Specifications & Installation Instructions

Transcription

1 & Installation Instructions 1206 M Avenue Kearney, NE P: F: TaskLighting.com

2 TR Series Angle Power Strip Tamper Resistant Duplex Receptacles eliminate cutouts for receptacles and switches in your backsplash TR Series Angle Power Strip Part Number Length # of Duplex Recept. Recept. Color Finish TR9-1ColorD-P-Finish 9" 1 B, G, W, BZ, TABLE OF CONTENTS TR Series Angle Power Strip...pg. 3-4 TR Series Angle Power Strip Custom Options...pg. 5 TR-USB Series Angle Power Strip...pg. 6-7 TR/TR-USB Series Angle Power Strip Installation Instructions...pg. 8 APT Series Angle Power Strip...pg APT Series Angle Power Strip Installation Instructions...pg. 11 Lighted Power Strip DV Series...pg Lighted Power Strip DV Series Installation Instructions...pg Lighted Power Strip RM Series...pg Lighted Power Strip RM Series Installation Instructions...pg. 18 semprialed SG9 Series...pg. 19 semprialed SG9 Series Installation Instructions...pg semprialed A Series...pg. 22 semprialed F Series...pg. 23 SsempriaLED A & F Series Installation Instructions...pg semprialed R Series...pg. 26 semprialed R Series Installation Instructions...pg semprialed S Series...pg. 29 semprialed S Series Installation Instructions...pg semprialed Lighted Closet Rod...pg. 32 semprialed Lighted Closet Rod Installation Instructions...pg. 33 semprialed Puck...pg. 34 semprialed Mini Can...pg. 35 semprialed Puck/ Mini Can Installation Instructions...pg. 36 semprialed Supporting Products...pg. 37 semprialed 120V Bar Light...pg. 38 semprialed 120V Bar Light Installation Instructions...pg. 39 Tamper Resistant Duplex Receptacles Easy Installation Designer finishes to blend with any decor 3-Year Limited Warranty Custom options include: USB Ports, Phone Jacks, Cable Jacks, Data Ports. See pg. 5 for more options. Kitchens Baths Offices & Computer Labs Islands Shops & Garages Construction Materials: 2-1/8" 7/8" Section Drawing Powder Coated Aluminum 120V 2-1/4" 2- Wood Screws & Wall Anchors TR12-1ColorD-P-Finish 12" 1 B, G, W, BZ, TR18-2ColorD-P-Finish 18" 2 B, G, W, BZ, TR24-2ColorD-P-Finish 24" 2 B, G, W, BZ, TR30-2ColorD-P-Finish 30" 2 B, G, W, BZ, TR36-2ColorD-P-Finish 36" 2 B, G, W, BZ, TR42-3ColorD-P-Finish 42" 3 B, G, W, BZ, TR48-3ColorD-P-Finish 48" 3 B, G, W, BZ, TR60-4ColorD-P-Finish 60" 4 B, G, W, BZ, TR72-4ColorD-P-Finish 72" 4 B, G, W, BZ, Finish Options Black () Bronze (BZ) Satin Nickel (SN) White () Receptacle Colors Black (B) Gray (G) White (W) Optional Installation Components DIMENSIONS TR-SQ-JB-P-Finish 3" x 3" x 2-1/8" Square Junction Box 12 ga. Romex Dry Only TR-SPEC

3 TR Series Angle Power Strip Tamper Resistant Duplex Receptacles Installed view TR Series Angle Power Strip Custom Options TR Series Custom Options TR72-4ColorD-Finish 72" 14-1/4" 14-1/4" 14-1/4" 14-1/4" 14-1/4" Switches CUSTOM LENGTHS Custom lengths to the 1/4 from - 92" (larger sizes will have a seam when assembled) SWITCHES 60" 48" TR60-4ColorD-Finish 12" 12" TR48-3ColorD-Finish 12" 12" 12" 12 " 12 " 12" 12" TRO-DS-2SPS-W Receptacles TRO-15A-REC TRO-3WS,TRO-4WS, TRO-SPS TRO-20A-REC COLOR TRO-SPS-Color Decora single-pole rocker switch B, G, W TRO-SPS-20A-Color Decora 20 Amp single-pole rocker switch B, G, W TRO-3WS-Color Decora 3-way rocker switch B, G, W TRO-3WS-20A-Color Decora 20 Amp 3-way rocker switch B, G, W TRO-4WS-Color Decora 4-way rocker switch B, G, W TRO-DS-2SPS-Color Decora double switch B, G, W TRO-DS-(2)3WS-Color Double switch with (2) 3-way B, W TRO-DS-1P/3P-Color Double switch with single-pole & 3-way B, G, W TR42-3ColorD-Finish 42" TR36-2ColorD-Finish 36" TR30-2ColorD-Finish 30" TR24-2ColorD-Finish 7-9" 7-24" TR18-2ColorD-Finish 6" 6" 6" 18" TR12-1ColorD-Finish 6" 6" 12" TR9-1ColorD-Finish 9" 10" 11" 11" 10" 12" 12" 12" 10" 10" 10" 4-4- Legend = Knock-out (all knock-outs are from end) Custom Options = Receptacle (15A receptacle standard) Custom lengths from - 92" (sizes over 92" will have a seam when assembled) Additional devices (see page 5) Custom device placement Custom Option Details Receptacles must be a minimum of 5" apart (on center) Receptacles must be a minimum of 3" from the end Custom charges will apply, call for a quote and assistance with your custom order Call for lead time Combination Devices Connectors TRO-PJ Port Frames TRO-CON-CJ Power Supply TRO-CJ TRO-2PORT, TRO-3PORT, TRO-4PORT & TRO-6PORT Snap-in Connectors TRO-CON-HDMI TRO-USB/REC TRO-TLD-D30WSO TRO-TLD-D45WSO TRO-TLD-D60WSO TRO-TLD-D75WSO TRO-CON-PJ TRO-CON-BLANK TRO-LPV TRO-CB-IP/REC & TRO-CB-3P/REC TRO-HDMI TRO-CON-CAT6 TRO-TS-3SPS-Color Decora triple switch w/ three single-pole switches B, W RECEPTACLES TRO-15A-REC 15 Amp tamper resistant receptacle B, G, W TRO-20A-REC 20 Amp tamper resistant receptacle B, G, W RECEPTACLES/SWITCH COMBO TRO-USB/REC Combination (2) USB ports and receptacle B, G, W TRO-CB-1P/REC-Color Combination single-pole switch and receptacle B, G, W TRO-CB-3P/REC-Color Combination 3-way switch & receptacle B, G, W CONNECTORS TRO-CJ-Color Decora style Cable Jack, "F" Style, for 75 Ohm coaxial cable B, G, W TRO-PJ-Color Decora style 6 conductor telephone jack B, G, W TRO-HDMI-Color HDMI Port Connector W PORT FRAMES TRO-2PORT-Color TRO-3PORT-Color TRO-4PORT-Color TRO-6PORT-Color SNAP-IN CONNECTORS TRO-CON-BLANK-Color TRO-CON-CAT6-Color Decora style multimedia insert. Allows you to combine your choice of 2, 3, 4, or 6 voice, data, audio, or video connectors into one compact, attractive wallplate Blank insert used to cover up any unused openings in any of the Port Frames Snap-in Data Category 6 8-conductor component-rated connector. 250 MHz B, G, W B, G, W B, G, W TRO-CON-CJ-Color Snap-In cable jack. B, G, W TRO-CON-PJ-8-Color 6-conductor USOC voice grade phone (jack) connector B, G, W TRO-CON-HDMI-Color HDMI feed through Quick Port Connector B, W POWER SUPPLIES TRO-TLD-D30WSO TRO-TLD-D45WSO TRO-TLD-D60WSO TRO-TLD-D75WSO TRO-LPV-20W-15V TRO-LPV-35W-15V 15V DC 30W hardwire 15V DC 45W hardwire 15V DC 60W hardwire 15V DC 75W hardwire 15V DC 20 Watt LED power supply (use with wireless dimming system) 15V DC 35 Watt LED power supply (use with wireless dimming system) 4 TR-SPEC-0618 TR-CUSTOM

