556U Immobilizer Interface
|
|
- Loraine McLaughlin
- 6 years ago
- Views:
Transcription
1 556U Immobilizer Interface Product Description The 556U immobilizer interface module is used when installing remote start products in vehicles equipped with an RF (Radio Frequency) based immobilizer system. This type of system uses a small chip imbedded in the ignition key, called a transponder, to transmit a very low powered RF signal. This signal is picked up through an antenna (or coil) around the ignition switch which is then sent to the immobilizer s transceiver. Once the correct signal is received, the immobilizer will enable the ignition and/or fuel systems. If an attempt is made to start the vehicle and the transceiver does not receive a valid code, the ignition and sometimes the fuel systems are disabled. The immobilizer system will then render the remote start useless. The 556U bypasses the immobilizer system only while the remote start is in use, maintaining the factory system s integrity. When the remote start system is not in use the factory immobilizer remains fully functional. 6-Pin Harness RED (+) 12 Volt Input: Connect this wire to a fused source of constant 12V. BLUE (-) Status Input: Connect this wire to the remote start negative (-) status output. PINK (+) Ignition Input: Connect this wire to the vehicle s true ignition output. (Refer to Latching Input, page 7.) BLACK (-) Chassis Ground Input: Connect this wire to the vehicle s chassis ground. VIOLET (+) Keysense Input: Connect this wire to the vehicle s positive keysense output wire. (Refer to Key Sense Inputs, page 7.) GREEN (-) Keysense Input: Connect this wire to the vehicle s negative keysense output wire. (Refer to Key Sense Inputs, page 7.) 3-Pin Harness BLACK and BLACK/RED Wires: Both of these are antenna ring wires. BLACK/WHITE: Refer to alternate wiring diagram. 1
2 Immobilizer Interface Instructions Please note that the instructions outlined in the Standard Immobilizer Interface section describe an immobilizer interface that will work with the majority of vehicles; however, some vehicle immobilizer systems may require an alternate interface due to mounting issues, cosmetic differences, or RF loss when coupling the factory key RF with the 556U to the factory transponder ring. (See Alternate Immobilizer Interface.) IMPORTANT! Before beginning the installation inform the customer that one of the vehicle s coded keys must be used in the installation and installed permanently in the unit. If a new key is being purchased through the dealer, make sure to code the new key to the factory immobilizer or have the dealer do this. In many vehicles, the new key must be coded at the dealer. IMPORTANT! It is also the installer's responsibility to notify customers of the following: If they wish to have additional keys programmed to the vehicle's immobilizer system in the future, certain vehicle manufacturers require that all programmed keys be reprogrammed at the time that the keys being added to the system are programmed. In this case, it would be necessary to remove the already programmed key from the 556U module to reprogram it. (If the customer plans on having additional keys programmed to the vehicle in the future, the shaft of the key should not be altered.) 2
3 Standard Immobilizer Interface 1. Open the control module and place the vehicle s coded key through the center of the black receiver ring as shown. 2. Reassemble the control module. This will secure the key inside. IMPORTANT! When using the ring method of installing the 556U, the ring from the 556U MUST be in front of the factory receiver ring. It CAN NOT be on top of, or behind the factory receiver ring. See illustration below. 3. Disassemble the steering column shroud and place the antenna ring around the vehicle s ignition switch as shown, and plug into the control module. 4. Plug the 6-pin power plug into the control module. 5. Connect the BLACK wire to chassis (ground). 6. Connect the red wire to a fused source of constant 12V. 7. Connect the blue wire to the status output (blue wire) of the remote start system that provides a latched negative (-) ground while the remote start is active. 8. Test unit before reassembling the steering column. 9. Reassemble the steering column shroud. 3
4 INCORRECT CORRECT 2000 Directed Electronics, Inc. 4 N556U 5/00
5 Alternate Immobilizer Interface No. 1 This type of interface will only work with immobilizer systems that have a two-wire factory antenna harness. This alternate interface method is not guaranteed to work with all immobilizer systems, due to differences in transponder systems. It is meant to provide the installer with an alternative interface method for most two-wire transponder ring systems. This method will not work on European vehicles. 1. Open the control module and place the vehicle s coded key through the center of the black receiver ring as shown. 2. Reassemble the control module to secure the key inside. 3. Disassemble the steering column shroud and locate the factory transponder ring s antenna wires. The two wires are usually located in a tube routing from the transponder ring to the factory transceiver module. NOTE: Some vehicles may require other methods to access the factory transponder ring antenna wires. 5
6 4. Plug the three-pin connector into the 556U module and cut the 556U s antenna wire off. Discard the antenna ring. 5. Split open the factory transponder ring tube and cut one of the two wires in half. 6. Connect the factory transponder ring side of the cut wire to the BLACK/WHITE normally closed input wire of the 556U. 7. Connect the factory transceiver module side of the cut wire to the 556U s BLACK wire. 8. Connect the BLACK/RED wire to the uncut factory transponder ring antenna wire. 9. Plug the 6-pin power plug into the control module. 10 Connect the BLACK wire to chassis ground. 11. Connect the RED wire to a fused source of constant 12V. 12. Connect the BLUE wire to the status output (blue wire) of the remote start system that provides a latched negative (-) ground while the remote start is active. 13. Test unit before reassembling the steering column. 14. Reassemble the steering column shroud. 6
7 Alternate Immobilizer Interface No. 2 This type of interface will only work with immobilizer systems that have a two-wire factory antenna harness. This alternate interface method is not guaranteed to work with all immobilizer systems, due to differences in transponder systems. It is meant to provide the installer with an alternative interface method for most two-wire transponder ring systems. This method will work on European vehicles. 1. Open the control module and place the vehicle s coded key through the center of the black receiver ring as shown. 2. Reassemble the control module to secure the key inside. 3. Disassemble the steering column shroud and locate the factory transponder ring s antenna wires. The two wires are usually located in a tube routing from the transponder ring to the factory transceiver module. NOTE: Some vehicles may require other methods to access the factory transponder ring antenna wires. 7
8 4. Plug the three-pin connector into the 556U module and cut the 556U s antenna wire off. Discard the antenna ring. 5. Split open the factory transponder ring tube and cut one of the two wires in half. 6. Connect the factory transponder ring side of the cut wire to the BLACK/WHITE normally closed input wire of the 556U. 7. Connect the factory transceiver module side of the cut wire to the 556U s BLACK wire. 8. Connect the BLACK/RED and BLACK/WHITE wires to the factory transponder ring side of the cut wire. 9. Plug the 6-pin power plug into the control module. 10 Connect the BLACK wire to chassis ground. 11. Connect the RED wire to a fused source of constant 12V. 12. Connect the BLUE wire to the status output (blue wire) of the remote start system that provides a latched negative (-) ground while the remote start is active. 13. Test unit before reassembling the steering column. 14. Reassemble the steering column shroud. Vehicle Applications The 556U works with most RF based immobilizer systems. Refer to DirectWire for specific applications. Jumper Settings The 556U is shipped with the jumper set in a 60 winding position (mode 2). For most applications this should be the optimal setting. Moving the jumper will set the 556U to work off of a 18 winding position (mode 1). You may use the 18 winding for American and Asian vehicles, but for European vehicles the 60 winding setting is required. Mode 2 jumper position will be more sensitive to picking up the key vice mode 1 jumper position. Key Sense Inputs Some vehicles require the vehicle never read two keys at the same time (Ford Escape, Mazda Tribute). These vehicles require the key sense wire to be located in the vehicle. This wire will show either ground (-) or positive (+) voltage when the key is slid in the ignition and the key chime sounds. Depending on the polarity of the vehicle attach either the GREEN (-) or the VIOLET (+) wire from the 556U to the key sense wire in the vehicle. When the 556U senses an input on these wires it will drop out immediately allowing the vehicle to only see the key that was just placed in the ignition cylinder. Latching Input Some vehicles require that the key code does not change during a run cycle (Mercedes ML series). By attaching the PINK wire from the 556U to the ignition wire in the vehicle, the 556U will stay engaged the entire time the vehicle is running. This includes after the take-over with the key. With the PINK wire of the 556U attached to the ignition in the vehicle, the 556U will stay engaged until the vehicle is shut off. 8
556L General Motors Passlock Interface Module
556L General Motors Passlock Interface Module Product Description The 556L General Motors Passlock Interface Module is used when installing remote start products in GM vehicles equipped with Passlock I
More informationVEHICLE THEFT/SECURITY SYSTEMS
TJ VEHICLE THEFT/SECURITY SYSTEMS 8Q - 1 VEHICLE THEFT/SECURITY SYSTEMS CONTENTS page GENERAL INFORMATION INTRODUCTION... 1... 1 DESCRIPTION AND OPERATION SENTRY KEY IMMOBILIZER MODULE... 1 INDICATOR LAMP...
More informationVEHICLE THEFT/SECURITY SYSTEMS
TJ VEHICLE THEFT/SECURITY SYSTEMS 8Q - 1 VEHICLE THEFT/SECURITY SYSTEMS CONTENTS page GENERAL INFORMATION INTRODUCTION... 1... 1 DESCRIPTION AND OPERATION SMART KEY IMMOBILIZER MODULE... 1 INDICATOR LAMP...
More informationVEHICLE THEFT/SECURITY SYSTEMS
WJ VEHICLE THEFT/SECURITY SYSTEMS 8Q - 1 VEHICLE THEFT/SECURITY SYSTEMS CONTENTS... 6 VEHICLE THEFT SECURITY SYSTEM... 1 VEHICLE THEFT SECURITY SYSTEM INDEX AND DOOR AJAR SWITCH... 3 DRIVER CYLINDER LOCK
More informationVEHICLE THEFT/SECURITY SYSTEMS
XJ VEHICLE THEFT/SECURITY SYSTEMS 8Q - 1 VEHICLE THEFT/SECURITY SYSTEMS TABLE OF CONTENTS page DESCRIPTION AND OPERATION...1 SENTRY KEY IMMOBILIZER MODULE....1 SENTRY KEY IMMOBILIZER TRANSPONDER...2 INDICATOR
More informationVEHICLE THEFT/SECURITY SYSTEMS
XJ VEHICLE THEFT/SECURITY SYSTEMS 8Q - 1 VEHICLE THEFT/SECURITY SYSTEMS TABLE OF CONTENTS page GENERAL INFORMATION INTRODUCTION...1...1 DESCRIPTION AND OPERATION SENTRY KEY IMMOBILIZER MODULE....1 SENTRY
More information2002 Dodge Intrepid ES ACCESSORIES & EQUIPMENT Anti-Theft Systems - Concorde, Intrepid & 300M
DESCRIPTION SENTRY KEY IMMOBILIZER SYSTEM 2002-03 ACCESSORIES & EQUIPMENT Anti-Theft Systems - Concorde, Intrepid & 300M CAUTION: Large metallic objects, or items such as magnetic pass-keys, may cause
More informationFM SECURITY AND REMOTE START SYSTEM
FM SECURITY AND REMOTE START SYSTEM INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! This system is intended for installation on vehicles equipped with
More informationAftermarket Interface Module
An ISO 9001:2008 Registered Company Aftermarket Interface Module (2015-2018 Ford Transit) AIM514-B High Side Solenoid type Coolant Valve Control AIM515-B Motor Reversing type Coolant Valve Control Introduction
More information1999 Mercury Cougar ACCESSORIES & EQUIPMENT' 'Passive Anti-Theft Systems - Cougar 1999 ACCESSORIES & EQUIPMENT
DESCRIPTION 1999 ACCESSORIES & EQUIPMENT Passive Anti-Theft Systems - Cougar Passive Anti-Theft System (PATS) is available on some vehicles. The system is passive in that it does not require any activity
More informationDLKEK3HN INSTALLATION INSTRUCTIONS
DLKEK3HN INDEX: INSTALLATION INSTRUCTIONS WIRING INSTRUCTIONS... PG 2-5 LED STATUS INDICATOR... PG 6 VALET/OVERRIDE BUTTON... PG 6 SHOCK SENSOR... PG 7 PROGRAMMABLE JUMPER-PINS... PG 7 PROGRAMMING REMOTE
More informationPart Number:
General Applicability This cruise control was tested and verified on: 2009-2010 Ford F-150 / E-150 2010 Ford Escape 2009-2010 Mazda Tribute This cruise control may not function correctly on unverified
More informationCS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM
INTRODUCTION: CS-865RKE Series II REMOTE KEYLESS ENTRY SYSTEM INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a Remote Keyless Entry System by Crimestopper Security Products Inc.
More informationFS-30 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION INSTRUCTIONS
FS- 2-WAY REMOTE CONTROL ALARM SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of an Remote Alarm System by Crimestopper Security Products Inc. This booklet contains the information
More informationModel PRO 9246CH Installation Manual
Model PRO 9246CH Installation Manual PRE-INSTALLATION NOTES: RF Programmable Features : Feature Selection 1 Flash 2 Flash 3 Flash Default 1st Do L/UL 1 Sec. 3.5 Sec. 1 Sec L, Dbl. U/L 1 Sec. 2nd Accy Lock
More informationRF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY)
RF-425LCD PROFESSIONAL VEHICLE SECURITY SYSTEM INSTALLATION MANUAL (FOR AUTHORIZED DEALERS ONLY) THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY 1 BLUE...TRUNK/HOOD TRIGGER (-) INPUT BLACK/BLUE...4TH
More information2001 Dodge Durango ACCESSORIES & EQUIPMENT' 'Anti-Theft Systems - Dakota & Durango 2001 ACCESSORIES & EQUIPMENT
DESCRIPTION VEHICLE THEFT SECURITY SYSTEM 2001 ACCESSORIES & EQUIPMENT Anti-Theft Systems - Dakota & Durango Vehicle Theft Security System (VTSS) provides perimeter protection against unauthorized use
More informationCSI-400 Installation Instructions
CSI-400 Installation Instructions Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components or routing wires near hot surfaces
More informationREC-11+ REMOTE RECEIVER UNIT
Resetting The Programmable Features The installer may quickly and easily return all 17 programmable features back to the factory settings. Changing individual features were explained in detail in the previous
More informationCA 421 Installation Instructions
CA 421 Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting components
More informationADD-ON REMOTE STARTER TO AFTERMARKET SYSTEM
MEGATRONIX RS 110 ADD-ON REMOTE STARTER TO AFTERMARKET SYSTEM Installation and Operation Manual MEGATRONIX CHATSWORTH, CA U.S.A. RS110 ADD-ON REMOTE CAR STARTER For Vehicles Equipped With Automatic Transmission
More informationModel RK1 installation guide
Model RK1 installation guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result
More informationINTERFACE PART NUMBER NOTES
2002 Infiniti I35 ALARM REMOTE START WIRING WIRE COLOR LOCATION 12V CONSTANT WIRE GREEN Ignition Harness 12V IGNITION WIRE BLACK/RED (smaller) Ignition Harness STARTER WIRE BLACK/RED or Ignition Harness
More informationINTERFACE PART NUMBER NOTES
2000 Saturn S-Series ALARM REMOTE START WIRING WIRE COLOR LOCATION 12V CONSTANT RED Ignition Harness STARTER YELLOW Ignition Harness IGNITION PINK Ignition Harness ACCESSORY ORANGE Ignition Harness SECOND
More informationRS900/RS901 SERIES IV RS999 FM FLASHBACK REMOTE ENGINE STARTING SYSTEM INSTALLATION INSTRUCTIONS
RS900/RS901 SERIES IV RS999 FM FLASHBACK REMOTE ENGINE STARTING SYSTEM INSTALLATION INSTRUCTIONS PRE-INSTALLATION CONSIDERATIONS To ease installation, we suggest that you READ THIS MANUAL and consider
More information2005 Directed Electronics Vista, CA N561T 07-05
Model 561T Installation Guide 2005 Directed Electronics Vista, CA N561T 07-05 table of contents what is included........................ 3 warning! safety first..................... 4 installation points
More informationCA-510a Installation Instructions
CA-510a Installation Instructions PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Kit Contents Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationDLRM DLRM
Table of Contents 1. Before You Begin.........................................................Page 1 2. Installation Tips..........................................................Page 2 3. Mounting Components
More informationINSTALLATION MANUAL. Model: PLUS For Technical Assistance, please call (800) , or visit
R Vehicle Security INSTALLATION MANUAL Model: PLUS-4700 This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference;
More informationFEB/20/2003 COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A 1
COMMANDO EZ-2500 REMOTE ENGINE STARTER WITH KEYLESS ENTRY SYSTEM INSTALLATION MANUAL 550A 1 INTRODUCTION FEB/20/2003 INSTALLER WARNINGS This Remote Starter with Alarm System is designed to be installed
More information2 WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE
REV. ARS. WAY REMOTE STARTER & ALARM SYSTEM INSTALLATION GUIDE FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This device may not cause
More informationFEB.20, 2003 COMMANDO MODEL FM-870 REMOTE ENGINE STARTER WITH ALARM SYSTEM INSTALLATION MANUAL RST872 1
COMMANDO MODEL FM-0 REMOTE ENGINE STARTER WITH ALARM SYSTEM INSTALLATION MANUAL RST2 1 HJKL TABLE OF CONTENTS: INSTALLATION DIAGRAM..... 4 H1: 6 PIN HEAVY GAUGE WIRING CONNECTION.... 6 H1/1 Violet Wire
More informationCS-2011RS. Super Rage. Remote Control Alarm System & Remote Engine Starting System INSTALLATION INSTRUCTIONS INSTALLATION CAUTIONS & WARNINGS
CS-2011RS Super Rage Remote Control Alarm System & Remote Engine Starting System INSTALLATION INSTRUCTIONS INSTALLATION CAUTIONS & WARNINGS To ease and reduce installation time, we suggest you consider
More informationRemote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start
Remote Starter Integration for the 2007 Toyota Camry equipped with the Smart Key System with Push Button Start 1.0 Material required: - Remote Car Starter - Xpresskit : XK05-PKT2 or Bypasskit :PKT2 - One
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationRemote Start with Keyless Entry Installation Guide CA 5051
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide CA 5051 2010 Audiovox Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin... 3 Wire Connection Guide...
More information2011 Model Year BBCV Vision and Model Year D3 All American CORRECTIVE ACTION ---- PROCEDURE
Cruise Control May Not Deactivate 2011 Model Year BBCV Vision and 2010-2011 Model Year D3 All American ISSUE Once activated the cruise control feature may not deactivate as designed when the service brakes
More informationINSTALLATION GUIDE Table of Contents
CT-3100 Automatic transmission remote engine starter systems. What s included..2 INSTALLATION GUIDE Table of Contents Door lock toggle mode..... 4 Notice...2 Installation points to remember. 2 Features..2
More informationMatrix RSIII Installation Guide
Matrix RSIII Installation Guide 2003 Directed Electronics, Inc. Vista, CA N909554 2-03 The Bitwriter (p/n 998T) requires chip version 1.4 or newer to program this unit. www.directechs.com DirectFax 800-999-1329
More informationCS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION
CS-2001 REMOTE CONTROL ALARM SYSTEM INSTALLATION & OPERATING INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Gargoyle Remote Alarm System by Crimestopper Security Products Inc. This booklet
More informationAutomatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst
PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide for models: ca5153 ca5153sst 2012 Audiovox Electronics Corporation. All rights reserved. 1 Table of
More informationALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATION PRECAUTIONS & WARNINGS
CS-882 OEM ALARM UPGRADE FOR FACTORY REMOTE KEYLESS ENTRY SYSTEM INSTALLATI PRECAUTIS & WARNINGS NOTE: This system does not improve or affect the range of the factory remote keyless entry transmitters.
More informationINSTALLATION MANUAL. Model: PLUS Vehicle Security
R Vehicle Security INSTALLATION MANUAL Model: PLUS-5000 Copyright 1999 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be a Registered
More informationCovers All 35xx Series Advanced 2-Way Remote Starters. Technical Support: ext 0
INSTALL GUIDE Covers All 35xx Series Advanced 2-Way Remote Starters www.ultrastarters.com Technical Support: 866-698-5872 ext 0 support@ultrastarters.com Warning!! The system must be placed into Service
More informationINSTALLATION MANUAL. Remote Mobile Security System. Model: PL30
Remote Mobile Security System INSTALLATION MANUAL Model: PL30 Copyright 1998 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be
More informationSERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL
SERIES 700/700E FACTORY KEYLESS UPGRADE INSTALLATION MANUAL Items Supplied with the System: Installation Instructions: Main unit 1. Mounting the module: Plug In LED Mount the module in a suitable location
More informationAutomatic / Manual Transmission Remote Start with Keyless Entry Installation Guide. ca 5152
PROFESSIONAL SERIES Automatic / Manual Transmission Remote Start with Keyless Entry Installation Guide ca 5152 1 Table of Contents Before You Begin... 3 Wire Connection Guide... 4 11 Pin Main Harness...
More informationAUTOMATIC TRANSMISSION ONLY! Technical Support: ext 1 Warning!!
REV.2006.04 INSTALL GUIDE AUTOMATIC TRANSMISSION ONLY! www.ultrastarters.com Technical Support: 877-598-2100 ext 1 support@ultrastarters.com Warning!! The system must be placed into Service Mode before
More informationShaved-B. Installation Manual & Operation Instructions
Shaved-B Installation Manual & Operation Instructions Each Kit Contains The Following Components (1) Receiver (2) Remotes (2) Wire Harnesses Installation Instructions for SPAL Shaved Door Handle Kit Shaved-40
More informationVEHICLE SECURITY SYSTEM INSTALLATION MANUAL
VEHICLE SECURITY SYSTEM WITH REMOTE START & NETWORK INTERFACE INSTALLATION MANUAL BEFORE INSTALLING THIS PRODUCT PLEASE READ THIS INSTALLATION MANUAL THOROUGHLY!! Before You Begin This system is intended
More information2005 Directed Electronics, Vista, CA N562T 07-05
Model 562T Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result
More informationModel 5500 Installation Guide
Model 5500 Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result
More informationFS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS
FS-22 and FS-32 KEYLESS ENTRY and ALARM SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION CONGRATULATIONS on your choice of a Remote Keyless Entry and Alarm System by Crimestopper Security Products Inc. This
More informationFOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES
#STARTC2003-TW TWO-WAY FM/FM REMOTE CONTROL VEHICLE STARTER & ALARM SYSTEM INSTALLATION GUIDE FOR AUTOMATIC TRANSMISSION AND DIESEL ENGINE VEHICLES THIS UNIT MUST BE INSTALLED BY AN AUTHORIZED MICRO ALARM
More informationMEGA WAY LCD REMOTE ENGINE STARTER AND CAR ALARM SECURITY. Installation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 2700 INSTALL 1
MEGA 2700 2-WAY LCD REMOTE ENGINE STARTER AND CAR ALARM SECURITY Installation Manual MEGATRONIX CALIFORNIA, U.S.A. MEGA 2700 INSTALL 1 2 1. Blue: (-) Unlock Pulse. Or (+)Lock Pulse. 3. Green: (-) Lock
More information*DISCONNECT BATTERY BEFORE INSTALLATION*
*DISCONNECT BATTERY BEFORE INSTALLATION* It is best to avoid starting a vehicle for the first time with the Terminator. Instead get the vehicle running well with a standard ignition switch or other simple
More informationModel 551R Installation Guide
Model 551R Installation Guide 2000 Directed Electronics, Inc. Vista, CA N551R 12-00 table of contents What Is Included..................... 3 Warning! Safety First.................. 4 Installation Points
More informationMaxx 3 Installation Guide
Maxx 3 Installation Guide 2002 Directed Electronics, Inc. Vista, CA N840003 4-02 Table of Contents Important Information....................................................... 3 System Components........................................................
More informationStep 1 Wiring your remote start. Installation Tips for your Remote Start system (for GM vehicles) V3.3 revised 9/12/2013
Installation Tips for your Remote Start system (for GM vehicles) V3.3 revised 9/12/2013 Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts to
More informationElectronic Vehicle Immobilization System EWS 2
Page 1 of 6 Electronic Vehicle Immobilization System EWS 2 History of BMW vehicle immobilization systems On vehicles produced up to late 1994 vehicle immobilization can be activated via the antitheft alarm
More informationTIP SHEET. Installation Tips for your RS IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14. 1 P a g e
Installation Tips for your RS-150 + IB-MUX / PKUMUX (D) + SPDT T1205 v1.2 4/3/14 TIP SHEET Thank you for purchasing your remote start from MyPushcart.com - an industry leader in providing remote starts
More informationREMOTE ENGINE STARTING SYSTEM INSTALLATION INSTRUCTIONS
RS900/RS901 SERIES V RS999 FM FLASHBACK NEW FEATURES! Timed Crank mode, Diesel Delay time, & Pos. or Neg. glow plug input. REMOTE ENGINE STARTING SYSTEM INSTALLATION INSTRUCTIONS INTRODUCTION Congratulations
More information2006+ Toyota Yaris Remote Start Wiring Guide
2006+ Toyota Yaris Remote Start Wiring Guide Note: This guide assumes that the user has a good working knowledge of automotive electrical systems. The user assumes all liability for any damage resulting
More informationChevrolet Camaro 2010-up S-LC
INSTALLATION INSTRUCTIONS FOR PART 99-10S-LC APPLICATIONS Chevrolet Camaro 2010-up 99-10S-LC KIT FEATURES DIN and DDIN head unit provision Painted silver to match factory dash AXXESS Interface included
More informationC3-RS-915 INSTALLATION MANUAL
C3-RS-915 PROFESSIONAL 2-WAY 915 MHz. LCD REMOTE CAR STARTER & 6 CHANNEL ALARM SYSTEM With Built-in Voltage & Temperature Sensor And Two Way Serial Port Data Link INSTALLATION MANUAL Compatible THIS PRODUCT
More informationModel Installation Guide
Model 4400 Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result
More informationCS-2011RS Series III / CS-2015FM Super Rage The Informer
CS-2011RS Series III / CS-2015FM Super Rage The Informer INSTALLATION INSTRUCTIONS INTRODUCTION Congratulations on your choice of a Crimestopper combo alarm & remote engine starter! This installation Handbook
More informationINSTALLATION MANUAL. Remote Mobile Security System. Model: PL50
Remote Mobile Security System INSTALLATION MANUAL Model: PL50 Copyright 2000 Magnadyne Corporation For Technical Assistance (800) 638-3600 For Fax on Demand Technical Assistance (800) 994-9977 (Must be
More informationRemote Start with Keyless Entry Installation Guide ca5054
PROFESSIONAL SERIES Remote Start with Keyless Entry Installation Guide ca5054 2014 Voxx Electronics Corporation. All rights reserved. 1 Table of Contents Before You Begin...3 Wire Connection Guide...4
More information2005 Directed Electronics, Vista, CA N
Model 4100 Installation Guide 2005 Directed Electronics, Vista, CA N831002 07-05 table of contents what is included........................ 3 warning! safety first..................... 4 installation points
More informationREAD ME FIRST TECHNICAL SUPPORT FORD-KEY CANADIAN DEALERS BILINGUAL FRENCH/ENGLISH TECHNICAL SUPPORT (514)
READ ME FIRST TECHNICAL SUPPORT 1-800-FORD-KEY CANADIAN DEALERS BILINGUAL FRENCH/ENGLISH TECHNICAL SUPPORT (514)973-2846 For convenience this document uses short names when referring to a particular system
More information2005 Directed Electronics, Vista, CA N563A 07-05
Model AM7 Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may result
More informationAn ISO 9001:2008 Registered Company
An ISO 9001:2008 Registered Company CVC501-A HVAC & Fast Idle CAN Vehicle Controller CVC502-A HVAC Control without Fast Idle 2011-2016 Ford F250-F550 (CVC501/502-A) 2017 Ford F-250-F550 (B-CVC501/502-A)
More informationMatrix RS Installation Guide
Matrix RS Installation Guide 2001 Directed Electronics, Inc. N909552 8-01 Rev. N/C 1.1 The Bitwriter (p/n 998T) requires chip version 1.4 or newer to program this unit. Bitwriter, Code Hopping, DEI, Directed,
More information2005 Directed Electronics, Inc. Vista, CA N412V 01-05
Model 211HV Installation Guide NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional may
More informationCANBUS Emulator Mini V1.x. Overview - Installation and Operating Instructions
CANBUS Emulator Mini V1.x Overview - Installation and Operating Instructions Contents Overview... 2 Installation... 3 Basic Install... 3 With optional speed sensor input and reverse signal input... 3 Operation...
More informationVehicle Security System
Installation Instructions Vehicle Security System PROFESSIONAL INSTALLATION STRONGLY RECOMMENDED Installation Precautions: Roll down window to avoid locking keys in vehicle during installation Avoid mounting
More informationINSTALLATION GUIDE. FCC ID NOTICE
REV.5 RS. ADVANCED REMOTE STARTER INSTALLATION GUIDE www.security.soundstream.com FCC ID NOTICE This device complies with Part 5 of the FCC rules. Operation is subject to the following conditions:. This
More informationREAD ME FIRST TECHNICAL SUPPORT FORD-KEY CANADIAN DEALERS BILINGUAL FRENCH/ENGLISH TECHNICAL SUPPORT (514) For convenience this document
READ ME FIRST TECHNICAL SUPPORT 1-800-FORD-KEY CANADIAN DEALERS BILINGUAL FRENCH/ENGLISH TECHNICAL SUPPORT (514)973-2846 For convenience this document uses short names when referring to a particular system
More information"WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV
"WE'VE GOT THE EDGE ON SECURITY" INSTALLATION MANUAL AL-700 ATV / AL-900 ATV / AL-1000 ATV COPYRIGHT: OMEGA RESEARCH & DEVELOPMENT INC. 1997 Contents 5 WIRE HARNESS CONNECTIONS Black Wire (Chassis Ground)...
More informationModel K20 installation guide. ProSecurity
Model K20 installation guide ProSecurity NOTE: This product is intended for installation by a professional installer only! Any attempt to install this product by any person other than a trained professional
More informationVS CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.
VS 200 4-CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 200 1 INSTALLATION DIAGRAM Two Way Transceiver Antenna H7 8 Pin Black Connector
More informationEXTENDED INSTALL GUIDE Revision /2015 FW 51+
AUTOMATIC/MANUAL TRANSMISSION REMOTE STARTER EXTENDED INSTALL GUIDE Revision 4.02-08/2015 FW 51+ 12V CONSTANT IN RED 1 ( + ) 500mA 12V TO STARTER PURPLE 2 ( + ) 500mA 12V TO IGNITION PINK 3 SYSTEM GROUND
More informationRS-850 Remote Engine Starting System INSTALLATION INSTRUCTIONS
RS-850 Remote Engine Starting System INSTALLATION INSTRUCTIONS PRE-INSTALLATION CONSIDERATIONS To ease and reduce installation time, we suggest you READ THIS MANUAL and consider the following points before
More informationMEGA WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM. Installation Manual MEGATRONIX CALIFORNIA, USA MEGA 2500 INSTALL 1
MEGA 2500 2-WAY LCD 4-CHANNEL CAR ALARM SECURITY SYSTEM Installation Manual MEGATRONI CALIFORNIA, USA MEGA 2500 INSTALL 1 MEGA 2500 INSTALL 2 INSTALLATION DIAGRAM H8: 10 Pin White Mini Connector H8 10
More informationModel 2100 Installation Guide
Model 2100 Installation Guide 2001 Directed Electronics, Inc. Vista, CA N2100 4-01 Rev. N/C 1.1 table of contents What Is Included..................... 2 Wiring Quick Reference Guide............ 3 Primary
More informationCS-2011RS Series IV & CS-2015FM / TW1 Series II Super Rage The Informer
CS-2011RS Series IV & CS-2015FM / TW1 Series II Super Rage The Informer INSTALLATION INSTRUCTIONS INTRODUCTION Congratulations on your choice of a Crimestopper combination alarm & remote engine starter.
More informationRS4-7/PS4-7 + (2) + SPDT T3015, T3053
TIP SHEET Installation Tips for your RS4-7/PS4-7 + Honda-SL3 (2) + SPDT T3015, T3053 v1.3 4/25/14 Honda: ( 98-02 Accord), ( 98-01 CRV), ( 98-04 Odyssey), ( 03-04 Pilot) Acura: ( 98-99 EL), ( 98-03 CL),
More information6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM
6R / 5-BUTTON SERIES VEHICLE SECURITY SYSTEM Button 1 Button 2 Button 5 Button 3 Button 4 Standard Features: Two 5-Button Remote Transmitters Status indicator (LED) Valet / override switch Multi-tone siren
More informationAdvanced Remote Vehicle Starting System
INSTALLATION GUIDE 1600 Advanced Remote Vehicle Starting System 1600M AUTOMATIC AND MANUAL TRANSMISSION MODELS WWW.ULTRASTARTERS.COM See website for a full size printable version of this manual. WARNING!!
More informationCS WINDOW CONTROL MODULE
INTRODUCTION: CS-5601 4 WINDOW CONTROL MODULE INSTALLATION & OPERATING INSTRUCTIONS CONGRATULATIONS on your choice of a 4 Window Control Module by Crimestopper Security Products Inc. This booklet contains
More informationINSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.
INSTALLATION MANUAL SL- 72 Two-Way 5-Channel 915Mhz Remote Start Security System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty
More informationRS-351-EDP. Installation Guide
RS-351-EDP Keyless Entry & Remote Start Installation Guide June 25, 2013 Temporary cover. Color cover is in a separate file. Table Of Contents Installation Considerations... 3 6 Pin Main Wire Harness...
More informationINSTALLATION MANUAL. This unit is designed for professional installation only and must be installed by an authorized Silencer dealer.
INSTALLATION MANUAL SL- 3 3-Channel Security with Keyless Entry System This unit is designed for professional installation only and must be installed by an authorized Silencer dealer. For Warranty information:
More informationModel 300 Installation Guide
Model 300 Installation Guide 2000 Directed Electronics, Inc. Vista, CA N431R 3-00 table of contents What Is Included..................... 3 Primary Harness (H1), 12-Pin Connector..... 4 Relay Harness (H2),
More informationINSTALLATION HANDBOOK:
INSTALLATION HANDBOOK: CS-2011RS IV / CS-2012TW1 / CS-2014TW2 : AM/FM Alarm Combo Systems CS-2016FM : FM/FM Alarm Combo System INTRODUCTION Congratulations on your choice of a Crimestopper combination
More informationNISSAN TRUCKS ELECTRONIC CRUISE CONTROL KIT AUTOMATIC & MANUAL TRANSMISSIONS PART NUMBER:
General Applicability This cruise control was tested and verified on: 2008-2011 Nissan Frontier 2008-2011 Nissan Titan This cruise control may not function correctly on unverified vehicles. See www.rostra.com
More informationBATTERY DISCONNECT SERVICE MANUAL
Battery Disconnect provides a simple and safe means of remotely disconnecting batteries of an RV or boat. With a touch of a remote switch, the batteries will be completely disconnected, preventing unwanted
More informationSystem Programming Instructions
System Programming Instructions 1 Transmitter programming: A. Open the driver s door (press and hold in brake pedal on Remote Start only system); NOTE: On vehicles with negative polarity door ajar switch
More informationVS CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY. Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A.
VS 255 4-CHANNEL REMOTE ENGINE STARTER WITH KEYLESS ENTRY Installation And Operation Manual MEGATRONIX CALIFORNIA, U.S.A. VS 255 1 VS 255 2 INTRODUCTION INSTALLER WARNINGS This Remote Starter with Alarm
More information