MAIN CONTROL VALVE BODY. Removal 1. Disconnect the battery cables. 2. Remove the battery and tray.
|
|
- Felicity Alexander
- 5 years ago
- Views:
Transcription
1 1 of 17 MAIN CONTROL VALVE BODY Removal 1. Disconnect the battery cables. 2. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) / intake air temperature (IAT) sensor. 4. Remove the intake tube and air cleaner cover.
2 2 of Disconnect the transaxle wiring harness electrical connector, and TR sensor connector. 6. Disconnect the shift cable.
3 3 of Remove the shift cable and bracket, and position out of the way. 8. Remove the vent tube hose. 9. Raise and support the vehicle. 10. Remove the LH front wheel.
4 4 of Remove the splash shield. Note: ^ Remove the bolts in the indicated sequence. 12. Remove the main control cover.
5 5 of Remove the main control cover gasket. Note: ^ Remove the bolts in the indicated sequence. 14. Remove the main control valve body bolts.
6 6 of 17 Note: ^ Do not damage the manual valve. 15. Lift the main control valve body while disconnecting the manual valve link. 16. Depress the retaining tabs and push the solenoid valve body electrical connector down through the transaxle case.
7 7 of Make sure the manual valve control lever does not fall out of the main control valve body while removing from the vehicle. Installation 1. Install the manual control valve.
8 8 of 17 Note: ^ Inspect the solenoid valve body harness connector O-ring seal for damage. Install a new O-ring seal, if damaged, before installing the connector into the case. 2. Push the solenoid valve body harness connector into the case. 3. Connect the manual valve link to the main control valve body.
9 9 of Install the main control valve body and tighten the bolts in sequence as indicated. 5. Loosen the nut on the ball stud for the manual valve detent lever actuating rod assembly.
10 10 of Remove the manual control lever outer assembly bolt. 7. Using the special tool and pin, align the shifter shaft.
11 11 of Move the manual valve detent lever assembly to the "D" position. 9. Tighten the nut on the ball and remove the special tool. 10. Tighten the detent nut. Rotate back to the "D" position and check the adjustment.
12 12 of Using the special tool and pin, align the shifter shaft. 12. Install the manual control lever.
13 13 of Install and rotate the manual valve detent lever assembly to the neutral position. 1. Low 1 2. Low 2 3. Drive 4. Neutral 5. Reverse 6. Park 14. Install a new gasket on the main control cover.
14 14 of Install the main control cover, and tighten the bolts in sequence as shown. 16. Install the splash shield. 17. Install the LH front wheel. 18. Lower the vehicle.
15 15 of Install the shift cable and bracket. 20. Connect the shift cable.
16 16 of 17 Note: ^ Before installing the vent tube hose, clean out any obstructions in the hose using low air pressure. 21. Install the vent tube hose, and clamp. 22. Connect the transaxle harness connector, and the TR sensor connector.
17 17 of Install the intake tube and air cleaner cover. 24. Connect the breather tube and mass air flow (MAF) / intake air temperature (IAT) sensor. Note: ^ Before installing the battery tray check the vent tube hose for any obstructions, kinks, or incorrect routing position. 25. Install the battery tray and battery. 26. Connect the battery cables. 27. Check the transaxle fluid, add fluid as necessary using MERCON - Automatic Transaxle Fluid (ATF). 28. Start the engine and move the transaxle range selector lever through all gear positions. Refill as necessary ALLDATA, LLC. All Rights Reserved. (Version )
Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor.
1 of 19 10/1/2011 11:11 AM oval 1. 2. Disconnect the battery cables. Remove the battery and tray. 3. Disconnect the breather tube and mass air flow (MAF) /intake air temperature (IAT) sensor. 4. Remove
More informationIN-VEHICLE REPAIR. Main Control Valve Body. Removal. 6. Disconnect the transaxle wiring harness electrical connector and TR sensor connector.
307-01-1 Automatic Transaxle/Transmission 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Material Item Thread Sealant with PTFE TA-24 Motorcraft MERCON Multi-Purpose (ATF) Transmission Fluid XT-2-QDX
More information1998 Contour/Mystique Workshop Manual
SECTION 30-01: Automatic Transmission/Transaxle 1998 Contour/Mystique Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 09/14/2001 Main Controls Special Tool(s) Aligner, Selector Shaft 30-S290
More information1 of 14 11/19/ :45 AM
1 of 14 11/19/2016 11:45 AM 6F35 Digital Transmission Range (TR) Sensor Removal All vehicles 1. With the vehicle in NEUTRAL, position it on a hoist. 3.0L engine 2. Remove the Air Cleaner (ACL) outlet pipe.
