2010 POLICE PREP PACKAGES

Transcription

1 2010 POLICE PREP PACKAGES OWNER S MANUAL (65A) BASE POLICE PREP PACKAGE (68P) COMPLETE POLICE PREP PACKAGE (Includes 65A components) (65P) BASE LIGHTING PACKAGE (Includes 65A) (65W) VISIBILTY PACKAGE (Includes 68P) (65U) READY FOR THE ROAD PACKAGE (See separate manual) Review owner s manual prior to package use. 9W7T-19A312-AA Rev. 0

2 TABLE OF CONTENTS Option Content 65A and 65P Packages Option Content 68P and 65W Packages... Option Content 65U Package. About Crown North America.... Police Prep and Visibility Packages... Base Police Prep Package..... Strobe Bulbs..... Console Wiring. Engine Compartment Wiring.. Trunk Wiring..... Headlight Flasher (Wig-Wag) Complete Police Prep Package Console Mounting Platform Center Wiring Conduit.... Hidden Manual Rear Door Lock Plungers..... Trunk Air Circulation Fan Permanent Rubber Tie-Down Strap... Dual Trunk Storage Boxes... Rear Communications Service Tray... Battery Saver Circuit & Vehicle Speed Signal Visibility Packages... Strobe Power Unit (65U and 65W).. Strobe Power unit for 65P.... Flashing Rear Deck LED Lights New Rear LED Deck Lights.. Switch Control Panel..... Schematics... Key to Wire Color Codes... Ford Engine Compartment Fuse Block... Power Connection Placement... Power Circuits Placement.... Power Circuits Placement.... Spare Circuit Placement.... Ground Circuits Placement.... Strobe Power Supply Assembly... Console Pin outs..... Alternating Headlight Flasher Circuit.... Horn/Siren Relay Amplifier Circuit (Amplifier at Console). Horn/Siren Relay Amplifier Circuit (Amplifier in Trunk)..... Glove Box Power Distribution Center... Trunk Power Distribution Center... Lighting Relay Center (8-Relay Panel)... Removal of Police Prep Packages. General Guidelines.... Technical Service Numbers..... SPECIAL NOTE: Although the total current capacity of the harness on the following pages states that the harness is capable of handling over 350 Amps of fused power, it is recommended that total vehicle loads to the 2010 Crown Victoria Police Interceptor be limited to 110 Amps, at idle, to support alternator/battery capacity. Electrical loads above this level may degrade battery/ starting capacity

3 OPTION CONTENT 65A and 65P Packages 2010 Ford Police Interceptor Equipment Packages The Base Package 65A Wiring Harness has increased to 350 amps of battery and ignition power. There should be no need for any additional wires to be connected to the battery with the added amperage in Customer feedback has been implemented and there have been improvements to the versatility and usability of the Base Package Harness. The revised Base Lighting Package 65P has been created to supply plug and play lighting components to the Base Package 65A maximizing police car identification and visibility. Base Package (65A) Base Lighting Package (65P) Two (2) Front Strobe Bulbs and Two (2) Rear Strobes, installed in marker light and taillight lenses. *Strobe Power Supply required to flash Strobe Bulbs. Wiring Harness including the following items: - Six (6) Strobe Cables - Shielded and Grounded pre-run to the front marker lights, taillights lenses and two (2) to the front grill. Strobe Cables are industry standard gender and color configuration for connection to customer supplied aftermarket Strobe Power Supplies. Glove Box Power Distribution Center 50 amps, fused in the engine compartment. Five (5) power and ground wires for customer use. Five (5) fuses - Two (2) battery and three (3) ignition powered. Trunk Power Distribution Center 50 amps, fused in the engine compartment. Five (5) power and ground wires for customer use. Five (5) fuses - Two (2) battery and three (3) ignition powered. *One ignition fuse position utilized by Options 65P / 65W / 65U amp battery circuit and ground accessible at console base only - 50 amp battery circuit and ground accessible at console base or trunk. Available in trunk from pigtail harness (utilized by Options 65W / 65U). - Two (2) 50 amp battery circuit and ground accessible at trunk only. Available in trunk from pigtail harness (utilized by Options 65W / 65U) amp battery circuit and battery ground accessible at console base or trunk, for radio communications amp ignition circuit accessible at trunk only. Available in trunk from pigtail harness (utilized by Options 65W / 65U). - Siren/speaker wiring pre-run to front of vehicle with waterpack connector. Available in trunk from pigtail harness (utilized by Ready for the Road Package 65U). - Two (2) Extra circuits pre-run to front of vehicle accessible at console or trunk. - Horn/siren relay circuit accessible at console base or trunk (utilized by Ready for the Road Package 65U). - Four (4) Extra circuits pre-run from the engine compartment to console base. One circuit is heavy gauge for additional battery or ground connection. - Four (4) Extra circuits pre-run from the console base to trunk. Alternating Headlight Flasher with control wire accessible at console for optional connection to customer supplied positive control switch box. Extra relay and control wire available for overriding alternating headlight flasher at night when headlights are in use. Strobe Power Supply, Six (6) outlets with front shut down. Additional control wire accessible at trunk for connection to customer supplied positive control switch box. *Required to flash strobe bulbs. Two High Intensity Flashing Rear Deck LED Lights, with matching interior color housings (Charcoal, Medium Light Stone, Light Camel). Red & Blue color configuration is standard. Additional control wire accessible at trunk for connection to customer supplied positive control switch box. Ford Warranty is 3 years / 36,000 miles on all components except the following: Strobe Lights 1 year (Front Marker Light & Taillight Strobes) Indicates included in option Indicates utilized by option and not available for customer use 3

