INSTALLATION GUIDE GVM5611 SELF SUPPORTING STAND FOR DODGE CHARGER. pro-gard.com STRONG RELIABLE SECURE
|
|
- Dale Thompson
- 5 years ago
- Views:
Transcription
1 INSTALLATION GUIE GVM5 SELF SUPPORTING STAN FOR 0-0 OGE HARGER STRONG RELIALE SEURE
2 THESE OMPONENTS ARE REQUIRE TO INSTALL THE PRO-GAR GVM5 SELF SUPPORTING STAN AN TRI-LOK GUN RAK G5-0 MOUNT ASE Tri-Lock Gun Rack GVPMXXXX I. Refer to the diagram on the last page of these instructions to verify all parts were received. II. The following tools will be required to complete the installation. A. / Socket & Ratchet. / Allen Wrench. 5/ Allen Wrench. / Socket III. Installing the self supporting stand. A. Losen the inner rear seat track bolts for the passenger and driver front seat. NOTE: It unneccassary to remove the bolts completly.. Orient the Mounting ase (G5-0) so that the legs face towards the front of the vehicle. Slide the legs of the base under the front seat tracks, aligning the nothes with the Seat bolts and alingment pins. Leave loose. (See Fig. ). Using the supplied Self Tapping Screws (X5) ancor the rear of the Mounting base to the Rear Seat Area.. Tighten the OEM Front Seat olts. Note: No torque spec reqiured. FIG. PASSENGER SIE SHOWN IV. ase Installation omplete (ontinue with The Gun Rack Installation) OEM SEAT OLT FORWAR OEM SEAT RAIL
3 V. Installing the Tri-Lock gun rack (Requires Pro-gard self-supporting mounting base) A. Place the intended guns into the gun rack and make adjustments to fit. This will allow more access than when the rack is in the vehicle, but the rack can be adjusted after installed inside the vehicle as well.. The brackets mounting the gun lock are designed to be loosened and adjusted in many directions to accomodate most guns. Fit each gun by loosening the bolts on the gun lock bracketry so the mounting bracket moves freely. Place your gun into the lock and in the desired position. Take a allen wrench to tighten locks in place. (See Fig. ) Locks move up and down Tilts clockwise or counter clockwise ompleted Gun Fitment The shot gun shown in the lower position with insert Left and right Fig. Gun locks should open and close easily and guns should pull in and out of the rack with no issues when properly installed. Shot Gun Mounting - The shot gun can be mounted in two ways, by barrel mount or by installation of the shot gun mount insert. To install the shot gun insert, remove the standard insert by opening the lock and unscrewing the two insert bolts with an allen wrench. Remove the retaining ring from the bolt s back side. Replace with shot gun insert (G) and reinstall insert bolts and retaining rings on the back side of the insert. Use the two fastener bolt s adjustment to fit the shot gun used in the lock. (See Fig. ) A Step Remove barrel bracket Step Remove standard insert Step Replace with shot gun insert A arrel mounting bracket Fig. Standard insert Shot gun insert Retaining ring
4 VI. Self-Supporting Installation A. For self-supporting installations, remove the four bolts that secure the butt plates to the base of the gun rack. Then rest the gun rack to the self supporting stand, loosely attach the gun rack and adjust it and the butt plates as necessary from front to back. (See Fig. ) NOTE: For Optimal onditions secure the back of the gun rack tigth against the seat. VII. Lock ox A. Open the lock box and loosen the bolts with a / socket and extension wrench to adjust the box up or down as needed. (Swivel attachment is required) Install supplied black felt over bolts when box position has been fixed. (See Fig. 5) Adjustable hole locations to provide the best mounting preference. Lock box adjustment bolts Fig. Fig
