PETROL CHAINSAW - THPCS18

Transcription

1 PETROL CHAINSAW - THPCS18 21/03/2014 v1

2 CONTENTS

3

4 PULL CHAIN OIL MAX MIN The indication regarding the chain oil adjuster nut. MIN direction - the oil flow decreases MAX direction- the oil flow increases Position: bottom of the clutch side WPL7RTM with adjuster 7T X 0.325" 410 x 235 x 265 (mm) 7.5 (kg) Sprocket nose - 18" (45cm) 21VB (in) (in)

5 Wearing gloves locate the guide bar onto the chainsaw making sure that the hole on either side of the slot locates over the adjuster pin. Note: A new chain will stretch during its first use. Turn off the engine then check and readjust the chain frequently. Use a ratio of 25:1 unleaded petrol to 2-stroke mineral oil. For semi-synthetic or synthetic use the manufacturer s ratio. Mix in an appropriate mixing bot- CHAIN OIL Use Handy chain oil HP-177

6 The chain oil flow can be adjusted by inserting a screwdriver in the hole on the bottom of the machine. Adjust accoring to your work conditions 1

7

8

9 (1) Sprocket (2) Needle bearing (3) Clutch drum (4) Spacer (5) Clutch shoe F31

10 3/16in (4.76mm) e 21VB 21VB 0.25 (0.65mm) 21VB 0.25 (0.65mm) 850

11

12 PARTS DIAGRAM

13 PARTS LIST No Part No Description Qty No Part No Description Qty 1 WPL7RTM Spark Plug 1 58 TH Foam Seal 1 2 TH206-2 Board 1 59 TH Small Oil Seal 15x28x5 1 3 TH206-3 Bolt M5x TH Snap Ring 1 4 TH206-4 Cover 1 61 TH Vent Filter 1 5 TH206-5 Switch Block 1 62 TH Air Outlet Connector 1 6 TH206-6 Nut M TH Plug Pad 3 7 TH206-7 Muffler Cover 1 64 TH Rubber Cushion Pad 3 8 TH206-8 Bolt M5x TH Bar Plate 1 9 TH206-9 Muffler 1 66 TH Bolt M4x TH Muffler Gasket 1 67 TH Right Pad 2 11 TH Muffler Bolt 2 68 TH Right Pad Rubber Cushion 1 12 TH Bolt M5x TH Right Crank Case 1 13 TH Cylinder 1 70 TH Pin 6x TH Gylinder Gasket 1 71 TH Bearing TH Piston Ring 2 72 TH Snap Ring 2 16 TH Piston Ring 1 73 TH Small Bearing 1x15x TH Snap Ring 2 74 TH Crankshaft Conrod Assembly 1 18 TH Piston Pin 1 75 TH Flywheel Key 3.3x7x TH Carburetor Gasket 1 76 TH Gasket 1 20 TH Chain Catcher 1 77 TH Hose Spring Clip 1 21 TH Bolt M4x TH Hose Pulse 1 22 TH Plastic Ring 1 79 TH Hose Pulse Spigot 1 23 TH Damping Spring 1 80 TH Bolt M5x TH Bolt ST4.8x TH Wire Clamp 1 25 TH Intake Gasket 1 82 TH Boot Carburetor 1 26 TH Intake 1 83 TH Snap Ring TH Bolt M5x TH Outer Gromet 1 28 TH Bolt M5x TH Left Crankcase 1 29 TH Carburetor Support 1 86 TH Left Pad Rubber Cushion 1 30 TH Carburetor Support Gasket 1 87 TH Bolt M5x TH Carburetor Flange 1 88 TH Bolt M5x TH Carburetor Eyelet 1 89 TH Large Oil Seal 15x35x TH Carburetor Assembly 1 90 TH Oil Cap Stopper 2 34 TH Inner Gromet 1 91 TH Oil Cap Rubber Washer 1 35 TH Rubber Cap 1 92 TH Oil Tank Cap 1 36 TH Bolt M5x TH Oil Seal Gasket Plate 1 37 TH Air Filter 1 94 TH Bolt M4x TH Air Filter Cover 1 95 TH Flywheel Assembly 1 39 TH Nylon Gasket 1 96 TH Snap Ring Spring TH Air Filter Knob 1 97 TH Nut M8x TH Stud Bar M8x TH Bolt ST4.8x TH Clutch Frame 1 99 TH Washer 5x TH Clutch Spring TH Starter Assembly 1 44 TH Clutch TH Starter Spring Cover 1 45 TH Clutch Washer TH Starter Spring Cover 1 46 TH Clutch Drum TH Outer Gromet 1 47 TH Sprocket TH Recoil Housing 1 48 TH Needle Bearing TH Bolt M5x TH Worm Gear TH Rope Snap 1 50 TH Choke Knob Washer TH Inner Ring 2 51 TH Choke Knob TH Recoil Spring 1 52 TH Choke Knob Damper TH Recoil Handle 1 53 TH Bolt M5x TH Recoil Rope 1 54 TH Oil Pump Cover TH Front Handle 1 55 TH Oil Outlet Hose TH Bolt ST4.8x TH Bolt M4x TH Bolt M5x TH Oil Pump TH Ignition Coil Assembly 1

