Clutch Master Cylinder Replacement
|
|
- David Williamson
- 5 years ago
- Views:
Transcription
1 1 of 6 3/23/2018, 3:56 PM 2002 Chevrolet Camaro Camaro, Firebird VIN F Service Manual Transmission/Transaxle Clutch Repair Instructions Clutch Master Cylinder Replacement Tools Required J Hydraulic Clutch Line Separator Removal Procedure 1. Remove the driver side instrument panel insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side in Instrument Panel, Gauges and Console. 2. Remove the drive side knee bolster. Refer to Driver Knee Bolster Replacement in Instrument Panel, Gauges and Console.
2 2 of 6 3/23/2018, 3:56 PM 3. Remove the clutch pedal pin retainer (1). 4. Remove the clutch master cylinder push rod (3) from the clutch pedal pin (2). 5. Remove the clutch master cylinder nuts (7). 6. Remove the clutch master cylinder push on nuts (6). 7. Remove the clutch master cylinder U-bolt (4). 8. Remove the clutch master cylinder (5) from the front of dash. 9. Raise and suitably support the vehicle. Refer to Lifting and Jacking the Vehicle in General Information. 10. Using the J 36221, depress the white circular release ring on the actuator hose and simultaneously pull lightly on the master cylinder hose to disconnect. 11. Protect both hose coupling ends from dirt and damage. 12. Lower the vehicle.
3 3 of 6 3/23/2018, 3:56 PM 13. Remove the clutch master cylinder reservoir push-in retainer. 14. Slide the clutch master cylinder reservoir out from the hood strut bracket. 15. Remove the clutch master cylinder (and reservoir) from the vehicle. Installation Procedure
4 ocument ID: of 6 3/23/2018, 3:56 PM 1. Install the clutch master cylinder into the opening in the front of dash. 2. Slide the clutch master cylinder reservoir into the opening on the hood strut bracket. 3. Install the clutch master cylinder reservoir push-in retainer. 4. Raise the vehicle. Important: DO NOT rely on an audible click or a visual verification of the clutch hydraulic hose quick connect fitting connection. 5. Connect the clutch master cylinder hose to the clutch actuator. Push together the clutch hydraulic quick connect fittings, then pull back on the fittings to verify engagement. 6. Check the clutch hydraulic hoses for twists or kinks. 7. Lower the vehicle.
5 5 of 6 3/23/2018, 3:56 PM 8. Install the clutch master cylinder U-bolt (4). 9. Install the clutch master cylinder push on nuts (6). Notice: Refer to Fastener Notice in Cautions and Notices. 10. Install the clutch master cylinder nuts (7). Tighten Tighten the clutch master cylinder nuts (7) to 20 (15 lb ft). 11. Install the clutch master cylinder push rod (3) onto the clutch pedal pin (2). 12. Install the clutch pedal pin retainer (1). 13. Remove the drive side knee bolster. Refer to Driver Knee Bolster Replacement in Instrument Panel, Gauges and Console. 14. Remove the driver side instrument panel insulator. Refer to Instrument Panel Insulator Panel Replacement - Left Side in Instrument Panel, Gauges and Console.
6 ocument ID: of 6 3/23/2018, 3:56 PM 15. Bleed the clutch hydraulic system. Refer to Hydraulic Clutch System Bleeding.
2004 Chevrolet Silverado 3500
CLUTCH PEDAL REPLACEMENT Removal Procedure 1. Remove the driver's side knee bolster and deflector. Refer to Knee Bolster Replacement in Instrument Panel, Gages, and Console. 2. Disconnect and reposition
More informationREMOVAL AND INSTALLATION
501-12-1 Instrument Panel and Console 501-12-1 REMOVAL AND INSTALLATION Instrument Panel Removal CAUTION: Electronic modules are sensitive to static electrical charges. If exposed to these charges, damage
More informationWater Pump Replacement (L4)
1 of 9 9/5/2017, 3:07 PM 2014 Chevrolet Captiva (VIN C) Antara, Captiva Service Manual 5565211 Engine/Propulsion Engine Cooling Repair Instructions Document ID: 2643411 Water Pump Replacement (L4) Special
More informationREMOVAL AND INSTALLATION
308-02B-1 REMOVAL AND INSTALLATION 308-02B-1 Clutch Master Cylinder Material Item Brake Fluid (DOT 3) Specification ESA-M6C25-A Removal WARNING: Brake fluid contains polyglycol ethers and polyglycols.
More information67-69 Camaro. Hydraulic Clutch Master Cylinder Installation Instructions Read These Instructions Completely Before Beginning
67-69 Camaro Hydraulic Clutch Master Cylinder Installation Instructions Read These Instructions Completely Before Beginning These instructions are for hydraulic master cylinder installations using an external
More informationSERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS
SERVICE PROCEDURES FOR CLUTCH HYDRAULIC UNITS SAFETY PROCEDURES Always follow the vehicle manufacturer's recommended safety procedures in your Shop and Owners Manual. REQUIRED TOOLS Flat blade screwdriver,
More informationNotice: Refer to Adding Fluid to the Brake System Notice in the Preface section.
Page 1 of 6 2008 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2065646 Front Disc Brake Pads Replacement Removal Procedure Tools Required J 23738-A Hand Vacuum Pump.
More informationDESCRIPTION AND OPERATION > CLUTCH CONTROLS
Page 1 of 17 2004 Ford Mustang 3.9L Eng Base Service Manual: CLUTCH CONTROLS Print Date: DESCRIPTION AND OPERATION > CLUTCH CONTROLS Fig 1: Identifying Clutch Controls Components Page 2 of 17 The clutch
More informationCaution: Refer to Adding Fluid to the Brake System Caution in the Preface section.
Page 1 of 6 2009 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2094891 Rear Disc Brake Pads Replacement Special Tools J 23738-A Hand Vacuum Pump. Removal Procedure Warning:
More informationminimum allowable level, remove brake fluid to the midway point before proceeding.
1 of 6 12/7/2011 6:45 PM aution: Refer to Brake Dust Caution in Service Precautions. Caution: Refer to Brake Fluid Irritant Caution in Service Precautions. Removal Procedure 1. Inspect the fluid level
More informationBrake Pad: Service and Repair Front PADS - BRAKE FRONT
2005 Dodge Truck RAM 3500 4WD Pickup L6-5.9L DSL Turbo VIN C Page 1 Brake Pad: Service and Repair Front PADS - BRAKE FRONT REMOVAL 1. Raise and support vehicle. 2. Remove the wheel and tire assemblies.
More informationSide Door Sill Trim Plate Package Installation
Page 1 of 5 2014 Chevrolet Equinox Equinox, Terrain VIN L Accessory Installation Manual Accessories Interior Accessories Accessories Document ID: 3619390 Side Door Sill Trim Plate Package Installation
More informationInstallation Instructions HURST ROLL CONTROL Chevrolet Camaro
Installation Instructions HURST ROLL CONTROL 2010-2015 Chevrolet Camaro Catalog# 5671518 WORK SAFELY: Perform this installation on a good clean level surface for maximum safety and with the engine turned
More information1998 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN X Copyright 2013, ALLDATA 10.52SS Page 1
1998 Chevy Truck S10/T10 P/U 2WD V6-4.3L VIN X Copyright 2013, ALLDATA 10.52SS Page 1 Instrument Cluster / Carrier: Service and Repair Instrument Panel Carrier INSTRUMENT PANEL CARRIER REPLACEMENT REMOVAL
More information1999 F-Super Duty Workshop Manual
SECTION 308-02: Clutch Controls 1999 F-Super Duty 250-550 Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 01/2/2000 Clutch Master Cylinder and Reservoir Removal CAUTION: Remove the entire
More informationBrake Pressure Modulator Valve Assembly Replacement (LHD)
Page 1 of 6 2007 Chevrolet Lumina VE Document ID: 1974792 Brake Pressure Modulator Valve Assembly Replacement (LHD) Removal Procedure Caution: Refer to Brake Fluid Caution in the Preface section. Caution:
More informationRear Brake Rotor Replacement
Page 1 of 7 2009 Pontiac G8 G8 Service Manual Suspension Rear Suspension Repair Instructions Document ID: 2094899 Rear Brake Rotor Replacement Removal Procedure Warning: Refer to Safety Glasses Warning
More information2007 Pontiac G BRAKES Disc Brakes - G6
REAR DISC BRAKE PADS REPLACEMENT Removal Procedure CAUTION: Refer to Brake Dust Caution. 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between
More informationCLUTCH GROUP 21A 21A-1 CONTENTS CLUTCH PEDAL AND MASTER CYLINDER... 21A-4 GENERAL INFORMATION... 21A-2 SERVICE SPECIFICATIONS...
