INSTALLATION INSTRUCTIONS
|
|
- Theresa Parks
- 6 years ago
- Views:
Transcription
1 MedMaster Auracyl Sconce for MRI Suites MRIMAS813 series Wall Mount Lamps: Incandescent, LED ADA Compliant Non-Ferrous Dimensions Nominal 8" 13" Nominal Luminous Opening 6" x 11" PROJECT INFORMATION Job Name Fixture Type Catalog Number Approved by housing: Non-ferrous marine grade extruded aluminum. Non-ferrous marine grade die-cast aluminum end caps. TGIC polyester powder coat finish 5-stage pre-treatment; Salt spray test: 1,000 hours. Antimicrobial finish on all exposed components of installed luminaire. Reflector: Die-formed non-ferrous marine grade aluminum. Full reflector/wire cover 92% reflectivity. decorative outer Lens: Acrylic translucent white lens standard. Nominal thickness.125". Optional decorative Lumicor resins see Ordering Information. Inner Lens: UV stabilized, high impact resistant, extruded 100% DR/acrylic frost lens. Nominal thickness.100". Lens secured in place by lens frame. Electrical: Replaceable high-brightness ANSI 3000K or 4000K LED array. Luminaire input 24V DC from remote-mounted, V AC, high power factor power supply (MRIPS-312 ordered separately). Dimming capability controlled through compatible 0-10V dimmer (supplied by others). MRI room EMI filter required (supplied by others). 5%-100% dimming range. Hardware: One non-ferrous stainless steel Phillips head fastener standard; six fasteners with IP64 option. Internal brackets and fasteners are non-ferrous and non-corrosive. Installation: Standard four-point mounting required. All power and signal wiring must be completely shielded in grounded conduit. Photometrics: For photometric information, go to patent: U.S. Patent No. 7,029,139. Warranty: One year warranty on mechanical defects. Three year warranty on LED lamps and internal power regulation components for defects resulting in a fixture lumen depreciation of 30% or greater. Warranty is void if all wiring is not completely shielded in grounded conduit. LISTINGS: UL and CUL listed for Damp Location covered ceiling and wall mount. NSF2 Splash Non-Food Zone. ADA compliant. Optional ETL certified IP64 in compliance with IEC All Kenall SSL Luminaires are tested to the IESNA LM standard requiring spectroradiometric measurements for CRI and CCT as well as goniophotometric measurements for lighting distributions and total luminous flux. COMPONENT ADA Option IP64 IEC Standard Kenall certifies product by both Underwriters and Intertek Testing Laboratories Specifications Cross Section 5.52" 8.33" Series MRIMAS813 Frame Type PAN Pane 3.96" Frame Type PAN Decorative Outer Lens AS Frosted Acrylic (Standard) CAP Clear Acrylic w/inner Perforation painted to match housing/frame finish NL* Acrylic Natural Leaf SS* Acrylic Silver Spun OL* Acrylic Oyster Linen ST* Acrylic Saffron Taipei PL** PETG Paper Leaf CD Custom Decorative Lens (Consult factory) installation Details 13.00" 10.10" 5.05" Finish MB Matte Black (Antimicrobial finish) MW Matte White (Antimicrobial finish) WS Warm Satin Painted Anodized CS Cool Satin Painted Anodized BR Bronze (Architectural) BE Beige CC Custom Color (Consult factory) Lamp Quantity 1 One Lamp 2.14" 8.31" (4).312" Dia. Mtg. Holes.875" Dia. Hole 1.50" Dia. Knockout for over box mounting DECORATIVE OUTER LENS AS Frosted Acrylic (Standard) OL Oyster Linen* FRAME FINISH MB Matte Black BR Bronze (Architectural) Outer Lens Finish Lamp Quantity 1 CAP Clear Acrylic w/inner Perforation ST Saffron Taipei* MW Matte White BE Beige Voltage Voltage V (Incandescent only) Volts DC (MRIPS-312 Power Supply required order separately) Lamp Type 25IT 25 Watt Incandescent (T10) 40IT 40 Watt Incandescent (T10) 6L30K 6 Watt 3000K LED 6L40K 6 Watt 4000K LED 14L30K 14 Watt 3000K LED 14L40K 14 Watt 4000K LED NL Natural Leaf* PL Paper Leaf** WS Warm Satin Painted Anodized Lamp/Ballast Type SS Silver Spun* * Lumicor Lumiclear Acrylic Resin ** Lumicor Lumiform PETG Resin CS Cool Satin Painted Anodized Option Options IP64 IP64 certified to IEC mri LUMINAIRE connection per power supply Luminaire Amps/ Max. Luminaires/ Number Luminaire Power Supply/per room MRIMAS813 (6W) MRIMAS813 (14W) DImEnsional Data Ordering INformation MRIMAS P: F: Lakeside Drive Gurnee, Illinois The Kenall product shown on this page is manufactured in the USA with components purchased from US suppliers, and meets the Buy American requirements under the ARRA. Kenall has not determined the origin of its domestically purchased components or the subcomponents thereof. Content of specification sheets is subject to change; please consult for current product details Kenall Mfg. Co. All rights reserved.