4 TR-USB Series Angle Power Strip Tamper Resistant Receptacles with USB included TR-USB Series Angle Power Strip Tamper Resistant Receptacles with USB included Installed view Part Number Length # of USB/ Recept. Combo # of Duplex Recept. Recept. Color Finish TRU72-4ColorD-Finish 72" 14-1/4" 14-1/4" 14-1/4" 14-1/4" 14-1/4" TRU9-1ColorD-P-Finish 9" 1 B, G, W TRU12-1ColorD-P-Finish 12" 1 B, G, W TRU18-2ColorD-P-Finish 18" 1 1 B, G, W, BZ,, BZ,, BZ, TRU60-4ColorD-Finish 60" 12" 12" 12" 12 " 12" 2-1/4" TRU24-2ColorD-P-Finish 24" 1 1 B, G, W TRU30-2ColorD-P-Finish 30" 1 1 B, G, W, BZ,, BZ, TRU48-3ColorD-Finish 48" 12" 12" 12 " 12" 2-1/8" 2- TRU36-2ColorD-P-Finish 36" 1 1 B, G, W TRU42-3ColorD-P-Finish 42" 1 2 B, G, W TRU48-3ColorD-P-Finish 48" 1 2 B, G, W, BZ,, BZ,, BZ, 42" TRU42-3ColorD-Finish 10" 11" 11" 10" 7/8" Section Drawing TRU60-4ColorD-P-Finish 60" 1 3 B, G, W TRU72-4ColorD-P-Finish 72" 1 3 B, G, W, BZ,, BZ, TRU36-2ColorD-Finish 36" 12" 12" 12" USB device always positioned on left Tamper Resistant Easy Installation Designer finishes to blend with any decor 3-Year Limited Warranty Finish Options TRU30-2ColorD-Finish 30" 10" 10" 10" Black () Bronze (BZ) Receptacle Colors Satin Nickel (SN) White () TRU24-2ColorD-Finish 7-9" 7-24" Kitchens Baths Offices & Computer Labs Islands Shops & Garages Construction Materials: Powder Coated Aluminum 120V Wood Screws & Wall Anchors 12 ga. Romex Dry Only Black Gray White USB/Receptacle Combo Colors Black Gray White Optional Installation Components DIMENSIONS TR-SQ-JB-P-Finish 3" x 3" x 2-1/8" Square Junction Box TRU18-2ColorD-Finish 6" 6" 6" 18" TRU12-1ColorD-Finish 6" 6" 12" TRU9-1ColorD-Finish 9" 4-1/4" 4-1/4" Legend = Knock-out (all knock-outs are from end) = Receptacle (15A receptacle standard) = USB/ Receptacle Combo (15A receptacle standard) 6 TRU-SPEC-0618 TRU-SPEC

5 TR/TR-USB Series Angle Power Strip Installation Instructions APT Series Angle Power Strip Tamper Resistant Receptacles eliminate cutouts for receptacles and switches in your backsplash General Guidelines Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at APS. All wiring must meet NEC and local codes. The Angle Power Strip (APS) must be installed by a licensed electrician. Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed. Part Number Length # of Recept. Recept. Color Finish APT9-2Color-P-Finish-*Position 9" 2 B, G, W, BZ, APT12-2Color-P-Finish-*Position 12" 2 B, G, W, BZ, APT18-3Color-P-Finish-*Position 18" 3 B, G, W, BZ, W2436 Valance W1836 W2436 APT24-4Color-P-Finish 24" 4 B, G, W, BZ, 2 APT30-4Color-P-Finish 30" 4 B, G, W, BZ, Angle Power Strip- TR Series 3 (Max. 15 Amps) (Piece B) Wire Entry Wire Entry Romex (Max. 15 Amps) (Piece A) 3 Wire Entry 12-2 Romex Angle Power Strip-TR Series 1-11/16" 1-5/8" APT36-4Color-P-Finish 36" 4 B, G, W, BZ, APT42-5Color-P-Finish 42" 5 B, G, W, BZ, APT48-5Color-P-Finish 48" 5 B, G, W, BZ, APT60-7Color-P-Finish 60" 7 B, G, W, BZ, 3/4" APT72-8Color-P-Finish 72" 8 B, G, W, BZ, GFCI 1 Turn power off! Section Drawing *Indicate Left (L) or Right (R) side wire entry To electrical panel Tamper Resistant Easy Installation Designer finishes to blend with any decor 3-Year Limited Warranty Finish Options Black () Bronze (BZ) Satin Nickel (SN) White () Kitchens Baths Offices & Computer Labs Islands Shops & Garages Receptacle Colors Black (B) Gray (G) White (W) 1 Turn power off at panel. Carefully pry 2 Secure APS TR Series to wall with 3 To terminate last APS- TR Series, open each piece with tool (provided). Insert screws into each stud or use anchors use wire nuts on ends of wires. Romex connector into hole. Pull wires into provided. Strip wires and connect Snap cover in place, and turn power APS-TR Series. BLACK wire from romex to GOLD on. Firmly insert plug straight into terminal and WHITE wire from romex receptacle, applying equal pressure to SILVER terminal. Ground all GREEN to both blades at the same time. wires to PEM studs inside of back frame. Gently rock plug, if needed. When connecting two APS TR Series, run Romex from piece A to piece B. Ground each section to the next. Construction Materials: Powder Coated Aluminum 120V Wood Screws & Wall Anchors 12 ga. Romex Dry Only Optional Installation Components DIMENSIONS SQ-JB-Finish 3 x3 x 1-1/2 Square Junction Box 8 TR-INSTALL-0618 APT-SPEC

6 APT Series Angle Power Strip Installed view APT Series Angle Power Strip Installation Instructions 72" 60" 7-1/8" 8-1/4" 8-1/4" 8-1/4" 8-1/4" 8-1/4" 8-1/4" 8-1/4" 7-1/8" General Guidelines Power source MUST be a 20 Amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at APS. All wiring must meet NEC and local codes. The Angle Power Strip (APS) must be installed by a licensed electrician. Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed. W2436 Valance W1836 W " " APS 3 (Piece B) Wire Entry Wire Entry Romex (Piece A) Wire Entry 12-2 Romex APS 36" 7-1/8" 7-1/4" 7-1/4" 7-1/4" 7-1/8" Legend = Knock-out (all knock-outs are from end) GFCI 1 Turn power off! 30" 7-1/8" 5-1/4" 5-1/4" 5-1/4" 7-1/8" = Receptacle (Available in Black, Gray, or White) Custom Options Custom lengths from 6" - 92" (larger sizes will have a seam when assembled) To electrical panel 24" 7-1/8" 3-1/4" 3-1/4" 3-1/4" 7-1/8" 120 Volt integral switch (available in black or white only) Additional receptacles 18" 12" 9" " 5" 2" 2" 2-2- Custom receptacle/switch placement Custom Option Details Receptacles must be a minimum of apart (on center) Receptacles must be a minimum of 1" from end. (Requires wire entry at opposite end of fixture) Custom charges will apply. Call for a quote and assistance with your custom order. Call for lead time 1 Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into hole with locknut on back frame. Pull wires into APS. 2 Secure APS to wall with screws into studs or use anchors provided. Strip wires and connect BLACK to BLACK, WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame. When connecting two APS, run Romex from fixture to fixture. Ground each section to the next. 3 To terminate last APS, use wire nuts on ends of wires. Snap cover in place and turn power on. Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed. 10 APT-SPEC-0618 APT-INSTALL

7 Lighted Power Strip DV Series for LPS WITH Built-In Driver Lighted Power Strip DV Series for LPS WITH Built-In Driver Installed view 2-5/8" 1" 1-5/8" WITH Built-In Driver and Switch - Medium Light Output -1/4 Watt LENGTH LPS10QDV2ColorFinishTemp 10-2W LPS12QDV4ColorFinishTemp 12-4W LPS18QDV6ColorFinishTemp 18-6W LPS24QDV8ColorFinishTemp 24-8W LPS30QDV10ColorFinishTemp 30-10W LPS36QDV12ColorFinishTemp 36-12W 24-1/2 fixture shown Medium Light Output - 1/4 watt #OF RECEPT. RECEPT. COLOR FINISH 1 B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, /8" 3/8" Fixture Section LPS36DV12ColorFinishTemp LPS24DV8ColorFinishTemp 24- LPS30DV10ColorFinishTemp 12-6" 6" 6" 6" 11" " 10-3" 3" 3" 5" Legend = Receptacle (Available in White, Gray, and Black) = Switch (Available in Black or White- 4- from left side) = Divider Plate (Low Voltage) = Driver Medium Light Output - 1/4 Watt LEDS INTEGRAL DRIVER Tamper Resistant APS with integrated LED Lighting Rocker Switch 3-Year Limited Warranty Dimmable with separate lighting circuit No UV or IR WITH BUILT-IN DRIVER Construction Materials: Powder Coated Extruded Aluminum (heatsink), IR Acrylic (lens) Under Cabinets Under Fixed Shelving Office Cubicles Shops & Garages MAELV-600-Color MA-R-Color 300W Diva slide dimmer 300W Diva slide dimmer 3-way Maestro electronic smart dimmer Maestro companion dimmer LPS18DV6ColorFinishTemp 10-3" 5" 18- LPS12DV4ColorFinishTemp 12-10" 1" = Knock-out ( from right side - from left side) located on back frame DRIVER Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: 1/4 Watt LEDs LED Board: 6" or 12" 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) Receptacle Colors LPS10DV2ColorFinishTemp 9-1" NOTE: 6"LED board is mounted 10- in center of 10- fixture Back Frame Cover 3- Divider Plate 120V Wood Screws & Wall Anchors 12 ga.romex Dry Only Finish Options Black (B) Gray (G) White (W) 4- Black () Bronze (BZ) Satin Nickel (SN) White () 12 S-LPS-DVSERIES-SPEC-0618 S-LPS-DVSERIES-SPEC