More informationIN-VEHICLE REPAIR. Output Shaft Speed (OSS) Sensor. Removal
307-01-1 Automatic Transaxle/Transmission 6F50 307-01-1 IN-VEHICLE REPAIR Output Shaft Speed (OSS) Sensor Material Item MERCON V Automatic Transmission Fluid XT-5-QM (or XT-5-QMC) (US); CXT-5-LM12 (Canada)
More information9/20/2017 Automatic Transaxle/Transmission External Controls - Selector Lever Cable - Removal and Installation 2008 Ford Edge MotoLogic
2008 Edge SECTION 307-05: Automatic Transaxle/Transmission External Controls REMOVAL AND INSTALLATION 2008 Edge/MKX Workshop Manual Procedure revision date: 06/17/2009 Report a problem with this article
More informationPage 1 of 6 Section 07-01A: Transaxle, Automatic CD4E 1996 Probe Workshop Manual REMOVAL Procedure revision date: 06/14/2000 Transaxle Item Part Number Description 1 10655 Battery 2 10732 Battery Tray
More information2005 Honda ACCORD. Submodel: EX Engine Type: V6 Liters: 3.0 Fuel Delivery: FI Fuel: GAS. Automatic Transmission Installation. Special Tools Required
2005 Honda ACCORD Submodel: EX Engine Type: V6 Liters: 3.0 Fuel Delivery: FI Fuel: GAS Automatic Transmission Installation Special Tools Required Engine support hanger, A and Reds AAR-T-12566 Engine hanger
More informationALLDATA Online Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Intake Manifold Replacement (Upper)
ALLDATA Online - 2001 Chevy Truck S10/T10 Blazer 2WD V6-4.3L VIN W - Intake... Page 1 of 21 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component
More informationAutomatic Transmission 5R44E and 5R55E
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 IN-VEHICLE REPAIR Main Control Valve Body Special Tool(s) Aligner, Valve Body 307-333 (T95L-70010-B) Aligner, Valve Body 307-334 (T95L-70010-C)
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Cylinder Head Assembly» Valve Cover» Service and Repair» Procedures» LH Valve Cover LH Removal 1. Disconnect the battery ground cable. 2. Remove the air cleaner
More information2002 F-150 Workshop Manual
Page 1 of 8 SECTION 307-01B: Automatic Transmission 4R70W 2002 F-150 Workshop Manual REMOVAL Procedure revision date: 04/02/2003 Transmission Special Tool(s) Retainer, Torque Converter 307-346 (T97T-7902-A)
More information1 of 1 7/1/17, 2:02 PM. Air Cleaner Assembly Replacement ALLDATA, LLC. All Rights Reserved. (Version )
Air Cleaner Housing Service and Repair, Removal and Replacement: Ai... http://repair.alldata.com/alldata/article/display.action?componentid=367... 1 of 1 7/1/17, 2:02 PM Air Cleaner Assembly Replacement
More informationTiming Belt: Service and Repair Installation
1998 Mercury Mystique L4-122 2.0L DOHC VIN 3 SFI Copyright 2008, ALLDATA 9.50 Page 1 Timing Belt: Service and Repair Installation NOTE:Ford does not provide camshaft gear timing marks, or information to
More information2004 Honda ELEMENT. Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS. Engine Installation. Special Tools Required
2004 Honda ELEMENT Submodel: Engine Type: L4 Liters: 2.4 Fuel Delivery: FI Fuel: GAS Engine Installation Special Tools Required Engine hanger/adapter VSB02C000015 Engine support hanger, A & Reds AAR-T-12566
More informationAssembly. NOTE: Before beginning assembly, perform/inspect the following:
Page 1 of 31 Home Account Contact ALLDATA Log Out Help DAN GRIMWOOD DAN GRIMWOOD00002 Select Vehicle New TSBs Technician's Reference Component Search: OK 1997 Ford Truck F 150 2WD Pickup V6-4.2L VIN 2
More informationOil pan, oil strainer and valve body, removing and installing
Page 1 of 44 38-1 Oil pan, oil strainer and valve body, removing and installing WARNING! Do not run engine with the oil pan removed or without ATF filling and do not tow vehicle. Notes: Always replace
More information10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L
2005 Ford E 250 : Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L Intake Manifold 5.4L Listen SECTION 303 01A: Engine 4.6L and 5.4L 2005 E Series Workshop Manual IN
More information3/19/2017 9:49 AM. Transmission Replacement. Tools Required ^ J B Cooler Quick Connect Tool ^ J Transmission Jack Adapter