4 OPTION CONTENT 68P and 65W Packages 2010 Ford Police Interceptor Equipment Packages The Complete Police Prep Package 68P is a hardware equipment package with model specific mounting solutions to provide end users with safe and secure police equipment. Please see the Police Modifier Guide for additional equipment mounting guidelines at The Visibility Package Option 65W is a package of lighting equipment to maximize police car identification and visibility. Complete Police Prep Package (68P) Visibility Package Option (65W) Two (2) Front Strobe Bulbs and Two (2) Rear Strobes, installed in marker light and taillight lenses. *Strobe Power Supply required to flash Strobe Bulbs. Wiring Harness including the following items: - Six (6) Strobe Cables - Shielded and Grounded pre-run to the front marker lights, taillights lenses and two (2) to the front grill. Strobe Cables are now industry standard gender and color configuration for connection to customer supplied aftermarket Strobe Power Supplies. Glove Box Power Distribution Center 50 amps, fused in the engine compartment. Five (5) power and ground wires for customer use. Five (5) fuses - Two (2) battery and three (3) ignition powered. Trunk Power Distribution Center 50 amps, fused in the engine compartment. Five (5) power and ground wires for customer use. Five (5) fuses - Two (2) battery and three (3) ignition powered. *One ignition fuse postion utilized by Options 65P / 65W / 65U amp battery circuit and ground accessible at console base only - 50 amp battery circuit and ground accessible at console base or trunk. Available in trunk from pigtail harness (utilized by Options 65W and 65U). - Two (2) 50 amp battery circuit and ground accessible at trunk only. Available in trunk from pigtail harness (utilized by Options 65W and 65U) amp battery circuit and battery ground accessible at passenger kick panel or trunk, for radio communications amp ignition circuit accessible at trunk only. Available in trunk from pigtail harness (utilized by Options 65W / 65U). - Siren/speaker wiring pre-run to front of vehicle with waterpack connector. Available in trunk from pigtail harness (utilized by Ready for the Road Package 65U). - Two (2) Extra circuits pre-run to front of vehicle accessible at console or trunk. - Horn/siren relay circuit accessible at console base or trunk (utilized by Ready for the Road Package 65U). - Four (4) Extra circuits pre-run from the engine compartment to console base. One circuit is heavy gauge for additional battery or ground connection. - Four (4) Extra circuits pre-run from the console base to trunk. Alternating Headlight Flasher with control wire accessible at console for optional connection to customer supplied positive control switch box. Extra relay and control wire available for overriding alternating headlight flasher at night when headlights are in use. Console Mounting Platform, secured using existing mounting points. The powder-coated aluminum mounting plate is predrilled for the addition of equipment. (Without Armrest) Center Wiring Conduit, 2" x 4" opening. For ease of installation, the conduit will house and protect any additional wire run from the center console to the trunk. Accommodates communication wires and connectors. Modified for Fire Suppression Hidden Manual Door Lock Plunger - located in both rear doors, forward door frame. Option disconnects rear locks and rear windows from operation (Option 948 can be ordered in conjunction to maintain window operation from driver and front passenger switches only). Trunk Air Circulation Fan, pulls air from passenger area and exhausts through trunk, stabilizing climate for equipment. Helps control moisture, dust and humidity. Grounded to reduce electro magnetic interference. Permanent Rubber Tie Down Strap, for securing trunk when carrying large items like a bicycle. Dual Trunk Storage Boxes, maximize trunk space and provide equipment mounts. Clear view covers for quick reference. Rear Trunk Communications Service Tray, slides on heavy-duty tracks. Shipped with secured spare tire. For equipment mounting. Strobe Power Supply, Six (6) outlets with front shutdown. Additional control wire accessible at trunk for connection to customer supplied positive control switch box. *Required to flash strobe bulbs. Two High Intensity Flashing Rear Deck LED Lights, with matching interior color housings (Charcoal, Medium Light Stone, Light Camel). Red & Blue color configuration is standard. Additional control wire accessible at trunk for connection to customer supplied positive control switch box. Visibility Switch Panel, including four (4) position slide switch and four (4) rocker switches. Controls strobes, flashing LED lights and alternating headlight flasher. Capable of controlling up to eight (8) light bar or other lighting functions. Installed with bracket to Console Mounting Platform. Lighting Relay Center, for use with the Visibility switch panel - fused at 150 amps delivered through eight (8) relays. Holds eight (8) fuses. Outputs accessible at trunk for connection of customer supplied lighting. Ford Warranty is 3 years / 36,000 miles on all components except the following: Strobe Lights 1 year (Front Marker Light & Rear Strobes Bulbs) 4

5 OPTION CONTENT 65U Package 2010 Ford Police Interceptor Equipment Packages A package of lighting and siren components with a selection of popular hardware to get your vehicles in service quickly. This turn key system Ready For is available from any Ford dealer in one easy step. The Ready for the Road Package is also programmable to offer greater flexibility. Finally The Road the guess work is taken out of mounting siren speakers and grill lights. Factory approved siren speaker and grill lights are installed in this Package package without compromising driver and occupant safety. (65U) Two (2) Front Strobe Bulbs and Two (2) Rear Strobes, installed in marker light and taillight lenses. Wiring Harness including the following items: - Six (6) Strobe Cables - Shielded and Grounded pre-run to the front marker lights, taillights lenses and two (2) to the front grill strobe lights. Strobe Cables are now industry standard gender and color configuration for connection to customer supplied aftermarket Strobe Power Supplies. Glove Box Power Distribution Center 50 amps, fused in the engine compartment. Five (5) power and ground wires for customer use. Five (5) fuses - Two (2) battery and three (3) ignition powered. Trunk Power Distribution Center 50 amps, fused in the engine compartment. Four (4) power and ground wires for customer use. Four (4) fuses - Two (2) battery and two (2) ignition powered amp battery circuit and ground accessible at console base only - Three (3) 50 amp battery circuit and ground, supplies Lighting Relay Center amp battery circuit and battery ground accessible at passenger kick panel or trunk, for radio communications amp ignition circuit, supplies Remote Siren Amplifier. - Siren/speaker wiring pre-run to siren speaker at front of vehicle with water pack connector. (utilized by Remote Siren Amplifier). - Two (2) Extra circuits pre-run to front of vehicle accessible at console or trunk. - Horn/siren relay circuit (utilized by Remote Siren Amplifier). - Four (4) Extra circuits pre-run from the engine compartment to console base. One circuit is heavy gauge for additional battery or ground connection. - Four (4) Extra circuits pre-run from the console base to trunk. Alternating Headlight Flasher, Extra relay and control wire for overriding alternating headlight flasher at night when headlights are in use. Console Mounting Platform, secured using existing mounting points. The powder-coated aluminum mounting plate is pre-drilled for the addition of equipment. (Without Armrest) Hidden Manual Door Lock Plunger - located in both rear doors, forward door frame. Option disconnects rear locks and rear windows from operation (Option 948 can be ordered in conjunction to maintain window operation from driver and front passenger switches only). Trunk Air Circulation Fan, pulls air from passenger area and exhausts through trunk, stabilizing climate for equipment. Helps control moisture, dust and humidity. Grounded to reduce electro magnetic interference. Rear Trunk Communications Service Tray, slides on heavy-duty tracks. Shipped with secured spare tire. For equipment mounting. Strobe Power Supply, Six (6) outlets with front shutdown. Two High Intensity Flashing Rear Deck LED Lights, with matching interior color housings (Charcoal, Medium Light Stone, Light Camel). Red & Blue color configuration is standard. Lighting Relay Center, for use with the Visibility switch panel - fused at 150 amps delivered through eight (8) relays. Holds eight (8) fuses. Outputs accessible at trunk for connection of customer supplied lighting. Lighting and Siren Controller, programmable with four position slide switch, 13 illuminated buttons and 5 siren tones. Installed with bracket to Console Mounting Platform. Mic Kit is not included. RJ11 Serial Cable, pre-run from console to trunk for connection between Lighting and Siren Controller and Remote Siren Amplifier. Remote Siren Amplifier, utilizes vehicle horn circuit for activating siren and changing tones. Radio rebroadcast inputs available in trunk. 50 watt siren output available in trunk for addition of second speaker. Common mic input available in trunk. Meets California Code of Regulations (CCR) Title 13, Article 5. Installed with bracket to rear trunk communications service tray. Two Grill Strobe Lights, installed with mounting brackets. Red & Blue color configuration is standard. 100 Watt Siren Speaker, with replaceable driver. Installed with mounting bracket. Sound output meets SAE J1849 and "Class A". 500ft audibility. Permanent Rubber Tie Down Strap, for securing trunk when carrying large items like a bicycle. Ford Warranty is 3 years / 36,000 miles on all components except the following: Strobe Lights 1 year (Front Marker Light & Taillight Strobes and Grill Strobes) Siren Components 2 years (Lighting and Siren Controller, Remote Siren Amplifier and Siren Speaker) 5

6 ABOUT CROWN NORTH AMERICA Crown has been in the business of manufacturing and installing commercial vehicle products for nearly 30 years. Crown currently has two plants in Canada and five plants within the United States, which together have delivered over 100,000 vehicles to commercial service providers. Crown has been a Tier 1 supplier to Ford Motor Company since A significant element of Crown s success is due to the ability to perform quick, high quality vehicle outfitting. This allows the vehicles to be entered into service use in a timely manner. High quality is supported by ISO standards. Manufacturing and assembling process controls assure that every Crown up-fitted vehicle meets and exceeds customer expectations. 6

7 POLICE PREP AND VISIBILITY PACKAGES The Ready for the Road Package (65U), Base Police Prep Package (65A), Base Lighting Package (65P), Complete Police Prep Package (68P), and Visibility Package (65W), are fully compliant with the United States Federal Motor Vehicle and Canadian Motor Vehicle Safety Standards. The Ready for the Road Package (65U), Base Police Prep Package (65A), Base Lighting Package (65P), Complete Police Prep Package (68P), and Visibility Package (65W) have undergone many tests as individual components and as completed assemblies. The components have been subjected to temperatures ranging from minus 40 to over 175 degrees Fahrenheit. All moving components, such as latches, tray slides, and switches have been put through tens of thousands of cycles. All packages, including the new Ready for the Road Package have been installed within a vehicle and subjected to an accelerated durability test that simulates 300,000 miles of use over various terrain and environmental conditions. The electrical systems must meet the most stringent requirements. All circuits have been load tested and certified. All power circuits have ground wires provided, which are grounded to Ford approved chassis grounds. All terminations have been power crimped. Use of the police specific wiring greatly reduces the risk of vehicle electrical system damage and can greatly increase the durability of other vehicle electrical components. The Ford warranty for the original electrical components is preserved and available for full-term warranty coverage, except where noted for siren speaker and strobe bulbs. 7

8 BASE POLICE PREP PACKAGE (65A) The Police Prep Packages are designed to promote speedy preparation of police vehicles for in-service use. The wiring harness in the Police Prep Packages supplies a police specific electrical system that is designed to provide easy access for fused power and ground circuits at the glove box, console area and trunk. Please note: The Base Police Package (65A) and Complete Prep Package (68P) do not come equipped with a strobe power supply. The Base Police Package and Complete Prep Package come equipped with six (6) shielded strobe cables, four (4) corner strobes and are ready for the installation of a customer supplied strobe power supply. The Base Lighting Package (65P), Complete Visibility Option (65W) or Ready for the Road Package (65U) come equipped with a six (6) head Strobe power supply with front shut down capability. 8

9 BASE POLICE PREP PACKAGE (65A) GLOVE BO POWER DISTRIBUTION CENTER Power sources - (color coded) See page 44. Grounds - (Black) See pages 36 CONSOLE AREA Extra wires to trunk & engine compartment. pages 34 and 35. Headlight activation (page 41), Speed Signal and Battery Saver Circuit. Three additional 50Amp Battery and Ground circuits, pages 30 and 31 Horn ring transfer circuit, and 2 spare circuits to Radiator, pages 41 and 42 9

10 BASE POLICE PREP PACKAGE (65A) FORD ENGINE COMPARTMENT FUSE BLOCK. See page 27. WIRES FOR SIREN AT RADIATOR, ROUTED TO CONSOLE AND TRUNK (color coded) see pages 42 and 43. Grill Strobe Connectors SPARE WIRES LOCATED ON PASSENGER SIDE WHEEL HOUSE, ROUTED TO CONSOLE AREA - (color coded) see page 41 10

11 BASE POLICE PREP PACKAGE (65A) TRUNK WIRING IDENTIFICATION Strobe Power Supply Leads (For use with 65W, 65P and 65U packages) See page 38 Trunk Power Distribution Center - see page 45. White Conn. YE/LG wires to horn ring - see pages 41 and Amp communications circuit - see pages 31 and 33 Red Connectors Strobes cables to tail lights, front marker lights and grill lights See page 38. Ground wires for Power Distribution Center. - (color coded) See page 37. Spare wires (color coded) 2 to radiator 4 to console see pages 34 and 35. Power wires from trunk Power distribution Center See page 45 11

12 BASE POLICE PREP PACKAGE (65A) Alternating Headlight Flasher An alternating headlight flasher module is included with each package which allows for the headlight high beams to alternate. To activate the headlight flasher in the Base Police Package (65A), Base Lighting Package (65P) and the Complete Prep Package (68P), use the LG/YE circuit available at the console. This wire should be connected to a B+ switch box. Visibility Option (65W) and Ready for the Road (65U), supplies a switch control panel at the console mounting platform that allows for the control of the headlight flasher and other Visibility Package components at the fingertips of the driver. Caution: Alternating headlight flashers must be used only on high beam to meet FMVSS and CMVSS standards. Please see the Ford Police Modifiers guide when connecting any flasher module to rear lights of the vehicle. Some jurisdiction have requirements that state that the headlight flasher must not operate with headlights on. The Prep Package harness system has a provision built into it to allow for this function. See schematic on page

13 COMPLETE POLICE PREP PACKAGE Console Mounting Platform Included with (68P), (65U) and (65W) The console mounting platform is designed to firmly support police consoles and equipment. The console mounting platform is made of heavy gauge steel and aluminum and is predrilled and tapped with ¼-20 threaded holes for easy mounting. Components should be torqued to 11.5 Nm.. Slots are provided for routing of electrical wiring and cables. 13

14 COMPLETE POLICE PREP PACKAGE Center Wiring Conduit Included with (68P) and (65W) The center wiring conduit allows for the routing of wires from the console to the rear communications service tray with only the removal of the rear seat cushion. For these units, both the seat cushion and seat back will have to be removed. The nylon conduit will need to be opened, have the wires inserted and then be closed. 14

15 COMPLETE POLICE PREP PACKAGE Hidden Manual Rear Door Lock Plunger Included with (68P), (65W) and (65U) This option reworks the rear doors of the vehicle so that the lock stem has been removed from the standard position and relocated to the front edge of the rear doors. This ensures that only an officer has access to the plunger of the lock. The power lock and power window connectors are taped to the harness within the rear doors. Disconnecting the white connectors in the door panel has disabled automated locks. They may be reconnected if normal power operation is desired. With this option, the rear windows have also been reworked to be inoperative from either the front or rear switches. If it is desirable to have the rear windows operational from the front switches, dealers should order Ford option

16 COMPLETE POLICE PREP PACKAGE Trunk Air Circulation Fan Included with (68P), (65W) and (65U) The trunk air circulation fan pulls air from the passenger compartment and exhausts through the trunk, which in turn helps to stabilize the environment and climate of the trunk for electrical, mechanical, and chemical equipment that have been situated in the trunk. The fan has the added benefit of positive airflow through the trunk area, which helps to minimize contamination of dust and water in the trunk compartment when the lid is closed. The trunk fan is grounded to the vehicle body to support EMC compliance with electronic equipment. 16

17 COMPLETE POLICE PREP PACKAGE Permanent Rubber Tie-Down Strap Included with (68P), (65W) and (65U) This option provides a permanent rubber tie-down strap for securing the trunk lid when transporting large, irregular items. Note: When not in use, secure the tie-down strap to the inside of the trunk lid. Prior to vehicle operation, make sure that the tied down strap is secured. 17

18 COMPLETE POLICE PREP PACKAGE Dual Trunk Storage Boxes Included with (68P), (65W) and (65U) Caution: Be sure the jack is secured to the storage box to prevent damage to any items within the trunk. The two storage boxes are designed to house small equipment that should not be loose in the trunk. The boxes have clear polycarbonate covers for easy identification of their contents. The clear cover should be cleaned with non-abrasive cleaners. Caution: Be sure that both storage boxes are fully latched prior to vehicle operation. 18

19 COMPLETE POLICE PREP PACKAGE Rear Communications Service Tray Included with (68P), (65W) and (65U) The rear communications service tray is mounted on heavy-duty slides to provide easy access for equipment mounting, equipment servicing, and the spare tire. With the tray in its closed position it will help provide protection from any loose items and elements of the weather. Caution: Follow instructions for tire mounting to ensure proper retention of spare tire. This can prevent damage to the tray and the vehicle trunk interior. Caution: Be sure that both side latches are secured and in second locked position prior to vehicle operation. Improper latching may damage components and vehicle. OPENING THE LATCH 19

20 POLICE PREP PACKAGE Vehicle Speed Sensor and Battery Saver Circuits Vehicle Speed Signal and Battery Saver Circuits are available at the central console area for all police packages. Vehicle Speed Signal is a DC coupled square wave that varies in frequency in proportion to vehicle speed. The characteristics of the square wave are detailed below: Maximum High Signal (Vbat): Battery Voltage Minimum High Signal (Vbat): 3.67V Maximum Low Signal: 1.1V Minimum Low Signal: -1.0V Maximum Ground Offset: ±1.0V Rise time (tr): 10 m sec tr 250 m sec Fall time (tf): 10m sec tf 250 m sec Duty Cycle: 50% ± 10% Pulse Rate: 2.22Hz/MPH (1.3808Hz/KPH) Battery Saver Circuit is attached to the Lighting Control Module referring to interior lighting circuit. This circuit provides power for 30 min. after the engine has been shut down. The time is fix, can not be adjusted. The circuit is a low amperage circuit and can not be used to power directly any equipment. The battery Saver Circuit can be used just to activate relays for powering equipment. 20

21 VISIBILITY PACKAGE (65W), and READY FOR THE ROAD (65U) Strobe Power Unit This option provides a strobe power unit which is required to flash the four strobe bulbs in the vehicle as well as two capped cables located in the grill/radiator area. The supplied power supply has front shut down capability. There are control wires in the trunk for connection to a B+ switching device. Note: This option provides secondary lighting as defined by SAE Standards J1318 and J845. The four-corner strobe system is calibrated to maintain compliance to FMVSS-CMVSS 108, governing tail, stop, turn, and marker light intent and operation. The end user should select primary lighting as defined by SAE J1318 and J2495 to ensure proper identification of the emergency vehicle. ***See Page 39 Prior to Servicing*** 21

22 BASE LIGHTING PACKAGE (65P) Strobe Power Unit Base Lighting Package (65P) is the old Base Visibility Package (65N) restructured to give customers more flexibility to work with our package. The strobe power unit required to flash the four strobe lights in the car is mounted now on left side of the trunk on powder coated steel bracket along with the trunk Power Distribution Box. Note: This option provides secondary lighting as defined by SAE Standards J1318 and J845. The four-corner strobe system is calibrated to maintain compliance to FMVSS-CMVSS 108, governing tail, stop, turn, and marker light intent and operation. The end user should select primary lighting as defined by SAE J1318 and J2495 to ensure proper identification of the emergency vehicle. ***See Page 39 Prior to Servicing*** 22

23 VISIBILITY PACKAGE Flashing Rear Deck LED Lights Included with (65P), (65W) and (65U) This option supplies the user with two flashing high intensity LED lights mounted to the rear parcel shelf. These flashing lights come standard as one blue high intensity LED on the passenger side and one red high intensity LED on the driver side of the high-mount third brake light. Note: A Switch Control Panel is provided for (65W) and (65U) packages to control operation of the flashing rear deck LED lights. This switch panel triggers relays through a ground activation circuit which is not a power source to the LED lights. 23

24 REAR DECK LED LIGHTS Note: All connectors viewed from wire end. The new Rear LED Lights come to replace the existing first generation of LED Lights with the more bright third generation LED Lights. LED lights are preset with the same pattern (with no possibility to be changed). The red LED (driver side) is the control head and the blue one (passenger side) is the follower. When installing a new blue LED module, this has to be set as a follower unit. Having both units working as control units will cause the follower unit to not function properly. After connecting together red and blue units the control/ follower setting must be done. For setting the follower unit the push button at the back of the unit (inside the colored cover) has to be pushed for 5 sec. 24

25 VISIBILITY PACKAGE (65W) Switch Control Panel The functions of the 4-Position Slide Switch on the Switch Control Panel are defined as follows: Position 1: Position 2: Position 3: Position 4: FOUR Corner Strobes, Alternating High Beams plus Lighting Relay Center function 1* TWO Rear Corner Strobes, (front shut down) Flashing High Intensity LED plus Lighting Relay Center function 2* TWO Rear Corner Strobes, (front shut down) Flashing High Intensity LED plus Lighting Relay Center function 3* FOUR Corner Strobes, Alternating High Beams, Flashing High Intensity LED plus Lighting Relay Center function 4* The four red switches next to the slide switch are provided for control of light bar take-downs or other accessories not included in the Visibility Package, (customer installed). *For further light bar information, see page 46 25

