JACOBSEN. Parts & Fitting Instruction Manual. LF3400 Mauser Cab JACOBSEN. Product codes: LMAB875 Mauser

Transcription

1 JACOBSEN Parts & Fitting Instruction Manual LF3400 Mauser Cab Product codes: LMAB875 Mauser WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the entire manual before attempting to set up, operate, adjust or service the machine. JACOBSEN (RJ ) Part No.24427G (rev.0)

2 2000, Textron Inc. All Rights Reserved

3 1 CONTENTS CONTENTS PAGE 2 SAFETY INSTRUCTIONS 2.1 OPERATING INSTRUCTIONS SAFETY SIGNS STARTING THE ENGINE DRIVING THE MACHINE TRANSPORTING LEAVING THE DRIVING POSITION SLOPES BLOCKED CUTTING CYLINDERS ADJUSTMENTS, LUBRICATION & MAINTENANCE SPECIFICATIONS 3.1 DIMENSIONS WITH CAB VIBRATION & NOISE LEVEL WITH CAB SLOPES CONFORMITY & NOISE EMISSIONS CERTIFICATES METRIC TORQUE SETTINGS CAB FITTING INSTRUCTIONS NOISE REDUCTION KIT FITTING INSTRUCTIONS WINDSCREEN WASHER FITTING INSTRUCTIONS ADDITIONAL LIGHTING KIT FITTING INSTRUCTIONS BALANCE WEIGHT KIT FITTING INSTRUCTIONS STATIC LAP BELT PARTS LIST 11.1 CAB FRAME FRONT GLASS REAR GLASS DOOR / SIDE WINDOW ROOF INSERT ROOF MOUNTING PARTS TARPAULIN COVERING ADDITIONAL LIGHTING ROTATING LIGHT WINDOW SCREEN WASHER NOISE REDUCTION KIT WEIGHT KIT DECALS GUARANTEE / SALES & SERVICE

4 2 SAFETY INSTRUCTIONS This safety symbol indicates important safety messages in this manual. When you see this symbol, be alert to the possibility of injury, carefully read the message that follows, and inform other operators. 2.1 OPERATING INSTRUCTIONS Ensure that the instructions in this book are read and fully understood. No person should be allowed to operate this machine unless they are fully acquainted with all the controls and the safety procedures. Never allow children or people unfamiliar with these instructions to use this machine. Local regulations may restrict the age of the operator. 2.2 SAFETY SIGNS It is essential all safety labels are kept legible, if they are missing or illegible they must be replaced. If any part of the machine is replaced and it originally carried a safety label, a new label must be affixed to the replacement part. New safety labels are obtainable from Ransomes dealers. 2.3 STARTING THE ENGINE Before starting the engine check that the brakes are applied, drives are in neutral, guards are in position and intact, and bystanders are clear of the machine. Do not run the engine in a building without adequate ventilation. 2.4 DRIVING THE MACHINE Before moving the machine, check to ensure that all parts are in good working order, paying particular attention to brakes, tyres, steering and the security of cutting blades. Replace faulty silencers, mow only in daylight or good artificial light Always observe the Highway Code both on and off the roads. Keep alert and aware at all times. Watch out for traffic when crossing or near roadways. Stop the blades rotating before crossing surfaces other than grass. Remember that some people are deaf or blind and that children and animals can be unpredictable. Keep travelling speeds low enough for an emergency stop to be effective and safe at all times, in any conditions. Remove or avoid obstructions in the area to be cut, thus reducing the possibility of injury to yourself and/or bystanders. When reversing, take special care to ensure that the area behind is clear of obstructions and/or bystanders. DO NOT carry passengers. Keep in mind that the operator or user is responsible for accidents or hazards occurring to other people or their property. When the machine is to be parked, stored or left unattended, lower the cutting means unless the transport locks are being used. While mowing, always wear substantial footwear and long trousers. Do not operate the equipment when barefoot or wearing open sandals. Check the grass catcher frequently for wear or deterioration. After striking a foreign object. Inspect. the lawnmower for damage and make repairs before restarting and operating the equipment. If the machine starts to vibrate abnormally, check immediately. 2.5 TRANSPORTING Ensure that the cutting units are securely fastened in the transport position. Do not transport with cutting mechanism rotating. Drive the machine with due consideration of road and surface conditions, inclines and local undulations. 2.6 LEAVING THE DRIVING POSITION Park the machine on level ground. Before leaving the driving position, stop the engine and make sure all moving parts are stationary. Apply brakes and disengage all drives. Remove the starter key. 2.7 SLOPES TAKE EXTRA CARE WHEN WORKING ON SLOPES Local undulations and sinkage will change the general slope. Avoid ground conditions which can cause the machine to slide. Keep machine speeds low on slopes and during tight turns. Remember there is no such thing as a safe slope. Travel on grass slopes requires particular care. -2

5 2 SAFETY INSTRUCTIONS 2.8 BLOCKED CUTTING CYLINDERS Stop the engine and make sure all moving parts are stationary. Apply brakes and disengage all drives. Release blockages with care. Keep all parts of the body away from the cutting edge. Beware of energy in the drive which can cause rotation when the blockage is released. Keep other people away from the cutting units as rotation of one cylinder can cause the others to rotate. 2.9 ADJUSTMENTS, LUBRICATION AND MAINTENANCE Stop the engine and make sure all moving parts are stationary. Apply brakes and disengage all drives. Read all the appropriate servicing instructions. Use only the replacement parts supplied by the original manufacturer. When adjusting the cutting cylinders take care not to get hands and feet trapped when rotating cylinders. Make sure that other people are not touching any cutting units, as rotation of one cylinder can cause the others to rotate. To reduce the fire hazard, keep the engine, silencer and battery compartments free of grass, leaves or excessive grease. Replace worn or damaged parts for safety. When working underneath lifted parts or machines, make sure adequate support Is provided. Do not dismantle the machine without releasing or restraining forces which can cause parts to move suddenly. DANGER - Indicates an imminently hazardous situation which, if not avoided, WILL result in death or serious injury. WARNING - Indicates a potentially hazardous situation which, if not avoided, COULD result in death or serious injury. CAUTION - Indicates a potentially hazardous situation which, if not avoided, MAY result in minor or moderate injury and property damage. It may also be used to alert against unsafe practices. WARNING Hydraulic Fluid escaping under pressure can penetrate skin and do serious damage. Immediate medical assistance must be sought. -3

6 3 SPECIFICATIONS 3.1 DIMENSIONS WITH CAB Width of cut: metres (115in) Transport width: metres (87in) Overall height: metres (80.7in) Overall length: mtres (120in) Overall weight of machine: 1545Kg (3406lbs)* * With 7 knife units, full fuel tank, and optional Lighting and Beacon kits 3.2 VIBRATION and NOISE LEVEL WITH CAB The machine was tested for whole body and hand/arm vibration levels. The operator was seated in the normal operating postion with both hands on the steering mechanism. The engine was running and the cutting device was rotating with the machine stationary. Hand / Arm acceleration level : m/s 2 Floor Location Seat Location x y z x y z Mean Noise emisions conform to the specification of Directive EEC79/113, 84/558, 87/252, 88/181. Sound Power Level: 83.2 db(a) Lpa (Operator) with windows closed,doors Shut and No Air Conditioning db(a) Lpa (Operator) with windows closed,doors Shut and Air Conditioning db(a) Lpa (Operator) with windows Open, Doors Shut and No Air Conditioning. 3.3 SLOPES DO NOT USE ON SLOPES GREATER THAN 15 The slope 15 was calculated using static stability measurements according to the requirements of EN

