TEC Actuator Package. Product and Part Numbers. Product Description. Installation Instructions Document No October 27, 2010 CAUTION:
|
|
- Sharleen Davis
- 5 years ago
- Views:
Transcription
1 Document No TEC Actuator Package AUTOZERO MODULE (OPTIONAL) CABLE TIE TEC00R BASE-PLATE Figure. TEC Actuator Package, with Optional Autozero Module. DO NOT CUT CABLE TIE FASTENED AROUND ACTUATOR Cable tie (Figure ) must be left in place until AFTER the actuator set screw has been tightened and the TEC Actuator Package has been screwed in place on the mounting surface. Product Description The TEC Actuator Package consists of a Terminal Equipment Controller, a Siemens OpenAir GDE series electronic actuator, and if required, an Autozero Module (AZM). Components are factory mounted on a common base-plate with all connections in place (Figure ). The shipping carton includes the TEC Actuator Package, two self-tapping screws, a hex wrench, and a metal insert for damper shafts measuring /8-inch (8-0 mm) in diameter. NOTE: These instructions include a section near the end on replacing the actuator. Product and Part Numbers Product TEC Variable Volume Description Autozero Module * * * Constant Volume * * * Actuator GDE.U* *To replace a component, order the individual component part number, not the product number. Item Number: , Rev. GA Page of 7
2 Parts for CE Compliance Product Description Clamp-on ferrite filter (0 pack) series Approved -RJ RTS cable in 5-inch, 50-inch, or 00-inch (7.6-m, 5.-m, 0.48-m) Large Equipment Controller Enclosure Required Tools /4-inch hex nut driver Electric drill and /8-inch ( mm) drill bit (or other bit size) if self-tapping screws are not used Small, flat-blade screwdriver 4-mm hex wrench (supplied) Torque wrench Pencil Pliers Ruler (or something to measure diameter of damper shaft) Wire cutters Caution Notation Prerequisites Page of 7 Equipment damage may occur if you do not follow a procedure as specified. All wiring must conform to NEC and local codes and regulations. The mounting screws provided are designed for common sheet metal duct surfaces. Have appropriate mounting hardware on hand if another surface is used. NOTE: If the controller is being installed on a box with or more stages of electric heat, the MOV with pre-terminated spade connectors must be installed across the manufacturer-supplied airflow switch. MOVs can be installed at the time the controller is factory-mounted; coordinate with the box manufacturer prior to order placement. For field installation, see Metal Oxide Varistor Kit ( ). Protect the TEC Actuator Package from metal shavings when drilling holes in the enclosure or mounting surface. Metal shavings can severely damage the controller. Expected Installation Time 8 minutes Instructions For actuator replacement, see Actuator Replacement section later in these instructions. DO NOT cut the cable tie (Figure ) that secures the actuator until step 8.. Determine the damper shaft diameter. Do one of the following: If it measures /-inch ( to 4 mm), skip to step. If it is not /-inch ( to 4 mm), remove the black plastic guide piece from the hub of the actuator (Figure ). NOTE: If necessary, you may destroy the guide piece in order to remove it.. Do one of the following: If the shaft diameter measures /8-inch (8 to0 mm), install the metal insert into the actuator hub (Figure ). If the shaft diameter measures 5/8-inch (5 to7 mm), no insert is necessary. The metal insert MUST be used if the damper shaft diameter equals /8-inch. Using pliers if necessary, rotate the damper shaft counterclockwise until it fully stops. Mark the end of the shaft for reference if it is not already marked.. Confirm that the actuator s adjustment lever is also in counterclockwise position; adjust if necessary (Figure 4).
3 The TEC circuit board and the actuator have little clearance between them. If the actuator is secured with its adjustment lever in clockwise position (instead of counterclockwise as called for in step 4), the slight side-to-side movement of the actuator during normal operation will be toward the circuit board instead of away from it. If the actuator impacts the circuit board, equipment damage may result. 4. Position the TEC Actuator Package onto the damper shaft. Raised Notches Go In Last Damper Shaft Metal Insert TEC004R TEC08R Figure. Guide Piece Removal (Shaft Size Not /-Inch). Figure. Installing Metal Insert for /8-Inch Shafts. ADJUSTMENT LEVER ADJUSTMENT LEVER 4 mm 60- lb-in (7-0 Nm) Torque (SETSCREW) MANUAL TEC00R TEC00R AUTO Adjust if necessary using manual override. DO NOT remove actuator from base-plate. Figure 4. Actuator Initial Position. Page of 7
4 5. Hold the TEC Actuator Package steady and tighten the set screw (Figure 4) to the following inch pounds of torque: 60 inch pounds solid steel or plastic graphite composite (hollow steel shafts require an insert to prevent shaft damage!) 8 inch pounds hollow aluminum shafts Save the hex wrench. It is EXTREMELY IMPORTANT to fully tighten the set screw. Loose set screws are the leading cause of actuator control failure. CLOSED Typical Position of TEC Actuator Package On Damper Shaft CLOCKWISE OPEN I II OPEN SCREW PLACEMENT II I CLOCKWISE OPEN = & COUNTERCLOCKWISE OPEN = & 4 4 TEC005R4 For Clockwise Open, Screws Placed in or 4 May Impede Movement of Damper Blade Figure 5. Screw Placement. 6. After viewing Figure 5, secure the base plate with only two self-tapping screws (using more may obstruct the damper s range of motion). 7. Cut and remove the cable tie, confirming release of the location pin (Figure 6) to its neutral position. Push it free if stuck. Page 4 of 7
5 CUT AND REMOVE LOCATION PIN TEC006R4 Figure 6. Confirming Release of Location Pin. 8. If a mechanical range (damper stop) adjustment is necessary, do it now (Figure 8). Damper Position In most cases, you will want to finish with the damper in open position so that airflow through ductwork will not be obstructed. Since most boxes open clockwise, the damper is probably closed at this point in these instructions. (If this is not the case that is, the damper is open in counterclockwise position then installation is complete.) Place the filter - cm from the end of the cable or wiring to be shielded. Wind the cable tightly twice around the filter. - cm Proceed with step 9 if the damper is in counterclockwise position and closed. 9. Manually open the damper clockwise using the actuator s adjustment lever. Use the hex wrench for leverage if necessary (Figure 9). The installation is complete. CE Compliance If CE compliance is required, the Equipment Controller must be mounted in a grounded metal enclosure and a ferrite filter must be placed approximately cm from the end of the cable being shielded (RTS cable and point wiring for AI), Figure 7. TEC00R Close the filter and wrap with a zip tie. Figure 7. Ferrite filter(s) for CE. Additional Information Important warning on accessory kit holes Figure 8 Releasing TEC from base-plate Figure Dimensions Figure 5 For more information on the Siemens OpenAir GDE Series Electronic Actuator used with the TEC Actuator Package, see OpenAir Electronic Damper Actuator GDE/GLB Rotary Non-spring Return (9-67). Page 5 of 7
6 THESE HOLES FOR ACCESSORY KITS ONLY. NEVER USED FOR ACTUATOR INSTALLATION. TEC09R Figure. TEC Removal. Pull Back Tab to Release TEC TEC00R TEC008R mm Figure 8. Accessory Kit Holes ONLY. Loosen the stop set screw, move to desired position and tighten. Figure 9. Setting a Mechanical Range Stop. TEC009R 4 mm 60- lb-in (7-0 Nm) Torque Actuator Replacement. Remove the terminal block from the TEC and disconnect actuator wiring.. Using the hex wrench supplied, loosen the old actuator s set screw (see Figure 5 for set screw). Remove actuator and set aside.. Determine the damper shaft diameter. Do one of the following: If it measures /-inch ( to 4 mm), skip to step 5. If it is not /-inch, remove the black plastic guide piece from the hub of the new actuator (Figure ). 4. Do one of the following: If the shaft diameter measures /8-inch (8 to 0 mm), install the metal insert into the actuator hub (Figure ). If the shaft diameter measures 5/8-inch (5 to 7 mm), no insert is necessary. The metal insert MUST be used if the damper shaft diameter equals /8-inch. TEC007R AUTO MANUAL Figure 0. Opening the Damper. 5. Refer to steps and 4 of the Instructions section and place the damper shaft and replacement actuator both in full counterclockwise position before proceeding. 6. Place actuator over damper shaft in correct position on the TEC Actuator Package. Tighten the set screw to the following inch-pounds of torque: 60 inch pounds solid steel or plastic graphite composite (hollow steel shafts require an insert to prevent shaft damage!) 8 inch pounds hollow aluminum shafts Page 6 of 7
7 It is EXTREMELY IMPORTANT to fully tighten the set screw. Loose set screws are the leading cause of actuator control failure. Damper Shaft Metal Insert 7. Connect the actuator wiring (Figure ) to the terminal block and plug the terminal block back into the TEC. The replacement is complete. Raised Notches Go In Last TEC00R Figure. Installing Metal Insert for /8-inch Shafts EA0999R TEC0R Y (ORANGE) G (RED) Y (VIOLET) ACTUATOR AUTOZERO MODULE For counter-clockwise rotation, reverse violet and orange. Figure. Guide Piece Removal (Shaft Size not /-Inch). Figure 4. Actuator and Autozero Module Wiring. 8-5/8 (9) 8-5/8 (9) -9/ () -7/8 (98) 0.5 (.7) 8-/4 (0) 6-/6 (70) 5-/6 (44) 5-/ (44) 4-5/6 (0) TEC07R4 0-/6 (59) -9/6 (40) -/8 (79) Figure 5. Dimensions in Inches (Millimeters). Information in this publication is based on current specifications. The company reserves the right to make changes in specifications and models as design improvements are introduced. Products or company names mentioned herein may be the trademarks of their respective owners. 00 Building Technologies Division 000 Deerfield Parkway Buffalo Grove, IL USA Tel Your feedback is important to us. If you have comments about this document, please send them to SBT_technical.editor.us.sbt@siemens.com. Document No Printed in the USA Page 7 of 7
OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary
EA GDE/GLB-2 OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary Description OpenAir non-spring return, 24 Vac, floating control, direct-coupled, actuators
More informationBall Valve Bracket Kit
Installation Instructions Document No. 129-496 Ball Valve Bracket Kit Product Description The Ball Valve Bracket Kit contains the parts necessary to install an OpenAir GDE/GLB Series non-spring return
More informationSKD U Electronic Valve Actuator
Document No. 129-217 SKD U Electronic Valve Actuator Product Description The SKD U actuator requires a 24 Vac supply signal to control a Flowrite 599 Series valve with a 3/4-inch (20 mm) stroke. Product
More informationSAX Electronic Valve Actuator
Document No. 129-561 SAX Electronic Valve Actuator Product Description The SAX Electronic Valve Actuator requires a 24 Vdc or 24 Vac, Class 2, supply signal to control a Flowrite 599 Series valve or a
More informationOpenAir Electronic Damper Actuators GLB Series Enhanced Non-spring Return Rotary
Document No. 155-785 OpenAir Electronic Damper Actuators GLB Series Enhanced Non-spring Return Rotary Description The OpenAir direct coupled enhanced non-spring return rotary electric actuators are designed
More informationOpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return Rotary 24 Vac 3-position Control
OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return Rotary EA GDE/GLB-2 Description OpenAir direct coupled 24 Vac non-spring return rotary electric actuators are designed for 3-position (floating)
More informationSKD U Electronic Valve Actuator
Document No. 129-217 SKD U Electronic Valve Actuator Product Description The SKD U actuator requires a 24 Vac supply signal to control a Flowrite 599 Series valve with a 3/4-inch (20 mm) stroke. Mounting
More informationSKD62UA Series Electronic Valve Actuator, Advanced Features
Document No. 29-69 October 6, 22 SKD62UA Series Electronic Valve Actuator, Advanced Features Product Description The SKD62UA electronic valve actuator requires a 24 Vac supply and receives a to Vdc or
More informationPowers TM Controls EA 338 Electronic Actuator
Powers TM Controls Technical Instructions Document No. 155-136P25 EA 338-1 Description Features 24 Vac power supply. The s are used with floor mount linkage kits to operate dampers in HVAC installations.
More informationPowers Controls 656 Powermite Valve with 3-inch Top Rebuilding
Powers Controls 656 Powermite Valve with 3-inch Top Rebuilding Technical Bulletin Document No. 155-240P25 TB 233 Description This Technical Bulletin describes the recommended method of rebuilding the 656
More informationOpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary
EA GDE/GLB-2 OpenAir Electric Damper Actuator GDE/GLB Series Non-spring Return, 24 Vac Floating Control, Rotary Description OpenAir non-spring return, 24 Vac, floating control, direct-coupled, actuators
More informationSmartX MF and MS
schneider-electric.com 1 SmartX MF41-6043 and MS41-6043 Non-Spring Return Direct-Coupled Actuators Figure-1 Parts of the SmartX Rotary Actuator Product Description These installation instructions describe
More informationPacking Replacement Kit for Flowrite VF 599 Series Valves
Document No. 29-25 Packing Replacement Kit for Flowrite VF 599 Series Valves Product Description This kit contains a packing cartridge assembly and copper gasket to replace either the normal duty or high
More informationRebuild/Repack Kits for Flowrite VF 599 Series 2-1/2 to 6-inch Valves
Document No. 129-216 Rebuild/Repack Kits for Flowrite VF 599 Series 2-1/2 to 6-inch Valves Product Description This kit contains the parts necessary to rebuild and repack either the normal duty or high
More informationLaboratory Exhaust Air Terminal
Document No. 546-00335 Laboratory Exhaust Air Terminal Product Description The Laboratory Exhaust Terminal (LGE) is a onepiece flow control device used to vary airflow through an exhaust duct. See Figure
More informationOpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc
Technical Instructions Document No. 155-187P25 EA GDE/GLB-1 OpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc Description The OpenAir direct
More informationPowers TM Controls RL 243 SW Switching Relay
Powers TM Controls RL 243 SW Switching Document No. 155-040P25 RL 243-4 Description The Powers 243 SW Switching is a two-position, pilot-operated auxiliary device used for switching a common part from
More information599 Series Zone Valves
599 Series Zone Valves SFA/SFP Electronic Valve Actuator 2-Position Control Document No. 129-335 Product Description The SF Series actuator requires a 24 Vac, 120 Vac, 208 Vac, or 277 Vac Class-2 supply
More informationProduct Description. Product Numbers. Warning/Caution Notations. Required Tools. Wiring. Prerequisites
Document No. 155-302N VE 598 Electronic Flowrite Valve Field Assembly Product Description The VE 598 Electronic Valve Assemblies consist of an electronic actuator, linkage kit, and a valve body assembly.
