2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan)
|
|
- Suzan Horn
- 6 years ago
- Views:
Transcription
1 2007-UP NAVIGATION INTERFACE MODULE (Infiniti/Nissan) ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS PRODUCT. INSTALL AND USE THIS PRODUCT AT YOUR OWN RISK. IF YOU DO NOT AGREE TO THESE TERMS DO NOT ATTEMPT TO INSTALL THIS PRODUCT. THIS PRODUCT HAS BEEN TESTED FOR NISSAN APPLICATIONS ONLY. IMPROPER INSTALLATION CAN RESULT IN IRREVERSABLE DAMAGE TO YOUR VEHICLE OR THIS MODULE. IT IS THE INSTALLERS RESPONSIBILITY TO VERIFY ALL WIRES PRIOR TO MAKING ANY CONNECTIONS. INSTALLATION: KPtechnologies Navigation Bypass module is designed to automatically press the OK button each time the vehicle is started and to allow programming the navigation/media system while the vehicle is in motion. The OK screen is processed electronically by soldering two wires of the KPtechnologies module directly to the navigation systems circuit board. This KPtechnologies module ONLY works on systems that utilize a (-) switching matrix. To program while in motion the module uses a standard Bosch style SPDT relay to break the Vehicle Speed Sensor (VSS) signal. While the signal is broken the navigation/media unit can be operated as if the vehicle was not moving. For safety reasons even with this module installed the AUX video input still will NOT work while the vehicle is in motion. ELECTRICAL CONNECTIONS: Due to the harsh environment found in vehicles, KP Technologies recommends always soldering and securely taping EVERY connection. 1. YELLOW 12VDC SWITCHED ACCESSORY a. Connect this wire to a source that reads 0 volts when the car is off and 12 volts when the ignition switch is on. 2. BLACK GROUND a. Connect this wire to ground. 3. PURPLE REVERSE INPUT (SPECIFIC VEHICLES ONLY) a. Connect this wire to the reverse light signal that meters 12vdc only when the vehicle is in reverse. This is only required for vehicles with OEM cameras that display on the navigation screen when the vehicle is in reverse. This input prevents the module from outputting the OK signal while the camera is on. 4. GREEN (OPTIONAL) SPEED SENSOR INTERRUPT
2 a. This 200mA output is triggered by pressing and holding the OK button for more then 1 second. This output can function in one of three programmable ways. Please see the PROGRAMMING section of this manual for more information. 5. TWISTED BLACK OK BUTTON INPUT a. Connect this wire directly to the circuit board on one side of the physical OK button. 6. TWISTED RED OK BUTTON INPUT a. Connect this wire directly to the circuit board on the other side of the physical OK button. NOTE: After the twisted black and red wires are connected to the circuit board an ohm meter can be used to verify functionality. The ohm meter, when measuring from the twisted black wire to the twisted red wire, with power disconnected, should read infinite resistance when the OK button is not pushed and should read near 0 ohms when the OK button is pushed Infiniti G35 Sedan Wiring Information (Please consult factory service manual for other models/years): Switched Ignition Purple (Main connector on back of radio brain) VSS Gray (Main connector on back of radio brain) Ground Black (Main connector on back of radio brain) OK button connections Solder the KPtechnologies twisted black and twisted red wire to the pins marked in the picture below at the main connector on circuit board that OK button is physically located. RELAY CONNECTIONS: Pin numbers can be found on the bottom of the relay once removed from the socket. For information about other applications please consult the KPtechnologies support forum. Pin 85 (+) Coil Connect to switched 12vdc power source Pin 86 (-) Coil Connect to KPtechnologies GREEN wire (AUX Output) Pin 30 Contact Common Application specific Pin 87A Contact Normally Closed Application specific 2
3 Pin 87 Contact Normally Open Application specific Common Applications: 1. VSS Bypass: Allows signal to pass only when the output is off. VSS wire must be cut and wired through relay. Pin 87 is not used in this application: 2. AUX Output: Voltage is passed only when the output is on. Voltage can be + or -. Pin 87a is not used in this application. SETTING: This modules delay time before processing the OK screen is adjustable between ~1 and ~30 seconds, with a ~30 millisecond resolution. This delay time will dictate how long the module waits after power is applied before it will output the electronic signal to automatically process the OK button. With the adjustment knob turned completely counter clockwise the delay will be set to ~1 second. With the adjustment knob turned completely clockwise the delay will be set to ~30 seconds. When programming this value it is recommended that you allow the OK screen to be displayed for at least 1 second before the OK button is processed for the best performance.. 3
4 PROGRAMMING: The AUX output can be programmed to operate in three different modes On/Off, Memory On/Off, and VSS Bypass. On/Off (Mode 1) Every time the AUX output is triggered the output will alternate states. When the car is first started this output will always be off. Memory On/Off (Mode 2) Every time the AUX output is triggered the output will alternate states. When the car is first started the output will revert to the state it was in when the ignition was last shut off. VSS Bypass (Mode 3) Triggering the AUX output will cause the output to turn on for 20 seconds. However, while the output is on each time the OK button is pushed the 20 second countdown timer will be reset back to 20 seconds. This allows the VSS signal to be bypassed as long as information is being programmed in to the navigation unit. Once data entry ceases the AUX output will automatically shut off as soon as the timer expires. To change the programmed state you must hold the OK button down for approximately 15 seconds. Once the button has been held down long enough the AUX output will pulse on and off 4 times to provide indication that programming mode has been entered. It is recommended to hook a relay up to the AUX output before attempting to program the unit, as the relay contacts will click each time the AUX output is energized providing audible feedback. Once program mode has been entered each time the OK button is pressed and released the mode will increment by 1 ( ) and the AUX output will pulse to indicate which mode is currently selected (1 pulse for Mode 1, 2 pulses for Mode 2, and 3 pulses for Mode 3). When the desired mode has been selected wait 10 seconds for the program mode to time out. Once program mode times out the new value will be stored to memory. If you turn the ignition off before program mode times out the value will not be stored. NOTE: For the sake of clarity the wire colors listed above are not shown in actual order. Please refer to the wire colors in the diagram and ignore the wire position. TROUBLESHOOTING: 4
5 For installation questions or concerns, please contact KPtechnologies at or visit us at For product information, please visit our website at 5
SPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL
SPEED SHIFT/TWO-STEP MODULE INSTALLATION MANUAL ALTHOUGH THIS PRODUCT HAS BEEN THOROUGHLY TESTED KPIERSON TECHNOLOGIES ASSUMES NO RESPONSIBILITY FOR ANY DAMAGE THAT MAY RESULT BY THE INSTALLATION OF THIS
More informationQUICK INSTALLATION GUIDE
MANUAL/AUTOMATIC T R A N S M I S S I O N 2 - B U T T O N R E M O T E S T A R T E R W I T H V I R T U A L T A C H S Y S T E M ( A S P R G - 1 0 0 0 C O M P A T I B L E ) QUICK INSTALLATION GUIDE Manual
More informationINSTALLATION GUIDE Table of Contents
CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2
More informationDLKEK3HN INSTALLATION INSTRUCTIONS
DLKEK3HN INDEX: INSTALLATION INSTRUCTIONS WIRING INSTRUCTIONS... PG 2-5 LED STATUS INDICATOR... PG 6 VALET/OVERRIDE BUTTON... PG 6 SHOCK SENSOR... PG 7 PROGRAMMABLE JUMPER-PINS... PG 7 PROGRAMMING REMOTE
More informationRS-900 / RS-901 SERIES VII
RS-900 / RS-901 SERIES VII OPERATING INSTRUCTIONS **IMPORTANT NOTES:- FOR RS901 MODEL ONLY** RS901 Model is an add-on/expansion unit, without remotes or an antenna that must be controlled by an existing
More informationMD10. Engine Controller. Installation and User Manual for the MD10 Engine Controller. Full Version
MD10 Engine Controller Installation and User Manual for the MD10 Engine Controller. Full Version File: MartinMD10rev1.4.doc May 16, 2002 2 READ MANUAL BEFORE INSTALLING UNIT Receipt of shipment and warranty
More informationFM SECURITY AND REMOTE START SYSTEM
FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with
More informationCT-5472 TW. Installation Guide REMOTE STARTER WITH FULL ALARM SYSTEM AND VIRTUAL TACH SYSTEM TWO-WAY LCD AUTOMATIC/MANUAL TRANSMISSION
TWO-WAY LCD AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER WITH FULL ALARM SYSTEM AND VIRTUAL TACH SYSTEM (AS PRG-1000 COMPATIBLE) CT-5472 TW Installation Guide Notice The manufacturer will accept no responsibility
More informationUSER MANUAL AND INSTALLATION GUIDE TIMER DELAY IN SECONDS SHIFT STYLE & SHIFT COUNTER TIMER DURATION NOS DELAY TIME IN SECONDS NOS START PERCENT
SCHNITZ MOTORSPORTS DSC-TG0- "TOP-GAS " IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE COIL, (OPTIONAL) GA YELLOW, PAGE COIL, NEGATIVE GA WHITE, PAGE SHIFT LIGHT GROUND 0GA BROWN, PAGE 0 SHIFT
More informationCT-3471 TW. Installation Guide TWO-WAY LCD AUTOMATIC/MANUAL WITH VIRTUAL TACH SYSTEM TRANSMISSION REMOTE STARTER (AS PRG-1000 COMPATIBLE)
TWO-WAY LCD AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER WITH VIRTUAL TACH SYSTEM (AS PRG-1000 COMPATIBLE) CT-3471 TW Installation Guide Notice The manufacturer will accept no responsibility for any electrical
More informationTIP SHEET T0937. Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT
Installation Tips For RS00/PS00 + ADS-TBSL-PL + SPDT TIP SHEET T0937 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to do-it-yourself installers
More informationRed #22 Power. Red #14. Brown #18. Ign/Acc/Start. White#14. Tachometer Foot-Brake Door Pin Pos Trunk/Hatch (open) (-) while running Lock Arm
E400 RFK1004 WIRING / CONNECTION GUIDE AUTOMATIC & MANUAL TRANSMISSION REMOTE STARTER & ALARM QUICK INSTALLATION GUIDE GUIDE # 69151 Power (utility) Red #22 OUTPUT INPUT Power Red #14 1 Yellow #14 Starter
More informationWIRING / CONNECTION GUIDE (20-PIN) SECONDARY CONNECTOR
EVO-ONE WIRING / CONNECTION GUIDE (20-PIN) SECONDARY CONNECT (6-PIN) BYPASS RELAY (+) Foot Brake Black IN 750mA (-) Parking lights Pink OUT 750mA (-) Trunk Release/AUX Yellow/Black OUT (-) Hand Brake Brown/
More informationINSTALLATION INSTRUCTIONS
Toyota 24-pin Dual Camera Blind Spot Monitoring System (Kit # 9002-2911) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 2 Adjustable
More informationSCHNITZ MOTORSPORTS PNC-202, 2-STAGE PROGRESSIVE NITROUS CONTROLLER USER MANUAL AND INSTALLATION GUIDE NOS PULSE FREQUENCY
SCHNITZ MOTORSPORTS PNC-202, 2-STAGE PROGRESSIVE NITROUS CONTROLLER USER MANUAL AND INSTALLATION GUIDE NOS #2, FUEL SOLENOID(GROUND) 1GA PURPLE, PAGE 14 NOS #2 NITROUS SOLENOID(GROUND) 1GA PURPLE, PAGE
More informationLt.Blue/Black. White. Orange. LED Blue LED Yellow LED Red
EVO-ONE RFK1004 WIRING / CONNECTION GUIDE (20-PIN) SECONDARY CONNECT (6-PIN) BYPASS RELAY (+) Foot Brake Black IN 750mA (-) Parking lights Pink OUT 750mA (-) Trunk Release/AUX Yellow/Black OUT (-) Hand
More informationSTANDARD AND GROUND SWITCHED APPLICATIONS
SNOWDOGG LIGHT REFERENCE STANDARD AND GROUND SWITCHED APPLICATIONS GENERAL REFERENCE SNOWDOGG LIGHT REFERENCE GENERAL REFERENCE 3 TROUBLESHOOTING GUIDES/PROCEDURES 6 CONNECTOR REFERENCE 12 ADAPTER HARNESS
More informationINSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit
R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;
More informationApplication Engineering
Application Engineering February, 2009 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital Compressor
More informationInstallation Manual By Firstech LLC, Version: 1.1
Installation Manual By Firstech LLC, Version: 1.1 Applicable to the following remote start system: CS600-S This device complies with Part 15 of the FCC rules. Operation is subject to the following conditions;
More informationADD-ON REMOTE STARTER TO AFTERMARKET SYSTEM
MEGATRONIX RS 110 ADD-ON REMOTE STARTER TO AFTERMARKET SYSTEM Installation and Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. RS110 ADD-ON REMOTE CAR STARTER For Vehicles Equipped With Automatic Transmission
More informationPhillips Permalogic Trailer Dome Lamp Controller Technical Bulletin
SERVICE BULLETIN NO. SB-17-014 Issue Date: 07/05/06 SUBJECT: Phillips Permalogic Trailer Dome Lamp Controller Technical Bulletin Phillips Industries has released a technical bulletin related to installation
More informationVS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1
VS 315 DELUXE 4-CHANNEL MOTORCYCLE ALARM Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 315 1 VS 315 2 INSTALLATION We recommend insulating all your soldered or crimped connections
More information2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE
REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause
More information2009 Maxima w/navigation Installation of KP Technologies Navigation Bypass Interface
2009 Maxima w/navigation Installation of KP Technologies Navigation Bypass Interface The following installation procedure will aid you in installing the KP Technologies Navigation Bypass Interface Module
More informationRS900 / RS901 SERIES VI
RS900 / RS901 SERIES VI OPERATING INSTRUCTIONS **IMPORTANT NOTES:- FOR RS901 MODEL ONLY** RS901 Model is an add-on/expansion unit, without remotes or an antenna that must be controlled by an existing alarm
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationINSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.
INSTALLATION MANUAL SL- 3 3-Channel Security with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty information:
More informationMethod statement: Setting the Vibration Cutout Switch
Method statement: Setting the Vibration Cutout Switch This Method statement is to be followed, in order to correctly set the Vibration Cutout Switch. Reset button Reset coil supply voltage Sensitivity
More informationChevy Equinox / GMC Terrain 2013-up (with color display) G
INSTALLATION INSTRUCTIONS FOR PART 99-3308G Chevy Equinox / GMC Terrain 2013-up (with color display) 99-3308G KIT FEATURES ISO DIN radio provision with pocket ISO DDIN radio provision Painted gray to match
More informationInstallation Manual By Firstech LLC, Version: 1.1
Installation Manual By Firstech LLC, Version: 1.1 Applicable to the following remote start system: CM800-S Auto Only Starter Control Module This device complies with Part 15 of the FCC rules. Operation
More informationINSTALLATION GUIDE. FCC ID NOTICE
REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This
More informationINSTALLATION MANUAL. Remote Mobile Security System. Model: PL30
Remote Mobile Security System INSTALLATION MANUAL Model: PL30 Copyright 1998 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be
More informationHP21 SERVICE SUPPLEMENT UNIT INFORMATION. TSC6 Two-Speed Control
SERVICE UNIT INFORMATION SUPPLEMENT HP21 Corp. 9426 L10 Litho U.S.A. All HP21-4 and -5 units (single and three phase) are equipped with a TSC6 two-speed control. The TSC6 (A14) two-speed control contains
More information535T Window Automation System
535T Window Automation System Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained
More informationUSER MANUAL AND INSTALLATION GUIDE ENGINE RPM AND NOS SHIFT COUNTER NOS DELAY TIME IN SECONDS NOS START PERCENT NOS FINAL PERCENT
SCHNITZ MOTORSPORTS DSC-9PS "PRO-STREET" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE SHIFT LIGHT POSITIVE PAGE 2 SHIFT LIGHT GROUND PAGE 2 NOS SOLENOID GROUND 1GA ORANGE, FUEL SOLENOID GROUND
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationRS-1604TW1/RS-1704TW2/RS-1804FM RS1905FM DP SERIES II (Data Port)
RS-1604TW1/RS-1704TW2/RS-1804FM RS1905FM DP SERIES II (Data Port) 2-Way Paging Remote Engine Starting & Keyless Entry System with 1-Way Sidekick Remote Control OPERATING INSTRUCTIONS *IMPORTANT INFORMATION:
More informationSRC. An Outdoor Reset Control for Sub-Atmosphere Steam Systems OUTDOOR TEMPERATURE
SRC STEAM RESET CONTROL An Outdoor Reset Control for Sub-Atmosphere Steam Systems Heat-Timer s theory of steam reset heating is as follows: Pulse the valve open to a limited valve position, very slowly
More informationApplication Engineering
Application Engineering March 2011 Copeland Digital Compressor Controller Introduction The Digital Compressor Controller is the electronics interface between the Copeland Scroll Digital compressor or the
More informatione-ask electronic Access Security Keyless-entry
e-ask electronic Access Security Keyless-entry Multiplex System Multiplex System Installation & Instructions (UM15 ~ 22272-03) Table of Contents Introduction... 1 Standard e-fob Operation and Features...
More informationSERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL
SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location
More informationRS-351-EDP. Installation Guide
RS-351-EDP Keyless Entry & Remote Start Installation Guide June 25, 2013 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin Main Wire Harness...
More informationREC-11+ REMOTE RECEIVER UNIT
Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous
More informationRemote Start with Keyless Entry Installation Guide ca5054
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide ca5054 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...3 Wire Connection Guide...4
More informationTIP SHEET. Installation Tips for your RS IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14. 1 P a g e
Installation Tips for your RS-150 + IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14 TIP SHEET Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts
More informationIdle Timer Controller - ITC Freightliner MT45 Contact InterMotive for additional vehicle applications
An ISO 9001:2008 Registered Company System Operation Idle Timer Controller - ITC805 2013-2018 Freightliner MT45 Contact InterMotive for additional vehicle applications The ITC805 system shuts down idling
More informationES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller.
ES52 Auto Start Engine Controller Installation and User Manual for the ES52 Auto Start Engine Controller. Full Version File: ES52rev2.63.doc October 24, 2006 2 Thank You For Purchasing This DynaGen Product
More informationGCU-10. Automatic Engine Control Unit Operators Manual
GCU-10 Automatic Engine Control Unit Operators Manual KUTAI ELECTRONICS INDUSTRY CO., LTD. TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw Headquarters : No.3, Lane 201, Chien Fu St.,
More informationNote: For all general information, refer to Installation and Instruction Manual supplied with the operator.
Installation & Instructions Manual Adding a Timer to Close on a single & 3-phase 115/230/208/460/575V. (Opera series & models MTH/MTBH/GH/MGH/MSJ/MJH/MGT/MSLD/MGSLD) operators Note: For all general information,
More information! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to oven before servicing, unless testing requires power.
Technical Information Double Oven Electric Range MER6555AAB/Q/W MER6751AAB/Q/S/W MER6755AAB/Q/S/W MER6775AAB/F/N/Q/S/W Due to possibility of personal injury or property damage, always contact an authorized
More informationMEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1
MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation Manual MEGATRONI CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 INSTALL 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10
More informationSCHNITZ MOTORSPORTS USER MANUAL AND INSTALLATION GUIDE PRO-MOD BATTERY VOLTS DIAGNOSTICS NOS PULSE FREQUENCY NOS DELAY TIME IN SECONDS
SCHNITZ MOTORSPORTS DSC-CS "PRO-MOD" IGNITION CONTROLLER USER MANUAL AND INSTALLATION GUIDE COIL, (OPTIONAL) GA YELLOW, COIL, NEGATIVE GA WHITE, GA BLACK, SHIFT LIGHT +V OUTPUT PAGE 0 NOS ACTIVATION INPUT
More informationRetains OnStar/OE Bluetooth Adjustable volume for chimes and OnStar Retains satellite radio Retains balance and fade Micro B USB updatable
GMOS-LAN-034 INSTALLATION INSTRUCTIONS INTERFACE FEATURES Provides accessory power (12-volt 10-amp) Maintains the retained accessory power (R.A.P.) feature Can be used in non-amplified, or amplified models
More informationMODEL RMS INSTALLATION INSTRUCTIONS. CONTENTS Page A. Introduction 1. Usage 2 2. How it operates 2
CONVEYOR COMPONENTS COMPANY Division of Material Control, Inc. 130 Seltzer Road, PO Box 167 Croswell, MI 48422 USA PHONE: (810) 679-4211 TOLL FREE (800) 233-3233 FAX: (810) 679-4510 Email: info@conveyorcomponents.com
More informationInstallation Instructions
BZ-200, BZ-250, BZ-250-347 Power Pack Auto/Manual Mode Switch BZ-250, BZ-250-347 only SPECIFICATIONS Voltages BZ-200, BZ-250... 120 277 VAC, 50/60 Hz, single phase BZ-250-347... 120 347 VAC, 50/60 Hz,
More informationRemote Start Installation Guide CA 4051
PROFESSIONAL SERIES Remote Start Installation Guide CA 4051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Before You Begin... 3 Wire Connection Guide... 4 4 Pin Main Harness... 5 3 Pin
More informationJeep Cherokee Latitude/Limited 2014-up
Installation instructions for part 99-6526 REV. 5/23/2017 INST99-6526 KIT FEATURES ISO DDIN radio provision Included interface shows climate and menu info on the aftermarket radio screen. Painted scratch-resistant
More informationMM1 Installation Instructions
MM1 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or
More informationGMOS-05 Installation Instructions
GM ONSTAR CLASS II DATA BUS INTERFACE GMOS-05 Installation Instructions The GMOS-05 is designed to be used in vehicles listed below to retain Onstar and the warning chimes that are lost when the OEM radio
More informationAdvanced Instructions
Advanced Instructions Detailed wiring and installation instructions Monitor Battery #1 (and power the device) Connect the long red (positive) and black (negative) leads to the main battery. Many vehicles
More informationGMOS-LAN-012. GM LAN-29 Data Interface 2006-up* *Visit AxxessInterfaces.com for up-to-date vehicle specific applications.
GMOS-LAN-012 INSTALLATION INSTRUCTIONS INTERFACE FEATURES Provides accessory power (12-volt 10-amp) Maintains the retained accessory power (R.A.P.) feature Can be used in non-amplified, or analog/digital
More informationRemote Start with Keyless Entry Installation Guide CA 5051
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA 5051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More informationINSTALLATION INSTRUCTIONS
Toyota 24-pin Dual Camera Blind Spot Monitoring System (Kit # 9002-2911) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: 2 Adjustable
More informationINSTALLATION INSTRUCTIONS
Multi Camera Interface (Kit # 9002-6118) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Interface module Video input harness These
More information# Traction Control Window Switch
1 INSTRUCTIONS # 82085 Traction Control Window Switch Thank you for choosing products; we are proud to be your manufacturer of choice. Please read this instruction sheet carefully before beginning installation,
More informationINSTALL GUIDE DIR-CH(RS)-CH8-[FLRSCH10]-EN
INSTALL GUIDE DOCUMENT NUMBER 870 REVISION DATE 080 FIRMWARE DIR-CH(RS)-CH8-[FLRSCH0] HARDWARE FLRSCH0 ESSORIES FLPROG (REQUIRED) DIRECTED XL-0 RF-KIT & ADS-HRN(RS)-XL0 (OPTIONAL) DIRECTED SMART & ADS-HRN(RS)-SM0
More informationInstallation Guide TWO-WAY LED AUTOMATIC TRANSMISSION REMOTE STARTER
TWO-WAY LED AUTOMATIC TRANSMISSION REMOTE STARTER Installation Guide W A R N I N G! This is a generic installation guide and it is designed for the specific model number stated above. Furthermore, for
More information! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless testing requires power.
Electric Freestanding Range Technical Information MER5875RA* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. Refer
More informationINSTALL GUIDE FLC-NI(RS)-NI6-[FLRSNI5]-EN
INSTALL GUIDE FLC-NI(RS)-NI-[FLRSNI]-EN DOCUMENT NUMBER REVISION DE 000 FIRMWARE FLC-NI(RS)-NI-[FLRSNI] HARDWARE FLRSNI ACCESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) CARLINK ASCL (OPTIONAL) NOTICE The
More informationNote: Read this manual carefully before installing the operator and place this installation manual in an accessible place near the operator.
Installation & Instruction Manual Electronic Control Board (ECB) Note: Read this manual carefully before installing the operator and place this installation manual in an accessible place near the operator.
More informationINSTALLATION MANUAL. Model: PLUS Vehicle Security
R Vehicle Security INSTALLATION MANUAL Model: PLUS-5000 Copyright 1999 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered
More informationPIM701 (Police Interface Module) Dodge Charger Pursuit
An ISO 9001:2008 Registered Company PIM701 (Police Interface Module) 2015-2017 Dodge Charger Pursuit Introduction The Police Interface Module is intended to provide Dodge Chargers with multiple desired
More information! WARNING To avoid risk of electrical shock, personal injury or death; disconnect power to range before servicing, unless testing requires power.
Double Oven Electric Range Technical Information MER6765BA* Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or repair of this unit. Refer
More informationINSTALLATION INSTRUCTIONS
Dual Camera Blind Spot Monitoring System w/multi-camera Switcher (Kit # 9002-2904) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit:
More informationService Manual for Battery Control Center
Service Manual for Battery Control Center P/N 82 E0071 00 (Ref. 81 1317) June, 1999 Battery Control Box Operation Charging Circuit This function charges the coach battery from the engine alternator while
More informationUser Guide TWO-WAY LED AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER WITH FULL ALARM SYSTEM
TWO-WAY LED AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER WITH FULL ALARM SYSTEM User Guide WARNING It is the responsibility of the vehicle operator to ensure their vehicle is parked in a safe and responsible
More informationINSTALLATION INSTRUCTIONS FOR PART TRIGGER TRIGGER
6 2.5 1.5 ISO M4 M5 M3 WIRE CUTTER INSTALLATION INSTRUCTIONS FOR PART TRIGGER TRIGGER The Trigger is a universal module that provides 15 different preset functions that are activated from a positive or
More informationVLP-UL-KIT INSTALLATION INSTRUCTIONS. The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 &
Solenoid VLP-UL-KIT INSTALLATION INSTRUCTIONS The VLP-UL-KIT for 36 or 48 is a field installable solenoid latch pullback for the Von Duprin 33/35 & 98/99 series exit devices..050 Hex Wrench retraction
More informationECO3-601/602 EcoStar III * Chevy Express/GMC Savana Contact Intermotive for additional vehicle applications
An ISO 9001:2015 Registered Company ECO3-601/602 EcoStar III 2009-2019* Chevy Express/GMC Savana Contact Intermotive for additional vehicle applications * In 2017-2018, the ignition switches on Chevy Express
More informationVEHICLE SECURITY SYSTEM INSTALLATION MANUAL
VEHICLE SECURITY SYSTEM WITH REMOTE START & NETWORK INTERFACE INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before You Begin This system is intended
More informationC-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit
An ISO 9001:2008 Registered Company C-PIM701 (Police Interface Module) 2018 Dodge Charger Pursuit Introduction The Police Interface Module is intended to provide Dodge Chargers with multiple desired functions
More informationGM ONSTAR LAN DATA BUS INTERFACE GMOS-LAN-01. Installation Instructions
GM ONSTAR LAN DATA BUS INTERFACE GMOS-LAN-01 Installation Instructions Not compatible with amplified sound systems * READ IMPORTANT WARNING ON PAGE 1 BEFORE ATTEMPTING ANY INSTALLATION The GMOS-LAN-01
More informationINSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC).
P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com ALPHA-3v2 Electronic Speed Controller Supplied for
More informationGMOS-06 INSTALLATION INSTRUCTIONS
CADILLAC ONSTAR CLASS II DATA BUS INTERFACE GMOS-06 INSTALLATION INSTRUCTIONS * READ IMPORTANT WARNING ON PAGE 1 BEFORE ATTEMPTING ANY INSTALLATION The GMOS-06 is designed to be used in Cadillacs equipped
More informationTIP SHEET. Installation Tips for RS00 + FD-1 (T-harness) + PASS-3 + SPDT T3126 v1.0 5/13/14
TIP SHEET Installation Tips for RS00 + FD-1 (T-harness) + PASS-3 + SPDT T3126 v1.0 5/13/14 Ford: (2002 Crown Victoria), (2000-2002 Excursion), (1997-2002 Expedition), (1998-2001 Explorer), (1997-2003 F-150),
More informationFOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES
#STARTC2003-TW TWO-WAY FM/FM REMOTE CONTROL VEHICLE STARTER & ALARM SYSTEM INSTALLATION GUIDE FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES THIS UNIT MUST BE INSTALLED BY AN AUTHORIZED MICRO ALARM
More informationModel 2100 Installation Guide
Model 2100 Installation Guide 2001 Directed Electronics, Inc. Vista, CA N2100 4-01 Rev. N/C 1.1 table of contents What Is Included..................... 2 Wiring Quick Reference Guide............ 3 Primary
More informationRemote Start Installation Guide ca 4552
PROFESSIONAL SERIES Remote Start Installation Guide ca 4552 ca4552. 2011 Audiovox Electronics Corporation. All rights reserved. 1 Before You Begin... 3 Wire Connection Guide... 4 4 Pin Main Harness...
More informationINSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC).
P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com TABLE OF CONTENTS PROVIDED IN INSTRUCTIONS. Page
More information! WARNING To avoid risk of electrical shock, personal injury, or death, disconnect power to range before servicing, unless testing requires power.
Electric Freestanding Range Technical Information AER5712BA* MER5751BA* MER5752BA* MERH752BA* MERM752BA* Due to possibility of personal injury or property damage, always contact an authorized technician
More informationRS2-G3 ONE BUTTON 2-WAY REMOTE START SYSTEM
RS2-G3 ONE BUTTON 2-WAY REMOTE START SYSTEM INSTALLATION INSTRUCTIONS CONGRATULATIONS on your choice of a Cool Start System with Data Port Technology for direct connection to bypass module by Crime stopper
More informationModel 2300DL Installation Guide
Model 2300DL Installation Guide POWER ACCESS CORPORATION 4 HERSHEY DRIVE, DOCK 4 ANSONIA, CT 06401 800-344-0088 WEBSITE: www.power-access.com EMAIL: salesinfo@power-access.com 1 STANDARD PARTS MODEL 2300DL
More informationINSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN
INSTALL GUIDE DOCUMENT NUMBER 89 REVISION DATE 707 FIRMWARE COM-CH(RS)-CH-[FT-CH-DC] HARDWARE FT-CH-DC ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) NOTICE
More informationINSTRUCTIONS. DO NOT CONNECT TO MAINS POWER ( V AC).
P.O Box 578 Casino, NSW, 2470 Australia Phone: International ++614 2902 9083 Australia (04) 2902 9083 Website: http://rcs-rc.com E mail: Info@rcs-rc.com TABLE OF CONTENTS PROVIDED IN INSTRUCTIONS. Page
More informationINSTRUCTIONS. 20 Circuit Wiring Kit Instructions October 2009, Speedway Motors, Inc.
1 MAIN FUSE PANEL The main fuse panel harness s designed to be mounted under the dash a the firewall in an area close to the steering column. The enclosed representation of the main dash harness shows
More informationCS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet
More informationINSTALLATION INSTRUCTIONS
Backup Camera Interface (Kit # 9002-7762) Please read thoroughly before starting installation and check that kit contents are complete. Items Included in the Kit: Cam T-Harness Plug & Play I/O T-Harness
More informationSM361 RIG SWITCH CONSTRUCTION MANUAL
SM361 RIG SWITCH CONSTRUCTION MANUAL Document ver 1, For software release ver 1.1 May 27, 2016 Controls the power of 12V equipment while a vehicle is in use Product Development by: SM361 RIG SWITCH OVERVIEW
More information12V PROGRAMMABLE POWER OUT
Page 1 ACCESSORIES STARTER IGNITION BATTERY WIRES SIDE VIEW BLUE RED YELLOW 30 A 10 A BLUE / WHITE YELLOW WHITE / BLUE WHITE / DOOR TRIGGER See opt. 16 DOOR TRIGGER (input positive) See opt. 16 PARKING
More information