7 3 SPECIFICATIONS 3.4 CONFORMITY CERTIFICATES NOISE EMISSION CERTIFICATE OF CONFORMITY We, the undersigned Ransomes Jacobsen Limited Ransomes Way, Ipswich, England IP3 9QG Certify that the lawnmower Category: Ride-on cylinder mower Make: Jacobsen Type: LF3400 4wd Fairway Mower with Mauser ROPS Cab (LMAB875) Motor:- Manufacturer: Kubota Type: V1305-E Speed of rotation during the test: 3131 r.p.m. Conforms to the specification of directive EEC 79/113 84/538 87/252 88/180 88/181 GUARANTEED Sound pressure : Windows closed, A/Con off 83.2dB(A) Lpa Windows closed, A/Con on 82.4dB(A) Lpa Windows Open, A/Con off 85.4dB(A) Lpa Type of cutting device: 5 Cylinder, 7 Blades Width of cut: metres (115in) Speed of rotation of the cutting device: 2071r.p.m. Test Completed at: Ransomes Jacobsen Ltd, Central Avenue, Ransomes Europark Ipswich, IP3 9QG 15th September 1999 Report No. C/99/5L/7733/3 S. Chicken Director of Engineering EC Declaration of Conformity We the undersigned Ransomes Jacobsen Limited Central Avenue, Ransomes Europark Ipswich, England, IP3 9QG Certify that the lawnmower Make: Jacobsen Type: LF3400 Series: wd Fairway Mower fitted with Mauser ROPS cab LMAB875 Conforms to EC directives and amendments: 98/37/EEC, Machinery Safety Directive 89/336/EEC, EMC 79/622/EEC, ROPS static test. Standard: EN836 17th MAY 2000 S. Chicken Director of Engineering -5

8 4 METRIC TORQUE SETTINGS METRIC FASTENERS Noncritical Fasteners into SIZE UNITS Aluminum M4 Nm (in-lb) 1.2 (11) 1.7 (15) 2.9 (26) 4.1 (36) 5.0 (44) 2.0 (18) M5 Nm (in-lb) 2.5 (22) 3.2 (28) 5.8 (51) 8.1 (72) 9.7 (86) 4.0 (35) M6 Nm (in-lb) 4.3 (38) 5.7 (50) 9.9 (88) 14.0 (124) 16.5 (146) 6.8 (60) M8 Nm (in-lb) 10.5 (93) 13.6 (120) 24.4 (216) 33.9 (300) 40.7 (360) 17.0 (150) M10 Nm (ft-lb) 21.7 (16) 27.1 (20) 47.5 (35) 66.4 (49) 81.4 (60) 33.9 (25) M12 Nm (ft-lb) 36.6 (27) 47.5 (35) 82.7 (61) (86) (103) 61.0 (45) M14 Nm (ft-lb) 58.3 (43) 76.4 (55) (97) (136) (162) 94.9 (70) -6

9 5 CAB FITTING INSTRUCTIONS NOTE : For Cab Parts List Refer to SECTION 11 Sub-sections 11.1 to 11.8 ALL BOLTS MUST BE TORQUED UP TO THEIR SPECIFIC TORQUE SETTINGS. REFER TO SECTION Using M12 x 20 Hex Set Screws and washers, bolt the cab supports (Part 6) onto the left and right positions in the middle of the frame, and tighten up. 5.2 Using M8 x 25 Hex Set Screws, M8 Hex Full Nuts and washers. Bolt the cab supports (Parts 1 & 2) onto the left and right positions at the front of the frame, at the position indicated with a B. Using a 8.5mm drill, drill additional holes in the frame, by using the holes in the cab supports as guides where indicated. Finish bolting the cab supports to the frame using bolts supplied. 1 & 2 DRILL HERE B 5.3 Using a safe method, lift the cab onto the vehicle, locating the cab onto the supports. Install rubber sealing before bolting down cab. Insert the Bolt - Hex (Part 16) M10 x 100 with washers through the four corners of the cab and the rubber supports Place one of the white pressure plates (Part 13) on to each of the undersides of rubber supports. 16 Screw on one of the Nut - Hex M10 (Part 14) onto each of the Hex Set Screws M10 x 100 and tighten up

10 5 CAB FITTING INSTRUCTIONS 5.4 Connect cable: Lay cable for trip current red/black and line cable (white insulation) back to the engine compartment. Unscrew the control Box. Lay red/black cable to ignition Switch. Pin on with orange original cable (double plug). 5.5 Connect line cable on battery. Red = positive, brown = negative. Fix cable securely using cable clips. 5.6 Connect heating: only version with heater Lay heating hoses back to engine compartment. Drain out some of the cooling water from the cooling system. HOSE TAIL FITTING Unscrew the screw plug on thermostat housing and replace with Hose-Tail Fitting. 5.7 Cut through hose which joins the thermostat to the Radiator. Insert the T-piece into the two halves of the pipe. Fix heating hoses securely by using cable tapes. CUT HERE & ADD TEE PIECE -8

11 5 CAB FITTING INSTRUCTIONS 5.8 Refill the cooling system using correct 50/50 mix of anti-freeze and water. 5.9 Start the engine Open shut-off cock and let engine run (half throttle) until warm air flows out of the heater Check the heating system for leaks once the heating has been run When the engine has cooled down sufficiently top-up the cooling system with a 50/50 mix of antifreeze and water Service notes! You have to check the heating equipment including tubes and connections, at least once a year for tightness The intake filter should be cleaned at least half- yearly. If dusty working conditions, more often. Attention! Use a pollutant filter if any chemicals have been used on the area to be cut. During summer operation, the water heater can be stopped by closing the shut-off cock. The heating fan can then be used as a blower. WARNING Attach hoses with cable tapes to non-moving parts. Do not lay hoses near exhaust Access to the engine-hood latch is through the opening in the middle of rear Installation sheet behind the drivers seat. WARNING Once a ROPS Cab has been fitted to a machine, ballast weights, Static Lap Belt & Replacement Decals must be fitted to the machine. Refer to the Weight Kit Fitting Instructions SECTION 11 Subsection Attention!! You may not clamp additional consumer items to the cabin cable - assembly, ONLY Mauser accessories. -9

12 6 CAB NOISE REDUCTION KIT For Cab Noise Reduction Kit Parts List Refer to SECTION 11 Subsection NOTE : ALL BOLTS MUST BE TORQUED UP TO THEIR SPECIFIC TORQUE SETTINGS. REFER TO SECTION Place the foam pad (Part 10) onto the platform of the vehicle Lay the small piece of foam pad ( Part 9) on the front left hand side in front of cabfastening screw

13 6 CAB NOISE REDUCTION KIT 6.3 Place the rubber floor mat (Part 8) onto the floor of the cabin. Turn cut out in floor mat over the pedals Assemble self-adhesive stipple sandwich foam 3-parts. Stick (Part 1) on rear sheet. Stick (Part 6) (6 cm) behind seat under platform Stick (Part 7) behind seat on the vertical area of platform

14 6 CAB NOISE REDUCTION KIT 6.5 If not prefabricated, rivet protecting strips (Parts 4 & 5) on the cab laterals, below the left-hand and right-hand side cab windows (dismantle side glass first) Stick the self-adheasive stipple sandwich foam (Parts 2 & 3) on the left and right side walls of the cab ATTENTION! THE DECAL STICKERS FOR OPERATION - AND SAFETY INSTRUCTIONS, WHICH ARE COVERED BY THE MATTING, MUST BE REPLACED. PLACE THEM IN A CLEAR VISIBLE PLACE TO ENSURE THE OBSERVATION OF THE SAFETY INSTRUCTIONS ARE ADHERED TO. -12

15 7 WINDSCREEN WASHER For Windscreen Washer Parts List Refer to SECTION 11 Subsection NOTE : ALL BOLTS MUST BE TORQUED UP TO THEIR SPECIFIC TORQUE SETTINGS REFER TO SECTION Using a safe method dismantle roof from the cab. 7.2 Screw washer tank (Part 2) on rear sheet behind the operator position. 2 If the rear stipple sandwich foam has been fitted, use distance sleeves and longer screws. 7.3 Lead hose and cable from heater console through backup below. 2 Connect cable: Connect the red cable to the wiper switch into position 3 (according to number of switch). 8 4 Connect brown cable to ground bar Screw nozzle (Part 6) on front plate above the front screen directing the nozzle down towards the windscreen. 6-13

16 7 WINDSCREEN WASHER 7.5 Using a safe method reassemble roof onto the cab. OPERATIONAL CHECK: Fill reservoir with the correct mixture of water and screen wash. Check that the washer works and adjust nozzle direction. Check for any leakage. -14

17 8 ADDITIONAL LIGHTING For Cab Noise Reduction Kit Parts List Refer to SECTION 11 Subsection NOTE : ALL BOLTS MUST BE TORQUED UP TO THEIR SPECIFIC TORQUE SETTINGS. REFER TO SECTION Using a safe method dismantle roof from the cab. Dismantle the front filter cover above the front screen. Remove the closing plugs from the front plate above the front screen. 8.2 Press the rubber-protecting sleeve in hole (Part 12) and lay cable (Part 6) inwards. Mount the headlights (Parts 2 & 3) onto the front plate of the cab & Press the light switch (Part 9) into the heating console above the operator position and connect the cable. Connect the red cable onto the fuse box in position number 3 and the brown cable on to the earth bar. Press the 10-amp fuse (Part11) into the fuse box in position number 3 for the lights. Lay and screw on 2-pole plug on headlights. 9 FUSE BOX 8.4 Using a safe method reassemble roof onto the cab. CAUTION Make sure that you do not catch any cables or hoses. -15

18 9 BALANCE WEIGHT KIT For Balance Weight Kit Parts List Refer to SECTION 19 Subsection NOTE : ALL BOLTS MUST BE TORQUED UP TO THEIR SPECIFIC TORQUE SETTINGS REFER TO SECTION Access to the engine-hood latch is through the opening in the middle of rear sheet REFER TO SECTION Lift up the engine cover. 9.2 Looking at the machines from the rear. Hook the Left-hand & Right-hand Brackets (Parts 2 & 3) onto the rear of the frame. 2 & Using the M16 Hex-bolts (Part 4) & Washers (Part 6) provided, slide the Weights 2 off onto the Hex-bolts. Lift the Balance Weights (Part 1) up to the Brackets & Screw the M16 Hex-Bolts into the Brackets. Screw the M16 hex Full Nuts (Part 5) onto the threads at the back of the Brackets, locking the M16 Hex-Bolts into place Wheel Weights 9.4 Assemble extension onto the inflation valve on the wheel. Remove the two wheel mounting bolts, which are 180 O apart, to allow the cut out in the wheel weight to fit over the inflation valve. Position the Wheel Weight inside the wheel hub and secure into place by using the two new ½ - 20 x 2 ½ inch UNF long Bolts and Lockwashers. Torque the 2 ½ Bolt to ft. lbs ( Nm). Note: Retorque after 20 hours use. Inflation Valve Bolt wheel weight -16

19 10 STATIC LAP BELT NOTE : ALL BOLTS MUST BE TORQUED UP TO THEIR SPECIFIC TORQUE SETTINGS. REFER TO SECTION Using the bolt provided, bolt the clasp part ofthe belt onto the right-hand side of the seat. Make sure that the bolt is securely tightend up Using the bolt provided, bolt the buckle part ofthe belt onto the left-hand side of the seat. Make sure that the bolt is securely tightend up. -17

20 11 PARTS LIST 11.1 CAB FRAME / / /16-18

21 11 PARTS LIST 11.1 CAB FRAME No Part No Description Qty Remarks Frame 1 2 P Seal H = 5.5, B = 9mm, 3.0m ( ) SET 3 P Seal 29 x 39mm 0.8m ( ) SET 4 P Seal H = 30, 6.0m ( ) SET 5 P Seal 2.86m ( ) SET 6 P Seal 2.12m SET Cover 1 8 P Seal H = 5.5, B = 9mm, 2.0m ( ) SET Screw M 6 x 16 DIN Washer 6,4 x Nut M Cover 1 13 P Buckle 20mm ( & ) 0.6m SET Molding 215mm P Striker ( ) SET Ballstud 2 19 P Support right L = 260mm SET 20 P Support left L = 260mm SET Mirror Fuse Box Cap Fuse 30A Fuse 30A 1 26 P Hook SET -19

22 11 PARTS LIST 11.2 FRONT GLASS No Part No Description Qty Remarks Glass B = 771, H = 750, 4L Label 87 x 28mm 1 3 P Hinge M8 x 17 SET Screw M8 x 25 DIN 933, P Window Opener L = 195mm SET Glass B = 820, H = 336, 4L 2 7 P Glass Fixation 2 x M8 x 17 SET Wiper Motor 12V, Nm Wiper Arm 360mm Wiper Blade 530mm Cable 1-20

23 11 PARTS LIST 11.3 REAR GLASS No Part No Description Qty Remarks 1 P Glass+Enclosure right-hand SET Glass B = 1054, H = 606, 4L 1 3 P Gasket 3.23m LONG SET 4 P Hinge M8 x 17 SET Screw M8 x 16 DIN 933, Screw M8 x 25 DIN 933, Disk 8, 4 x 18 DIN Nut M8 DIN 985, Cap M P Window Opener L = 115mm SET -21

24 11 PARTS LIST 11.4 DOOR / SIDE WINDOW /32 7/ / / / / /16 6 1/2-22

25 11 PARTS LIST 11.4 DOOR / SIDE WINDOW No Part No Description Qty Remarks Door Right-hand Door Left-hand 1 3 P Glass+Enclosure Riight-hand SET 4 P Glass+Enclosure Left-hand. SET Glass B = 882, H = 1165, 9L 2 6 P Seal 4.08m LONG ( ) SET Hinge above Right-hand Hinge above Left-hand Hinge below Right-hand Hinge below Left-hand P Screw 1 x M8 x 32 SET 12 P Door Outside Latch M6 x 25 SET Handle M Rubber Safety Lock Right-hand Safety Lock Left-hand Cover Right-hand Cover Left-hand Button L = 59mm Terminal Nipple M BallSlud Bracket Bracket Hydropneumatic Spring L = 320mm 100N Rubber Boil Right-hand Boil Left-hand W Locking Device SET 31 P Glass + Enclosure Right-hand SET 32 P Glass + Enclosure Left-hand SET Glass B = 593, H = P Gasket 2.6m LONG ( ) SET Fixing Fixing Screw Fixing Rivet 4 x

26 11 PARTS LIST 11.5 ROOF INSERT /

27 11 PARTS LIST 11.5 ROOF INSERT No Part No Description Qty Remarks 1 P Roof Console Nozzle D = 100mm Shield 2 4 P Sun Visor SET Lamp Bulb 12 Volt 5W Relay 12 Volt Tap 1/4" Bracket Handle Bracket Orifice Switch Switch Grate Emblem Emblem Hose 1/2" 4,6 m Clip 11-17mm Hose 1/2" 5,2 m Handle Buckle Buckle Spring L = 77mm Linkage Join Cross AS 10 M Flap Heater 12Volt Connecting Socket R 3/8" Elbow Clip 32-44mm Filter 600 x 107 x56mm Coal Filter Bracket Cover Spring 2 37 P Bracket SET Fuse Box Recept. Connect Body Fuse 7.5A Fuse 5A Orifice Flexible Tube 23mm x 0,5 m Heater Tie Band 145mm Cable Cable Cable 1-25

28 11 PARTS LIST 11.6 ROOF No Part No Description Qty Remarks 1 P Roof Console Screw M 8 x Screw M 8 x Screw M 8 x Disk 8, 4 x Disk 8 x 28mm Disk 8, 4 x 18 DIN NutM Plug Ri D = Plug Ri D = Plug Ri D = Plug Ri D = Label WALTER MAUSER 2-26

29 11 PARTS LIST 11.7 MOUNTING PARTS / No Part No Description Qty Remarks Support Right-hand Support Left-hand Screw M8 x Washer 8,4 x Lock Nut M Support Screw M 12 x 20 DIN Washer 13 x P Silent Bearing SET Silent Bearing Screw M10 x Disk 10, 5 x 22 DIN Thrust Washer D = Nut M16 DIN Nut M10 DIN Screw M16 x

30 11 PARTS LIST 11.8 TARPAULIN COVERING 1/2 6/7 24 3/ /9 21/ No Part No Description Qty Remarks Door Right -hand Door Left-hand Door Frame Right-hand Door Frame Left-hand 1 5 P Buckle SET Hinge above Right-hand Hinge above Left-hand Hinge below Right-hand Hinge below Left-hand Cotter Pin 2.5 x Profile 3.9m Side Window Frame Right-hand Side Window Frame Left-hand 1 23 P mm ( , ) 2.66m SET Profile Covering 1 26 P SET

31 11 PARTS LIST 11.9 ADDITIONAL LIGHTING No Part No Description Qty Remarks 1 W Lighting H - 3 SET Lighting Right-hand H Lighting Left-hand H Lamp H3 12 Volt Relay 12 Volt Cable Rear H Frame Cover Switch Emblem Fuse 10A Grommet D = 13mm Tie Band 145mm 7-29

32 11 PARTS LIST ROTATING LIGHT No Part No Description Qty Remarks 1 W Rotaring Light SET 2 W Console for Rotaring Light SET Rotaring Light Clap Arm Sleeve 5 x 24mm Bracket Screw M6 x Disk 6, 4 x 14 DIN Nut M6 DIN Plate Sleeve Spring Disk 6, 4 x 18 DIN Nut M8 DIN Terminal Nipple M Switch Emblem Cable Base Strap for Cables Socket Outlet 1-30

33 11 PARTS LIST WINDOW SCREEN WASHER No Part No Description Qty Remarks 1 W Window Screen Washer SET Reservoir 2 Ltr + 1 Pump 12 Volt Pump 12 Volt Tie Band 145 mm Hose DI = 4mm, DA = 8mm 4,5 m Nozzle Valve Cable 1-31

34 11 PARTS LIST NOISE REDUCTION KIT No Part No Description Qty Remarks W Anti Noise Equipment SET Barrier (Stipple Sandwich Foam) Barrier (Stipple Sandwich Foam) Barrier (Stipple Sandwich Foam) Clamp Right-hand Clamp Left-hand Barrier (Stipple Sandwich Foam) Barrier (Stipple Sandwich Foam) Bottom Mat Foam Pad Foam Pad 1-32

35 11 PARTS LIST WEIGHT KIT No Part No Description Qty Remarks 1 MBG5455A Weights 2 2 MBG5456A Left-hand Weight Bracket 1 3 MBG5457A Right-hand Weight Bracket Hex Bolt M16 x 90mm Hex Nut M Plain Washer M

36 11 PARTS LIST DECALS

37 11 PARTS LIST DECALS No Part No Description Qty Remarks IDL083 DECAL KIT Cab Control Decal Axel Weight / Serial Decal Decal : Fasten Seat Belt Decal : Instruction Decal : Battery Decal : CE Decal : Noise Decal : Noise Decal : Slope 15 Deg 1-35

38 12 GUARANTEE / SALES & SERVICE GUARANTEE We GUARANTEE that should any defect in workmanship or material occur in the goods within TWELVE MONTHS or to a maximum of one thousand hours from the date of purchase we will repair, or at our option, replace the defective part without making any charge for labour or for materials, provided that the claim under this guarantee is made through an authorised Ransomes' Dealer and that the defective part shall, if we so request, be returned to us or to the Dealer. This guarantee is in addition to, and does not exclude, any condition or warranty implied by law, except that we accept no liability in respect of second-hand goods, or in respect of defects which in our opinion are in any way or to any extent attributable to misuse, lack of reasonable care or ordinary wear and tear, or to the fitting of spares, replacements, or extra components which are not supplied or approved by us for the purpose. The use of non-recommended oil or lubricant nullifies the guarantee. Damage through transport or normal wear does not come under the guarantee. SALES & SERVICE A network of authorised Sales and Service dealers has been established and these details are available from your supplier. When service attention, or spares, are required for the machine, within or after the guarantee period your supplier or any authorised dealer should be contacted. Always quote the registered number of the machine. If any damage is apparent when delivery is made, report the details at once to the supplier of the machine. KEY NUMBERS. It is recommended that all key numbers are noted here: Starter Switch :-... Diesel tank :-... It is also recommended that the machine and engine numbers are recorded. The machine serial number is located on the registration plate and the engine serial number can be found under the exhaust manifold above the starter motor. Machine Number :-... Engine Number :

39 NOTES -37

40 NOTES -38

41

42 World Class Quality, Performance and Support Equipment from Textron Turf Care and Specialty Products is built to exacting standards ensured by ISO 9001 registration at all our manufacturing locations. A worldwide dealer network and factory-trained technicians backed by Textron Parts Xpress provide reliable, high-quality product support. abcdef BOB-CAT BUNTON CUSHMAN JACOBSEN RANSOMES RYAN Ransomes Jacobsen Limited Central Avenue, Ransomes Europark Ipswich, England, IP3 9QG English Company Registration No