21A-1 GROUP 21A CONTENTS GENERAL INFORMATION 21A-2 SERVICE SPECIFICATIONS 21A-2 LUBRICANTS 21A-2 ON-VEHICLE SERVICE 21A-2 PEDAL CHECK 21A-2 BLEEDING 21A-3 PEDAL AND MASTER CYLINDER 21A-4 REMOVAL AND INSTALLATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS A112, A112-1 & A112-93 1979-93 FORD MUSTANG with 7.5" & 8.8" AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR CONVERSION KIT A111-2 (FORD 8" & 9" SMALL BEARING) & REAR CONVERSION KIT A111-3 (FORD 9 TORINO) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking
More informationBLEEDING BRAKE SYSTEM
BLEEDING BRAKE SYSTEM CAUTION: Brake fluid is harmful to painted and plastic surfaces. If brake fluid is spilled onto a painted or plastic surface, immediately wash it with water. Bleed hydraulic system
More information2003 Chevrolet Blazer
INSTRUMENT PANEL (I/P) CARRIER REPLACEMENT Removal Procedure 1. On vehicles equipped with a manual transmission, remove the shift lever. Refer to CONTROL LEVER AND/OR BOOT REPLACEMENT in Manual Transmission
More information350Z / G35 Brake Master Cylinder Brace
Z1 Motorsports 2877 Carrollton - Villa Rica Hwy Carrollton GA 30116 770.838.7777 350Z / G35 Brake Master Cylinder Brace PROLOGUE: Study these instructions completely and thoroughly before proceeding to
More information-Magnet (not completely necessary but can come in handy)
McLeod High Performance Hydraulic Clutch Line Upgrade (05-14 V8) Included in kit: -New clutch line -2 fittings Required Tools: -Floor jack and jack stands (or a lift) -Flashlight -Angled pick tool -13mm
More informationINSTALL INSTRUCTIONS: Blend Door Repair Kit
Dorman Products A/C Blend Door Repair Tool For 2006 Chevrolet Equinox / Pontiac Torrent 902-600 Installation Instructions Parts Included 1. Plastic Replacement Sleeve 2. Mounting Plate 3. Saw 4. Drill
More informationInstallation Instructions HURST ROLL CONTROL Fits: Mustang V8
Installation Instructions HURST ROLL CONTROL Fits: 2005-2009 Mustang V8 Catalog# 5671521 WORK SAFELY! For maximum safety, perform this installation on a clean, level surface and with the engine turned
More informationSECTION 4G PARKING BRAKE TABLE OF CONTENTS
SECTION 4G PARKING BRAKE TABLE OF CONTENTS Description and Operation... 4G-2 Brake Caliper... 4G-2 Component Locator... 4G-3 Repair Instructions... 4G-4 On-Vehicle Service... 4G-4 Parking Brake Adjustment
More informationINSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125 1968-81 CAMARO & FIREBIRD 10 & 12 BOLT W/"C" CLIPS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases
More informationThere are 2 ways of brake fluid replacement: using the Techstream or not using the Techstream.
REPLACEMENT HINT: There are 2 ways of brake fluid replacement: using the Techstream or not using the Techstream. Perform fluid replacement with park (P) selected and the parking brake applied. As brake
More informationInstallation Instructions HURST ROLL CONTROL Challenger SRT8 (w/4 port system)
Installation Instructions HURST ROLL CONTROL 2008-2010 Challenger SRT8 (w/4 port system) Catalog# 5671517 WORK SAFELY: Perform this installation on a good clean level surface for maximum safety and with
More informationTechnical Bulletin. Parts and Service News
Equipment Affected: Part Number Affected: 02026-0430 Technical Bulletin Tractors with Hydro-Vac Brakes Part Description, HYDRO-VAC (VACUUM BOOSTER). Discrepancy, The vacuum booster may not provide enough
More informationOVERHAUL. Using SST, disconnect the 2 brake tubes from the master cylinder. SST
3215 320J001 OVERHAUL 1. DRAIN BRAKE FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface. 2. REMOVE AIR CLEANER CAP SUBASSY 3. REMOVE (a) Disconnect the brake fluid
More informationSPEED CONTROL SYSTEMS SP(SOHC) Page 1. General Description Accelerator Pedal Accelerator Control Cable...9
SP(SOHC) Page 1. General Description...2 2. Accelerator Pedal...4 3. Accelerator Control Cable...9 GENERAL DESCRIPTION 1. General Description A: SPECIFICATION Accelerator pedal Free play At pedal pad 0
More informationClutch, Pressure Plate, And Pilot Bearing Replacement
Page 1 of 6 2008 Chevrolet Aveo : Transmissions > Clutch > Repair Instructions > Clutch, Pressure Plate, And Pilot Bearing Replacement Clutch, Pressure Plate, And Pilot Bearing Replacement CLUTCH, PRESSURE
More informationThis bulletin is being revised to update the Warranty information. Please discard Corporate Bulletin Number (Section Suspension).
1 of 3 8/6/2011 9:07 PM 2004 Chevrolet TrailBlazer - 4WD Bravada, Envoy, Rainier, TrailBlazer VIN S/T Service Manual Document ID: 2088947 Subject: Models: Rattle, Clunk, Pop, Snap Noise from Front and/or
More informationClutch System Troubleshooting Guide-Service Tips
DESCRIPTION AND OPERATION Clutch System The purpose of the clutch is to connect and disconnect a manually operated transmission and the remainder of the powertrain system from the engine. This permits
More informationBrake master cylinder with 25.4 mm (0.999 in.) diameter piston and brake servo, component summary
Page 1 of 11 47-41 Brake master cylinder with 25.4 mm (0.999 in.) diameter piston and brake servo, component summary Note: Brake master cylinders can no longer be disassembled, i.e. there is no provision
More informationFord Focus Front Brake Pad Replacement
2005-2007 Ford Focus Front Brake Pad Replacement Replacing the brake pads on all 2005-2007 Focus models with rear drum brakes. Written By: David Hodson ifixit CC BY-NC-SA www.ifixit.com Page 1 of 16 INTRODUCTION
More information1 of 13 2/10/2016 6:46 PM
1 of 13 2/10/2016 6:46 PM # 12-06-04-003A: Malfunction Indicator Lamp (MIL) Illuminated, Reduced Engine Power Message Displayed, DTC P2135 Set - (Mar 24, 2014) Subject: Malfunction Indicator Lamp (MIL)
More informationTHE safety accessory of the 21 st Century.
00 006 Chevrolet SSR Signal Mirror Installation Instructions THE safety accessory of the st Century. Note: Professional Installation Recommended Warranty does not cover damage to the vehicle or mirror
More information1200 Southeast Ave Tallmadge, Ohio to 2015 Camaro (V6 & V8) Summit Racing Roll Stop Install Instructions.
