Installation Operation Maintenance Troubleshooting Version2.1. Feb/09. Led II

Transcription

1 Installation Operation Maintenance Troubleshooting Version2.1. Feb/09 Led II

2 INDEX Safety Regulation 3 Components 4 User s Guide 9 Product Installation 10 Operation Method 11 Maintenance and Repair 13 Head Tension 13 Head Tension Axle 2 14 Head Tension Axle 3 15 Inside Head Parts Replacement 16 Horizontal Arm Tension 17 Wiring Diagram & Product Specification 19 Maintenance 20 Storage 20 Warranty 21 2

3 SAFETY REGULATIONS * Check the condition of the power supply and the connecting parts * Led II is designed to make a clear vision for the doctor in the patient s oral cavity * The installation and use of the Led II is permitted only for an expert or licensed person * Use caution when using illumination of Led II, it may cause blindness * Prior to installation, ensure that the power is off & that the power cable is connected * The Led II should be installed using a power supply from a single-phase circuit * Inappropriate use of the Led II may cause harm to the patient or undesired effects * Keep the Led II & related components out of reach of children * Regular disinfection is required in order to prevent contamination * In case of disposal of Led II, ensure proper disposal of parts (i.e. Iron, Rubber, Plastic, etc.) CAUTION POINTS DURING INSTALLATION * Do not install device near standing water * Do not attempt to install the device in adverse conditions (i.e. Pressure, Tempreture, Humidity, etc.) * Vibration or constant shock of the Led II may impair the device s use * Do not store Led II near unsafe chemicals or flammable materials * Ensure proper voltage & power consumption * Make sure the earthing terminal is tightly connected with the earthing contact of appliance inlet 3

4 Before use, check the following points: - All cords are easily accessible - Adjust light patern in accordance with treatment environment - Check the condition of the lamp to ensure the replacement warranty During Use, check the following points: - Always monitor the device for abnarmalities - If a problem appears with the Led II, take immediate & appropriate action to ensure the patient s safety - Use of the Led II should only be conducted by expert or licensed individual COMPONENTS 4

5 COMPONENTS - HEAD 5

6 Item Code Number Item Description Qty Bezel Lens Cover Sense Cover Motion Sense Assembly Reflector Led PCB Top Cover Illumination Control Dial Handle R/L Handle Magnet Washer Handle Magnet Stoper R/L Head Arm Shaft R/L Head Arm Shaft Washer Logo Sticker Bolt Cap Flat Head Scew (M3 X 8L) Round Head Screw (M3 X 8L) Round head Screw (M5 X 10L) Socket Set Screw (M4 X 30L) Hexagon Nut (M4) Flat Head Screw (M2 X 8L) Round Head Screw (M3 X 10L) 4 6

7 COMPONENTS - HEAD 7

8 Item Code Number Item Description Qty First Head Arm Guide First Head Arm Body Head Arm Joint Pin Spindle 1 Washer Spindle Spindle Joint Pin Hexagon Socket Button Head Cap Screw Head Arm Joint Second Head Arm front Switch Power Switch Knob Plain Washer / Disc Spring / M10 Lock Nut Second Head Arm Rear Controler Board Bolt Cap Spindle Second Hear Arm Front Pin Spindle 3 Washer Plain Washer / WW20 Wave Washer / 1 M20 Lock Washer / M20 Lock Nut Hexagon Socket Flat Head Cap Screw (M5 X 15L) Head Arm Cap Round Head Screw (M3 X 10L) 4 8

9 USER S GUIDE Product Operating Order 1- The switch requires to be ON on the chair & on the Head Arm. 2- The height of head can be adjusted to focus a part of treatment region by using the head handle. 3- Set up the light intensity for treatment using the light intensity control dial & sensor detected. 4- During treatment adjust the position by using the Head Handle. 5- After use, power it off by pressing the power switch or light button of chair unit. Detachable Handle - using neodymiun magnet - Conveniently detachable, autoclavable, and pasteurizable for sanitary use. 9

10 PRODUCT INSTALLATION Check the product releasing condition, Head + First Level Arm, Combination R/L Handlebar, Second Level Arm. Wiring and connecting chair arm, second horizontal arm (rigid arm). Check the arm bolt size before installation. Connecting second horizontal arm (rigid arm) and first horizontal arm (flex arm) and head assembly Check the condition of the wire harness and connect the wires. Completion - Handle R/L (check direction of combinations) - Check for proper operation Caution - Avoid tension of wire - Avoid peeling of the paint on the arm 10

11 OPERATING METHOD - MOVING RANGE 11

12 OPERATING METHOD - MOVING RANGE 12

13 MAINTENANCE AND REPAIR - HEAD TENSION POSITION ZAKTON LLC Repair - Head (1 axle) tension control Check head 1 axle tension position Check the 2 handles connected R/L Side of first head arm. (neodymium magnet) Removal R/L Handle * Working method: Remove R/L Handle installed on first head arm. Caution: - Remove handles one by one. - Use of proper force. 1 axle tension control - Tool: long nose pliers - Working method: Adjust proper tension with long nose pliers. Caution: Fine adjusting should be done by one side. Use of proper force. Combination - Install handle as a final step. Caution: Make sure the handle is in the right direction. 13

14 REPAIR - HEAD (2 AXLE) TENSION CONTROL Check head 2 axle tension control - Check the joint part of first head arm and second head arm Check Head Arm Hole & Bolt Direction - Working method: Face Head Arm to the front side, make sure the side of Head Arm Hole and internal bolt are in the proper position. 2 axle tension control - Tool: Hexagon wrench (2.5 mm) - Working method: adjust tension by using the Hexagon wrench. 14

15 REPAIR - HEAD (3 AXLE) TENSION CONTROL Check head 3 axle tension control - Check the joint part of second head arm body. Check the lock nut of tension control - Tool: Philips screwdriver - Working method: check the lock nut, remove the rear of the second head arm with Philips screwdriver. 3 axle tension control - Tool: Long nose pliers. - Working method: adjusting tension with Lock nut. 15

16 MAINTENANCE & REPAIR - INSIDE HEAD PARTS REPLACEMENT Second Head Arm Rear Disasemble Tool: Phillips srewdriver, (or flat screwdriver) Working method: - Remove the Bolt Cap of the rear second head arm. - Remove the rear second head arm with a Phillips screwdriver. Caution: - Avoid scratching painting surface. - Be careful not to drop the back cover. Harness and Controller B/D Disassemble Tool: Phillips screwdriver, falt screwdriver. Working method: - To remove the harness use a flat screwdriver. - To take out controller board, use Phillips screwdriver. Replace circuit Working method: - Disconnect Wire that is connected with the circuit PCB. - Watch out the wiring while replacing the circuit PCB. Assembly: - Use the Reverse steps. 16

17 REPAIR - HORIZONTAL ARM (UP & DOWN) TENSION CONTROL Arm Cover Removal (common way) Tool: Flat scredriver (3 mm below) Working method: - Disassemble Cover using Flat screwdriver. Caution: Be careful with the paint surface to avoid breaking the hook on the cover. Common tension control method Tool: Hexagon wrench (3 mm) Working method: - Lower first horizontal arm as much as possible. - Fix Bolts on both sides as much as possible. Caution: - Fix the damper bolt. - Adjust the movement of the arm up & down by releasing the damper bolt. 17

18 REPAIR - HORIZONTAL ARM (UP & DOWN) TENSION CONTROL In case of less tension - Fix the tension control bolt (refer to the common tension control method) Tool: Hexagon wrench (3 mm) Working method: - Lower and tighten horizontal arm to the maximum then adjust it by loosening the bolt. - Tension Control Tool: Long nose pliers. Working method: Tension Control - Strong = The Hexagon nut is close to brass shaft. - Weak = Hexagon nut is far from brass shaft. - Final Step Tool: hexagon wrench (3 mm) Working method: - Lower horizontal arm as much as possible. - Loosen tension control bolt to adjust the surface level. 18

19 WIRING DIAGRAM & PRODUCT SPECIFICATION ZAKTON LLC Wiring Diagram Product Specification Categories Light Intensity Note Light Intensity 25,000 (Lux) Based on 70 cm distance from the source of light 10% Color Temperature 5,000 K +/- 5% CRI (Ra) 95 +/- 3 Focal Distance 70 cm - Pattern Size width: 15 cm x height: 9 cm - Power Consumption 12 W - Power Input AC 10~18V, 50/60 Hz - Led Life Span 50,000 Hours - 19

20 MAINTENANCE ZAKTON LLC Proper cleaning of device: Head Handle and other plastic: - Be sure to follow the manufacturer s instructions for use Metal Part (arm pipe & etc. ): - Use a dry cotton swab, moistened cloth to clean surface. LED Lens - Make sure residual material or debris are not on the surface of the lens - Remove residual material or debris by lightly rubbing with a micro fiber Cleaning and disinfection notice: - Use alcohol for disinfection - Use of thinner or petrolium material, could cause products discoloration - Avoid excessive use of disinfectant liquid (Influx or liquid in the appliance could cause problems) - Do not try to clean the device with water, to avoid damging the IPXO STORAGE Proper storage of the device is required. - Remove the power plug from the wall outlet. - Clean the Exterior including the lens surface from the dust. - Disassemble the product in an accordance with procedure provided in the Disassembly page. - Package well to prevent dust and other contaminants. - Store at room temperature in a non moist environment. - Store with care by a professional licensed person. 20

21 WARRANTY ZAKTON LLC warrants its products against defects in materials or workmanship from the date of shipment to the Buyer as follows: Zakton s Equipment: Chairs, Delivery Units, Cuspidors, Lights Control Block Diaphragm (part of Delivery Unit) All Upholstery, Stools, all Plastic Covers, and Cabinets Sterilizer/Autoclave Compressors, Suctions, X-Rays, Amalgamators, Ultrasonic Scalers, Light Cure units, Ultrasonic Cleaner, Apex Locator, Water Distiller Unit, Digital Sensor Warranty Period: 5 Years Lifetime 1 Year 2 Years 1 Year Zakton s sole obligation under the warranty is to provide parts for repair, or at its option, to provide a replacement product (excluding all labor and shipping fees). In any action, BUYER S remedies are limited to the warranty described above. BUYER shall not be permitted to claim lost profits, reliance, special, incidental, or consequential damages in any proceedings. The warranty does not cover damage from improper installation or maintenance, accident or misuse. The warranty does not cover damage resulting from the use of cleaning disinfecting or sterilization chemicals and processes. Failure to follow instructions provided in Zakton s Operation and Installation Manuals (Owner s Guides) may void the warranty. In the event Warranty service must be performed to correct any defect, only an authorized Zakton s dealer may perform any and all warranty repairs. Any repairs by unauthorized dealers, technicians, or repairmen may void the warranty. In the case of a defective warranty item, a copy of the replacement invoice, model and serial number of the product under which it was replaced, and a description of symptoms of the defect must be returned with the part within 30 days of the replacement invoice date to Zakton, 3460 S. Federal Blvd- #D Sheridan Colorado 80113, USA, in order to receive credit. Any and all expenses for freight, labor to perform warranty service, and purchase of spare parts are the responsibility of the buyer. Any fraudulent claims made may void the warranty. Any additional warranty that may be provided by an authorized Zakton s dealer is the sole responsibility of said dealer. Zakton reserves the right to make changes or improvements on any products without being required to modify existing equipment in a like manner. Please complete and retain for your records the following Information: In case of warranty part replacement/ repair or when ordering a part, please call your authorized Zakton s dealer and have the following information available. Owner s Name: Phone #: Model #: Zakton s Serial #: Dealer Name: Phone #: Purchase Date: 21

22