8 Lighted Power Strip DV Series Installation Instructions for LPS WITH Built-In Driver Lighted Power Strip DV Series Wiring Diagram for 18- LPS WITH Built-In Driver General Guidelines Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS. All wiring must meet NEC and local codes. Light valance recommended. Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed. Bottom of Cabinet Wiring Diagram for Combined Light & Receptacle Circuit - Non Dimmable Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into knockout hole inside of back frame. Pull wires into LPS. Positive (+) Negative (-) Tool Wiring for Combined Light and Receptacle Circuit - Non Dimmable Factory Wired Back Frame DRIVER Divider Plate RED + BLUE - SWITCH Cover DRIVER DIVIDER PLATE 120V 12-1/2 Fixture Shown 120V Receptacle Circuit. Must be GFCI Protected. Step 1 Secure LPS to wall by screwing into wall studs or use anchors provided. Connect BLACK Romex wire to BLACK wire from receptacles and switch. Connect WHITE Romex wire to WHITE wire from receptacles and driver. Ground all GREEN wires to PEM studs inside of back frame. Step 2 Step 3 Step 4 When connecting 2 or more LPS fixtures, run Romex from fixture to fixture. Ground each section to the next. To terminate last LPS, use wire nuts on ends of wires. Snap cover in place and turn power on. Wiring Diagram for Separate Light & Receptacle Circuits 18-1/2 Fixture Shown Wiring for Separate Light and Receptacle Circuits Factory Wired Positive (+) Negative (-) RED + BLUE - DRIVER SWITCH Back Frame DRIVER Divider Plate DIVIDER PLATE 120V 120V for lights 120V for receptacles 12-1/2 Fixture Shown Cover Lighting Circuit Step 1 Secure LPS to wall by screwing into wall studs or use anchors provided. If running two circuits, one for receptacles, one for lighting, connect fixture wires to appropriate Romex wires. BLACK to BLACK. WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame. Step 2 Step 3 When connecting 2 or more LPS fixtures, run Romex from fixture to fixture. Ground each section to the next. To terminate last LPS, use wire nuts on ends of wires. 120V Receptacle Circuit. Must be GFCI Protected. (non dimmable) Step 4 Snap cover in place and turn power on. 18-1/2 Fixture Shown 14 S-LPS-DVSERIES-INSTALL-0618 S-LPS-DVSERIES-INSTALL

9 Lighted Power Strip RM Series for LPS WITHOUT Built-In Driver 2-5/8" Lighted Power Strip RM Series for LPS WITHOUT Built-In Driver Installed view High Light Output - 1/2 watt Construction Materials: Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: Powder Coated Extruded Aluminum (heatsink), IR Acrylic (lens) 1/2 Watt LEDs LED Board: 6" or 12" Max Run: 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) 120V (receptacles) & 15 Volt DC (lighting) Wood Screws & Wall Anchors 18/2 solid (recommended)- for Lighting 12 ga. Romex- for Receptacle Dry Only Refer to Driver Specs Optional Installation Components APS-Switch APT-R-15A LENGTH Rocker Switch (available in Black or White) 15Amp Tamper Resistant Receptacle. Available in Black, Gray, and White LPS10HRM3ColorFinishTemp 10-3W LPS12HRM6ColorFinishTemp 12-6W LPS18HRM9ColorFinishTemp 18-9W LPS24HRM12ColorFinishTemp 24-12W LPS30HRM15ColorFinishTemp 30-15W LPS36HRM18ColorFinishTemp 36-18W LPS42HRM21ColorFinishTemp 42-21W LPS48HRM24ColorFinishTemp 48-24W LPS60HRM30ColorFinishTemp 60-30W LPS72HRM36ColorFinishTemp 72-36W High Light Output - 1/2 Watt LEDs REMOTE DRIVER Tamper Resistant APS with integrated LED Lighting 3-Year Limited Warranty Dimmable (with compatible dimmer) No UV or IR WITHOUT DRIVER 24-1/2 fixture shown Task Lighting retains the right to modify the design of our products without prior notice #OF RECEPT. RECEPT. COLOR FINISH Power Supplies / OUTPUT INPUT 1 B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, B, G, W, BZ,, 3240 Under Cabinets Office Cubicles Under Fixed Shelving Shops & Garages MAELV-600-Color MA-R-Color **WS-LED-CVD-902 *WS-SR-Color-902 TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A Receptacle Colors Finish Options Black () 1" Fixture Section Black (B) Gray (G) White (W) Bronze (BZ) 1-5/8" 300W Diva slide dimmer 300W Diva slide dimmer 3-way Maestro electronic smart dimmer Maestro companion dimmer Satin Nickel (SN) 1-5/8" Sempria dimming module for wireless system Sempria wireless dimmer/ switch. Available in Black, Gray, Ivory, Light Almond, and White **NOTE: Call TASK for alternate driver White () LPS72RM36ColorFinishTemp 12" " LPS60RM30ColorFinishTemp 1 LPS48RM24ColorFinishTemp LPS42RM21ColorFinishTemp 10-3/4" 6-1/4" 6-1/4" 6-1/4" 6-1/4" 6-3/4" LPS36RM18ColorFinishTemp LPS30RM15ColorFinishTemp LPS24RM12ColorFinishTemp LPS18RM9ColorFinishTemp 10-3" 5" LPS12RM6ColorFinishTemp LPS10RM3ColorFinishTemp 9-1" NOTE: 6"LED board is mounted 10- in center of 10- fixture Custom Options/Details 16 S-LPS-RMSERIES-SPEC-0618 S-LPS-RMSERIES-SPEC " 10-3" 3" 3" 5" 10" 12-6" 6" 6" 6" 11" " 1" Back Frame Cover 1½" Legend = Receptacle (Available in, GR, or ) = Divider Plate (Low Voltage) = Knock-out ( from right side - from left side). located on back frame = Low Voltage Entry ( from left side) located on back frame Custom lengths from (larger sizes will have a seam when assembled) 120 Volt integral switch (available in black or white only) Custom receptacle/switch placement Receptacles must be a minimum of 1-1/2 apart (on center) Receptacles must be a minimum of 1 from right side & 5-1/2 from left side. Knockout cannot be behind device. Custom charges will apply - Call for a quote, lead time, and assistance with your custom order Divider Plate