14 PARTS LIST No Part No Description Qty No Part No Description Qty 115 TH Air Baffle TH Brake Lever TH Oil Hose TH Pin 3X TH Oil Filter TH Brake Band TH Fuel Tank Cap TH Spring Actuator TH Fuel Tank Cap Rubber Washer TH Spring Actuator TH Primer Bulb & Pipes Assembly TH Brake Plate TH Large Plug TH Pin TH Nut TH Bolt ST4.2x TH Large Plug Housing TH Adjustor Cover TH Pin TH Rubber Strap TH Trigger Lever (142) TH Chain Adjustor Sprocket TH Trigger Spring TH Chain Tooth Adjustor TH Double Screw Cushion TH Adjustor Pin TH Fuel Tank TH Pin TH Throttle Rod TH Snap Ring TH Balance Cap TH Brake Plate TH Balance TH Gasket Ring TH Balance Cover TH Snap Ring TH Balance Support TH Gasket Ring 6X TH Fuel Filter TH Brake Spring TH Fuel Pipe Ring TH Chain Brake Lever TH Fuel Pipe TH Pin TH Inlet Pipe TH Chain Brake Housing TH Fuel Pipe TH Rubber Plate TH Fuel Return Pipe TH Flange Nut M TH Fuel Support Pipe TH Bolt M5x TH Rear Handle TH Spike TH Trigger Lever (125) TH Oregon 18" Guide Bar TH Cover TH Oregon 18" Chain TH Primer Bulb 1 ZC1 TH206-ZC1 Crankshaft Assembly TH Ignition Switch 1 ZC2 TH206-ZC2 Recoil Assembly TH Bolt ST4.8x19 1 ZC3 TH206-ZC3 Clutch Assembly TH Rubber Dustproof Plate 1 ZC4 TH206-ZC4 Chain Brake Assembly TH Screw ST4.2x9.5 4 ZC5 TH206-ZC5 Balance Assembly TH Brake Spring Cover 1

15 EC Declaration of Conformity We, Importer Handy Distribution SN3 4NS Declare that the product Designation: 46cc PETROL CHAINSAW Model: THPCS18 Complies with the following directives: 2006/42/EC / Annex IV - Machinery Directive 2004/108/EC - Electromagnetic Compatibility Directive 2000/14/EC amended by 2005/88/EC - Noise Emission in the Environment by Equipment for Use Outdoors Directive. The conformity assessment procedure followed was in accordance with Directive 2006/42/EC Name of the Notified Body: TÜV SÜD Product Service GmbH Address: Ridlerstraße München - Measured Sound Pressure Level: 96.7 db (A) - Guaranteed Sound Power Level: 110 db (A) Standards and technical specifications referred to: 2006/42/EC / Annex IV - EN 954-1, ISO 6531:2008, ISO 6533:2001, ISO 6534, ISO 6535, ISO 7293, ISO 7914, ISO 7915, ISO 8334, ISO 9518, ISO 10726:1992, ISO 11680, EN ISO , EN ISO A:2011, ISO 11684:1995, ISO/TR , ISO/TR , ISO 11691, ISO 11820, EN , ISO 12100:2010, ISO 13772, ISO :2006, EN ISO , ISO 13857: 2008, EN ISO :2007, ISO 14163, ISO 14982:1998, ISO 17080:2005, ISO 22867, ISO 22868, IEC :2006, EN60825, EN 62061, ZEK /11.11 Authorised signatory and technical file holder Date: 21/03/2014 Signature: Name / title: Mr. Simon Belcher / Managing Director Hobley Drive, Stratton St Margaret, Swindon, Wiltshire, SN3 4NS.

16 GUARANTEE This product is guaranteed against manufacturing defects for a period of 12 months. This does not cover the product where the fault is due to misuse, abuse, use in contravention of the instructions, or where the product has been the subject of unauthorised modifications or alterations. This warranty only covers domestic use and will be void if the tool is used for a commercial application. In the event of a problem with the product within the guarantee period, please contact Customer Service on or customerservice@handydistribution.co.uk. If the issue cannot be resolved over the telephone or by , you may be referred to your local approved service dealer. Please keep your sales receipt as proof of purchase Your statutory rights remain unaffected. Guarantor: Handy Distribution SN3 4NS Whilst every effort is made to accurately represent the product, small variations in colour, design and specification may occur. We reserve the right to alter the product without giving notice. All images are illustrative only and may differ from the product due to ongoing product development.

17 A SELECTION OF QUALITY PRODUCTS FROM OUR VAST RANGE HAND PUSH LAWN MOWERS ELECTRIC & PETROL BLOW VACS ELECTRIC & PETROL SHREDDERS ELECTRIC, PETROL & MANUAL LOG SPLITTERS LAWN SWEEPERS PETROL LINE TRIMMERS PETROL BRUSHCUTTERS PETROL MULTICUTTERS ELECTRIC & PETROL CHAINSAWS LOG SAW HORSES CORDLESS & PETROL HEDGETRIMMERS ELECTRIC & PETROL TILLERS AERATORS & DETHATHERS GARDEN & SALT SPREADERS PUSH & TOWED ROLLERS SNOW CLEARANCE TOOLS SPRAYERS SACK TRUCKS TROLLEYS & TRAILERS LIGHT CONSTRUCTION FIND OUT MORE AT

18 NOTES

19

20 To order spare parts and see the complete range of garden machinery and garden equipment from Handy, visit: Spares & Support: