economical and efficient means of transferring a wide range of fluids and chemicals. PNY 500 ml (1 Pint) per stroke telescopic suction tube designed to suit 60 L L containers lever action stainless steel chemical hand pump MCHP090D The MCHP090D Stainless Steel Hand Pump has been designed utilising stainless steel components and teflon seal. This allows the pump to be used to pump a wide range of fluids and chemicals. MCHP090D 400 ml per stroke delivers on up stroke sliding bung adaptor suitable for 60 L to 205 L containers materials 316 stainless steel teflon o ring seal chemical hand pump CHP The CHP hand pump is made from nylon with stainless steel plunger rod and teflon seals and is designed to transfer a wide range of fluids and chemicals. delivers 400 ml per stroke delivers on the up stroke sliding bung adaptor suitable for 60 L to 205 L containers CHP 29

30 oil transfer equipment - air operated oilmaster ratio oil pumps T112 The Oilmaster T112 is a reliable 1:1 ratio oil pump is designed to transfer oils up to 10 metres and can be used with any of Macnaught s hose end gun range. stub pump for inclusion in a workshop or mobile bulk oil system suitable for oils up to SAE 140, automatic transmission fluid, engine oil, gear oil and hydraulic oils 2 (M) bung adaptor supplied no requirement for air line lubricator optional TB25S telescopic suction tube available wetted components: aluminium, zinc and hard chrome plated carbon steel, brass, and nitrile and polyurethane rubber pump ratio: 1:1 (oil pressure is the same as air pressure) output: 27 L/min (7 US gal per min) of SAE 10 oil at 690 kpa (100 psi) air pressure (free flow) max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. air compressor: 0.3 m 3 /min, (10 cfm) air inlet: 1 4 NPT (F) pump inlet: 1 BSP or NPT (F) and 1 UNEF pump outlet: 3 4 BSP or NPT (F) Accessories TB25s Telescopic Suction Tube or TB26s TD20 Wall Bracket TA-4K Pressure Regulator Kit TB-20K Oil Feeder Hose Fluid Free flow (per min.) at Output (per min.) pump outlet through 3 m (10 ft) x 19 mm (3 4") hose, and hose end oil delivery gun Litres US Gal Litres US Gal Oil SAE Oil SAE Oil SAE *flow rates are a guide only and any variations can depend on system setup *flow rates at 690 kpa (100 psi) air pressure TD20 Wall Bracket 30

31 oil transfer equipment - air operated oilmaster ratio oil pumps T312 The Oilmaster T312 is a reliable 3:1 ratio oil pump is designed to transfer oils up to 30 metres and can be used with any of Macnaught s retractable reels and hose end gun range. stub pump for inclusion in a workshop or mobile bulk oil system suitable for oils up to SAE 140, automatic transmission fluid, engine oil, gear oil and hydraulic oils 2 (M) bung adaptor supplied no requirement for air line lubricator optional TB25S telescopic suction tube available wetted components: aluminium, zinc and hard chrome plated carbon steel, brass, and nitrile and polyurethane rubber pump ratio: 3:1 (oil pressure is 3 times the air pressure) output: 15 L/min (4 US gal per min) of SAE 10 oil at 690 kpa (100 psi) air pressure (free flow) max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. air compressor: 0.08 m 3 /min. (3 cfm) air inlet: 1 4 NPT (F) pump inlet: 1 BSP or NPT (F) and 1 UNEF pump outlet: 3 4 BSP or NPT (F) Accessories TB25s Telescopic Suction Tube or TB26s TD20 Wall Bracket TA-4K Pressure Regulator Kit TB-20K Oil Feeder Hose Fluid Free flow (per min.) at Output through 3 m (30 pump outlet ft) x 12.5 mm (1 2") hose, 10 m (33 ft) x 12.5 mm (1 2") hose reel and hose end oil delivery gun Litres US Gal Litres US Gal Oil SAE Oil SAE Oil SAE *flow rates are a guide only and any variations can depend on system setup *flow rates at 690 kpa (100 psi) air pressure TB20K Oil ZFeederhose 31

32 oil transfer equipment - air operated oilmaster ratio oil pumps T512 T512Z Zinc Version The Oilmaster T512 is a reliable 5:1 ratio oil pump designed to dispense lubricating oils up to 50 meters from bulk tanks or drums through pipelines, Macnaught s Retracta hose reels, and hose end delivery guns with or without a meter. stub pump for inclusion in a workshop or mobile bulk oil system suitable for oils up to SAE 140, automatic transmission fluid, engine oil, gear oil and hydraulic oils 2 (M) bung adaptor supplied no requirement for air line lubricator optional TB25S telescopic suction tube available wetted components: aluminium, zinc and hard chrome plated carbon steel, brass, and nitrile and polyurethane rubber pump ratio: 5:1 (oil pressure is the same as air pressure) output: 15 L/min (4 US gal per min) of SAE 10 oil at 690 kpa (100 psi) air pressure (free flow) max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. air compressor: 0.08 m 3, (3 cfm) air inlet: 1 4 NPT (F) pump inlet: 1 BSP or NPT (F) and 1 UNEF pump outlet: 3 4 BSP or NPT (F) Accessories TB25s Telescopic Suction Tube or TB26s TD20 Wall Bracket TA-4K Pressure Regulator Kit TB-20K Oil Feeder Hose Fluid Free flow (per min.) at Output (per min.) pump outlet through 9 m (30 ft) x 12.5 mm (1 2") hose, 10 m (33 ft) x 12.5 mm (1 2") hose reel and hose end oil delivery gun Litres US Gal Litres US Gal Oil SAE Oil SAE Oil SAE *flow rates are a guide only and any variations can depend on system setup *flow rates at 690 kpa (100 psi) air pressure TB25s Telescopic Suction Tube 32

33 oil transfer equipment - air operated r-series ratio oil pumps R100S stub pump R100T drum pump R100THG complete system The R100 is a 1:1 heavy duty ratio oil pump designed to transfer oils up to 10 metres and can be used with any of Macnaught s hose end gun range. suitable for oils up to SAE 140, automatic transmission fluid, diesel, kerosene, anti-freeze/anti-boil designed to fit from 60 L (16 US g) to 205 L (55 US g) drums (optional suction tube available for stub version) (TB17s) 2 (M) bung adaptor and oil lubricator supplied (TA-3K) the R1000THG (complete system) includes the R100T drum pump, 3 m (10 ft) reinforced delivery hose and trigger action dispensing nozzle R100S wetted components: aluminium, nitrile rubber, Carbon PTFE, zinc plated carbon steel and brass pump ratio: 1:1 (oil pressure is the same as air pressure) output: 60 L/min (16 US gal per min) of SAE 10 oil at 690 kpa (100 psi) air pressure (free flow) suction tube length: R100S (stub) 220 mm (83 4 ) R100T (drum) 910 mm (36 ) max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. air compressor: 0.22 m 3 /min (8 cfm) air inlet: 1 4 NPT (F) pump outlet: 3 4 BSP or NPT (F) foot valve inlet: 1 BSP or NPT (F) (stub only) Accessories TA-4K Pressure Regulator Kit TB17Ss Suction Tube TD20 Wall Bracket R100T Fluid Free flow (per min.) at Output (per min.) pump outlet through 3 m (10 ft) x 19 mm (3 4") hose and HG20R oil delivery gun Litres US Gal Litres US Gal Oil SAE Oil SAE Oil SAE Oil SAE Diesel Kerosene *flow rates are a guide only and any variations can depend on system setup *flow rates at 690 kpa (100 psi) air pressure TA-4K Pressure Regulator Kit 33

34 oil transfer equipment - air operated r-series ratio oil pumps R300S stub pump R300T drum pump The R300 is a 3:1 heavy duty ratio oil pump that can transfer oils up to 30 metres (98 ft) through multiple hose reels and meter/gun systems. suitable for oils up to SAE 140, automatic transmission fluid, diesel, kerosene, anti-freeze/anti-boil designed to fit from 60 L (16 US g) to 205 L (55 US g) drums (optional suction tube available for stub version) (TD42S) 2 (M) bung adaptor and oil lubricator supplied (TA-3K) the stub version (R300S) can be easily wall mounted R300S wetted components: aluminium, nitrile rubber, Carbon PTFE, zinc plated carbon steel and brass pump ratio: 3:1 (oil pressure is 3 times air pressure) output: 23 L/min (6 US gal per min) of SAE 10 oil at 690 kpa (100 psi) air pressure (free flow) suction tube length: R300S (stub) 210 mm (81 2 ) R300T (drum) 900 mm (351 2 ) max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. air compressor: 0.16 m 3 /min (6 cfm) air inlet: 1 4 NPT (F) pump outlet: 3 4 BSP or NPT (F) foot valve inlet: 3 4 BSP or NPT (F) (stub only) Accessories TD42S Suction Tube TD-25K Oil Feeder Hose OLP100 Low Pressure Oil Reel TD20 Wall Bracket R300T Fluid Free flow (per min.) at Output (per min.) pump outlet through 3 m (10 ft) x 19 mm (3 4") hose and 10 m (33ft) x 12.5 mm (1 2") reel & HG60 gun Litres US Gal Litres US Gal Oil SAE Oil SAE Oil SAE Oil SAE Diesel Kerosene *flow rates are a guide only and any variations can depend on system setup *flow rates at 690 kpa (100 psi) air pressure TB25s Telescopic Suction Tube 34

35 oil transfer equipment - air operated r-series ratio oil pumps R500S stub pump R500T drum pump The R500 is designed for workshops requiring fluid transfer over distances up to 50 metres. It is perfect for use with drums and tanks, and through pipelines, one or multiple hose reels and meter/gun dispensing systems. suitable for automatic transmission fluid, engine oil, gear oil, hydraulic oil, anti-freeze/anti-boil and compatible fluids up to SAE 140 suitable for 205 L (55 US g) drums and bulk tanks (optional telescopic suction tube available for stub version) (TB25S) the stub version (R500S) can be easily wall mounted built in pressure relief valve for safe operation oil lubricator (TA-3K) and 2 (M) bung adaptor supplied R500S wetted components: aluminium, nitrile rubber, Carbon PTFE, zinc plated carbon steel pump ratio: 5:1 (oil pressure is 5 times air pressure) output: 28 L/min (7 US gal per min) of SAE 10 oil at 690 kpa (100 psi) air pressure (free flow) dimensions: R500S (stub) 635 mm x 120 mm x 120 mm R500T (drum)1325 mm x 120 mm x 120 mm max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. air compressor: 0.28 m 3 /min (10 cfm) air inlet: 1 4 NPT (F) pump outlet: 3 4 BSP or NPT (F) foot value inlet: 1 BSP or NPT (F) and 1 UNEF (stub version) Accessories TB25S or TB26S Suction Tube Telescopic TA-4K Pressure Regulator Kit OMP100 Medium Pressure Oil Reel MOTP1920 Twin Pedestal Oil Reel R500T Fluid Free flow output Output (per min.) Output (per min.) (per min.) at the through 30 m (98 ft) x through 30 m (98 ft) x pump 10 mm (3 8") hose and 12.5 mm (1 2") hose hose end and hose end 690 kpa/100 psi (air) 690 kpa/100 psi (air) Litres US Gal Litres US Gal Litres US Gal Oil SAE Oil SAE Oil SAE *flow rates are a guide only and any variations can depend on system setup *flow rates at 690 kpa (100 psi) air pressure TB25s Telescopic Suction Tube 35

36 oil transfer equipment - air operated r-series ratio oil pumps R1000S stub pump R1000T drum pump The R :1 ratio oil ratio pump is the latest addition to the range and has been designed for workshops and systems requiring oil transfer of distances up to 100 metres. It is ideally suited for use with bulk tanks and drums and utilising multiple hose reels and meter/gun dispensing systems. suitable for automatic transmission fluid, engine oil, gear oil, hydraulic oil, anti-freeze/anti-boil and compatible fluids up to SAE 140 suitable for 205 L (55 US g) drums and bulk tanks (optional telescopic suction tube available for stub version) (TD42S the stub versions can be easily wall mounted built in pressure relief valve for safe operation oil lubricator (TA-3K) and 2 (M) bung adaptor supplied R1000S wetted components: aluminium, nitrile rubber, Carbon PTFE, zinc plated carbon steel pump ratio: 10:1 (oil pressure is 10 times air pressure) output: 15 L/min (4 US gal per min) of SAE 10 oil at 690 kpa (100 psi) air pressure (free flow) dimensions: R1000S (stub) 605 mm x 120 mm x 120 mm R1000T (drum) 1297 mm x 120 mm x 120 mm max. air pressure: kpa (150 psi, 10.3 bar) min. air pressure: 400 kpa (60 psi, 4 bar) min. air compressor: 0.50 m 3 /min (18 cfm) air inlet: 1 4 NPT (F) pump outlet: 3 4 BSP or NPT (F) foot value inlet: 3/4 BSP or NPT (F) (stub version) Accessories HGFEX Flexible Extension Multi coloured shrouds HGFM Flexible Metal Extension R1000T Fluid Free flow (per min) Output (per min.) at pump outlet through 35 m (115 ft) x 12.5 mm (1 2") hose and hose end 690 kpa/100 psi (air) Litres US Gal Litres US Gal Oil SAE Oil SAE Oil SAE *flow rates are a guide only and any variations can depend on system setup *flow rates at 690 kpa (100 psi) air pressure TA-4K Pressure Regulator 36

37 oil transfer equipment - oil control guns oil control gun HG20F HG20F Oil Control Gun with Flexible Outlet HG20R Oil Control Gun with Rigid Outlet These oil control guns are of high quality and easy to use in any workshop in conjunction with air operated oil systems up to 7:1 ratio (R100, R300, R500 and the Oilmaster pump range). dispenses lubricating oils up to SAE 140, and ethylene glycol (antifreeze/anti-boil) utilises a straight through flow path to reduce pressure drop latching trigger for ease of use incorporates a ball bearing swivel inlet to ensure smooth operation and prevent the hose from kinking non-drip automatic delivery nozzle trigger guard wetted components: aluminium, mild steel, nitrile rubber max. operating pressure: kpa (1000 psi, 70 bar) flow rate: up to 25 L/min (6.5 US gal per min) max. operating temp: 70 C (158 F) inlet connection: 1 2 BSP or NPT (F) weight (approx): 800 g (1.8 lbs) HG20R Accessories IM50 meter IM50 Meter 37

38 dispensing equipment - oil control guns high flow oil delivery gun HG100 Oil Delivery Gun HG100-Z Zinc Oil Delivery Gun HG Oil Delivery Gun with Electronic Flow Meter The HG100 is a feature packed high flow gun designed to shift large volumes of fluid quickly and easily. The gun is also available in zinc, for use in the mining industry. dispenses lubricating oils up to SAE 140, automatic transmission fluid, anti-freeze/anti-boil, and diesel oil flexible 3 4 ID hose with manual nozzle latching trigger for ease of use trigger guard for protection lockable trigger for anti-theft security hanging hook balanced valve assembly allows maximum flow control the HG includes an IM75 electronic oil meter HG100 wetted components: aluminium/zinc, mild steel, nitrile rubber flow rate: up to 57 L/min (15 US gal per min) max. operating pressure: kpa (1 500 psi, 103 bar) max operating temp: 70ºC (158ºF) inlet swivel: 3 4 BSP or NPT (F) weight (with fittings): 2.2 kg (5 lbs) HG

39 dispensing equipment - oil control guns mechanical hose end guns HG40 Manual Hose End Gun This popular model has an easy to read mechanical display and single reset button. dispenses up to 30 L/min (8 US gal per min) suitable for dispensing engine oil, diesel oil, automatic transmission fluid and anti-freeze/anti-boil, with a maximum viscosity of SAE 140 uses oval gear meter for optimum accuracy four digit resettable batch totaliser six digit accumulative totaliser automatic non drip nozzle latching handle with trigger lock (non latching model available) fully serviceable two outlet nozzle positions (in-line or 90 degrees) supplied complete with rigid extension shock resistant wetted components: aluminium, acetal, steel, nitrile rubber accuracy: +/- 1% (of reading) flow range: 1-30 L/min ( US gal/min) max. pressure: kpa (1 500 psi, bar) pressure loss: 100 kpa (14.4 psi, 1 12 L/min ( US gal/min) (without nozzle) with calibration... fluid weight: 1.16 kg (2.55 lbs) swivel inlet: 1 2" BSP or NPT (F) accessories: 25.8 cm (10") l x 9.5 cm (3.7") h x 11 cm (4.3") w Accessories HGFEX Flexible Extension Multi coloured shrouds HGFM Flexible Metal Extension HGFEX Flexible Extension 39

40 dispensing equipment - oil control guns mechanical hose end guns HG45 Auto Shutoff Hose End Gun Utilising the time proven oval gear principal of positive displacement fluid measurement, the HG45 Preset Mechanical is a highly accurate, metered control handle ideal for use in all automotive, transport and workshop installations dispenses up to 30 L/min (8 US gal per min) oval gear design settable volume up to 99.9 litres/us quarts easy to use thumbwheels for accurate volume setting - simply depress wheel and rotate able to set to decimal accuracy * easy to read 5 digit non-resettable total and 3 digit resettable batch total automatic non drip nozzle straight through flow path reduces pressure drop can be used without the preset function if required no batteries to fail simple handle latch design 10 year guarantee parts availability wetted components: aluminium, acetal, steel, nitrile rubber accuracy: +/- 1% (of reading) flow range: 1-30 L/min ( US gal/min) max. pressure: kpa (1 500 psi, bar) pressure loss: 100 kpa (14.4 psi, 1 12 L/min ( US gal/min) (without nozzle) with calibration... fluid weight: 1.16 kg (2.55 lbs) swivel inlet: 1 2 BSP or NPT (F) Accessories HGFEX Flexible Extension Multi coloured shrouds HGFM Flexible Metal Extension Multi Coloured Shrouds 40

41 dispensing equipment - oil control guns electronic hose end guns HG50 Alarm Hose End Gun dispenses up to 30 L/min (8 US gal per min) suitable for dispensing engine oil, diesel oil, automatic transmission fluid and anti-freeze/anti-boil, with a maximum viscosity of SAE 140. in addition to the standard manual and auto mode functions, there are five variable preset totals available for use uses oval gear meter for optimum accuracy three digit resettable batch totaliser six digit accumulative totaliser sleep mode; electronics go to sleep to preserve the life of the two standard AA batteries if the gun is not used for 2 minutes automatic non drip nozzle EEPROM retention allows all information to be retained if batteries are removed latching handle with trigger lock (non latching model available) fully serviceable two outlet nozzle positions (in-line or 90 degrees) supplied complete with rigid extension shock resistant wetted components: aluminium, acetal, steel, nitrile rubber accuracy: +/- 0.5% (of reading) flow range: 1-30 L/min ( US gal/min) max. pressure: kpa (1 500 psi, bar) pressure loss: 100 kpa (14.4 psi, 1 12 L/min ( US gal/min) (without nozzle) with calibration... fluid weight: 1.16 kg (2.55 lbs) swivel inlet: 1 2 BSP or NPT operating temp: 0-50 C ( F) storage temp: C ( F) battery: 2 x 1.5 volt alkaline AA Accessories HGFEX Flexible Extension Multi coloured shrouds HGFM Flexible Metal Extension HGFM Flexible Metal Extension 41

42 dispensing equipment - oil control guns electronic hose end guns HG55 Electronic Hose End Gun dispenses up to 30 L/min (8 US gal per min) suitable for dispensing engine oil, diesel oil, automatic transmission fluid and anti-freeze/anti-boil, with a maximum viscosity of SAE 140. uses oval gear meter for optimum accuracy three digit resettable batch totaliser six digit accumulative totaliser sleep mode; electronics go to sleep to preserve the life of the two standard AA batteries if the gun is not used for 2 minutes automatic non drip nozzle EEPROM retention allows all information to be retained if batteries are removed latching handle with trigger lock (non latching model available) fully serviceable two outlet nozzle positions (in-line or 90 degrees) supplied complete with rigid extension shock resistant wetted components: aluminium, acetal, steel, nitrile rubber accuracy: +/- 0.5% (of reading) flow range: 1-30 L/min ( US gal/min) max. pressure: kpa (1 500 psi, bar) pressure loss: 100 kpa (14.4 psi, 1 12 L/min ( US gal/min) (without nozzle) with calibration... fluid weight: 1.16 kg (2.55 lbs) swivel inlet: 1 2 BSP or NPT operating temp: 0-50 C ( F) storage temp: C ( F) battery: 2 x 1.5 volt alkaline AA Accessories HG FEX Flexible Extension Multi coloured shrouds HGFM Flexible Metal Extension Multi Coloured Shrouds 42

43 dispensing equipment - oil control guns electronic hose end guns HG60 Auto Shutoff Hose End Gun dispenses up to 30 L/min (8 US gal per min) suitable for dispensing engine oil, diesel oil, automatic transmission fluid and anti-freeze/anti-boil, with a maximum viscosity of SAE 140. uses oval gear meter for optimum accuracy in addition to the standard manual and auto mode functions, there are five variable preset totals available for use three digit resettable batch totaliser six digit accumulative totaliser sleep mode; electronics go to sleep to preserve the life of the two standard AA batteries if the gun is not used for 2 minutes automatic non drip nozzle EEPROM retention allows all information to be retained if batteries are removed latching handle with trigger lock (non latching model available) fully serviceable two outlet nozzle positions (in-line or 90 degrees) supplied complete with rigid extension shock resistant wetted components: aluminium, acetal, steel, nitrile rubber accuracy: +/- 0.5% (of reading) flow range: 1-30 L/min ( US gal/min) max. pressure: kpa (1 500 psi, bar) pressure loss: 100 kpa (14.4 psi, 1 12 L/min ( US gal/min) (without nozzle) with calibration... fluid weight: 1.16 kg (2.55 lbs) swivel inlet: 1 2 BSP or NPT operating temp: 0-50 C ( F) storage temp: C ( F) battery: 2 x 1.5 volt alkaline AA Accessories HGFEX Flexible Extension Multi coloured shrouds HGFM Flexible Metal Extension 43

44 flow meters - fuel meters fuel meter DM100 Flow Meter DM150 Flow Meter plus Filter The DM100 has been designed to measure diesel, kerosene and petrol, and is made from corrosion resistant aluminium with easy to read mechanical register. oval gear design low pressure drop allows for gravity and pump (in-line) applications register cap can be easily removed and rotated to every 90 orientation for display reading supplied with integrated mesh strainer DM100 wetted components: aluminium, zinc plated carbon steel, nitrile, viton accuracy: +/- 1% of reading flow range: 3-80 L/min ( US gal/min) max. pressure: kpa (145 psi, 10 bar) register totaliser: 0 999,999 L (gal) register reset: L (gal) max. temp: 80 C (176 F) inlet thread: 1 BSP or NPT (F) 1 BSPT, 1 BSPPL(G) or 1 NPT female outlet thread: 1 BSP or NPT (F) 1 BSPT, 1 BSPPL(G) or 1 NPT female weight: 1.2 kg (2.6 lbs) DM150 Accessories DF Connector Kit DM100 to GE12/24 Diesel pumps HA1S Filter DH Connector Kit - HP Pump DG Connector Kit - GP Pump DV Connector Kit - PVR/RB Pumps 44

45 flow meters - fuel meters turbine fuel meter TM100 (LCD) TM100P (Pulse Output) The TM100 turbine flowmeter has an excellent turndown ratio and is factory calibrated for precise measurement of low viscosity fluids. The low pressure drop and high pressure rating allows the turbine meter range to be used in gravity, pump and inline applications. available in LCD (TM100) and pulse (TM100P) versions high accuracy (better than ± 3 % of reading) excellent turndown ratio: 28:1 robust aluminium construction and fully sealed against dust and water splash flow linearisation (display version) field programmable easy to read and operate resetable six-digit display with ability to show batch, reset total, non-reset total and rate of flow average battery life 2 years (2 x AAA alkaline) protective boot standard on LCD version optional coloured boots available: red, blue, yellow, black and green. 10 year spare parts availability TM100 port Size: 1 BSPT / NPT wetted Materials: Aluminium, Tungsten, Ceramic, Derlin. maximum Pressure: 2070 kpa (300 psi, 20.6 bar) flow: 8 to 200 L/min (2.1 to 52.8 US gal/min) accuracy: better than ± 3 % of reading fluid compatibility: Diesel, kerosene, light oils TM100 LCD digits: 12 mm size and maximum of 6 digit display decimals: Selectable 0 to 3 totals: Batch / Reset Total / Non Reset Total / Rate temporary 5 0 C to 55 0 C TM100P Pulse operating Voltage: 12 to 30 V DC polarity protection: YES output: Open collector, maximum 1Watt peak (unfactored) connection: PCB terminal strip16 mm/1/2 NPT conduit temperature range 5 0 to 55 0 C TM100P TM100 45