26 SCHEMATICS This SCHEMATICS section serves to illustrate the location of the various fuses, wires, and relays. BL blue BK black BN brown DB dark blue DG dark green GN green GY gray LB light blue LG light green Note: KEY TO WIRE COLOR CODES NA natural OR orange PK pink PU purple RD red SR silver TN tan WH white YE yellow On dual color notation, the first color is for the wire and the second color is for the tracer (stripe). Format: Main wire color / Tracer (stripe) color. In-line fuse (10 AMP) located beneath glove box provided to protect ignition signal circuit. 26

27 SCHEMATICS Ford Engine Compartment Fuse Block Fuse Wire Color 111 TN/YE Function 1 Function 2 Load Radio (Blunt cut at console) Radio (Blunt cut in trunk) 50 Amp 112 PK Ignition Power Siren Amplifier (65U) 40 Amp 113 RD/YE Console Trunk Pigtail (65A & 68P) 114 RD/BL Trunk Pigtail (65A & 68P) 115 RD Trunk Pigtail (65A & 68P) Lighting Relay Center * (65P, 65W, & 65U) Lighting Relay Center * (65P, 65W, & 65U) Lighting Relay Center * (65P, 65W, & 65U) 50 Amp 50 Amp 50 Amp 116 TN Glove Box PDB 50 Amp 117 LG Blunt cut at Console 50 Amp 118 RD/WH Trunk PDB 50 Amp Inline PK In-line fuse located beneath glove box in separate holder 302 Police Power Relay * - See page 46 Provided to protect ignition signal circuit Used to switch ignition power on fuse Amp 27

28 SCHEMATICS Power Connection Placement Note: All connectors viewed from wire end. 28

29 SCHEMATICS Power Connection Placement Pin Gauge Color Function 1 10 RD/YE Fused Power (Fuse 1-113) 5 10 RD/WH Fused Power (Fuse 1-118) 6 10 RD Fused Power (Fuse 1-115) Pin Gauge Color Function 1 10 TN Fused Power (Fuse 1-116) 4 10 TN Fused Power (Fuse 1-116) 7 16 PK Ignition Signal (Fuse 10Amp Inline) TN Fused Power (Fuse 1-116) Pin Gauge Color Function 4 10 LG Fused Power (Fuse 1-117) 6 10 TN/YE Ignition Power (Fuse 1-111) 7 12 PK Fused Power (Fuse 1-112) 9 10 TN Fused Power (Fuse 1-116) RD/LB Fused Power (Fuse 1-114) Pin Gauge Color Function 1 10 RD/WH Fused Power (Fuse 1-118) 2 16 PK Ignition Signal (Fuse 10 Amp Inline) 9 10 RD/WH Fused Power (Fuse 1-118) RD/WH Fused Power (Fuse 1-118) Pin Gauge Color Function 1 10 PK Ignition Power 2 10 RD/LB Fused Power (Fuse 1-114) 3 16 RD/BK Siren Speaker (65U PKG) 4 16 BN Siren Speaker (65U PKG) Pin Gauge Color Function 1 10 RD/YE Secondary Power 4 10 RD Primary Power PK Ignition Signal 29

30 30 SCHEMATICS Power Circuit Placement (65A, 65P and 68P)

31 SCHEMATICS Power Circuit Placement (65A, 65P and 68P) 31

32 SCHEMATICS Power Circuit Placement (65W and 65U) Engine Compartment Interior 32

33 SCHEMATICS Power Circuit Placement (65W and 65U) Trunk 33

34 34 SCHEMATICS Spare Circuit Placement

35 SCHEMATICS Spare Circuit Placement 35

36 36 SCHEMATICS Ground Circuit Placement

37 SCHEMATICS Ground Circuit Placement 37

38 SCHEMATICS Strobe Power Supply Assembly (65P, 65W, 65U) 38

39 SCHEMATICS Strobe Power Supply Assembly WARNING: The strobe power supply is a high voltage device. Do not touch or remove the strobe lamp assembly while unit is in operation. Wait at least 10 minutes after shutting off power before continuing diagnostic. Failure to follow these instructions may result in personal injury. Correct Wiring Color Codes for Ford Product 2008 (8W7T-15A599) 2007 (7W7T-15A599) 2006 (6W7J-15A599) 2005 (5W7J-15A599) 2004 (4W7J-15A599) White Housing 1W7J-15C594-AA White Housing 1W7J-15C594-AA Strobe 2003 Phase 2 (3W7J-15A599) Strobe C B A C B A BK WH RD BK WH RD C B A C B A BK WH RD BK WH RD Female Amp Connector BK WH RD Male Amp Connector WH BK RD Visibility Pacakge Strobe Power Supply (Federal Signal Strobe Module Visibility Pacakge Strobe Power Supply (Federal Signal Strobe Module 2003 Phase 1 (1W7J-15A599) White Housing 1W7J-15C594-AA Note: All connectors viewed from wire end. Strobe C B A BK WH RD C B A WH BK RD WH BK RD Male Amp Connector Visibility Pacakge Strobe Power Supply (Federal Signal Strobe Module NOTE: Federal Signal modules other than the Ford supplied module, Federal Signal Silver Series and the Federal Signal Ricochet model should use the 2003 Phase 2 configuration and re-pin as shown. Other Industry standard configured modules should use the wiring pin-out. See module Manufacturer s instructions for exact color configurations. Correct color configurations are key to Strobe bulb longevity. 39