10 Lighted Power Strip RM Series Installation Instructions for LPS WITHOUT Built-In Driver SG9 Series Linear under cabinet LED Lighting with integrated WireWay system for concealed wire management General Guidelines Power source MUST be a 20 amp branch circuit protected by a GFCI at the panel or GFCI prior to the connection at LPS. All wiring must meet NEC and local codes. Light valance recommended. Firmly insert plug straight into receptacle, applying equal pressure to both blades at the same time. Gently rock plug, if needed. Turn power off at panel. Carefully pry open each piece with tool (provided). Insert Romex connector into knockout hole inside of back frame. Pull wires into LPS. Step 1 Step 2 Step 3 18 Bottom of Cabinet Back Frame Cover Positive (+) Tool 15vDC wire Negative (-) Remote Driver- 120V Entry RED + Divider Plate Secure LPS to wall by screwing into wall studs or use anchors provided. Connect BLACK to BLACK, WHITE to WHITE. Ground all GREEN wires to PEM studs inside of back frame. When connecting two LPS, run Romex from fixture to fixture. Ground each section to the next. To terminate last LPS, use wire nuts on ends of wires. BLACK - LOW VOLTAGE DIVIDER PLATE Step 4 Step 5 120V Using appropriate knockout hole, pull low voltage wire from remote power supply into the low voltage space, connect BLACK wire (negative) to BLACK wire from lights and RED wire (positive) to RED wire. Snap cover in place and turn power on. 12-1/2 Fixture Shown 120V Circuit 18-1/2 Fixture Shown Remote Driver-Low Voltage Entry S-LPS-RMSERIES-INSTALL-0618 WireWay Section 1-1/4" 1 ¼ " 50,000 hour LED life at 70% lumen maintenance Concealed wire management with hidden poke-home connectors Frosted, light-diffusing lens Streamlined from WireWay to light 3-year limited warranty No UV or IR Dimmable (with compatible dimmer) Under Cabinet Lighting Cove Lighting Display Lighting Construction Materials: Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: RPVC (mount), extruded aluminum (heatsink), IR Acrylic (lens) 1/2 Watt LEDs LED Board: 6" or 12" Fixture Section 1-1/4" 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) 15 Volt DC Screws (included) High Light Output - 1/2 watt Black (B) DIMENSIONS Wire management system Conceals wire from wall to fixture Available in Black, Gray, and White Gray (G) SG9-6UC3-MountColor-Temp 6" x 1-1/4" x 3W SG9-12UC6-MountColor-Temp 12" x 1-1/4" x 6W SG9-18UC9-MountColor-Temp 17-7/8" x 1-1/4" x 9W SG9-24UC12-MountColor-Temp 23-7/8" x 1-1/4" x 12W SG9-30UC15-MountColor-Temp 29-3/4" x 1-1/4" x 15W SG9-36UC18-MountColor-Temp 35-3/4" x 1-1/4" x 18W SG9-42UC21-MountColor-Temp 41-3/4" x 1-1/4" x 21W SG9-48UC24-MountColor-Temp 47-3/4" x 1-1/4" x 24W WireWay Colors Mounting Bracket Colors White (W) Power Supplies / OUTPUT INPUT TLD-24WSI* 24W plug in 15V DC Plug In TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A *Call for dimming options Installation Components SP-20FT-18/2 SP-50FT-18/2 SG9-WW-48-Color SG9-WW-MJ12-Color SG9-IL-CONN 20 foot spool of 18/2 awg solid wire 50 foot spool of 18/2 awg solid wire 48" Field Cuttable WireWay Miter joint - 45º cuts (2) 12-inch pieces In-line Connector 300W Diva slide dimmer 300W Diva slide dimmer 3-way Max Run: Refer to driver specs MAELV-600-Color Maestro electronic smart dimmer MA-R-Color Maestro companion dimmer 18/2 solid (recommended) *WS-LED-CVD-902 Sempria dimming module for wireless system Dry and damp locations Sempria wireless dimmer/ switch. Available in Black, Gray, Ivory, Task Lighting retains the right to modify the design of our products *WS-SR-Color-902 Light Almond, and White without prior notice **NOTE: Call TASK for alternate driver SG9-SPEC

11 SG9 Series Installation Instructions SG9 Series Installation Instructions WireWay light Fixture Section 1-1/4" WireWay Section 1-1/4 1 ¼ " 1. Cut SG9-WW WireWay Base the length from wire entry location (at back of cabinet) to the front of cabinet. Miter the corner or use SG9-WW- MJ12 (12 miter piece) to turn the corner. Deburr all cut edges to ensure wire safety. 4. Cut wire to fit between adjacent fixtures. Insert wires into terminal blocks, maintaining polarity (RED wire to RED terminal, BLACK wire to BLACK terminal.) Maintain polarity or fixtures will not work. GENERAL GUIDELINES A 15 VOLT DC DRIVER MUST BE USED WITH SEMPRIA FIXTURES! Driver must be 15 Volt DC supplied by Task Lighting only!* All wiring must meet NEC or local codes. 18/2 solid wire is recommended from driver to fixtures and between fixtures. (If 18/2 solid wire is not available, 18/2 stranded wire may also be used. Tin ends of wire if possible.) A maximum of 75 Watts of Sempria LED Lighting is allowed on a zone. Limit wire length to 30 feet from driver to lights. Place switches on the 120 Volt side of the Driver (15 Volt DC). De-burr all cut WireWay edges to ensure wire safety. If other than Task specified dimmers are desired, call Task Lighting for instructions. Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info. DRIVER (15 Volt DC) LOCATIONS Some Drivers may be conveniently concealed within our TR Series Angle Power Strip or Lighted Power Strip. A sink base or the top of a cabinet are other common driver locations. Driver must be accessible. DO NOT LOCATE DRIVER IN ATTIC. PRE-WIRING Run separate wire from Driver (15 Volt DC) location to each zone. When total wattage of Sempria LED fixtures in zone exceeds 75 Watts, use a second driver and run additional 18/2 solid wire for another zone. Length of wire from driver to first fixture in each zone is not to exceed 30 feet. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.) 2. Cut WireWay Base to fit full length of cabinet face. Deburr cut edges. Using screws provided, secure Base to bottom of cabinet every 12. (When wiring between adjacent cabinets, drill 1/4 hole through end panels.) 3. Strip 1/4 insulation from driver wires. Push RED solid wire straight into terminal block with RED mark. Push BLACK solid wire straight into terminal block with BLACK mark. (18/2 solid wire is recommended. If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire.) 5. Snap lens onto fixture. Position fixture in center of cabinet and snap into WireWay Base. 6. Cut WireWay Cover (or miter piece) to fit exposed Base. Deburr cut WireWay edges. Snap into Base. OPTION: Installing Sempria Fixtures Without WireWay Use mounting channel supplies with fixture. Use screws provided to secure mounting channel to underside at face of cabinet. Follow step 3 instructions. Position fixture in channel and snap into place. 20 SG9-INSTALL-0618 SG9-INSTALL

