Parts & Service. Terreon Multi-Fount Washfountain Current Models After February 1, MF2922 Corner-Fount. MF2933 Tri-Fount

Transcription

1 MF9 (AST shown) MF9 (AST shown) Parts & Service Terreon Multi-Fount Washfountain Current Models After February, 0 MF9 Corner-Fount MF9 Tri-Fount MF99 Tri-Fount, Wall-Hung MF9 Quadra-Fount MF99 Quadra-Fount, Wall-Hung MF99 (AST shown) Table of Contents Infrared (IR)... Air Metering (AST)... AST and IR Supply and Mixing Valve... 0 Battery Infrared (BIR)... TouchTime (TT)... Thermostatic Mixing Valve Troubleshooting... Soap System... 9 Drain Spud and Strainer... Floor Pedestal Assembly... Wall Mount Pedestal Assembly... Sprayhead Covers... Pedestal Panels... Bowl Assembly... Terreon Cleaning and Maintenance... MF9 (AST shown) Part numbers are subject to change without formal notice. MF99 (AST shown) - Rev. J; ECN Bradley Page of 9//0 P.O. Box 09 Menomonee Falls, WI 0 USA 00 BRADLEY (00 9) bradleycorp.com

2 Terreon Multi-Fount Washfountains Parts and Service Infrared (IR) Sprayhead (V Plug-In Transformer) 0 9 Parts List Infrared Sensor and Sprayhead Assembly Corner Tri Quad Qty. Qty. Qty. 9-0 Sensor - Adaptive - P0-9 Hook and Loop Fastener Strip (sensor mounting) 9-90 Window - Sprayhead -9 Threaded Rod 0- Backplate -0 Nut -00BS Lockwasher 9- Fitting Straight (front sprayhead) Fitting Swivel 90 (side sprayheads) 0 R-00-R Tubing /", Red * * * 0 R-000-G Tubing /", Green * * * 0 R-000-B Tubing /", Black * * * 0 R-000-Y Tubing /", Yellow * * * * Specify length in feet 9//0 Bradley - Rev. J; ECN -00-0

3 Parts and Service Terreon Multi-Fount Washfountains Infrared (IR) Valves (V Plug-In Transformer) Red Supply Tube (From Sprayhead) Red Spade Terminal Green Supply Tube (From Sprayhead) Black Supply Tube (From Sprayhead) White Jumper Terminals Green Spade Terminal 9 0 Black Spade Terminal White Spade Terminal Tri-Fount Shown Parts List Solenoid Valve Assembly and Valve Parts Corner Tri Quad Qty. Qty. Qty. S-9 IR TMA Dual valve Assembly (includes items -) - - S-9 IR TL Dual Valve Assembly (includes items -) - - S-9 IR TMA Tri Valve Assembly (includes items -) - - S-9 IR TL Tri Valve Assembly (includes items -) - - S- IR TMA Quad Valve Assembly (includes items -) - - S- IR TL Quad Valve Assembly (includes items -) - - S0- Navigator Valve, GP 0-9 Bracket, Ganged Valve 9 P-0 Screw 0- x / PN 0 S0-0A Solenoid Valve, VAC, through S0-0 Solenoid Valve, VAC, closed 0- Compression Nut, /" 0- Screw - x / PN S9-0 Adapter, Valve Inlet S- Transformer Bradley - Rev. J; ECN //0

4 Terreon Multi-Fount Washfountains Parts and Service Infrared (IR) Valve Assembly - Solenoid Valve S0-0S (Closed Body) and S0-0AS (Thru Body) Solenoid Valve Parts List Qty -0 Valve Body, /" Closed -0A Valve Body, /", Through 9-9 Diaphragm 9- Armature 9- Spring 9-9 Armature Housing 9-0 clamp, Armature Housing 9-9 Coil, Solenoid Valve 0- Screw # x / 9 - O-Ring, # Flow Restrictor, 0. GPM S- Repair Kit 0 9 Turn off water supplies to unit before troubleshooting. Problem Cause Solution An individual operating station fails to shut off and drips. An individual operating station fails to turn on. There is debris trapped between the diaphragm and the valve seat. A failed coil for the valve or loose electrical connection to the terminal. Remove debris between diaphragm and the valve seat.. Remove the three # Phillips-head screws that hold the solenoid valve assembly together. Be careful not to lose the armature or spring (see previous page).. Remove the diaphragm. Remove any particles that have been trapped between the diaphragm and the valve seat. Rinse off the diaphragm and inspect for damage. Make sure the center orifice and both small side orifices are open.. Reassemble in reverse order, being careful not to overtighten the Phillips-head screws or you may crack the plastic valve body. Tighten until the armature plate makes contact with the plastic body.. Reconnect the wiring per diagram. Test the station to determine cause.. Disconnect the wires from the coil of an adjacent valve. Disconnect the wires from the problem valve and reconnect to the adjacent valve.. Turn on electrical and water supplies to the unit. Place hands in front of sensor for the problem station; the adjacent station should turn on. If the adjacent station turns on and cycles normally, replace the coil on the problem valve. If the adjacent valve fails to turn on, inspect the wires from the sensor cable and do the following: make sure there are no breaks and that the fully insulated disconnect terminals are firmly crimped in place; turn off the electrical and water supplies; reconnect to the adjacent valve and turn on the water supplies to the unit; place hands in front of sensor. If the station still fails to turn on, replace the sensor. 9//0 Bradley - Rev. J; ECN -00-0

5 Parts and Service Terreon Multi-Fount Washfountains Air Metering Valve (AST) - Pushbutton and Sprayhead Bradley - Rev. J; ECN //0

6 Terreon Multi-Fount Washfountains Parts and Service Parts List AST Pushbutton and Sprayhead Corner Tri Quad Qty. Qty. Qty. S0-0 Pushbutton Assembly (Includes Items thru ) -090 Pushbutton Only 9-0 Guide for Pushbutton -0 Shoulder Screw for Pushbutton -0 Spacer 0- Brackey 0- Nut - S- Actuator Assembly (Includes Items 9 thru ) - S-A Actuator Assembly (Includes Items 9 thru ) A Piston U-Cup -0 Spring -9 Actuator Body 9-00 Duckbill Check 9-90 Tube Connector /" Straight 9- Fitting Adj J - 0- Screw R-0000-R Tubing /" OD, Red * * * R-0000-G Tubing /" OD, Green * * * R-0000-B Tubing /" OD, Black * * * R-0000-Y Tubing /" OD, Yellow * * * - Sprayhead 9-9 Threaded Rod Window Hole Plug 0- Backplate -0 Nut -00BS Lockwasher 9- Fitting Straight (Front Sprayhead) - 9- Fitting Swivel 90 (Side Sprayheads) R-000-R Tubing /" ID, Red * * * R-000-G Tubing /" ID, Green * * * R-000-B Tubing /" ID, Black * * * R-000-Y Tubing /" ID, Yellow * * * 0-0 Spanner Wrench * Specify length in feet. 9//0 Bradley - Rev. J; ECN -00-0

7 Parts and Service Terreon Multi-Fount Washfountains Air Metering Valve (AST) - Assembly 0 9 Parts List Air Metering Valve Assembly Corner Tri Quad Qty. Qty. Qty. S0-TMA TMA Dual Valve Assembly (Includes Items thru ) - - S0-TL TL Dual Valve Assembly (Includes Items thru ) - - S0-TMA TMA Tri Valve Assembly (Includes Items thru ) - - S0-TL TL Tri Valve Assembly (Includes Items thru ) - - S0-TMA TMA Quad Valve Assembly (Includes Items thru ) - - S0-TL TL Quad Valve Assembly (Includes Items thru ) - - S0- Navigator Valve, GP 0-9 Bracket, Ganged Valve 9 P-0 Screw 0- x / PN 0 S0-0AS AST Valve, Through S0-0S AST Valve, Closed 0- Compression Nut, /" 0- Screw - x / PN S9-0 Adapter, Valve Inlet Bradley - Rev. J; ECN //0

8 Terreon Multi-Fount Washfountains Parts and Service AST Valve Repair Kits 9 0 Parts List AST Valve Repair Kits - O-Ring -0A Valve Body - Manifolded -0 Valve Body - Closed 9-9 Diaphragm 9- Armature, Valve 9- Spring, Valve -09 Cover, AST Valve 0- Cover, AST Valve Timer 9 S-0 Timer, ASM, AST Valve 0-00BY O-Ring 0- Compression Nut, /" S9-9 Magnet/Diaphragm Assembly 0- Cover, AST Valve 0- Clamp Nut, AST Valve 0-9 Screw - x /" S- Repair Kit - AST Valve - Upper S- Repair Kit - AST Valve - Lower S-0 Repair Kit - AST Valve - Complete 9//0 Bradley - Rev. J; ECN -00-0

9 Parts and Service Terreon Multi-Fount Washfountains Metering Air Valve Maintenance and Troubleshooting The air valve timer is located next to the tube connector on the air valve body. The timer is capped with a filter to prevent dirt build-up on the timer. The air valve timing can be adjusted from 0 seconds. Water Tube Connector Air Valve Manual Release Button Air Valve Tubing Locking Slope Filter Cap Air Tube Connector Sealing Ring Gripping Ridge Tube Stop Problem Cause Solution Air valve meter time needs adjusting. Adjust air valve meter time:. Remove filter cap and use a screwdriver to tighten or loosen the timer (see illustration above). Turning the timer clockwise increases the time; turning the timer counterclockwise decreases the time. Valve will not shut off. Valve will not turn on. Timing can not be adjusted for more than seconds. Push button does not work properly. Water is dripping from the streamformers. Timing mechanism is clogged. Water is not being supplied to unit. Water pressure is over 0 PSI. Failed diaphragm/ magnet assembly. There is an air leak. Air volume may not be sufficient to operate valve. Debris has accumulated on valve seat or orifices.. Continue to adjust until the timer is set at desired length.. Replace filter cap over the timer. Clean and inspect timing mechanism:. If compressed air is available, blow water and debris from timer cover of timing mechanism.. Turn adjusting screw out all the way. Clean and inspect screw and valve body.. Turn adjusting screw in to desired cycle time. Open all stops on mixing valve. Install a pressure reducing valve. Unscrew the valve clamp nut on valve. Remove valve cover. Gently press the diaphragm. The valve should activate. If not, replace the diaphragm/magnet assembly. Check the valve assembly:. Check all tubing and fittings for proper assembly.. Tighten cap and nut on /" tubing. Check for leaks and lubricate U cup:. Check all fittings for air leaks.. Disassemble push button and lubricate U cup seal. Clean and inspect valve seat.. Remove screws and disassemble metering valve.. Clean valve seat and inspect for deep gouges or scratches. Replace valve body if necessary.. Remove any debris clogging off center hole in rubber diaphragm. Bradley - Rev. J; ECN //0 9

10 Terreon Multi-Fount Washfountains Parts and Service AST and IR Supply and Mixing Valve - Floor and Wall Mounted Air Valve Assembly Hot Supply Inlet Navigator TMV Cold Supply Inlet Floor Mount (Tri-Fount Shown) Hot Supply Inlet Cold Supply Inlet Air Valve Assembly Navigator TMV Wall Mount (Quadra-Fount Shown) Supply Parts List Corner Tri Quad Qty Qty Qty * 9-0 Flex Hose (Supply to TMV) * S-0 Stop 0-9 Screw * Use Qty for TL option, all models. 0 9//0 Bradley - Rev. J; ECN -00-0

11 Parts and Service Terreon Multi-Fount Washfountains Battery Infrared (BIR) - Sprayhead 0 9 Parts List - Battery Infrared Sensor and Sprayhead Corner Tri Quad Qty Qty Qty -09A Sensor Eye Leads 9-90 Window - Sprayhead -9 Threaded Rod 0- Backplate -0 Nut -00BS Lockwasher 9- Fitting Straight (front sprayhead) Fitting Swivel 90 (side sprayheads) 0 R-000-R Tubing /", Red * * * 0 R-000-G Tubing /", Green * * * 0 R-000-B Tubing /", Black * * * 0 R-000-Y Tubing /", Yellow * * * * Specify length in feet. Bradley - Rev. J; ECN //0

12 Terreon Multi-Fount Washfountains Parts and Service Battery Infrared Valve (BIR) - Assembly 9 0 Tri-Fount Shown 9 Parts List - Battery Infrared Valve Assembly Corner Tri Quad Qty Qty Qty S0-TMA TMA Dual Valve Assembly (includes items -) - - S0-TL TL Fual Valve Assembly (includes items -) - - S0-TMA TMA Tri Valve Assembly (includes items -) - - S0-TL TL Tri Valve Assembly (includes items -) - - S0-TMA TMA Quad Valve Assembly (includes items -) - - S0-TL TL Quad Valve Assembly (includes items -) - - S0- Navigator Valve, GP 0-9 Bracket, Ganged Valve 9 P-0 Screw 0- x / PN 0 S0-0AS BIR Valve, through (includes items -) S0-0S BIR Valve, closed (includes -) 0- Compression Nut, /" 0- Screw - x /" PN S9-0 Adapter, Valve Inlet S- Circuit Board 0- Screw #-9 x / S- Battery Holder 9-00 Lithium Battery, Type DLA or Equivalent 0 S-0 Battery Prepack (includes items -9) 9//0 Bradley - Rev. J; ECN -00-0

13 Parts and Service Terreon Multi-Fount Washfountains Battery Infrared Valve (BIR) Assembly - Solenoid Valve S0-0S (Closed Body) and S0-0AS (Thru Body) Item Qty Part No. Description -0 Valve Body, /" Closed -0A Valve Body, /" Thru 9-9 Diaphragm 9-0 Armature -09 Spring 9-9 Armature Housing 9-0 Clamp, Armature Housing 9- Coil, Solenoid Valve 0- SCrew, # x /" 9 - O-Ring, # Flow Restrictor,. GPM Solenoid Valve with Circuit Board Closed Body (S0-0S) Thru Body (S0-0AS) Circuit Board (S-) 0 Pan-Head Screw -9 x /" (0-) Bradley - Rev. J; ECN //0

14 Terreon Multi-Fount Washfountains Parts and Service Troubleshooting BIR Components CAUTION: Turn off water supplies to unit before troubleshooting. Problem: Cause: An individual operating station drips and fails to shut off. There is debris trapped between the diaphragm and the valve seat. Solution: Remove debris between diaphragm and the valve seat. Disconnect the plug from the battery to the circuit board of the problem valve. Remove the three # Phillips-head screws that hold the solenoid valve assembly together. Be careful not to lose the armature or spring. Remove the diaphragm. Remove any particles that are trapped between the diaphragm and the valve seat. Rinse off the diaphragm and inspect for damage. Make sure the center orifice and both small side orifices are open. Reassemble in reverse order, being careful not to overtighten the Phillips-head screws or you may crack the plastic valve body. Tighten until the armature plate makes contact with the plastic body. Reconnect the battery plug. Turn on water supplies to the unit. Problem: Cause: Solution: An individual operating station fails to turn on or off. Excessive line pressure. Install pressure reducing valve. Check the static line pressure. If the pressure exceeds 0 psi, install a pressure reducer valve at the street main. Excessive line pressure (over 0 psi) will shorten the life of any valve. Problem: Cause: Solution: An individual operating station fails to turn on or off. A dead or faulty battery. Test the station to determine cause and replace battery if required. Disconnect the plug from the battery to the circuit board of the problem valve. Disconnect the plug from the battery to the circuit board of an adjacent valve. Connect the battery plug from the adjacent working valve to the problem valve. Wait for ten seconds. Activate the problem station s sensor ten times. The station should turn on. If the station turns on, and cycles normally, replace the battery. Cause: Solution: Faulty sensor eyes. Test station to determine cause; replace sensor eyes if required. Disconnect the sensor cable from the circuit board of the problem valve. Disconnect the sensor cable from the circuit board of an adjacent working valve. Connect the sensor cable from the adjacent working valve to the problem valve. Activate the problem station s sensor. The station should turn on. If the station turns on and cycles normally, replace the sensor eyes. OPEN VALVE Cause: Solution: Faulty solenoid valve. Test station to determine cause; replace solenoid valve if required. Remove the screw, circuit board and standoff from the problem valve. Remove the battery holder. With a good working battery, briefly contact the solenoid valve directly with the battery as shown in Open Valve figure to right. The contact should cause the valve to open. With the battery holder removed, briefly contact the solenoid valve with the battery in the position shown in Closed Valve figure to right. This should cause the valve to close. If the valve does not operate when directly contacted with a good battery, and the solenoid valve has already been cleaned as outlined at the beginning of this troubleshooting section, replace the solenoid valve. If problems persist: Pass your hand in front of the problem station, while at the same time looking to see if the indicator light on the circuit board flashes (the indicator light is located near the hole in the circuit board where the standoff is mounted). If it does not flash, and the battery and sensor eyes have already been tested as outlined above, the problem may be with the circuit board. Make a note of the numbers printed on the circuit board, then contact your Bradley representative for assistance. CLOSED VALVE 9//0 Bradley - Rev. J; ECN -00-0

15 Parts and Service Terreon Multi-Fount Washfountains TouchTime (TT) - Sprayhead (V Plug-In Transformer) 0 9 Parts List - TouchTime (Switch and Sprayhead) Corner Tri Quad Qty Qty Qty S-9B Switch TouchTime 9-90 Window - Sprayhead -9 Threaded Rod 0- Backplate -0 Nut -00BS Lockwasher 9- Fitting Straight (front sprayhead) Fitting Swivel 90 (side sprayheads) 0 R-000-R Tubing /", Red * * * 0 R-000-G Tubing /", Green * * * 0 R-000-B Tubing /", Black * * * 0 R-000-Y Tubing /", Yellow * * * - Spacer 0- Nut, /- 0-0 Spanner Wrench * Specify length in feet. Bradley - Rev. J; ECN //0

16 Terreon Multi-Fount Washfountains Parts and Service TouchTime (TT) Metering Valve - Assembly Black Supply Tube (From Sprayhead) Green Supply Tube (From Sprayhead) 9 0 Red Supply Tube (From Sprayhead) Gray Wires Terminal Block Brown Wires Supply Inlet Black Wires Green Wires Left Button Center Button Right Button Parts List - TouchTime Metering Valve Assembly Corner Tri Quad Qty Qty Qty S-9 TT TMA Dual Valve Assembly (Transformer not Included) - - S-9 TT TL Dual Valve Assembly (Transformer not Included) - - S-9 TT TMA Tri Valve Assembly (Transformer not Included) - - S-99 TT TL Tri Valve Assembly (Transformer not Included) - - S-9 TT TMA Quad Valve Assembly (Transformer not Included) - - S-0 TT TL Quad Valve Assembly (Transformer not Included) - - S0- Navigator Valve, GP 0-9 Bracket, Ganged Valve 9 P-0 Screw 0- x / PN 0 S0-0A Solenoid Valve, VAC, through S0-0 Solenoid Valve, VAC, closed 0- Compression Nut, /" 0- Screw - x / PN S9-0 Adapter, Valve Inlet S- Transformer 9//0 Bradley - Rev. J; ECN -00-0

17 Parts and Service Terreon Multi-Fount Washfountains TouchTime Valve (TT) Assembly - Solenoid Valve S0-0S (closed body) and S0-0AS (thru body) Item Qty. Part No. Description -0 Valve Body, ¼" Closed -0A Valve Body, ¼" Thru 9-9 Diaphragm 9- Armature 9- Spring 9-9 Armature Housing 9-0 Clamp, Armature Housing 9-9 Coil, Solenoid Valve 0- Screw, # x / 9-00CS O-Ring, # Flow Restrictor,. GPM S- Repair Kit 0 9 Problem Cause Solution An individual operating station fails to shut off and drips. Debris is trapped between the diaphragm and the valve seat. Remove debris between diaphragm and the valve seat.. Remove the three # Phillips-head screws that hold the solenoid valve assembly together. Be careful not to lose the armature or spring.. Remove the diaphragm. Remove any particles that have been trapped between the diaphragm and the valve seat. Rinse off the diaphragm and inspect for damage. Make sure the center orifice and both small side orifices are open.. Reassemble in reverse order (do not overtighten the Phillips-head screws or the plastic valve body may crack). Tighten until the armature plate makes contact with the plastic body.. Reconnect the wiring. An individual operating station fails to turn on. A failed coil for the valve or loose electrical connection to the terminal. Test the station to determine the cause.. Disconnect the wires from the coil of an adjacent valve. Disconnect the wires from the problem valve and reconnect to the adjacent valve.. Turn on electrical and water supplies to the unit. Pass your hand in front of the sensor of the problem station, and the adjacent station should turn on. If the adjacent station turns on and cycles normally, replace the coil on the problem valve. If the adjacent valve fails to turn on, inspect the wires from the sensor cable and do the following: make sure there are no breaks and that the fully insulated disconnect terminals are firmly crimped in place; turn off the electrical and water supplies; reconnect to the adjacent valve and turn on the water supplies to the unit; pass your hand in front of the sensor. If the station still fails to turn on, replace the sensor. Bradley - Rev. J; ECN //0

18 Terreon Multi-Fount Washfountains Parts and Service Thermostatic Mixing Valve Troubleshooting Before attempting to troubleshoot the valve or disassemble the components, check for the following conditions: If stop valves are used, make sure that they are fully open. Make sure that the hot and cold inlet pipes are connected properly, and that there are no cross-connections or leaking stop valves. Check the hot water heater output to make sure that it is at least 0 F above the set temperature. Problem Cause Solution External leaks. Damaged cartridge or O-rings. Replace cartridge with part number 9-9 Improper water temperature or temperature fluctuation. Be sure to close the appropriate shut-off valves prior to disassembly of the valve and reopen the valves after inspection and repair is complete. Hot water supply is not 0 above desired set point. Valve temperature is not properly set. Increase hot water supply temperature Adjust the temperature.. Loosen the cap screw about /" (- turns) and lift up the cover (do not remove).. Using the cover, turn the cartridge gently until desired water temperature is reached. Do not turn past stops as this may damage the unit. Push the cover down and tighten the screw. Limited water flow. Dirt and debris have built up in the valve or strainer.. Check to make sure both hot and cold supplies are connected to the Navigator mixing valve and that they have water flow.. Remove cover and U-clip. Remove the cartridge and clean the strainer. It is not required to grease cartridge, however if desired, use silicone grease only. Do not use grease on check valves. Parts List Quantity S Cap Screw 0- Cover 9-9 Thermostatic Cartridge 9-0 Check Valve* -0 Retaining Ring* -9 Valve Body -09 U-Clip * Included with Prepack S- Tempered Line Adapter Option Part no. S9-0 (replaces S9-000 if tempered line is used) Strainer (-0) 9//0 Bradley - Rev. J; ECN -00-0

19 Parts and Service Terreon Multi-Fount Washfountains Soap System Parts List - Soap Valve S09-0 Qty S09-0 Soap Valve Complete S-09 Plunger Assembly 0-A Collar 0-9 Set Screw - O-Ring 9-0 Seat Assembly -09 Spring -0M Cylinder R-0000 Tube /" ID (Specify Length in Feet) Qty 0-00 Soap Tank 9-99 Hose / ID * -00 Hose Clamp 9-9 Male Fitting 0-09 Nut 0-00CJ Washer - Filler -0 Soap Filler Cap 9 R-00 Tube Vent / * 0-09 Soap Tank Cap 9- Bulkhead Fitting R-0000 Tube Supply / * 9- Tee 0- Nut -00CB Washer S-09 Soap Valve Body Assembly S09-0 Soap Valve 0- Soap Filler Cap Wrench 9-0 Nut 0-00AV Washer 9- Ferrule R-000 Tube * S0-09 Complete Soap System (incl. items -) Bradley - Rev. J; ECN //0 9

20 Terreon Multi-Fount Washfountains Parts and Service Soap System Soap Recommendations Quality soap dispensers require good quality soap and periodic maintenance to properly operate. Bradley soap dispensers will provide dependable, consistent operation over the long term when soap with reasonable viscosity and ph levels are used and when a minimal amount of periodic maintenance is performed on the valves. Soap thickness is determined by a measurement called viscosity. Soap viscosity should be between 00 cps (centerpoise) and 00 cps for all Bradley soap dispensers. Thinner soaps are perceived by the users as being "watered down" so users tend to take more than they need, resulting in waste. Thick soaps flow slower and inhibit the "flushing" action of the valves, which allows the soap to congeal in the valve and cause clogs. The ph (acid) level of the soap should be in the range of. to.. More acidic soaps (ph levels lower than.) will corrode metal parts (even stainless steel!!) and degrade rubber and plastic components. They will also cause skin irritation. Most inexpensive soaps (typically the pink lotion type) fall into this acidic category and will eventually cause valve failure and metal corrosion. Base soaps (ph levels higher than.) will cause swelling or degradation of rubber and plastic parts and skin irritation. Generally, any quality soap meeting the viscosity and ph guidelines above will work well with Bradley soap dispensers. PCMX or Isapropanol based antibacterial soaps (within viscosity and ph limits) will also work with Bradley dispensers. Soaps satisfying these basic guidelines will provide consistent flow and reduce clogs. Most soap dispenser problems are caused by soap that is too thick or corrosive, or by a lack of maintenance. Many soaps come in concentrate form which must be diluted with water. Often, the soap is improperly diluted or used straight out of the bottle, which causes clogging and valve failure. If proper soap is being used, valves that have never been cleaned are usually the source of dispensing problems. Bradley has entered into an agreement with Champion Brand Products to provide additional customer service for purchasers of our dispensers regarding soap issues. They are very helpful and can get to the bottom of almost any soap dispenser related problem. They also sell an excellent "Bradley approved" soap. Please see Soap Instruction Sheet - for details about soap valve cleaning or how to contact Champion. With proper maintenance and soap, Bradley dispensers will provide long term, trouble free operation. Soap Dispenser Maintenance Instructions for Multi-Fount Washfountains Bradley soap dispensers will provide dependable, consistent operation over the long term when the proper soap is used and when a minimal amount of periodic maintenance is performed on the valves. Valves must be maintained (cleaned) to function properly. To ensure proper operation of your soap dispenser, follow these instructions: Once per month, remove the cap from the soap tank and insert the draw tube (below the cap) into hot water and soak it for 0 minutes. Push valve at least 0 times while it is soaking. Flush soap reservoir with hot water while valve is soaking. In cases of extreme clogging, the valve should be disassembled and the parts should be soaked in hot water or cleaning solution to restore proper functioning. Soap dispensers that will not be used for extended periods of time (schools during summer break, etc.) should be drained, cleaned and left empty until put back into service. Soap left on the outside of dispensers can cause discoloration and corrosion of the reservoir (even on stainless steel units). All soap should be wiped or scrubbed off daily, then the outside of the dispenser should be rinsed with clear water and dried with a soft cloth. 0 9//0 Bradley - Rev. J; ECN -00-0

21 Parts and Service Terreon Multi-Fount Washfountains Drain Spud and Strainer Spud Washer (part of Item ) Washfountain Bowl Parts List Spud Locknut (part of Item ) Qty -0 Dome Strainer 0- Screw 0- x /" (for strainer) -09 Drain Spud (includes washer & nut) The rubber washer that comes with this kit is used for certain applications. Discard this washer for this application as it is not used on washfountains. Floor Pedestal - Assembly Corner Tri Quad Qty Qty Qty -9 Mounting Panel Mounting Panel - - ** S0-0 Upper Bracket Assembly - ** S0-0 Upper Bracket Assembly Lower Bracket Lower Bracket Screw /-0 x / -00BJ Washer -0 Clip S0-00 Access Panel - Standard Height - S0-09 Access Panel - Juvenile Height - S0-0 Access Panel - Standard Height - - S0-09 Access Panel - Juvenile Height - - * -0 Washer *9-09 Screw 9 * Access panel (Item ) part numbers include the screw and washer. ** Upper Bracket Assembly includes Item. Bradley - Rev. J; ECN //0

22 Terreon Multi-Fount Washfountains Parts and Service Wall Mount Pedestal - Assembly Corner Tri Quad Qty Qty Qty S- Pedestal Assembly - - S-0 Pedestal Assembly - - * 0-9 Screw /-0 - * P0- Screw 0- - * -0 C;o[ - S0-0 Access Panel - Standard Height - - ** -09 Screw - ** -0 Washer - * Pedestal assembly (item ) part numbers include the screws and clip ** Access panel (item ) part numbers include the screw and washer Sprayhead Cover Attaching Hardware Corner-Fount Tri-Fount Quadra-Fount Parts List - Sprayhead Cover Attaching Hardware Corner Tri Quad Qty Qty Qty 9- Anchor Bar Threaded Rod /-0 x " -0 Wing Nut /-0-90 Guide Tube Support Tube Anchor Bar - - 9//0 Bradley - Rev. J; ECN -00-0

23 Parts and Service Terreon Multi-Fount Washfountains Sprayhead Covers - Replacement Parts Parts Numbers - MF9 Corner Fount Color Covers Color Covers Arctic Chip S0-0AD Lannonstone S0-0S Bluesky S0-0AL Landon Gray S0-0AP Charcoal S0-0K Mountain Top S0-0AN Cobblestone Coffee Bean Cornfield S0-0T S0-0AJ S0-0AK Mystic Moss Organic Taupe Peppered White S0-0AG S0-0AR S0-0E Contact Bradley for bowl part numbers. Empire Gray S0-0 Graphite S0-0P Hillside S0-0AM Jade S0-0N Riverstone Stardust Summer Sage White Sand S0-0AF S0-0AH S0-0AE S0-0W Parts Numbers - MF9, MF99 Tri-Fount Color Covers Arctic Chip S0-0AD Bluesky S0-0AL Charcoal S0-0K Cobblestone S0-0T Coffee Bean S0-0AJ Cornfield S0-0AK Empire Gray S0-0 Graphite S0-0P Hillside S0-0AM Jade S0-0N Color Lannonstone Landon Gray Mountain Top Mystic Moss Organic Taupe Peppered White Riverstone Stardust Summer Sage White Sand Covers S0-0S S0-0AP S0-0AN S0-0AG S0-0AR S0-0E S0-0AF S0-0AH S0-0AE S0-0W Parts Numbers - MF9, MF99 Quadra-Fount Color Covers Arctic Chip S0-0AD Bluesky S0-0AL Charcoal S0-0K Cobblestone S0-0T Coffee Bean S0-0AJ Cornfield S0-0AK Empire Gray S0-0 Graphite S0-0P Hillside S0-0AM Jade S0-0N Color Lannonstone Landon Gray Mountain Top Mystic Moss Organic Taupe Peppered White Riverstone Stardust Summer Sage White Sand Covers S0-0S S0-0AP S0-0AN S0-0AG S0-0AR S0-0E S0-0AF S0-0AH S0-0AE S0-0W Bradley - Rev. J; ECN //0

24 Terreon Multi-Fount Washfountains Parts and Service Pedestal Panels Parts List - Sprayhead Cover Attaching Hardware Color Wall Mounted Left Panel Wall Mounted Right Panel Juvenile Height Left Panel Juvenile Height Right Panel Standard Height Left Panel Standard Height Right Panel Arctic Chip S-AD S-AD S-AD S-AD S-9AD S-0AD Bluesky S-AL S-AL S-AL S-AL S-9AL S-0AL Charcoal S-K S-K S-K S-K S-9K S-0K Cobblestone S-T S-T S-T S-T S-9T S-0T Coffee Bean S-AJ S-AJ S-AJ S-AJ S-9AJ S-0AJ Cornfield S-AK S-AK S-AK S-AK S-9AK S-0AK Empire Gray S- S- S- S- S-9 S-0 Graphite S-P S-P S-P S-P S-9P S-0P Hillside S-AM S-AM S-AM S-AM S-9AM S-0AM Jade S-N S-N S-N S-N S-9N S-0N Lannonstone S-S S-S S-S S-S S-9S S-0S London Gray S-AP S-AP S-AP S-AP S-9AP S-0AP Mountaintop S-AN S-AN S-AN S-AN S-9AN S-0AN Mystic Moss S-AG S-AG S-AG S-AG S-9AG S-0AG Organic Taupe S-AR S-AR S-AR S-AR S-9AR S-0AR Peppered White S-E S-AE S-E S-E S-9E S-0E Riverstone S-AF S-AF S-AF S-AF S-9AF S-0AF Stardust S-AH S-AH S-AH S-AH S-9AH S-0AH Summer Sage S-AE S-AE S-AE S-AE S-9AE S-0AE White Sand S-W S-W S-W S-W S-9W S-0W S- S- S-9 9//0 Bradley - Rev. J; ECN -00-0

25 Parts and Service Terreon Multi-Fount Washfountains Bowl - Assembly Parts List - Bowl Assembly Corner Tri Quad Qty Qty Qty 0-0 Bolt -00CG Washer 0-0 Bracket 00-0 Plate -00CH Lockwasher -0 Nut Bradley - Rev. J; ECN //0

26 Terreon Multi-Fount Washfountains Parts and Service Terreon Cleaning and Maintenance Material Description: Terreon is an NAHB Certified densified solid surface material composed of polyester resin and is resistant to chemicals, stains, burns and impact. Surface damage can be easily repaired with everyday cleansers or fine grit abrasives. Routine Cleaning: Clean daily or as often as conditions require using a standard commercial or household cleaner such as Formula 09 or Windex. Stubborn Stains: Remove tough stains with Ajax, Comet, or Soft-Scrub and a green Scotch-Brite pad or lightly sand in a circular motion with 0 grit wet/dry sandpaper. The finish can be renewed with a maroon Scotch-Brite pad. Special Situations for Material Scratches: Remove scratches with a green Scotch-Brite pad. The finish can then be renewed with a maroon Scotch-Brite pad. Hard Water Deposits: Remove hard water deposits with a mild solution of vinegar and water. Always rinse the unit thoroughly after cleaning. Restoring the surface: Use Hope s Solid Surface cleaner and polish to refresh and protect the Terreon Solid Surface material. Bradley recommends additional care and maintenance for the darker colored Terreon. For complete instructions on this additional maintenance see Bradley document #0. Do not use strong acid or alkaline chemicals and cleansers to clean Terreon. If these chemicals come in contact with the Terreon surface, wipe them off immediately and rinse with soapy water. Avoid contact with harsh chemicals such as paint remover, bleach, acetone, etc. Avoid contact with hot pans and objects. Repair Kits: Terreon repair kits are available. Contact your Bradley representative or distributor for part numbers and pricing. Repair kits are made to order and have a shelf life of 0 days. Brand Names: Use of brand names is intended only to indicate a type of cleaner. This does not constitute an endorsement, nor does the omission of any brand name cleaner imply its inadequacy. Many products named are regional in distribution, and can be found in local supermarkets, department and hardware stores, or through your cleaning service. It is emphasized that all products should be used in strict accordance with package instructions. When cleaning units equipped with infrared (electronic eye) activation, it is helpful to turn off the power to the unit or cover the windows to prevent accidental activation. After the window is covered, the water will run for approximately 0 seconds and then shut off. 9//0 Bradley - Rev. J; ECN -00-0