5 VIII. Gun lock switch and timer installation. A. We suggest mounting the momentary release button in a concealed location that can be easily reached by the officer, but would be hidden in case an unathorized entry occurs.. onnect the gun lock wiring as shown in the diagram below. NOTE: Pro-gard requires the use of a 0 AMP fuse between the power source and gun lock circuit or the warranty will be voided! IX. Lock Head Operating Instructions Fig. A. To release, grasp the weapon, but do not pull it against the lid of the gun lock.. While depressing and holding the release button (momentary switch), push and then pull the weapon towards the lid of the gun lock to release it from the lock. NOTE: TIP: One handed operation is possible utilizing the optional second timer. The timer will unlock the lock for seconds following activation of the momentary switch. If the gun is not pulled out of the lock within seconds after activation of the momentary switch, the lock will automatically re-lock. If lid of the lock does not release, press in on the lid to release tension and reactivate the release button (unless timer is still active). Installation omplete! all Pro-gard technical support if assistance is needed
6 Self-Supporting Mounting ase G5-0 PART NUMER ESRIPTION G5-0 SELF SUPPORTING ASE G50 SELF SUPPORTING LEG, LEFT G50 SELF SUPPORTING LEG, RIGHT HARWARE KIT PART NUMER ESRIPTION X5 / X " SELF RILLING HEX HS
7 Tri-Lock Gun Rack PARTS LIST PART NUMER ESRIPTION GVM0-0 RAK ASE WELMENT * GVM00-0 **G-00.5" X.5" X " LG. ALUM EXTRUSION UTT PLATE - LAK NYLON * **G-00 RUER UTT PLATE PA 5 * GVM0-0 LOK MOUNTING RAKET - PASSENGER * GVM0-0 LOK MOUNTING RAKET - RIVER * * **G0-NPG **G5 G00 R GUN LOK R LOK ARREL MOUNT RAKET UPPER PARTITION MOUNTING RAKET A * * * G0 LOWER PARTITION MOUNT RAKET (NOT SHOWN) G LOK INSERT FOR SHOT GUN PART NUMER GL0 GUN SAFE GVM0-0 HARWARE LIST GVM00-0 PART NUMER ESRIPTION X 5/- X / SHS, K G-00 X / FLAT WASHER, LAK G-00 X5 /-0 X 0.5 SHS 5 GVM0-0 X5 /-0 SLOT NUT (NOT SHOWN) X / FLAT WASHER, LAK GVM0-0 X /-0 x " HHMS, Zn G0-NPG X /-0x0.5, SHS, LAK OXIE G5 X /-0 X / ARRIAGE OLT XZ /-0 WHIZ NUT G PLAIN EXTRUSION EN AP 0 G0 X /-0 WHIZ NUT (NOT SHOWN) G X5 5/- X 0. LG. SHS, K X - SLOT NUT GL0 N00-TH NEOYMIUN MAGENT X - X 5/ FHSS PART NUMER X /-0 X 0.5 HEX AP SREW X 0.5 RIVET (NOT SHOWN) X G50R LAK FELT /" X " ONSUME (NOT X SHOWNT) G50R-0 LOK OX FELT (NOT 5 SHOWN) G500 MOMENTARY SWITH G00 TIMER ELAY MOULE * - MAY VARY EPENING ON ONFIGURATION ** - MAY VARY EPENING ON ONFIGURATION 0 X5 X5 X X X X XZ A 050-PLAIN 5 5 X X5 X N00-TH X X X G50R G50R-0 A
INSTALLATION GUIDE GVM8116FT SELF SUPPORTING STAND FOR 2016 FORD F150 4-DOOR. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIE GVMFT SELF SUPPORTING STN FOR 0 FOR F0 -OOR STRONG RELILE SEURE THESE OMPONENTS RE REQUIRE TO INSTLL THE PRO-GR G0 SELF SUPPORTING STN N TRI-LOK GUN RK Tri-Lock Gun Rack GVPMXXXX GFT Self
More informationinstallation Guide self supporting stand for chevrolet tahoe pro-gard.com Strong Reliable Secure
installation Guide GVM55 self supporting stand for 05 + chevrolet tahoe Strong Reliable Secure 00.0.0 PRT NUMER G55U-0 G55U-05 G55U-0 PRT NUMER X0 X G55U TRI-LOK SELF SUPPORTING SE SET MOUNTING RKET -
More informationINSTALLATION GUIDE 3G7047 & 3G7009A SELF SUPPORTING GUN RACK FOR FORD UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIE G0 & G00A SELF SUPPORTING GUN RAK FOR 0+ FOR UTILITY INTEREPTOR STRONG RELIALE SEURE THESE OMPONENTS ARE REQUIRE TO INSTALL THE PRO-GAR G0 SERIES WEAPONS SYSTEM G00A GUN RAK & G0 GUN
More informationINSTALLATION GUIDE GTM5617 TRUNK MOUNTED GUN RACK DOGDE CHARGER. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE GTM5617 TRUNK MOUNTED GUN RACK 2015-2017 DOGDE CHARGER STRONG RELIABLE SECURE pro-gard.com 800.480.6680 THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD GTM003 GUN RACK GTM5617
More informationINSTALLATION GUIDE P1000T15A PRO-CELL CURRENT TAHOE. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIE P000T PRO-ELL 0 - URRENT THOE STRONG RELILE SEURE 00.0.660 THESE OMPONENTS RE REQUIRE TO INSTLL THE PRTITION WXXXT river & Passenger Window ars Pro-ell Kit Wing Kit P000T / age Partition
More informationINSTALLATION GUIDE CARGO BARRIER CURRENT FORD UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE CARGO BARRIER 0 - CURRENT FORD UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD BARRIER SYSTEM B00 BARRIER B7 HARDWARE/WING KIT I. Refer
More informationINSTALLATION GUIDE WSD47UINT13 WEAPON STORAGE DRAWER & ASBD47UINT13 ALUMINUM STORAGE DRAWER CURRENT FORD UTILITY INTERCEPTOR
INSTALLATION GUIDE WSD7UINT WEAPON STORAGE DRAWER & ASBD7UINT ALUMINUM STORAGE DRAWER 0 - CURRENT FORD UTILITY INTERCEPTOR STRONG RELIABLE SECURE 800.80.80 THESE COMPONENTS ARE REQUIRED TO INSTALL THE
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUTS, INSTALLATION INSTRUTIONS PRO TRAXX 4 OVAL TUE STEP AR APPLIATION: 2014+ hevrolet Silverado / GM Sierra 1500 Double / rew ab 2015+ hevrolet Silverado / GM Sierra 2500/3500 HD Double
More informationZ125 Front Fork Upgrade kits. Installation SOP
Z125 Front Fork Upgrade kits Installation SOP Tools a. Loctite243 or Loctite2701 (Thread Locker) b. Loctite7649 (Activator) c. 33mm Hex Socket d. 17mm Hex Socket e. Shaft Clamping Tool (12mm) f. Shaft
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationINSTALLATION GUIDE 4PK57SS15 SPACE SAVER PLUS PARTITION CURRENT TAHOE & 2016 SILVERADO. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIDE PK7SS SPE SVER PLUS PRTITION 0 - URRENT THOE & 0 SILVERDO STRONG RELILE SEURE 00.0.0 THESE OMPONENTS RE REQUIRED TO INSTLL THE PRTITION Space Saver Plus Partition Hardware Kit Wing Kit
More informationFord C4 and C6 Floor Mount Automatic Transmission Shifter Installation Instructions
Ford C4 and C6 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C4 and C6 Mount
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2009-2018 Dodge Ram 1500 (Excl. Rebel Model) 2019 Dodge Ram 1500 Classic PART NUMBER: 32-1960, 32-1965, 32-1960L, 32-1965L
More informationI-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationINSTALLATION GUIDE PRISONER TRANSPORT LIGHTING. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE PRISONER TRANSPORT LIGHTING STRONG RELIABLE SECURE pro-gard.com 800.480.6680 THESE COMPONENTS ARE REQUI TO INSTALL THE PRO-GARD PRISONER TRANSPORT LIGHTING 3" Round LED Lighthead QTY=
More informationChrysler 727, 904, 518 Floor Mount Automatic Transmission Shifter Installation Instructions