2 1020 Lakeside Drive Gurnee, IL MEDMASTER MRI AURACYL SCONCE MRIMAS813 INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS TO PREVENT MRI MACHINE INTERFERENCE, ALL DC POWER AND DIMMING SIGNAL WIRING MUST BE COMPLETELY SHIELDED WITHIN GROUNDED CONDUIT AND A SUITABLE MRI ROOM EMI FILTER MUST BE INSTALLED ON EACH LINE. READ AND FOLLOW ALL PRODUCT INSTRUCTIONS THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATION CODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS INVOLVED. SAVE THESE INSTRUCTIONS Disconnect power to all circuits before wiring system. Install in accordance with all national, state, and local codes. Do not connect to an ungrounded supply. Wiring connections must be made internal to the enclosure. Failure to install unit on a mechanically-sound surface may result in personal injury, physical damage, or potential fire hazard. Use installation procedures appropriate for an environment involving MRI and sensitive electronic equipment. Read all markings and labels to ensure correct installation of the power supply. Supplemental instructions may be located on the enclosure, in addition to this instruction sheet, regarding orientation, or mounting restrictions. Read instructions provided with the MedMaster MRIPS-312 external power supply for proper installation and electrical connection to the lighting system. INSTALLATION INSTRUCTIONS This instruction sheet applies for the MRI MedMaster Auracyl Sconce MRIMAS813. A separate instruction sheet is provided in the MRIPS-312 external power supply. Both sheets are intended to provide comprehensive instructions on fixture installation and wiring. The MRI MedMaster Sconce lighting system contains sensitive electronics. Take care to avoid damage by improper handling or static electricity discharge (ESD). Either type of damage could render the system inoperable or cause latent failure. I. Luminaire Mounting Procedure 1. Remove the screw(s) from the luminaire and unhook front housing (B) from the baseplate assembly (C). STANDARD VERSION IP64 VERSION F /23/2010 Page 1 of 5
3 2. Remove the reflector/ wireway to expose the mounting holes. *Note: When removing the wireway, DO NOT remove the LED boards. REFLECTOR REMOVAL LED TRAY REMOVAL 3. Remove LED tray by removing the four nuts at the corners, this will expose the supply wire hole. 4. Remove 1.50 knockout in the center of the baseplate (C) around the supply wire hole. 5. Use the baseplate (C) as a template and mark the pilot holes (E) on the mount surface. Orient the baseplate (C) with the angle bracket hook (D) at the top. MOUNTING HOLES SUPPLY WIRE AND MOUNTING HOLE LOCATIONS 6. IP64 version only: To ensure wet location rating, apply square gasket (supplied) around wire access opening and four round gaskets (supplied) around the mounting holes on the wall side of the baseplate. 7. Disconnect facility power to the electric power supply leads. 8. Mount the baseplate. F /23/2010 Page 2 of 5
4 II. Electrical Connection 9. Mount and wire the MRIPS-312 external power supply per the procedures provided in the supplementary instruction sheet. Run conduit and DC wiring to an MRI room EMI filter sized to the load of the power supply (supplied by others). Make sure wiring is completely enclosed in grounded conduit. Any gaps, regardless of size, must be closed or wrapped in copper foil tape. 10. If a 0-10V dimmer is to be connected, install at this time. Dimmer must be installed outside the shielded MRI environment with an intermediate MRI room EMI filter to the luminaires. Kenall recommends using a Leviton lllumatech IP710 series dimmer or Grafik Eye GRX-TVI control interface. Contact Kenall for suitability of using an alternate sink-type 0-10V dimmer. WARNING: ALL DC POWER AND DIMMING SIGNAL WIRING MUST BE RUN THROUGH SEPARATE EMI FILTERS. WIRING DIAGRAM 11. After the luminaires are mounted and secured, access the internal junction box to gain access to supply connections. Each wire is labeled and color coded for easy identification. 12. Run the 24VDC supply from the EMI filter to the luminaire(s) using at least 18 AWG wires. Class 1 wiring is required. Make sure wiring is completely enclosed in grounded conduit. Any gaps, regardless of size, must be closed or wrapped in copper foil tape. Special attention should be paid to the wiring entry point into the shielded space. See Figure above. 13. Run the dimming signal (if applicable) from the dimmer EMI filter to the luminaire(s) using at least 18AWG wires. Make sure wiring is completely enclosed in grounded conduit. Any gaps, regardless of size, must be closed or wrapped in copper foil tape. Special attention should be paid to the wiring entry point into the shielded space. See Figure above. 14. Make DC supply and (optional) dimmer control connections within each luminaire. Cap gray and violet leads if dimmer is not connected. 15. Reinstall all provided bracketry and internal enclosures provided with the luminaire. These parts are critical to the overall EMI shielding of the system. 16. Connect power to external power supply and test for proper operation of lighting system. Make sure all LEDs are lit and dimming operation works as intended (if connected). 17. Test operation of lighting during MRI machine idle mode and during scanning operations. 18. Fill out the Installation Registration Form (attached to MRIPS-312 instruction sheet) and fax to Kenall at (847) F /23/2010 Page 3 of 5