12 A Series Linear LED fixture with Angled Housing and a slim profile for multiple applications F Series Linear LED fixture with Flat Housing and a slim profile for multiple applications Toe/Soffit Lighting Cove Lighting Interior Cabinet Lighting Display Case Lighting 50,000 hour LED life at 70% lumen maintenance Compact and versatile Frosted lens Poke-home connectors for easy installation 3 Year limited warranty No special gap-connectors needed No UV or IR Dimmable (with compatible dimmer) Construction Materials: Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: LED Board: 6" or 12" Max Run: Extruded aluminum (heatsink), IR Acrylic (lens) 1/8 and 1/4 Watt LEDs 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) 15 Volt DC Double Stick Tape / Screws included Refer to driver specs 18/2 solid (recommended) Dry and damp locations section 5/8" Task Lighting retains the right to modify the design of our products without prior notice Angled Housing PART NUMBER DIMENSIONS FLAT Medium HOUSING Light ⅛ Output WATT - 1/4 watt SA9Q-6UN2-Temp 6- x x 5/8" 2W SA9Q-12UN4-Temp 12- x x 5/8" 4W SA9Q-18UN6-Temp 18- x x 5/8" 6W SA9Q-24UN8-Temp 24- x x 5/8" 8W SA9Q-30UN10-Temp 30- x x 5/8" 10W SA9Q-36UN12-Temp 36- x x 5/8" 12W SA9Q-42UN14-Temp 42- x x 5/8" 14W SA9Q-48UN16-Temp 48- x x 5/8" 16W Low Light Output - 1/8 watt SA9E-6UN1-Temp 6- x x 5/8" 1W SA9E-12UN2-Temp 12- x x 5/8" 2W SA9E-18UN3-Temp 18- x x 5/8" 3W SA9E-24UN4-Temp 24- x x 5/8" 4W SA9E-30UN5-Temp 30- x x 5/8" 5W SA9E-36UN6-Temp 36- x x 5/8" 6W SA9E-42UN7-Temp 42- x x 5/8" 7W SA9E-48UN8-Temp 48- x x 5/8" 8W Installation Components SP-20FT-18/2 SP-50FT-18/2 SF9-WW-48 SG9-IL-CONN Power Supplies / OUTPUT INPUT TLD-24WSI* 24W plug in 15V DC Plug In 20 foot spool of 18/2 awg solid wire 50 foot spool of 18/2 awg solid wire 48" Sempria LED Universal WireWay for FLAT HOUSING In-line Connector TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A *Call for dimming options MAELV-600-Color MA-R-Color *WS-LED-CVD-902 *WS-SR-Color W Diva slide dimmer 300W Diva slide dimmer 3-way Maestro electronic smart dimmer Maestro companion dimmer Sempria dimming module for wireless system Sempria wireless dimmer/ switch. Available in Black, Gray, Ivory, Light Almond, and White **NOTE: Call TASK for alternate driver Toe/Soffit Lighting Cove Lighting Interior Cabinet Lighting Under Cabinet Lighting Display Case Lighting Power Supplies / OUTPUT INPUT TLD-24WSI* 24W plug in 15V DC Plug In TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A 22 S-A-SERIES-SPEC-0618 S-F-SERIES-SPEC ,000 hour LED life at 70% lumen maintenance Compact and versatile Frosted lens Poke-home connectors for easy installation 3 Year limited warranty No special gap-connectors needed No UV or IR Dimmable (with compatible dimmer) Construction Materials: Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: LED Board: 6" or 12" Max Run: Extruded aluminum (heatsink), IR Acrylic (lens) 1/8 and 1/4 Watt LEDs 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) 15 Volt DC Double Stick Tape / Screws included Refer to driver specs 18/2 solid (recommended) Dry and damp locations 3/8" section Task Lighting retains the right to modify the design of our products without prior notice Flat Housing PART NUMBER DIMENSIONS Medium Light Output - 1/4 watt SF9Q-6UN2-Temp 6- x x 2W SF9Q-12UN4-Temp 12- x x 4W SF9Q-18UN6-Temp 18- x x 6W SF9Q-24UN8-Temp 24- x x 8W SF9Q-30UN10-Temp 30- x x 10W SF9Q-36UN12-Temp 36- x x 12W SF9Q-42UN14-Temp 42- x x 14W SF9Q-48UN16-Temp 48- x x 16W Low Light Output - 1/8 watt SF9E-6UN1-Temp 6- x x 1W SF9E-12UN2-Temp 12- x x 2W SF9E-18UN3-Temp 18- x x 3W SF9E-24UN4-Temp 24- x x 4W SF9E-30UN5-Temp 30- x x 5W SF9E-36UN6-Temp 36- x x 6W SF9E-42UN7-Temp 42- x x 7W SF9E-48UN8-Temp 48- x x 8W *Call for dimming options Installation Components SP-20FT-18/2 SP-50FT-18/2 SF9-WW-48 SG9-IL-CONN MAELV-600-Color MA-R-Color *WS-LED-CVD-902 *WS-SR-Color foot spool of 18/2 awg solid wire 50 foot spool of 18/2 awg solid wire 48" Sempria LED Universal WireWay for FLAT HOUSING In-line Connector 300W Diva slide dimmer 300W Diva slide dimmer 3-way Maestro electronic smart dimmer Maestro companion dimmer Sempria dimming module for wireless system Sempria wireless dimmer/ switch. Available in Black, Gray, Ivory, Light Almond, and White **NOTE: Call TASK for alternate driver

13 A & F Series Installation Instructions A & F Series Installation Instructions 3/8" section 5/8" section INSTALLING FIXTURES GENERAL GUIDELINES A 15 VOLT DC DRIVER MUST BE USED! Driver must be 15 volt DC supplied by Task Lighting only!* All wiring must meet NEC or local codes. 18/2 solid wire is recommended from driver to fixtures and between fixtures. (If 18/2 solid wire is not available, 18/2 stranded wire may also be used. Tin ends of wire if possible.) A maximum of 75 Watts of Sempria LED Lighting is allowed on a zone. Limit wire length to 30 feet from driver to lights. Place switches on the 120 Volt side of the Driver. De-burr all WireWay edges to ensure wire safety. If other than Task specified dimmers are desired, call Task Lighting for instructions. Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info. 1. Slide lens back to expose connectors or remove lens from fixture. 2. Strip 1/4" from RED wire and insert into terminal block opening with RED marking. Strip BLACK wire, insert into terminal block opening with BLACK mark. (If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire.) 3. Cut wires to fit between adjacent fixtures. Insert wires into terminal blocks, maintaining polarity (RED wire to RED terminal, BLACK wire to BLACK terminal.) MAINTAIN POLARITY OR THE FIXTURE WILL NOT WORK. 4. If fixture does not light, reverse wires. 5. Mounting surface must be finished and dust-free for mounting tape to properly adhere. Remove backing from mounting tape and press fixture firmly into place. 6. Using screws provided, secure fixture in place. DO NOT pierce LED strip with screws, nails, staples, or any other mechanical device. 7. Slide or snap lens back into place. DRIVER (15 volt DC) LOCATIONS Some Drivers may be conveniently concealed within our TR Series Angle Power Strip or Lighted Power Strip. A sink base or the top of a cabinet are other common driver locations. Driver must be accessible. DO NOT LOCATE DRIVER IN ATTIC. PRE-WIRING Run separate wire from Driver (15 Volt DC) location to each zone. When total wattage of Sempria LED fixtures in zone exceeds 75 Watts, use a second driver and run additional 18/2 solid wire for additional zone. Length of wire from driver to first fixture in each zone is not to exceed 30 feet. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.) NOTE: If using stranded wire we recommend tinning the end of the wire first. If stranded wire is used without tinning, terminal block tabs must be depressed when inserting wires. Note that wiring with untinned stranded wire may result in a poor connection. Start both sets of wires from drivers at a common point and wire the zones in opposite directions. WHEN USING TWO DRIVERS: 15vDC Driver #1 D $ D Driver #2 120V Switch 24 S-A&F-SERIES-INSTALL-0618 S-A&F-SERIES-INSTALL

14 Under Cabinet Interior Cabinet Floating Shelves Fixed Shelves Closet Design for recessed flush mounting 50,000 hour LED life at 70% lumen maintenance Compact and versatile Frosted lens Poke-Home connectors for easy installation 3 Year limited warranty No special gap-connectors needed No UV or IR Dimmable (with compatible dimmer) Construction Materials: Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: LED Board: 6" or 12" Max Run: Power Supplies R Series Linear LED Recessed fixture Anodized extruded aluminum (heatsink), IR Acrylic (lens) 1/8 Watt, 1/4 Watt, 1/2 Watt LEDs 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) 15 Volt DC Double Stick Tape / Screws (included) Refer to driver specs 18/2 solid (recommended) Dry and damp locations / OUTPUT 5/8" 7/8" Section INPUT TLD-24WSI* 24W plug in 15V DC Plug In TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A *Call for dimming options 7/16" Task Lighting retains the right to modify the design of our products without prior notice High Light Output - 1/2 watt Medium Light Output - 1/4-1/4 watt watt Low Light Output - 1/8-1/8 watt watt DIMENSIONS DIMENSIONS DIMENSIONS SR9E-8UN1-Temp 7-5/8" x 5/8" x 1W SR9E-14UN2-Temp 13-5/8" x 5/8" x 2W SR9E-20UN3-Temp 19-5/8" x 5/8" x 3W SR9E-26UN4-Temp 25-5/8" x 5/8" x 4W SR9E-32UN5-Temp 31-5/8" x 5/8" x 5W SR9E-38UN6-Temp 37-5/8" x 5/8" x 6W SR9E-44UN7-Temp 43-5/8" x 5/8" x 7W SR9E-50UN8-Temp 49-5/8" x 5/8" x 8W SR9Q-8UN2-Temp 7-5/8" x 5/8" x 2W SR9Q-14UN4-Temp 13-5/8" x 5/8" x 4W SR9Q-20UN6-Temp 19-5/8" x 5/8" x 6W SR9Q-26UN8-Temp 25-5/8" x 5/8" x 8W SR9H-8UN3-Temp 7-5/8" x 5/8" x 3W SR9H-14UN6-Temp 13-5/8" x 5/8" x 6W SR9H-20UN9-Temp 19-5/8" x 5/8" x 9W SR9H-26UN12-Temp 25-5/8" x 5/8" x 12W SR9H-32UN15-Temp 31-5/8" x 5/8" x 15W SR9H-38UN18-Temp 37-5/8" x 5/8" x 18W SR9H-44UN21-Temp 43-5/8" x 5/8" x 21W SR9H-50UN24-Temp 49-5/8" x 5/8" x 24W SR9Q-32UN10-Temp 31-5/8" x 5/8" x 10W SR9Q-38UN12-Temp 37-5/8" x 5/8" x 12W SR9Q-44UN14-Temp 43-5/8" x 5/8" x 14W SR9Q-50UN16-Temp 49-5/8" x 5/8" x 16W Installation Components SP-20FT-18/2 SP-50FT-18/2 SR9-EC-KIT MAELV-600-Color MA-R-Color *WS-LED-CVD-902 *WS-SR-Color W Diva slide dimmer 300W Diva slide dimmer 3-way 20 foot spool of 18/2 awg solid wire 50 foot spool of 18/2 awg solid wire Maestro electronic smart dimmer Maestro companion dimmer End Cap Kit -Wire entry openings-light Gray Only Sempria dimming module for wireless system Sempria wireless dimmer/ switch. Available in Black, Gray, Ivory, Light Almond, and White **NOTE: Call TASK for alternate driver R Series Installation in Solid Bottom GENERAL GUIDELINES All wiring must meet NEC or local codes. 18/2 solid wire is strongly recommended, from driver to fixtures, and between fixtures. Wire length is maximum of 30 feet from driver to fixtures. Maximum of 75 Watts of Sempria LED lighting is allowed per zone. Place switches on the 120V side of driver. If other than Task specified dimmers are desired, call Task Lighting for instructions. Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info. DRIVERS 15 VOLT DC DRIVER, supplied by Task Lighting only, must be used. Driver must be accessible; the sink base or top of cabinet are common locations. Do not locate driver in attic. Some drivers may be concealed within our TR Series Angle Power Strip or Lighted Power Strip. PRE-WIRING Run separate wire from Driver location to each zone. If total wattage of Sempria LED fixtures in zone exceeds 75 Watts, use a second driver and run additional 18/2 solid wire for additional zone. When using two drivers, start both sets of wires from a common point and wire the zones in opposite directions. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.) Bottom Shelf of Cabinet INSTALLATION 1. Using a 5/8 router bit, hollow out a groove (the length of the fixture) from cabinet or shelf bottom. 2. Remove lens from fixture. 3. Strip 1/4 insulation from 18/2 wires that run from driver. Insert wires into terminal block at either end of fixture (RED wire to terminal with RED mark, BLACK wire to terminal with BLACK mark.) 4. Apply double stick tape (provided) to back of fixture and insert into groove. Fixture will fit tight. Secure fixture with screws (provided). 5. Snap lens back in place. If using end caps, please refer to the end cap instructions. 26 S-R-SERIES-SPEC-0618 S-R-SERIES-INSTALL Counter Top Backsplash Bottom Shelf of Cabinet Counter Top Backsplash