1 of 16 Transmission Replacement Tools Required ^ J 41623-B Cooler Quick Connect Tool ^ J 41160 Transmission Jack Adapter Removal Procedure 1. Remove the upper filler panel. 2. Remove the upper and lower
More informationIntake Manifold Replacement
Page 1 of 14 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer (VIN S/T) Service Manual Engine Engine Mechanical - 4.8L, 5.3L, and 6.0L Repair Instructions - On Vehicle Document ID:
More informationIntake Manifold Removal and Installation
2004 Element Intake Manifold Removal and Installation Exploded View Removal Report a problem with this article 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum
More information2003 ACCORD - Intake Manifold Removal and Installation
2003 ACCORD - Intake Manifold Removal and Installation Exploded View '06-07 Models Removal ('03-05 Models) 1. Disconnect the intake air temperature (IAT) sensor connector (A). 2. Remove the vacuum hose
More informationSECTION Automatic Transaxle/Transmission 6R80
307-01-i Automatic Transaxle/Transmission 6R80 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 6R80 CONTENTS PAGE IN-VEHICLE REPAIR Main Control... 307-01-2 307-01-2 Automatic Transaxle/Transmission
More informationFord 6.0L. Part #: Part #: BD GASKET PART# will be needed for this installation.
1 BD EGR COOLER 2003-2007 Ford 6.0L Part #: 1090201 Part #: 1090202 PLEASE READ ALL INSTRUCTIONS BEFORE INSTALLATION BD GASKET PART# 1090002 will be needed for this installation. 2 K I T C O N T E N T
More informationPage 1 of 7 Section 07-01A: Transmission, Automatic, E4OD IN-VEHICLE SERVICE 1993 Bronco/Econoline/F-Series Workshop Manual Valve Bodies and Intermediate Band Servo NOTE: If a transmission has been disassembled
More informationTIMING BELT REPLACEMENT. Tools Required. J A (KM-421-A) Timing Belt Adjuster J Angle Meter KM-470-B Angular Torque Gage
Page 1 of 20 TIMING BELT REPLACEMENT Tools Required J 42492-A (KM-421-A) Timing Belt Adjuster J 45059 Angle Meter KM-470-B Angular Torque Gage Removal Procedure Fig. 37: View Of Throttle Cable CAUTION:
More information2000 Chevrolet Blazer
HEATER CORE Removal Procedure 1. Remove the heater/vent module. Refer to HEATER/VENT MODULE. 2. Remove the heater core access cover screws. Fig. 14: Identifying Heater Core Access Cover & Screws 3. Remove
More information1 of 12 10/5/2015 8:11 AM
1 of 12 10/5/2015 8:11 AM REMOVAL 1. Perform the fuel pressure release procedure See: Fuel Pressure Release > Procedures > Fuel System Pressure Release Procedure. 2. Recover the refrigerant from the refrigerant
More information2002 Escape Workshop Manual
SECTION 303-01A: Engine 2.0L Zetec 2002 Escape Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/25/2004 Timing Belt Special Tool(s) Crankshaft TDC Timing Peg 303-574 (T97P-6000-A) Camshaft
More informationENGINE ASSEMBLY. COMPONENTS (Part 1)
1 of 32 ENGINE ASSEMBLY COMPONENTS (Part 1) 2 of 32 COMPONENTS (Part 2) 3 of 32 COMPONENTS (Part 3) 4 of 32 COMPONENTS (Part 4) 5 of 32 COMPONENTS (Part 5) 6 of 32 COMPONENTS (Part 6) 7 of 32 COMPONENTS
More information2003 Saturn Vue. SATURN 3.0L V6 DOHC - L-Series After VIN & Vue
TIMING BELT Removal 1. Disconnect negative battery cable. Remove air cleaner assembly. 2. Raise and support vehicle. Remove right front wheel. Remove lower front splash shield. 3. Lower vehicle. Loosen,
More informationLower Intake Manifold Replacement
Lower Intake Manifold Replacement Removal Procedure 1. Turn OFF all the lamps and the accessories. 2. Ensure the ignition switch is in the OFF position. 3. Disconnect the negative battery cable from the
More information1997 Volkswagen Jetta GT AUTOMATIC TRANSMISSIONS' 'Servicing - Volkswagen AUTOMATIC TRANSMISSIONS. Servicing - Volkswagen
1997-98 AUTOMATIC TRANSMISSIONS Servicing - Volkswagen APPLICATION TRANSAXLE APPLICATION Application Transaxle Model 1997 Golf, GTI, Jetta & Passat 01M 1998 Jetta, Golf, GTI 01M LUBRICATION CHECKING FLUID
More informationDisconnect negative battery cable and remove coolant bottle cap.