1200 Southeast Ave Tallmadge, Ohio 44278 2010 to 2015 Camaro (V6 & V8) Summit Racing Roll Stop Install Instructions Part # SUM-760006 Parts Included in System: Qty Description Qty Description 2 Stainless
More informationALLDATA Online Saturn L200 L4-2.2L VIN F - Base Brake Bleeding. Base Brake Bleeding
Page 1 of 9 Base Brake Bleeding BASE BRAKE BLEEDING TOOLS REQUIRED J-439l5 Brake Bleed Adapter J29532 Pressure Bleeder MANUAL BLEEDING NOTICE: Brake fluid is corrosive to painted surfaces. Take care not
More informationDESCRIPTION & OPERATION
2004 BRAKES Disc - TSX DESCRIPTION & OPERATION WARNING: DO NOT use air pressure or a dry brush to clean brake assemblies. Avoid breathing brake dust. Use OSHA-approved vacuum cleaner for cleaning and collecting
More informationCLUTCH Toyota Celica DESCRIPTION ADJUSTMENTS CLUTCH PEDAL HEIGHT Clutch. Celica
CLUTCH 1993 Toyota Celica 1993 Clutch Celica DESCRIPTION The single, dry disc type clutch uses a hydraulically operated master cylinder and a release cylinder mounted on clutch housing. Clutch release
More informationDRIVE AXLES. Differentials & Axle Shafts - Corvette
DESCRIPTION & OPERATION 1998-99 DRIVE AXLES Differentials & Axle Shafts - Corvette A Getrag 625 model differential is used on both the automatic and manual transmissions. Differential carrier and case
More information2001 Honda Civic EX ACCESSORIES & EQUIPMENT' 'Cruise Control Systems - Civic & CR-V 2001 ACCESSORIES & EQUIPMENT
DESCRIPTION 2001 ACCESSORIES & EQUIPMENT Cruise Control Systems - Civic & CR-V Cruise control system uses mechanical and electrically operated devices to maintain vehicle speed settings greater than 25
More informationUNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS Ford Ra... UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS TECHNICAL SERVICE BULLETIN
Page 1 of 5 UNRESPONSIVE CLUTCH: AIR ENTRAPPED IN HYDRAULIC SYS TECHNICAL SERVICE BULLETIN Reference Number(s): 93-12-19, Date of Issue: June 9, 1993 CONDITIONS CLUTCH - "SOFT" UNRESPONSIVE CLUTCH PEDAL
More information2010 Toyota Prius Repair Manual
REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. NOTICE: When the brake pedal is depressed or the door courtesy switch is turned on even if the power switch is off,
More informationGENERAL PROCEDURES. Component Bleeding. Master Cylinder Priming In-Vehicle or Bench
206-00-1 Brake System General Information 206-00-1 GENERAL PROCEDURES Component Bleeding Special Tool(s) Worldwide Diagnostic System (WDS) 418-F224, New Generation STAR (NGS) Tester 418-F052, or equivalent
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION REAR BRAKE CALIPER NOTE: For rear disc pad removal and installation, DO NOT disconnect brake hose from caliper (wire aside). Replace all pads on an axle if wear indicator on any
More information1994 Mazda MX-5 Miata. CLUTCH 1994 Clutch
CLUTCH 1994 Clutch DESCRIPTION Miata uses a hydraulically operated clutch. HYDRAULIC SYSTEM BLEEDING 1. Remove bleeder screw cap, located at clutch release cylinder. Install vinyl hose onto bleeder screw.
More information1 of 11 4/11/ :35 AM
1 of 11 4/11/2015 11:35 AM Rear Disc Brake Pads Replacement Special Tools * KM-6007 Resetting Tool * KM-6007-30 Adaptor Removal Procedure 2 of 11 4/11/2015 11:35 AM Caution: Refer to Brake Dust Caution
More informationILLUSTRATION ILLUSTRATION
ILLUSTRATION ILLUSTRATION REMOVAL 1. DISABLE BRAKE CONTROL (a) Wait at least 2 minutes after the power switch off. When the brake pedal is depressed or the door courtesy switch is turned on even if the
More information1992 Clutch. Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT
Article Text ARTICLE BEGINNING 1992 Clutch Eclipse, Expo/Expo LRV, Galant, Mirage, Precis, 3000GT DESCRIPTION All clutches are single disc type. Pressure plate assembly uses a diaphragm spring to engage
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationText in Illustration
ON-VEHICLE INSPECTION If using a dropper to adjust the fluid amount, make sure that the dropper has not been used with mineral oils, water or deteriorated brake fluid. Sealed areas may deteriorate and
More informationGOCATUTV.COM Hydraulic Brake line Lock for UTV / Side by Sides
GOCATUTV.COM Hydraulic Brake line Lock for UTV / Side by Sides WARNING! Hydraulic Brake line locks are intended to supplement park brake locks and should only be used in conjunction with your factory park
More information2004 DRIVELINE/AXLE. Rear Drive Axle - Corvette. Fastener Tightening Specifications Specification Application
2004 DRIVELINE/AXLE Rear Drive Axle - Corvette SPECIFICATIONS FASTENER TIGHTENING SPECIFICATIONS Fastener Tightening Specifications Specification Application Metric English Differential Case Bolts 55 N.m
More informationShift Cable: Service and Repair Allison - Automatic Transmission
2002 Chevy Truck C 2500 P/U 2WD V8-6.6L DSL Turbo VIN 1 Page 1 Shift Cable: Service and Repair Allison - Automatic Transmission Front/Column End Automatic Transmission Range Selector Cable Replacement
More informationDESCRIPTION & OPERATION
CRUISE CONTROL SYSTEM 1997 ACCESSORIES/SAFETY EQUIP General Motors Corp. - Cruise Control System DESCRIPTION & OPERATION WARNING: To avoid injury from accidental air bag deployment, read and carefully
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-2 1955-70 FULL SIZE CHEVROLET Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationSECTION B Supplemental Restraint System
501-20B-i Supplemental Restraint System 501-20B-i SECTION 501-20B Supplemental Restraint System CONTENTS PAGE Restraints Control Module (RCM)... 501-20B-2 501-20B-2 Supplemental Restraint System 501-20B-2
More informationInstallation Instructions HURST ROLL CONTROL Ford Mustang. Catalog#
Installation Instructions HURST ROLL CONTROL 2010-2014 Ford Mustang 1591520 REV01 09/22/15 Catalog# 5671519 WORK SAFELY: Perform this installation on a good clean level surface for maximum safety and with
More informationMicrolight Trike Edge-X 582. Hand Control Equipment & Modifications
Microlight Trike Edge-X 582 Hand Control Equipment & Modifications The following information details the hand control equipment and other minor modifications that have been undertaken to allow a quadriplegic
More informationOnline Service Center for Monaco Coach
Online Service Center for Monaco Coach TROUBLESHOOTING TIPS [ back to the Online Service Center main page ] CAUTION: The Air Suspension System must be turned off at the System Power switch when the vehicle
More information1993 AEROSTAR, BRONCO, EXPLORER, F SERIES, F-47, RANGER
CLUTCH SOFT UNRESPONSIVE CLUTCH Article No. PEDAL AIR ENTRAPPED IN HYDRAULIC 93-12-19 SYSTEM SERVICE TIPS CLUTCH HYDRAULIC UNABLE TO RELEASE AIR ENTRAPPED IN SYSTEM SERVICE TIPS CLUTCH HYDRAULIC BLEED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS INSTALLATION INSTRUCTIONS FOR A136 REAR DRUM TO DISC BRAKE CONVERSION KIT for 1970-75 Jeep, CJ SERIES with Dana 44 flanged axle Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationC40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
More informationPARTS Stainless Steel Stainless Steel Brakeline- to Master Bracket. 1/8 NPT plug (2) 1/4-20 Soc Screw (2) Solenoid Valve.
HURST ROLL CONTROL INSTALLATION INSTRUCTIONS # 5671518 2010 and up CAMARO 2011 by Hurst Performance Thank you for purchasing the Hurst Roll Control system which features an advanced design high quality
More informationHAND THROTTLE KIT For Workman 3000 Series
FORM NO. 7 6 MODEL NO. 0746 INSTALLATION INSTRUCTIONS HAND THROTTLE KIT For Workman 000 Series. Position vehicle on a clean, level surface, stop engine, engage parking brake and remove key from ignition
More informationINDEX. NOTE: Part number ES381RL Camaro Outer Tie Rod Ends must be used with this rack and pinion kit.
INDEX NOTE: Before beginning you must first measure the width of your front end from LEFT outer tie rod end zirc to the RIGHT outer tie rod end zirc to determine the overall width of your front end. Write
More informationBRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
More informationModels Affected: Certain 2013 Model Year Propane Vision Buses Equipped with Ford 6.8L Engines CORRECTIVE ACTION ---- PROCEDURE
Models Affected: Certain 2013 Model Year Propane Vision Buses Equipped with Ford 6.8L Engines ISSUE Certain 2013 model year propane Vision buses equipped with Ford 6.8L engines may not have the service
More informationMaintenance Schedules - Diesel Engines
Page 1 of 12 Published: Nov 20, 2008 Maintenance Schedules - Diesel Engines Description Nm lb-ft Seat frame fixing Torx screws 40 30 Seat belt fixing Torx screws 40 30 Road wheel nuts 140 103 M12 tie rod
More informationWater Pump Replacement (L4)
2011 Chevrolet Equinox Equinox, Terrain VIN L Service Manual Water Pump Replacement (L4) Special Tools EN-43651 Water Pump Holding Tool For equivalent regional tools, refer to Special Tools. Removal Procedure
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationDanger: To avoid any vehicle damage, serious personal injury or death:
Service Information Document ID: 5027339 Lifting and Jacking the Vehicle Danger: To avoid any vehicle damage, serious personal injury or death, always use the jack stands to support the vehicle when lifting
More information2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA Page 1
2001 Chrysler Truck PT Cruiser L4-2.4L VIN B Copyright 2013, ALLDATA 10.52 Page 1 Timing Belt: Service and Repair Timing Belt REMOVAL 1. Disconnect negative battery cable. 2. Raise vehicle on hoist. Remove
More information1. Remove the battery tray. For additional information, refer to Battery Tray ( )
Page 1 of 11 Removal 1. Remove the battery tray. For additional information, refer to Battery Tray (86.15.11) 2. Remove the air cleaner. For additional information, refer to Air Cleaner (19.10.05) 3. NOTE
More informationTechnical Support (707)
Installation Instructions CONSOLE MEGASHIFTER Fits: 1982-1992 Camaro & Firebird w/automatic Transmission *except 1988-1992 Firebird Formula Model Catalog # 80692 WORK SAFELY! For maximum safety, perform
More information1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans
DESCRIPTION & OPERATION 1999-2000 BRAKES Disc & Drum - Trucks & Vans WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see appropriate ANTI-LOCK article.
More informationInstallation of Hydraulic Disc Brake System with the ActiBrake Actuator Sand Drive Fort Worth, Texas
Installation of Hydraulic Disc Brake System with the ActiBrake Actuator 7600 Sand Drive Fort Worth, Texas 76118 800-756-3425 The Integrated Hydraulic Brake System page 1 ActiBrake - Part of a System ActiBrake
More informationInstallation Instructions for TJ Jeep s Fiberglass Replacement Bodies and Parts
Installation Instructions for 1997-2006 TJ Jeep s Fiberglass Replacement Bodies and Parts Getting started: We recommend that you take pictures as you dismantle your Jeep. These pictures will help you when
More informationA. VEHICLE INSPECTION PROCEDURE
MAZDA3 AND MAZDA5 POWER STEERING VOLUNTARY SAFETY RECALL ATTACHMENT IV MAZDA3 AND MAZDA5 POWER STEERING VOLUNTARY SAFETY RECALL A. VEHICLE INSPECTION PROCEDURE 1. Verify that the vehicle is within the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationCHAPTER 21 ENVIRONMENT CONTROL. Section Title Page
CHAPTER 21 ENVIRONMENT CONTROL Section Title Page 21-00 Description........................................ 21.1 21-10 Ventilation........................................ 21.3 21-11 Nose Vent................................