15 R Series Installation in Flush Panel Bottom GENERAL GUIDELINES All wiring must meet NEC or local codes. 18/2 solid wire is strongly recommended, from driver to fixtures, and between fixtures. Wire length is maximum of 30 feet from driver to fixtures. Maximum of 75 Watts of Sempria LED lighting is allowed per zone. Place switches on the 120V side of driver. If other than Task specified dimmers are desired, call Task Lighting for instructions. Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info. DRIVERS 15 VOLT DC DRIVER, supplied by Task Lighting only, must be used. Driver must be accessible; the sink base or top of cabinet are common locations. Do not locate driver in attic. Some drivers may be concealed within our TR Series Angle Power Strip or Lighted Power Strip. PRE-WIRING Run separate wire from Driver location to each zone. If total wattage of Sempria LED fixtures in zone exceeds 75 Watts, use a second driver and run additional 18/2 solid wire for additional zone. When using two drivers, start both sets of wires from a common point and wire the zones in opposite directions. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.) Bottom Shelf of Cabinet ¼" Finished Panel Counter Top INSTALLATION 1. Using a 5/8 router bit, hollow out a groove (the length of fixture) from flush panel. 2. Remove lens from fixture. 3. Strip 1/4" insulation from 18/2 solid wires that run from driver. Insert wires into terminal block at either end of fixture (RED wire to terminal with RED mark, BLACK wire to terminal with BLACK mark.) 4. Snap lens back onto fixture. 5. Insert fixture into routed groove (fixture will fit tightly.) 6. If needed use a silicone adhesive, spot-secure fixture to panel from top-side. 7. Attach flush panel to bottom of cabinet. Toe/Soffit Lighting Cove Lighting Interior Cabinet Lighting Display Case Lighting Stair Lighting S Series Linear LED fixture with slim profile TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A MA-R-Color Maestro companion dimmer If using end caps, please refer to the end cap instructions. *Call for dimming options *WS-LED-CVD-902 Sempria dimming module for wireless system Sempria wireless dimmer/ switch. Available in Black, Task Lighting retains the right to modify the design of our products without prior notice *WS-SR-Color-902 Gray, Ivory, Light Almond, and White 28 S-R-SERIES-INSTALL-0618 S-S-SERIES-SPEC-0618 **NOTE: Call TASK for alternate driver 29 Built in light valance with light shield 50,000 hour LED life at 70% lumen maintenance Compact and versatile Frosted lens Poke-Home connectors for easy installation 3 Year limited warranty No special gap-connectors needed No UV or IR Dimmable (with compatible dimmer) Construction Materials: Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: LED Board: 6" or 12" Max Run: Power Supplies Anodized extruded aluminum (heatsink), IR Acrylic (lens) 1/8 Watt, 1/4 Watt, 1/2 Watt LEDs 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) 15 Volt DC Double Stick Tape / Screws (included) Refer to driver specs 11/16" 18/2 solid (recommended) Dry and damp locations 3/4" / OUTPUT INPUT TLD-24WSI* 24W plug in 15V DC Plug In Section TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A 7/8" Hight Light Output - 1/2 watt PART NUMBER PART NUMBER DIMENSIONS DIMENSIONS DIMENSIONS SS9E-6UN1-Temp 6- x 3/4" x 11/16" 1W SS9E-12UN2-Temp 12- x 3/4" x 11/16" 2W SS9E-18UN3-Temp 18- x 3/4" x 11/16" 3W SS9E-24UN4-Temp 24- x 3/4" x 11/16" 4W SS9E-30UN5-Temp 30- x 3/4" x 11/16" 5W SS9E-36UN6-Temp 36- x 3/4" x 11/16" 6W SS9E-42UN7-Temp 42- x 3/4" x 11/16" 7W SS9E-48UN8-Temp 48- x 3/4" x 11/16" 8W SS9H-6UN3-Temp 6- x 3/4" x 11/16" 3W SS9H-12UN6-Temp 12- x 3/4" x 11/16" 6W SS9H-18UN9-Temp 18- x 3/4" x 11/16" 9W SS9H-24UN12-Temp 24- x 3/4" x 11/16" 12W SS9H-30UN15-Temp 30- x 3/4" x 11/16" 15W SS9H-36UN18-Temp 36- x 3/4" x 11/16" 18W SS9H-42UN21-Temp 42- x 3/4" x 11/16" 21W SS9H-48UN24-Temp 48- x 3/4" x 11/16" 24W Medium Light Output - 1/4 watt SS9Q-6UN2-Temp 6- x 3/4" x 11/16" 2W SS9Q-12UN4-Temp 12- x 3/4" x 11/16" 4W SS9Q-18UN6-Temp 18- x 3/4" x 11/16" 6W SS9Q-24UN8-Temp 24- x 3/4" x 11/16" 8W SS9Q-30UN10-Temp 30- x 3/4" x 11/16" 10W SS9Q-36UN12-Temp 36- x 3/4" x 11/16" 12W SS9Q-42UN14-Temp 42- x 3/4" x 11/16" 14W SS9Q-48UN16-Temp 48- x 3/4" x 11/16" 16W Low Light Output - 1/8 watt Installation Components SP-20FT-18/2 SP-50FT-18/2 SG9-IL-CONN SS9-WW-48 MAELV-600-Color 20 foot spool of 18/2 awg solid wire 50 foot spool of 18/2 awg solid wire In-line Connector 48 Sempria LED WireWay for S Series 300W Diva slide dimmer 300W Diva slide dimmer 3-way Maestro electronic smart dimmer

16 S Series Installation Instructions S Series Mounting Positions Not to Scale GENERAL GUIDELINES All wiring must meet NEC or local codes. 18/2 solid wire is strongly recommended, from driver to fixtures, and between fixtures. Wire length is maximum of 30 feet from driver to fixtures. Maximum of 75 Watts of Sempria LED lighting is allowed per zone. Place switches on the 120V side of driver. If other than Task specified dimmers are desired, call Task Lighting for instructions. Improper installation or applying improper voltage to fixture will void warranty. See TaskLighting.com for full warranty info. Interior Cabinet-Vertical shelf Window Sill window Toe Kick DRIVERS 15 VOLT DC DRIVER, supplied by Task Lighting only, must be used. Driver must be accessible; the sink base or top of cabinet are common locations. Do not locate driver in attic. Some drivers may be concealed within our TR Series Angle Power Strip or Lighted Power Strip. top view backsplash PRE-WIRING Run separate wire from Driver location to each zone. If total wattage of Sempria LED fixtures in zone exceeds 75 Watts, use a second driver and run additional 18/2 solid wire for additional zone. When using two drivers, start both sets of wires from a common point and wire the zones in opposite directions. Wiring may start at either end of fixture. (Option: separate wire may be run from driver to each fixture.) Stairs Cove Soffit-Above Cabinet WHEN USING TWO DRIVERS: 15vDC Start both sets of wires from drivers at a common point and wire the zones in opposite directions. Driver #1 D $ D Driver #2 120V Switch INSTALLATION 1. Remove lens from fixture. 2. Select side of fixture that will attach to mounting surface. Using 1/8 bit, drill two mounting holes one near each end of fixture (location is indicated by BLACK mark on end of fixture.) DO NOT pierce or damage LED board. Deburr metal. 3. Apply foam double-stick tape squares to same side of fixture, avoiding the mounting holes. 4. Strip ¼ from RED 18/2 solid wire; push wire straight into terminal block opening with RED mark. Strip BLACK 18/2 solid wire; push wire straight into terminal block opening with BLACK mark. (If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire.) 5. Cut wires to fit between adjacent fixtures. Insert wires into terminal blocks, maintaining polarity (RED wire to RED terminal, BLACK wire to BLACK terminal.) 6. If fixture does not light, reverse wires. Gently depress terminal block tab and carefully pull wires straight out. 7. Mounting surface must be finished and dust/residue free. Peel backing from tape squares and press firmly into place. 8. Using screws provided, secure fixture in place. DO NOT pierce LED strip with screws, nails, staples or any other mechanical device. 9. Snap lens back into place. Deck Rail 30 S-S-SERIES-INSTALL-0618 S-S-SERIES-INSTALL

17 Lighted Closet Rod Illuminated LED Lighted Closet Rod Lighted Closet Rod Installation Instructions Fixture Section Flange Section 1-1/4" 3-3/8" 2-1. Rod and lens must be 3/8 shorter than closet width measurement. 8. Insert non-wired side of rod into installed flange. 50,000 hour LED life at 70% lumen maintenance Each end field trimmable up to 3" 15V DC plug-in or hardwire drivers (ordered separately) Accessories sold separately: Center Bracket Support No UV or IR Closet Lighting Laundry Room Lighting Dimensions: Construction Materials: Wattage: CRI: 90+ LED Beam Angle: 120º LED Spacing: 1-1/2 Accessories LC9R-CBS-P-Finish Finish Options 18" - 96" L x W x 1-1/4" H Extruded aluminum-powder Coat Finish 1/4 Watt LEDs LED Board: 6" or 12" 15 Volt DC Max Run: Flange Set LC9R-FS-P- LC9R-FS-P-BZ LC9R-FS-P-SN LC9R-FS-P- 2700K (Warm White), 3000K (Soft White) 4000K (Cool White), 5000K (Daylight White) Flange set and center brackets Refer to driver specs 18/2 solid (recommended) Dry and wet locations Center Bracket Support (Use every 4' for fixtures over 48") LED Closet Rod Flange Set-Black LED Closet Rod Flange Set-Bronze LED Closet Rod Flange Set-Satin Nickel LED Closet Rod Flange Set-White Black () Bronze (BZ) Satin Nickel (SN) White () Task Lighting retains the right to modify the design of our products without prior notice 3" Medium S Light Output - 1/4 watt LENGTH LC9R18-4-P-Finish-Temp 18" 4, 621 LC9R24-6-P-Finish-Temp 24" 6, 828 LC9R30-8-P-Finish-Temp 30" 8, 1035 LC9R36-10-P-Finish-Temp 36" 10, 1242 LC9R42-12-P-Finish-Temp 42" 12, 1449 LC9R48-14-P-Finish-Temp 48" 14, 1656 LC9R54-16-P-Finish-Temp 54" 16, 1863 LC9R60-18-P-Finish-Temp 60" 18, 2070 LC9R66-20-P-Finish-Temp 66" 20, 2277 LC9R72-22-P-Finish-Temp 72" 22, 2484 LC9R78-24-P-Finish-Temp 78" 24, 2691 LC9R84-26-P-Finish-Temp 84" 26, 2898 LC9R90-28-P-Finish-Temp 90" 28, 3105 LC9R96-30-P-Finish-Temp 96" 30, 3312 Installation Components SP-20FT-18/2 Flange set included with each closet rod 20 foot spool of 18/2 awg solid wire SP-50FT-18/2 50 foot spool of 18/2 awg solid wire MCS-10-Color 10W Max - Magnetic Contact Switch. Available in Brown, Gray, or White MCS-100-Color 100W Max - Magnetic Contact Switch. Available in Brown, Gray, or White MS-OPS5M-Color 5 Amp - Maestro Occupancy Sensor Switch MS-VPS5M-Color 11-7/8" 1-1/8" 10-7/8" 5 Amp - Maestro Vacancy Sensor Switch 1" Wide Center Bracket Support Section 15/16" Power Supplies / OUTPUT INPUT TLD-24WSI* 24W plug in 15V DC Plug In TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A *Call for dimming options 2. If field-trimming is necessary, slide lens out of fixture. Use scissors or shears to trim lens to length (3/8 shorter than closet width.) 3. Use chop or hacksaw to cut rod to proper length. DO NOT CUT LED CIRCUIT BOARD. Deburr all cut edges. Slide lens back into place. 4. Prep wires for LED fixture: Strip 1/4 of insulation from RED and BLACK wires. 5. Using #8 ( 1 1/2 ) wood screws provided, secure one flange to wall stud on non-wired side of closet. 6. Slide second flange onto rod with grooved side facing opposite wall. 7. Holding rod, lens, and loose flange in one hand, push RED solid wire push straight into LED terminal block opening with RED mark. Push BLACK solid wire straight into terminal with BLACK mark. (18/2 solid wire is recommended. If using 18/2 stranded wire, ends must be tinned. Depress terminal block tab with ball point pen and insert wire. 9. Partially fasten second flange to wall using ONE screw. Carefully position wires into one of the groves located on back of flange. Secure flange to wall with remaining screw, making sure wire is in flange groove. (If wires come through drywall and into the fixture, this step is not needed.) 10. Push rod against wall in non-wired flange and tighten set screw. 11. Cut Sempria WireWay to cover wires from flange exit to driver. Remove cover of WireWay and secure mounting base (wider piece) to wall with screws provided. Position wires inside base and snap cover (smaller piece) into place. Deburr all cut WireWay edges to protect wire insulation. NOTE: Maintain wire polarity. If fixture does not illuminate after making wire connections, reverse wires at driver. (A slight delay "on" is possible.) 32 LIGHTEDCLOSETROD-SPEC-0618 LIGHTEDCLOSETROD-SPEC

18 Puck LED Lighting with a slim profile for multiple applications Mini Can LED Lighting with a slim profile for multiple applications 5/8" Housing Section Cutout 1" Housing Section Cutout 2" 1 7/8" 3/4" 5/16" 2 1/4" Beam Spread Chart 2 1/4" Fixture Section 50,000 hour LED life at 70% lumen maintenance Surface or recess mount Frosted, light-diffusing lens 4 Watts per fixture 3-year limited warranty No UV or IR Dimmable (with compatible dimmer) Interior Cabinet Lighting Under Cabinet Lighting Display/Accent Lighting Dimensions: Construction Materials: Wattage: 2-1/4" x 2-1/4" diameter, 2" cut-out Cast Aluminum (heatsink), frosted glass 4 Watts CRI: 85+ Max Run: 2700K (Warm White) or 3000K (Soft White) 15 Volt DC Screws (included) Refer to driver specs 6 ft. Lead Wire Included Dry and damp locations Task Lighting retains the right to modify the design of our products without prior notice Puck Lights Fixture Section SPL9-FR-P-Finish-Temp 2700K, 3000K 210 Not recommended for sheetrock installation. Finish Options Black () Power Supplies / OUTPUT INPUT TLD-24WSI* 24W plug in 15V DC Plug In TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A *Call for dimming options Installation Components SP-20FT-18/2 SP-50FT-18/2 MAELV-600-Color MA-R-Color *WS-LED-CVD-902 *WS-SR-Color-902 Bronze (BZ) Satin Nickel (SN) 20 foot spool of 18/2 awg solid wire 50 foot spool of 18/2 awg solid wire 300W Diva slide dimmer 300W Diva slide dimmer 3-way Maestro electronic smart dimmer Maestro companion dimmer White () Sempria dimming module for wireless system Sempria wireless dimmer switch. Available in Black, Gray, Ivory, Light Almond, and White **NOTE: Call TASK for alternate driver Task Lighting retains the right to modify the design of our products without prior notice BEAM SPREAD 34 SEMPRIA-PUCK-SPEC-0618 SEMPRIA-MINICAN-SPEC ,000 hour LED life at 70% lumen maintenance Surface or recess mount 4 Watts per fixture 3-year limited warranty No UV or IR Dimmable (with compatible dimmer) Interior Cabinet Lighting Display/Accent Lighting Above Sink Lighting Dimensions: 2-1/4" x 2-1/4" diameter, 2" cut-out Construction Materials: Cast Aluminum (heatsink) Wattage: 4 Watts CRI: 85+ Beam Angle: Max Run: 2700K (Warm White) or 3000K (Soft White) 11, 20, or 38 degree beam spread 15 Volt DC Screws (included) Refer to driver specs 6 ft. Lead Wire Included Dry and damp locations Mini Cans SPMC-11-P-Finish-Temp 11º Spot 2700K, 3000K 240 SPMC-20-P-Finish-Temp 20º Narrow Flood 2700K, 3000K 240 SPMC-38-P-Finish-Temp 38º Flood 2700K, 3000K 240 Not recommended for sheetrock installation. Finish Options Power Supplies / OUTPUT INPUT TLD-24WSI* 24W plug in 15V DC Plug In TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A *Call for dimming options Installation Components SP-20FT-18/2 SP-50FT-18/2 MAELV-600-Color MA-R-Color Black () *WS-LED-CVD-902 *WS-SR-Color-902 Bronze (BZ) 20 foot spool of 18/2 awg solid wire 50 foot spool of 18/2 awg solid wire Satin Nickel (SN) 300W Diva slide dimmer 300W Diva slide dimmer 3-way Maestro electronic smart dimmer Maestro companion dimmer White () Sempria dimming module for wireless system Sempria wireless dimmer switch. Available in Black, Gray, Ivory, Light Almond, and White **NOTE: Call TASK for alternate driver

19 Puck/Mini Can Supporting Products Installation Instructions Installation Components 1-7/16 Call Task Lighting if you have any questions or need assistance. Power Supplies NEC All wiring must meet or local codes. The maximum wire length of the driver and fixture wire is 30 feet. Not recommended for sheetrock installation. PART NUMBER 1-7/8 TLD-24WSI* 3-1/4 TLD-24WSI / OUTPUT INPUT DIMENSIONS 24W plug in 15V DC Plug In 3-1/4 x 1-1/2 x 1-7/8 TLD-D30WSO 30W hardwire 15V DC, 2A max. 120V AC,.3A 8-1/8 x 2 x 1-3/4 TLD-D45WSO 45W hardwire 15V DC, 3A max. 120V AC,.4A 8-1/8 x 2 x 1-3/4 TLD-D60WSO 60W hardwire 15V DC, 4A max. 120V AC,.5A 8-1/8 x 2 x 1-3/4 TLD-D75WSO 75W hardwire 15V DC, 5A max. 120V AC,.6A 8-1/8 x 2 x 1-3/4 *Call for dimming options Constant Voltage Short circuit, over-load, voltage, and temperature protection High reliability, high efficiency UL listed Class 2 power supply 2 1 Determine exact location of fixtures and drill 2" diameter hole. Run fixture wires through the hole and feed them in the direction of the driver. 2 Connect RED driver wire with RED fixture wire using wire nuts provided. Repeat process with BLACK wires, making sure all connections are tight. 3 Squeeze wing tabs on side of fixture. 4 TLD-D30WSO TLD-D45WSO TLD-D60WSO TLD-D75WSO Insert fixture into hole. 1-3/4 8-1/8 Installation Components OPTIONAL: Surface Mounted Fixtures SP-20FT-18/2 20 foot spool of 18/2 awg solid wire SP-50FT-18/2 50 foot spool of 18/2 awg solid wire Magnetic Contact Switch Run fixture wires through the hole and feed them in the direction of the driver. Secure housing to surface with two screws provided. Follow steps #2 - #4 above. Driver MCS-10-BR 10W Max - Magnetic Contact Switch - Brown MCS-10-GR 10W Max - Magnetic Contact Switch - Gray MCS-10-10W Max - Magnetic Contact Switch - White MCS-100-BR 100W Max - Magnetic Contact Switch - Brown MCS-100-GR 100W Max - Magnetic Contact Switch - Gray MCS W Max - Magnetic Contact Switch - White Drawing shows wiring for two fixtures using wire nut connectors 36 S -P UC K / M I N I C A N - I NS TA L L MAELV-600-Color S E MP R I A - I NS TA L L AT I O N MA-R-Color 300W Diva slide dimmer 300W Diva slide dimmer 3-way MAELV-600-Color Maestro electronic smart dimmer MA-R-Color Maestro companion dimmer *WS-LED-CVD-902 Sempria dimming module for wireless system Sempria wireless dimmer switch. Available in Black, Gray, Ivory, Light Almond, and White **NOTE: Call TASK for alternate driver *WS-SR-Color

20 120V Bar Light 120V Bar Light Direct wire, easy to install bar light Installation Instructions 4-1/4" All installations must comply with national and local electrical codes. 1" 3" 1-1/4" Before installing, turn power off at main breaker panel. Section. xpose wiring compartment by inserting flat blade screwdriver between E housing and cover; Gently pry down to open. (Figure 1) Position fixture in mounting location to determine which knock-out to use. Linair 120V Bar Light 50,000 hr LED life at 70% lumen maintenance Integral Driver Easy open/close installation Multiple knockout locations (6) 3 Year limited warranty No UV or IR Dimmable (with compatible dimmer) LB9L10-5-P-Finish-Temp 10 x 4-1/4 x K 3000K 360 LB9L18-7-P-Finish-Temp 18-1/2 x 4-1/4 x K 3000K 720 LB9L27-11-P-Finish-Temp 27-1/4 x 4-1/4 x K 3000K 1080 LB9L36-15-P-Finish-Temp 36 x 4-1/4 x K 3000K 1440 Bronze (BZ) Under Cabinet Lighting Display Case Lighting Over Sink Lighting Satin Nickel (SN) Figure 2 Mount fixture with screws provided. (Figure 2) Secure ground wire (GREEN) to PEM stud marked with on fixture White () Using orange push connector provided, connect WHITE to WHITE wire from driver. (Figure 3) Optional Installation Components Using orange push connector provided, connect BLACK to BLACK wire from the 120V side of the fixture switch. (Figure 3) 320-C 3/8" Trade Romex clamp 6 ft. Hardwire power cord w/ ground. 18/3 SJB cord (for field installation only) Ensure all wires are pushed to inside of housing; snap cover shut. Black Cord 6FT Construction Materials: Extruded aluminum housing (heatsink), Impact Resistant Acrylic (lens), Powder coat finish 2700K (Warm White) or 3000K (Soft White) CRI: 90+ MACL-153M-COLOR Maestro LED Dimmer LED Beam Angle: MA-R-COLOR Preset Smart Remote (for multiple switching) 120º LED Spacing: 3" LED Board: 8-3/4" Power Rating: 130 V AC Max, 50/60 HZ Wood Screws (included) ga romex (3/8 Trade Romex, Clamp Included) Dry and damp locations Turn power on at main breaker panel. Switch Figure 3 tory n Fac nectio n o C 120 Vol t (Bla ck) 14/2 to 10/2 Neutral (White) Driver Task Lighting retains the right to modify the design of our products without prior notice 38 Install supplied conduit connector into knock-out. Secure wire. Connector may be used with: 3/8 trade sized reduced wall flexible steel or aluminum conduit, 14/2 to 10/2 non-metallic sheathed cable, or 14/2 to 10/2 steel armored cable. Finish Options LENGTH Figure 1 Ground Green MACL-153M-COLOR L I N A I R-BA RL I G HT- S P E C L I NA I R - B A R L I G HT- I NS TA L L