46 flow meters - water meters turbine water meter TM100W (LCD) TM100WP (Pulse Output) The TM100W turbine flowmeter has an excellent turndown ratio and is factory calibrated for precise measurement of low viscosity fluids. The low pressure drop and high pressure rating allows the turbine meter range to be used in gravity, pump and inline applications. available in LCD (TM100W) and pulse (TM100W) versions high accuracy (better than ± 3 % of reading) excellent turndown ratio: 28:1 nylon construction and fully sealed against dust and water splash flow linearisation (display version) field programmable easy to read and operate resetable six-digit display with ability to show batch, reset total, non-reset total and rate of flow average battery life 2 years (2 x AAA alkaline) protective boot standard on LCD version optional coloured boots available: red, blue, yellow, black and green. 10 year spare parts availability TM100W port size: 1 BSPT / NPT, fully moulded wetted Materials: Nylon, Tungsten, Ceramic. maximum Pressure: kpa (150 psi, 10.3 bar) flow: 10 to 200 L/min (2.6 to 52.8 US gal/min) accuracy: better than ± 3 % of reading fluid compatibility: Water, Low viscosity fluids that does not attack Nylon TM100W LCD digits: 12mm size and maximum of 6 digit display decimals: Selectable 0 to 3 totals: Batch / Reset Total / Non Reset Total / Rate temperature range 5 0 C to 55 0 C TM100WP Pulse operating Voltage: 12 to 30 V DC polarity protection: YES output: Open collector, maximum 1Watt peak (unfactored) connection: PCB terminal strip16 mm/1/2 NPT conduit temperature range 5 0 to 55 0 C TM100WP 46

47 flow meters - oil meters oil meters IM50 (LCD) IM50P (Pulse Output) IM75 (LCD) IM75P (Pulse Output) The IM50 & 75 have been designed specifically to dispense lubricating oils, diesel and kerosene. These high pressure, positive displacement-type meter is suitable for all in-line and end-of-line applications and features a rugged and robust register with integrated electronics and large LC display. Robust aluminium construction and fully sealed against dust and water splash Easy to read and operate resetable six-digit display with ability to show batch, reset total, non-reset total and rate of flow User selectable display units: Litres, Gallons, Pints, Quarts Available with LC display or pulse output (pulse output model with 1 m fly lead available with either reed switch or hall effect sensor) Average battery life of two years (battery type: 2 x AAA alkaline) Protective boot standard on LCD version - optional coloured boots available: red, blue, yellow, green, black IM50 IM50/IM50P IM75/IM75P wetted components: acetal (suitable with oils), aluminium, PEI resin, aluminium, nitrile (NBR), nitrile (NBR), mild steel mild steel accuracy: ±0.5% of reading ±0.5% of reading flow range: 1-30 L/min ( US gal/min) 3-60 L/min ( US gal/min) max. working pressure: kpa (1 500 psi, bar) kpa (1 500 psi, bar) inlet thread: 1/2 BSPT or NPT (F) 3/4 NPT (F) outlet thread: 1/2 BSPT or NPT (F) 3/4 NPT (F) operating temperature: 5ºC (14ºF) to +55ºC (131ºF) 5ºC to 80 0 C for IM75P weight (approx): 430 g (0.95 lbs) 980 g (2.16 lbs) IM50P IM75 47

48 hose reels - retracta retracta auto rewind hose reels Retracta is the robust market leader in rewind hose reel systems. Retracta is the answer to storage and safety problems, and the wide range of models allows the reel to be used in any industry work environment. superior positive latching mechanism allows the reel to be mounted in any position weather resistant, high impact UV stabilised polypropylene safe storage system that keeps hoses off the floor versatile average weight with hose is 12 kg low rewind tension allows for easy hose pull out full stainless steel mouth for improved hose and reel service life lockable wall or overhead mounting bracket BU100 is supplied with every hose reel purchase and allows for hose reel rotation through 180 optional BB100 bench or floor mounting bracket is available separately an ability to have colour coded reels to suit any application or fit within an individual corporate look (conditions apply) fully repairable guaranteed availability of spare parts for 10 years Accessories BB100 Retracta Branch Bracket 48

49 Model Description Hose ID Hose Working Hose Material Reel Hose Max Working Reel Inlet Hose Outlet Weight Max. Length Pressure Colour Colour Temp. (BSP/NPT) (BSP/NPT) Viscosity AB100 air breathing 10 mm 17 m kpa (250 psi) reinforced PVC blue yellow 60 C 3/8 1/4 10 kg n/a AR100 compressed air 10 mm 20 m kpa (250 psi) reinforced PVC red red 60 C 3/8 1/4 10 kg n/a AR200 compressed air 12.5 mm 15 m kpa (250 psi) reinforced PVC red yellow 60 C 3/8 3/8 10 kg n/a AW100 compressed air/water 10 mm 20 m kpa (250 psi) reinforced PVC blue blue 60 C 3/8 1/4 10 kg n/a AW150 compressed air/water 10 mm 15 m kpa (250 psi) reinforced PVC blue blue 60 C 3/8 1/4 10 kg n/a AW200 compressed air/water 12.5 mm 15 m kpa (250 psi) reinforced PVC blue blue 60 C 3/8 3/8 10 kg n/a CW100 cold wash 12.5 mm 15 m kpa (150 psi) reinforced PVC blue white 60 C 3/8 hose nozzle 10 kg n/a DR100 garden water 12.5 mm 18 m 860 kpa (125 psi) reinforced PVC green green 60 C 3/8 hose nozzle 10 kg n/a FG100 food gas/co 2 6 mm 20 m kpa (250 psi) NTP red clear 60 C 3/8 1/4 10 kg n/a FR300 foam 16 mm 10 m kpa (150 psi) reinforced PVC white white 60 C 3/8 N/A 10 kg n/a GR100 grease 6 mm 10 m kpa (5000 psi) reinforced rubber black black n/a 1/4 1/4 13 kg n/a (SAE 100R2) HW100 hot water 12.5 mm 12 m kpa (200 psi) reinforced rubber red red 90 C 3/8 3/8 10 kg n/a HWP100* high pressure hot water 10 mm 12 m kpa (3000 psi) reinforced rubber red black 95 C 3/8 3/8 12 kg n/a (SAE 100 R2AT) OA100** oxy/acetylene 5 mm 15 m kpa (200 psi) reinforced rubber blue red/blue** n/a 5/8 UNF 5/8 UNF 13 kg n/a (AS 1335) OLPG100** oxy/lpg gas 5 mm 15 m kpa (200 psi) reinforced rubber black orange/blue** n/a 5/8 UNF 5/8 UNF 13 kg n/a (AS 1335) OLP100 low pressure oil 12.5 mm 10 m kpa (400 psi) reinforced rubber blue black 95 C 3/8 1/2 10 kg SAE 140 (SAE 100R6) OMP100 medium pressure oil 10 mm 10 m kpa (1000 psi) reinforced rubber blue black n/a 3/8 1/2 13 kg SAE 140 (SAE 100R1) PW100 potable water 12.5 mm 15 m kpa (150 psi) reinforced LDPE blue blue 60 C 3/8 3/8 10 kg n/a WP100 weedicide/pesticide 10 mm 16 m kpa (250 psi) reinforced PVC red red 60 C 3/8 1/4 10 kg n/a * HWP100 is not suitable for use with steam ** for OA100/OLPG100 are for Australian models only. BB100 49

50 hose reels - metal standard duty single pedestal range Macnaught standard duty metal hose reels are ideal for those applications where occasional use is normal. These reels are constructed in powder coated steel with a single pedestal and integral spring system. The stainless steel reel is bare, with a high polish finish and is ideal for highly corrosive environments. double supported steel drum shaft 4 bolt heavy duty steel mounting plate multi position ratchet for positive latching adjustable guide arm - can be wall, floor, ceiling, pit or vehicle mounted multi directional nylon roller guides reduce hose drag and wear lubricated spring encapsulated in cassette for safety full flow swivel for maximum product delivery external swivel for easy servicing of swivel seals MA1220 MG0615 SR0020 Model Description Hose ID Hose Length Working Pressure Hose Rewind Max Op Temp Reel Inlet Hose Outlet MA1020 Air/Water 10 mm (3/8") 20 m kpa (300 psi) Spring 80 ºC 3/8 BSP 3/8 BSP MA1220 Air/Water 12 mm (1/2") 20 m kpa (300 psi) Spring 80 ºC 1/2 BSP 1/2 BSP MO1220 Oil 12 mm (1/2") 20 m kpa (1000 psi) Spring 100 ºC 1/2 BSP 1/2 BSP MG0615 Grease 6 mm (1/4") 15 m kpa (5000 psi) Spring 100 ºC 1/4 BSP 1/4 BSP SR0020 Stainless 12 mm (1/2") Swivel Bare reel kpa (3000 psi) Spring N/A 1/2 BSP N/A 50