Chrysler 727, 904, 518 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Button
More informationFig A. Addictive Desert Designs. Preparation: Removal:
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationFord AOD-4R70W-AODE Cable Operated Shifter Installation Instructions
Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable
More informationFord AOD-4R70W-AODE Cable Operated Shifter Installation Instructions
Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal: Release these clips
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationINSTALLATION GUIDE P1000T15AOSB CHEVY TAHOE. pro-gard.com RELEASED STRONG RELIABLE SECURE
INSTLLTION GUIDE P000T5OS 05-09 HEVY THOE STRONG RELILE SEURE RELESED 0.9.0 pro-gard.com 00.0.660 THESE OMPONENTS RE REQUIRED TO INSTLL THE PRTITION WXXX57T5 Driver & Passenger Window ars Pro-ell Kit Wing
More informationJeep Wrangler Unlimited (JK) 2007 up A 2-Door. 3-5 Hours INSTALLATION GUIDE INSTALLATION TIME SKILL LEVEL. 4= Experienced TOOLS REQUIRED
INSTALLATION GUIDE APPLICATION AMP Part # Jeep Wrangler Unlimited (JK) 2007 up 751-01A 2-Door INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced TOOLS REQUIRED
More informationGM Floor Mount Automatic Transmission Shifter Installation Instructions
GM Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com GM Mount Automatic Transmission
More informationChrysler 45RFE Tailmount Automatic Transmission Shifter Installation Instructions
Chrysler 45RFE Tailmount Automatic Transmission Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Chrysler 45RFE Tailmount
More informationINSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)
INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing
More informationTH200 & TH200-4R Automatic Trans Mount Shifter Installation Instructions
TH200 & TH200-4R Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com
More information2014 Current Chevy/GMC 1500 HoneyBadger Rear Bumper Installation Instructions
2014 Current Chevy/GMC 1500 HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationJEEP Wrangler V6-3.8L
63-1574 JEEP 2007-11 Wrangler V6-3.8L NOTE: This kit was not designed to fit vehicles with a body lift. AQ AR AR AP AN A E AO AJ AI AM AH AL AK K AF A AE A A A F AA Z J I H M N M P Q AS O V W R Y S R X
More informationOPERATING INSTRUCTIONS FOR. Gold-Place TM. Manual Pick & Place with Dispenser System Model MPP-21
OPERATING INSTRUCTIONS FOR Gold-Place TM Manual Pick & Place with Dispenser System Model MPP-21 AUTOMATED PRODUCTION SYSTEMS, INC. 2840 Pine Road Huntingdon Valley PA 19006 Phone: (215) 938-1000 FAX: (215)
More information4L80E Automatic Trans Mount Shifter Installation Instructions
4L80E Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com 4L80E Automatic Trans Mount Installation
More informationINSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT
INSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT P FRONT 1 with MFK 4 for 2008 2019 CHEVROLET PASSENGER VANS W/DUAL SIDE SWING OUT DOORS P FRONT 2 with MFK 8 for 2008 2019 CHEVROLET
More informationPowerglide Automatic Floor Mount Shifter Installation Instructions
Powerglide Automatic Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com Powerglide
More information2011-up Polaris RZR 800* Cab Enclosure Kit. Caution: Before using this product, read this manual and follow all safety instructions.
Owner s Manual Model: Polaris RZR * 2011-up Polaris RZR 800* Cab Enclosure Kit Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions Kit Contents
More informationInstallation Instructions PowerBoard Automatic Retracting Running Board
Installation Instructions PowerBoard Automatic Retracting Running Board Vehicle Application Dodge Ram 1500 Crew Cab 2009 - Current : 75138-15 Dodge Ram 2500/3500 & HD Crew Cab 2010 - Current : 75138-15
More informationCHEVY SILVERADO CREW CAB RX3 Includes models equipped with DEF tank
2007-2017 CHEVY SILVERADO 1500-3500 CREW CAB RX3 Includes models equipped with DEF tank HARDWARE INCLUDED RECOMMENDED TOOLS 1 Passenger Side Front Support Plate 13mm Wrench 1 8-1.25 x 40mm Hex Bolt 13mm
More informationChrysler 727, 904, and 518 Automatic Trans Mount Shifter Installation Instructions
Chrysler 727, 904, and 518 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Chrysler 727, 904, and
More informationFord C6 Automatic Trans Mount Shifter Installation Instructions
Ford C6 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C6 Automatic Trans Mount Installation
More informationSelf-Deploying Rail Kit OEM INSTALLATION MANUAL
Self-Deploying Rail Kit OEM INSTLLTION MNUL TLE OF ONTENTS Introduction 2 Safety Information 2 Resources Required 3 Prior to Installation 3 Installation 3 Doorjamb 3 Setting the Doorjamb 3 inch Latch 4
More informationINSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
INSTALLATION GUIDE APPLICATION MODEL YR PART # Dodge Ram Quad Cab 1500 2009 - up 7513-01A Dodge Ram Crew Cab 1500 2009 - up 75138-01A Dodge Ram Crew Cab 2500/3500 2010 - up 75138-01A Dodge Ram Mega Cab
More informationAutomatic Electronic Sport Mode Shifter Installation Instructions
Automatic Electronic Sport Mode Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Automatic Electronic Sport Mode
More information2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware
Owner s Manual Model: Polaris RZR * 2008~2010 Polaris RZR 800* Cab Enclosure Kit Slam latch hardware Caution: Before using this product, read this manual and follow all safety instructions. Safety Instructions
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS OUTLAW REAR BUMPER APPLICATION: 2016-2018 Chevrolet Silverado 1500 PART NUMBER: 58-81005 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 REAR BUMPER 18MM WRENCH 2 4 SENSOR
More informationDriver Side Support Bracket pictured in "no-tow hook" direction. Reverse direction for tow hook equipped vehicles
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions
More information2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions
2017 Current Ford SuperDuty Adaptive Cruise Control Relocation Bracket Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set
More informationParts List. Item Qty. Part # Description Item Qty. Description Torque
Installation Instructions BR20 Rear Bumper Replacement Part Number 28171T Chevrolet Silverado 1500 2/4WD Parts List Item Qty. Part # Description Item Qty. Description Torque 1 1 28171T0AA Bumper Replacement
More informationInstallation Guide Philips MP90 VHM Wall Mount Kit
Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series
More informationTH400 Automatic Trans Mount Shifter Installation Instructions
TH400 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com TH400 Automatic Trans Mount Installation
More informationInstallation Instructions For Part Number: Scoop and Snorkel Kit
Installation Instructions For Part Number: 883-275 Scoop and Snorkel Kit 2008-14 Polaris Ranger RZR 800 800 E.F.I. Tools Required For Installation: 7/16 and 1/2 Wrenches. 10mm, 7/16, and 1/2 Sockets. T-25
More information2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions
2017 Current Ford Raptor HoneyBadger Rear Bumper Installation Instructions PREPARATION 1. Disconnect the negative terminal on the battery. Park the vehicle on level ground and set the emergency brake.
More informationTH350 Automatic Trans Mount Shifter Installation Instructions
TH350 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com TH350 Automatic
More informationMultistrada (MTS) Tank Installation Notes. Tools Required. Phase 1: Remove Fairings. Phase 2: Remove Fuel Tank
The California Cycleworks MTS tank provides an aftermarket alternative to the OEM nylon fuel tanks as used on aircooled Desmodue Ducati Multistrada 1100, 1000, and 620 models. This fuel tank is NOT for
More informationGun Racks. Tri-Lock Weapon Mounting System. Shown in a Chevrolet Tahoe
Gun Racks Tri-Lock Weapon Mounting System Shown in a Chevrolet Tahoe Tri-Lock Weapon Mounting System Pro-gard s Tri-Lock Weapon Mounting System easily accommodates your officer s weapon regardless of the
More informationINSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES)
LIFT CORPORATION Sht. 1 of 22 DSG# M-16-32 Rev. - Date: 12/13/16 INSTRUCTIONS, (FORD) SUPER DUTY INSTALLATION KIT (C2 PICKUP LIFTGATES) FORD SUPER DUTY F-250, F-350 & F-450 PICKUP TRUCKS, 2017 MODEL KIT
More informationSINGLE GUN RACK - VERTICAL
SINGLE GUN RACK - VERTICAL PARTITION MOUNTED - ORDERING OPTIONS 475-0850 GR3-AR-GL3XL 475-0851 GR3-870-GL3XL 475-2014 GR9-870 475-2015 GR9-AR-BLM DUAL GUN RACK - VERTICAL PARTITION MOUNTED - ORDERING OPTIONS
More informationInstallation Guide GE Healthcare Carescape Dual Display Roll Stand Kit
Installation Guide GE Healthcare Carescape Dual Display Roll Stand Kit The purpose of this guide is to describe assembly of the Roll Stand. WARNING - EXCESSIVE LEAKAGE CURRENT - DO NOT use multiple socket
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2017 Ford F-250/350 PART NUMBER: 32-3900, 32-3905, 32-3900L, 32-3905L ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 ULTIMATE
More informationHOUSTON OILFIELD EQUIPMENT 9669 PORT ERROLL RD. HOUSTON, TX PHONE: (713) FAX: (713)
HOUSTON OILFIELD EQUIPMENT 9669 PORT ERROLL RD. HOUSTON, TX 77095 PHONE: (713) 466-3797 FAX: (713) 466-3189 INSTALLATION AND MAINTENANCE INSTRUCTION MANUAL 10M CWP H-JWAl HPC ADJUSTABLE CHOKE AND POSITIVE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS WJ2 FULL-WIDTH FRONT BUMPER APPLICATION: 2018 Jeep Wrangler JL PART NUMBER: 59-80105, 59-80115, 59-80125 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 FRONT BUMPER ASSEMBLY
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS --1075 North Ave. Sanger, CA 93657-3539 local: 559-875-0222 fax: 559-876-2259 toll free: 800-445-3767-- 2505 Lowering Spindle Assembly Installation Instructions ½ TON SILVERADO
More informationRev. B Page 1 of 7 SPEC. ASSY INST, REMOTE ADJUSTABLE PRE-LOAD (30-25XX & SA XX)
Page 1 of 7 SPEC. ASSY INST, REMOTE ADJUSTABLE PRE-LOAD (30-25XX & SA-5057-5XX) 19 3 10 11 4 7 20 16 14 15 12 13 21 5 9 6 17 2 1 Fig. 1 Reservoir Components Fig. 2 Housing Components 30-25XX & SA-5057-5XX
More informationInstallation Manual for VHM-25 Series Arms Channel Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for VHM25 Series Arms Channel Mount Install Time: 1015 minutes The purpose of this manual
More information2010 CAMARO COG DRIVE UPGRADE Installation Instructions
2010 CAMARO COG DRIVE UPGRADE Installation Instructions 2010 CAMARO SS (LS3 & L99) P/N: 4GE118-010, 4GE118-020, 4GE118-030 ENGINEERING, LLC 1650 Pacific Avenue, Channel Islands, CA 93033-9901 Phone 805
More informationFig A ADDICTIVE DESERT DESIGNS. Preparation: Removal:
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More information1. Single-speed bicycle (SSB) lower fork legs... Page 3 2. Multi-speed bicycle (MSB) lower fork legs... Page 4
TM owner s instruction manual the ULTIMATE SURFBOARD RACK I. Messages & Warnings...Page 2 II. FORK BASE UNIT COMPONENTS...Page 2 III. SELECTING PROPER LEG TYPE...Page 2 IV. LEG LENGTH ADJUSTMENT & FORK
