Geo Arch Single Lever Pull-Down Kitchen Faucet With Soap Dispenser

Transcription

1 INSTALLATION MANUAL Geo Arch Single Lever Pull-Down Kitchen Faucet With Soap Dispenser KPF I toll free: I Kraus USA Inc. I REV. August 16, 2016

2 Thank you for your purchase We would like to take this opportunity to thank you for choosing Kraus. We hope that you are completely satisfied with your purchase, and enjoy it for years to come. If you have any questions, or require technical assistance, please contact us at and one of our representatives will be happy to help. For more information about Kraus products, please visit: In order to activate your warranty and get faster access to customer support, please register your new Kraus product at: Sincerely, Kraus USA Customer Service 1

3 Prior to Installation: Make sure you have all necessary parts by checking the diagram and parts list. If any part is missing or damaged, please contact Kraus Customer Service at for a replacement Turn off the hot and cold water supply at the angle stops and turn on the old faucet to release any built up pressure. Remove existing faucet. Clean sink or countertop to remove any debris, plumber s putty, or silicone Place bucket under angle stops. Turn on to flush any debris prior to installing new plumbing. Shut off angle stops Pre-drilled hole size requirement: 1-3/8 Max countertop thickness without deck plate: 1-3/8 1, 2, or 3 hole installation For technical assistance or replacement parts, please contact Kraus Customer Service and one of our representatives will be happy to help: Toll-Free: or Customerservice@kraususa.com Tools you will need Adjustable Wrench Phillips Screwdriver Silicone Sealant (optional) Safety Goggles 2

4 Faucet Diagram and Parts List F A H B C I G D1 D2 E1 E2 E3 E4 3 A. Spray Head B. Faucet Body C. Base O-Ring D. Deck Plate Assembly D1. Deck Plate D2. Base Plate E. Mounting Hardware Assembly E1. Rubber Washer E2. Metal Washer E3. Mounting Nut E4. Mounting Screws (2) F. Spray Hose G. Supply Hose H. Weight I. Hot & Cold Waterlines

5 Soap Dispenser Diagram and Parts List a b c d e f a. Pump b. Dispenser Base c. Rubber Washer A d. Rubber Washer B e. Mounting Nut f. Dispenser Bottle 4

6 Step 1 Remove the mounting hardware (E) E1 E2 E3 E4 Step 2A For three-hole installation, deck plate assembly (D) and silicone sealant are required D1 D2 5 6

7 Step 2B For single-hole installation, deck plate assembly (D), and silicone sealant are NOT required Step 3 D1 D2 B C Insert faucet body (B) into hole on countertop or deck plate assembly (D) with base o-ring (C) attached. Attach mounting hardware (E) E1 E2 E3 E4 7 6

8 Step 4 B Adjust faucet body (B). Tighten mounting nut (E3) with wrench and mounting screws (E4) with Phillips head screwdriver E3 E4 Step 5 Connect spray hose (F) to supply hose (G). Tighten with wrench until snug. Install weight (H) on lowest point vertically on spray hose (F) G F H 7 8

9 Step 6 Thread hot & cold waterlines (I) onto angle stops. Tighten with adjustable wrench until snug. Turn on angle stops and check for leaks (DO NOT TURN ON) I 8

10 Step 7 a Disassemble soap dispenser b c d e f Step 8 c b d e Install dispenser base (b) with rubber washer (c) attached into hole on countertop. Re-install rubber washer (d) and mounting nut (d) on dispenser base (e) from underneath countertop. Tighten mounting nut (e) with adjustable wrench until snug 9

11 Step 8 b Screw dispenser bottle (f) to dispenser base (b) from underneath countertop. Tighten until snug. Fill dispenser bottle (f) from the top with 12 ounces of soap f Step 9 a Press Insert pump (a) into dispenser base (b) from top. Press pump several times to make sure soap evenly distributed b 10

12 Step 10 A F Remove the spray head (A). Hold tip of spary hose (F). Turn on faucet for 1 minute to flush any debris Step 11 Press Turn faucet on. Press button on spray head (A) to check if spray head (A) switches modes properly Press 11 6

13 Care & Maintenance *To keep the product clean & shining, follow the steps below: lose 25 Open 1. Rinse with clean water & dry with a soft cloth Do not clean with soaps, acid, polish, abrasives, or harsh cleaners 3. Do not use cloth with a coarse surface 4. Unscrew the aerator and clean when necessary Push Left *This Hot Water installation manual is subject to change without further notice. Download the Kraus Care & Maintenance Guide at: 12

14 Replacement Parts Faucet Parts B 1A A 3B A. Aerator 1B. Spray Head 2. Hose Guide 3.. Deck Plate 4. Set Screw 5. Lever 6. Set Screw 7. Handle 8. Cartridge Cover 9. Locking Nut 10. Cartridge 11. Base O-Ring 12. Deck Plate 13. Base Plate 14. Spacer Optional (Top Mount Sinks Only) 15. Rubber Washer 16. Metal Washer 17. Mounitng Nut 18. Mounting Screws 19. Hot & Cold Waterlines 20. Supply Hose 21. Spray Hose 22. Weight 23. Aerator Key Soap Dispenser 1. Pump 2. Dispenser Base 3A. Rubber Washer 3B. Rubber Washer 4. Mounting Nut 5. Dispenser Bottle 13

15 Trouble - Shooting If you have followed the instructions carefully and your faucet still does not work properly, take the following corrective steps: PROBLEM CAUSE ACTION Leaking from faucet handle Locking nut (11) may have come loose or cartridge (12) may need to be reseated Remove cover button (7). Loosen set screw (8) with 2.5 mm hex wrench (18). Remove handle (9). Unscrew cartridge cover (10) by hand. Tighten locking nut (11) with an adjustable wrench Water does not shut off completely Cartridge (12) may need to be adjusted or replaced Remove cover button (7). Loosen set screw (8) with 2.5 mm hex wrench (18). Remove handle (9). Unscrew cartridge cover (10) by hand. Unscrew locking nut (11) with an adjustable wrench. Remove cartridge (12). Check for cracks, and if O-ring is seated correctly. Reseat cartridge (12) 14

16 PROBLEM CAUSE ACTION Leaking between spray head and hose Spray head (1A) may be loose or washer (2) may not be seated correctly in the hose connection Tighten spray head (1A) by hand until snug. Make sure washer (2) is seated correctly Low flow Check valve connector (5) may be clogged with debris Loosen set screw (6). Remove spray hose & spring (3). Unscrew check valve connector (5) located at the bottom of spray hose & spring (3). Soak in 50/50 solution of warm water and vinegar for 5 minutes. Reinstall check valve connector (5) and spray hose & spring (3) 15

17 Maintenance - Cartridge Replacement Step 1: Remove button located at the top of the handle. Loosen the set screw with a hex wrench. Remove the handle and unscrew cartridge cover by hand Step 2: Unscrew the locking nut with an adjustable wrench. Remove ceramic disc cartridge Step 3: Place the new cartridge in the handle seat. Secure the cartridge with the locking nut and assemble the handle 16

18 Codes/Standards Applicable: NSF/ANSI Standard 61 certified by IAPMO NSF/ANSI Standard 372 certified by IAPMO GREEN LEAD FREE I APMOR&T Meets ASME A M/A GPM 6.6L/min maximum TM Water Efficiency HELP LINE Our customer service hours are Monday Friday, 9am 8pm EST. Be sure to visit our website at If you are a homeowner please contact a Kraus Customer Service Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY Toll-free Customerservice@kraususa.com If you are a plumbing contractor or trade professional please contact a Kraus Pro Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY Proservice@kraususa.com If you are an Authorized Partner please contact a Partner Support Representative at: Kraus USA, Inc. 12 Harbor Park Drive Port Washington, NY Partnersupport@kraususa.com In requesting warranty service, please be ready to provide: 1. Proof of purchase. 2. A description of the problem. 17

19 18

20 REGISTER YOUR PRODUCT TODAY Receive Proof of Ownership Access Customer Care & Installation Help Get Exclusive Kraus Offers & Promotions Scan to Register Online or visit We re always looking for ways to improve. Please take a moment to share your experience. Visit to let us know what you think about your new Kraus product. Contact Us to Learn More / / customerservice@kraususa.com Like & Follow KrausUSA Download the Kraus Care & Maintenance Guide at: