INSTALLATION GUIDE 3G7047 & 3G7009A SELF SUPPORTING GUN RACK FOR FORD UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
|
|
- Dylan Nichols
- 5 years ago
- Views:
Transcription
1 INSTALLATION GUIE G0 & G00A SELF SUPPORTING GUN RAK FOR 0+ FOR UTILITY INTEREPTOR STRONG RELIALE SEURE
2 THESE OMPONENTS ARE REQUIRE TO INSTALL THE PRO-GAR G0 SERIES WEAPONS SYSTEM G00A GUN RAK & G0 GUN RAK MOUNT ASE I. Refer to the diagram on the last page of these instructions to verify all parts were received. II. III. The following tools will be required to complete the installation. Socket Wrench with mm, mm, / & / sockets. Phillips screw driver. Installing the gun rack. A. Loosen both inner rear seat bolts of the driver and passenger seat so that the seats can be lifted about /. Then install the mounting base (G0-0) by pushing the front seats forward. Then slide the arms of the mounting base under the seat frame. Once the arms of the mounting base are slid into place tighten the two seat bolts. (See FIG.). Locate the rear seat bolts and studs that secure the back seat. The bolts and studs are located in the front of the rear seat. The bottom of the seat has a skirting around it and that will will need to be pulled loose at the bottom. Once the skirting is lifted up at the bottom the bolts and studs will be located there. The bolts and studs are mm and they will need to be loosen so that the seats can be lifted about /. See Fig. Then install the rear support bracket by pusing the seats backwards. Then slide the slots of the rear support bracket under the seat frame. Once the slots of the rear support bracket are slid into place, tighten the bolts and studs. Then secure the mounting base to the rear support bracket using two X0 bolts and two X washers.(see FIG. ) Passenger Inner Seat Rail And olt Locations FIG. Gun Rack ase river Inner Seat olt Location
3 FIG.. Rest the gun rack, G00A on the previously installed base. Install two X0 bolts with two X washers into the rear two slots of the gun rack to secure it to the base. Install two more X0 bolts and two X washers in the two middle slots. (Leave these bolts loose for now to allow movement of the gun rack on the base). See FIG.. FIG. G00A IV. Weapon fitment. A. Remove the philips head screws that secure black plastic AS back to the gun rack. Remove the back from the gun rack for the rest of the gun lock adjustment process.. Place weapon in the gun rack and adjust lock and butt plate bracket to properly fit weapon. harging brackets and trigger guards should also be adjusted to ensure the weapon cannot be discharged. G0-0
4 V. Final installation. A. Wire electric gun locks per timer instructions. See page. Re-install the back onto the gunrack with the screws that were removed earlier.. Tighten all the bolts securely, now that all adjustments have been made to properly fit the weapon. VI. Lock Head Operating Instructions To release the weapon: A. Grasp the weapon, but do not pull it against the lid of the gun lock.. While depressing and holding the release button (momentary switch), push and then pull the weapon towards the lid of the gun lock to release it from the lock. Note: One handed operation is possible utilizing the optional second timer. The timer will unlock the lock for seconds following activation of the momentary switch. If the gun is not pulled out of the lock within seconds after activation of the momentary switch, the lock will automatically re-lock. Important: If lid of the lock does not release, press in on the lid to release tension and reactivate the release button (unless timer is still active). VII. Securing the Weapon: A. Push weapon firmly and completely into the lock mechanism and firmly close lid.. heck to insure that the lid is locked.. If the lid does not lock, re-seat the weapon firmly and completely into the lock assembly and again apply pressure to the lock lid to seat and re-lock it. Note: The G0 Series lock mechanism has a unique override. In the event of power failure, the lock can be opened using a standard handcuff key or other high security key. VIII. To open the lock with the manual override key: A. Fully insert the handcuff key into the hole provided in the lock head. Turn the key / turn to the left (counter-clockwise). Pull open the lid or pull on the weapon to open it. Important: Return the key to its original position or remove key completely to close and re-lock the lock.
5 IX. Installing Optional second timer (-Wire) Note: If for any reason the gun lock momentary switch remains activated, such as, the button is damaged, and/or shorted, the unit will time out in seconds and can not be operated again until the defective switch is repaired, thus saving the gun lock solenoid. o not connect directly to power for more than 0 seconds! X. Installation omplete REVISION HISTORY REV SHEET ESRIPTION AUTHOR ATE 0 ALL NEW RELEASE dustin // FARIATE PARTS LIST 0 0 ITEM 0 ITEM QTY PART NUMER ESRIPTION PARTS LIST G-00 RUER UTT PLATE PA QTY PART NUMER ESRIPTION G-00 UTT PLATE LAK NYLON G0 GUN LOK ASSEMLY G0H G00A GUN RAK, VERTIAL MOUNT SHOTGUN LOK G0-NPG G00 A.R. AS FOREGRIP GUNRAK LOK AKING PANEL GP G0-0 ALUMINUM MOUNTING UTT PLATE ASE * G0- G0-0 UTT PLATE REAR SUPPORT MOUNT RAKET, AJUSTALE X0 /-0 x /" HHMS, LAK X HARWARE / FLAT LIST WASHER, LAK ITEM X QTY PART NUMER /-0 X / ESRIPTION ARRIAGE OLT X X /-0 #0 WHIZ X / NUT PHILLIPS TRUSS H X X /-0 /-0 X / X FLT / H SHS, PH, LAK LAK G00 PUSH UTTON SWITH, MOMENTARY (NOT SHOWN) X /" FLAT WASHER, LAK G00 TIMER, -SEON ELAY (NOT SHOWN) 0 X0 /-0 X / HEX H AP SREW G0 AS GUN RAK AK (NOT SHOWN) G0 GUN RAK MOUNT ASE KIT * = QTY MAY VARY EPENING ON ONFIGURATION UNLESS OTHERWISE SPEIFIE : IMENSIONS ARE IN INHES TOL ON PLAE EIMALS:.00 TOL ON PLAE EIMAL.0 IMENSIONS ARE IN INHESTOL ON ANGLES ATE: RAWN Y: HEKE Y: APPROVE: ENGR : //0 USTIN Pro-gard Products, LL enterpoint r., Suite 00 Indianapolis, IN () -0
INSTALLATION GUIDE GVM5611 SELF SUPPORTING STAND FOR DODGE CHARGER. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIE GVM5 SELF SUPPORTING STAN FOR 0-0 OGE HARGER STRONG RELIALE SEURE 00.0.0 THESE OMPONENTS ARE REQUIRE TO INSTALL THE PRO-GAR GVM5 SELF SUPPORTING STAN AN TRI-LOK GUN RAK G5-0 MOUNT ASE
More informationinstallation Guide self supporting stand for chevrolet tahoe pro-gard.com Strong Reliable Secure
installation Guide GVM55 self supporting stand for 05 + chevrolet tahoe Strong Reliable Secure 00.0.0 PRT NUMER G55U-0 G55U-05 G55U-0 PRT NUMER X0 X G55U TRI-LOK SELF SUPPORTING SE SET MOUNTING RKET -
More informationINSTALLATION GUIDE GVM8116FT SELF SUPPORTING STAND FOR 2016 FORD F150 4-DOOR. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIE GVMFT SELF SUPPORTING STN FOR 0 FOR F0 -OOR STRONG RELILE SEURE THESE OMPONENTS RE REQUIRE TO INSTLL THE PRO-GR G0 SELF SUPPORTING STN N TRI-LOK GUN RK Tri-Lock Gun Rack GVPMXXXX GFT Self
More informationINSTALLATION GUIDE GTM5617 TRUNK MOUNTED GUN RACK DOGDE CHARGER. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE GTM5617 TRUNK MOUNTED GUN RACK 2015-2017 DOGDE CHARGER STRONG RELIABLE SECURE pro-gard.com 800.480.6680 THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD GTM003 GUN RACK GTM5617
More informationINSTALLATION GUIDE WSD47UINT13 WEAPON STORAGE DRAWER & ASBD47UINT13 ALUMINUM STORAGE DRAWER CURRENT FORD UTILITY INTERCEPTOR
INSTALLATION GUIDE WSD7UINT WEAPON STORAGE DRAWER & ASBD7UINT ALUMINUM STORAGE DRAWER 0 - CURRENT FORD UTILITY INTERCEPTOR STRONG RELIABLE SECURE 800.80.80 THESE COMPONENTS ARE REQUIRED TO INSTALL THE
More informationINSTALLATION GUIDE P1000T15A PRO-CELL CURRENT TAHOE. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIE P000T PRO-ELL 0 - URRENT THOE STRONG RELILE SEURE 00.0.660 THESE OMPONENTS RE REQUIRE TO INSTLL THE PRTITION WXXXT river & Passenger Window ars Pro-ell Kit Wing Kit P000T / age Partition
More informationINSTALLATION GUIDE CARGO BARRIER CURRENT FORD UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE CARGO BARRIER 0 - CURRENT FORD UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD BARRIER SYSTEM B00 BARRIER B7 HARDWARE/WING KIT I. Refer
More informationINSTALLATION GUIDE P1000T15AOSB CHEVY TAHOE. pro-gard.com RELEASED STRONG RELIABLE SECURE
INSTLLTION GUIDE P000T5OS 05-09 HEVY THOE STRONG RELILE SEURE RELESED 0.9.0 pro-gard.com 00.0.660 THESE OMPONENTS RE REQUIRED TO INSTLL THE PRTITION WXXX57T5 Driver & Passenger Window ars Pro-ell Kit Wing
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUTS, INSTALLATION INSTRUTIONS PRO TRAXX 4 OVAL TUE STEP AR APPLIATION: 2014+ hevrolet Silverado / GM Sierra 1500 Double / rew ab 2015+ hevrolet Silverado / GM Sierra 2500/3500 HD Double
More informationZ125 Front Fork Upgrade kits. Installation SOP
Z125 Front Fork Upgrade kits Installation SOP Tools a. Loctite243 or Loctite2701 (Thread Locker) b. Loctite7649 (Activator) c. 33mm Hex Socket d. 17mm Hex Socket e. Shaft Clamping Tool (12mm) f. Shaft
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationINSTALLATION GUIDE PRISONER TRANSPORT LIGHTING. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE PRISONER TRANSPORT LIGHTING STRONG RELIABLE SECURE pro-gard.com 800.480.6680 THESE COMPONENTS ARE REQUI TO INSTALL THE PRO-GARD PRISONER TRANSPORT LIGHTING 3" Round LED Lighthead QTY=
More informationINSTALLATION GUIDE P1000 PRO-CELL CURRENT FORD POLICE UTILITY INTERCEPTOR. pro-gard.com STRONG RELIABLE SECURE
INSTALLATION GUIDE P1000 PRO-CELL 2013 - CURRENT FORD POLICE UTILITY INTERCEPTOR STRONG RELIABLE SECURE THESE COMPONENTS ARE REQUIRED TO INSTALL THE PRO-GARD PARTITION SYSTEM WB4711-01D WB4711-01P 4K47UINTPRO
More informationNOTES: 1. CUSTOMER ASSEMBLY SHEETS 2-6.
ITEM PRT NO. ESRIPTION QTY. NOTE NO. 1 MT360714LS STEEL UNLE MT360714L 1 573.14 LS 2 MT360714LHK HRWRE KIT FOR MT360714L 1 119.53 LS 3 MT360714S MT360714L/S PIPE KIT 1 04.42 LS REVISIONS REV. ZONE ESRIPTION
More informationInstallation Guide Philips MP90 VHM Wall Mount Kit
Installation Guide Philips MP90 VHM Wall Mount Kit The purpose of this guide is to describe the procedures for installing the MP90 VHM Wall Mount Kit. Table of Contents Section 1.0: Mounting the VHM-Series
More information200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual. Model 642E Centrifuge
200 Shadylane Drive Philipsburg, PA 16866 Phone: (814) 342-6205 Fax: (814) 342-4510 www.druckerdiagnostics.com Service Manual Model 642E Centrifuge MODEL 642E SERVICE MANUAL REV: Original Issue 1 CONTENTS
More informationFord C4 and C6 Floor Mount Automatic Transmission Shifter Installation Instructions
Ford C4 and C6 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C4 and C6 Mount
More informationI-Sheet Number Rev.B 3-1/2 OVAL BULL BAR DODGE RAM 1500
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS FORD TRANSIT VAN (FULL SIZE)
INSTALLATION INSTRUCTIONS PARTS LIST: 1 32-inch Steel Running Board 1 8-1.25mm x 35mm Hex Bolt 1 96-inch Steel Running Board 13 8-1.25mm x 25mm Hex Bolt 5 Passenger Side/Driver Side Mounting Brackets 20
More informationInstallation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit
Installation Guide Philips MP2 IntelliVue M-Series Arm (12'' or 8'') Rail Mount Kit The purpose of this guide is to: 1. Describe mounting of MP2 equipment on Mounting Bracket (page 2). 2. Describe mounting
More informationDriver Side Support Bracket pictured in "no-tow hook" direction. Reverse direction for tow hook equipped vehicles
PARTS LIST: 1 Bull Bar 2 10-1.5mm x 35mm Hex Bolts 2 Tube Brackets (Bull Bar) passenger or driver side 2 10mm Lock Washers 2 Upper Frame Brackets (models w/o tow hooks only) 4 10mm x 27mm OD x 3mm Flat
More informationSINGLE-FRAME RELAY RACK ASSEMBLY INSTRUCTIONS
SINGLE-FRAME RELAY RAK ASSEMBLY INSTRUTIONS Single Frame_ass_instrux.indd 0/26/06 9:2:6 AM Single Rack Parts List ASSEMBLY HARWARE M8X5 Basic dimension eviation Shorter side eviation < > = Linear dim.
More informationChrysler 727, 904, 518 Floor Mount Automatic Transmission Shifter Installation Instructions
Chrysler 727, 904, 518 Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Button
More informationModels Affected: Certain 2015 & 2016 All American Front Engine and Vision Buses Equipped with Hydraulic Brakes ISSUE _ CORRECTIVE ACTION _
R E C A L L C A M P A I G N -- R 1 4 X R ---- Models Affected: Certain 2015 & 2016 All American Front Engine and Vision Buses Equipped with Hydraulic Brakes ISSUE _ CORRECTIVE ACTION -- -- _ The parking
More informationFord AOD-4R70W-AODE Cable Operated Shifter Installation Instructions
Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable
More informationCHEVY SILVERADO CREW CAB RX3 Includes models equipped with DEF tank
2007-2017 CHEVY SILVERADO 1500-3500 CREW CAB RX3 Includes models equipped with DEF tank HARDWARE INCLUDED RECOMMENDED TOOLS 1 Passenger Side Front Support Plate 13mm Wrench 1 8-1.25 x 40mm Hex Bolt 13mm
More informationL Light Bracket Crossbar Light Mount Bracket. Driver/left Support Bracket
PARTS LIST: Qty Description Qty Description 1 Light Bar 4 8-1.25mm x 35mm Hex Bolts 1 Crossbar Light Mount Bracket 6 8-1.25mm x 30mm Hex Bolts 2 Universal s 14 8mm x 24mm x 2mm STD Flat Washers 1 Driver/Left
More informationGM Floor Mount Automatic Transmission Shifter Installation Instructions
GM Mount Automatic Transmission Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com GM Mount Automatic Transmission
More informationEXHAUST. Crossover Manifold Replacement TX420 & & up. Crossover Manifold Removal
Crossover Manifold Replacement TX420 & 425 250000401 & up 4. Using an 8mm socket, remove the top bolt from the heat shield (Fig. 0245). Crossover Manifold Removal 1. Open and support the hood with the
More informationInstallation Guide. Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) Section 1.0: Mounting the M-Series Arm Parts Reference...
Installation Guide Philips MP90 M-Series Wall Mount Kit (12'' Pivot Arm) The purpose of this guide is to describe installation of the MP90 M-Series Wall Mount Kit. Table of Contents Section 1.0: Mounting
More information2014 Law Enforcement Products Chooseing the Right Gun Rack for Your Officers, Fleet, and Weapons
2014 Law Enforcement Products 2014 Chooseing the Right Gun Rack for Your Officers, Fleet, and Weapons Choosing the Right Gun Rack for your Weapon(s) Step 1: What type of vehicle will the gun rack be placed
More informationPOLY TIP-DOWN WINDSHIELD KIT
POLY TIP-DOWN WINDSHIELD KIT P/N 2883261 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please
More informationTESLA MODEL S REAR UNDER SPOILER & DIFFUSER SYSTEM
TESLA MODEL S Thank you for purchasing your Unplugged Performance Rear Under Spoiler & Diffuser System for the Tesla Model S! Please read this manual carefully prior to installation. REAR UNDER SPOILER
More information92-00 Civic/ Integra/ Del Sol/ Accord/ CRX. Front Kit Part No
LifeSTYLE 92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 90-97 Accord/ 92-95 CRX Front Kit Part No. 75440 www.airliftcompany.com MN-513 (08409) NPR 4778 Please read these instructions completely before proceeding
More informationINSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT
INSTALLATION INSTRUCTIONS FRONT PARTITION W/FILLER PANEL MOUNTING KIT P FRONT 1 with MFK 4 for 2008 2019 CHEVROLET PASSENGER VANS W/DUAL SIDE SWING OUT DOORS P FRONT 2 with MFK 8 for 2008 2019 CHEVROLET
More informationMC-CP12S SERIES & MC-CP14S SERIES
ITEM PRT NO. ESRIPTION QTY. NOTE NO. REV. EN MP4SHK HRWRE KIT FOR M-P/4S 4.47 LS 8000006976 MT36074... STEEL UNLE SEE TLE - 3 MP... PIPE UNEL SEE TLE - REVISIONS ESRIPTION Y TE INITIL RELESE 03/3/ M-PS
More informationGH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS
GH-BETTIS SERVICE INSTRUCTIONS DISASSEMBLY & REASSEMBLY FOR MODELS HD521-M4, HD721-M4 AND HD731-M4 DOUBLE ACTING SERIES PNEUMATIC ACTUATORS WITH HYDRAULIC CONTROL PACKAGE PART NUMBER: SE-023 REVISION:
More informationPowerglide Automatic Floor Mount Shifter Installation Instructions
Powerglide Automatic Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com Powerglide
More informationGun Racks. Tri-Lock Weapon Mounting System. Shown in a Chevrolet Tahoe
Gun Racks Tri-Lock Weapon Mounting System Shown in a Chevrolet Tahoe Tri-Lock Weapon Mounting System Pro-gard s Tri-Lock Weapon Mounting System easily accommodates your officer s weapon regardless of the
More informationFord AOD-4R70W-AODE Cable Operated Shifter Installation Instructions
Ford AOD-4R70W-AODE Cable Operated Shifter Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford AOD-4R70W-AODE Cable
More informationAutomatic Electronic Sport Mode Shifter Installation Instructions
Automatic Electronic Sport Mode Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Automatic Electronic Sport Mode
More informationINSTALLATION INSTRUCTIONS BULL BAR DODGE RAM 1500 PART # B-D1091;B-D2091
INSTALLATION INSTRUCTIONS PART # B-D1091;B-D2091 PARTS LIST: Qty Description Qty Description 1 Bull Bar 10 12mm Lock Washers 2 Upper Frame Brackets (for trucks without tow hooks only) 8 12-1.75mm Hex Nuts
More informationInstallation Guide Stack Mount Kit for Philips G5 and MP5/20/30/40/50/60/70 Monitor
Installation Guide Stack Mount Kit for Philips G5 and MP5/20/30/40/50/60/70 Monitor The purpose of this guide is to describe installation of the Stack Mount. Parts Reference The following parts and hardware
More informationInstallation Guide. Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit
Installation Guide Philips MP20/30/40/50 IntelliVue VHM Wall Mount Kit The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter. 2. Describe attachment of Mounting
More informationPARTS MANUAL. PS314SBI Gas and Electric Ovens. Models: for domestic and standard export ovens PS314SBI Middleby Marshall, Inc.
Parts Gas & Electric (AGA[CSA]/UL) P/N 38812 Rev. B V2 1/00 Gas and Electric Ovens Models: PARTS MANUAL for domestic and standard export ovens 2000 Middleby Marshall, Inc. is a registered trademark of
More informationTEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-FOR SPARTAN RUNNING BOARD FORD ECONOLINE 99-14
TEL:1-866-XANATOS INSTALLATION INSTRUCTIONS PART#: SR-FOR203796 SPARTAN RUNNING BOARD FORD ECONOLINE 99-14 PARTS LIST: 1 Driver/Left Side Spartan Running Board 2 10mm Lock Washers 1 Passenger/Right Side
More informationChrysler 45RFE Tailmount Automatic Transmission Shifter Installation Instructions
Chrysler 45RFE Tailmount Automatic Transmission Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Chrysler 45RFE Tailmount
More informationInstallation Guide. Xprezzon Roll Stand
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Xprezzon Roll Stand The purpose of this guide is to describe assembly of the Roll Stand and
More informationGPS Steering System Installation Manual
GPS Steering System Installation Manual Supported Vehicles Challenger Massey Ferguson AGCO MT-645C, MT-645D MF-8650 DT-205B MT-655C, MT-655D MF-8660 DT-225B MT-665C, MT-665D MF-8670 DT-250B MT-675C, MT-675D
More informationInstallation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue
Installation Guide VHM Wall Mount Kit for Philips MX600/700/800 and MP60/70 IntelliVue The purpose of this guide is to: 1. Describe attachment of Table Top Mount to Mounting Adapter (page 2). 2. Describe
More informationINSTALLATION GUIDE 4PK57SS15 SPACE SAVER PLUS PARTITION CURRENT TAHOE & 2016 SILVERADO. pro-gard.com STRONG RELIABLE SECURE
INSTLLTION GUIDE PK7SS SPE SVER PLUS PRTITION 0 - URRENT THOE & 0 SILVERDO STRONG RELILE SEURE 00.0.0 THESE OMPONENTS RE REQUIRED TO INSTLL THE PRTITION Space Saver Plus Partition Hardware Kit Wing Kit
More informationLOCKN LOAD FIRST TIME INSTALLATION
LOCKN LOAD TM TRACK MOUNTING KIT FORD RANGER PX / MAZDA BT-50 DUAL CAB 2011 + 2 BAR TRACK HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES
More informationINSTALLATION INSTRUCTIONS RDO 2503/2505 SLIDE DOOR OPERATOR VOLKSWAGEN EUROVAN KIT # 01138
INSTALLATION INSTRUCTIONS RDO 2503/2505 SLIDE DOOR OPERATOR VOLKSWAGEN EUROVAN KIT # 01138 # Be certain that these supplemental instructions are read and understood completely before installation is attempted.
