Fisherr HP Series Control Valves

Transcription

1 Fisherr HP Series Control Valves HP (Globe Valve) HPA (Angle Valve) Balanced High-Temperature Trim Balanced Tight Shutoff Trim Unbalanced Trim Fisher HP Series control valves are single-port, high-pressure, globe- or angle-stylevalves with metal seats, cage guides, and push-down-to-close valve plug action. These valves are designed for high-pressure applications in process control industries such as power generation, hydrocarbon production, chemical processing, and refining. HP Series valves are designed with corrosion allowance; NACE compliant materials are available. Extra valve body wall thickness provides a safety margin of protection against erosion, as well as extra protection against corrosion due to chemical attack. Because these valves feature a thicker valve body wall, they are available in higher intermediate ratings with weld-end fittings. Unless otherwise noted, all NACE references are to NACE MR and MR003. Balanced High-Temperature Trim HPD and HPAD These valves use a balanced valve plug with graphite piston rings and are well suited for general applications with process temperatures in excess of 232_C(450_F), where extremely tight shutoff is not required. X083- FISHER HP WITH 667 ACTUATOR AND FIELDVUE DVC6200 DIGITAL CONTROLLER Balanced Tight Shutoff Trim HPT and HPAT These valves use a balanced valve plug and offer excellentshutoffwithprocess temperatures below 232_C(450_F). The temperature limits of HPT can be extended above 232_C(450_F) to36_c(600_f) by using PEEK (PolyEtherEtherKetone) anti-extrusion rings in combination with a spring-loaded PTFE seal. The PEEK anti-extrusionringsexpandtohelpcloseoffthe clearance gaps on the plug outside diameter and the cage inside diameter where the PTFE seal may extrude at high temperatures and pressures.

2 Specifications Available Configurations () and Valve Sizes See table Common Characteristics: Designed according to: J ASME B6.34 Valve-Flanges, Threaded and Welding End and J ANSI/ISA End Connections Styles () See table Maximum Inlet Pressure and Temperature (,2) Flanged, Socketwelding, or Buttwelding: Consistent with CL900, 500, and 2500 according to ASME B6.34, unless limited by maximum pressure drop or material temperature capabilities In addition, both steel HP and HPA valves with BWE and SWE connections have increased pressure/temperature ratings as shown in table 3 Maximum Pressure Drop () Valve with Standard Cage: Seefigure2 Valve with Cavitrol III Cage: 49 bar (260 psi) for two-stage and 207 bar (3000 psi) for three-stage cage. Consult Fisher Bulletin 80.2:030, Cavitrol III One-,Two-,andThree-Stage trims, for more information Valve with Whisper Trim III Cage: J 0.6 np/p maximum for levels A and A3 J np/p maximum for levels B and B3 J 0.85 np/p maximum for levels C and C3 J 0.99 np/p maximum for levels D and D3 Valve with WhisperFlo Trim: J Levels X, Y, and Z: 0.94 np/p maximum. If greater than 0.94 np/p, consult your Emerson Process Management sales office Shutoff Classifications See table 4 chrome-moly alloy, J CF8M stainless steel, and J LCC for low temperature service Trim: See table 2 Other Parts: See table 7 Consult your Emerson Process Management sales office for special trim and valve body material availability. Material Temperature Capabilities () HPD,HPAD,HPS,andHPAS:Up to 566_C (050_F) unless limited (see tables 7 or 2 and figure 2) HPT and HPAT: Up to 232_C(450_F) unless limited (see tables 7 or 2 and figure 2) Flow Characteristics (4) StandardCages: J Linear, J equal percentage, J modified equal percentage (5) Cavitrol III and Whisper Trim III Cages: Linear Micro-Flute: Equal percentage Micro-Flat: Linear Micro-Form: J Equal percentage, J modified equal percentage Flow Direction Standard Cage J HPD, HPAD: Normally flow down J HPS, HPAS: Normally flow up (6) J HPAS Micro-Flat: Flow down J HPS, HPAS Micro-Form: Flow up only J HPT, HPAT: Normally flow down Cavitrol III Cage: Flow down Whisper Trim III Cage: Flow up Flow Coefficients See table 2 and also Fisher Catalog 2 Noise Levels See Fisher Catalog 2, Section 3 for noise prediction methods Construction Materials Valve Body and Bonnet: J WCC steel (3), J WC9 Cr-Mo steel (3), J C2A - continued - Port Diameters, Valve Plug Travel, and Stem Diameters Seetables5,8,9,and 2

3 Specifications (continued) Bonnet Style and Mounting () J Standard Bonnet: Seefigure YokeTemperatureLimit: Standard bonnet with cast ironyoke is limited to 537_C (000_F) J Optional Style Extension Bonnet: Used for and 2 valves for CL900 or 500, and valves for CL2500 (see figures 4 and 5) Packing Arrangements J Single, J Double, and J Leakoff standard packing, or optional J ENVIRO-SEAL and J HIGH-SEAL packing systems. See figure 4. Also see bulletin 59.:06, ENVIRO-SEAL and HIGH-SEAL Packing System for Sliding-Stem Valves Yoke Boss Diameter for Actuator Mounting See tables 5 and 0, and figures 3, 4, and 5 Approximate Weight See table 6. The pressure/temperature limits in this bulletin and any applicable standard limitations should not be exceeded. 2. EN (or other valve body material) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office. 3. SA-05 and SA-82-F22 are used for CL2500 HPA valves instead of WCC and WC9. 4. Special characterized cages are available. Contact your Emerson Process Management sales office. 5. Modified equal percentage characteristic is equal percentage for the first 75% of travel, then opens quickly for additional capacity. 6. HPS valves may be used flow down for on-off service only. HPAS valves may be used for flow down in erosive service. 7. For more information contact your Emerson Process Management sales office. 8. Required for all boiler feedwater applications. Options () J Valves with weld-end fittings have increased pressure/temperature ratings, calledintermediate ratings (7), J Class V (6) shutoff for HPT and HPAT to 36_C(600_F) using PEEK anti-extrusion rings (8), J Class V shutoff for HPD and HPAD to 593_C (00_F) using C-seal trim, J expanded ends (7) for 4 and 6 valves ( 4 valves are available with 6 ends, and6valvesareavailablewith8ends),j lubricator or lubricator/isolating valve (7) Table of Contents Balanced High-TemperatureTrim... Balanced Tight Shutoff Trim... Specifications... 2 Unbalanced Trim... 4 Expanded Ends... 4 Cavitrol, Whisper Trim and WhisperFlo Cages... 4 Features... 4 Material Selection Guidelines... 8 Installation... 8 Packing... 0 Trim Selection Guidelines... 8 Trim Material Combinations Pressure/Temperature Limits for Trim Material Combinations Dimensions

4 Figure. Fisher HPD Valve Assembly ( 2 to 6) FLOW Cavitrol III, Whisper Trim III, and WhisperFlo Cages To eliminate cavitation damage in a properly-sized valve, a Cavitrol III cage is available with HPS, HPAS, HPT, and HPAT control valves. To help attenuate aerodynamic noise in gaseous service, Whisper Trim III and WhisperFlo (figure 2) cages are available with HPD, HPAD, HPS, HPAS, HPT, and HPAT control valves. Contact your Emerson Process Management sales office for more information. W585A- Figure 2. Typical WhisperFlo Trim Cut Section View for Fisher Features Valve Plug Stability Rugged cage guiding provides increased valve plug stability, which reduces vibration and mechanical noise. Full Pressure Drop Capability Rugged construction allows full pressure drop capability in HP series valves. W7065 Unbalanced Trim HPS and HPAS These valves have an unbalanced plug and provide excellent shutoff. Expanded Ends Expanded ends are available on the 4 and 6 CL900 and 500 HP valves. The 4 HP valve body is offered with 6 ends. The 6 valve body is offered with 8 ends. Both flanged and buttweld end valve bodies are offered with expanded ends. Spiral-Wound Gaskets for Excellent Sealing Under All Service Conditions Premium materials are used in theconstruction of spiral-wound gaskets for HP Seriesvalves. Thesepremium materials, which make up the standard spiral-woundgaskets, are N06600 (alloy 600)/graphite or N07750 (alloy X750)/graphite. Compliance with the Clean Air Act Optional ENVIRO-SEAL packing systems (figure 4) provide an improved stem seal to help prevent the loss of valuable or emission of hazardous process fluid. The ENVIRO-SEAL packing systems feature PTFE or graphite ULF. Piping Economy The availability of expanded end connections on 4 and 6 HP valves may eliminate the need for line swages while accommodating oversized piping arrangements. Quick Change Trim Maintenance is simple and can easily be performed using common tools. Trim components can be quickly removed and changed with no need for special tools. 4

5 Standard Hard Trim Materials The cage,valve plug, and other trim parts are manufactured from hardened materials. This standard feature provides excellent wear resistance. Control of Low Flow Rates/Tight Shutoff Micro-Flute and Micro-Form valve plugs (figures 6 and 7, respectively) provide superb rangeability in high-pressure, low-flow applications, while maintaining tight shutoff (table 4). A choice of several restricted port diameters helps to match valve body capacity to required flow, to provide necessary control with fulltravel,andtoprevent throttling near the seat. In low-flow applications where cavitation damage may occur, the Micro-Flat valve plug can be used with a special Cavitrol III cage. Contact your Emerson Process Management sales office for more information. Increased Pressure/Temperature Ratings HP Series valves with weld-end fittings have increased pressure/temperature ratings, called intermediate ratings, as defined in ASME B6.34. The extra strength of these valves allows ratings higher than the standard CL900 or 500 ratings specified in B6.34. Contact your Emerson Process Management sales office for further information on intermediate ratings. Trim Interchangeability Cavitrol III, Whisper Trim III, and WhisperFlo trims (figures 8, 9, and 0) are interchangeable with standard trims. Smooth Control at High Pressure Drops Available on 2 through 6 valves, balanced trim provides smooth control at high pressure drops. High-Temperature Capability with Class V Shutoff Use of C-seal trim (see figure 5) permits Class V shutoff up to 593_C (00_F) for HPD valves. Sour Service Trims Available Long-lasting, erosionand corrosion-resistant trims are available for control of sour service. These trims are offered with either a standard cage, a Cavitrol III cage, a Whisper Trim III cage, or WhisperFlo trim. Spiral-wound gasket construction is standard. 5

6 Table. Available Constructions DESIGN SIZE, PRESSURE RATING BODY MATERIAL AND END CONNECTION STYLE (, 2) WCC, WC9, LCC, C2A, and CF8M (36 Stainless Steel) Cast Valves RF or RTJ Flanged, Butt Weld, and Socket Weld (3) SA-05, SA-82-F22, and SA-82-F36forged SST (for forged steel HPA CL2500 angle valves) Socket Weld HPAD 2to8 CL900 and 500 X CL X HPAS to2 CL900 and 500 X --- CL X HPAT 2to8 CL900 and 500 X CL X HPD 2to6 CL900 and 500 X CL2500 X --- HPS to3 CL900 and 500 X --- to2 CL2500 X --- HPT 2to6 CL900 and 500 X CL2500 X --- X = Available Construction.. End connection style abbreviations: RF - Raised Face, RTJ - Ring Type Joint. 2. EN (or other valve body material) ratings and end connections can usually be supplied; consult your Emerson Process Management sales office. 3. Socket Weld available on, -/2, and 2 only. Table 2. Typical Flow Coefficients () Valve Size, HP CL500 Valve Style Characteristic Maximum Cv Modified Equal Percentage 7. 2 HP CL500 Linear HP CL500 Linear 2 4 HP CL500 Linear 20 6 HP CL500 Linear 425 HPA CL500 Modified Equal Percentage HPA CL500 Linear 64.3 HPA CL2500 Modified Equal Percentage HPA CL2500 Linear See the section titled Coefficients in this bulletin and also Catalog 2 for a complete listing of flow coefficients. Table 3. Increased Pressure/Temperature Ratings for Steel Valves with BWE and SWE Connections () Valve Type Globe Valves Valve Size, Intermediate Rating Pressure Rating (ASME B6.34) CL900 and CL CL900 and CL CL CL Contact your Emerson Process Management sales office for further information on intermediate ratings. 6

7 Table 4. Shutoff Classifications per ANSI/FCI 70-2 and IEC HPD, HPAD w/ C-seal trim Valve Design Port Diameter, mm (Inches) ANSI/FCIandIEC Leakage Class HPD, HPAD Valve Size, HPD HPAD 47.6 (.875) II 58.7 (2.325) to 92. (3.625). (4.375) and larger II - Standard III - Optional III - Standard IV - Optional Port Diameter, mm (Inches) Cage Style ANSI/FCIandIECLeakageClass (2.875) HPS, HPAS, HPT, HPAT HPS and HPT w/ TSO (Tight Shutoff trim) HPT and HPAT w/ PEEK () Anti-Extrusion Rings Eq.%,Mod.Eq.%, Linear (std. cage), Linear (Whisper III, A, B) 73 (2.875) Linear (Whisper III, D3) Eq.%,Mod.Eq.%, 92. (3.625) Linear (std. cage), Linear (Whisper III, A, B3, C3). (4.375) Linear (Whisper III, D3) 36.5 (5.375). PEEK (PolyEtherEtherKetone), required for all boiler feedwater applications. All Eq.%,Mod.Eq.%, Linear (std. cage), Linear (Whisper III, A, B3, C3) Cavitrol III and Micro-Flat Micro-Form, Micro-Flute, Eq. %, Mod Eq. %, Linear, Whisper III See table 5 See table (.875) to 36.5 (5.375) All V - Standard to 593_C (00_F) (for port diameters from 73 mm [2.875 inch] through 36.5 mm [5.375 inch] with optional C-seal trim) IV - Optional (for port diameters 73 mm [2.875 inch] through 36.5 mm [5.375 inch] V - Standard IV - Standard V - Optional TSO - Optional TSO is not an ANSI/FCI or IEC leakage class. Valves with TSO trim are factory tested to a more stringent Fisher test requirement of no leakage at time of shipment. Test medium is water. Specify service Pwhenordering. Test procedure is ANSI/FCI Class V test procedure B V - Standard (to 36_C [600_F]) IV - Optional (47.6 mm [.875 inch] through 36.5 mm [5.375 inch] ports) 7

8 Material Selection Guidelines Usethefollowingstepsasaguidelinefortheselection of materials:. Determine the pressure/temperature rating of the valve body size and material required. Inlet pressure and temperature must always be limited by the applicable ASME pressure/temperature rating. 2. SelectthedesiredtrimstylefromtheAvailable Configurations specification and from table 4, Shutoff Classifications. 3. Select desired materials from tables 7, 8,, and 2 and figure 2. The temperature capabilities determined from figure 2 may be further limited by the temperature capabilities of materials selected from tables 7 and 2. Refer to figure 2 to determine pressure drop limits of the valve body-trim combinations selected. Installation The valve must be installed so flow through the valve is as indicated by the flow direction arrow on the valve body. Consideration should be given to installing an upstream strainer, especially if the valve uses a Cavitrol III cage, Whisper Trim III, or WhisperFlo trim. Overall dimensions are shown in figures 3, 4, and 5. Face-to-face dimensions are in compliance with ANSI/ISA Actual end connection dimensions conform to ASME B6.25 for buttwelding ends and to ASME B6.5 for flanged ends. 8

9 Table 5. Port Diameters, Valve Plug Travel, Yoke Boss Diameters for TSO (Tight Shutoff) Trim TYPE TRIM MAX TRAVEL YOKE BOSS SIZE Nominal PORT DIAMETER Actual TSO C V REDUCTION AT 00% TRAVEL () UNBALANCE AREA mm Inch mm Inch mm Inch mm Inch Inch 2 Balanced Plugs Flow Down Only HPT 3 (2) CAV III 3-Stage / % 0.03 HPT 4 HPT 6 HPS 2 CAV III 3-Stage CAV III 3-Stage 02 4 Standard / / /6 5 Unbalanced Plugs Flow Down Only % % % CAV III 3-Stage / % This column lists the percent reduction of published maximum C V of the trim listed in the TRIM column. 2. Not available with 5-inch yoke boss. Figure 3. Typical Balanced TSO Trim PLUG SEAL W7020- TSO PROTECTED SOFT SEAT SEAL 9

10 Figure 4. ENVIRO-SEAL and HIGH-SEAL Packing Systems PACKING BOX STUD PACKING BOX STUD SPRING SPRINGS PACKING FOLLOWER PACKING FOLLOWER W8533- TYPICALHIGH-SEAL PACKING SYSTEM WITH GRAPHITE ULF PACKING W8532- TYPICAL ENVIRO-SEAL PACKINGSYSTEM WITH GRAPHITE ULF PACKING PACKING BOX STUDS SPRINGS ANTI- EXTRUSION RING PACKING RING LANTERN RING BONNET W TYPICAL ENVIRO-SEAL PACKINGSYSTEM WITH PTFE PACKING 0

11 Table6. ApproximateWeights (Valve and Bonnet Assemblies) TYPE Globe Valves Angle Valves. Only SWE is available for CL2500. Figure 5. C-seal Trim SIZE, PRESSURE RATING KILOGRAMS POUNDS Flg SWE, BWE Flg SWE, BWE CL900 and CL /2 x 2 CL CL900 and CL CL CL CL CL CL CL CL900 and CL () () CL900 and CL () () 3 CL CL CL CL C-SEAL METAL PLUG SEAL () C-SEAL METAL PLUG SEAL () FLOW DOWN FLOW UP VIEW A 37B399-A Note:. Reverse the orientation of the C-seal plug seal for proper shutoff when valve is used in a process with different fluid flow direction.

12 Table 7. Construction Materials and Temperature Capabilities for Parts Other than Valve Body and Trim TEMPERATURE CAPABILITIES PART MATERIAL _C _F Valve plug stem S to to 00 HPD piston ring Graphite (FMS 7F27) Graphite (FMS 7F39) -254 to 427 (to 482 for nonoxidizing service) -254 to 537 (to 593 for nonoxidizing service) -425 to 800 (to 900 for nonoxidizing service) -425 to 000 (to 00 for nonoxidizing service) Backup ring S4600 (46 SST) -29 to to 800 S3600 (36 SST) -98 to to 00 Spring-loaded S30200 (302 SST) Retaining ring HPT or HPAT N07750 (NACE) -254 to to 00 valve plug seal Seal ring PTFE with N0276 Spring -73 to 232 (5) -00 to 450 (5) Anti-extrusion rings PEEK (PolyEtherEtherKetone) -73 to to 600 Cage gasket N06600/Graphite -240 to to 00 TSOprotected softseatseal Carbon-filled PTFE -73 to to 450 Seat ring gasket N06600/Graphite -240 to to 00 Valve Body-tobonnet bolting () Packing Studs Nuts Studs Nuts Studs Nuts Studs Nuts Studs Nuts Studs Nuts Steel SA93-B7 (all valve body materials) Steel SA94-2H (allvalvebodymaterials) Steel SA93-B7Mfor sourservice Steel SA94-2HMfor sour service Steel SA93-B6 (WC9 and C2Avalvebody mat'ls) Steel SA94-7 N0778 SST (SB637) (3) Steel SA to 427 (WCC and WC9) -46 to 37 (LCC) -48 to 427 (36 CF8M) (2) -29 to 427 (WCC) -46 to 37 (LCC) -20 to 800 (WCC and WC9) -50 to 700 (LCC) -55 to 800 (36 CF8M) (2) -20 to 800 (WCC) -50 to 700 (LCC) -29 to to to 566 (WC9) -29 to 593 (C2A) -20 to 050 (WC9) -20 to 00 (C2A) S3600 stainless steel SA93-B8M (strain hardened) (CF8M valve body mat'ls) (4) S3600 stainless steel SA94-8M (CF8M valve body mat'ls) (4) -98 to to 800 S2090 SST (SA479-XM-9) (3) (CF8M valve body mat'ls) Steel SA to to 00 PTFE V-ring -46 to to 450 Graphite ribbon filament (oxidizing service to 37_C [700_F]) -254 to to 000 Graphite ribbon (high-temperature oxidizing service) 37 to to 00 Packing follower, spring, or lantern ring S3600 stainless steel -254 to to 00 Packing box ring S3600 stainless steel -254 to to 00 Packing flange, studs, or nuts Steel -29 to to 800 S3600 stainless steel -98 to to 00. Valve body materials with which these bolting materials may be used are shown in parentheses. 2. Steel studs and nuts with NCF (non-corrodingfinish)coatingareusedwith4and6cf8mvalvebodies. 3. These stud materials are not listed in ASME B For valve sizes up through If used with PEEK anti-extrusion rings, PTFE/carbon seal ring may beused in temperatures up to 36_C (600_F)for non-oxidizing serviceor up to 260_C (500_F)for oxidizing service. 2

13 Table 8. Additional Globe Valve Specifications SIZE, 2 3 FLOW CHARACTERISTIC Equal percentage Modified equal percentage Cavitrol III, 2-stage) Equal percentage Std) Whisper Trim III, level A) Modified equal percentage Cavitrol III, 2-stage) Cavitrol III, 3-stage) Modified equal percentage Std) Whisper Trim III, level A, B) Cavitrol III, 2-stage) Cavitrol III, 3-stage) BODY DESIGN AND PLUG STYLE HPS w/micro-flute HPS w/micro-form HPS w/micro-form PORT DIAMETER PLUG TRAVEL STEM DIAMETER mm Inches mm Inches mm Inches , , , 9. /2 /2 /2 /2 /2 /2, 3/4 /2,3/4 /2, 3/4 HPS , 9. /2, 3/4 HPS w/micro-form , 9. /2 /2 /2, 3/4 HPS , 9., () /2, 3/4, () HPS, HPD, HPT , 9., () /2, 3/4, () HPS w/micro-form ,9., 2.7, 9., 2.7, 9., /2, 3/4, /2, 3/4, /2, 3/4, HPS, HPD, HPT , 9., () /2, 3/4, () HPT , 9. /2, 3/4 HPS /4 HPD, HPT ,9., /2, 3/4, HPT , 9., /2, 3/4, HPT , 9., /2, 3/4, -continued- 3

14 Table 8. Additional Globe Valve Specifications (Continued) SIZE, 4 6 FLOW CHARACTERISTIC BODY DESIGN AND PLUG STYLE PORT DIAMETER PLUG TRAVEL STEM DIAMETER mm Inches mm Inches mm Inches Modified equal percentage (Std) Whisper Trim III level A, A3, B3, C3) Whisper Trim III level HPD, HPT HPD, HPT , 9., 3/4, 3/4, D3) Cavitrol III, 2-stage) HPT , 3/4, Cavitrol III, 3-stage) HPT , 3/4, Modified equal percentage (2) Std) HPD, HPT ,, 3.8 3/4,, -/4 Whisper Trim III, level A, B3, C3) HPD, HPT , 3.8,-/4 Whisper Trim III, level D3) HPD, HPT , 3.8,-/4 Cavitrol III, 2-stage) HPD, HPT ,, 3.8 3/4,,-/4 Cavitrol III, 3-stage) HPD, HPT ,5.4, 3.8 3/4,,-/4. Available only with HPS valve. 2. The first 75% is equal percentage. 4

15 Table 9. Valve Stem Travels for CL2500 Globe Valves SIZE, DESIGN / PLUG STYLE HPS / Micro-Formor Micro-Flute 2 HPS / Micro-Form HPS / Micro-Form HPS HPD, HPT CHARACTERISTIC Equal Percentage Modified Equal Percentage Equal Percentage Modified Equal Percentage PORT DIAMETER MAXIMUM STEM TRAVEL mm Inches mm Inches 6.4, 9.5, 2.7, 9., 6.4, 9.5, 2.7, 9., 6.4, 9.,, , 9.,, , 0.375, 0.5,, 0.25, 0.375, 0.5,, 0.25,,, ,,, Equal Percentage Modified Equal Percentage Linear Equal Percentage Modified Equal Percentage Linear Equal Percentage Modified Equal Percentage Table 0. Globe and Angle Valve Yoke Boss and Valve Stem Diameter Combinations () SIZE, STANDARD DIAMETERS OPTIONAL DIAMETERS mm Inches mm Inches Stem Yoke Boss Stem Yoke Boss Stem Yoke Boss Stem YokeBoss / / /6 3-9/ / / (2) Seetables8,9,andforvalvestemdiameters available for specific constructions. 2. Angle valve construction only (HPAD, HPAT) / / /6 5

16 Table. Additional Angle Valve Specifications SIZE, 2 FLOW CHARACTERISTIC Equal percentage Modified equal percentage Linear (cage style: Std) Cavitrol III, 2-stage) Equal percentage Modified equal percentage Linear (cage style: std) Linear (cage style: std) Whisper III, level A) Cavitrol III, 2-stage) Cavitrol III, 3-stage) BODY DESIGN AND PLUG STYLE FLOW DIRECTION HPAS w/micro-flute Up (2) HPAS w/micro-form Up HPAS, equal percentage characterized cage 2.7 HPAS w/micro-form Up 9. PORT DIAMETER PLUG TRAVEL STEM DIAMETER mm Inches mm Inches mm Inches , 9. /2 /2 /2 /2 /2 /2, 3/4 Down / , , 9. /2 /2, 3/4 /2, 3/4 HPAS Down /4 HPAS w/ Micro-Flat Down HPAS, HPAD Down ,9. /2,3/4 HPAS w/micro-flute Up (2) HPAS w/micro-form Up HPAS, equal percentage characterized cage Down , , 9., /2 /2 3/4 /2 /2 /2 /2 /2 /2, 3/4 /2, 3/4, 3/4 3/4 HPAS Up , 9., /2, 3/4, HPAT, HPAD Down , 9. /2, 3/4 HPAS w/micro-form HPAS, equal percentage characterized cage Up Down , 9., 2.7, 9., 2.7, 9., /2, 3/4, /2, 3/4, /2, 3/4, 3/4 3/4 HPAS Up , 9., /2, 3/4, HPAT, HPAD Down , 9. /2, 3/4 HPAS w/micro-flat Down /4 HPAS Up , 9., /2, 3/4, HPAT, HPAD Down , 9. /2, 3/4 HPAS, HPAT, HPAD Up , 9., () /2, 3/4, () HPAT Down , 9. /2, 3/4 HPAS Down /4 -continued- 6

17 Table. Additional Angle Valve Specifications (continued) SIZE, FLOW CHARACTERISTIC Equal percentage Modified equal percentage Std) Whisper III, level A) Cavitrol III, 2-stage) Cavitrol III, 3-stage) Equal percentage Modified equal percentage Std) Whisper III, level A, B) Cavitrol III, 2-stage) Cavitrol III, 3-stage) Equal percentage Modified equal percentage Std) Whisper III, level A, A3, B3, C3) Whisper III, level D3) Cavitrol III, 2-stage) Cavitrol III, 3-stage) Equal percentage Modified equal percentage Std) Whisper III, level A, A3, B3, C3) Whisper III, level D3) Cavitrol III, 2-stage) Cavitrol III, 3-stage) HPAT, HPAD BODY DESIGN AND PLUG STYLE FLOW DIRECTION PORT DIAMETER PLUG TRAVEL STEM DIAMETER mm Inches mm Inches mm Inches Down , 9. /2, 3/4 Down , 9. /2, 3/4 Down Up , 9. /2, 3/4 HPAT Down , 9. /2, 3/4 HPAS Down /4 HPAT, HPAD HPAT HPAT, HPAD HPAT HPAT, HPAD HPAT Down , 9., /2, 3/4, Down Down Up , 9., /2, 3/4, Down , 9., /2, 3/4, Down , 9., /2, 3/4, Down , 3/4, Down Down Up , 3/4, Up , 3/4, Down , 3/4, Down , 3/4, Down ,, 3.8 3/4,, -/4 Down Down. Available only with HPAS valves. 2. Micro-Flutes ( flute and 0.5 inch port 2 flute) may be used flow down in flashing and erosive service ,, 3.8 3/4,, -/4 Up , 3.8, -/4 Up , 3.8, -/4 Down ,, 3.8 3/4,, -/4 Down ,, 3.8 3/4,, -/4 7

18 Figure 6. Fisher HPS Trim with Micro-Flute Valve Plug Figure 7. Fisher HPS Trim with Micro-Form Valve Plug W586- FLOW W587- FLOW Trim Selection Guidelines Refer to the following descriptions as a guideline for the selection of appropriate trims. Trim 20A Trim 20A is the standard trim for carbon steel and alloy steel valve body materials. This trim is recommended for general or severe service applications up to 343_C(650_F) or 427_C (800_F) depending on valve construction. Typical applications for this trim include services in boiler feedwater, water, non sour hydrocarbons, and steam. Trims 202 and 202H Trims 202 and 202H are designed for use in high temperature applications up to 566_C (050_F). Trim 202H includes special tolerances required for larger sized HPD and HPAD constructions, as indicated in table 2, at operating temperatures above 343_C (650_F). Trim 203 Trim 203 is the standard trim for stainless steel valvebodymaterials and should only be used with stainless steel valve body materials. This trim meets the metallurgical requirements of NACE MR and can be used in applications up to 593_C (00_F) Trim 204 Trim 204 is used in sour or moderately corrosive services. This trim meets the metallurgical requirements of NACE MR and canbe used with carbon steel and alloy steel valve body materials. Trim 20 Provides a S3600 CoCr-A hardfaced valve plug, which can be easily weld repaired. The S7400 H075 cage in this trim also allows it to be usedinanhptorhpatconstruction. Trim 2 Trim 2 is the standard trim for C2A valve body materials and should only be used with C2A valve body materials. C2A should only be used when the pressure and temperature capabilities for WC9 valve body materials are not acceptable. 8

19 Figure 8. 2 Fisher HPSTrim withcavitroliii 3-Stage Cage Figure 0. Fisher HPD Trim with Whisper Trim III Level D Cage (also available in HPT and HPS) W588- FLOW W595- FLOW Figure 9. Fisher HPT Trim with Whisper Trim III Level A Cage (also available in HPD [ 2-6] and HPS [ 2 and 3]) Figure. Fisher HPAS Trim with Micro-Flat Valve Plug W602- W5952- FLOW FLOW C-seal Trim Description C-seal trim is available for HPD and HPAD valves with port diameters from 2.875inches through inches. With C-seal trim, a balanced valve can achieve high-temperature, Class V shutoff. Because the C-seal plug seal is formed from metal (N0778 nickel alloy) rather than an elastomer, a valve equipped with the C-seal trim can be applied in processes with a fluid temperature of up to 593_C (00_F). Fisher TSO (Tight Shutoff) Trim Capabilities TSO trim is available for HPS and HPT valves with port diameters as defined in table 5. Also see figure 3 and table 4. TSO trim consists of a protected soft seat plus PEEK anti-extrusion rings with a spring-loaded PTFE plug seal. Used only in flow down applications, TSO trim offers unparalleled shutoff integrity, resulting in longer plug and seat life. For additional information contact your Emerson Process Management sales office. 9

20 Table 2. Trim Material Combinations TRIM USAGE PLUG CAGE SEATRING 20A H (4) 203 (NACE )(5) 204 (NACE) (5) 20 2 HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 &500 & -2 HPD & HPS only ( -6 CL900 & 500 & to 2 HPAD & HPAS only ( -8 CL900 & 500 & -2 HPD 6 CL900 & 500, HPAD 8 CL900 & 500 only HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 & 500 & -2 HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 & 500 & -2 HPD & HPS only ( -6 CL900 & 500 & to 2 HPAD & HPAS only ( -8 CL900 & 500 & -2 S4600 heat-treated for HP, HPA, Micro-Form (HPA), and flow down HPAS) or S44004 (440C SST) heat-treated for Micro-Flute and Micro-Flat (HPA only) valve plugs S3600 (36 stainless steel) with CoCr-A seat and guide S3600 (36 stainless steel) with CoCr-A seat and guide S3600 with CoCr-A seat and guide S3600 with CoCr-A seat and guide S3600 with CoCr-A seat and guide F9withCoCr-A seat and guide With Standard Cage S7400 (7-4SST) H075 heat-treated F22 Cr-Mo alloy steel nitrided F22 Cr-Mo alloy steel nitrided S3600/hard Cr coat S7400 Double H50 heat-treated S7400 H075 S4600 heat-treated or HPA (S44004 heat-treated seat ring for Micro-Flat S44004 heat-treated seat and liner) S3600/CoCr-A or R30006 (Alloy 6) for Micro-Flat valve plugs R30006 seat, liner (3) S3600/CoCr-A S3600/CoCr-A or R30006 (Alloy 6) for Micro-Flat valve plugs R30006 seat, liner (3) S3600/CoCr-A or R30006 (Alloy 6) for Micro-Flat valve plugs R30006 seat, liner (3) S3600/CoCr-A BODY MATERIAL () OPERATING TEMPERATURE RANGE (2) _C _F WCC -29 to 343 (8) -20 to 650 (8) LCC -29 to to 650 WC9-29 to 343 (8) -20 to 650 (8) WCC -29 to to 800 LCC -46 to to 650 WC9-29 to to 050 WCC 260 to to 800 LCC 260 to to 650 WC9 260 to to 050 CF8M -98 to 593 (2) -325 to 00 (2) WCC -29 to to 800 LCC -46 to to 650 WC9-29 to to 050 WCC -29 to to 800 LCC -46 to to 650 WC9-29 to to 050 F9 ion nitrided F9 with CoCr-A C2A -29 to to 00 -continued- 20

21 Table 2. Trim Material Combinations (continued) TRIM USAGE PLUG CAGE SEATRING 205A 205B (6) 206 (NACE) (5) 207A 207B H (4) 209 (NACE) (5) 22 HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 & 500 & -2 HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 & 500 & -2 HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 & 500 & -2 HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 & 500 & -2 HP ( -6 CL900 & 500 & -2 CL2500 HPD & HPS only ( -6 CL900 & 500 & to 2 HPAD&HPAS(-8 CL900 & 500 & -2 HPD ( 6 CL900 & 500) HPAD ( 8 CL900 & 500 only) HP ( -6 CL900 & 500 & -2 HPA ( -8 CL900 & 500 & -2 HPD & HPS only ( -6 CL900 & 500 & to 2 HPAD & HPAS only ( -8 CL900 & 500 & -2 S44004 heat-treated S44004 heat-treated S3600 with CoCr-A seat and guide S4600 heat-treated S4600 heat-treated S3600 with CoCr-A seat and guide S3600 with CoCr-A seat and guide S3600 with CoCr-A seat and guide F9withCoCr-A seat and guide With Cavitrol III Cage S7400 H075 heat-treated S7400 H075 heat-treated S7400 Double H50 heat-treated S44004 S44004 S3600/CoCr-A With Whisper Trim III Cage S7400 H075 heat-treated S7400 H075 heat-treated F22 steel nitrided F22 steel nitrided S7400 Double H50 heat-treated S4600 heat-treated S3600/CoCr-A S3600/CoCr-A S3600/CoCr-A S3600/CoCr-A BODY MATERIAL () WCC LCC WC9 WCC LCC WC9 OPERATING TEMPERATURE RANGE (2) _C _F -29 to 232 (7) -20 to 450 (7) -29 to 232 (7) -20 to 450 (7) WCC -29 to 232 (7) -20 to 450 (7) LCC -46 to 232 (7) -50 to 450 (7) WC9-29 to 232 (7) -20 to 450 (7) WCC LCC WC9-29 to 343 (8) -20 to 650 (8) WCC -29 to to 800 LCC -29 to to 650 WC9-29 to to 800 WCC -29 to to 800 LCC -46 to to 650 WC9-29 to to 050 WCC -29 to to 800 LCC -46 to to 650 WC9-29 to to 050 WCC -29 to to 650 LCC -46 to to 650 WC9-29 to to 650 F9 ion nitrided F9 with CoCr-A C2A -29 to to 00. If using valve body/trim combinations other than those listed, consult your Emerson Process Management sales office. 2. Temperatures above 538_C (000_F) require a non-standard CF8M body material (CF8M to FMS 20B6). 3. For HPA valves. 4. Trims 202H and 208H have valve plug tolerances for high temperature service and are used in place of trims 202 and 208 for the constructions listed when operating temperatures exceed 343_C (650_F). 5. NACE MR Trim 205B has a S3600 valve stem instead of the standard S2090 material stage and 2 3 stage HPS can be used at temperatures up to 343_C(650_F). 8.and2canbeusedattemperaturesupto427_C(800_F). 2

22 Table3.FlowingPressureDropLimitsfor6HPDandHPT Valves (Without Cavitrol III or Whisper Trim III Cage) MAXIMUM FLOWING STEM FLOW PRESSURE DROP DIAMETER, MEDIA Bar PSI mm (INCHES) Flow Down Flow Up Flow Down Flow Up 9 (3/4) All except () boiler 3.8 (-/4) feedwater 5.8 x 3.8 () (2 x -/4) (-/4) Boiler 5.8 x 3.8 feedwater (2 x -/4).Requires 3.8 mm (-/4 inch)s2090 stem with 52.8 mm (2-inch) plug-to-stem connection. Figure2. Pressure-Temperature Limits for Trim Material Combinations -29 FLUID TEMPERATURE, -29 _C FLUID TEMPERATURE, _C PRESSURE DROP, PSI , FLUID TEMPERATURE, _F PRESSURE DROP, BAR, DIFFERENTIAL PRESSURE DROP, PSI , H, 208H FLUID TEMPERATURE, _F PRESSURE DROP, BAR, DIFFERENTIAL 3-40 FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C FLUID TEMPERATURE, _C PRESSURE DROP, PSI FLUID TEMPERATURE, _F FLUID TEMPERATURE, _F SOUR SERVICE APPLICATIONS (NACE) 2 Notes: 2 3 Use trim 207B in 3, 4, 6 HP and 4, 6, 8 HPA above 343_C (650_F). NACE MR Be especially careful to specify service temperature if trim 202 or 208 is selected, As different thermal expansion rates require special plug clearances. 4 The limit for 2-stage and 2 valves is 260 psig. For 3 to 6 valves the limit is 800 psig. C , PRESSURE DROP, BAR, DIFFERENTIAL PRESSURE DROP, PSI LIMIT FOR 3-STAGE LIMIT FOR 2-STAGE PRESSURE DROP, BAR, DIFFERENTIAL PRESSURE DROP, PSI FLUID TEMPERATURE, _F PRESSURE DROP, BAR, DIFFERENTIAL 22

23 Table 4. Globe Valve Dimensions with Standard Bonnet A () ASME EN SIZE, CL900 CL500 RF RTJ BWE SWE RF RTJ PN60 PN250 mm CL CL900 CL500 PN60 PN250 Inches CL RF-raised-face flanges; RTJ-ring-type jointflanges;bwe-buttweldingends; SWE-socketweld ends. Table 5. Globe Valve Dimensions with Standard Bonnet B () ASME EN SIZE, CL900 CL500 PN60 PN250 RF RTJ BWE SWE RF RTJ mm (2) (3) CL CL900 CL500 PN60 PN250 Inches (2) (3) CL RF-raised-face flanges; RTJ-ring-type jointflanges;bwe-buttweldingends; SWE-socketweld ends. 2. Manufactured in U.S.A. 3. Manufactured in Europe and Japan. Table 6. Globe Valve Dimensions with Standard Bonnet STANDARD BONNETS D Yoke Boss Diameters, mm (Inches) SIZE, G 27 7 (2-3/6) 90 (3-9/6) (5) mm CL900 and Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage () (2) CL Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage Inches CL900 and Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage () (2) CL Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage EXTENSION BONNETS (CL900 AND 500) D Yoke Boss Diameters, mm (Inches) SIZE, G 27 7 (2-3/6) 90 (3-9/6) (5) mm Std, Whisper III, Cavitrol III 3-Stage Inches Std, Whisper III, Cavitrol III 3-Stage 2, Cavitrol III 2-Stage , Cavitrol III 2-Stage Manufactured in U.S.A. 2. Manufactured in Europe and Japan. 23

