01 20 CRUISE CONTROL SYSTEM

Size: px

Start display at page:

Download "01 20 CRUISE CONTROL SYSTEM"

Russell Abner Wood
5 years ago
Views:

1 01 20 CRUISE CONTROL SYSTEM LOCATION INDEX CRUISE CONTROL MODULE REMOVAL/INSTALLATION CRUISE CONTROL MODULE INSPECTION Terminal Voltage List (Reference) CRUISE ACTUATOR REMOVAL/INSTALLATION End of Toc LOCATION INDEX CRUISE ACTUATOR INSPECTION ACTUATOR CABLE REMOVAL ACTUATOR CABLE INSTALLATION CRUISE CONTROL SWITCH REMOVAL/INSTALLATION CRUISE CONTROL SWITCH INSPECTION A3U W Z3U0120W Transmission range (TR) (ATX) (See TRANSAXLE RANGE (TR) SWITCH (See TRANSAXLE RANGE (TR) SWITCH REMOVAL/INSTALLATION) (See TRANSAXLE RANGE (TR) SWITCH ADJUSTMENT) 2 Clutch (MTX) (See 01 40B 42 CLUTCH SWITCH INSPECTION [FS]) (See 01 40A 41 CLUTCH SWITCH INSPECTION [ZM]) 3 Brake SWITCH 4 module (See CRUISE CONTROL MODULE REMOVAL/INSTALLATION) (See CRUISE CONTROL MODULE 5 (See CRUISE ACTUATOR REMOVAL/ INSTALLATION) (See CRUISE ACTUATOR 6 Actuator cable (See ACTUATOR CABLE REMOVAL) (See ACTUATOR CABLE INSTALLATION) 7 (See CRUISE CONTROL SWITCH REMOVAL/INSTALLATION) (See CRUISE CONTROL SWITCH 8 Vacuum hose

2 CRUISE CONTROL MODULE REMOVAL/INSTALLATION A3U W01 2. Remove the passenger-side front side trim. (See FRONT SIDE TRIM REMOVAL/INSTALLATION.) 3. Remove in the order indicated in the table. 1 Connector 2 Bolt 3 module 4. Install in the reverse order of removal. CRUISE CONTROL MODULE INSPECTION A3U W02 1. Remove the passenger-side front side trim. (See FRONT SIDE TRIM REMOVAL/INSTALLATION.) 2. Remove the cruise module without disconnecting the connector. 3. Measure the voltage at the cruise module terminals as indicated below. 4. Disconnect the cruise module connector before inspecting for continuity at terminal P. If not as specified, inspect the parts listed under Action. If the parts and wiring harnesses are okay but the system still does not work properly, replace the cruise module. Terminal Voltage List (Reference) X3U120WA0 Y3U120WA0 Terminal A B C D Signal set indicator light output Connected to (Vent 1) (Vacuum) (Vent 2) set indicator light at ON at ON at ON Test condition main at ON Voltage (V) /Continuity B+ Other main at ON B+ Other main at ON B+ Other Action Inspect brake SWITCH Inspect cruise (See CRUISE ACTUATOR Inspect brake SWITCH Inspect cruise (See CRUISE ACTUATOR Inspect brake SWITCH Inspect cruise (See CRUISE ACTUATOR at ON B+ Inspect METER 10 A fuse Inspect instrument cluster at LOCK or ACC (See INSTRUMENT CLUSTER

3 Terminal at ON B+ METER Inspect METER 10 A fuse E IG1 10 A fuse at LOCK or ACC F G O/D off PCM H I J K L M N O P power supply Test ATX MTX Signal Selecto r lever Clutch on/off Brake on/off Brake on/off Vehicle speed main input module ground Connected to Brake Data link connector Transaxle range Clutch Brake Brake Vehicle speed sensor GND at ON B+ Inspect PCM (See 01 40A 7 PCM at LOCK or ACC at ON at ON and cruise main at ON at ON and cruise main at ON main at ON main at OFF B+ INSPECTION [ZM]) (See 01 40B 7 PCM INSPECTION [FS]) Selector lever at N or P range Other B+ Depress clutch pedal Other B+ Inspect transaxle range (See TRANSAXLE RANGE (TR) SWITCH Inspect clutch (See 01 40A 41 CLUTCH SWITCH INSPECTION [ZM]) (See 01 40B 42 CLUTCH SWITCH INSPECTION [FS]) Depress brake pedal B+ Inspect brake Other SWITCH at ON and cruise main at ON at ON and cruise main at ON at ON and cruise main at ON at ON Test condition SET/COAST hold at on Approx. 1.5 RESUME/ACCEL hold at on Approx. 0.5 CANCEL hold at on Approx. 3 Other Approx. 5 Depress brake pedal Other B+ Rear tires rotating Other main at ON Inspect cruise (See CRUISE CONTROL SWITCH Inspect brake SWITCH Alternates below 1.0 and 5 or 5 Other B+ Constant: inspect for continuity to ground Voltage (V) /Continuity Action Inspect METER 10 A fuse Inspect instrument cluster (See INSTRUMENT CLUSTER Inspect cruise (See CRUISE CONTROL SWITCH Yes

4 CRUISE ACTUATOR REMOVAL/INSTALLATION 2. Remove in the order indicated in the table. 3. Install in the reverse order of removal. A3U W01 A3U0120W connector 2 Actuator cable (See ACTUATOR CABLE REMOVAL) (See ACTUATOR CABLE INSTALLATION) 3 Vacuum hose 4 Nut 5 Screw 6 Bracket 7 8 Nut 9 Bracket CRUISE ACTUATOR INSPECTION 2. Disconnect the cruise connector. 3. Measure the resistance between the cruise terminals using an ohmmeter. A3U W02 Z3U0120W Disconnect the cable from the accelerator pedal. 5. Allow the engine to idle. 6. Connect B+ and a ground to the terminals as shown and confirm the operation of the cable. If not as specified, replace the cruise. Step Terminal connection Operation of A B C D cable 1 Ground B+ Ground Ground Pull 2 Ground B+ Ground Hold 3 B+ Ground Extend 4 Released Y3U120WA

5 ACTUATOR CABLE REMOVAL 1. Loosen the nut, and remove the cable. A3U W Press the tabs of the bush, and remove it from the accelerator pedal. Z3U0120W Press the tabs of the grommet, and remove it from the dash lower panel. 4. Push the cable through the dash lower panel to remove it. Y3U120WA5 ACTUATOR CABLE INSTALLATION 1. Install the grommet to the dash lower panel. Y3U120WA6 A3U W02 Y3U120WA

6 2. Install the cable to the accelerator pedal. CRUISE CONTROL SYSTEM 3. Slide the lock lever in the direction shown by the arrow to unlock the adjuster. Y3U120WA5 4. Turn the ratchet ring to release lock in the direction shown by the arrow. YMU120WAA 5. Insert the grommet into the bracket. YMU120WAB 6. To adjust the free play, push or pull the cable directly behind the spring two times. Z3U0120W004 YMU120WAJ

7 7. Turn the ratchet ring in the direction shown by the arrow to lock it. CRUISE CONTROL SYSTEM Slide the lock lever in the direction shown by the arrow to lock the adjuster. YMU120WAC CRUISE CONTROL SWITCH REMOVAL/INSTALLATION 2. Remove the driver-side air bag module. (See DRIVER-SIDE AIR BAG MODULE REMOVAL/ INSTALLATION.) 3. Disconnect the cruise connector. 4. Remove in the order indicated in the table. 1 Screw (4SD) 2 Horn button contact (4SD) 3 Screw 4 5. Install in the reverse order of removal. YMU120WAD A3U W01 A3U0120W

8 CRUISE CONTROL SWITCH INSPECTION CRUISE CONTROL SYSTEM 2. Remove the driver-side air bag module. (See DRIVER-SIDE AIR BAG MODULE REMOVAL/ INSTALLATION.) 3. Disconnect the cruise connector. 4. Measure the resistance and inspect for continuity between the cruise terminals using an ohmmeter. A3U W02 Y3U120WA4 Z3U0120W

02 14 REAR SUSPENSION

02 14 REAR SUSPENSION REAR SUSPENSION REAR SUSPENSION LOCATION INDEX................ 02 14 1 REAR SHOCK ABSORBER AND SPRING REMOVAL/INSTALLATION.. 02 14 2 Coil Spring Installation Note......... 02 14 3