1 of 16 3/25/2012 10:18 AM ools Required SA9105E 3-Bar Engine Support Fixture SA9412G Constant Force Clamp Pliers SA9127E Gage Bar Set Powertrain Assembly Removal Caution: Do not allow smoking or the use
More information2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head
Cylinder Head http://repair.alldata.com/alldata/article/display.action?componentid=65&itypeid=401&nonstandardid=2762152&vehicleid=47645&miles=&printfriendl 1/17 RH Splash Shield Accessory Drive Belt, Thermostat
More informationTransmission Diesel Engines
Page 1 of 17 SECTION 307-01B: Automatic Transaxle/Transmission TorqShift 6 2011 F-250, 350, 450, 550 Super Duty Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 11/12/2010 Transmission
More information2002 Chevrolet Blazer
The blower motor will operate in any switch position, as long as the ignition switch is in the RUN position and the mode switch is in any position other than OFF. When the ignition switch is on, power
More informationINHIBITOR SWITCH AT-50. 5) Disconnect the inhibitor switch connector.
INHIBITOR SWITCH B: ADJUSTMENT 1) Shift the select lever to N range. 2) Loosen the three inhibitor switch securing bolts. 3) Insert the ST as vertical as possible into the holes in inhibitor switch lever
More information2014+ Ram 3.0 EcoDiesel EGR Delete
2014+ Ram 3.0 EcoDiesel EGR Delete Installation Guide WARNING: This product is for competition use only in a sanctioned racing event. NOT FOR USE ON VEHICLES USED OR REGISTERED FOR USE ON A PUBLIC ROAD
More informationIntake Manifold Removal
PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE INSTRUCTIONS Parts included: -GT350 Intake manifold M-944-M5 -GT350 Air bucket w/filter.
More informationTRANSMISSION SERVICING - A/T Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site -
TRANSMISSION SERVICING - A/T Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru ARTICLE BEGINNING 1997-98 TRANSMISSION SERVICING Automatic Transmission
More information2013 Kia Optima L4-2.0L Turbo
1 of 13 5/29/2016 11:34 AM 2013 Kia Optima L4-2.0L Turbo Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement Removal CAUTION: Use fender covers to avoid damaging painted
More information1997 Volvo 850 GLT. Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) Courtesy of VOLVO CARS OF NORTH AMERICA.
Fig. 2: Removing Drive Shaft, Engine Mount Bolt & Torque Arm (5-Cylinder) 4. Remove front exhaust pipe nuts and springs. Remove front exhaust pipe bolts. Disconnect speedometer. Remove engine mounting
More informationASSEMBLY. Transmission Automatic Transmission 5R44E and 5R55E. Special Tool(s)
307-01-1 Automatic Transmission 5R44E and 5R55E 307-01-1 ASSEMBLY Transmission Special Tool(s) Holding Fixture, Transmission 307-262 (T93T-77002-AH) Special Tool(s) Installer, Transmission Extension Housing
More information2013 Edge, MKX Workshop Manual
7. Remove the 3 bolts and the generator. Installation 1. Position the generator and hand tighten the 3 bolts. Tighten in the sequence shown. Tighten to 25 Nm (18 lb-ft). 2. Connect the generator electrical
More informationHeater/Vent Module Replacement
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2000 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN W Conversion
More informationSECTION Automatic Transaxle/Transmission 4R70E/4R75E
307-01-i Automatic Transaxle/Transmission 4R70E/4R75E 307-01-i SECTION 307-01 Automatic Transaxle/Transmission 4R70E/4R75E CONTENTS PAGE Transmission Four Wheel Drive (4WD)... 307-01-2 307-01-2 Automatic
More information303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid. REMOVAL Procedure revision date: 10/19/2012. Engine
2010 MKZ Report a problem with this article 303-01C Engine 3.5L 2010 Fusion, Milan, MKZ, Fusion Hybrid, Milan Hybrid REMOVAL Procedure revision date: 10/19/2012 Engine Special Tool(s) 2,200# Floor Crane,
More informationParts Manual SERIES CVT Lawn Tractor. Model LT1040 CUB CADET LLC, P.O. BOX CLEVELAND, OHIO PRINTED IN U.S.A.