51 hose reels - metal heavy duty twin pedestal range Macnaught heavy duty hose reels are provided with twin pedestal supports and are particularly suitable for truck mount applications where stability and strength is required. All spring rewind models have an external spring cartridge allowing for easy maintenance and safety as the cartridge can be replaced without removing the reel from its mounted position. Constructed of powder coated steel with heavy duty swivel and a mechanism that allows for the hose to stop at any point. twin pedestal design for strength and stability - ideal for vehicle applications 4 bolt heavy duty steel mounting plate locking mechanism allows for precise hose length adjustment adjustable guide arm - can be wall, floor, ceiling, pit or vehicle mounted multi directional nylon roller guides reduce hose drag and wear external spring cartridge (except powered rewind diesel reel) for easy maintenance & safety full flow heavy duty swivel for maximum product delivery powder coated finish for corrosion resistance MDTP3820 MDTP2520 Model Description Hose ID Hose Length Working Pressure Hose Rewind Max Op Temp Reel Inlet Hose Outlet MDTP3820 Diesel 38 mm (1-1/2") 20 m kpa (500 psi) 24 V DC 80 ºC 1-1/2 BSP 1-1/2 BSP MDTP2520 Diesel 25 mm (1") 20 m kpa (500 psi) Spring 80 ºC 1 BSP 1 BSP MATP1220 Air/Water 12 mm (1/2") 20 m kpa (300 psi) Spring 80 ºC 1/2 BSP 1/2 BSP MATP1920 Air/Water 19 mm (3/4") 20 m kpa (300 psi) Spring 80 ºC 3/4 BSP 3/4 BSP MOTP1220 Oil 12 mm (1/2") 20 m kpa (1000 psi) Spring 100 ºC 1/2 BSP 1/2 BSP MOTP1920 Oil 19 mm (3/4") 20 m kpa (1000 psi) Spring 100 ºC 3/4 BSP 3/4 BSP MGTP0615 Grease 6 mm (1/4") 15 m kpa (5000 psi) Spring 100 ºC 1/4 BSP 1/4 BSP MGTP0915 Grease 9 mm (3/8") 15 m kpa (5000 psi) Spring 100 ºC 3/8 BSP 3/8 BSP WPTP1050 Weed/Pesticide 10 mm (3/8 ) 50 m kpa (500 psi) 24 V DC 80 ºC 3/8 BSP 3/8 BSP 51

52 oil and grease systems portable oil system OS100 The OS100 is a portable oil and grease system that caters for any workplace needs. All spare parts are available separately, and more information on a particular component from any of the systems is detailed separately in this catalogue. suitable for 205 L (55 US gal) drums TR205 drum trolley (wheel brake included) OLP100 low pressure (400 psi) Retracta hose reel - hose: 12.5 mm (1 2") I.D. x 10 m (32 ft) R300S 3:1 ratio stub pump bare system no hose end gun systems available complete with any hose end gun (HG40, HG45, HG50, HG55, HG60) telescopic suction tube with maximum depth of 1200 mm (4 ft) complete with 2 bung adaptor suction hose 1500 mm (5 ft) feeder hose 1000 mm (3 ft) OS100 HG40 HG45 HG50 52

53 oil and grease systems oil systems The OS500, OS600 & OS 800 systems are suitable for mounting onto IBC pods to create an easy to use and portable pumping system. OS500 mounting plate OLP100 low pressure (400 psi) Retracta hose reel - hose: 12.5 mm (1 2 ) I.D. x 10 m (32 ft) R300S 3:1 ratio stub pump HG50 electronic oil dispensing gun suction hose: 2 m x 3 4 feeder hose: 1 m x 1 2 OS600 mounting plate OLP100 low pressure (400 psi) Retracta hose reel hose: 12.5 mm (1 2 ) I.D. x 10 m (32 ft) R300S 3:1 ratio stub pump HG50 electronic oil dispensing gun oil lubricator air pressure regulator air pressure gauge quick connect air fittings suction hose: 2 m x 3 4 feeder hose: 1m x 1 2 OLP100 R300 OS500 Oil System OS800 mounting plate OMP100 medium pressure (1000 psi) Retracta hose reel - hose: 10 mm (3 8 ) I.D. x 10m (32 ft) T512 5:1 ratio oil pump HG55 electronic oil dispensing gun suction hose: 2 m x 3 4 feeder hose: 1 m x 1 2 HG50 53

54 oil and grease systems grease system P3-OS2 This portable grease system allows for pails up to 25 L (6 US g) to be placed inside the supplied 4 wheeled container. P3 Power-Lube grease pump complete with lid and follower assembly B2 Booster Gun complete with ZSB swivel (not shown) 1 4 NPT x 4 m high-pressure hose assembly four wheeled container with handle assembly and wheel lock pressure gauge pressure regulator grease system GS100 Compact, portable grease system designed to cater for any workplace needs. Spare parts and accessories are available separately. suitable for 180 kg (400 lbs) drums TR205 Drum Trolley (wheel brake included) GR100 Grease Reel P8 (50:1) Ratio Pump complete withlid and Follower B2 Booster Gun complete with ZSB swivel 10 year spare parts availability 54

55 oil and grease systems oil evacuation system OS250 The OS250 evacuation unit is suitable for use with engine oil, automatic transmission fluid and anti freeze/anti boil or compatible fluids. It can be used as a standard adjustable oil sump basin or as an air evacuation system. adjustable recovery basin pre - fill chamber 90 L (24 US g) drum metal and flexible probes gravity or air suction option ceevac The CEEVAC is a portable, compact and environmentally friendly evacuation unit. It has been designed to use the venturi principle to extract waste oil for safe disposal into any recycling container or bulk tank. the unique design does not allow for any oil spillage suitable for engine oil, ATF, anti-freeze and compatible fluids does not require air to remove the waste oil from the viewing tank easy to empty into a recyclable container or bulk waste unit comes complete with air gauge, air silencer, 2 plastic probes (not shown), 2 m suction hose, and the necessary quick connect fittings wetted components: aluminium, nitrile, plastic and brass oil removal: up to 2 L/min (depending on fluid viscosity) max. air pressure: 600 kpa (100 psi, 6 bar) max. oil temp: 80 C (176 F) 55

56 oil and grease systems fluid management and control system RN64 The Macnaught RN64 Fluid Management and Control System is a single or networked combination of 16 product controllers, with each controller supporting up to 4 colour touch-screens. Each controller can dispense up to 3 products simultaneously and be software configured to enable access to the products via any of the touch terminals. Software user friendly and easy to follow software installation process 3 level password access (manager, supervisor, operator) ensures appropriate security in maintaining fluid inventories automatic saving of batches with a presettable idle-time function simple and accurate transfer of data to a PC from the controller able to retain all records of fluid transfers (i.e. batches) from inventories even in the event of a power failure or a deliberate power-off by an operator software generates multiple reports that can be printed or exported to other software applications and can also be linked to proprietary accounting packages software incorporates a comprehensively secured inventory management system that facilitates standard accounting procedures Product designed to operate as either a stand alone controller or as part of a PC network up to 16 products per controller full colour, alpha numeric touch screen entry hierarchy Pin access for system users batch log storage of up to 300 batches product identification and name entry individual K factor on each product input meter selectable unit of measurement simple plug n play type field wiring and configuration can be used with any flowmeter compatible fluids visual alarms product tank inventory optional barcoding facility available for streamlining operations off-the-shelf system hardware ensures the latest technology and components are available worldwide 12 month warranty easily configured to fit different facilities RS485 network with optional USB converter or Ethernet server allowing distances of up to 1000 m touch screens powered over CAT 5 cable only standard power point required for each controller compatible with a wide selection of flowmeter and valve materials 56

57 Optional/special features: barcode/rfid large LCD remote display high waste level warning for each tank automatic ordering option available for each product remote interrogation and fault finding/troubleshooting remote operation for each dispense point if required Typical Applications: automotive workshops truck/bus/bulk transport workshops industrial workshops mining marine food processing plants breweries Typical fluids handled: motor oil automatic transmission fluid anti-freeze hydraulic oil fuel additives specialty fluids food oil chemicals viticulture/beverages Example of Standard Automotive Workshop Legend 1 Master PC/Printer A T and R Series 2 Shut-off Valve Oil Ratio Pumps 3 Strainer B MO1220 Metal Hose Reel 4 Positive Displacement C P8 Grease Lubricator M-Series Oil Meter D OMP100 Retracta Oil Reel 5 Solenoid Valve E HG20/HG100 Nozzle 6 Touch Screen 7 Remote LCD Display 3 variations of fluids are shown. Note: The RN64 has the capability of handling up to 16 products per controller. All control units are centralised back to network office PC for master control/inventory purposes. 57

58 accessories - grease fittings Button heads GBH1419B GBH1828B Button head grease fitting 1/4 x 19 BSPF (10 pack) Button head grease fitting 1/8 x 28 BSPF (10 pack) Grease nipples GN061M90 GN061MST GN081M90 GN081MST GN101M90 GN101MST GN1428S45 GN1428S90 GN1428SST GN1827N45 GN1827N90 GN1827NST Grease nipple M6 x 1 90 angle (10 pack) Grease nipple M6 x 1 straight (10 pack) Grease nipple M8 x 1 90 angle (10 pack) Grease nipple M8x 1 straight (10 pack) Grease nipple M10 x 1 90 angle (10 pack) Grease nipple M10 x 1 straight (10 pack) Grease nipple 1/4 28 SAE LT 45 angle (10 pack) Grease nipple 1/4 28 SAE LT 90 angle (10 pack) Grease nipple 1/4 28 SAE LT straight (10 pack) Grease nipple 1/4 28 NPT 45 angle (10 pack) Grease nipple 1/4 28 NPT 90 angle (10 pack) Grease nipple 1/4 28 NPT straight (10 pack) Easy out tool GNEL GNES Easy out tool - large Easy out tool - small GNES Grease nipple assortment pack GNP80M GNP80S Grease nipple assortment pack 80 piece metric Grease nipple assortment pack 80 piece SAE/NPT Refillable bearing lubricators MCGL 100(100mL) MCGL 220(220mL) The refillable automatic lubricators are high quality, mechanical, chemical and thermal resistant. Designed to provide constant lubrication to bearings, bushings, joints, articulated joints or wherever constant greasing is required. The lubricators are supplied with a setting dial which allows you to set the dispensing rate of the grease. GNP80s GNP80M manufactured from transparent Lexon setting dial (1,3,6 and 12 months) supplied with 2 springs, yellow (medium tension) black (strong tension) 58

59 accessories greasing kits ACK2 aviation kit Accessories typically required when lubricating aircraft. Items included are a KDN, KDS, KDE8, KDF21, KY, KZDXL, KZHY, KZLNJ, KZLNS, KZLNR, KZLN45, KZSNR and J65, with photos and descriptions of each included in this section. CK1 industrial greasing accessory kit An industrial workplace kit for users of air operated grease pumps. Items include a KDR, KGR, KSR, KZD, KDE8, PDF13 and PDF21, with photos and descriptions of each included in this section. CK2 industrial greasing accessory kit An industrial workplace kit for users of hand operated grease pumps. Items include a KDR, KGR, KSR, KZD, KDE8, KDF13 and KDF21, with photos and descriptions of each included in this section. FK1 farm greasing accessory kit An ideal kit for farmers who use air operated grease pumps. It includes a KDR, KGR, KSR, KZD, PDF13 and PDF21. Photos of each of these are included in this section. FK2 farm greasing accessory kit This kit is typically required by farmers who use hand operated grease guns. Items included are a KDF13, KDF21, KDR, KFR and KZD, with photos and descriptions of each included in this section. 59

60 accessories greasing couplers KY coupler Standard supergrip coupler supplied with all Macnaught grease guns. Designed to fit most grease nipples and grease guns. Can be purchased separately or in packets of 8 (KY-8). KDN right angle needlepoint coupler Ideal where access to the grease nipple is minimal. KDR right angle coupler For use in spaces when the area above the nipple is limited. KDS right angle coupler A slightly shorter version of the KDR. Along with the KDN and KDR, it can be used with a flexible extension. KSR standard buttonhead coupler For use on plant and machinery fitted with 5 8 buttonhead nipples. Length 72 mm (23 4 ). KGR giant buttonhead coupler For use on plant and machinery fitted with 7 8 buttonhead nipples. Length 85 mm (33 8 ). KRV pressure release valve Helps to prevent nipples from breaking off and couplers from splitting. Recommended for use with the K6 Minilube, P3 Powerlube, and P6 and P8 Maxilubes. KZD needlenose coupler Used when nipples are recessed and standard couplers would meet with interference from surrounding components (universal joints, etc). Length 93 mm (33 4 ). KZDXL straight needlepoint coupler Ideal for greasing the bearings on four wheel drive vehicles. Length 120 mm (43 4 ). KZE concave nipple coupler Used when vehicles are fitted with special nipples or, in some cases, when normal nipples are damaged. Length 60 mm (21 4 ). 60

61 accessories greasing couplers KZX concave nipple coupler KZLNR 90 needlepoint coupler A choice of four 30 cm straight needlepoint couplers. The first 3 are ideal for use with aircrafts, while the KZLNS can be used with four wheel drive vehicles. A similar coupler to the KZE but fitted with a rigid extension. Length 200 mm (8 ). KN grease injector needle Small needle used to inject sealed bearings and small lubrication points with grease when no grease nipples are present. Length 64 mm (21 2 ). KZHY hyperdermic needlepoint coupler Ideal for use on bearings fitted with rubber dust covers. Length 130 mm (51 8in). KZLN 45 needlepoint coupler KZLNS needlepoint coupler A choice of four 30 cm (12 ) straight needlepoint couplers. The first 3 are ideal for use with aircrafts, while the KZLNS can be used with four wheel drive vehicles. KZSNR 90 needlepoint coupler An 110mm (41 4 ) needlepoint coupler with a 90 bend at the end. ZSB swivel A 360 swivel supplied either separately or with the B2 Booster Gun. A choice of four 30cm straight needlepoint couplers. The first 3 are ideal for use with aircrafts, while the KZLNS can be used with four wheel drive vehicles. KZLNJ needlepoint coupler A choice of four 30 cm straight needlepoint couplers. The first 3 are ideal for use with aircrafts, while the KZLNS can be used with four wheel drive vehicles. 61

62 accessories grease extension hoses KDE8 extension A 220 mm (55 8 ) push on rigid extension coupler with a nipple to fit onto the KY coupler. For use with grease guns. KFR rigid/flexible extension A 330 mm (13 ) extension with a sliding sleeve that allows for either flexible or rigid operation. The thread is 1 8 BSP (M) and fitted with a KY coupler. air equipment PF9 flexible extension A 230 mm (9 ) high pressure flexible extension suitable for use with air operated greasing equipment. Its threads are 1 8 BSP (M). PF17 flexible extension This 430 mm (17 ) high pressure flexible extension is also suitable for air operated greasing equipment and has 1 8 BSP (M) threads. PDF13 push on extension A 330 mm (13 ) push on flexible extension for air operated equipment. Ideal for working in confined spaces. PDF21 push on extension A longer (530 mm or 21 ) version of the PDF13. PF6 extension hose A 4 m x 6 mm (1 4 ) ID high pressure extension hose for air operated greasing equipment. It is the standard supply with the P3 Power-Lube and the P6 Maxi-Lube, and has 1 4 NPT (M) threads. PF8 feeder hose A 2.5 m x 6 mm (1 4 ) ID high pressure feeder hose with 1 4 NPT (M) threads is also suitable for air operated greasing equipment, and is supplied when a complete P8 unit (P8-11) is ordered. manual equipment KF9 flexible extension A 230 mm (9 ) high pressure flexible extension suitable for Macnaught s manual grease gun range. It is supplied with the K29 Flexigun and K53 Power Pistol, and has 1 8 BSP threads. Can be purchased separately or in packets of 10 (KF9-10) KF17 flexible extension This 430 mm (17 ) high pressure flexible extension is also suitable for the manual grease gun range and has 1 8 BSP threads. 62

63 accessories manual equipment KDF13 flexible extension A 330 mm (13 ) push on flexible extension with nipple to fit the KY coupler. It is suitable for the manual grease gun range and is ideal for working in confined spaces. oil control gun accessories HGNZL automatic nozzle Fully automatic non-drip nozzle. KDF21 flexible extension A longer 530 mm (21in) version of the KDF13. HGFM flexible metal extension 300 mm (12 ) flexible set in place metal extension. air line accessories TA-3K lubricator kit An airline oil lubrication kit for use with the R-Series air powered oil pumps. The oil keeps the air motor free from corrosion and reduces seal wear. HGFNZ flexible extension 250 mm (10 ) flexible extension complete with fully automatic non-drip nozzle. HGREX rigid extension 150 mm (6 ) rigid extension. TA-4K pressure regulator kit This factory preset air pressure regulator can be used with the P3 Power-Lube, P6 Maxi-Lube and P8 Maxi-Lube grease pumps. Keeps air pressure at the ideal level for longer pump life. Preset to 862 kpa (125 psi, 8.6 bar). TA-5K Quick Release Coupler Kit A snap on connector for easy connection of air powered equipment to the airline. TA16 air valve A simple but very reliable on/off air valve for use with air operated grease and oil pumps. HGFEX flexible extension 250 mm (10 ) flexible extension. multi coloured shrouds HG range Manufactured from oil and shock resistant polyester, these colour coded shrouds provide extra protection to the oil control gun range. IM range Manufactured from oil and shock resistant polyester, these colour coded shrouds provide extra protection to the oil control gun range.z 63

64 accessories suction tubes oil feeder hoses TB17S suction tube A suction tube suitable for use with the R100S (stub) Ratio Oil Pump in drums and tanks to 1200 mm deep. Complete with 1 BSP fixing adaptor. TB23S suction tube This is the NPT version of the TB17S. TB25S suction tube A suction tube suitable for use with the pump models T112, T312, T512, R500S (stub) Ratio Oil Pumps in drums and tanks to 1200 mm deep. 1 UNF (M) thread. TB26S suction tube This suction tube has the same features as the TB25S, but has a foot valve included for when improved priming is required. TD42S suction tube A suction tube suitable for use with the R300S and R1000S (stub) Ratio Oil Pumps in drums and tanks to 1200 mm deep. Complete with 3 4 BSP fixing adaptor. TB-20K A 3 m (10 ft) high-pressure feeder hose suitable for use with the T512 Oilmaster pump. The hose has an I.D. of 12.5 mm (1 2 ) and a working pressure of kpa (1 000psi, 69 bar). TD-25K This 3 m (10 ft) low pressure feeder hose is ideal for use with the R100 and R300 ratio oil pumps, and the T312 Oilmaster pump. The hose has an I.D. of 12.5 mm (1 2 ) and a working pressure of kpa (400 psi, 28 bar). fuel filters GB fuel filter Supplied with fittings to suit the GP Rapid-Flo pump. Inlet: 1 NPT Outlet: 1 hosetail HA fuel filter Supplied with fittings to suit the HP Litre-Stroke pump. Inlet: 1 NPT Outlet: 1 hosetail TB24S suction tube This is the NPT version of the TD42S. VA fuel filter Supplied with fittings to suit the PVR, PVRH and RB pumps. Inlet: 1 NPT Outlet : 3 4 hosetail 64

65 accessories HA1S fuel filter Inlet thread: 1 NPT Outlet thread: 1 NPT HA7S filter element The 10 micron filter element used in the GB, HA and VA fuel filters. Supplied with seals. fuel nozzels CF strainer This 120 mm (43 4 ) fine mesh strainer can be used in conjunction with Macnaught s C-Series range of pumps (C7, C11 and C13) for pumping transmission fluids or hydraulic oils. The CF is included in the pump when the CF7 Oil Pump is ordered. fuel strainers Stainless steel mesh elements used in the GB, HA and VA fuel filters. HASS40 (40 mesh Stainless Steel) HASS80 (80 mesh Stainless Steel) DF Fittings for connecting DM 100/150 meters to GE12/24 fuel pumps. HNU nozzle Suitable for unleaded petrol, this 215 mm (81 2 ) fuel nozzle is designed to fit either the GP Rapid-Flo or the HP Litre-Stroke pumps. MCHP055 manual nozzle 21 mm diameter manual fuel nozzle. Flow rate up to 60 L/min (16 US gal/min). DG Fittings for connecting DM 100/150 meters to GP pumps. DH Fittings for connecting DM 100/150 meters to HP pumps. DV MCHP085 auto nozzle 21 mm diameter auto shut off fuel nozzle. Flow rate up to 70 L/min (18 US gal/min). MCHP070 auto nozzle 30 mm diameter hi flow auto shut off fuel nozzle. Flow rate up to 120 L/min (31 US gal/min). Fittings for connecting DM 100/150 meters to RB & PVR pumps.. 65

66 accessories trolleys TR5 trolley Designed to suit 15 L (4 US g) to 25 L (6 US g) oil, and 12.5 kg (28 lbs) to 22 kg (48 lbs) grease containers. TR6 trolley Designed to suit 50 L (13 US g) to 60 L (16 US g) oil, and 50 kg (110 lbs) to 55 kg (120 lbs) grease containers. TR60 trolley Designed to suit 50 L (13 US g) to 60 L (16 US g) oil drums. MCTR20 hand dolly Designed to suit drums up to 20 L / 18 kg. MCTR30 hand dolly Designed to suit drums up to 60 L / 55 kg. general accessories KT5 (2.5 kg) Grease Container KT6 (5 kg) Grease Container An optional grease container ideal for use in conjunction with the K6 Mini-Lube. Also available is the K6-24, a complete Mini- Lube system which includes the K6 and KT5 container. TR205 drum trolley Designed to suit drums up to 205 L (55 US g) or 180 kg (400 lbs), this drum trolley is ideal for use in portable oil or grease systems. 205HDL hydraulic drum trolley BB100 retracta bracket An optional bracket for mounting Retracta hose reels on a bench, floor or high wall. BU100 retracta bracket Standard bracket supplied with all Retracta hose reels for either wall or overhead mounting. Heavy duty hydraulic lift drum trolley designed to suit drums up to 205 L (55 US g) or 180 kg (400 lbs). 66

67 accessories GBP1 grease bearing packer Suitable for bearings with a minimum ID of 12 mm (1 2 ), maximum OD of 125 mm (5 ), and a height up to 50 mm (2 ) TD20 wall bracket A 2 wall mounting bracket for remote installations and suitable for use with all of Macnaught's air operated oil pumps OBTP pump mounted oil bar tap Suitable to use with R and T Series ratio oil pumps up tp kpa (800 psi, 55 bar) working pressure. In built strainer. OBTW wall mounted oil bar tap Suitable to use with R and T Series ratio oil pumps up tp kpa (800 psi, 55 bar) working pressure. In built strainer. GGH grease gun holder Designed to suit 15 L (4 US g) to 25 L (6 US g) oil, and 12.5 kg (28 lbs) to 22 kg (48 lbs) grease containers. DWA aluminium drum wrench Designed to suit 15 L (4 US g) to 25 L (6 US g) oil, and 12.5 kg (28 lbs) to 22 kg (48 lbs) grease containers. 67

68 OIL CONTROL GUNS MODEL EXTENSION TYPE METER FLOW RATE SAE30 OPERATING PRESSURE GUN WEIGHT HG20F Flexible No 25 L/min kpa (1 000 psi) 0.8 kg HG20R Rigid No 25 L/min kpa (1 000 psi) 0.8 kg HG100 Flexible No 57 L/min kpa (1 500psi) 2.2 kg HG40 (Mechanical Meter) Rigid Yes 30 L/min kpa (1 500psi) 1.1 kg HG50 (Electronic Meter) Rigid Yes 30 L/min kpa (1 500psi) 1.1 kg HG55 (Electronic Reset) Rigid Yes 30 L/min kpa (1 500psi) 1.1 kg HG60 (Electronic Preset) Rigid Yes 30 L/min kpa (1 500psi) 1.1 kg AIR OPERATED OIL PUMPS MODEL CONTAINER SIZE SUCTION TUBE** SUITABLE TO USE WITH FLOW RATE SUITABLE FOR (Free flow at the USE WITH pump with ATF) HOSE REEL Bulk tank* 205 L 60 L FIXED TELESCOPIC SAE 30 SAE 60 SAE 90 SAE 140 R100T Yes No 60 L/min x R100S * * No Yes 60 L/min x R300T Yes No 23 L/min R300S * * No Yes 23 L/min R500T Yes No 28 L/min R500S * * No Yes 28 L/min R1000T Yes No 15 L/min R1000S * * No Yes 15 L/min T112 Oilmaster * * * No Yes 27 L/min x T312 Oilmaster * * * No Yes 15 L/min T512 Oilmaster * * * No Yes 15 L/min * Refer to our catalogue or Macnaught reseller for correct suction tube selection ** To suit 60 L, 205 L or Tanks Note: It's always advisable to ensure the pressure rating of all plumbing, connections and hoses meet the standard required for the selected pump(s) and compressor combinations. HAND OPERATED OIL/FUEL PUMPS MODEL VOLUME CONTAINER SIZE FUEL SAE OIL OTHER NON- DELIVERY DELIVERED CORROSIVE HOSE/ LIQUIDS NOZZLE L 60 L 205 L tank PETROL DIESEL KEROSENE SAE 30 SAE 60 SAE 90 SAE m deep (LP) C4 Multi-Purpose# 100 ml/stroke x x x x x x x C4H Multi-Purpose# 100 ml/stroke x x x x x x C7 Oil Pump*# 100 ml/stroke x x x x C11 Gear Oil Pump* 75 ml/stroke x x x x x x C13 Gear Oil Pump* 75 ml/stroke x x x x x x A2 Multi Purpose 250 ml/stroke x x x A2H Pump 250 ml/stroke x x x GP Rapid-Flo** Up to 100 L/min x x x x x HP Litre Stroke** up to 40 L/min x x x x x Rotary Booster** up to 75 L/min x x x x x PVRH Rotary Pump** Up to 20 L/min x x x x PVR Pump** Up to 20 L/min x x x x x S20H/HA** 340 ml/stroke x x x x S60H/HA** 500 ml/stroke x x x x x C16 Suction Pump 500 ml/stroke x x x x x x x x * CF Strainer option available for auto transmission fluids ** Filter option available # Available in zinc for underground coal mining use. Modify suction tube to suit. 68

69 HAND OPERATED GREASE GUNS AND PUMPS TYPE FILLING METHOD 2.5 kg 20 kg PRESSURE CREATED VOLUME PER SHOT PUMPS NLGI (UP TO) #2 GREASES Cartridge Bulk J2 Pump K45/K45 Levergun Lever action kpa ( psi) 1.5 gms K29/K32 Flexigun* One hand operation kpa (7 500 psi) 0.68 gms K6/KR Minilube Manual/spring loaded lubrication x KT5 x kpa ( psi) High volume g KT6 on high pressure Container High pressure g K3/KR Superlube Manual/spring loaded lubrication x x x x kpa ( psi) High volume g on high pressure High pressure g J2 Grease Pump Fast and Easy loading of N/A x N/A 54 g/stroke KT5, K29 and K45 * model available in zinc for underground coal mining application AIR OPERATED GREASE GUNS AND PUMPS MODEL TYPE FILLING METHOD 20 kg 55 kg 180 kg 50:1 AIR PRESSURE PRESSURE CREATED* PUMP OUTPUT / VOLUME Cartridge Bulk J2 Pump Air Motor OPERATING RANGE (Up to) K53/K54 Single shot, x x x kpa kpa 0.68 g per shot Power Pistol single hand operation ( psi) (5 000 psi) P3 Powerlube 20kg librication system, x x x x x kpa kpa (5 000 psi) Typically 380 g/min portable with TR5 trolly ( psi) line pressure at 690 kpa (100 psi) kpa ( psi) using 4m x 6mm boost pressure hose with NLGI No.2. P6 Maxilube 55 kg lubrication system, x x x x x kpa kpa (5 000 psi) Typically 380 g/min portable with TR6 Trolley ( psi) line pressure at 690 kpa (100 psi) kpa ( psi) using 4m x 6mm boost pressure hose with NLGI No.2. P8 Maxilube 180 kg lubrication system, x x x x x kpa kpa (5 000 psi) Typically 380 g/min available as a complete unit ( psi) line pressure at 690 kpa (100 psi) or in component form kpa ( psi) using 4m x 6mm boost pressure hose with NLGI No.2. * With compressor at 690 kpa (100 psi) Macnaught's range of air operated pumps easily connect to any small compressor from 0.08 m 3 /min (3cfm) and are compatible to NLGI No. 2 Greases. A wide range of accessories are available - please refer to full Macnaught catalogue for all the details. The P3, P6 and P8 have no exposed aluminium and are suitable for underground coal mining. 69

70 HAND OPERATED GREASE GUNS AND PUMPS TYPE FILLING METHOD 2.5 kg 20 kg PRESSURE CREATED VOLUME PER SHOT PUMPS NLGI (UP TO) #2 GREASES Cartridge Bulk J2 Pump K45/K45 Levergun Lever action kpa ( psi) 1.5 gms K29/K32 Flexigun* One hand operation kpa (7 500 psi) 0.68 gms K6/KR Minilube Manual/spring loaded lubrication x KT5 x kpa ( psi) High volume g KT6 on high pressure Container High pressure g K3/KR Superlube Manual/spring loaded lubrication x x x x kpa ( psi) High volume g on high pressure High pressure g J2 Grease Pump Fast and Easy loading of N/A x N/A 54 g/stroke KT5, K29 and K45 * model available in zinc for underground coal mining application AIR OPERATED GREASE GUNS AND PUMPS MODEL TYPE FILLING METHOD 20 kg 55 kg 180 kg 50:1 AIR PRESSURE PRESSURE CREATED* PUMP OUTPUT / VOLUME Cartridge Bulk J2 Pump Air Motor OPERATING RANGE (Up to) K53/K54 Single shot, x x x kpa kpa 0.68 g per shot Power Pistol single hand operation ( psi) (5 000 psi) P3 Powerlube 20kg librication system, x x x x x kpa kpa (5 000 psi) Typically 380 g/min portable with TR5 trolly ( psi) line pressure at 690 kpa (100 psi) kpa ( psi) using 4m x 6mm boost pressure hose with NLGI No.2. P6 Maxilube 55 kg lubrication system, x x x x x kpa kpa (5 000 psi) Typically 380 g/min portable with TR6 Trolley ( psi) line pressure at 690 kpa (100 psi) kpa ( psi) using 4m x 6mm boost pressure hose with NLGI No.2. P8 Maxilube 180 kg lubrication system, x x x x x kpa kpa (5 000 psi) Typically 380 g/min available as a complete unit ( psi) line pressure at 690 kpa (100 psi) or in component form kpa ( psi) using 4m x 6mm boost pressure hose with NLGI No.2. * With compressor at 690 kpa (100 psi) Macnaught's range of air operated pumps easily connect to any small compressor from 0.08 m 3 /min (3cfm) and are compatible to NLGI No. 2 Greases. A wide range of accessories are available - please refer to full Macnaught catalogue for all the details. The P3, P6 and P8 have no exposed aluminium and are suitable for underground coal mining. 70

71 macnaught warranty 1. Macnaught Pty Ltd ( Macnaught ) warrants that all products manufactured by Macnaught and/or supplied by Macnaught under the Macnaught brand, excluding M-Series positive displacement meters ( Meters ) and components subject to wear, will be free from any defects caused by faulty materials or workmanship for a period of 5 years from the date of purchase of the product. 2. For Meters, the warranty period is 12 months from the date of purchase of that product. 3. For components contained in all products (including Meters) which are usually subject to wear from normal operation of the products (such as o-rings, seals, springs and hoses), the warranty period is 12 months from the date of purchase of the relevant product. 4. For products and components which are not manufactured by Macnaught and are supplied by Macnaught under a brand name other than Macnaught, the warranty period is the longer of 12 months from date of purchase of the relevant product and the period of the manufacturer s warranty. 5. The warranties contained in clauses 1, 2, 3 and 4 above are conditional on the Purchaser, during the relevant warranty period: a. delivering to Macnaught a detailed notice setting out full details of any defect in any Product and details of the date and place of purchase (together with copies of purchase receipts and/or other supporting documents); and b. at the purchaser s own cost, returning the defective Product to the nearest authorized Macnaught service centre. 6. Subject to compliance by the purchaser with clause 5, Macnaught shall, at its option, repair or replace any product or component found defective by its inspection by reason of faulty materials or workmanship of Macnaught. 7. This warranty does not cover failure of products, parts or components which, in the sole judgment of Macnaught, arises other than from faulty materials or workmanship of Macnaught, including misuse, abrasion, corrosion, negligence, accident, substitution of non-macnaught parts, unauthorized modification, improper use, storage or handling, faulty installation or tampering by the purchaser or any third party. 8. If Macnaught inspection discloses no defect in material or workmanship, repair or replacement and return (at Macnaught s sole option) will be made at customary charges, which will be advised to the purchaser. 9. Macnaught s liability and the purchaser s rights under this Warranty shall be limited to repair or replacement of defective products or components and in particular, shall not extend to any direct, special, indirect or consequential damage or losses of any nature. 10. The foregoing warranty supersedes, voids and is in lieu of all or any other warranties. This warranty does not form part of, nor does it constitute, a contract between Macnaught and the end-user or purchaser. It is additional to any warranty given by the seller of the products. This warranty does not exclude, limit, restrict or modify the non-excludable rights or remedies conferred upon the end-user or purchaser, or the non-excludable duties or liabilities imposed on the seller or Macnaught, by Part V, Divisions 2 and 2A of the Trade Practices Act 1974 (Commonwealth) or other legislative provisions. Macnaught otherwise excludes, to the extent permitted by law, any rights conferred on the

72 Head Office - Sydney Macnaught Pty Ltd Henderson St, Turrella Sydney NSW 2205 Australia Ph: Fax: info@macnaught.com.au website: Quality Endorsement applicable to Macnaught Head Office Sydney Only Macnaught Asia Macnaught Asia Pte Ltd 20 Kallang Av. #03-00 Pico Creative Centre, Singapore, Ph: Fax: Sales Representative Office (Jakarta) Ph: Fax: sales@macnaughtasia.com.sg website: Macnaught USA Macnaught USA, Inc. 614 South Ware Boulevard Dock 14A (for deliveries) Tampa, FL Ph: Fax: info@macnaughtusa.com website: Macnaught Europe Macnaught Europe Ltd D1 Lincoln Park Borough Road Buckingham Road Ind Est Brackley NN13 7BE United Kingdom Ph: Fax: info@macnaughteurope.com website: Available from: macnaught.com.au