More informationMF Series MS Series
MF41-6043 Series MS41-6043 Series DuraDrive Non-Spring Return Direct Coupled Actuator General Instructions Figure-1 Parts of the DuraDrive Rotary Actuator. Product Description These installation instructions
More informationSED2-BT300-XX-C09 Migration Kits. Product Numbers
Document No. 129-710 SED2-BT300-XX-C09 Migration Kits Product Numbers SED2-BT300-AB-C09 Migration Kit, SED2 FSAB 09 to BT300 FS4 * 208 Vac: Up to 3 hp 480 Vac: Up to 5 hp SED2-BT300-C4-C09 Migration Kit,
More informationOpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc
Document No. 155-187P25 EA GDE/GLB-1 OpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc Description The OpenAir direct coupled 24 Vac non-spring
More informationMaster/Slave Actuators Spring Return Rotary 24 Vac - Modulating Control
Document No. 129-312 Master/Slave Actuators Spring Return Rotary 24 Vac - Modulating Control a PL0038R1 c b d e f g i Figure 1. Parts of the Master/Slave Actuators. h a. Actuator b. Shaft adapter c. Position
More informationOpenAir GBB/GIB Series Electronic Damper Actuators Non-Spring Return, 24 Vac, Modulating Control
OpenAir GBB/GIB Series Electronic Damper Actuators Non-Spring Return, 24 Vac, Modulating Control Document No. 155-176P25 EA GBB/GIB-1 Description The OpenAir, non-spring return (NSR), 24 Vac, rotary, direct-coupled,
More informationSED2 Variable Frequency Drives
Document No. 129-371 SED2 Variable requency Drives Product Description SED2 Variable requency Drives (VDs) control pumps and fans in HVAC applications. Product Numbers SED2 Variable requency Drives (VDs)
More informationPowers Controls No. 6 Damper Actuators Tandem Mounting
Document No. 155-277P25 Powers Controls No. 6 Damper Actuators Tandem Mounting Description The No. 6 Damper Actuators - Tandem Mounting consist of two No. 6 actuators piloted by a positioning relay mounted
More informationBall Valve Bracket Kit
Document No. 19-96 July 1, 010 Ball Valve Bracket Kit Product Description The Ball Valve Bracket Kit contains the parts necessary to install an Openir GDE/GLB, series non-spring return actuator or Openir
More informationOpenAir GBB/GIB Series Electronic Damper Actuators Non-Spring Return, 24 Vac, Modulating Control
OpenAir GBB/GIB Series Electronic Damper Actuators Non-Spring Return, 24 Vac, Modulating Control Technical Instructions Document No. 155-176P25 EA GBB/GIB-1 Description The OpenAir, non-spring return (NSR),
More informationTechnical Instructions Document No EA GQD May 6, OpenAir GQD Series. Spring Return, 20 lb-in (2 Nm), Rotary Electronic Damper Actuators
OpenAir GQD Series Spring Return, 20 lb-in (2 Nm), Rotary Electronic Damper Actuators Technical Instructions Document No. 155-760 EA GQD Description Features Application The OpenAir GQD Series direct-coupled
More informationOpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc
Document No. 155-187P25 EA GDE/GLB-1 OpenAir Electric Damper Actuators GDE/GLB Series Non-spring Return Rotary 24 Vac - Modulating Control 0 to 10 Vdc Description The OpenAir direct coupled 24 Vac non-spring
More informationSeries 1000 Room Temperature Sensors, 1K Ω Platinum (375α) RTD (MBC/RBC/MEC/UC)
Document No. 540-743 Series 1000 Room Temperature Sensors, 1K Ω Platinum (375α) RTD (MBC/RBC/MEC/UC) Product Description These sensors work with the Modular Building Controller (MBC), Remote Building Controller
More informationFlowrite TM AP 599 Series 8-inch Pneumatic Valve Actuator
Flowrite TM AP 599 Series 8-inch Pneumatic Valve Actuator Technical Instructions Document No. 155-161P25 AP 599-1 Description Features Application The Flowrite AP 599 Series 8-inch pneumatic valve actuator
More informationPOWERS TM CONTROLS SW 786 Selector Switch
POWERS TM CONTROLS SW 786 Selector Switch Document No. 155-062P25 SW 786-1 Description The SW 786 Selector Switches are designed to deliver, stop, or redirect a pneumatic signal to air operated control
More informationOpenAir Electric Damper Actuators GBB/GIB Series NSR Rotary 24 Vac - Modulating Control
Document No. 155-176P5 EA GBB/GIB-1 OpenAir Electric Damper Actuators GBB/GIB Series NSR Rotary 4 Vac - Modulating Control Description The OpenAir direct coupled 4 Vac non-spring return (NSR) rotary electric
More informationPowers Controls Maximum Thrust Ratings of Pneumatic Damper Actuators
Powers Controls Maximum Thrust s of Pneumatic Damper Actuators Document No. 155-219P25 TB 181 Description Actuator force or thrust is expressed in total net pounds of force available at the actuator shaft.
More informationUniTrak Sensor Assembly Kit Horizontal, Vertical, and Combination Sashes
Document No. 546-00449 UniTrak Sensor Assembly Kit Horizontal, Vertical, and Combination Sashes Product Description The UniTrak Sensor Assembly Kit contains the hardware to complete one fume hood sensor
More informationPOWERS Controls No. 4 Pneumatic Damper Actuator
POWERS Controls No. 4 Pneumatic Damper Actuator Technical Instructions Document No. 155-032P25 AP 331-2 Actuator Assembly 331-2929 Typical Actuator Assembly 331-2904 Typical Actuator Assembly 331-3000
More informationDodge Engineering & Controls, Inc. Toll Free (877) Fax: (978) EN44 and EN88 Non-Spring Return Electronic Actuators
Dodge Engineering & Controls, Inc. EA678R3 45 a b e d c a. Actuator b. Position indicator c. Mounting bracket (for dampers) d. Mounting screws e. 4 mm hex wrench Figure 1. Parts of the EN44 and EN88 Actuators.
More informationSED2 Variable Frequency Drive Electronic Bypass (E-Bypass) Options
SED2 Variable Frequency Drive Electronic Bypass (E-Bypass) Options Product Description The SED2 Electronic Bypass (E-Bypass) Options are companion packages for the family of SED2 Variable Frequency Drives
More informationFlowrite AP 599 Series
AP 599-2 Flowrite AP 599 Series 12-inch Pneumatic Valve Actuator Description The Flowrite AP 599 Series 12-inch pneumatic valve actuator is designed for use with the Flowrite VF 599 Series valves. This
More informationPOWERS Controls. Technical Instructions Document No P25 AP December 3, No. 6 Pneumatic Damper Actuator.
POWERS Controls No. 6 Pneumatic Damper Actuator Technical Instructions AP 331-3 331-2793 Actuator 331-2857 Actuator with Clevis and Pin 331-3012 Extended Shaft and Frame Mounting Description The POWERS
More informationRoom Temperature Sensors Series to 20 ma
Document No. 54035 Room Temperature Sensors Series 000 4 to 0 ma Product Description These Room Temperature Sensors work with any controller that accepts a 4 to 0 ma signal input. The sensors detect room
More informationPowers Controls Powertop Two-Way Valves Normally Open
Powers Controls Powertop Two-Way s Normally Open VP 658-5 Description The VP 658 normally open valves are pneumatically operated valves designed to control the flow of both water and steam. Features Stainless
More informationPOWERS TM CONTROLS LC Pneumatic Damper Actuator
POWERS TM CONTROLS Document No. 155-030P25 AP 331-4 Description Features The LC Actuator is a piston type pneumatic actuator. Air pressure is supplied to both sides of the piston to provide a force balance
More informationPowers TM Controls SW 134 Pressure Electric Switch (Adjustable Differential)
Powers TM Controls SW 134 Pressure Electric Switch (Adjustable Differential) Document No. 155-050P25 SW 134-3 Description The SW 134 Pressure Electric Switch actuates electrical circuits from pneumatic
More information599 Series 6-Way Ball Valves
Technical Instructions Document No. 155-803 599 Series 6-Way Ball Valves Description The 599 Series 6-way ball valves couple with the Siemens GDE161.1P OpenAir modulating actuator to provide single valve
More informationFlowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac 3-Position (Floating) Control
Flowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac 3-Position (Floating) Control Technical Instructions EA 599-5 Description The Flowrite EA 599 Series SKD electronic valve actuator requires a
More informationPowers Controls RL 147 Positioning Relay
Powers Controls Technical Instructions Document No. 155-038P25 RL 147-2 Description Features Rapid response Product Numbers See Table 1. The is a compact, pneumatic device designed to provide positive
More informationTechnical Instructions Document No P25 EA GMA May 19, OpenAir. GMA Series, Spring Return, 62 lb-in, Rotary, Electronic Damper Actuators
OpenAir GMA Series, Spring Return, 62 lb-in, Rotary, Electronic Damper Actuators Document No. 155-315P25 EA GMA Description The OpenAir direct-coupled spring return electronic actuator is designed for
More informationPowermite 599 Series MZ Series SSB Electronic Valve Actuator 24 Vac Floating Control
Powermite 599 Series MZ Series SSB Electronic Valve Actuator EA 599-13 Description Features Application The Powermite 599 MZ Series SSB electronic valve actuator requires a 24 Vac supply floating control
More informationPowermite 599 Series MZ Series SSB Electronic Valve Actuator 24 Vac Proportional Control
Powermite 599 Series MZ Series SSB Electronic Valve Actuator EA 599-10 EA0579R2 Description The Powermite 599 MZ Series SSB Electronic Valve Actuator requires a 24 Vac supply and receives a 0 to 10 Vdc
More informationPowers TM Controls Three-way Electro-pneumatic (EP) Valve Model 2
Powers TM Controls Three-way Electro-pneumatic (EP) Valve Model 2 Document No. 155-078P25 VE 265-2 Description The VE 265 Electro-Pneumatic Valve is a general purpose, electrically operated, twoposition
More informationFlowrite EA 599 Series SQX Electronic Valve Actuator 24 Vac, 3-Position Control
Flowrite EA 599 Series SQX Electronic Valve Actuator 24 Vac, 3-Position Control Technical Instructions EA 599-7 Description The Flowrite EA 599 Series SQX electronic valve actuator requires a 24 Vac supply
More informationDC-44 and DC-88 Series Non Spring Return Electronic Actuator Installation Instructions
"" Delta Control Products, Inc. West Rose Garden Lane Phoenix, Z 857 6-78-48 DC-44 and DC-88 Series Non Spring Return Electronic ctuator Installation Instructions Product Description This installation
More informationPowermite 599 MT Series SQS Electronic Valve Actuator, 24 Vac, Floating Control (3-position)
Powermite 599 MT Series SQS Electronic Valve Actuator, 24 Vac, Floating Control (3-position) Document No. 155-308P25 EA 599-14 Description Features Application The Powermite 599 MT Series SQS85.53U Electronic
More informationSQM5 Reversing Actuator with Analog Input Signal
Document o. 129-4 January 18, 28 SQ5 Reversing Actuator with Analog Input Signal Product Description Reversing actuator used to position flow control valves, butterfly valves, dampers, or any application
More informationPowers Controls No. 6 Pneumatic Damper Actuator
Document No. 152-013P25 Powers Controls No. 6 Pneumatic Damper Actuator OEM Literature Basic Actuator Typical Actuator with Clevis and Pin Actuator with Extended Shaft and Frame Mounting Accessories Description
More informationSAX Electronic Valve Actuator
SAX Electronic Valve Actuator Non-spring Return, 24 Vac, Proportional Control Technical Instructions Document No. 155-506 Description The SAX Non-spring Return (NSR), Electronic Valve Actuator requires
More informationTechnical Instructions Document No P25 EA GMA January 19, OpenAir. GMA Series Spring Return Rotary Electronic Damper Actuators
OpenAir GMA Series Spring Return Rotary Electronic Damper Actuators Document No. 155-315P25 EA GMA Description Features Application The OpenAir direct-coupled spring return electronic actuator is designed
More informationFlowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features
Flowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features Technical Instructions Document No. 155-717 EA-599-18 SKB/C SKD Description The Flowrite
More informationTechnical Instructions Flowrite 599 Series SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Description Features Application
Document No. 155-180P25 Flowrite 599 Series SKD6xU Electronic Valve Actuators 24 Vac Proportional Control Description The Flowrite 599 Series SKD6xU Electronic Valve Actuators require a 24 Vac supply and
More informationOpenAir GCA Series Spring Return 142 lb-in Electronic Damper Actuators
OpenAir GCA Series Spring Return 4 lb-in Electronic Damper Actuators EA GCA- Description The OpenAir 4 Vac/dc spring return 4 lb-in electronic actuator is designed for digital or analog control of building
More informationHeat Pump Controller Multi-Stage
Install llation Instruction ons Document No. 540-204 Rev. 2, January, 1999 Heat Pump Coller Multi-Stage Produ oduct Description These instructions explain how to field install (pages 1 and 2) or replace
More informationFlowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features
Flowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features Technical Instructions Document No. 155-717 EA-599-18 SKB/C SKD Description The Flowrite
More informationDodge Engineering & Controls, Inc. Toll Free (877) Fax: (978) ES142 Spring Return Electronic Actuators
a EA0655R1 c b e f g d h a. Actuator b. Shaft adapter c. Position indicator d. Shaft adapter locking clip e. Position indicator adapter f. Mounting bracket (for dampers) g. Mounting screws h. 3 mm hex
More informationM Remote Mounting Kit
M9203-250 Remote Mounting Kit Installation Instructions M9203-250 Part No. 34-636-2324, Rev. Issued July 6, 2011 Applications The M9203-250 Remote Mounting Kit enables the M9203 Series Electric Spring
More informationSAV Electronic Valve Actuator
Document No. 155-548 Non-spring Return, 24 Vac/dc, 3-Position Control Description The SAV Non-spring Return (NSR), Electronic Valve Actuator requires a 24 Vac/dc supply to provide three-position (floating)
More information599 Series Ball Valve and Actuator Assemblies Selection
599 Series Ball and Actuator Assemblies Selection Technical Bulletin Document No. 155-704P5 TB 53 Description Example: Selecting a -Way Ball and Actuator for -Position Control This Technical Bulletin aids
More information599 Series Ball Valve and Actuator Assemblies Selection
599 Series Ball and Actuator Assemblies Selection Technical Bulletin Document No. 155-704P25 TB 253 Description This Technical Bulletin aids in the selection of a ball valve and actuator assembly. Table
More informationFlowrite EA 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control
Flowrite EA 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control Document No. 155-171P25 EA 599-2 Description The Flowrite EA 599 Series SKB/C electronic valve actuator requires
More informationRDG160TU Commercial Thermostat
Document No. 129-588 RDG160TU Commercial Thermostat Selecting Location Install the thermostat about 4 feet (120 cm) above the floor on an inside wall. Ensure that there is free airflow around the thermostat.
More informationFlowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac Proportional Control
Flowrite EA 599 Series SKD Electronic Valve Actuator 24 Vac Proportional Control Document No. 55-8P25 EA 599-4 EA379R Description The Flowrite EA 599 Series SKD Electronic Valve Actuator requires a 24
More informationAccessories/Kits Ball Valve Bracket Kit (includes bracket, mounting screws, shaft and handle)
599 Series Technical Instructions Document No. 155-703P25 VF 599-9 2-Way Ball s Description The 599 Series 2-way Ball s are coupled with OpenAir actuators to provide equal percentage flow control. The
More information599 Series 2-Way Ball Valves
599 Series 2-Way Ball s Technical Instructions Document No. 155-703P25 VF 599-9 Description The 599 Series 2-way Ball s are coupled with OpenAir actuators to provide equal percentage flow control. The
More informationFlowrite 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control
Document No. 155-171P25 Flowrite 599 Series SKB/C Electronic Valve Actuator 24 Vac, 3-Position (Floating) Control 8Description The Flowrite 599 Series SKB/C electronic valve actuator requires a 24 Vac
More informationVE VVG Series Electronic Two-way Valves Normally Closed
VE VVG Series Electronic Two-way s Normally Closed Document No. 155-112P25 VE VVG-1 Description The VE VVG electronic two-way valves control the flow of water or glycol solutions. The electronic actuator
More informationPowers TM Controls SW 141 Differential Static Airflow Switches
Powers TM Controls SW 141 Differential Static Airflow Switches Document No. 155-052P25 SW 1 0518 Description The SW 141 Airflow Switch senses static differential pressure and the diaphragm operated snap
More informationD-70, D-140, D-210, and D-280 Series Electric Non-Spring Return Actuators
Installation D-70, D-140, D-210, and D-280 Series Electric Non-Spring Return Actuators IMPORTANT: The D- Series actuators are intended to control equipment under normal operating conditions. Where failure
More informationSwitch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches
Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools Required: Personal Protective
More informationPowermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Floating Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Floating Control Document No. 155-314P25 EA 599-16 Description Features Application Product Numbers The Powermite 599 MT Series SSC81U and
More informationOpenAir. Technical Instructions. GCA Series Spring Return 160 lb-in Electronic Damper Actuators. Document No P25 EA GCA-1.
OpenAir GCA Series Spring Return 160 lb-in Electronic Damper Actuators EA GCA-1 Description The OpenAir 24 Vac/dc spring return 160 lb-in (18 Nm) electronic actuator is designed for digital or analog control
More informationSwitch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches
Step Switch Base Replacement Instructions 3-Pole, 60 AMP, Fusible, w Neutral, Visible-Blade, Heavy Duty Safety Switches Work Description All work should be performed in accordance with NFPA 70E. Tools
More informationD24-53 Series Electric Non-Spring Return Actuators 53 lb in Models (6 N m)
Installation Instructions D24-53 Issue Date November 4, 23 D24-53 Series Electric Non-Spring Return Actuators 53 lb in Models (6 N m) Installation IMPORTANT: The D24-53 Series actuator is intended to control
More informationDuraDrive MF /MS Series Non-spring Return Rotary Electronic Damper Actuators 24 Vac Three-position/Modulating
General Instructions DuraDrive MF4-653/MS4-653 Series Non-spring Return Rotary Electronic Damper Actuators 4 Vac Three-position/Modulating Description The DuraDrive direct-coupled, 4 Vac, non-spring return
More informationSCC Inc. BRx Series. Technical Instructions. Document No. CPBK-2000 September 15, BR-AS Bracket Assemblies for use with SQM Actuators
SCC Inc. BRx Series BR-AS Bracket Assemblies for use with SQM Actuators Technical Instructions September 15, 2015 Description Features Application BRx series bracket assemblies installed with Cxx series
More informationFlowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features
Flowrite EA 599 Series SKB/C/D 62UA Series Electronic Valve Actuator 24 Vac Proportional Control Advanced Features Technical Instructions Document No. 55-77 EA-599-8 April 3, 24 EA228R EA379R SKB/C SKD
More informationPowers Controls No. 4 Pneumatic Damper Actuator
Document No. 152-012P25 Powers Controls No. 4 Pneumatic Damper Actuator OEM Literature Pivot Mount Actuator with Clevis, Clevis Pin, and Hitch Pin Clip Actuator with Fixed Bracket Mounted Actuator with
More information599 Series 2-Way Ball Valves
599 Series 2-Way Ball s Description The 599 Series 2-way Ball s are coupled with OpenAir actuats to provide equal percentage flow control. The Ball s are 1/4-turn rotary control valves. Numbers Use the
More information599 Series 2-Way Ball Valves
599 Series 2-Way Ball s Description The 599 Series 2-Way Ball s are coupled with OpenAir actuats to provide equal percentage flow control. The Ball s are 1/4-turn rotary control valves. Numbers Use the
More informationS Voltage Regulators PRODUCT INFORMATION GENERAL. Contents. Acceptance and Initial Inspection. Handling and Storage
Voltage Regulators QD3T350 Reversing Stationary Contact Assembly Instructions Kit 5791822A02 Service Information S225-50-43 Contents General..................................... 1 Parts Supplied...............................
More informationPressure Independent Control Series
Pressure Independent Control Series Two-Way, Brass Valve Bodies, -Inch to 2-Inch, ANSI 250 to 1-1/4 Inch NC - to 1-1/4-Inch NO 1- to2-inch NO Description Features Application Product Numbers and Ordering
More informationS Voltage Regulators PRODUCT INFORMATION GENERAL. Contents. Acceptance and Initial Inspection. Handling and Storage.
Voltage Regulators QD3/T350 Main Movable Contact Assembly Kit Kit 5741325B04 Service Information S225-50-42 Contents General..................................... 1 Tools Required..............................
More informationPowermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control Technical Instructions Document No. 155-313P25 EA 599-15 EA1157R1 Description The Powermite 599 MT SSC61U and SSC61.5U
More informationTechnical Instructions. SQV Series Electromotive Valve Actuators. Document No
Document No. 155-521 (For Use with 2-1/2-Inch to 6-Inch Pressure Independent Control Valves) Features Operating voltage: AC/DC 24V Application Control signals: 3-position, DC 0 to 10V, DC 4 to 20 ma Fail-safe
More informationM9216 Series Electric Spring Return Actuators
*34636461G* 34-636-461, Rev. J Installation Instructions M9216 Issue Date October 217 M9216 Series Electric Spring Return Actuators Installation IMPORTANT: The M9216 Series actuator is intended to control
More informationPowermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control
Powermite 599 MT Series SSC Electronic Valve Actuator, 24 Vac Proportional Control Document No. 155-313P25 EA 599-15 Description The Powermite 599 MT SSC61U and SSC61.5U series of electronic valve actuators
More information599 Series 2-Way Ball Valves
Description The are coupled with OpenAir actuats to provide equal percentage flow control. The Ball s are 1/4-turn rotary control valves. Numbers Use the product numbers in Table 1 through Table 9 to der
More informationPressure Independent Control Series
Pressure Independent Control Series Two-Way, Brass Valve Bodies, 1/2-Inch to 2-Inch, ANSI 250 1/2 to 1-1/4 Inch NC 1/2- to 1-1/4-Inch NO 1-1/2 to2-inch NO Description Features Application Product Numbers
More informationEDA-8100 Electric Damper Actuator
Installation Sheet Issue Date 0392 EDA-8100 Electric Damper Actuator Kit Includes 1. EDA-8100-1100 Electric Damper Actuator with counterclockwise spring return, or EDA-8100-1101 Electric Damper Actuator
More informationPowermite 599 MT Series Terminal Unit Valve and Actuator Assembly Selection
Document No. 155-306P25 TB 251 Powermite 599 MT Series Terminal Unit and Actuator Selection Description This Technical Bulletin aids in selecting a Powermite 599 Series MT Series terminal unit valve and
More information