Parts Manual CVT Lawn Tractor SERIES 000 Model LT00 PRINTED IN U.S.A. CUB CADET LLC, P.O. BOX CLEVELAND, OHIO -00 FORM -00C.fm (//00) SERIES 000 CVT LAWN TRACTORS TABLE OF CONTENTS DESCRIPTION PAGE Axle,
More information2005 Chevrolet Optra (CANADA) L4-2.0L
1 of 13 9/28/2013 7:54 PM 2005 Chevrolet Optra (CANADA) L4-2.0L Vehicle» Engine, Cooling and Exhaust» Engine» Timing Belt» Service and Repair Timing Belt Replacement Removal Procedure Caution: Refer to
More informationS/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly
1180 S/N 1H019H - 1H310H Page 1 of 33 46" Cutting Deck Assembly 1180 S/N 1H019H - 1H310H Page 2 of 33 46" Cutting Deck Assembly 1 17982 1 S Reinforcement Spindle Plate 2 618-0430 1 S Spindle Assembly w/
More informationMOROSO PERFORMANCE PRODUCTS, INC. (203) , 80 CARTER DRIVE GUILFORD, CT
Parts List (2) Air Oil separator (2) Billet Clamp (1) Stainless Mounting Bracket (2) Ball Valve (2) 90 Degree drain (2) ¼-20X1 SHCS (4) ¼-20x5/8 SHCS (2) ¼-20X1 HHCS (2) ¼-20 Nylock Nuts (2) ½ x 90 Barbed
More informationValve Body: Service and Repair
2007 Chevy Truck TrailBlazer 2WD L6-4.2L Copyright 2013, ALLDATA 10.52SS Page 1 Valve Body: Service and Repair Valve Body and Pressure Switch Replacement Removal Procedure 1. Ensure that removal of the
More information2001 Lincoln LS Workshop Manual
Page 1 of 10 SECTION 303-01B: Engine 3.9L 2001 Lincoln LS Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 05/16/2000 Intake Manifold Removal 1. Disconnect the battery ground cable. For additional
More informationZoom and Print Options
Vehicle» Engine, Cooling and Exhaust» Engine» Service and Repair» Removal and Replacement» Engine Replacement Engine Replacement ^ Tools Required - J 38185 Hose Clamp Pliers Removal Procedure 1. Remove
More information01 20 CRUISE CONTROL SYSTEM
01 20 CRUISE CONTROL SYSTEM LOCATION INDEX................. 01 20 1 CRUISE CONTROL MODULE REMOVAL/INSTALLATION......... 01 20 2 CRUISE CONTROL MODULE INSPECTION..................... 01 20 2 Terminal Voltage
More informationSECTION D Fuel Charging and Controls Turbocharger
303-04D-i Fuel Charging and Controls Turbocharger 303-04D-i SECTION 303-04D Fuel Charging and Controls Turbocharger CONTENTS PAGE Turbocharger Body On... 303-04D-2 303-04D-2 Fuel Charging and Controls
More informationRocker Lever Housing
003-013 Rocker Lever Housing Preparatory Steps Disconnect the air piping from the intake manifold. Remove the rocker lever cover. Refer to Procedure 003-011 in Section 3. Remove the engine brakes, if applicable,
More informationPage 1 of 5 303-01B Engine 3.0L (4V) 2004 Escape IN-VEHICLE REPAIR Procedure revision date: 05/26/2005 Engine Front Cover Material Removal Item Motocraft Metal Surface Cleaner ZC-21 Silicone Gasket and
More informationLower Arm. Special Tool(s) Lifting Bracket, Engine 303-D087 (D93P-6001-A1) Support Bar, Engine 303-F070
Lower Arm Special Tool(s) Lifting Bracket, Engine 303-D087 (D93P-6001-A1) Support Bar, Engine 303-F070 Item Part Number Description 1 W710141 Lower arm rearward flag bolt (2 required) 2 W709865 Lower arm
More information2013 Mustang Workshop Manual
32. Attach the wiring harness retainers to the LH side of the oil pan and the front oil pan stud bolts and install the 2 nuts. Tighten to 8 Nm (71 lb-in). 33. Position the underbody shield and install
More informationReturn to Instruction Sheet index TCI Installation Instructions for Turbo Hydramatic 350C & 250C
Page 1 of 6 Return to Instruction Sheet index TCI 326300 Installation Instructions for Turbo Hydramatic 350C & 250C NOTE: This kit was not intended for installation in transmissions that are in poor general
More informationDISASSEMBLY TRANSAXLE DISASSEMBLY AND ASSEMBLY. Part 1 Of 3
2004 Mitsubishi Truck Endeavor V6-3.8L SOHC Vehicle > Transmission and Drivetrain > Automatic Transmission/Transaxle > Service and Repair > Overhaul > F4A5A > Disassembly and Assembly DISASSEMBLY TRANSAXLE
More informationIntake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter)
Intake Installation Instructions P/N 9046 (red filter) - P/N 9046B (blue filter) P/N 9046K (black filter) Year/Make/Model/Engine 2012-17 Ford Focus 2.0L Parts List 1- Intake tube 1- Heat shield, Side 1-
More informationAUTO TRANS OVERHAUL - V.A.G. 01V Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site -
AUTO TRANS OVERHAUL - V.A.G. 01V Article Text 1998 Volkswagen Passat This file passed thru Volkswagen Technical Site - http://volkswagen.msk.ru ARTICLE BEGINNING 1997-98 AUTOMATIC TRANSMISSIONS Volkswagen/Audi
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi These instructions are based on a vehicle with an OEM turbocharger and top-mount intercooler. If a front-mount
More information2003 E-Series Workshop Manual
Page 1 of 20 SECTION 307-01B: Automatic Transmission 4R70W 2003 E-Series Workshop Manual ASSEMBLY Procedure revision date: 04/27/2006 Transmission Printable View (1828 KB) Special Tool(s) Dial Indicator
More informationSECTION Transaxle, Automatic-External Controls
07-05- 1 Transaxle, Automatic-External Controls 07-05- 1 SECTION 07-05 Transaxle, Automatic-External Controls SUBJECT PAGE SUBJECT PAGE ADJUSTMENTS REMOVAL AND INSTALLATION Shift Control Cale... 0705-12
More informationPage 6 of 6 OUTLAW DIESEL EGR COOLER DELETE KIT W/INTAKE ELBOW L FORD POWERSTROKE
What s in the box 1 Exhaust Block-Off Plate 1 Exhaust Gasket 2 Coolant Line Plugs 1 Brass Barbed Hose Connector 1 Stand-off Spacer 4 M10-1.25 x 40 Hex Head Bolts (Exhaust Manifold) 2 M10-1.25 x 20 Hex
More information1 of 13 10/12/2013 2:20 PM
1 of 13 10/12/2013 2:20 PM Coolant Pump, 4-cyl. Warning: Take care if the car is warm. The coolant is hot and there is also a risk of burning yourself on the manifold. To Remove 1. Open the cap on the
More informationS/N 1H019H - 1H310H Page 1 of 48 42" Cutting Deck Assembly
1170 S/N 1H019H - 1H310H Page 1 of 48 42" Cutting Deck Assembly 1170 S/N 1H019H - 1H310H Page 2 of 48 42" Cutting Deck Assembly 4 683-0254 1 S Deck Adjustment Bracket w/ Weld Nut 9 710-0528 1 /P Hex Cap
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION NOTE: For reassembly reference, label all electrical connectors, vacuum hoses and fuel lines before removal. Also place mating marks on engine hood and other major assemblies before
More informationBill of Materials for
Bill of Materials for 77060012 1 2-P5153572 Inlet Pipe 1 21-202M 2.75" Filter 1 103-BLO-4820N Filter Hose Clamp 1 559999 Washer, Fender M6x25 1 1-3028 Washer, 1/4 SAE Flat 1 1-2072 Bolt, 1/4-20-UNC x 1
More informationILLUSTRATED PARTS MANUAL
ILLUSTRATED PARTS MANUAL Wildcat Trail Model Number U2014W5T2PUSG Model Number U2014W5T2PUSR Model Number U2014W5T2PUSZ Model Number U2014W5T2POSG - International Model Number U2014W5T2POSR - International
More information2001 Ford Windstar ENGINES 3.8L V6 - VIN 4 - Windstar
COWL TOP VENT PANEL 1. Remove windshield wiper pivot arms. Remove cowl top vent panel retaining screws. Release cowl top vent panel retaining clips. Remove windshield wiper fluid hose. Remove cowl top
More information2003 Volkswagen Passat GL
2001-03 AUTOMATIC TRANSMISSIONS Removal & Installation - 01V APPLICATION TRANSAXLE APPLICATION Application Transaxle Model Passat 1.8L (FWD) 01V 2.8L (FWD & 4WD) 01V 4.0L (AWD) 2002-03 01V REMOVAL & INSTALLATION
More informationAPR, LLC
+ 1. 3 3 4. 5 0 2. 5 1 8 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 4 8 0 0 U S H W Y 2 8 0 W e s t, O p e l i k a, A l a b a m a 3 6 8 0 1 + 1. 3 3 4. 5 0 2. 5 1 8 1 NOTES:
More informationVehicle Level Engine, Cooling and Exhaust Engine Cylinder Head Assembly Service and Repair. Service and Repair
Page 1 of 7 Home Account Contact ALLDATA Log Out Help BILL SEIDLES MITSUBISHI Select Vehicle New TSBs Technician's Reference Component Search: OK 2001 Pontiac Sunfire L4-2.2L VIN 4 Conversion Calculator
More information1 of 7 7/22/2013 8:41 AM
1 of 7 7/22/2013 8:41 AM REMOVAL 1. Turn the steering wheel so that the vehicle's wheels are pointing straight ahead. 2. Turn the ignition switch to "LOCK". 3. Disconnect the battery "-" terminal cable,
More information235/245400, , 28N
Models 235/245400, 287000, 28N thru W, 310/312/313700 These carburetors have a fixed high speed main jet with adjustable idle, Fig 183. The different carburetors are identified as LMT 1 and up. The letters
More information2004 Nissan/Datsun Truck Quest Mini Van 3.5L SFI DOHC 6cyl Repair Guides Engin...
Page 1 of 10 SAVE 20% ON ONLINE SHIP-TO-HOME ORDERS OF $100 OR MORE. Use Code: MOM20 See Details Nissan Quest 2001-02 and 2004-06 REMOVAL & INSTALLATION Timing Chain Cover Removal & Installation 3.5L Engine
More information1 Green Pressure Regulator Spring Automatic transmissions operate at temperatures between 150ºF and
Installation Instructions for 603107 Valve Body Kit C-4 1970 & Later Tools Required Speed Handle or Ratchet 3/8 Drive 1/2 Socket 3/8 Drive 7/16 Socket 3/8 Drive 5/16 Socket 3/8 Drive Small Screwdriver
More informationTiming Chain Renew ( ) Remove. 2,0 DOHC-8V Engine. Special Tools Angle gauge A Universal flange-holding wrench
Timing Chain Renew ( 34 0) Special Tools 5-030A Universal flange-holding wrench 540-540 Angle gauge 5030A -47 Remover for vibration damper 68-68 Crankshaft immobilising tool 47 Remove. Standard preparatory
More informationKit Part Number:
10-677 Equipped with AEM DRYFLOW Filter No oil required! Kit Part Number: 21-677 Nissan 350Z 3.5L V6 2007-2008 CARB EO # D-392-30 Short Ram Intake Systems that are pending an Executive Order number (EO#)
More informationHR ZDX Throttle Body Install (06-11 Civic Si)
HR ZDX Throttle Body Install (06-11 Civic Si) This guide will walk you through the steps to install a ZDX throttle body onto your RBC Intake manifold using the Hybrid Racing ZDX adapter. Written By: Hybrid
More informationPage 1 of 13 2004 Chrysler PT Cruiser 2.4L Eng Touring Service Manual: AUTOMATIC TRANSMISSION - SERVICING ON-VEHICLE REPAIRS Tip: Trans pan leaking...maybe not. NOTE: Various components may be serviced
More information1994 Mazda MX-5 Miata. TRANSMISSION SERVICING - A/T TRANSMISSION SERVICING Mazda Automatic Transmission
IDENTIFICATION TRANSMISSION SERVICING - A/T 1990-94 TRANSMISSION SERVICING Mazda Automatic Transmission NOTE: On models with anti-theft radio system, obtain code number from customer to deactivate radio
More informationINSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) Turbo Subaru and STi Document# Support:
INSTALLATION INSTRUCTIONS AOS-R (Air Oil Separator-Return) 02-14 Turbo Subaru and 2015+ STi Document# 19-0102 Support: info@radiumauto.com These instructions are based on a vehicle with an OEM turbocharger
More informationDISASSEMBLY AND ASSEMBLY
307-01-1 Automatic Transaxle/Transmission 307-01-1 DISASSEMBLY AND ASSEMBLY Transaxle Special Tool(s) Dial Indicator Gauge With Holding Fixture 100-002 (TOOL-4201-C) Special Tool(s) Test Plate Screw Set,
More information* PLEASE READ INSTRUCTIONS PRIOR TO INSTALLATION *
XDP Duramax LBZ EGR Race Track Kit Item Number: XD165 PACKING LIST: 1 LBZ EGR Plate for Up Pipe 5 M8x1.25-20mm Bolt 2 M10x1.5 Flange Hex Nut 1 LBZ EGR Plate for Intake 1 M8x1.25-45mm Bolt 1 M8x1.25 Flange
More informationPage 1 of 8 Section 03-01: Engine, 4.6L IN-VEHICLE SERVICE 1994 Town Car/Crown Victoria/Grand Marquis Workshop Manual Oil Pan and Oil Pump Screen Cover and Tube Town Car Removal 1. Disconnect battery ground
More informationCERTAIN MODEL YEAR FUSION AND ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT
PAGE 1 OF 9 CERTAIN 2013-2016 MODEL YEAR FUSION AND 2013-2014 ESCAPE VEHICLES EQUIPPED WITH A 6F35 TRANSMISSION SHIFTER CABLE BUSHING REPLACEMENT OVERVIEW In some of the affected vehicles, the bushing
More informationALLDATA Online Toyota Camry L4-2.4L (2AZ-FE) - Rear Strut Assembly. Rear Strut Assembly
Page 1 of 11 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2004 Toyota Camry L4-2.4L (2AZ-FE) Conversion Calculator Vehicle
More informationINSTALLATION INSTRUCTIONS
Bill of Materials for 77070045AB A 1 9-0398 MOPAR Air Box B 1 MP-M-1011 Air Filter Assembly C 1 102507 Rubber Edge Trim 30-1/2 D 1 27368M Air Filter Adaptor Tube E 1 8-184 Elbow; Reducer 3/4-5/8 F 5 08373
More information1. Remove the battery tray. For additional information, refer to Battery Tray ( )
Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE
More informationExhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove
1 Page 1 of 20 Exhaust Gas Recirculation Valve, Replace J982500 Remove 1. Disconnect battery negative lead 2. Disconnect hose (1) from oil filler on air cleaner assembly, then move to one side Release
More information13A2693G190 LT-165 (2003) Page 1 of 31 Carburetor
13A2693G190 LT-165 (2003) Page 1 of 31 Carburetor 13A2693G190 LT-165 (2003) Page 2 of 31 Carburetor TC-640330 1 S Carburetor (Incl 184 of Engine Parts Lists) 1 TC-640035 1 Throttle Shaft & Lever Assembly
More informationPage 1 of 8 SECTION 303-01A: Engine 2.3L 2002 Ranger Workshop Manual IN-VEHICLE REPAIR Procedure revision date: 10/20/2004 Intake Manifold Removal 1. Remove the accelerator control snow shield. 2. Remove
More informationDescription. Cooling. Mechatronik module. Automatic Transmission (07.01) Transmission (07.00) transmission fault-finding.
Automatic Transaxle (07.01) Description The ZF 6HP26 automatic gearbox has the following features: Six forward speeds and One reverse A torque converter with an integral converter lock-up clutch Electronic
More information2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
More information