ManuFlo Catalogue

Transcription

1 ManuFlo Catalogue Effective from 6 th Aug /2018 Manu Electronics Pty Ltd UManuFlo Flow Measurement & Control Products Manufacturers and suppliers since 1965 UMANU ELECTRONICS PTY LTD 41 Carter Rd Brookvale Sydney NSW 2100 Australia Tel: , Fax: Web: sales@manuelectronics.com.au ABN: /4, v0.91

2 See for product data sheets. UTable Of Contents 1. FLOWMETERS MRP SERIES - RESETABLE INTEGRAL LCD COUNTER + RATE PADDLEWHEEL SCREWED INSERTION FLOWMETERS MRP20-T2 20mm LCD RESETABLE COUNTER CONCRETE TRUCK FLOWMETER (screwed insertion) SPARE PARTS for MRP20, MRPU4, MRPU5, MRPU6 (-F) (Screwed Insertion Flowmeters) MRT SERIES - INTEGRAL LCD RESETABLE TOTALISER (WITH FLOWRATE) DISPLAY PADDLEWHEEL SLIP INSERTION FLOWMETERS MRT20-T2 20mm LCD RESET COUNTER CONCRETE TRUCK FLOWMETER (New slip insertion) MRTU6 DUAL DISPLAY LCD RATE / RESETTABLE or GRAND TOTAL (or) For pipes sizes mm Ф RPFS - Rota Pulse (Paddlewheel) Pulse Flow Sensors (slip insertion) For pipes sizes mm Ф PIPE ADAPTER FITTINGS & ACCESSORIES for all MRTU & RPFS FLOWMETER slip insertion models SPARE PARTS for MRTU & RPFS series slip insertion flowmeters FRT303 REMOTE LARGE LCD DUAL FLOWRATE/RESET TOTAL & GRAND TOTALISER IP65 INDICATOR WITH OPTIONAL OUTPUTS ME5 REMOTE LCD FLOWRATE OR RESET TOTALISER IP65 INDICATOR (LARGE DIGITS) MES SERIES FLOWMETERS - NUTATING DISC, POSITIVE DISPLACEMENT - WIDELY USED FOR ADMIXTURES MES-P Pulse output flowmeters (25+ yrs chamber operating life)* MES-MR mechanical display flowmeter (with or without pulse output) MES-LCD6 flowmeter DUAL DISPLAY Resetable Total and Flowrate - widely used for Admixtures MES20-S / -S-T with Ryton MTL chamber / Teflon coated body for Low.PH-chemicals and petroleum liquids SPARE PARTS for MES series flowmeters PSM DOMESTIC WATER FLOWMETER COMPLIANCE WITH NMI R49-1 AUSTRALIAN STANDARDS AS PATTERN APPROVED CT5 DOMESTIC WATER APPROVED FLOWMETERS HIGH PULSE RATE FOR PRECISION DATA LOGGING FOR WATER STUDIES DATA LOGGERS S C HOT WATER FLOWMETERS, WITH OPTIONAL PULSE OUTPUT WP-D TURBINE WATER FLOWMETERS, MECHANICAL TOTAL, OPTIONAL PULSE OUTPUT PWMR Paddlewheel Mechanical Water Meters with Pulse Output MEHR Multi-jet and Turbine cold water mechanical totaliser flowmeter (optionally also with pulse output) TMW25 TURBINE LCD RESETTABLE PLASTIC FLOWMETERS (FOR WATER/UREA ONLY) A FM25 MECHANICAL RESETTABLE FUEL METERS (FOR DIESEL, KEROSENE, PETROL, OILS) B CR25 OVAL ROTOR POSITIVE DISPLACEMENT FLOWMETER (FOR CORROSIVE CHEMICALS ) IDEAL FOR NON-CONDUCTIVE FLUIDS C ME7 LCD TOTALISER AMM ADMIXTURE MINI MAG. COMPACT ADMIXTURE FLOWMETERS (SIZES MM) MM MINIMAG COMPACT ELECTROMAGNETIC FLOWMETERS WITH DISPLAY (SIZES MM) SMP BUDGET BATTERY-POWERED ELECTROMAGNETIC FLOWMETERS MFS MagMaster Electromagnetic Flowmeter with display and outputs * SPARE PARTS & REPAIR SERVICE * RMS ROSEMOUNT HIGH PRESSURE PROCESS ELECTROMAGNETIC (GROUT) FLOWMETERS (FM - HAZARDOUS APPROVAL) KMS SERIES. K-MAG ELECTROMAGNETIC FLOWMETERS KMS703 ELECTROMAGNETIC INTERNAL BATTERY POWERED FLANGED FLOWMETERS WITH S70 DISPLAY WITH PULSE OUTPUTS KMS501W ELECTROMAGNETIC WAFER FLOWMETERS WITH S50 DISPLAY & OUTPUTS (IDEAL FOR TRADEWASTE AND BORE WATER) KMS502F ELECTROMAGNETIC FLANGED FLOWMETERS WITH S50 DISPLAY & OUTPUTS (IDEAL FOR TRADEWASTE AND BORE WATER) KMS506-S ELECTROMAGNETIC FLOWMETERS FOR HYGEINIC USE WITH S50 OR S100 DISPLAY & OUTPUTS KMS101W ELECTROMAGNETIC WAFER FLOWMETERS WITH S100 DISPLAY & OUTPUTS (IDEAL AS RESETTABLE/BATCHING METER) KMS102/4F ELECTROMAGNETIC FLANGED FLOWMETERS WITH S100 DISPLAY AND OUTPUTS (IDEAL AS RESETTABLE/BATCHING METER) i

3 KMS302F ELECTROMAGNETIC FLANGED FLOWMETERS WITH S300 DISPLAY AND OUTPUTS (FOR GROUT, OXIDES AND SLURRIES) KMS305W ELECTROMAGNETIC WAFER FLOWMETERS WITH S300 DISPLAY & OUTPUT (FOR CORROSIVE CHEMICALS/ACIDS & SLURRIES) CONNECTION KITS FOR FLANGED OR WAFER-STYLE FLOWMETERS BATCH CONTROLLERS ME995 PRESET BATCH CONTROLLER SERIES ROTARY SWITCH KNOB SELECTOR MODELS ME3000 PRESET BATCH CONTROLLER KEYPAD MICROPROCESSOR MODEL BATCH CONTROLLER PLC INTERFACING AND OPTIONS BATCH CONTROLLER SPARES INTERFACE CARDS TO PLC, FOR BATCH CONTROLLERS WITH FLOWMETERS ME6008M BATCH MONITOR PRINTER DRIVER UNIT FIELD ENCLOSURES TO HOUSE ME995/ME3000 BATCH CONTROLLERS PLC/COMPUTER INTERFACE BATCH PRODUCTS ME2008/ME2000 MICROPROCESSOR SAFETY MANAGEMENT INTERFACE BATCHING CARD ME2008/ME2000 MICROPROCESSOR SAFETY MANAGEMENT INTERFACE BATCHING CARD (OPTIONS / SPARES) ME2008/ME2000 Expansion / Spares UIC FLOWMETER INTERFACE PULSE SCALER CARD SYSTEMS NOTE: A RANGE OF PRODUCTS FROM THIS CATALOGUE CAN BE MIXED AND MATCHED TO FORM SYSTEMS SLUMP STAND SYSTEMS ME6 BATCHROOM 6-CHANNEL TOTALISER DISPLAY WITH MASTER RESET + OUTPUTS FOR MULTIPLE SYSTEMS DOSING LOW FLOWRATES CHEMICALS SHOTCRETE ADMIXTURE FLOWMETERS GROUT / OXIDE / SLURRY FLOWMETERS (FOR MEASURING LIQUIDS UPTO 80% SOLIDS) CONCRETE PLANT ADMIX/WATER BATCH SYSTEMS CONCRETE BATCH PLANT ADMIX SYSTEM KIT TMP AUTO BATCHING CUSTODY TRANSFER TICKET PRINTER SYSTEM (USED PRIMARILY WITH ELECTROMAGNETIC FLOWMETERS) TMP-1 MANUAL BATCHING CUSTODY TRANSFER DOCKET PRINTER SYSTEM (SINGLE CHANNEL) PRESSURE MEASUREMENT SYSTEMS OPTIBAR - NEW PRESSURE SENSORS WITH ATEX, IECEX CERTIFICATES FILTERS, ELECTRICAL ACCESSORIES AND SOLENOID VALVES FILTERS. Y-STRAINER CARTRIDGE TYPE ELECTRICAL ACCESSORIES CONTACTORS, SIGNAL CABLE AND POWER SUPPLIES SOLENOID CONTROL VALVES - METAL PUMPS OPTIONAL CONNECTORS, GATE VALVES AND CHECK VALVES OTHER SERVICES - CALIBRATIONS, REPAIRS, TRAINING, DESIGN DELIVERY TERMS AND CONDITIONS OF SALE QUOTE REQUEST FORMS See for product data sheets. ii

4 1. FLOWMETERS 1.1 MRP Series - Resetable integral LCD counter + rate paddlewheel screwed insertion flowmeters MRP20-T2 20mm LCD RESETABLE COUNTER CONCRETE TRUCK FLOWMETER (screwed insertion) Custom designed and built primarily for use on Concrete Transit Mixers (agitators). Display Head has robust Gunmetal housing for the harshest environments. Hinged lid protects LCD from sunlight. Robust Tempered Glass window Unaffected by water hammer, compressed air, mild frozen or light recycled water. No damage to meter if run above its maximum flowrate. shows total in Litres.,closing lid resets total. NEW LARGER 4-digit LCD (18mm high) counts in LITRES or to 1 dec.pt. Accuracy: ± 2% (at m/s flow velocity), calibration certificate issued. Flowrange: 8-90 Litres/min Durable marine-grade S/S paddlewheel rotor. Internal 3.6 v Lithium Battery (10+ year life). Sealed IP65 digital display compartment. Access for re-calibration Repeatability +/-0.5%, Temp to 55 ºC Pressure to 2000Kpa Optional pulse output via M12 plug-set 19mm ID bore, with gun-metal flowtube ¾ BSP (male) threaded connection ends. Max. Operating Pressure: 2000 kpa Size: 270 L x 105 H x 85 W (mm) NEW: Version v.4 PCB with RFID/NFC Communication Re-calibration feature. MRP20-T2 INDUSTRIAL GRADE BUILT TO LAST Flowrange* UOrder CodeU UDescriptionU Litres per min MRP20-T2 20mm digital LCD Litres resetable counter flowmeter to 50ºC 8-90 special purpose meters for concrete trucks (and other applications) Gunmetal flowtube with ¾ BSP male threaded pipe connection ends With new V.4 RFID/NFC re-calibration feature. OPTIONS -P Pulse output option (1 Litre/1 pulse), with M12 IP67 plug set, 5mtr cable 100 Hz maximum, 5 ms fixed pulsewidth. -D1 Display counts to 0.1 Litres (Note: pulse option is also to 0.1 litre) NFC.A Re-calibration software package install on Andriod or Laptop * The stated flowrange is for 2% accuracy. Measures outside this flowrange, t reduced accuracy. 4-digit resetable LCD shows Litres New.v4 PCB -P Pulse Option See for product data sheets. 1

5 1.1.2 SPARE PARTS for MRP20, MRPU4, MRPU5, MRPU6 (-F) (Screwed Insertion Flowmeters) UProduct CodeU MRPU4 UDescriptionU GunMetal Display head (reset total LCD) c/-hex.nut Calibrated to nominated pipe diameters 25mm to 50mm or pre-fitted and calibrated to below pipe fittings; -P Pulse output 1/1 ltr via M12 Ip67 plug-set 5mtr lead GAL25M 25mm 1 bsp-f galvanised tee adaptor fitted GAL32M 32mm 1 ¼ bsp-f galvanised tee adaptor fitted GAL40M 40mm 1 ½ bsp-f galvanised tee adaptor fitted GAL50M 50mm 2 bsp-f galvanised tee adaptor fitted MRP20-DH SPARE PARTS BELOW:- Complete Display head only (New 4 digit LCD) For 20mm only -P Pulse output 1/1 ltr via M12 Ip67 plug-set 5mtr lead MRP5-GLASS Glass window ( in Litres for total old PCB) Until stock is sold out Until stock is sold out MRPU4-GAL50M Flowmeter MRP4/6-GLASS MRP-PCB PC-MRP-5 PC-MRP-15 PW-N PWAH LB LM MRP-MAG Glass window (in Litres) Larger view new PCB) MRPU5, MRPU4, MRPU6 and -F PCB.v4 (Note: will also require new glass to suit) M12 IP67 5-mtrs plug-in PULSE 2core cable 15-mtrs Paddlewheel with new bush high speed design Tungsten carbide axle Lithium Battery 3.6v (6-10 year life) Lid with magnet and pin Magnet PW-N wheel pictured on MRP unit. Below: Conversion of MRP to MRT using BSPB adaptor nipple T2 Gunmetal flowtube for MRP20-T2 MRPU6-SP Special Smart Pipe unit KL.1DP, LPS.1DP, 0.1KL/P, m12 pulse lead-m (for USAG/Skilltec -only) NOTE: All MRP models will be slowly superseded by the new MRT models (Spare parts and full repairs ongoing) See for product data sheets. 2

6 1.2 MRT Series - Integral LCD Resetable Totaliser (with flowrate) display paddlewheel slip insertion flowmeters MRT20-T2 20mm LCD RESET COUNTER CONCRETE TRUCK FLOWMETER (New slip insertion) Custom designed and built primarily for use on Concrete Transit Mixers (agitators). NEW FEATURES:- Robust ABS-UV IP65 Display housing with 3M film scratch protection NEW Dual Hinged robust lid protects LCD from sunlight, with magnet secure function. NEW slip insertion design allows simple removal from pipeline if cleaning rotor NEW Easier Access for re-calibration with User friendly smart 1 point re-calibration function self calculation for a new k-factor. NEW Optional External re-calibrate via Portable Device with RFID / NFC com. NEW large display: 4 digit LCD Reset Total in LITRES. (optionally with 1 decimal place) Flowrange: 8-80 Litres/min Accuracy: ± 2% (at m/s flow velocity), Repeatability +/-0.5%, Temp to 55 ºC. Calibration certificate issued to NMI-NSS1671. Durable marine-grade S/S paddlewheel rotor. Internal 3.6 v Lithium Battery (10+ year life). Pressure to 1100Kpa Unaffected by water hammer, compressed air, mild frozen or light recycled water. No damage if run above max. flowrate. Optional pulse output via M12 plug-set 18mm ID bore, with gun-metal flowtube with slip insertion keyway adaptor ¾ BSP (male) threaded connection ends. Size: 270 L x 105 H x 90 W (mm) LIVE pulse option even when lid is closed. NEW! Larger 4 digit display UFlowrange Order Code Description Litres/min +/- 2% MRT20-T2 20mm digital LCD Litres resetable counter +rate flowmeter to 50ºC 8-90 special purpose meters for concrete trucks. Gunmetal flowtube with ¾ BSP male threaded pipe connection ends with slip insertion BSP keyway locator with secure screw cap. OPTIONS -P Pulse output option (1 Litre/1 pulse), with M12 IP67 plug set, 5mtr cable 100 Hz maximum, 5 ms fixed pulsewidth metre M12 cable lead (in lieu of 5 mtrs) -D1 Display Total in LITRES to 0.1 increments. NOTE: Pulse output option (if ordered) then outputs 0.1 Litre/1 pulse. * The stated flowrange is for 2% accuracy. Measures outside this flowrange, but at reduced accuracy. NFC.A Re-calibration software package install on Andriod or to Laptop via USB wand M12- pulse output M12 plug lead Refer to datasheet for more options. See for product data sheets. 3

7 g MRTU6 DUAL DISPLAY LCD RATE / RESETTABLE or GRAND TOTAL (or) For pipes sizes mm Ф MRTU4 LARGER Display resettable Total or Rate display INTEGRAL FLOWMETERS FEATURES:- 6 digit LCD resettable or non-reset totaliser (10mm high), with 5 digit flowrate OR 4 digit LARGE LCD with total or flowrate Total in Litres or optional KiloLitres Flowrate in LPM or optional LPS Easy reset of total via flip top lid.. ± 2.5% accuracy, at m/s flow velocity Repeatability: ± 1.0% Internal 3.6 v Lithium Battery (8-10+ year life). Max. Operating Temp: 55 ºC Max. Operating Pressure: 1100 kpa With simple installation pipe fittings /adapters. For pipe diameters from 15 to 500 mm Optional pulse output, via M12 IP67 plugset NEW FEATURES:- Robust ABS-UV IP65 Display housing with 3M durable cover protection Dual Hinged robust lid protects LCD from sunlight, with magnet secure function. Slip insertion sensor design allows simple removal from pipeline if cleaning rotor NEW Easier Access for re-calibration and User friendly smart 1 point re-calibration NEW Optional External re-calibrate via Portable Device NFC calibration software. NEW Dual display: Rate + Reset Total 6-digit LCD (12mm high) counts in LITRES. New 4 digit LARGER LCD display option with Resettable total or Flowrate (18mm H.) UFlowrangeU UOrder CodeU UDescriptionU ULitres/minU MRTU6 MRTU4 NEW! MRTU6: Ideal in Irrigation and many other general water measurement and monitoring applications. SLIP INSERTION PADDLEWHEEL Pictured in and out of flowpipe Examples; MRTU6-LS MRTU6 LCD dual display Flowrate LPM / 6 dgit Totaliser LTRS (resettable) with integral mounted slip insertion multi-pipe-size adaptable rotor sensor as per selected fitting flowmeter. IP65 ABS-thermal housing. For pipe sizes <110mm MRTU4 LCD Larger 4 digit display (resettable) TOTALISER SC110 Saddleclamp OPTIONS: (Refer to datasheet for extra additional options) -LS Long stem brass sensor probe upgrade for larger pipe sizes (>125mm) (for use with adaptor pipe fittings with the LS suffix code) -P Pulse output option (1/1 standard), with M12 IP67 plug set and 5-metre lead. 1/10/100/1000 Litres / 1 Pulse (scaleable); 100 Hz maximum, 5 ms pulse width. -KL Total in KiloLitres -DP1 1 decimal place -P10 10 litres/pls. -NRT Running total, No reset of total (internal secret reset only) -LPS FlowRate Litres per second -DP1 1 decimal place MRTU4-F 4 digit large LCD Flowrate only display LPS or LPM (no pulse output option) NFC.A Re-calibration software package install on Andriod or Laptop -P1 Pulse Plug BSPSS BSPB-LS S/S316 St. Stem Brass Long Stem (110mm Ф <) (125mm Ф >) SELECT FROM: MRTU / RPFS PIPE ADAPTOR FITTING RANGE for adaption to various pipelines types & sizes from 20 to 500mm (See pages 9 10) NOTE: Pre-fitted to selected pipe and calibrated to NMI-NSS1671 on wet-test flowrig to 100mm Ф See for product data sheets. 4

8 1.2.3 RPFS - Rota Pulse (Paddlewheel) Pulse Flow Sensors (slip insertion) For pipes sizes mm Ф Paddlewheel insertion type flow sensor. General purpose, value flow sensor for many applications involving clean liquids (not suitable where liquid contains stringy/fibrous matter). Simple installation & maintenance. Durable Marine-grade S/S paddlewheel rotor without magnets, improved performance at low flowrates. Australian made since For pipe adapter fittings, see following pages. ± 2.5% velocity range 0.5 to 8.5 m/sec. ± 1.5% over linear range 0.7 to 7.0 m/sec (RPFS-P starts to measure from 0.3 m/sec). Repeatability ± 1.0%. Large range of pipe adapter fittings in sizes mm (for various pipe diameters optionally use adapter fittings BSPB, BSPSS or BSPB-LS for larger pipe diameters). 50 C or 120 C temperature models. Suitable for WATER liquids of Specific Gravity 1.0 For Spare Parts, see following pages. Order Code RPFS-P RPFS-H Description Rota Pulse Flow Sensor, NPN pulse output, 50ºC (M12 Plug-in 5m lead +lockcap) For use with Batch Controllers/PLCs e.g. ManuFlo ME995-7., UIC Delrin body, IP VDC powered. To 1200 kpa (175 psi). Rota Pulse Flow Sensor, NPN pulse output, Hi-Temp (2m lead + brass lockcap) Brass body, For hot water up to 120ºC. To 2000 kpa (300 psi).ip VDC pwr. See for product data sheets. 5 RPFS-P Flowrange* Litres/min as per fitting as per fitting RPFS-H-P As above brass body high pressure, temp to 50ºC, (2m lead + brass lockcap) as per fitting RPFS-H-P RPFS-L Rota Pulse Flow Sensor, inductive coil pulse o/p, 120 C (2m lead + lockcap) IP65. To 1034 kpa (150 psi). For use with battery-operated indicators e.g. FRT303-B, ME5-T-B, ME5-F-B as per fitting RPFS-L-O Rota Pulse Flow Sensor, inductive coil pulse o/p, 50 C (M12-2m lead + lockcap) as per fitting Inbuilt-op.amp. for datalogger application 3-24VDC pwr. (ideal for battery pwr only apps.) RPFS-H-LS Rota Pulse Flow Sensor, LONG STEM for pipes 120mm. as per fitting NPN pulse output, (2m lead + lockcap). IP VDC powered. For use with liquids up to 50ºC. To 2000 kpa (300 psi). RPFS-L-LS Rota Pulse Flow Sensor, LONG STEM for pipes 120mm. as per fitting inductive coil pulse o/p, 120 C (2m lead + lockcap). IP65. To 2000 kpa (300 psi). For use with battery-operated indicators e.g. FRT303-B, ME5-B etc For use with any Remote Batch Controllers Display Indicators: ME995-7, ME3000, FRT303, ME5 or with practically any logic pulse input device Adapt into pipes using ManuFlo s various pipe adaptor options Locking Cap included RPFS-P RPFS-H RPFS-L RPFS-O RPFS-H-LS RPFS-L-LS NEW : Long stem version for adapting to larger pipe diametersmatch with -LS pipe adaptors

9 . For PIPE ADAPTER FITTINGS & ACCESSORIES for all MRTU & RPFS FLOWMETER slip insertion models Order Code Description White PVC F-Slip-Socket Tees with glued grey PVC adaptor keyway insert For PN6, PN12, PN18 Series 1 PVC pipe sections Pipe OD mm Approx PPL (1) Flowrange Litres/Min (2) PVC20 20mm ( ¾") PVC Class18, Cat.19 high pressure pipe slip(f) adapter fitting to 1100 kpa PVC25 25mm (1 ) PVC32 32mm (1¼") PVC40 40mm (1½") PVC50 50mm (2" ) PVC65 65mm (2½") PVC80 80mm (3" ) PVC mm (4" ) Locking Cap Included PVC50 PVC80 Galvanised Malleable Cast Iron parallel thread BSP(f) pipe tees with Brass adaptor keyway insert use with any BSP(m) connectable pipe sections or fittings. GAL25 25mm (1" ) Galvanised Iron Adaptor fitting (female BSP threaded ends), to 1600 kpa GAL32 32mm (1¼ ) " " " " " " GAL40 40mm (1½") " " " " " " GAL50 50mm (2" ) " " " " " " GAL25-T2 25mm (1 ) BSP-m. Gal. pipe thread ends 500mm long, fit to SS310 pipe tee keyway adaptor fitiing (Commonly used on slumpstands in concrete premix batch plants) GAL32-T2 32mm (1 ¼ ) BSP-m. pipe threaded ends 500mm long, fitted to Gal. pipe tee keyway adaptor fitting Pictured MRTU6-P-GAL50 GAL40-T2 40mm (1 ½ ) BSP-m. pipe threaded ends 600mm long, fitted to Gal. pipe tee keyway adaptor fitting GAL50-T2 50mm (2 ) BSP-m. pipe threaded ends 600mm long, fitted to Gal. pipe tee keyway adaptor fitting GAL80-T2 80mm (3 ) BSP (male) tapered threaded ends. BSPB keyway welded into 600mm long Gal. pipe GAL100-T2 100mm (4 ) BSP (male) tapered threaded ends GAL100-T2 Higher pressure Gal. fittings or flanged ends ansi-150 or table-d on request. S/S-316 parallel thread BSP(f) pipe tee fittings with BSP-S/S keyway insert. SS25 25mm (1 ) Stainless Steel 316 adaptor tee fitting with keyway (BSP-f) threaded ends SS32 32mm (1¼ ) " " " " " " SS40 40mm (1½") " " " " " " SS50 50mm (2" ) " " " " " " SST-xxx Stainless-Steel-316 custom flowtubes (flanged or threaded ends) built to request 25-50mm sizes per dia. Diameter? SS25 Fabricated SS080 See for product data sheets. 6

10 PIPE ADAPTER FITTINGS & ACCESSORIES for all MRTU & RPFS FLOWMETER slip insertion models (continued) Order Code Description Tapping Band SADDLE CLAMPS (pipe hole cutout size is 32mm) 4N Tapping saddle bands Used on series 1 PVC pipe AS/NZ-4793 glass re-enforced Beige color plastic with NBR gasket E-lip seal (requires low bolt torque, 316 S/S bolts/nuts (x2). Pipe OD mm Pulses Litre (1) Flowrange Litres/Min (2) PVC40SC 40mm (1½") Saddleclamp adapter with keyway for PVC series 1 pressure pipes to PN Saddle fitted to PVC50SC 50mm (2 ) pipe PVC80SC 80mm (3 ) PVC100SC 100mm (4 ) PVC150SC-LS 150mm (6 ) Saddleclamp keyway adapter for PVC (series 1) pressure pipes PN16 (Long Stem) PVC195SC-LS 195mm (8 ) (Long Stem) PVC200SC-LS 200mm (8 ) (Long Stem) PVC80SC PVC300SC-LS 300mm (12 ) (Long Stem) N Tapping saddles Used for Ductile Iron, AC & series 2 PVC pipe glass re-enforced Blue color plastic with NBR gasket E-lip seal (requires low bolt torque, 316 S/S bolts/nuts.x2) PVC100SC-2 100mm (4 ) Saddleclamp keyway adapter for PVC series 2 pressure pipes to 1500 kpa PVC150SC-2-LS 150mm (6 ) Saddleclamp adapter for PVC series 2 pressure pipes to 1500 kpa. (Long Stem) PVC100SC-2 PVC200SC-2-LS 200mm (8 ) (Long Stem) PVC300SC-2-LS 300mm (12 ) (Long Stem) N Tapping bands Used for Metric Irrigation PE pipe AS4130 glass re-enforced Black color plastic with NBR gasket E-lip seal (requires low bolt torque, 316 S/S bolts/nuts.x2) SCPE63 63mm Saddle clamp (metric PE pipe) adapter with keyway insert polypropylene pipe sections SCPE90 90mm SCPE mm PVC110SC-2 SCPE125-LS 125mm (Long Stem) SCPE160-LS 160mm (Long Stem) SCPE180-LS 180mm (Long Stem) SCPE225-LS 225mm (Long Stem) SCPE300-LS 300mm (Long Stem) Special Saddles available on request including DR gunmetal types for DI, CI and AC pipes. Pipes sizes from 58mm and larger 375, 450 & 600mm. - POA See for product data sheets. 7

11 . For PIPE ADAPTER FITTINGS & ACCESSORIES for all MRTU & RPFS FLOWMETER slip insertion models (continued). Order Code Description Tapping Band SADDLE CLAMPS -(pipe hole cutout size is 32mm) Pipe OD mm Pulses/ Litre (1) Flowrange Litres/Min (2) Tapping saddles suitable for irrigation PE pipes Polyprop Blue or Black color with NBR O-ring gasket (304 S/S bolts/nuts x4). SC40 40mm Saddle clamp (metric) adapter with keyway insert for black rural polyprop pipes SC50 50mm SC63 63mm SC75 75mm SC90 90mm SC mm SC110 SC125-LS 125mm Saddle clamp (metric) adapter for black rural polyprop pipes. Long Stem Only SC140-LS 140mm Long Stem Only SC160-LS 160mm Long Stem Only SC200-LS 200mm Long Stem Only SC225-LS 220mm Long Stem Only SC250-LS 250mm Long Stem Only SC280-LS 280mm Long Stem Only SC315-LS 315mm Long Stem Only Tapping saddles suitable for irrigation PVC pipes Polyprop Blue or Black color with NBR O-ring gasket (304 S/S bolts/nuts x4). SC50 40mm Saddle clamp (metric) adapter with keyway insert for black rural polyprop pipes SC60 50mm SC75 65mm SC75 SC90 80mm SC mm SC140-LS 125mm Saddle clamp (metric) adapter for black rural polyprop pipes. Long Stem Only SC160-LS 150mm Long Stem Only Inside view SC225-LS 200mm Long Stem Only SC250-LS 225mm Long Stem Only SC280-LS 250mm Long Stem Only SC315-LS 300mm Long Stem Only of saddle clamp with Adaptor insert & gasket. Gunmetal parallel thread BSP(m/f) pipe tees with Brass adaptor keyway insert use with any BSP(m/f) connectable pipe sections or fittings. B20-T2 20mm (3/4 ) Brass adapter Tee fitting with keyway (BSP-m threaded ends), 2000 kpa B20-T2 B25 25mm ( 1 ) Brass adapter Tee fitting with keyway (BSP-f threaded ends), 2000 kpa (1) The stated Pulses Per Litre value is nominal only, as the value is according to actual pipe I.D.. (2) The stated flowrange is for 2.5% accuracy. Can measure outside this flowrange, but at reduced accuracy. See for product data sheets. 8

12 PIPE ADAPTER FITTINGS & ACCESSORIES for all MRTU6 & RPFS FLOWMETER slip insertion models (continued) Order Code Description Pulses/ Litre (3) Price Discount Flowrange Litres/Min (1) Adapter sockets with BSP(m) keyway locators for adapting to any 1 BSP-f (25mm) threaded entry for fitting to most pipes sizes & types (screwed into sockets, tapping bands or welded to pipes) ** DO IT YOURSELF OPTION ** Depends Pipe I.D. BSPB Short Stem 25mm (1") BSP-m Brass Adaptor keyway nipple pipe fitting (incl. 1" lock nut) to 110mm pipes I.D. (Note 2) BSPB BSPSS Short Stem 25mm (1") BSP-m S/S-316 Adaptor keyway nipple pipe fitting (incl. 1" lock nut) to 110mm pipes I.D. (Note 2) BSPSS BSPB-LS Long Stem 1 BSP-m Brass Adapter nipple with locating key & locknut, for larger pipe sizes 125mm>. I.D. (Note 2) BSOC Brass socket (Adapter nipple screws into socket, which is welded to pipes. For mm Ø pipes). BSPB-LS APPLICATION NOTES:- All adaptor fittings are prefitted with ManuFlo patented Keyway insert adaptor and postioned at correct depth for capture of flows for the given pipe diameter to suit the MRT/RPFS insertion flowmeter range. For Manuflo to inhouse calibrate the MRT flowmeter or provide PPL for RPFS, then whilst ordering provide the internal diameter (I.D) of the pipe. NOTE: Sizes 80mmΦ & above incur a surcharge if requiring a NMI-NSS1671 calibration on the ManuFlo Flow-rig. PVC GAL SS PVC-SC / SC2 SCPE / SC Saddle Clamps PVC slip keyway adaptor tees used with PVC-U pressure pipes pipes are glued into the adaptor tees onsite. All MRP/MRT units are calibrated to PN12 PVC pipe diameters upto 100mm. GAL galvanised iron adaptor keyway tees have BSP threaded connections ideal for use with galvanised pipe sections, also suitable for any form of pipe that can be adapted to the tee of similar size or larger. SS 316 stainless steel adaptor keyway tees pipe connection options as above. A range of Saddleclamp adaptor fittings are prefitted with ManuFlo patented Keyway adaptor insert to capture pipe flows. To select the correct saddle size check the OD of the pipe that the saddle is to be fitted to. To fit saddles, you must cut hole size diameter of 32mm, the adaptor nipple then drops into pipe cutout and should sit approx. 10mm past the ID curvature of the pipe. (DO NOT lose seal gasket, overtighten bolts or fit on the underside of pipe). Formula PPL for ManuFlo paddlewheel flowmeters (Models: RPFS, MRP, MRT) Pulses Per Litre for a given pipe diameter Constant = 46,512 (pipe I.D. in mm)2 Example:- Pulses Per Litre for 200 mm I.D. pipe Therefore 46,512 (200)2 = 46,512 40,000 = 1.2 Pulses/Litre (this figure is then computed into the K-factor) Shown: FRT303-B Indicator, RPFS-L flowsensor, SC110 pipe adapter Portable battery-powered option. Cable length can be up to 100 metres. Pulse output for dataloggers See for product data sheets. 9

13 1.2.5 SPARE PARTS for MRTU & RPFS series slip insertion flowmeters Order Code Description BLN 25mm (1") Brass lock nut (Skinny) BLN BS020 Neoprene 'O' Ring BS020 LC LC-B PW PW-N Locking Cap (PE) Locking Cap (Brass for higher pressures) Spare RPFS/MRP/MRT paddlewheel (Marine Grade Alloy) with dual delrin bushes. Spare Paddlewheel with enhanced single black bush design for over flow speed applications LC PWAH Spare Axle / Shaft (non-wear tungsten carbide) PWAH PC-RPFSP Spare M12 IP67 5-metre plug-in 3core cable for RPFS-P. PC PC-RPFSP-15 As above but 15-metre lead SLC Sealer Lock Cap - for sealing adaptor fittings SLC MRT-TC MRT-C MRT-CU4 MRT-CU6 FT-MRT20 MRT20-PCB MRTU6-PCB LB MRT-MAG Top cover complete with protective film and cover lid Protective 3M film for MRT20 Protective 3M film for MRTU4 Protective 3M film for MRTU6 Spare new MRT20 Gunmetal flowtube ¾ bsp-m MRTU4 circuit board (replacement) MRTU6 circuit board (replacement) Lithium Battery 3.6v (8-10+ year life) Magnet MRT-TC PCB MRTU6-SP MRT-SMARTPIPE Complete display head c/w pulse for UASG/Skillec only See for product data sheets. 10

14 1.3.1 FRT303 REMOTE LARGE LCD Dual Flowrate/Reset Total & Grand Totaliser IP65 Indicator with optional outputs Order Code FRT303-B FRT303-B-P FRT303-D FRT303-D-P FRT303-D-E FRT303-A-P FRT303-A-E FRT303-A-TW Description (All programmable units, 2Khz input for any flowmeter, Reed, NPN, Coil) LCD 6d flowrate, 7d reset total & grand totaliser indicator. IP65 enclosure. Internal battery powered. as for FRT303-B above, but includes Pulse Output option. LCD flowrate, reset total & grand totaliser indicator. IP65 enclosure. External 5-30VDC powered. as for FRT303-D above, but includes Pulse Output option as for FRT303-D-P above, but includes Hi/Lo setpoints, Pulse & 4-20mA isolated output options. LCD flowrate, reset total & grand totaliser indicator. IP65 enclosure. 240vac powered. as for FRT303-A-P above, but includes Hi/Lo setpoints, Pulse & 4-20mA isolated output options. as for FRT303-A-E above, but includes Sydney Water 6pin MIL-spec SAMPLER plug. Options -SSB Stainless Steel outer enclosure. Hinged lid. Lockable.(to house and protect FRT303) FRT303-B FRT303 Spares LC-Display $165, Upper PCB $395, Lower PCB $395, Lid/Cover set $145, Housing $ 45, Bat.3.6v $ ME5 REMOTE LCD Flowrate or Reset Totaliser IP65 Indicator (Large digits) Order Code ME5-F-B ME5-F-D ME5-F-A Description LCD 5 digit Flowrate indicator. IP65 enclosure. Internal battery pwr. (for reed & coil flowmeters only) LCD 5 digit Flowrate indicator. IP65 enclosure. Ext 5-30VDC powered. (as above) LCD 5 digit Flowrate indicator. IP65 enclosure. 240vac powered. ME5-T-B LCD 5 digit reset Totaliser indicator, IP65 enclosure. Internal battery. (for reed & coil flowmeters only) ME5-T-B-P LCD 5 digit reset Totaliser indicator, with pulse output. IP65 enclosure. Internal battery. (as above) ME5-T-D LCD 5 digit reset Totaliser indicator, with pulse output. IP65 enclosure. Ext 5-30VDC pwr. ME5-T-A LCD 5 digit reset Totaliser indicator, with pulse output. IP65 enclosure. 240vac pwr. -IR option: Internal Reset. Total is reset via internal pushbutton instead of the round button on the face. ME5-T-B-0-L ME5-F FLOWRATE LCD Indicator Order Codes ME5-T TOTALISER LCD Indicator Order Codes Nominate at time of order: Mls, Litres, KL or ML per Sec., Min., or Hours. Nominate at time of order: Mls, Litres, KL or ML. with 0, 1 or 2 decimal places ME6 REMOTE LCD Resettable or Running Totaliser Indicator (Small digits). Order Code ME6 Description (1 pulse 1 count input only 20Hz max. input -not scalable e.g.) LCD 6 digit reset Totaliser indicator, IP54 panel mount, Internal battery. (for contact closure inputs)... -MB Mounted on wall mount box ( with cable gland entry for flowmeter pulse wire ) Ideal for contact closure flowmeters e.g. MEH, PWM, WP. MRP/MRT P pulse output, truck cabins etc Note: If flowmeter is 10ltrs/p output then each count on LCD display is LITRES x10 FRT303 / ME5: For use with RPFS range of slip insertion paddlewheel flowmeters and other pulse output flowmeters to suit fluid applications. See for product data sheets. 11

15 1.4 MES Series flowmeters - nutating disc, positive displacement - widely used for Admixtures MES-P Pulse output flowmeters (25+ yrs chamber operating life)* Ideal for Admixture Batching applications. MES20 has exclusive 1 millilitre / 1 pulse output. Measures liquids to Specific Gravity 1.4 Accuracy unaffected by variations in S.G s. Nutating disc measuring chamber. Small Impurities can pass through measuring chamber without jamming. Low hydraulic thrust minimises wear. IP64 rated, with 25yrs+ life Comprehensive Spare Parts. No more vibration issues Improved body/chamber operates to 83 LPM. NEW Digital pulse with 1, 10, 20, 50, 100 or Standard 1000 pulses per litres for all sizes. With smart technology bi-directional pulse. Operates from +4 to 40VDC Contact Closure switch pulse output option (-R). Accuracy: ± 1.5% (full scale flowrange) Repeatability: ± 0.2% Supply current: 5 to 25mA Prop to supply voltage Maximum working pressure: 1160 kpa Maximum liquid temperature: 50 C Connection: mm : threaded BSP (male) 40 mm : flanged BSP (female) NEW Vibration Free Digital Smart Pulse Order Code Description Flowrange# Transistor Pulse Output 5-25VDC Pulses per Litre Litres/min MES20 20mm digtal pulse output flowmeter, threaded ¾ BSP(m) ends. ( 1000 ppl ) MES20-N 20mm NEW compact low profile body & chamber version, ¾ BSP(m) ends ( 1000 ppl ) * Positive displacement high accuracy measurement MES25 25mm NEW digital pulse output flowmeter, threaded 1 BSP(m) ends ( 555 ppl ) MES32 32mm, threaded 1¼ BSP(m) ends ( 261 ppl ) MES40 40mm, flanged 1½ BSP(f) ends ( 116 ppl ) NOTE: All flowmeters now optionally with 1, 10,20, 50, 100 pulses/litre output (with new vibration free programmable digital bi-directional pulse & smart pulse division factors) (Must nominate at time of ordering e.g. MES = 25mm 1000ppl) MES20 MES20-N Contact Closure Pulse Output,switches upto 100mA MES20N-R 20mm Reed Switch pulse output flowmeter, threaded ¾ BSP(m)ends ( 61 ppl ) MES25R 25mm Reed Switch pulse output flowmeter, threaded 1 BSP(m) ends ( 34 ppl ) MES32R 32mm, threaded 1¼ BSP(m) ends ( 16 ppl ) MES40R 40mm, flanged 1½ BSP(f) ends ( 7.2 ppl ) Options for MES flowmeters -T Teflon-lined body. Add suffix to any 20mm MES-type flowmeter order code. MES20R CB Magnet Barrel Union connectors also available. # The flowrange is for 1.5% accuracy. Can measure outside this flowrange, but at reduced accuracy; Flowrange is for water. For Admix flowrange, divide water flowrate by the Admix sg. At ±5% accuracy, MES flowmeters can measure down to: 20mm: 0.5 Litres/min; 25mm: 1.0 L/m; 32mm: 1.5 L/m; 40mm: 2.8 L/m; *with water and light chemicals. See for product data sheets. 12

16 1.4.2 MES-MR mechanical display flowmeter (with or without pulse output) Non-resetable mechanical display reads in M 3 (down to 1 Litre). ideal for precision data logging and batching, with mechanical display and Reed pulse o/p. Measures liquids to Specific Gravity 1.4 Nutating disc P.D. measuring chamber. Small Impurities can pass through measuring chamber without jamming. Low hydraulic thrust minimises wear. Comprehensive Spare Parts. Suitable for Water Studies. Accuracy: ± 1.5%, Repeatability: ± 0.2% IP65 rated Reed contact closure switches upto 30 VDC and 100mA. Via 1.5mtr cable lead Maximum working pressure: 1160 kpa Maximum liquid temperature: 50 C Connection: mm : threaded BSP (male) 40mm : flanged BSP (female) Order Code Description Flowrange# Contact Switched Pulse Output, and mechanical non-resetable total display Pulses per Litre Litres/min MES20N-MR 20mm NEW compact version flowmeter, Reed Switch & mechanical Total, threaded ¾ BSP(m) ends (with Ceramic-Barium magnet with thermo-plastic shroud) ( 60.6 ppl ) MES25MR 25mm, Contact Closure & mechanical Total, threaded 1 BSP (m) ends ( 34 ppl ) MES32MR 32mm,, threaded 1¼ BSP (m) ends ( 16 ppl ) MES40MR 40mm,, flanged 1½ BSP (f) ends ( 7.2 ppl ) Optional -P Pulse output via M12 IP67 socket, and plug with 5 metres cable, in lieu of fixed cable. MES25MR Mechanical non-resetable total display (no pulse output) MES20N-M 20mm NEW compact version flowmeter, mechanical non-resetabletotal, threaded ¾ BSP(m) ends (with Ceramic magnet with thermo-plastic shroud) MES25M 25mm flowmeter mechanical non-resetabletotal, threaded 1 BSP (m) ends MES32M 32mm, threaded 1¼ BSP (m) ends MES40M 40mm, flanged 1½ BSP (f) ends T Teflon-lined body. Add suffix to any 20mm MES-type flowmeter order code. # The flowrange is for 1.5% accuracy. Can measure outside this flowrange, but at reduced accuracy; Flowrange is for water. For Admix flowrange, divide water flowrate by the Admix sg. (1) At ±5% accuracy, MES flowmeters can measure down to: 20mm: 0.5 Litres/min; 25mm: 1.0 L/m; 32mm: 1.5 L/m; 40mm: 2.8 L/m; See for product data sheets. 13

17 1.4.3 MES-LCD6 flowmeter DUAL DISPLAY Resetable Total and Flowrate - widely used for Admixtures Ideal for Precision Batching applications. Closing the lid resets the display total. Measures liquids to Specific Gravity 1.4 Nutating disc P.D. measuring chamber. Small Impurities can pass through measuring chamber without jamming. Low hydraulic thrust minimises wear. Internal Lithium battery (10+ year battery life) Accuracy: ± 1.5% full scale flowrange Repeatability: ± 0.2% Maximum working pressure: 1160 kpa Maximum liquid temperature: 50 C Connection: 20, 25 & 32 mm : threaded BSP(m) 40 mm : flanged BSP(f) NEW FEATURES: Shows 6 digits total in Litres (L) or KiloLitres (KL) up to 3 decimal place and rate in Litres per minute (L/M) or Litres per second (L/S) with 1 decimal place. (specify which at time of ordering) External re-calibrate via RFID and EWM software Wake-Reset function turns on the display before resetting the total. Default Display is LPM and total LITRES NEW OPTION:- 4 Digit Version with larger LCD display Reset Totaliser in Litres with optional dec.pl. Flowrate display version in LPM or LPS dec.pl.. Dual LCD Rate + Total Display Order Code Description Flowrange# LCD digital resetable (Litres, no decimal place, rate LPM 1dec.pl.) Litres/min MES20LCD6 20mm 6-digit LCD resettable total LITRES + rate LPM flowmeter, threaded ¾ BSP(m) ends MES25LCD6 25mm 6-digit LCD resettable total LITRES + rate LPM flowmeter, threaded 1 BSP(m) ends MES32LCD6 32mm 6-digit LCD resettable total LITRES + rate LPM flowmeter, threaded 1¼ BSP(m) ends MES40LCD6 40mm 6-digit LCD resettable total LITRES + rate LPM flowmeter, flanged 1½ BSP(f) ends NEW!!! MES20LCD6 LCD digital resetable (Litres, with 1 decimal place, rate LPM 1dec.pl) MES20LCD6DP1 20mm 6-digit LCD resettable total LITRES 1dec.pl + rate LPM flowmeter, threaded ¾ BSP(m) ends MES25LCD6DP1 25mm 6-digit LCD resettable total LITRES 1dec.pl + rate LPM flowmeter, threaded 1 BSP(m) ends Now with Hi-Impact industrial grade bronze display housing & lid (in lieu of polycarb.) Optionals:- -KL Total in KiloLitres -NRT No-reset of total NEW Bronze Housing -5F Flowrate only display version, 5 digit larger LCD, in LITRES/MIN. to 1 dec.place -5F -T Teflon-lined body. Add suffix to any 20mm MES-type flowmeter order code. -N 20mm NEW compact low profile body version (in lieu of current body) NFC.A Re-calibration software package install on Andriod or Laptop # The flowrange is for 1.5% accuracy. Can measure outside this flowrange, but at reduced accuracy. Flowrange is for water. For Admix flowrange, divide water flowrate by the Admix sg. (1) At ±5% accuracy, MES flowmeters can measure down to: 20mm: 0.5 Litres/min; 25mm: 1.0 L/m; 32mm: 1.5 L/m; 40mm: 2.8 L/m; -N body See for product data sheets. 14