5 IV. Conclusion of Luminaire Mounting Procedure 19. Reattach the LED tray to the baseplate. 20. Reattach the reflector/ wireway with the screws that were removed in step Hook the front housing (B) onto the angle bracket hook (D). 22. Replace the screw(s) removed in step 1. NOTE: DO NOT PUSH ON OUTER LENS WHEN MOUNTING THE FRONT HOUSING. 23. Standard luminaire only: Check to make sure the housing is locked in place. This is achieved when screw (A) is behind the baseplate flange (C). See illustration on next page. NOTE: DO NOT PUSH ON OUTER LENS WHEN MOUNTING THE FRONT HOUSING. STANDARD LUMINAIRE SCREW DETAIL CUSTOMER SERVICE For technical assistance, call KENALL ( ) WARRANTY When installed to these instructions, this product is warranted by Kenall to be free of defects in workmanship and materials for a period of one year from the date of invoice. The DC power supply contained in the external power supply carries a three year warranty from the date of invoice. The warranty is void if all power and dimming signal wiring is not completely shielded in grounded conduit and installed with a suitable MRI room filter (by others). Kenall reserves the right to issue credit, repair, or replace the defective merchandise, at its discretion, upon notification and confirmation by its local representative of the defect. Kenall also reserves the right to examine the defective product if the defect is questionable and to deny the warranty herein for any product altered, improperly installed, or installed in applications for which it is not intended. Kenall assumes no responsibility for labor or freight costs incurred in connection with the installation, removal, or replacement of products determined to be defective or any other consequential or incidental damages arising from the use of the product. Kenall s entire liability on any claim of loss or damage resulting from a defective product is limited to the replacement price of the product. The foregoing warranty is exclusive of all other warranties and no other warranties of any kind are expressed or implied. F /23/2010 Page 4 of 5
6 1020 Lakeside Drive Gurnee, IL MedMaster MRI Installation Registration Form For warranty purposes, please fill out this form and return to Kenall by fax at (847) I certify that the lighting installation for the listed MRI suite location is completed per the provided installation instructions and to the best of my abilities. Please check off items to denote status: Installation instruction sheets for MRIPS-312 power supply and individual luminaire(s) read and followed. MRIPS-312 power supply and EMI filters are located outside the shielded enclosure. All DC supply wiring is completely enclosed within grounded conduit. Installation has no ungrounded/unshielded portions of conduit or openings of any size or shape. All dimming signal wiring is completely enclosed within grounded conduit. Installation has no ungrounded/unshielded portions of conduit or openings of any size or shape. Check here if dimming is not applicable: MRI Room EMI filters for the 24VDC supply are of the type intended for MRI suites and are sized to the electrical load. DC supply power and dimming signal are NOT running through the same EMI filter. Check here if dimming is not applicable: Lighting system fully tested (including dimming operation, if applicable) while MRI machine is in idle and scan operation mode. If any of these steps cannot be completed or you need technical assistance, please contact Kenall Technical Support at KENALL ( ). Electrical Contractor Name: City/State: Phone: Installation Date: Installation Site Name: City/State: FAX FORM TO (847) (Do not write below line) Kenall Received By: Received Date: F /23/2010 Page 5 of 5
MEDMASTER EXTERNAL POWER SUPPLY
PROJECT INFORMATION Job Name MEDMASTER EXTERNAL POWER SUPPLY MRIPS-312 SERIES PRODUCT FEATURES: Recommended for MRI CleanScene, Downlight, Auracyl Sconce, Stratalume Undercabinet and Envela Remote mounted
More informationMEDMASTER DOWNLIGHT Luminaires for MRI Applications
PRODUCT FEATURES:»» 6" sealed, recessed downlight with regressed or flush lens trim»» Designed for MRI applications with non-ferrous construction and RF-free electronics»» Delivered lumens: 591-2,953 lm»»
More informationMEDMASTER CLEANSCENE MRI/Imaging Suite Luminaires
MEDMASTER CLEANSCENE MRI/Imaging Suite Luminaires CSMRI SERIES PRODUCT FEATURES:»» Recessed ceiling mount grid; 4' 4'»» Non-ferrous construction»» Expansive offering of high quality graphic images»» Antimicrobial
More informationOptions AMF Antimicrobial Finish (All Exposed Surfaces) BLK Black Doorframe. Accessory
PROJECT INFORMATION Job Name LightBox CSMRI SERIES PRODUCT FEATURES:»» Recessed ceiling mount grid; 2' 4'»» Non-ferrous construction»» Antimicrobial finish option available»» Expansive offering of high
More informationMEDMASTER DOWNLIGHT Luminaires for Surgical Applications
PRODUCT FEATURES: 6" sealed, recessed downlight with regressed or flush lens trim Conducted emissions controlled as per MIL-STD-461F Delivered lumens: 794-5,543 lm 1% Dimming via 0-10V, DALI or EcoSystem
More informationseem 4 suspended led features dimensional data mounting information performance Narrow extruded aluminum 4 linear direct LED.
suspended led features Narrow extruded aluminum 4 linear direct LED. Individual units and continuous runs in 1 increments. Continuous frosted acrylic lens provides uninterrupted illumination, without pixels
More informationProject: Type: Qty: QH2L. Options QH2L 27 3 /8" 23 3 /16" 3 1 /2" O.D. Pole. Options
Quadro H LED Project: Type: Qty: QHL _ Series Mounting Optics Light Engine CCT Finish Voltage Option _ Pole Series Height Finish Options Series Mounting Optics Light Engine CCT Finish Voltage QHL Quadro
More informationSAVE THESE INSTRUCTIONS
MILLENIUM METREX METEL SERIES INSTALLATION INSTRUCTIONS IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS DO NOT USE OUTDOORS. DO NOT MOUNT NEAR GAS OR ELECTRIC HEATERS. 1 APPLICATIONS EQUIPMENT
More informationSeem 4. Narrow extruded aluminum 4" linear direct/indirect LED with Pop-lens options.
LED DIRECT/INDIRECT flush lens top & bottom pop-up lens & pop-down lens pop-up lens & flush lens bottom end detail single point corner suspension linear direct only companion wall to ceiling corner companion
More informationDriver Info. Construction Thermal Management: Superior thermal management with die-cast aluminum heatsink. Ambient Temperature:
WP3LED55 Project: Type: Prepared By: Date: 82W, 65W and 55W LED wallpacks. Available with up to 9,000 lumens and 121 LPW. Up to 100,000 hour L70 lifespan. 5-Year Warranty. Color: Bronze Weight: 16.8 lbs
More informationEDGE EV3WET 3 Recessed Linear WET
Project Name Date Type 4-13/16 (122mm) EDGE EV3WET 3 3-11/16 (94mm) 4-3/4 (121mm) 5/16 (8mm) Key Features Approved for wet location unless otherwise noted. IP65 and IK10 rated Fixture is built using corrosion
More informationNera. detail. fixture information. Unique aesthetic inspired by the visual void design philosophy. Luminaire sizes available in 2 x2, 3 x3 and 4 x4.
LED bottom detail inside lens detail white finish palladium finish 2016 DIMENSIONAL DATA FEATURES Unique aesthetic inspired by the visual void design philosophy. Luminaire sizes available in 2 x2, 3 x3
More information25 Sign / Wall Lighter 4324 LED Series Extruded Aluminum, PicoPrism LED revision 9/9/15 kl_4324led_series_spec.pdf
Type: Catalog number: / / Wattage / Lamp(s) Finish Options: See page 2 ing Options: See pages 3-5: Approvals: Date: Page: 1 of 5 Specifications ORDERING INFORMATION Light Engine Length l 4324P70 / 16L3KUV
More informationOptions. Pole and Arm. Suitable for wet locations
Catalog number: / / / Mtg. Fixture Electrical Module Finish See page 2 See page 3 Options Pole and Arm Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for
More informationEDGE EX6WET 6 Suspended Direct Linear WET
Project Name Date Type 4-11/16 (119mm) EDGE EX6WET 6 Suspended Direct Linear WET 5-3/4 (146mm) 5/16 (8mm) Key Features Approved for wet location unless otherwise noted. IP65 and IK10 rated Fixture is built
More informationSeem mm 4.50" 4.00" 101.6mm. Narrow 4" linear fluorescent allows for both individual or continuous runs.
FLUORESCENT recessed companion wall mount companion DIMENSIONAL DATA FEATURES Narrow 4" linear fluorescent allows for both individual or continuous runs. Frosted acrylic flush lens provides even illumination,
More informationFINA F48B 48 Direct and Uplight Architectural Round
Project Name Date Type FINA F48B 48 Direct and Uplight Architectural Round 4-1/2 4-7/8 (114.3mm) (123.8mm) 45-15/16 (1166.8mm) Key Features Extruded aluminum housing is rolled and welded for seamless finish
More informationCLARA CLA SUSPENDED, WALL, SURFACE
CLARA CLA STANDARD SIZES 4.75" Hollow Lensed Body Configurable in 2ft increments (suspended mount) ADA-Compliant 2ft/4ft wall sconce LAMPING LED - 80+ CRI - 3000K/3500K/4000K Dimming down to 0% FINISH
More informationFINA F48 48 Direct and Uplight Architectural Round
Project Name Date Type 48 Direct and Uplight Architectural Round 4-1/2 4-7/8 (114.3mm) (123.8mm) 45-15/16 (1166.8mm) Key Features Extruded aluminum housing is rolled and welded for seamless finish with
More informationEDGE EX3B-WW 3 Suspended Bidirectional Linear Wall Wash
Project Name Date Type 5-3/8 (136.5mm) EDGE EX3B-WW 3 7/16 (11.1m) 3-1/2 (88.9mm) 11/16 (17.5m) Key Features 6063-T5 Extruded aluminum housing Extruded aluminum module with miro reflector for perfect wall
More informationProject: Type: Qty: SA1L. Optics Mounting Light Engine CCT Finish Voltage Options. Series SA1L-XX-1-NH SA1L-XX /2" O.D.
Saturn LED Project: Type: Qty: SAL Series Optics Mounting Light Engine CCT Finish Voltage Pole Series Height Finish Pole Options Option Series SAL Saturn LED Optics Mounting Light Engine CCT Finish Voltage
More informationFINA F36B 36 Bidirectional Architectural Round
Project Name Date Type FINA F36B 36 Bidirectional 4-1/2 4-7/8 (114.3mm) (123.8mm) 33-15/16 (862mm) Key Features Extruded aluminum housing is rolled and welded for seamless finish with 1/4 trim Aluminum
More informationEX3B. Project Name _ K 4000K. R_x_ Rectangle. MAC JB Junction Box Movable AC
EX3B Project Name Date Type SUSPENDED BIDIRECTIONAL LINEAR LUMINAIRE 3-1/2 (88.9mm) 5-3/8 (136.5mm) LED Product Partner 6063-T5 Extruded aluminum housing Highly reflective die-formed white painted reflector
More informationJ TO 4000 LUMEN 8 LED CYLINDER HYPERBOLIC/PARABOLIC/WALLWASH OPEN APERTURE LC8 SERIES DIMENSIONS 1-1/4
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from 8 to over 50 Efficacies up to 80 lm/w Superior-quality white LED light output using Chip on Board technology
More informationIVR15-RPS 1.5 O.D. Solid State Illuminated Rail Remote Power Supply
O.D. Solid State Illuminated Rail Remote Power Supply 1.50 RECOGNIZED 0.3 90 APERTURE Ends of Illuminated rail field cutable to a minimum of 2 1/8 in length. Illuminated rail is available with a minimum
More informationSURFACE MOUNTED. Project. Type. Notes. culus Listed Type I.C.
Project Type Notes PERFORMANCE AT 4000K NOMINAL LUMEN OUTPUT INPUT WATTS* EFFICACY 2400 lm 22.76 W 103 lm/w 4000 lm 41.17 W 97 lm/w 5000 lm 53.46 W 94 lm/w 6500 lm 70.65 W 92 lm/w 7700 lm 85.33 W 90 lm/w
More informationEX3. Project Name _ K. R_x_ Rectangle. MAC JB Junction Box Movable AC
EDGE EX3 Project Name Date Type SUSPENDED DIRECT LINEAR LUMINAIRE 3-1/2 (88.9mm) 5-3/8 (136.5mm) LED Product Partner 6063-T5 Extruded aluminum housing Highly reflective die-formed white painted reflector
More informationRECESSED T-Bar & Drywall. Project. Type. Notes 23 15/16" 23 7/8" SIDE VIEW. culus Listed Type I.C.
Project Type Notes PERFORMANCE AT 4000K NOMINAL LUMEN OUTPUT INPUT WATTS* EFFICACY 2500 lm 23.1 W 109 lm/w 3000 lm 28.49 W 105 lm/w 4000 lm 39.22 W 102 lm/w 4400 lm 43.64 W 101 lm/w * Based on a 2'x2'
More informationHAZARDOUS LOCATION CLASSIFIED AREAS LW1 AND LW2 SERIES DOWN OR UP OPTICS
H6..H Project: Fixture Type: Location: Contact/Phone: FINIA LED WALL MOUNTED HAZARDOUS LOCATION CLASSIFIED AREAS LW AND LW SERIES DOWN OR UP OPTICS LED W, W, AND 8W PRODUCT DESCRIPTION The Finia LED LW
More informationCC/CCS21 21" Post Top Mounted, Curvilinear, LED revision 5/9/11 kim_cc21pled_spec.pdf
Catalog number: Approvals: / / / / Mtg. Fixture Electrical Module Finish Options See page 4 See page 2 See page 3 Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate
More informationEDGE EX2 2 Direct Suspended Linear
Project Name Date Type 4-3/4 (120.7mm) EDGE EX2 2 Direct 2-1/4 (57.2mm) 2-7/8 (73mm) Key Features 6063-T5 Extruded aluminum housing Highly reflective die-formed white painted reflector Wiring access available
More informationEDGE EX3I 3 Suspended Indirect Linear
Project Name Date Type 5-/2 (40mm) EDGE EX3I 3 3-/2 (88.4mm) Key Features 6063-T6 Extruded aluminum housing Highly reflective = white painted reflector Room side maintance for LED system 5-year limited
More informationmillenium StretcH Architectural High Abuse and Rough Service Flexible Lighting System Linear Fluorescent Lighting
millenium StretcH Architectural High Abuse and Rough Service Flexible Lighting System Linear Fluorescent Lighting HA 2 Millenium Stretch What's New Millenium Stretch is now available in a new 5"width In
More informationLUCEN 2x2 ARCHITECTURAL RECESSED LUMINAIRE
Project Name Date Type ARCHITECTURAL RECESSED LUMINAIRE 3-3/4 (95.3mm) 23-3/4 (603.3mm) 23-3/4 (603.3mm) Pre-painted formed 22 gauge cold rolled steel housing Highly reflective die-formed white painted
More informationTUNABLE SPECTRUM/TUNABLE WHITE
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Tunable natural white light on the Planckian curve Very high CRI and R9 values throughout range from 1650K thru 4000K (variable warm) and 2700K thru 0K (variable
More informationLED DockLight. Sustainable lighting with powerful output. UL listed for wet locations. Standard 5 year warranty
Patent # USD0587833 Sustainable lighting with powerful output Industrial luminaire with 15 watt power consumption Rated life of 50,000 hrs to 70% lumen maintenance Highly impact resistant; LED technology
More informationkenall dark sky luminaires
kenall dark sky luminaires Millenium Finite Wall Mount Millenium Edge Ceiling Mount Herculux Wall and Ceiling Mount Kenall's dark sky solution As more buildings are constructed and equipped with powerful
More informationTUNABLE SPECTRUM/TUNABLE WHITE
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Tunable natural white light on the Planckian curve Very high CRI and R9 values throughout range from 1650K thru 4000K (variable warm) and 2700K thru 0K (variable
More informationfor environmentally critical applications
Enviroseal LINEAR Wraparound Luminaires for environmentally critical applications ENVIRONMENTAL Transportation Food Processing Hazardous Location table of contents ES, HES, FES Series EnviroSeal Features...4-5
More informationDCD2 Recessed LED Downlight Commercial New Construction 4", 6", 8" Aperture
PRODUCT SPECIFICATIONS Frame-in Kit MOUNTING FRAME: Die-cast aluminum. JUNCTION BOX: Galvanized steel. Equipped with (4) /2" and (2) 3 /4" knockouts with pryout slots to allow straight conduit runs. Approved
More informationPRODUCT SPECIFICATIONS
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT One fixture converts nearly any manufacturers incandescent, CFL or H.I.D. fixtures with a rough-in inner diameter of 7-5 /8 to 8-1 /8 diameter to high efficiency
More informationPark Avenue DETAILS. IP67 EPA: 1.8 FT 2 Weight: 45 lbs - 20 kg
Park Avenue Park Avenue DETAILS The PARK AVENUE Series, with its mid-century modern styling, is designed to disperse a vast amount of light while maintaining a timless look. The PARK AVENUE is Intended
More informationSkydome. 2', 3' and 4' diameter recessed direct LED with lens. Frosted acrylic diffuser provides high transmission and uniform distribution.
LED DIMENSIONAL DATA FEATURES 2', 3' and 4' diameter recessed direct LED with lens. Frosted acrylic diffuser provides high transmission and uniform distribution. 24." 69.6mm 36." 914.4mm 48." 1219.2mm
More informationSeries Mounting Accessory Distribution Source Color Temperature Voltage 10DEG 20DEG 40DEG 60DEG 60X20DEG
700YK1 SMALL YOKE MOUNT 5 7-3/4 (321mm) 700KNL1 KNUCKLE MOUNT 5 7-3/8 (171mm) 6-3/16 (157mm) 6-3/16 (157mm) Construction Rugged die cast aluminum housing with clear tempered glass lens & 100% silicone
More informationCONVERJ CJ22 2x2 Architectural Recessed
Project Name Date Type CONVERJ CJ22 2x2 Architectural Recessed 3-1/2" (88.9mm) 24" (609.6mm) Key Features Formed 20 gauge cold rolled steel housing. Highly reflective die-formed white painted reflector.
More informationCONVERJ CJ14 1x4 Architectural Recessed
Project Name Date Type CONVERJ CJ14 1x4 Architectural Recessed 3-1/2" (88.9mm) 12" (304.8mm) Key Features Formed 20 gauge cold rolled steel housing. Highly reflective die-formed white painted reflector
More informationSkydome. 2', 3' and 4' diameter surface mount direct LED with frosted acrylic lens.
LED SURFACE MOUNT bay blue - gloss fabulous fuscia - gloss golf green - gloss modest mushroom - gloss titanium silver matte black suspended companion recessed companion DIMENSIONAL DATA FEATURES 2', 3'
More information4" LED SPECIFICATIONS LOW-PROFILE ADJUSTABLE DOWNLIGHT
LED This specification grade low-profile adjustable LED downlight delivers high performance for ultra-shallow ceiling plenum installations while maintaining a beautiful architectural ceiling appearance.
More informationMEDMASTER TROFFER Luminaires for MRI/Imaging Suites LED MRIT SERIES
MEDMASTER TROFFER Luminaires fr MRI/Imaging Suites PRODUCT FEATURES: Recessed munt Grid; 2' 2', 2' 4' Nn-ferrus cnstructin safe fr sensitive MRI equipment High-utput, high-cri LED lamp ptins NSF2 rating
More informationLuminaire characteristics: Source: Lumen maintenance: Optics: Material: Mounting: Electrical: Dimming: Finish: Weight: Warranty: Ratings:
Page: 1 of 6 Collection of pendants luminaire for commercial and institutional applications. Canopy mounted, with complete range of optical accessories, Studio is a flexible solution for general lighting
More informationVerve IV. Suspended linear direct/indirect fluorescent with radial or flat baffle or parabolic louver.
FLUORESCENT BAFFLE/LOUVER radial blade baffle flat blade baffle flat blade parabolic louver DIMENSIONAL DATA FEATURES Suspended linear direct/indirect fluorescent with radial or flat baffle or parabolic
More informationK199 CALIFORNIA - LED ACORN PRODUCT SPECIFICATIONS 39 1/8"
The K99 California luminaire was one of the original acorn styles that graced the streets of North American towns and cities, particularly in Southern California. Teamed with King Luminaire s high performance
More informationCONVERJ CJ24 2x4 Architectural Recessed
Project Name Date Type CONVERJ CJ24 2x4 Architectural Recessed 3-1/2" (88.9mm) 24" (609.6mm) Key Features Formed 20 gauge cold rolled steel housing. Highly reflective die-formed white painted reflector
More informationMA20/MA21 SERIES MAYA - LED Post Top
TYPE: QUANTITY: PROJECT: / SERIES Post Top CATALOG NUMBER: FIXTURE WATTAGE VOLTAGE FINISH OPTION OPTION OPTION OPTION 7 1 2 3 4 1- Cast aluminum LED heat sink. 2- Optical system assembly. 3- Set of two
More informationP15 - P44: 5-3/4 P62: 6-1/2. SCA Sloped ceiling TrimLock K K K K TW Tunable white (80 CRI, 2700K 5000K) 65 Open
CATALOG #: - : 5-3/4 : 6-1/2 TYPE: ø4-1/2 ø5-1/2 PROJECT: NEW CONSTRUCTION AND REMODEL FEATURES Williams TrimLock reflector retention system eliminates trim sag Williams turn-key Power over Ethernet (PoE)
More information2 1/2. Applies to both UP & DOWN. Specify quantity. Requires 8" blank See integrated controls guide for more details.
Project Type Louver Notes Satin Ribbed Lens Spotless Lens PERFORMANCE PER LINEAR FOOT AT 3500K (SR) 2 1/2 NOMINAL LUMEN OUTPUT INPUT WATTS EFFICACY DISTRIBUTION UP DOWN 80up/20down at 1000 lm/ft 800 lm/ft
More informationEDGE EX4B 4 Suspended Bidirectional Linear
Project Name Date Type 4-3/4 (120.7mm) EDGE EX4 4 3-3/4 (95.3mm) 4-7/16 (112.7mm) Key Features 6063-T5 Extruded aluminum housing Highly reflective die-formed white painted reflector Room-Side Maintenance
More informationHBC-20 - LED HIGH BAY
To prevent death, injury or damage to property, this product must be installed in accordance to National Electrical Code (NFPA70) in the US or Canadian Electrical Code (CSA.) in Canada. Risk of fire or
More informationBLACK BODY DIMMING 800/1300/1500 LUMEN 6 LED NEW CONSTRUCTION/REMODEL
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Black Body Dimming duplicates halogen dimming, offering a soft, natural, warm glow as light levels are reduced CCT warms from 3000K to K, while staying on the
More informationCONVECT RADIATE CONDUCT
The King Luminaire KCK445R Sol-Lux LED Conversion Kit offers a simple way to convert to high efficiency LED. Through Tri-Thermal Management, the KCK445R Sol-Lux reduces heat via convection, radiation and
More informationMorino DETAILS IP67. Contact factory for WIRELESS CONTROLS and further details REV. 5: 06/18. EPA: 1.8 FT 2 Weight: 35 lbs - 16 kg
Morino Morino DETAILS The updated Victorian style Morino, designed with decorative arms that lend itself perfectly to any post classic settings. Conceived with a high efficiency heat sink, integrated Utility
More informationEDGE EX3 3 Suspended Direct Linear
Project Name Date Type 5-3/8 (36.5mm) EDGE EX3 3 Suspended Direct Linear 3-/2 (88.9mm) Key Features 6063-T5 Extruded aluminum housing Highly reflective die-formed white painted reflector Wiring access
More informationSeem 6. Narrow 6 aperture slot fluorescent luminaire that integrates with the ceiling for a clean unobtrusive aesthetic.
Seem 6 FLUORESCENT GRID parabolic louver DIMENSIONAL DATA grid 5.53" 14.6mm FEATURES Narrow 6 aperture slot fluorescent luminaire that integrates with the ceiling for a clean unobtrusive aesthetic. Frosted
More informationQuick Facts LED RECESSED LUMINAIRES
TYPE CATALOG # PROJECT NOTES LED RECESSED LUMINAIRES rnook-16 Strength, versatility, and unmatched style come together in the rnook-16 recessed wall light from Holm to produce a uniquely crafted luminaire
More information4DS 4.5 Downlight Square
CATALOG #: - : 5 : 6-1/2 4-1/2 5-1/2 TYPE: PROJECT: NEW CONSTRUCTION AND REMODEL FEATURES Dim to warm from 1800K to 3000K CCT, minimum 95 CRI 4 inch aperture is unobtrusive in small scale spaces Square
More informationAvenue B. Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid regressed trim or flush lens.
LED corrugated regress trim solid regress trim flush lens DIMENSIONAL DATA FEATURES Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid regressed trim or flush lens.
More informationSkydome. Pendant mount LED round dome with acrylic diffuser. Nominal 2', 3' or 4' diameter housings are available.
LED STEM/CABLE MOUNT bay blue - gloss fabulous fuscia - gloss golf green - gloss modest mushroom - gloss titanium silver matte black cable mount canopy detail surface mount companion recessed companion
More information3" LED SPECIFICATIONS ULTRA SHALLOW FIXED DOWNLIGHT
Small aperture LED downlight with architectural appearance housed in an ultra-shallow " above the ceiling housing. LED module and optics are modular for ease of replacement. Wood ceiling option allows
More information2 LED downlight. Discreet styling, bold performance. RABWEB.COM
2 LED downlight Discreet styling, bold performance. RABWEB.COM 888 722-1000 Clean, unobtrusive design delivers smooth and abundant light from an aperture just over 1 inch wide. 8W replaces 50W MR16 with
More informationCubic SurroundLite TM
Project Type VL Optic Notes Spotless Lens Louver PERFORMANCE PER LINEAR FOOT AT 3500K (SR) 6 1/16 2 1/8 NOMINAL LUMEN OUTPUT INPUT WATTS EFFICACY DISTRIBUTION UP DOWN 75up/25down at 1000 lm/ft 800 lm/ft
More informationEDGE EX44 4 x 4 Suspended Direct Linear
Project Name Date Type 4 (101.6mm) EDGE EX44 4 x 4 Suspended Direct Linear 3-3/4 (95.3mm) 4-7/16 (112.7mm) Key Features 6063-T5 Extruded aluminum housing Highly reflective die-formed white painted reflector
More informationLED CANOPY with j-box
ASD Garage Canopy Luminaire with junction box provides a slim, low profile solution for easy mounting. Built with rugged cast aluminum, this luminaire is available with surface or pendant mount. J-Box
More informationDomia DETAILS CY55P1A CY55T4 IP67
Domia Domia DETAILS The Domia offers smooth curves and a timeless shape blends easily into any environment. With a flat lens design, the DOMIA family enhances any project while offering high performance
More informationK601D COACH LANTERN - LED PRODUCT SPECIFICATIONS
The K601D is a cost effective coach lantern with a historical appearance that offers high performance Advanced LED Technology with our signature P4 optical system. It has excellent spacing and low glare
More informationPERIMETER - RECESSED. Regressed 3" BMPRLED OPRI ( 1) 14 PRODUCT ID LINEAR OR CORNER QTY TOTAL LENGTH. 3D VIEW - Inside Corner Pattern
Flush Regressed 2" Regressed 3" Project Type 6 7 Notes PERFORMANCE PER LINEAR FOOT AT 4K 2 3 NOMINAL LUMEN OUTPUT INPUT WATTS* EFFICACY 4 lm/ft 3.6 W/ft 11 lm/w 5 lm/ft 4.6 W/ft 19 lm/w 75 lm/ft 7. W/ft
More information2" LED SPECIFICATIONS ADJUSTABLE DOWNLIGHT & WALL WASH
" LED The ELEMENT " adjustable downlight boasts a." aperture and.75" ceiling cutout. Newly developed aiming/locking mechanism offers -5º tilt, 3º rotation, and ELEMENT's patented high-low lamp positioning.
More informationPERIMETER - RECESSED. Flush BBPRLED OPRI ( 1) 14 PRODUCT ID LINEAR OR CORNER QTY TOTAL LENGTH. 3D VIEW - Inside Corner Pattern
Regressed 4" Regressed 3" Regressed 2" Flush Project Type 8 6 15 /16 5 15 /16 Notes 4 3 2 PERFORMANCE PER LINEAR FOOT AT 4K NOMINAL LUMEN OUTPUT INPUT WATTS* EFFICACY 4 lm/ft 3.6 W/ft 11 lm/w lm/ft 4.6
More information(L 70 ) 3000K / 4000K / 5000K 12 50,000 50, K / 4000K / 5000K 15 50, K / 4000K / 5000K 18 50,000
Applicable Cooler Door Models: WATTS (NOMINAL) MODEL LIFE (L 70 ) DIMENSIONS (L x W x H) Nom CCT 9 36RDLxx 3ft x 1in x ¾ H 12 48RDLxx 4ft x 1in x ¾ H 15 60RDLxx 5ft x 1in x ¾ H 18 72RDLxx 6ft x 1in x ¾
More information6DS 6 Downlight Square
CATALOG #: L7 - L13: 5-7/8 L21: 7-3/8 6 TYPE: PROJECT: NEW CONSTRUCTION AND REMODEL FEATURES Dim to warm from 1800K to 3000K CCT, minimum 95 CRI Beam angles ranging from 25º narrow to 65º wide for tailored
More informationBLACK BODY DIMMING 800/1300 LUMEN 8 LED CYLINDER HYPERBOLIC / PARABOLIC / WALLWASH / OPEN APERTURE LC8 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Black Body Dimming duplicates halogen dimming, offering a soft, natural, warm glow as light levels are reduced CCT warms from to 1K, while staying on the Black
More informationCampana DETAILS CN55P1A. IP67 EPA: 1.8 FT 2 Weight: 52 lbs - 24 kg CN55P1B
Campana Campana DETAILS Luminaires in the CAMPANA series coexist perfectly with environments such as parks, pedestrian areas, waterfront projects, shopping centres, streets or avenues. This series of luminaires
More informationProject Name. 23-3/4 (603.3mm)
LUCEN 2x4 Project Name Date Type ARCHITECTURAL RECESSED LUMINAIRE 3-3/4 (95.3mm) 48 (1224mm) 23-3/4 (603.3mm) Pre-painted formed 22 gauge cold rolled steel housing Highly reflective die-formed white painted
More informationNotes: 4 3/4" 121mm. (1) Compatible with Redwood systems. See integrated controls guide for further details
PROJECT INFORMATION Project: Notes: Type: DIMENSIONS SECTION VIEW 4 3/4" 121mm 5 1/32 128mm 5 5/8 143mm ORDERING CODE 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 PRODUCT SPECIFICATIONS 1 PRODUCT ID 2 VERSION
More informationProject Name. 23-5/8 (600.2mm)
