Caution: Refer to Adding Fluid to the Brake System Caution in the Preface section.
|
|
- Annabel Ford
- 6 years ago
- Views:
Transcription
1 Page 1 of Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: Rear Disc Brake Pads Replacement Special Tools J A Hand Vacuum Pump. Removal Procedure Warning: Refer to Safety Glasses Warning in the Preface section. Warning: Refer to Brake Dust Warning in the Preface section. Warning: Refer to Brake Fluid Warning in the Preface section. Warning: Refer to Brake Fluid Irritant Warning in the Preface section. Caution: Refer to Adding Fluid to the Brake System Caution in the Preface section. Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface section. Danger: To avoid any vehicle damage, serious personal injury or death when major components are removed from the vehicle and the vehicle is supported by a hoist, support the vehicle with jack stands at the opposite end from which the components are being removed and strap the vehicle to the hoist. 1. Inspect the fluid level in the master cylinder reservoir (1) General Motors Corporation. All rights reserved.
2 Page 2 of 6 If the brake fluid level is midway between the maximum fill level and the minimum allowable level, no brake fluid needs to be removed from the master cylinder reservoir (1) before proceeding. Note: DO NOT completely empty the master cylinder reservoir (1) or remove any brake lines otherwise complete bleeding of the braking system will be necessary. Note: DO NOT re use the removed fluid. If the brake fluid level is higher than midway between the maximum fill level and the minimum allowable level, syphon the brake fluid to the midway point using a hand vacuum pump (2) before proceeding. 2. Raise and support the vehicle. Refer to Lifting and Jacking the Vehicle. 3. Remove rear wheels. Refer to Tire and Wheel Removal and Installation. 4. Install 2 wheel nuts (3) in reverse to opposite wheel studs to retain the brake disc to the hub. Note: Position the ends of the G-clamp against the rear of the brake caliper (1) and against the outboard brake pad (2). 5. Install a large G-clamp over the body of the brake caliper (1). 6. Tighten the G-clamp until the brake caliper piston bottoms out in the brake caliper bore. 7. Remove the G-clamp from the brake caliper (1).
3 Page 3 of 6 Note: Bolts with micro-encapsulated thread sealant must be discarded after removal. 8. Remove the brake caliper lower guide pin bolt (1) and discard. Caution: Support the brake caliper with heavy mechanic wire, or equivalent, whenever it is separated from its mount and the hydraulic flexible brake hose is still connected. Failure to support the caliper in this manner will cause the flexible brake hose to bear the weight of the caliper, which may cause damage to the brake hose and in turn may cause a brake fluid leak. Note: DO NOT disconnect the brake hose (1) from the brake caliper (3). 9. Pivot the brake caliper (3) upward and secure with heavy mechanics wire (2), or equivalent.
4 Page 4 of Remove the brake pads (5) from the brake caliper anchor plate (4). 11. Remove the brake pad retainers (6) from the brake caliper anchor plate (4). 12. Clean the brake pad retainer mating surfaces of the brake caliper anchor plate (4). Note: Inspect the brake caliper guide pins for freedom of movement and the condition of the guide pin boots. This is achieved by moving the guide pins inboard and outboard within the brake caliper anchor plate (4) bores, without disengaging the slides from the boots. 13. Inspect the brake caliper guide pins and boots for the following conditions: Restricted brake caliper guide pin movement Too much brake caliper guide pin play in the brake caliper anchor plate (4) Seized or binding brake caliper guide pins Split or torn boots 14. If any of the conditions listed are found, overhaul or replace the brake caliper (3). Installation Procedure Warning: Refer to Safety Glasses Warning in the Preface section. Warning: Refer to Brake Dust Warning in the Preface section. Warning: Refer to Brake Fluid Warning in the Preface section. Warning: Refer to Brake Fluid Irritant Warning in the Preface section. Caution: Refer to Adding Fluid to the Brake System Caution in the Preface section. Caution: Refer to Brake Fluid Effects on Paint and Electrical Components Caution in the Preface section. Danger: To avoid any vehicle damage, serious personal injury or death when major components are removed from the vehicle and the vehicle is supported by a hoist, support the vehicle with jack stands at the opposite end from which the components are being removed and strap the vehicle to the hoist. 1. Thoroughly clean both piston to brake pad contact faces as required.
5 Page 5 of 6 2. Install the brake pad retainers (6) to the brake caliper anchor plate (4). Note: The brake pads (5) are marked as left hand inner and right hand inner and must only be fitted to their respective positions to optimize brake pad life and performance. 3. Install the brake pads (5) to the brake caliper anchor plate (4). Caution: Make sure the brake hose is not twisted or kinked after installation. Damage to the hose could result. 4. Remove the mechanics wire (2) or equivalent, and rotate the brake caliper (3) into position over the brake pads (5) and to the brake caliper anchor plate (4). Make sure the brake hose (1) is correctly located in its mounting bracket. Caution: Refer to Fastener Caution in the Preface section.
6 Page 6 of 6 5. Install the NEW lower brake caliper guide pin bolt (1) and tighten to 42 N m (31 lb ft). 6. Remove the 2 wheel nuts retaining the brake disc to the hub. 7. Install the rear wheels. Refer to Tire and Wheel Removal and Installation. 8. Lower the vehicle to the ground. 9. With the engine off, gradually apply the brake pedal approximately 2/3 of its travel distance. 10. Slowly release the brake pedal. 11. Repeat steps 9 and 10 until a firm brake pedal is obtained. This will correctly seat the brake caliper pistons and brake pads. 12. Fill the master cylinder reservoir to the correct level. Refer to Master Cylinder Reservoir Filling. 13. Burnish (bed in) the brake pads and brake discs. Refer to Brake Pad and Rotor Burnishing.
Notice: Refer to Adding Fluid to the Brake System Notice in the Preface section.
Page 1 of 6 2008 Pontiac G8 G8 Service Manual Brakes Disc Brakes Repair Instructions Document ID: 2065646 Front Disc Brake Pads Replacement Removal Procedure Tools Required J 23738-A Hand Vacuum Pump.
More informationRear Brake Rotor Replacement
Page 1 of 7 2009 Pontiac G8 G8 Service Manual Suspension Rear Suspension Repair Instructions Document ID: 2094899 Rear Brake Rotor Replacement Removal Procedure Warning: Refer to Safety Glasses Warning
More information2007 Pontiac G BRAKES Disc Brakes - G6
REAR DISC BRAKE PADS REPLACEMENT Removal Procedure CAUTION: Refer to Brake Dust Caution. 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between
More information2005 Cadillac CTS BRAKES Disc Brakes - CTS
Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid
More information2005 Cadillac CTS BRAKES Disc Brakes - CTS
Removal Procedure 1. Inspect the fluid level in the brake master cylinder reservoir. 2. If the brake fluid level is midway between the maximum-full point and the minimum allowable level, no brake fluid
More informationALLDATA Online Hummer H2 V8-6.0L - Brake Pads Replacement - Rear. Brake Pads Replacement - Rear
Page 1 of 5 Home Account Contact ALLDATA Log Out Help PAUL REDEHOFT Select Vehicle New TSBs Technician's Reference Component Search: OK 2005 Hummer H2 V8-6.0L Conversion Calculator Vehicle Level Brakes
More informationminimum allowable level, remove brake fluid to the midway point before proceeding.
1 of 6 12/7/2011 6:45 PM aution: Refer to Brake Dust Caution in Service Precautions. Caution: Refer to Brake Fluid Irritant Caution in Service Precautions. Removal Procedure 1. Inspect the fluid level
More information2004 Ford Expedition
DISC BRAKE PADS Removal (Front) WARNING: The electrical power to the air suspension system must be shut off prior to hoisting, jacking or towing an air suspension vehicle. This can be accomplished by turning
More informationService Procedure. 1. Raise the vehicle on a suitable hoist and support as necessary. 2. Remove both front tires and wheels.
Service Procedure The following procedure provides instructions for repairing a corrosion condition where the front wheel speed sensor mounts on the front wheel bearing assembly. 1. Raise the vehicle on
More information1 of 9 7/19/2016 5:35 PM
1 of 9 7/19/2016 5:35 PM PADS - FRONT/REAR BRAKE - SRT8 STANDARD PROCEDURE BRAKE PAD BURNISHING CAUTION: After installing NEW brake pads, keep in mind that braking effectiveness might be somewhat reduced
More informationBRAKE SYSTEM Return To Main Table of Contents
BRAKE SYSTEM Return To Main Table of Contents GENERAL... 2 BRAKE PEDAL... 10 MASTER CYLINDER... 13 BRAKE BOOSTER... 16 BRAKE LINE... 18 PROPORTIONING VALVE... 19 FRONT DISC BRAKE... 20 REAR DRUM BRAKE...
More information2005 Dodge Grand Caravan
REMOVAL REMOVAL - REAR DISC BRAKE SHOES 1. Raise vehicle. (Refer to LUBRICATION & MAINTENANCE/HOISTING - STANDARD PROCEDURE). 2. Remove rear wheel and tire assemblies from vehicle. 3. Remove the caliper
More informationDura Force Disc Brake System Service Manual
TS 20809_a 3501 Shotwell Drive ISO/TS 16949:2002 Registered (PH): 937.743.8125 Franklin, OH 45005 www.waltheremc.com (FX): 937.743.8232 Table of Contents General Description 1 3 Fastener Torque Chart 4
More informationM-2300-T 6-Piston Mustang Brake Kit INSTALLATION INSTRUCTIONS
Please visit www.fordracingparts.com for the most current instruction information!!! PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT UNDERSTAND THE
More informationBRAKE SYSTEM Article Text 1996 Toyota RAV4 For Copyright 1998 Mitchell Repair Information Company, LLC Wednesday, September 13, :30PM
Article Text ARTICLE BEGINNING 1996 BRAKES Toyota - Disc & Drum RAV4 * PLEASE READ THIS FIRST * WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION REAR DISC BRAKE PADS Removal Raise and support vehicle. Remove wheels. Thoroughly clean outside of caliper to prevent dust and dirt from entering inside. Support caliper with a piece
More informationDISC BRAKE/DUAL MASTER CYLINDER CONVERSION. Tools, Equipment and Supplies Needed:
Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarification. It is important to note that these instructions contain
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR FORGED SUPERLITE BIG BRAKE FRONT HUB KIT WITH 3.00 DIAMETER VENTED ROTOR 968-969 FORD MUSTANG (DISC BRAKE SPINDLE ONLY) PART NUMBER GROUP 0-950 WARNING INSTALLATION OF THIS KIT
More informationParking brake Mechanical brake acting on rear wheels
11 Brake System 11.1 General SPECIFICATIONS EJTC0010 Master cylinder Type Tandem type I.D. mm(in.) 20.64 mm (0.813 in.) Fluid level warning sensor Provided Brake booster Type Vacuum Boosting ratio 4.0
More informationInstallation Instructions
Preparing your vehicle to install your brake system upgrade 1. Rack the vehicle. 2. If you don t have a rack, then you must take extra safety precautions. 3. Choose a firmly packed and level ground to
More information1 of 11 4/11/ :35 AM
1 of 11 4/11/2015 11:35 AM Rear Disc Brake Pads Replacement Special Tools * KM-6007 Resetting Tool * KM-6007-30 Adaptor Removal Procedure 2 of 11 4/11/2015 11:35 AM Caution: Refer to Brake Dust Caution
More informationSUBJECT: Front Brake Pulsation During Light To Moderate Brake Application
NUMBER: GROUP: DATE: 05-003-02 REV. B Brakes Dec. 16, 2002l This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced,
More informationM-2300-WR Focus ST Performance RS Rear Brake Kit
Please visit www. performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO
More informationBrake Pad: Service and Repair Front PADS - BRAKE FRONT
2005 Dodge Truck RAM 3500 4WD Pickup L6-5.9L DSL Turbo VIN C Page 1 Brake Pad: Service and Repair Front PADS - BRAKE FRONT REMOVAL 1. Raise and support vehicle. 2. Remove the wheel and tire assemblies.
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR SUPERLITE 6 BIG BRAKE FRONT HAT KIT PRO STREET APPLICATION,.90 DIAMETER VENTED ROTOR 99-00 MUSTANG (5 LUG, STOCK OFFSET) PART NUMBER GROUP 0-907 INSTALLATION OF THIS KIT SHOULD
More informationBrake System H TX, H2.0TXS [B475]; H TX [B466] Safety Precautions Maintenance and Repair
HMM180001 Brake System H1.5-1.8TX, H2.0TXS [B475]; H2.5-3.5TX [B466] Safety Precautions Maintenance and Repair When lifting parts or assemblies, make sure all slings, chains, or cables are correctly fastened,
More informationREMOVAL & INSTALLATION
REMOVAL & INSTALLATION FRONT DISC BRAKE PADS 1. Raise and support front of vehicle. Remove wheels. Remove caliper bolt and brakeline bracket bolts. Pivot caliper aside. Remove pads and pad shim. Remove
More informationM-2300-M Mustang GT Rear Disc Brake Bracket Kit INSTALLATION INSTRUCTIONS
Please contact the Tech Line for the most current instruction information (800) 367-3788!!! PLEASE READ THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION!!! INTRODUCTION: This kit allows for the
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR CONVERSION KIT A111-2 (FORD 8" & 9" SMALL BEARING) & REAR CONVERSION KIT A111-3 (FORD 9 TORINO) Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking
More informationTOYOTA TUNDRA BIG BRAKE KIT Section I - Installation Preparation
TOYOTA TUNDRA 2007- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-34070 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.8 OFFSET) BOLT CHEVY PART NUMBER GROUP 0-7 INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED BY PERSONS EXPERIENCED
More information2003 Jaguar X-Type BRAKES' 'Disc - X-Type
REAR DISC BRAKE CALIPER WARNING: Brake dust, if inhaled can damage your health. Always remove brake dust using a vacuum brush. Do not use a compressed air line to disperse brake dust into the atmosphere.
More informationA proportioning valve is used to regulate brake pressure between front and rear brakes. Rear brakes on all models are self-adjusting.
Page 1 of 21 ARTICLE BEGINNING DESCRIPTION & OPERATION WARNING: For warnings and procedures regarding vehicles equipped with Anti- Lock Brake Systems (ABS), see ANTI-LOCK BRAKE SYSTEM article in the BRAKES
More informationBRAKE SYSTEM Article Text 1992 Mitsubishi Mirage For a a a a a Copyright 1998 Mitchell Repair Information Company, LLC Monday, April 01, :05AM
Article Text ARTICLE BEGINNING 1992 BRAKES Chrysler Motors/Mitsubishi - Disc & Drum Chrysler Motors: Colt, Colt 200, Colt Vista, Ram-50, Stealth, Summit, Summit Wagon; Mitsubishi: Diamante, Eclipse, Expo/Expo
More information2003 Infiniti G35. CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out.
FRONT & REAR DISC PADS CAUTION: When brake caliper is removed, DO NOT depress brake pedal, or piston will pop out. To determine which brake system vehicle is equipped with, see MODEL IDENTIFICATION. Removal
More informationFRONT BRAKE COMPONENTS
BR18 BRAKE SYSTEM FRONT BRAKE COMPONENTS REPLACEMENT OF BRAKE PADS HINT: If a squealing noise occurs from the front brakes while driving, check the pad wear indicator. If there are traces of the indicator
More informationLEXUS IS 250 Front Performance Brake Kit Section I - Installation Preparation
LEXUS IS 250 Front 2006- Performance Brake Kit Section I - Installation Preparation Part Number: PTR09-53080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A120-4 & A120-5 1964-1/2-66 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION REAR KIT SUM-BK1423 1999-2009 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take the time to read
More information82-92 CAMARO, FIREBIRD/78-87 REGAL, MONTE CARLO, GRAND PRIX/ S-10 RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS
82-92 CAMARO, FIREBIRD/78-87 REGAL, MONTE CARLO, GRAND PRIX/ S-10 RACE/STREET 4-PISTON FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 82-92 CAMARO/78-87 REGAL YOU WILL NEED TO MODIFY
More informationTools, Equipment and Supplies Needed:
153-162 DISC BRAKE/DUAL MASTER CYLINDER CONVERSION Please take the time to read the enclosed instructions carefully. If you have any questions, call our Product Assistance personnel for clarifi cation.
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 970-973 FORD MUSTANG (DRUM / DISC SPINDLE) PART NUMBER GROUP 0-905 WARNING INSTALLATION OF THIS KIT SHOULD ONLY
More informationINSTALLATION INSTRUCTIONS FOR REMOTE MASTER CYLINDER KIT PART NUMBER(S) , , , ,
INSTALLATION INSTRUCTIONS FOR REMOTE MASTER CYLINDER KIT PART NUMBER(S) 260-3372, 260-3374, 260-3376 260-3378, 260-3380, 260-5920 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND COMPETENT
More informationInstallation Guide: Front Brake Pad
Installation Guide: Front Brake Pad Ninety percent of the brake pad changes you make during the life of your vehicle will be to the front brakes because they do 60% to 70% of the braking. On most cars,
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (.36 OFFSET) BIG BEARING FORD PART NUMBER GROUP 0-739 INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KITS A148-9 & A148-15 1949-54 Chevy Trucks Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please take the time to
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.8 OFFSET) BOLT CHEVY PART NUMBER 0-7* WARNING INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED BY PERSONS EXPERIENCED
More information1969 Camaro. Concourse Style Disc Brake Conversion Kit Instllation Instructions
Concourse Style Disc Brake Conversion Kit Instllation Instructions 1969 Camaro (1970 Chevelle Kit Shown) This document contains our regular disc brake conversion instructions with the addition of GM assembly
More informationASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.75 OFFSET) CAMARO / FIREBIRD
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (.75 OFFSET) 993-997 CAMARO / FIREBIRD PART NUMBER GROUP 0-78 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER VENTED ROTOR (. OFFSET) 005 - PRESENT MUSTANG 8.8 (5 LUG) PART NUMBER GROUP 0-98 INSTALLATION OF THIS KIT SHOULD ONLY
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.50 OFFSET) BIG BEARING FORD, NEW STYLE PART NUMBER 0-70* WARNING INSTALLATION OF THIS KIT SHOULD ONLY BE PERFORMED
More informationSCION tc BIG BRAKE KIT Section I - Installation Preparation
SCION tc 2005- BIG BRAKE KIT Section I - Installation Preparation Part Number: PTR09-21080 Kit Contents Item # Quantity Reqd. Description 1 1 Brake Rotor, LH Front 2 1 Brake Rotor, RH Front 3 1 Brake Caliper
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT DISC BRAKE CONVERSION KITS: A132-1, A133, A133-1 A134, A134-1 1968-73 MUSTANG/FORD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Please
More information2012 Taurus Workshop Manual. DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011
SECTION 204-01: Front Suspension DISASSEMBLY AND ASSEMBLY Procedure revision date: 07/14/2011 Strut and Spring Assembly Material Item Silicone Brake Caliper Grease and Dielectric Compound XG-3-A Specification
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FRONT BIG BRAKE CONVERSION KIT A112-5 1987-93 FORD MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read and
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A136-1 1976-86 AMC 20 AXLES WITH WARN FULL FLOATING AXLE CONVERSION Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs.
More informationA/F/X Body GM Installation Instructions
A/F/X Body GM Installation Instructions Power Disc Conversion 64-72 A Body / 67-69 F Body / 68-74 X Body 9 slimline booster pictured Your new disc brake conversion kit can be bolted up with standard hand
More informationASSEMBLY INSTRUCTIONS FOR
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR AXLE KIT WITH.9 DIAMETER VENTED ROTOR (.36 OFFSET) MOPAR 8-3/ DANA 60 FOR USE WITH GREEN* NON-ADJUSTABLE BEARING PART NUMBER GROUP 0-7-B DISC BRAKES SHOULD
More information2000 Saturn LS2. Fig. 2: Identifying Self-Adjuster Components (Drum Brakes) Courtesy of GENERAL MOTORS CORP. WHEEL CYLINDERS
Fig. 2: Identifying Self-Adjuster Components (Drum Brakes) WHEEL CYLINDERS Raise and support vehicle. Remove brake shoes. See REAR BRAKE SHOES. Disconnect brake pipe from wheel cylinder. See Fig. 3. Remove
More information1 Part Number: M-2300-Y Part Description: S550 Mustang-Shelby Brake Upgrade Kit Installation Instructions
Please visit www.performanceparts.ford.com for the most current instruction and warranty information. PLEASE READ ALL OF THE FOLLOWING INSTRUCTIONS CAREFULLY PRIOR TO INSTALLATION. AT ANY TIME YOU DO NOT
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1980-1987 GENERAL MOTORS G BODY DISC SPINDLE PART NUMBER GROUP -508-B WARNING INSTALLATION OF THIS KIT SHOULD ONLY
More informationThis chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models.
KYMCO MXU 500i/700i Repair Manual Brake System 9.Brake System This chapter covers the location and servicing of the front brake components for the KYMCO MXU 700i and MXU 500i models. 1.Brake Discs... 9-3
More informationBRAKE SYSTEM Nissan 240SX DESCRIPTION BRAKE BLEEDING * PLEASE READ FIRST * BLEEDING PROCEDURES ADJUSTMENTS BRAKE PEDAL HEIGHT SPECS TABLE
BRAKE SYSTEM 1990 Nissan 240SX 1990 BRAKE SYSTEMS Nissan Disc & Drum Axxess, Maxima, Pathfinder, Pickup, Pulsar NX, Sentra, Stanza, 240SX, 300ZX DESCRIPTION All brake systems are hydraulically operated
More informationINSTALLATION INSTRUCTION 89400
INSTALLATION INSTRUCTION 89400 FOR RANCHO SUSPENSION SYSTEM RS66400B: 2012 RAM 1500 4WD. READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev B IMPORTANT NOTES! WARNING:
More informationSUBJECT: Front Brake Inspection Procedure - Class Action Lawsuit Titled "Robert Lubitz et al. vs. DaimlerChrysler Corp". Case No.
NUMBER: 05-003-06 GROUP: Brakes DATE: July 21, 2006 This bulletin is supplied as technical information only and is not an authorization for repair. No part of this publication may be reproduced, stored
More information1999 Toyota RAV BRAKES Disc & Drum - Trucks & Vans
DESCRIPTION & OPERATION 1999-2000 BRAKES Disc & Drum - Trucks & Vans WARNING: For warnings and procedures regarding vehicles equipped with Anti-Lock Brake Systems (ABS), see appropriate ANTI-LOCK article.
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W120-22, W120-23 1964 1/2-69 MUSTANG Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS FX4 ELITE REAR DISC CONVERSION KITS WITH INTERNAL PARKING BRAKE A110-14, A111-25, A111-29 for FORD 8" & 9" REAR ENDS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KITS W156-6 & W156-7 1965-74 MOPAR B & E BODY Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationwww.clubsuprafrance.com CLUTCH 1996 Toyota Supra 1995-96 Clutch Supra DESCRIPTION The single, dry-type disc clutch uses a hydraulicallyoperated master cylinder with a clutch release cylinder mounted on
More informationBrake Pads. Front Brake Pad Removal. Rear Brake Pad Removal After bending the lockwasher tabs up, loosen the pad mounting bolts. BRAKES 11~9. A.
BRAKES 11~9 Rear Caliper Inspection 1. Boot 3. Brake Cam Assembly 2. Parking Brake Shaft A. Pad Mounting Bolts Loosen the torque link nuts after removing the clips. Remove the caliper mounting bolts. Take
More informationASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH DIAMETER SOLID ROTOR PINTO / MUSTANG II
ASSEMBLY INSTRUCTIONS FOR DYNALITE DRAG RACE FRONT HUB KIT WITH 0.75 DIAMETER SOLID ROTOR 97-978 PINTO / MUSTANG II (FIVE LUG CONFIGURATION ONLY)* PART NUMBER GROUP 0-03-B DISC BRAKES SHOULD ONLY BE INSTALLED
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS POWER FRONT DISC CONVERSION KIT A126-7 1963-66 CHEVY C10 PICKUP NON-POWER FRONT DISC CONVERSION KIT A126-8 1963-72 CHEVY C10 PICKUP Thank you for choosing STAINLESS STEEL BRAKES
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KITS SUM-BK1329-X, SUM-BK1329-99904, SUM-BK1330-X, SUM-BK1330-99904 CHRYSLER 8 3 /4", 9 3 /4" and 2-PIECE REAR AXLES Thank you for choosing SUMMIT RACING
More informationASSEMBLY INSTRUCTIONS
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT VENTED ROTOR TYPE (.36 OFFSET) MOPAR 8-3/ / DANA 60 FOR USE W/GREEN () NON-ADJUSTABLE BEARINGS W/SNAP RING PART NUMBER 0-7* WARNING
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A157 1991-2004 Dodge Dakota 2WD 1991-2002 Dodge Dakota 4WD 1998-2002 Dodge Durango Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS BIG ROTOR / CALIPER RELOCATION FRONT KITS SUM-BK1422, BK1423, BK1424 1999-2006 GM 1/2 Ton Trucks & SUVs Thank you for choosing SUMMIT RACING for your braking needs. Pleases take
More informationDRAIN BRAKE FLUID NOTICE:
REAR DISC OVERHAUL Overhaul the RH side by the same procedure as the LH side. 1. REMOVE REAR WHEEL 2. DRAIN FLUID Wash the brake fluid off immediately if it comes into contact with any painted surface.
More informationASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH DIAMETER VENTED ROTOR CAMARO/FIREBIRD (DISC SPINDLE)
ASSEMBLY INSTRUCTIONS FOR DYNALITE BIG BRAKE FRONT HUB KIT WITH.75 DIAMETER VENTED ROTOR 1979-1981 CAMARO/FIREBIRD (DISC SPINDLE) PART NUMBER GROUP -817-B DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A126-1 1973-87 CHEVROLET 1/2 TON 2WD Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to
More informationDESCRIPTION & OPERATION
2004 BRAKES Disc - TSX DESCRIPTION & OPERATION WARNING: DO NOT use air pressure or a dry brush to clean brake assemblies. Avoid breathing brake dust. Use OSHA-approved vacuum cleaner for cleaning and collecting
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC CONVERSION KIT A126-2 1988-98 C1500 2WD 10" REAR DRUM Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More information2003 Dodge Pickup R DRIVE AXLES' 'Axle Shafts - Front - Ram Pickup WD DRIVE AXLES
2002-04 DRIVE AXLES Axle Shafts - Front - Ram Pickup 1500 4WD DESCRIPTION Vehicles equipped with 4WD and C205F front axle assembly use equal length axle shaft system to deliver power from front differential
More informationASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER SOLID ROTOR (2.81 OFFSET) OLDS / PONTIAC
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH.9 DIAMETER SOLID ROTOR (.8 OFFSET) OLDS / PONTIAC PART NUMBER GROUP 0-6703 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED
More informationBIG BRAKE KIT FOR TJ, ZJ, XJ D44 & D30
BIG BRAKE KIT FOR TJ, ZJ, XJ D44 & D30 16 KIT PART NUMBER 41002010AA 17 KIT PART NUMBER 41002015AA Installation Guide (Updated 12/01/09) Page 1 of 11 PLEASE READ BEFORE YOU START IN ORDER TO INSTALL THIS
More informationThis file is available for free download at
This file is available for free download at http://www.iluvmyrx7.com This file is fully text-searchable select Edit and Find and type in what you re looking for. This file is intended more for online viewing
More informationINSTALLATION INSTRUCTION Rev A
INSTALLATION INSTRUCTION 88587 Rev A FOR RANCHO SUSPENSION SYSTEM RS6587B: 2009 DODGE RAM 1500 READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION IMPORTANT NOTES! WARNING:
More informationBrake System Diagnosis and Service
AUMT 1310 - Brake System Diagnosis and Brake System Inspection Brake System Diagnosis and Donald Jones Brookhaven College Road test Hydraulic system Leaks Fluid condition Disc brakes Rotors and pads Drum
More informationDISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE EXPERIENCED AND COMPETENT IN THE INSTALLATION AND MAINTENANCE OF DISC BRAKES READ ALL WARNINGS
ASSEMBLY INSTRUCTIONS FOR SUPERLITE BIG BRAKE FRONT HUB KIT WITH 1.90 DIAMETER VENTED ROTOR 197-199 CAMARO, DISC/DRUM SPINDLE 197-197 NOVA, DISC/DRUM SPINDLE 19-19 CHEVY II, DRUM SPINDLE WITH MODIFICATIONS
More informationTech Feature: Brake Job on Ford Edge
Tech Topics Tech Feature: Brake Job on Ford Edge By Andrew Markel email Editor, Brake & Front End Magazine August 20, 2010 The Ford Edge is an SUV based on a the CD3 platform. The brakes on these vehicles
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-3 1965-72 GM A-BODY 10 & 12 BOLT AXLES Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time
More informationASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH DIAMETER VENTED ROTOR (2.36 OFFSET) BIG BEARING FORD
ASSEMBLY INSTRUCTIONS FOR DYNALITE PRO SERIES REAR PARKING BRAKE KIT WITH 1.19 DIAMETER VENTED ROTOR (.36 OFFSET) BIG BEARING FORD PART NUMBER GROUP 10-7139 DISC BRAKES SHOULD ONLY BE INSTALLED BY SOMEONE
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS DISC BRAKE CONVERSION KITS A121-1, A121-2, A121-3, A121-4 1967-69 Ford & Mercury Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take
More informationINSTALLATION INSTRUCTION 88581
INSTALLATION INSTRUCTION 88581 FOR RANCHO SUSPENSION SYSTEM RS6581B: DODGE RAM READ ALL INSTRUCTIONS THOROUGHLY FROM START TO FINISH BEFORE BEGINNING INSTALLATION Rev C IMPORTANT NOTES! WARNING: This suspension
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A158 1994-97 Dodge Ram 1500 (2WD & 4WD) and REAR DISC BRAKE CONVERSION KIT A158-1 1998-01 Dodge Ram 1500 (2WD & 4WD) Thank you for choosing STAINLESS
More informationMOPAR RACE/STREET FRONT BRAKE KIT INSTRUCTIONS. FOR ANY QUESTIONS, PLEASE CALL M-F 8:00a.m.-8:00p.m. EST.
MOPAR RACE/STREET FRONT BRAKE KIT INSTRUCTIONS 1 AEROSPACE COMPONENTS 727.347.9915 You will need some items for best results when installing your Aerospace Brake kit. The following is recommended: At least
More information#05068C: Product Safety - Front Wheel Speed Sensor Corrosion - (Mar 6, 2008)
#05068C: Product Safety - Front Wheel Speed Sensor Corrosion - (Mar 6, 2008) Subject: 05068C -- FRONT WHEEL SPEED SENSOR CORROSION Models: 1999-2002 CHEVROLET SILVERADO 2000-2002 CHEVROLET TAHOE, SUBURBAN
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS REAR DISC BRAKE CONVERSION KIT A125-2 1955-70 FULL SIZE CHEVROLET Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases take the time to read
More informationIndicates a potential hazard that could result in death or injury. Indicates a potential hazard that could result in motorcycle damage.
FOREWORD This motorcycle has been designed and produced utilizing Suzuki s most modern technology. The finest product, however, cannot perform properly unless it is correctly assembled and serviced. This
More informationINSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125
INSTALLATION INSTRUCTIONS PERFORMANCE AT THE WHEELS KIT W125 1968-81 CAMARO & FIREBIRD 10 & 12 BOLT W/"C" CLIPS Thank you for choosing STAINLESS STEEL BRAKES CORPORATION for your braking needs. Pleases
More information