More informationGPS AutoSteer System Installation Manual
GPS AutoSteer System Installation Manual Supported Vehicles Case IH Vehicles Case 2577 Combines Case 2588 Combines Accuguide Ready PN: 602-0233-01-A LEGAL DISCLAIMER Note: Read and follow ALL instructions
More informationInstallation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Folding L-Bracket with Display Mounting Extension and Keyboard Tray for M-Series or VHM Arm
More informationOPERATING INSTRUCTIONS FOR. Gold-Place TM. Manual Pick & Place with Dispenser System Model MPP-21
OPERATING INSTRUCTIONS FOR Gold-Place TM Manual Pick & Place with Dispenser System Model MPP-21 AUTOMATED PRODUCTION SYSTEMS, INC. 2840 Pine Road Huntingdon Valley PA 19006 Phone: (215) 938-1000 FAX: (215)
More informationEASYBIRD AUTO-FEED 6 - PACKER Part No (40912 with Oscillating Base)
EASYBIRD AUTO-FEED 6 - PACKER Part No. 40911 (40912 with Oscillating Base) Instruction Manual WARNING! THIS MACHINE CAN CAUSE SERIOUS INJURY OR DEATH. THOROUGHLY READ INSTRUCTIONS BEFORE INSTALLING OR
More informationInstallation Manual. AutoSteer. Gleaner Combine. AutoGuide 2 Steer Ready. Supported Models A66 A76 R66 R76 S67 S77 PN: A
Installation Manual AutoSteer Gleaner Combine AutoGuide 2 Steer Ready Supported Models A66 A76 R66 R76 S67 S77 PN: 602-0312-01-A LEGAL DISCLAIMER Note: Read and follow ALL Instructions in this manual carefully
More informationFord C6 Automatic Trans Mount Shifter Installation Instructions
Ford C6 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Ford C6 Automatic Trans Mount Installation
More informationCOMMANDER 3000 CLASSIC PANEL MOUNT REMOTE CONTROL
COMMANDER 3000 CLASSIC PANEL MOUNT REMOTE CONTROL 74428 11 Tle of Contents Pge Commner 3000 Clssi Remote Control Mintenne n Replement Prts.... 11-1 Disssemly............................. 11-2 Clening n
More informationE Series Enclosures Installation Instructions (UL /UL2416 E Series Equipment Cabinet/Rack)
E Series Enclosures Installation Instructions (UL60950-1/UL2416 E Series Equipment Cabinet/Rack) WeRackYourWorld.com 1-866-TRY-GLCC (879-4522) Instructions for the following Great Lakes Enclosures: GL720E-2432,
More informationChrysler 727, 904, and 518 Automatic Trans Mount Shifter Installation Instructions
Chrysler 727, 904, and 518 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Chrysler 727, 904, and
More informationLOADING ALIGNMENT TOOL GUIDE TOOL ASSEMBLY NOTE: 1 SCREWS SHOULD NOT PROTRUDE INTO INTERIOR.
NOTE: SREWS OUL NOT PROTRUE INTO INTERIOR. ESRIPTION 4 HKR PV TE HEK FOR LIGNMENT. TWO SURFES OUL E FLU. PROPRIETRY T STNFOR UNIVERSITY N/OR REIPIENT LL NOT PULI THE WITHIN INFORMTION WITHOUT SPEIFI PERMISSION
More informationREPLACEMENT PARTS MANUAL FOR AU 52 AUTO-GRINDERS S/N 101 TO 599
REPLACEMENT PARTS MANUAL FOR AU AUTO-GRINDERS S/N 0 TO AU (THAT WERE MANUFACTURED Y LASAR MFG. UNTILL ) AMERICAN MEAT EQUIPMENT CORP. HAD NO CONNECTION TO THE DESIGN, MANUFACTURING OR SALES OF THESE MACHINES
More informationInstallation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Manual for Philips SureSigns VS3/VS4/VM4/VM6/VM8/VSV VHM-25 Countertop Mount Install Time: 20-30
More information200 Shadylane Drive Philipsburg, PA Phone: (814) Fax: (814) Service Manual
200 Shadylane Drive Philipsburg, PA 16866 Phone: (814) 342-6205 Fax: (814) 342-4510 www.druckerdiagnostics.com Service Manual Model 755VES Centrifuge MODEL 755VES SERVICE MANUAL REV: A 1 CONTENTS 1 PREFACE...
More informationSelf-Deploying Rail Kit OEM INSTALLATION MANUAL
Self-Deploying Rail Kit OEM INSTLLTION MNUL TLE OF ONTENTS Introduction 2 Safety Information 2 Resources Required 3 Prior to Installation 3 Installation 3 Doorjamb 3 Setting the Doorjamb 3 inch Latch 4
More informationGCX Mounting Assembly Installation Guide. Philips MP90 (M8010A) Mounting Kit for Drager Zeus
GCX Mounting Assembly Installation Guide Philips MP90 (M8010A) Mounting Kit for Drager Zeus The purpose of this guide is to: 1. Describe attachment of Down Post to Arm. 2. Describe attachment of Arm to
More informationBike Bollard R-7904 (RSA)
ike ollard R-0 (RS) General escription: The R-0 ike ollard offers versatile design and functionality. ike-locking arms are bolted internally to applications. R-0 ike ollards are made from carbon steel
More informationSAFETY THIS PRODUCT IS FOR OFFROAD USE ONLY. ALL LIABILITY FOR INSTALLATION AND USE RESTS WITH THE OWNER.
SAFETY Your safety and the safety of others is very important. In order to help you make informed decisions about safety, we have provided installation instructions and other information. These instructions
More informationEmbedded Rack Slide-out System
Embedded Rack Slide-out System SERVICE MANUAL Rev: 02.16.2017 Page 1 Electric Embedded Rack Slide-out System TABLE OF CONTENTS Safety Information 3 Product Information 3 Operation 4 Extending Slide-Out
More informationINSTALLATION INSTRUCTIONS PART NUMBER: DC (GUN METAL GRAY)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-8033DC (GUN METAL GRAY) 2014-15 Chevrolet Silverado 1500 5.3L/6.2L V8 2014-15 GMC Sierra 1500 5.3L/6.2L V8 2015
More information1. Single-speed bicycle (SSB) lower fork legs... Page 3 2. Multi-speed bicycle (MSB) lower fork legs... Page 4
TM owner s instruction manual the ULTIMATE SURFBOARD RACK I. Messages & Warnings...Page 2 II. FORK BASE UNIT COMPONENTS...Page 2 III. SELECTING PROPER LEG TYPE...Page 2 IV. LEG LENGTH ADJUSTMENT & FORK
More informationB C PART PART # DESCRIPTION
PRT PRT # ESRIPTION INLUE F6005 XLE,VULT,FRONT,,SI LVER F60056 ENP SET,VULT,F,5x00, F60059 ENP SET,VULT,F,5x00,TORQUE P, F60057 ENP SET,VULT,F,0X0 E,E F60058 ENP SET,VULT,F,9X00,QR F,F F60060 ERI NG,6805
More informationTH200 & TH200-4R Automatic Trans Mount Shifter Installation Instructions
TH200 & TH200-4R Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com
More informationJEEP Wrangler V6-3.8L
63-1574 JEEP 2007-11 Wrangler V6-3.8L NOTE: This kit was not designed to fit vehicles with a body lift. AQ AR AR AP AN A E AO AJ AI AM AH AL AK K AF A AE A A A F AA Z J I H M N M P Q AS O V W R Y S R X
More informationINSTALLATION MANUAL. Thunderstone Manufacturing LLC 3400 West O Street Lincoln, NE (Fax)
INSTALLATION MANUAL August 7 th 2018 43 /48 /50 2011 and Older Timpte STD/Split 36 Style Hopper Trailers with Roller Bearing Doors Kit #101533 for 96w & Kit #101534 for 102w Thunderstone Manufacturing
More informationTH400 Automatic Trans Mount Shifter Installation Instructions
TH400 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com TH400 Automatic Trans Mount Installation
More informationTH350 Automatic Trans Mount Shifter Installation Instructions
TH350 Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 (865) 966-2269 FAX (865) 671-1999 tech@lokar.com www.lokar.com TH350 Automatic
More informationLOCKN LOAD MOUNTING KIT
LOCKN LOAD MOUNTING KIT TM VOLKSWAGEN AMAROK 2 BAR FIXED POINT HEAVY DUTY ROOF RACK SYSTEM MAX VEHICLE ROOF LOAD RATING: 100KG TOTAL LOAD EQUALS WEIGHT OF ROOF RACKS + ACCESSORIES + CARGO FIRST TIME INSTALLATION
More informationASSEMBLY MANUAL. Manual en Español Latino Americano:
ASSEMLY MANUAL Manual en Español Latino Americano: www.support.nautilus.com Table of Contents / Registration Congratulations on your commitment to fitness and your purchase of the owflex Xtreme 2 SE home
More informationInstallation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket and 10lbs/4.
3875 Cypress Drive Petaluma, CA 94954 800.228.2555 707.773.1100 Fax 707.773.1180 www.gcx.com Installation Guide Roll Stand Kit 2''/5.1cm Diameter Post with Tilt/Swivel Mounting Plate, Handle, Utility Basket
More informationParts List. Item Qty. Part # Description Item Qty. Description Torque
Installation Instructions BR20 Rear Bumper Replacement Part Number 28171T Chevrolet Silverado 1500 2/4WD Parts List Item Qty. Part # Description Item Qty. Description Torque 1 1 28171T0AA Bumper Replacement
More informationPOLARIS 4500 HD WINCH KIT
POLARIS 4500 HD WINCH KIT P/N 2883860 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More informationInstallation Guide VHM Arm Kit for Philips Heartstart MRx and Heartstart XL+
Installation Guide VHM Arm Kit for Philips Heartstart MRx and Heartstart XL+ The purpose of this guide is to: 1. Describe installation of Arm in channel (page 2). 2. Describe mounting of defibrillator
More information2 CYLINDER MOBILE CART ASSEMBLY INSTRUCTIONS
Parker Hannifin Corporation Precision Fluidics Division Porter Instrument 245 Township Line Road Hatfield, PA 9440 Office 25-723-4000/Fax 25-723-506 www.porterinstrument.com 2 CYLINDER MOBILE CART ASSEMBLY
More informationINSTALLATION INSTRUCTIONS Product Revision Form Rev. C INST-439 CRADLE, DELL E-6510/6500
7160-0202 Cradle is designed to be used with a Dell E-Port or E-Port Plus Port Replicator. The cradle is assembled for used with Dell E-6510. By removing 2 Side Spacers the Cradle can also be used with
More informationPROCEDURE: Example of GM factory body mount bolt
IMPORTANT ALERT: GM uses a very strong thread-locking compound on all body bolts. Use of an air assisted impact ratchet can cause damage to the threads on factory body mount bolts and the internal nut
More information4L80E Automatic Trans Mount Shifter Installation Instructions
4L80E Automatic Trans Mount Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com 4L80E Automatic Trans Mount Installation
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS 2011 Dodge Charger Road Defender 5000 Series Push Bumper Part Number 5076 Do not attempt to install this product on any vehicle other than the one it is designed for and listed
More information6 Inch Oval Step Board
` 6 Inch Oval Step Board Part No. G9001B-1 Fits: 1999-2013 Chevrolet Silverado / GMC Sierra 1500/2500/3500 HD ( All Cabs ) REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 35-45 min Cutting Required
More informationTOYOTA SOLARA EC REARVIEW MIRROR Section I - Installation Preparation
Section I - Installation Preparation Part Number: PT374-33020 Section I - Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 AD Mirror Assembly w/compass 2 1 Hardware Bag 3 1 Installation
More information92-00 Civic/ Integra/ Del Sol/ Accord/ CRX
92-00 Civic/ 94-01 Integra/ 93-97 Del Sol/ 90-97 Accord/ 92-95 CRX Front Kit Part No. 75440 www.airliftperformance.com Please read these instructions completely before proceeding with installation MN-513
More informationINSTALLATION & OWNER S MANUAL
Rev. E p. of 3 INSTALLATION & OWNER S MANUAL V446 Front Cab Kit and V446 Rear Cab Kit for RTV 40 INSTALLATION & OWNER S MANUAL The contents of this envelope are the property of the owner. Be sure to leave
More informationInstallation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA
Installation Instructions 1812 Folder Disk Clutch Retrofit Kit Martin Yale #WRA1812510 Background: Early production Martin Yale Model 1812 Folders were originally equipped with a spring-clutch type feed
More informationRunning Board. Part No. RBV05B. PARTS LIST: Qty Part Description Qty Part Description
` Running Board Part No. RBV05B Fits: 2014 - Current Dodge Ram Promaster 136 /159 wheel base REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. 60-180 min Cutting May be Required Drilling Required
More informationDOCUMENT # LINE NO. NUMBER
DOUMENT NUMER NOTE: ONE KIT (ATALOG #: MTR-) ENALES UP TO () LEADS TO E ONNETED TO ONE TERMINAL. - SSD/OVP us Decoupler Extra Leads Plated 9 Washer Flat /" 9 Washer Split Lock /" 9 Nut Hex /-8 Screw Hex
More informationINSTALLATION INSTRUCTIONS RATTLER STEEL RUNNING BOARDS DODGE RAM 1500 QUAD CAB
INSTALLATION INSTRUCTIONS PARTS LIST: 2 Steel Running Boards 5 12mm Lock Washers 1 Driver/Left Mounting Bracket 5 12mm Hex Nuts 1 Driver/Left Center Mounting Bracket 6 10-1.5mm x 35mm Hex Bolts 2 Driver/Left
More informationHYDRAULIC LANDING GEAR REPLACEMENT
Purpose This kit outlines the procedure to replace existing square hydraulic landing gear jacks, including square and round hydraulic, pin-less jacks. Square landing gear is no longer available. Required
More informationService and Repair Note:
Service and Repair Note: Ford does not provide camshaft gear timing marks, or information to perform timing belt service without the special tools shown in this procedure. Timing Drive Components - Timing
More information