LiFT 2x2 Project Name Date Type ARCHITECTURAL RECESSED LUMINAIRE 23-5/8 (600.2mm) 23-5/8 (600.2mm) 5-5/8 (143mm) Formed 20 gauge cold rolled steel housing Highly reflective die-formed white painted reflector
More information800 TO 9000 LUMEN 8 LED SILENT CEILING DOWNLIGHT HYPERBOLIC OPEN APERTURE L8 SERIES
ENVIRONMENTALLY FRIENDLY, ENERGY EFFICIENT Lumen packages suitable for ceiling heights ranging from 8 to over 100 Efficacies up to 109 lm/w Superior-quality white LED light output using Chip on Board technology
More informationWARM COLOR DIMMING ARTIST SERIES 21º º º º - N/A 43º - N/A 60º K, 3000K or 3500K*** 3000K-1800K Warm Dim
Small aperture LED downlight with architectural appearance, featuring ELEMENT's unique patented high-low lamp positioning feature. The innovative design allows the LED to be positioned closer to the aperture
More informationEDGE EX33 3 x 3 Suspended Direct Linear
Project Name Date Type 3-1/4 (82.6mm) 3 x 3 Suspended Direct Linear 2-1/4 (57.2mm) 2-7/8 (73mm) Key Features 6063-T5 Extruded aluminum housing Highly reflective die-formed white painted reflector Wiring
More informationLuminaire PROFILE-SPOKE 15 UP 85 DN LED (PS1-D) Type. Notes. Performance Summary D OPTIONS 3S A 28 W B 34 W C 44 W D 57 W
T F W 604.549.9379 604.549.9555 fluxwerx.com PROFILE - SPOKE Specification Data Luminaire PROFILE-SPOKE 15 UP 85 DN LED () Type Project Profile Spoke 3 (S3) Product Notes Profile Spoke 4 (S4) Performance
More information4DS 4.5 Downlight Square
CATALOG #: 4-1/2 5-1/2 TYPE: PROJECT: NEW CONSTRUCTION AND REMODEL FEATURES Tunable white from 2700K to 5000K CCT, minimum 80 CRI 4 inch aperture is unobtrusive in small scale spaces Square shape accentuates
More informationCapella 3. Project Name. Construction. Optical System. Product Applications
Product # Type Date Project Name Project Location Capella 3 Construction Housing and lens frame are constructed from heavy-duty low copper die-cast aluminum. Material is structurally rigid and uniformly
More informationFCW3043 ADA FCW3045 ADA FCW3042 ADA FCW3040 ADA
FCW3043 2.5 in FCW3045 2.3 in FCW3042 2.3 in FCW3040 2.2 in 120 www.fclighting.com *Consult website for updated specification sheets regarding detailed information and performance. FC Lighting, Inc. 2012.
More informationProject Name. 24 (609.6mm) 24 (609.6mm)
Project Name Date Type ARCHITECTURAL RECESSED LUMINAIRE 24 (609.6mm) 24 (609.6mm) 3 (76.2mm) Formed 20 gauge cold rolled steel housing Highly reflective die-formed white painted reflector Wiring access
More informationAvenue B. Grid Mount (Regress Trim Shown) Flush Lens. Drywall Flange (Regress Trim Shown) Narrow 3" slot LED with frosted satin lens.
LED corrugated regress trim solid regress trim flush lens DIMENSIONAL DATA Grid Mount (Regress Trim Shown) FEATURES Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid
More informationBavaria Downs. Chaska, MN. Lighting
Bavaria Downs Chaska, MN Lighting Jason Kinsella City View Electric, Inc. 14309 Lake Drive NE Columbus, MN 55025 Phone 651.659.9496 Fax 651.659.0905 cityviewelectric.com DESCRIPTION Lumark The Prevail
More information2" LED SPECIFICATIONS ADJUSTABLE DOWNLIGHT & WALL WASH
The ELEMENT " adjustable downlight boasts a.4" aperture and.75" ceiling cutout. Unique aiming/locking mechanism offers -45º tilt, 36º rotation, and ELEMENT's patented high-low lamp positioning. Flanged
More informationVINCI-LED Wall/Area/Flood Lighting
Job Information Type: VINCI-LED Catalog #: Project: Comments: Prepared by: YEAR WARRANTY WARRANTY TEN INCLUDES LABOR ALLOWANCE Vinci Vinci Large 7⅞ ¼ ⅝ 9¾ ½ ⅛ Applications Wall/Surface Post/Bollard Low
More informationProject Name. 24 (609.6mm)
2x4 Project Name Date Type ARCHITECTURAL RECESSED LUMINAIRE 48 (1,219.2mm) 3 (76.2mm) 24 (609.6mm) Formed 20 gauge cold rolled steel housing Highly reflective die-formed white painted reflector Wiring
More informationavenue led features dimensional data performance Narrow 3" slot LED with frosted satin lens.
led features Narrow 3" slot LED with frosted satin lens. Shielding options include corrugated or solid regressed trim or flush lens. Avenue B LED allows ceiling tiles to rest on fixture rails, keeping
More informationGE Lighting. Heavy Industrial High Bay & Low Bay Lighting. (ABR1 - Series) imagination at work
GE Lighting Albeo LED Luminaire Heavy Industrial High Bay & Low Bay Lighting (ABR1 - Series) imagination at work Product Features The Albeo ABR1-Series is an IP66 rated fixture for demanding industrial
More informationEvolution Outline RECESSED LINEAR PERIMETER OUTLINE SLOT SYSTEM
Evolution Outline Project Name Date Type RECESSED LINEAR PERIMETER OUTLINE SLOT SYSTEM 4-1/2 (114.3mm) 5-1/4 (133.4mm) LED Product Partner Extruded aluminum trim with formed cold rolled 20 gauge steel
More information