24 Figure 3. Globe Valve Dimensions with Standard Bonnet (also see tables 4, 5, and 6) MATCH LINE FOR ACTUATOR MATCH LINE FOR ACTUATOR MATCH LINE FOR 585C SERIES ACTUATORS AND TYPE 657, 667 SIZE 00 ACTUATORS MATCH LINE FOR ALL OTHER ACTUATORS (.00) mm (INCHES) A5700A-3 FLANGED WITH 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS BUTTWELDING END WITH 7 OR 90 mm (2-3/6 OR3-9/6 INCH) DIAMETER YOKE BOSS TYPICAL, 2, AND 3 27mm (5-INCH) DIAMETER YOKE BOSS FOR USE WITH ALL S MATCH LINE FOR ACTUATOR MATCH LINE FOR ACTUATOR MATCH LINE FOR 585C SERIES ACTUATORS AND TYPE 657, 667 SIZE 00 ACTUATORS MATCH LINE FOR ALL OTHER ACTUATORS (.00) FLANGED WITH 7 OR 90 mm (2-3/6 OR3-9/6 INCH) DIAMETER YOKE BOSS A279A-4 BUTTWELDING END WITH 7 OR 90 mm (2-3/6 OR3-9/6 INCH) DIAMETER YOKE BOSS TYPICAL 3 (EUROPE AND JAPAN MANUFACTURE), 4, AND 6 27mm (5-INCH) DIAMETER YOKE BOSS FOR USE WITH FLANGED OR BUTTWELDING mm (INCHES) Note: For dimensions of valves with other end connections, consult your Emerson Process Management sales office. 24

25 Table 7. Dimensions D for Style Extension Bonnet (A, B, and G Dimensions Listed in Figure 3 Do Not Change When Extension Bonnet is Used) D SIZE, Yoke Boss Diameters, mm (Inches) 7 (2-3/6) 90 (3-9/6) 27 (5) mm (stdtrim) (std, Whisper III, Cavitrol III, 3-stagetrim) (CavitrolIII 2-stage trim) Inches (stdtrim) (std, Whisper III, Cavitrol III 3-stage trim) (CavitrolIII 2-stage trim) Figure 4. Dimensions D for Style Extension Bonnet (A, B, and G Dimensions Listed in Figure 3 Do Not Change When Extension Bonnet is Used) (also see table 7) MATCH LINE FOR ACTUATOR MATCH LINE FOR 585C SERIES ACTUATORS MATCH LINE FOR ALL OTHER ACTUATORS D (.00) 27 mm (5-INCH) DIAMETER YOKE BOSS FOR STYLE EXTENSION BONNET D G B A FLANGED WITH STYLE EXTENSION BONNET HAVING 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS A570A-2 mm (INCHES) 25

26 Table 8. Angle Valve Dimensions with Standard Bonnet STANDARD BONNETS D Yoke Boss Diameters, mm (Inches) SIZE, 7 (2-3/6) 90 (3-9/6) 27 (5) CL900 and 500 CL2500 CL900 and 500 CL2500 CL900 and 500 CL2500 mm Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage Inches Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage EXTENSION BONNETS D Yoke Boss Diameters, mm (Inches) SIZE, 7 (2-3/6) 90 (3-9/6) 27 (5) CL900 and 500 CL2500 CL900 and 500 CL2500 CL900 and 500 CL2500 mm Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage Inches Std, Whisper III, Cavitrol III 3-Stage 2 Cavitrol III 2-Stage

27 Table 9. Angle Valve Dimensions with Standard Bonnet SIZE, G A&G () ASME CL2500 CL900 CL500 SWE SWE RF RTJ BWE SWE RF RTJ mm Inches RF raised-face flanges; RTJ ring-type-jointflanges;bwe buttwelding ends;swe socket-weld ends. PN60 EN PN250 Figure 5. Angle Valve Dimensions with Standard Bonnet (also see tables 8 and 9) MATCH LINE FOR ACTUATOR MATCH LINE FOR ACTUATOR A608A- FLANGED WITH 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS FLANGED WITH STYLE EXTENSION BONNET HAVING 7 OR 90 mm (2-3/6 OR 3-9/6 INCH) DIAMETER YOKE BOSS For CL900 and 500 valves, G = A. For CL2500 valves, see table 9 for the G dimension. Note: For dimensions of valves with other end connections, consult your Emerson Process Management sales office. 27

28 Neither Emerson, Emerson Process Management, nor any of their affiliated entities assumes responsibility for the selection, use or maintenance of any product. Responsibility for proper selection, use, and maintenance of any product remains solely with the purchaser and end user. Fisher, FIELDVUE, WhisperFlo, Cavitrol, Whisper Trim, and ENVIRO-SEAL are marks owned by one of the companies in the Emerson Process Management business unit of Emerson Electric Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the property of their respective owners. The contents of this publication are presented for informational purposes only, and while every effort has been made to ensure their accuracy, they are not to be construed as warranties or guarantees, express or implied, regarding the products or services described herein or their use or applicability. All sales are governed by our terms and conditions, which are available upon request. We reserve the right to modify or improve the designs or specifications of such products at any time without notice. Emerson Process Management Marshalltown, Iowa 5058 USA Sorocaba, 8087 Brazil Chatham, Kent ME4 4QZ UK Dubai, United Arab Emirates Singapore 2846 Singapore E2899, 203 Fisher Controls International LLC. All rights reserved.