LUMINAIRE SCHEDULE _CUSiteLightingSchedule_092815_GJ.xls 9/28/2015 WATTS / LUMINAIRE ALTERNATE MANUFACTURERS

Transcription

1 15028_CUSiteLightingSchedule_092815_GJ.xls 9/28/2015 TYPE DESCRIPTION MOUNTING LAMPS BOLLARD LIGHT, IMPACT RESISTANT, FLAT TOP, SEE DETAIL B1 LOUVERS, DARK BRONZE FINISH POLE LIGHT, PEDESTRIAN TYPE, LED SOURCE, FLAT GLASS LENS, TYPE II DISTRIBUTION, SPUN ALUMINUM SEE DETAIL P1 HOUSING WITH REVEALS, DARK BRONZE FINISH, WITH STRAIGHT ROUND STEEL POLE, 14', DARK BRONZE FINISH WL1 LED DIE CAST WALL PACK WITH INTEGRAL EXTRUDED ALUMINUM HEAT SINK, DARK BRONZE FINISH, TYPE IV MEDIUM DISTRIBUTION LUMINAIRE SCHEDULE NOTES: WALL MOUNT. HEIGHT PER DWGS LIGHT ENGINE LED ENGINE, 3414 LUMEN 4000K LIGHT ENGINE 2358 LM 4000K WATTS / LUMINAIRE LUMINAIRE SCHEDULE VOLTAGE EMERGENCY MANUFACTURER CATALOG NUMBER N/A HYDREL 3120 C SERIES BOLLARD N/A KIM LIGHTING HEAD NO. CC-17-A K-277-DB-DBREV POLE NO. KRS A-DB ALTERNATE MANUFACTURERS PRE-BID APPROVED EQUAL N/A LITHONIA DSXW1-LED-10C-700MA-40K-T4M-MVOLT-DDBXD PRE-BID APPROVED EQUAL NOTES

2 3120C LED IMPACT RESISTANT ROUND BOLLARD FLAT TOP CATALOG NUMBER NOTES TYPE Specifications EPA: - - Dia: mm Dia 2 : mm H: mm H 2 : mm Weight - 6" 9" 8" 40" 34" 24 8" 36"LCL 30"LCL 20 LCL DESCRIPTION The 3120C BOLLARD is a low level area lighting luminaire that combines visual appeal with superior performance and unequalled quality. It is designed to work in building perimeter areas and public spaces completing a wide variety of architectural styles. Superior performance extends to the detailed finish of the louvers. Matte black finish of top surface provides IES cut off performance while gloss white on bottom extends reflective light to economize on spacing of fixtures. Custom finish available on top louver surface. The 3120C BOLLARD offers a patented impact resistant mounting and leveling design ensuring life long performance. Four levelling pads within the base mounting plate are easily accessible through the access panel. The levelling pads provide full contact with the concrete pad, providing a high degree of stability. The base mounting plate is fully welded to the bollard post, providing complete structural support from all directions, giving the bollard superior vandal resistance. Motion Sensing Bi-Level Switching (BLS option) is now possible through the use of a fixture-integrated microwave occupancy sensor. Mounted in the head of the fixture, within the sealed light engine compartment, the sensor is protected from moisture damage, as well as potential damage due to vandalism. The sensor provides up to 20 of motion coverage in the 360 deg area around the bollard (see diagram on the next page). When motion is detected bollard will illuminate at full output (72 watts). After approx 5 min, bollard will drop to 19 Watts (660 lumens). ORDERING INFORMATION 3120C H36 8COB 50K MVOLT SYM BL 3120C H36 8COB 50K MVOLT SYM Series Height Lamp type Color Voltage Distribution Options C H24 H36 H42 4COB 1 8COB 20K 30K 40K 50K AMB 2000 K Color Temp 3000 K Color Temp 4000 K Color Temp 5000 K Color Temp 591 Nanometers MVOLT ( volt) SYM Symetrical 360 FT 3 Forward Throw BLS 5,6 GFCI ELN 5,7 Bi-Level Switching (Motion Activated) Receptacle; 120 volt only Emergency Operation ( lumen output; 90 minutes) LDIM 0-10V Dimming (Dims to 10%) IDIM 6 In-line Trailing Edge ELV Dimming (Dims to 40%); 120 volt only BL Finish BL BZ DDB DNA GN GR SND Black Bronze Dark Bronze Natural Aluminum Green Gray Sand STG Steel Gray TVG Terra Verde Green WH White CF Custom Z 8 Zinc Undercoat Optional Louvers Painted 9 /PL Louvers painted to match fixture (top only) MOUNTING Notes: 1 4COB for use with 20K and AMB only, 20K and AMB requires 4COB. 2 Required with ELN or BLS. 3 FT not available with BLS. 4 ELN and BLS not available together. 5 ELN and BLS require 120 or 277 voltage, not MVOLT or Only available with 1320 lumen package. 7 ELN not available on 24 height. 8 Add zinc undercoat for harsh environments. 9 Louvers will be black unless otherwise specified (top only). NOTE: Hydrel Reserves The Right To Modify Specification Without Notice. Any dimension on this sheet is to be assumed as a reference dimension: Used for information purposes only. It does not govern manufacturing or inspection requirements. (ANSI Y ) 9144 Deering Avenue, Second Floor Chatsworth, CA Phone: Fax: Acuity Brands Lighting, Inc. Rev. 10/23/ C COB

3 PERFORMANCE DATA LUMEN OUTPUT Lumen values are from photometric tests performed in accordance with IESNA LM Data is considered to be representative of the configurations shown, within the tolerances allowed by Lighting Facts. Actual performance may differ as a result of end-user environment and application. Contact factory for performance data on any configurations not shown here. Light Engines 3000K 4000K 5000K Distribution SYM SYM SYM Drive Current System Watt APPROXIMATE MOTION SENSOR COVERAGE AREA: Lumens LPW B U G 250* * * K SYM *Used with IDIM and BLS options. LED LIFE: L70/125,000 hours OPERATING TEMPERATURE: -20 C Through 50 C -40 C through 50 C with IDIM & BLS options Lumen Ambient Temperature (LAT) Multipliers Use these factors to determine relative lumen output for average ambient temperatures from 0-40 C ( F). Ambient Lumen Multiplier 0 C 32 F C 50 F C 68 F C 77 F C 86 F C 104 F.98 Projected LED Lumen Maintenance Data references the extrapolated performance projections for the Fixture platform in a 25 C ambient, based on 8400 hours of LED testing (tested per IESNA LM and projected per IESNA TM-21-11). To calculate LLF, use the lumen maintenance factor that corresponds to the desired number of operating hours below. For other lumen maintenance values, contact factory. Operating Hours 0 25,000 50, ,000 Lumen Maintenance Factor Electrical Load Light Engines Drive Current (ma) Current (A) System Watts COB 250mA mA PHOTOMETRIC DIAGRAMS Isocandela plots for 3100 COB To see complete photometric reports or download.ies files for this product, visit SYM Tested in accordance with IESNA LM FT Tested in accordance with IESNA LM FEATURES & SPECIFICATIONS MATERIAL: Copper-free Aluminum, A360. LED ARRAY: 72W and 84W (total system input wattage) Lumen maintenance of individual light sources have been independently tested to IESNA LM-80 standards. VOLTAGE: MVOLT 50/60Hz, 120, 277 or 347 DISTRIBUTION: SYM - Symmetric, FT - Forward Throw LENS: Frosted Borosilicate Glass. POWER SUPPLY: Integrally mounted LED driver run at 300mA, -20 C through 50 C standard. Alternate driver run at 250mA, -40 C through 50 C used with IDIM and BLS. LISTINGS: CSA US, CSA WARRANTY: 5-year limited warranty. Complete warranty terms located at Consult factory for details Actual performance may differ as a result of end-user environment and application. Actual wattage may differ by +/- 5% when operating between V +/- 10%. NOTE: Specifications subject to change without notice. FASTENERS: Stainless Steel. FINISH: Super durable polyester TGIC powder coat finish (standard). Optional zinc undercoat for harsh environments Deering Avenue, Second Floor Chatsworth, CA Phone: Fax: Acuity Brands Lighting, Inc. Rev. 10/23/ C COB

4 Type: Job: Catalog number: CC/CCS17 17" Arm Mounted, Curvilinear, PicoEmitter TM LED revision 11/21/14 kl_cc17aeled_spec.pdf / / / / Mtg. Fixture Electrical Module Finish Options See pages 3-4 See page 2 Select pole from Kim Arms and Poles Selection Guide. If pole is provided by others indicate O.D. for arm fitting. Approvals: Date: Page: 1 of 6 Specifications 17" Diameter 60 Light Emitting Diodes Total System Watts = 64W 8" mm) CC CCS 17" DIA. 4K" (431.8 mm) (114.3 mm) 6" (152.4 mm) 2" (50.8 mm) Arm Cross- Section Housing: Spun aluminum. (Rollformed linear reveals; CC: Three equally spaced reveals, K" wide, separated by K" ribs, J" deep. CCS: One J" groove, J" deep.) Sidewalls have a maximum 1 of taper, and are free of welds or fasteners. A rollformed aluminum flange is hemmed into the bottom providing support for the reflector module. An internal aluminum casting provides for mounting of the electrical module plus reinforcing for side-arm mounting of the fixture. Lens Frame Assembly: One-piece cast aluminum lens frame is attached to the housing by a zinc plated cold rolled steel hinge with a stainless steel pin. Closure is by one self-retained stainless steel screw. A stainless steel self-locking stop arm is provided to hold the lens frame in the open position while servicing. A F" thick clear flat tempered glass lens is fully gasketed by a one-piece extruded and vulcanized silicone gasket. Lens is retained in the frame by removable zinc plated steel clips. Standard Arm Mounting: Arm is one-piece extruded aluminum with internal bolt guides and fully radiussed top and bottom. Luminaire-to-pole attachment is by internal draw bolts, and includes a pole reinforcing plate with wire strain relief. Arm is circular cut to mate with specified round pole. Electronic Module: All electrical components are UL and CSA recognized, mounted on a single plate and factory prewired with quick-disconnect plugs. Module includes a driver, LifeShield temperature control device and surge protector. Electrical module attaches to housing with key hole slots, accessible by opening the lens frame and removing optical module.. Driver is rated for -40 F starting and has a 0-10V dimming interface for multi-level illumination options. Optical Module: Precision, replaceable PicoEmitters are positioned to achieve directional control toward desired task. The entire EmitterDeck mounting assembly fastens to the housing as a one-piece module. Finish/Color: TGIC thermoset polyester powder coat paint, 2.5 mil nominal thickness. Standard colors are Black, Dark Bronze, Light Gray, Stealth Gray, Platinum Silver, or White. Custom colors are available. Listed To: UL 1598 Standard for Luminaires - UL 8750 Standard for Safety for Light Emitting Diode (LED) Equipment for use in Lighting Products and CSA C22.2#250.0 Luminaires. Warranty: Kim Lighting warrants Curvilinear LED products ( Product(s) ) sold by Kim Lighting to be free from defects in material and workmanship for (i) a period of five (5) years for metal parts, (ii) a period of ten (10) years for exterior housing paint finish(s), (iii) a period of six (6) years for LED Light Engines (PicoEmitter reflectors) and, (iv) a period of five (5) years for LED power components (LED Driver, LifeShield temperature control device, surge protector), from the date of sale of such goods to the buyer as specified in Kim Lighting shipment documents for each product. CAUTION: Fixtures must be grounded in accordance with national, state and/ or local electrical codes. Failure to do so may result in serious injury. KIM LIGHTING RESERVES THE RIGHT TO CHANGE SPECIFICATIONS WITHOUT NOTICE KIM LIGHTING EAST GALE AVENUE, CITY OF INDUSTRY, CA TEL: 626/ FAX: 626/

5 Type: Job: CC/CCS17 17" Arm Mounted, Curvilinear, PicoEmitter TM LED revision 11/21/14 kl_cc17aeled_spec.pdf Page: 2 of 6 Standard Features Mounting 3Y configuration is available for round poles only. Plan View: Wall Mount EPA: Cat. No.: 1A 2B 2L 3T 3Y 4C 1W Fixture Cat. No. designates CC/ CCS fixture and light distribution. Electrical Module x 17 A x Light Distribution: Housing: E35 = 350mA CC CCS Distribution: 1 = Type I Full Cutoff Type I Type II Type III Size: TYPE I TYPE ITYPE II TYPE II TYPE III 2 = Type II Full Cutoff 17 = 17 Small 60 LEDs 3 = Type III Full Cutoff 4 = Type IV Full Cutoff A = Arm Mount 5 = Type V Square Full Cutoff TYPE Type IV Type V Type R L = Type L Left Full Cutoff Forward Square Right R = Type R Right Full Cutoff TYPE L Throw TYPE L TYPE R TYPE R One-Way One-Way Left One-Way Left One-Way Right Right Cat. Nos. for Electrical Modules available: 60 LxK x E35 TYPE III TYPE IV Type L TYPE R Left Source: Color Temperature: Voltage: 60 = 60 LED s l 3K = 3000K l 120 = 120V l 4K = 4200K l 208 = 208V l 5K = 5100K l 240 = 240V l 2K = 580nm - Amber l 277 = 277V l 347 = 347V 1 l 480 = 480V 1 1 Due to current unavailability of 347V and 480V drivers, specification of these voltages may feature an integral step-down transformer. Finish TGIC powder coat paint over a titanated zirconium conversion coating. Color: Black Dark Bronze Light Gray Stealth Gray Platinum Silver White Custom Color 2 Cat. No.: BL DB LG SG PS WH CC 2Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description: Polycarbonate Lens Cat. No. L17F Optional Features Clear UV stabilized polycarbonate replaces standard flat glass lens, gasketed and integral with lens frame. CAUTION: Use only when vandalism is anticipated to be high. Useful life is limited by UV discoloration from sunlight. Polycarbonate Lens 2014 KIM LIGHTING EAST GALE AVENUE, CITY OF INDUSTRY, CA TEL: 626/ FAX: 626/

6 Type: Job: CC/CCS17 17" Arm Mounted, Curvilinear, PicoEmitter TM LED revision 11/21/14 kl_cc17aeled_spec.pdf Page: 3 of 6 Optional Features Wall Mounting Cat. No. 1W Select from Mounting on page 2. Wall Mount: A cast mounting plate of 356 alloy, low-copper (<0.6% Cu) aluminum, is mounted to the wall with bolts (by others). Fixture and arm are mounted to a cast 356 alloy aluminum cover plate before attaching to the wall mounting plate. The fixture-arm-cover plate assembly is hooked to the wall mounting plate, and secured with stainless steel screws provided. After mounting to the wall, field splices are made at the opening in the cover plate, then covered by a cast 356 alloy aluminum plate that blends with the cover plate design. Complete fixture-arm-cover plate assembly can therefore be mounted before field splices are made. Cover plate is finished to match arm and fixture powder coat color. Wall Attachment and J-Box by Others Cover Plate Typical Architectural Arm Splice Access Cover 10D" (269.9 mm) 5K" (139.7 mm) 4J" (108 mm) 8L" (222.3 mm) 2L" (69.9 mm) Mounting Plate N" (14.3 mm) CAUTION: Structural integrity of mounting plate attachment to wall is by others. Photocell Control Cat. No. (See right) Factory installed photocell inside housing with a fully gasketed sensor on the side wall. For multiple fixture mountings, one fixture is supplied with a photocell to operate the others. Mounting Configuration: Fixture with Photocell Sensor S slave unit(s) No fixture wattage limit. Cat. No. A-30 A-31 A-32 A-33 A-35 A-34 Line Volts: 120V 208V 240V 277V 347V 480V Photocell Sensor 1A, 1W 2B s s s s s s 2L 3T, 3Y 4C s Neighbor Friendly Optic: Cat. No. NFO Integrated Neighbor Friendly Optic on each PicoEmitter module to completely control unwanted backlight. Most effective with Type III and IV distibutions. TYPE III - NFO TYPE IV - NFO 0-10V Dimming Interface Driver has a 0-10V dimming interface with a dimming range of %. Is compatible with most control systems including Hubbell Building Automation wihubb. Approved dimmers include Lutron Diva AVTV, Lutron Nova NFTV and NTFTV. Note: Not compatible with current sourcing dimmers. Controls compatible via Gray and Purple dimming lead. Fixture Housing Standard Input Black (+) White (-) Green (GND) Gray Dimming Lead (-) Purple Dimming Lead (+) 30 ma Max 2014 KIM LIGHTING EAST GALE AVENUE, CITY OF INDUSTRY, CA TEL: 626/ FAX: 626/

7 CC/CCS17 17" Arm Mounted, Curvilinear, PicoEmitter TM LED revision 11/21/14 kl_cc17aeled_spec.pdf Type: Job: Page: 4 of 6 Optional Features Outdoor Occupancy Sensor Cat. No. (See right) Side Pole Mount Outdoor Occupancy Sensor with 0-10VDC dimming control mounts directly to the underside of the luminaire. Wide 360 pattern. Available in voltages to match luminaire from 120 through 480VAC. Module color available in Black, Gray, or White (Picked at the factory when luminaire color is chosen, black used for dark colors). Field Adjustable Timeout settings for 5, 10, 15, and 30 minutes (Factory default is 5-minutes). Field adjustable unoccupied dimming level, 20%, 50%, 60%, or 70% (Factory default is 50%). One sensor can support multiple units up to 1500 watts. (Wiring from module to luminaire(s) is by-others). Mounted to a cast pole adapter painted to match pole. Cat. No. SCL-R*/ **/ *** Pole Occupancy Sensor up to 16', UNV ( V) or 480V. Specify pole diameter. SCL-S/ **/ *** Pole Occupancy Sensor up to 16', UNV ( V) or 480V. Square pole mount. SCH-R*/ **/ *** Pole Occupancy Sensor up to 30', UNV ( V) or 480V. Specify pole diameter. SCH-S/ **/ *** Pole Occupancy Sensor up to 30', UNV ( V) or 480V. Square pole mount. * Pole Diameter, ** Voltage, *** Color Ordering Example: SCL-R4/277/BL Pole Luminaire Occupancy Sensor Side Pole Mount Detection Pattern Top View for Round Luminaire Mounted on Post Top NOTE: Occupancy detection is blocked directly behind pole. Install occupancy sensor as far away from pole as possible to maximize detection. Outdoor Occupancy Sensor Side Pole Mount Luminaire Pole Occupancy Sensor Sensor Lens Coverage and Detection Patterns SCL to 16' mtg. ht. (3:1 Range ) SCH to 30' mtg. ht. (1.4:1 Range) Y = 16' mtg. ht. for SCL Y = 30' mtg. ht. for SCH X = mounting ht. Side Pole Mount Detection Pattern Top View for Round Luminaire Mounted on Arm NOTE: For 360 coverage, install two occupancy sensors 180 apart on pole Y = 3 x mtg. ht. for SCL Y = 1.4 x mtg. ht. for SCH Side View 96' 16' mtg. 84' DIA.@ 30' mounting ht. Top View 2014 KIM LIGHTING EAST GALE AVENUE, CITY OF INDUSTRY, CA TEL: 626/ FAX: 626/

8 Type: Job: CC/CCS17 17" Arm Mounted, Curvilinear, PicoEmitter TM LED revision 11/21/14 kl_cc17aeled_spec.pdf Page: 5 of 6 Optional Features Accent Reveals Cat. No. (See right) (For CC series only) Three aluminum bands riveted inside the housing reveals. Available in five standard Kim powder coat finishes. Custom colors available. Accent Reveals Color: Black Dark Bronze Light Gray Stealth Gray Platinum Silver White Custom Colors 1 Cat. No.: BL-REV DB-REV LG-REV SG-REV PS-REV WH-REV CC-REV 1 Custom colors subject to additional charges, minimum quantities and extended lead times. Consult representative. Custom color description: Vertical Slipfitter Mounts Cat. No. includes Mounting. Cat. No. (See right) Allows fixture with standard support arm to be mounted to steel poles having a 2" pipe-size steel tenon (2C" O.D. x 4K" min. length). 4" round or square cast aluminum with flush cap, secured by four C" stainless steel set point allen screws. Pole tenon must be field drilled at one set screw location to insure against fixture rotation. Finished to match fixture. NOTE: 3Y only available on round slipfitter. Pole with 2" pipe-size tenon (by others) Vertical Slipfitter Mount by Kim Cat. No. VSF-1A VSF-2B VSF-2L VSF-3T VSF-3Y VSF-4C Round Stainless steel set screws Square Cat. No. Mounting Configuration SVSF-1A 1A - single arm mount SVSF-2B 2B - 2 at 180 SVSF-2L 2L - 2 at 90 SVSF-3T 3T - 3 at 90 3Y - 3 at 120 SVSF-4C 4C - 4 at 90 Horizontal Slipfitter Mount Cat. No. HSF Replaces standard mounting arm with a slipfitter which allows CC/CCS Arm Mount model to be mounted to a horizontal pole davit-arm with 2" pipe-size mounting end (2C" O.D.). Cast aluminum slipfitter with set screw anti-rotation lock. Bolts to housing from inside the electrical compartment using mounting holes for the standard support arm. Davit-arm must be field drilled at a set screw location to insure against fixture rotation. Finished to match fixture and arm. Horizontal Slipfitter Mount Davit-arm with 2" pipe-size fixture mount (by others) Support Arm Cat. No. (See right) Note: Refer to Kim Lighting s Arms & Poles Selection Guide for complete details. Arm View: Swept Swept Upsweep Upsweep Uplift Adjustable Uplift Admustable Solid Arm Hollow Arm Solid Arm Hollow Arm Aluminum Arm Stainless Steel Arm Cat. No.: AA01 AA03 AA05 AA07 AA09 AA KIM LIGHTING EAST GALE AVENUE, CITY OF INDUSTRY, CA TEL: 626/ FAX: 626/

9 CC/CCS17 17" Arm Mounted, Curvilinear, PicoEmitter TM LED revision 11/21/14 kl_cc17aeled_spec.pdf Type: Job: Page: 6 of 6 Lumen Data Spectroradiometric Projected Lumen Maintenance 3000K Average 4200K Average 5100K Average Correlated Color Temp. CCT (K) 2800K-3175K 3800K-4600K 4600K-5600K ma 100,000 hrs (Calculated L70) % 584,00 hrs. Color Rendering Index (CRI) Power Factor >.90 >.90 >.90 Electrical Drive Current Volts - AC Amps - AC System Watts B.U.G. Rating (TM15) in Lumens wher B = Backlight, U = Uplight, G = Glare Temperature TYPE 1 TYPE 2 TYPE 3 TYPE 3 NFO TYPE 4 TYPE 4 NFO TYPE 5 TYPE L/R 3000K B2 U0 G2 B1 U0 G1 B1 U0 G1 B1 U0 G1 B1 U0 G1 B0 U0 G1 B2 U0 G1 TBD 4200K B3 U0 G3 B2 U0 G2 B1 U0 G1 B1 U0 G1 B1 U0 G2 B1 U0 G1 B3 U0 G1 TBD 5100K B3 U0 G3 B2 U0 G2 B1 U0 G1 B1 U0 G1 B1 U0 G2 B1 U0 G1 B3 U0 G1 TBD Absolute Lumens Temperature TYPE 1 TYPE 2 TYPE 3 TYPE 3 NFO TYPE 4 TYPE 4 NFO TYPE 5 TYPE L/R 3000K TBD 4200K TBD 5100K TBD LED performance and lumen output continues to improve at a rapid pace. Log onto to download the most current photometric files from Kim Lighting s IES File Library. For custom optics and color temperature configurations, contact factory KIM LIGHTING EAST GALE AVENUE, CITY OF INDUSTRY, CA TEL: 626/ FAX: 626/

10 6-3/ /4 6-3/8 D-Series Size 1 LED Wall Luminaire Catalog Number Notes Type Hit the Tab key or mouse over the page to see all interactive elements. Introduction Specifications Luminaire Width: 13-3/4 (34.9 cm) Depth: 10 (25.4 cm) Height: 6-3/8 (16.2 cm) W Weight: D 12 lbs (5.4 kg) H Back Box (BBW, ELCW) Width: 13-3/4 (34.9 cm) Depth: 4 (10.2 cm) Height: 6-3/8 (16.2 cm) H D BBW Weight: ELCW Weight: W For 3/4 NPT side-entry conduit (BBW only) 5 lbs (2.3 kg) 10 lbs (4.5 kg) The D-Series Wall luminaire is a stylish, fully integrated LED solution for building-mount applications. It features a sleek, modern design and is carefully engineered to provide long-lasting, energy-efficient lighting with a variety of optical and control options for customized performance. With an expected service life of over 20 years of nighttime use and up to 74% in energy savings over comparable 250W metal halide luminaires, the D-Series Wall is a reliable, low-maintenance lighting solution that produces sites that are exceptionally illuminated. Ordering Information EXAMPLE: DSXW1 LED 20C K T3M MVOLT DDBTXD DSXW1 LED Series LEDs Drive Current Color temperature Distribution Voltage Mounting Control Options Other Options Finish (required) DSXW1 LED 10C 10 LEDs (one engine) 20C 20 LEDs (two engines) ma ma ma ma (1 A) 30K 40K 50K AMBPC 3000 K 4000 K 5000 K Amber phosphor converted T2S T2M T3S T3M T4M TFTM ASYDF Type II Short Type II Medium Type III Short Type III Medium Type IV Medium Forward Throw Medium Asymmetric diffuse MVOLT Shipped included (blank) Surface mounting bracket BBW Surfacemounted back box (for conduit entry) 3 Shipped installed PE Photoelectric cell, button type 4 DMG 0-10V dimming driver (no controls) PIR 180 motion/ ambient light sensor, <15 mtg ht 5 PIRH 180 motion/ ambient light sensor, mtg ht 5 ELCW Emergency battery backup (includes external component enclosure) 6 Shipped installed SF Single fuse (120, 277 or 347V) 7 DF Double fuse (208, 240 or 480V) 7 HS House-side shield 8 SPD Separate surge protection 9 Shipped separately BSW Bird-deterrent spikes WG Wire guard VG Vandal guard DDL Diffused drop lens DDBXD Dark bronze DBLXD Black DNAXD Natural aluminum DWHXD White DSSXD Sandstone DDBTXD Textured dark bronze DBLBXD Textured black DNATXD Textured natural aluminum DWHGXD Textured white DSSTXD Textured sandstone NOTES 1 MVOLT driver operates on any line voltage from V (50/60 Hz). Specify 120, 208, 240 or 277 options only when ordering with fusing (SF, DF options), or photocontrol (PE option). 2 Only available with 20C, 700mA or 1000mA. Not available with PIR or PIRH. 3 Back box ships installed on fixture. Cannot be field installed. Cannot be ordered as an accessory. 4 Photocontrol (PE) requires 120, 208, 240, 277 or 347 voltage option. Not available with motion/ambient light sensors (PIR or PIRH). 5 PIR specifies the Sensor Switch SBGR-10-ODP control; PIRH specifies the Sensor Switch SBGR-6-ODP control; see Motion Sensor Guide for details. Includes ambient light sensor. Not available with PE option (button type photocell). Dimming driver standard. Not available with 20 LED/1000 ma configuration (DSXW1 LED 20C 1000). 6 Cold weather (-20C) rated. Not compatible with conduit entry applications. Not available with BBW mounting option. Not available with fusing. Not available with 347 or 480 voltage options. Emergency components located in back box housing. Emergency mode IES files located on product page at 7 Single fuse (SF) requires 120, 277 or 347 voltage option. Double fuse (DF) requires 208, 240 or 480 voltage option. Not available with ELCW. 8 Also available as a separate accessory; see Accessories information. 9 See the electrical section on page 3 for more details. Accessories Ordered and shipped separately. DSXWHS U House-side shield (one per light engine) DSXWBSW U Bird-deterrent spikes DSXW1WG U Wire guard accessory DSXW1VG U Vandal guard accessory One Lithonia Way Conyers, Georgia Phone: Fax: Acuity Brands Lighting, Inc. All rights reserved.

11 Performance Data Lumen Output Lumen values are from photometric tests performed in accordance with IESNA LM Data is considered to be representative of the configurations shown, within the tolerances allowed by Lighting Facts. Contact factory for performance data on any configurations not shown here. LEDs 10C (10 LEDs) 20C (20 LEDs) Drive Current (ma) 530mA 700mA 1000mA 530mA 700mA 1000mA System Watts 20 W 27 W 40 W 36 W 47 W 74 W Dist. Type 30K 40K 50K AMBER Lumens B U G LPW Lumens B U G LPW Lumens B U G LPW Lumens B U G LPW T2S 1, , , T2M 1, , , , T3S 1, , , , T3M 1, , , , T4M 1, , , , TFTM 1, , , , ASYDF 1, , , , T2S 2, , , , T2M 2, , , , T3S 2, , , , T3M 2, , , , T4M 2, , , , TFTM 2, , , , ASYDF 2, , , , T2S 3, , , , T2M 2, , , , T3S 2, , , , T3M 2, , , , T4M 2, , , , TFTM 3, , , , ASYDF 2, , , , T2S 3, , , , T2M 3, , , , T3S 3, , , , T3M 3, , , , T4M 3, , , , TFTM 3, , , , ASYDF 3, , , , T2S 4, , , , T2M 4, , , , T3S 4, , , , T3M 4, , , , T4M 4, , , , TFTM 4, , , , ASYDF 4, , , , T2S 5, , , , T2M 5, , , , T3S 5, , , , T3M 5, , , , T4M 5, , , , TFTM 5, , , , ASYDF 5, , , , One Lithonia Way Conyers, Georgia Phone: Fax: Acuity Brands Lighting, Inc. All rights reserved. DSXW1-LED Rev. 4/14/15

12 Performance Data Lumen Ambient Temperature (LAT) Multipliers Use these factors to determine relative lumen output for average ambient temperatures from 0-40 C ( F). Ambient Lumen Multiplier 0 C 32 F C 50 F C 68 F C 77 F C 86 F C 104 F 0.98 Projected LED Lumen Maintenance Data references the extrapolated performance projections for the DSXW1 LED 20C 1000 platform in a 25 C ambient, based on 10,000 hours of LED testing (tested per IESNA LM and projected per IESNA TM-21-11). Electrical Load LEDs 10C 20C Drive Current (ma) System Watts Current (A) 120V 208V 240V 277V 347V 480V W W W W W W W W To calculate LLF, use the lumen maintenance factor that corresponds to the desired number of operating hours below. For other lumen maintenance values, contact factory. Operating Hours 0 25,000 50, ,000 Lumen Maintenance Factor Photometric Diagrams To see complete photometric reports or download.ies files for this product, visit Lithonia Lighting s D-Series Wall Size 1 homepage. Isofootcandle plots for the DSXW1 LED 20C K. Distances are in units of mounting height (15 ). Distribution overlay comparison to 250W metal halide. LEGEND 0.1 fc 0.5 fc 1.0 fc T2M Test No P22 tested in accordance with IESNA LM T3M Test No P22 tested in accordance with IESNA LM T3S Test No P22 tested in accordance with IESNA LM LEGEND DSXW1, 0.5 fc TWF2, 0.5 fc 10 W Sidewalk LLDs: TWF2 = 0.72 DSXW1 = 0.95 TWF2: 291W DSXW1 LED 20C 40K 1000 T3M, TWF2 250M Pulse, 15 Mounting Ht DSXW1: 75W Options and Accessories T3M (left), ASYDF (right) lenses HS - House-side shields BSW - Bird-deterrent spikes WG - Wire guard VG - Vandal guard DDL - Diffused drop lens FEATURES & SPECIFICATIONS INTENDED USE The energy savings, long life and easy-to-install design of the D-Series Wall Size 1 make it the smart choice for building-mounted doorway and pathway illumination for nearly any facility. CONSTRUCTION Two-piece die-cast aluminum housing has integral heat sink fins to optimize thermal management through conductive and convective cooling. Modular design allows for ease of maintenance. The LED driver is mounted to the door to thermally isolate it from the light engines for low operating temperature and long life. Housing is completely sealed against moisture and environmental contaminants (IP65). FINISH Exterior parts are protected by a zinc-infused Super Durable TGIC thermoset powder coat finish that provides superior resistance to corrosion and weathering. A tightly controlled multi-stage process ensures a minimum 3 mils thickness for a finish that can withstand extreme climate changes without cracking or peeling. Available in textured and non-textured finishes. OPTICS Precision-molded proprietary acrylic lenses provide multiple photometric distributions tailored specifically to building mounted applications. Light engines are available in 3000 K (80 min. CRI), 4000 K (70 min. CRI) or 5000 K (70 CRI) configurations. ELECTRICAL Light engine(s) consist of 10 high-efficacy LEDs mounted to a metal-core circuit board to maximize heat dissipation and promote long life (L88/100,000 hrs at 25 C). Class 1 electronic drivers have a power factor >90%, THD <20%, and a minimum 2.5KV surge rating. When ordering the SPD option, a separate surge protection device is installed within the luminaire which meets a minimum Category C Low (per ANSI/IEEE C ). INSTALLATION Included universal mounting bracket attaches securely to any 4 round or square outlet box for quick and easy installation. Luminaire has a slotted gasket wireway and attaches to the mounting bracket via corrosion-resistant screws. LISTINGS CSA certified to U.S. and Canadian standards. Rated for -40 C minimum ambient. DesignLights Consortium (DLC) qualified product. Not all versions of this product may be DLC qualified. Please check the DLC Qualified Products List at to confirm which versions are qualified. WARRANTY Five year limited warranty. Full warranty terms located at CustomerResources/Terms_and_conditions.aspx. Note: Actual performance may differ as a result of end-user environment and application. All values are design or typical values, measured under laboratory conditions at 25 C. Specifications subject to change without notice. One Lithonia Way Conyers, Georgia Phone: Fax: Acuity Brands Lighting, Inc. All rights reserved. DSXW1-LED Rev. 4/14/15