More informationClick Here for Printable PDF File. CHAPTER 3 - BASIC INFORMATION for PERFORMING HYDRAULIC SYSTEM MAINTENANCE
HWH Online Technical School Lesson 1: Introduction to Hydraulics Chapter 3 - "BASIC INFORMATION for PERFORMING HYDRAULIC SYSTEM MAINTENANCE" (Filename: ML57000-012-CH3.DOC Revised: 22APR16) Click Here
More informationPlastic Trim Removal Tool Phillips Screwdriver (for vehicles w/ shift boot) Wire Cutter. (FOR VEHICLES w/o A SHIFT BOOT)
INSTALLATION INSTRUCTIONS C10FL0 DESCRIPTION: STI CVT SHIFT KNOB STI CVT SHIFT KNOB TOOLS REQUIRED: PARTS IDENTIFICATION: Plastic Trim Removal Tool Phillips Screwdriver (for vehicles w/ shift boot) Wire
More informationHURST ROLL CONTROL INSTALLATION INSTRUCTIONS # CHALLENGER SRT8 (w/ 4 port system)
HURST ROLL CONTROL INSTALLATION INSTRUCTIONS # 5671517 2008-2010 CHALLENGER SRT8 (w/ 4 port system) Thank you for purchasing the Hurst Roll Control system which features an advanced design high quality
More informationRMK HANDLEBAR KIT P/N ; ; APPLICATION BEFORE YOU BEGIN KIT CONTENTS. Verify accessory fitment at Polaris.com.
RMK HANDLEBAR KIT P/N 2883835; 2883836; 2883837 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for.
More informationHydraulic Brakes and clutch on cars, vans, motorbikes etc work the same
bleed clutch or brake.txt USE DOT4 Brake/Clutch fluid CAUTION brake fluid is corrosive, wash off hands and rinse off any spills IMMEDIATELY with lots of clean water --- Brake fluid will strip paint if
More information"Engineered to Ride, Built to Last "
Congratulations on your purchase of an Arnott air suspension product. We at Arnott Incorporated are proud to offer a high quality product at the industry s most competitive pricing. Thank you for your
More information1 of 27 7/21/2015 3:33 PM
1 of 27 7/21/2015 3:33 PM WM 489819 Removing and installing hydraulic pump - as of model year 2009 Tools Technical values Information 2 of 27 7/21/2015 3:33 PM Overview of hydraulic pump Preliminary work
More informationPage 1 of 11 2009 Hummer H2 6.2L Eng 1Search Print Date: SHIFT LOCK CONTROL SYSTEM Repair Instructions Automatic Transmission Shift Lock Control Actuator Replacement Removal Procedure NOTE: After assembling
More informationSECTION 4A HYDRAULIC BRAKES
SECTION 4A HYDRAULIC BRAKES CAUTION: Disconnect the negative battery cable before removing or installing any electrical unit or when a tool or equipment could easily come in contact with exposed electrical
More informationService Information Chevrolet Camaro 3.6L LFX Engine. Camshaft Position Actuator Replacement - Bank 1. Document ID:
Service Information 2014 Chevrolet Camaro 3.6L LFX Engine Camshaft Position Actuator Replacement - Bank 1 Document ID: 2900815 Special Tools Removal Procedure EN49982-1 Timing Chain Retainer EN49982-2
More informationFUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY
FUEL LEVEL SENSOR UNIT, FUEL FILTER AND FUEL PUMP ASSEMBLY Removal and Installation REMOVAL WARNING: Follow the "General Precautions" before working on the fuel system. Refer to "General Precautions".
More informationBRAKE SYSTEM Article Text 1996 Toyota RAV4 For Copyright 1998 Mitchell Repair Information Company, LLC Wednesday, September 13, :30PM
Article Text ARTICLE BEGINNING 1996 BRAKES Toyota - Disc & Drum RAV4 * PLEASE READ THIS FIRST * WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT BIG BRAKE CONVERSION KIT A112-5 1987-93 FORD MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and
More information