40 SCHEMATICS Console Pin outs (located under ashtray) (Available only in 65W and 65U Package) Vehicle Connector Terminal Gauge Color End Function Power Distribution Center, 1 16 DB/OR Headlight Flasher and Strobes Glove Box Power Distribution Center, Strobes and High Intensity LED 2 16 DG/PU Trunk Deck Lights 3 N/A Not Used Not Used 4 16 BK Ground Power Distribution 5 N/A Not Used Not Used 6 16 OR/YE Pin 7 Back Lighting 7 16 OR/YE Pin 6 Back Lighting 8 16 PK Vehicle Connector Under Instrument Panel at Glove Box Ignition Feed Auxiliary Plug Auxiliary Connector to 8-Relay Center in Trunk Terminal Gauge Color End Function 1 16 PU/LG Slide Switch 1 Light PU/LG Slide Switch 2 Light PU/YE Slide Switch 3 Light PU Slide Switch 4 Light OR/RD Toggle 1 Take Down 6 16 BK/OR Toggle 2 Auxiliary 7 16 WH Toggle 3 Left Alley 8 16 GY/BK Toggle4 Right Alley Caution: Do not reverse connectors when installing in switch box. Note: These connectors are for use only in the visibility packages 65W and 65U. Note: All connectors viewed from wire end. 40

41 SCHEMATICS Alternating Headlight Flasher Circuit 41

42 42 SCHEMATICS Horn / Siren Relay Circuit (Amplifier at Console)

43 SCHEMATICS Horn / Siren Relay Circuit (Amplifier in Trunk) 43

44 SCHEMATICS Glove box Power Distribution Center R2.A6 R2.A5 R2.A4 R2.A3 R2.A2 R2.A1 44

45 SCHEMATICS Trunk Power Distribution Center R4.B5 R4.B4 R4.B2 R4.B1 45

46 SCHEMATICS 8-Relay Panel (65W) R4.C8 R4.C7 R4.C6 R4.C5 R4.C4 R4.C3 R4.C2 R4.C1 46

47 REMOVAL OF POLICE PREP PACKAGES Note: When retiring a police vehicle, it is the owner s responsibility to remove any police-related apparatus that is not intended for civilian use. The Police Prep Packages contain a vehicle harness which does not need to be removed, only disabled by removing fuses 111, 112, 113, 114, 115, 116, 117, and 118 in the engine compartment. All strobe bulbs need to be disconnected from the strobe power supply. The Visibility Package contains two rear parcel shelf mounted LED lights and a rear communications service tray mounted strobe power unit which should be removed. 47

48 GENERAL GUIDELINES General Guidelines Circuit protection (fuses) must be provided for all wiring. The fuse rating should not exceed either the rated wiring current capacity or the total current requirements for all the add-on components on the circuit. Fuses should be installed as close to the point of tapped power as possible. All revisions to the electrical system should be documented and placed with the vehicle owner guide. All revisions or additions to wiring should be color coded and/ or labeled. Protective covering should be provided in all areas that could be damaged during normal equipment installations. Vehicles stored on site should have the negative battery cable disconnected to reduce the possibility of draining the battery by lights or other equipment. Control panels attached to the instrument panel should not protrude into the driver and passenger air bag deployment zones. For additional information, refer to Section 4: Installation Considerations in this guide. Switches and gauges should not be installed in the driver or passenger knee impact areas. All Ford gauges, lights, and switches must be inspected for correct operation after instrument panel work is performed. All wiring relocated or removed while working behind the instrument panel must be secured properly to prevent chafing, squeaks and rattles. Provide adequate retention for wiring harnesses so that they are clear of bolts, corners, edges, etc., which could abrade the wires during normal vehicle operation. Anticipate misrouted wiring situations and protect all wiring from penetration by screws and raw edges. Weather-seal all electrical connectors exposed to the elements. Do not use quick splice connectors or wire nuts. Connections should be easily accessible for assembly and service. Make sure submersible connectors do not lose their seals u n d e r e xt r em e as s e m b l y conditions, such as bending wires 90 degrees immediately after the connector. Whenever using connectors, use a socket (female) connector on the electrical source side and a plug (male) connector on the electrical load side to reduce the 48

49 GENERAL GUIDELINES possibility of a short circuit when disconnected. Air bag restraint systems must remain intact as received from Ford Motor Company. Before modifications are done to the vehicle, the system must be disarmed by following the instructions provided in the current Crown Victoria Workshop Manual. Adherence to the above guidelines is not to be construed as approval by Ford Motor Company of any specific revisions or additions to the vehicle s original electrical system. Wire Insulation Polyvinyl Chloride (PVC) rated at 90 C (199 F) is the standard wire insulation that is acceptable for inside body use but is not acceptable for underhood/ underbody wiring. Hypalon insulation should be used on links only (Ford Specification ESB-M1L54-A). Cross-linked Polyethylene (PLPE or SL) rated at 135 C (275 F) is the required insulation f o r u n d e r h o o d / u n d e r b o d y applications (Ford Specification ESB-M1L123-A). GL can be used as an alternate wire (Ford Specification ESB-M7L85B) as long as the concentricity specifications are met. To provide a water-resistant seal in conjunction with crimp connectors, a Duraseal crimp connector is recommended since it is designed to account for outside wire diameter that is smaller than the present SL wire. Splices and Repairs For quality splicing and to reduce potential problems, the following guidelines are recommended: Stagger the splices within a harness to reduce increased harness diameter. Splice only on straight areas as installed, not on bends. Strip wire ends making sure that individual conductor strands are not damaged. When soldering, make sure an adequate mechanical joint exists before applying solder. Use only resin-core solder. Acid-core solder should not be used since it may result in corrosion. For crimp joints, use butt-type metal barrel fasteners and the proper tool at the appropriate setting for the wire size (such as Motorcraft crimp tool S-9796) specifically designed for this type of work. 49

50 GENERAL GUIDELINES Make sure splice joints are adequately sealed and insulated. In an outside environment, use Duraseal butt connectors or equivalent. A durable substitute splice joint can be achieved by using a bare metal barrel, crimping, flow-soldering and covering with shrink tubing (see figure). Quality electrical tape can be used inside the vehicle but is not recommended for an outside environment. Be sure that the new wire is not a lesser gauge than its original mating wire. Recommended splicing method 1. Disconnect the battery 2. Strip wires to appropriate length. 3. Install heat shrink tubing. 4. Twist wires together. Note: Use resin-core mildlyactivated (RMA) solder. Do not use acid-core solder. 50

51 GENERAL GUIDELINES 5. Solder wires together. Note: Wait for solder to cool before moving wires. 6. Bend Wire 1 back in a straight line. Note: Overlap tubing on both wires. 7. Evenly position heat shrink tubing over wire repair. 8. Use heat gun to heat the repaired area until adhesive flows out of both ends of heat shrink tubing. Ford Part Number Part Name Class E6FZ A E6FZ B E6FZ C BUTT CONNECTOR GAUGE: 18-22, COLOR:RED BUTT CONNECTOR GAUGE: 14-16, COLOR:BLUE BUTT CONNECTOR GAUGE: 10-12, COLOR:YELLOW C C C 51

52 GENERAL GUIDELINES Heat Shrinkable Tubing (Heat Shrink) (Ford Specification ESB- M99D56-A2) Heat shrinkable tubing is available in various diameters for different splice sizes and configurations. When shrunk, it forms a small, flexible hermetic seal. Other methods (tape, PVC mold, etc.) do not provide a hermetic seal and are not recommended. Splice balancing is critical with heat shrink insulation. If the splice is extremely unbalanced (more circuits on one side than the other), heat shrink insulation will not provide a proper seal. Evaluate the use of double terminals instead of splices where practical in these situations. Wire Protection Requirements General Notes: Anticipate problems and design accordingly. Try to anticipate what could go wrong and modify your designs to address any adverse impact. R e v i e w a l l c o n n e c t o r applications and electrical systems to determine the need for solder, grease, weather-resistant or sealed connectors. Make sure components and wire insulation are c om p at i b l e with g r eased connectors (important for long term durability). Make sure that drip loops or other means are provided to prevent water leakage into the vehicle through wiring assemblies that pass through the dash panel. Use greased or sealed connectors in floor pan troughs which are subject to moisture coming through the carpeting. Use LPE insulation for uncovered runs that exceed 305 mm (12 inches). Electrical Protection Properly route wires away from noise-generating wires or components. However, if routing near noisy wires or plugging into noisy components is unavoidable, additional protection must be designed into the harness. Shielding Electro Magnetic Interference (EMI) Consider shielding if you must route close to high-current or noisy circuits. Use shielded wire and ground one side. Seal all splices in wire assemblies that use bare coaxial shielding (braid or tape) for EMI suppression, and insulate or tape over all shielding ends that terminate near any open connectors. This prevents splice and terminal shorts to the shielding. Minimize the length of 52

53 GENERAL GUIDELINES conductors which extend beyond the shield. Failure to do this reduces the effectiveness of the shield. Spike suppression, in general, is accomplished by connecting a d i o d e o r r e s i s t o r - d i o d e combination across the terminals of the noisy component. The diode should be sufficiently close to the component (both electrically and physically) so that inductive spikes are clamped off. Make sure the diode is connected with the proper polarity. Proper routing and retention will reduce the likelihood of chafing, pinching, etc. When this ideal routing is unattainable, the following additional protection is needed: M echanical/en vironment al Protection Tape Tape is the most basic means of protection. It contains the wires in a loose bundle and provides limited environmental protection. It does not protect against chafing and pinching. Kendall Polyken Fiberglass Base Tape (Ford Specification ESB-M3G38-A) is used for engine compartment applications. This durable tape provides against cutthrough and abrasion commonly found in underhood applications. Polyken 267 is a substitute tape that may be used in lower temperature areas of the engine compartment (apron area). Convolute - Use convolute for all underhood/underbody applications or when increased temperature, abrasion or pinch resistance is required. Convoluted tubing comes in different diameters and materials to accommodate different temperature ranges and harness sizes. Use polyethylene convolute when abrasion is the only consideration; this convolute is adequate up to 96 C (205 F) maximum. Use nylon convolute when underhood/underbody or abrasion and temperature are considerations; nylon convolute is adequate up to 177 C (350 F) maximum. On all engine-mounted wiring or bend points. Use vinyl tape on the outside of the convolute to prevent wiring from looping out. This tape must be able to withstand temperatures over 135 C (275 F). 53

54 Ford Motor Company warrants the Police Interceptor Preparation Packages under the Ford New Vehicle Warranty. All Ford Product Warranty Service is provided through the Ford Dealer Organization. Please contact your dealer for warranty service assistance. While certain components may be sourced through recognized vendors, those vendors are not Ford Product Warranty Service Centers. Crown North America Technical Assistance, Customer Service and Sales 1 (866) Assistance with Ford equipment not installed by Crown Ford Fleet Technical Assistance 1 (800) 34-FLEET

55