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Product Notepad V - Universal Cradle & Accessories Rev. F INST-479 7160-0250 Notepad V Universal Cradle 7160-0250-01 Notepad V Universal Cradle w/tall Side Clips 7160-0250-02
More informationHiBoy Maverick/Commander Doors Part # HiBoy4 Maverick/Commander Doors Black
Racing 3191 N Washington St. Suite 2 Chandler, AZ 85225 1 (800) 708-9803 http://www.racing.com HiBoy Maverick/Commander Doors Part # 07-2001 HiBoy4 Maverick/Commander Doors Black Congratulations on your
More informationHUMMER H A. 3-5 Hours INSTALLATION GUIDE INSTALLATION TIME SKILL LEVEL. 4= Experienced TOOLS REQUIRED APPLICATION MODEL YR PART #
INSTALLATION GUIDE APPLICATION MODEL YR PART # HUMMER H2 2003-2009 75107-01A INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 = Experienced TOOLS REQUIRED Safety goggles
More informationINSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document#
d INSTALLATION INSTRUCTIONS Mitsubishi Lancer Evolution VIII / IX Fuel Surge Tank Kit Document# 19-0077 Brie Tech Support: info@radiumauto.com CAUTION: Exercise extreme caution when working with the fuel
More informationADDICTIVE DESERT DESIGNS
Preparation: Disconnect the negative battery terminal. Park the vehicle on level ground and set the emergency brake. We recommend reading through the installation instructions in whole before performing
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS OUTLAW REAR BUMPER APPLICATION: 2013-2018 Dodge Ram 1500 PART NUMBER: 58-81025 CONTENT ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 REAR BUMPER 18MM WRENCH 2 4 SENSOR L-TAB 5MM
More informationKit No Please read these instructions completely before proceeding with installation. Air Spring Kit Parts List. Bracket Attaching Hardware
Kit No. 59532 MN-572 (021108) ECR 7136 Please read these instructions completely before proceeding with installation Air Spring Kit Parts List A Item Description Quantity A Air Sleeves 2 B Upper Brackets
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationFlat Front Clip Clip Guide Lockable Latch Tee Nut Offset Front Clip
INSTALLATION INSTRUCTIONS Product Revision Form Notepad V - Universal Cradle & Accessories Rev. D INST-479 7160-0250 Notepad V Universal Cradle 7160-0250-01 Notepad V Universal Cradle w/tall Side Clips
More informationInstallation Instructions HURST STAGE 1 SPRING KIT Chevrolet Camaro SS Fits: Coupe and Convertible Catalog #
Installation Instructions HURST STAGE 1 SPRING KIT 2016-2017 Chevrolet Camaro SS Fits: Coupe and Convertible Catalog # 6130001 WORK SAFELY: Installation of any Hurst Spring Kit should be performed ONLY
More informationModels Affected: Certain 2015 & 2016 All American Front Engine and Vision Buses Equipped with Hydraulic Brakes ISSUE _ CORRECTIVE ACTION _
R E C A L L C A M P A I G N -- R 1 4 X R ---- Models Affected: Certain 2015 & 2016 All American Front Engine and Vision Buses Equipped with Hydraulic Brakes ISSUE _ CORRECTIVE ACTION -- -- _ The parking
More informationEASYBIRD AUTO-FEED 6 - PACKER Part No (40912 with Oscillating Base)
EASYBIRD AUTO-FEED 6 - PACKER Part No. 40911 (40912 with Oscillating Base) Instruction Manual WARNING! THIS MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. THOROUGHLY READ INSTRUCTIONS BEFORE INSTALLING OR
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More information700-R4, 4L60, and 4L60E Automatic Trans Mount Shifter Installation Instructions
700-R4, 4L60, and 4L60E Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com 700-R4, 4L60, and 4L60E
More informationINSTALLATION MANUAL
INSTALLATION MANUAL 1500350 Parts List 1 Driver / left inner fender liner 1 Passenger / right inner fender liner 4 Z-hanger brackets 1 Thread-set bolt, M6 1 Thread-set washer 1 Thread-set spacer 22 Hex
More informationALL700RM-230V INSTALLATION INSTRUCTIONS
ALL700RM-230V INSTALLATION INSTRUCTIONS Aladdin Light Lift, Inc. (256) 429-9700 61 Shields Road (877) 287-4601 Huntsville, AL 35811 www.aladdinlightlift.com Patent #5105349 WARNING: Disconnect power source
More informationINSTALLATION GUIDE. AMP RESEARCH TECH SUPPORT (Press 2) Monday - Friday, 6:00 AM - 5:00 PM PST
INSTALLATION GUIDE APPLICATION MODEL YR PART # Dodge Ram Quad Cab * 1500 2009 - up 75138-01A Dodge Ram Crew Cab 1500 2009 - up 75138-01A Dodge Ram Crew Cab 2500/3500 2010 - up 75138-01A Dodge Ram Mega
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS HDX DROP STEP APPLICATION: 2007-2017 Chevy Silverado / GM Sierra / 1500-2500-3500 Ext. / Double / Crew Cab PART NUMBER: 56-13715, 56-13725 ITEM QUANTITY DESCRIPTION
More informationFord AOD, 4R70W, and AODE Automatic Trans Mount Shifter Installation Instructions
Ford AOD, 4R70W, and AODE Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD, 4R70W, and
More informationInstallation Instructions Camaro ZL1 ( Z) ( ZB)
Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationINSTALLATION INSTRUCTIONS PROTRAXX 5
AUTOMOTIVE PRODUCTS, INSTALLATION INSTRUCTIONS PROTRAXX 5 APPLICATION: 2009-2015 Dodge Ram 1500 Crew Cab/Quad Cab 2010-2015 Dodge Ram 2500/3500 HD Crew Cab PART NUMER: 21-53550, 21-53555, 21-53560, 21-53565
More informationImportant: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE
TITAN pt. no.: 03 0000 0128 Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION GUIDE 30 Gallon* Spare Tire Auxiliary Fuel
More informationInstallation Instructions
Powerglide Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com Powerglide
More informationH15P. Toyota Hilux A-DECK Dual Cab
Toyota Hilux A-DECK Dual Cab Page 1 of 14 Fitting Instructions Part Number H15 Toyota Hilux A-DECK Dual Cab 2015+ To suit Sports Bars Check contents of kit before commencing fitment and report any discrepancies
More informationINSTALLATION GUIDE. High Steer Kit
AEV30212AE Last Updated: 12/09/16 High Steer Kit Designed for 2007 current Jeep JK Wrangler and Wrangler Unlimited models in all trim levels, including Rubicon, with at least 3.0 of suspension lift. INSTALLATION
More informationSS71R SAFARI R-SPEC SNORKEL Toyota Land Cruiser LJ70 Bundera 2.4L 4cyl Turbo Diesel (2L-T engine)
SS71R SAFARI R-SPEC SNORKEL Toyota Land Cruiser LJ70 Bundera 2.4L 4cyl Turbo Diesel (2L-T engine) 01/04/2015 Parts List ITEM PART NO DESCRIPTION QTY 1 330-133-000R BODY - SNORKEL 1 2 000-135-050 3" AIR
More informationTABLE OF CONTENTS. Ram Assembly
TABLE OF CONTENTS DUC Cover------------------------------------------------------------------------------------ 00 Table of Contents----------------------------------------------------------------------------
More informationREPAIR AND MAINTENANCE MANUAL
REPAIR AND MAINTENANCE MANUAL Index Section I Suggested Tool Kit Page 2 Section II List of Commonly Replaced Parts Page 3 Section III Cables Page 4-7 Section IV Cable Handles Page 8 10 Section V Casters
More informationRam 1500 Crew Cab A Ram 2500/3500 Crew Cab A
I N S T A L L A T I O N G U I D E APPLICATION AMP Part # Ram 1500 Crew Cab 2013-2015 77138-01A Ram 2500/3500 Crew Cab 2013-2015 77138-01A Note:The application works only on the Crew Cab model Vehicles.
More informationInstallation Guide. Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit
Installation Guide Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter. 2. Describe attachment of Mounting
More informationInstallation Instructions - D-Series Warming Cabinet Instruction Door for Hinge UseReversal (Glass and Stainless Steel Doors)
Header Cam Lock Reversal... pg 1-4 Glass Door hinge reversal..... pg 5-9 Steel Door hinge reversal..... pg 10-13 Remove Panels Before reversing door hinges, the Header Cam Lock assembly must be reversed.
More informationVan Rack Installation Manual Dodge ProMaster
1.888.772.8400 Big to small... We do it all Van Rack Installation Manual Dodge ProMaster Thank you for your purchase of an Unruh Fab Van rack. We have designed and built this rack so that you can easily
More information