18 1.4.4 MES20-S / -S-T with Ryton MTL chamber / Teflon coated body for Low.PH-chemicals and petroleum liquids. Widely used for Admixtures and aggressive chemicals, ideal for oil/petrol products. Ideal for Portable Batching applications. Ryton-MTL special Hi-chemical/petroleum-resistant measuring chamber, high chemical resistance ceramic-bar. magnet, black Nylon glass filled drive shaft and viton seals. Measures liquids to Specific Gravity 1.6 Nutating disc measuring principle. Small Impurities can pass through measuring chamber without jamming. Low hydraulic thrust minimises wear. Maximum working pressure: 1160 kpa. Teflon-lined version for corrosive liquids. Connection: threaded ¾ BSP (male) Digital pulse output version has exclusive 1 millilitre / 1 pulse output (for sg >= 1.1) requires +5 to 25 VDC supply supply current 5 to 25mA proportional to supply voltage. accuracy: ±1.5%, repeatability: ± 0.3% Pulse now with optional 1, 10, 100 or 1000 ppl. LCD resetable Total version closing the lid resets the display total. 4 or 5 digit LCD (without or with decimal place). internal Lithium battery powered (5-10 year battery life) accuracy: ±1.5%, repeatability: ± 0.3% Reed Switch pulse output version 61 pulses/litre (for sg >= 1.1) accuracy: ±1.5%, repeatability: ± 0.3% Mechanical display version Running (non-resetable) display. accuracy: ±1.5%, repeatability: ± 0.3% LCD6 rate + Total version 6-digit LCD shows Rate Litres/minute 1dp, Total Litres 1dp. accuracy: ± 2%, repeatability: ± 0.3% MES20-S (contains Hi-chemically resistant Ryton measuring chamber) Connection * Pulse Output for Flowrange# Order Code Size Bsp(m) Accuracy Specific Gravity >= 1.1 Display Display shows Resetable Temp Litres/min MES20-S 20 or 25 mm ± 1.5% 900 ppl Transistor No n/a 60 C 5-70 MES20R-S 20 or 25 mm ± 1.5% 54 ppl ReedSwitch No n/a 80 C 5-70 MES20-MR-S 20 or 25 mm ± 1.5% 54 ppl ReedSwitch Mechanical M 3 (down to 1 Litre) No 80 C 5-70 MES20LCD5DP-S 20 or 25 mm ± 1.5% n/a 5-digit LCD Litres, to 1 decimal place Yes 50 C 5-70 MES20LCD6DP-S 20 or 25 mm ± 1.5% n/a 6-digit LCD Litres 1 dec.pl +rate LPM Yes 50 C 5-70 MES20-S-T 20 or 25 mm ± 1.5 % 900 ppl Transistor No n/a 50 C 5-70 OPTIONAL TEFLON LINING All models with Standard Ceramic or Ceramic/Barium Magnet -T Teflon-lined body. Add suffix to flowmeter order code. * Note: pulse output rate is different for liquids with Specific Gravity < 1.1 e.g. for s.g = 1.0, pulse output rate is up to 10% less than that for s.g. 1.1 MES20-S (yellow body) (Transistor Pulse output, chemically resistant chamber) MES20-S-T (Black Body) (Teflon-coated pulse o/p, chemically resistant chamber) MES20LCD6 Flowrtate + Resetable LCD Total, -S Ryton MTL Chamber (Shown with viton or EDPM gaskets& Teflon spacer) # The flowrange is for 1.5% accuracy (±2% for Flowrate display). Can measure outside this flowrange, but at reduced accuracy. At ±5% accuracy, MES20-S flowmeters can measure down to 2 Litres/min. Flowrange is for water. For Admix flowrange, divide the water flowrate by the Admixture s Specific Gravity. PULSE RATE PER VOLUME VARIES SO METER MUST BE ONSITE CALIBRATION CHECKED ONCE. See for product data sheets. 15

19 1.4.5 SPARE PARTS for MES series flowmeters SPARE PARTS for MES20-S /-ST models only Product Code Description (for MES20-S /-ST Ryton-MTL chamber flowmeters) 20-5-S 20mm Ryton-MTL Chamber (chemical/petroleum resistant). Includes measuring chamber, viton base seal and Teflon spacer S Spacer -Teflon 20-DST Drive shaft - black Nylon glass filled. 20-CSM Ceramic Special Magnet special chemically resistant 20-5-S SPARE SEALS 20-6-S Chamber Gasket VITON (square) 20-6-S-EDPM Chamber Gasket EDPM (square) 20-7-S Base sealer gasket VITON (chemical/petroleum resistant) S-EDPM Base sealer gasket EDPM (chemicals special). * For the MES spares below, the Order Code format is size-code e.g is chamber for 20mm MES flowmeter Price SPARE PARTS for all MES models Code* Description 20mm 20mm ( N ) 25mm 32mm 40mm -1 Digital Smart Pulse Pulsehead (round) complete capsule -1R Reed Switch Pulsehead (square) complete capsule -1A LCD Rate/6digit reset total Litres display capsule Bronze Housing -1B LCD Rate/6digit reset Litres 1.dec.point display capsule Bronze Housing -1F LCD Flowrate (Lites/min, to 1 dec.pl.) display capsule Bronze Housing 1M Mechanical running (non-resettable) Total display capsule Poly. Housing -B Industrial Grade Hi-impact Bronze housing/lid (for upgrades of Poly) 2A Meter body (coupling-free, ¾ BSP male connection), without chamber 3 Strainer 5 Measuring chamber (complete with gasket) ceramic-barium magnet c/w plastic shroud 6 Chamber O ring 7 Base sealer gasket ring 8 Base plate Synthetic Polymer plastic 8P Base plate (PVC) for higher acidic liquids 8M Base plate (cast iron) } with Nylon inner cover plate (suits S and T) 9 Stainless 316 base screw 11 Nut/Tail/Gasket connection kit(pair)-for old body only (metric) 12 Connection washer (each) - for old body/gasket only 13 Oval flange kit (pair) BC SBU Chamber and New Body (parts 2A - 7, 8M and 9 above) Barrel Connection Unions Polyprop BSP(f) -comes as a pair NOTE : NEW N version compact low profile body and chamber for MES20 20mm sizes (top capsule is interchangeable) 2A. Meter Body 8. Base Plate 8M. Base Plate -1R 11. Nut/Tail/Gasket N SBU20 See for product data sheets. 16

20 * For spare MES capsule components, the Product Code format is size-code e.g. 25-g is a spare glass lens for a 25mm MES flowmeter Code* Description 71BLCD Reset capsule components a Housing Shroud (plastic) -B Housing Shroud (brass) and lid (brass) industrial grade bl Lid with magnet, for 20mm MES20LCD4 (4 digits, no dp) b Lid with magnet (for all other MES models) c hinge pin d locking plate e security pin f magnet g glass lens LCD Reset capsule components MES20-N parts New Brass Housing Note the position of the round magnet in the lids. Ceramic-Barium Magnet * For spare MES measuring chamber components, Product Code format is size-code e.g. 25-5C is a spare disc for a 25mm MES flowmeter Reseller Code* Description 20 mm 20mm (N) 25 mm 32 mm 40 mm Discount Measuring chamber internal components New Chamber 5AAA Control block assembly with fixed Chamber top 5AA Control block assembly 5A Chamber top only 5B Shutter plate 5C Wobble disc 5D Roller guide pin 5E Chamber bottom only 20-M Magnet 20-CB Magnet ceramic/barium chemical resistance c/w shroud 20-CSM Magnet - ceramic high chemical resistance * 20-DST Drive shaft, black Nylon glass filled (for 20mm flowmeter only) * * If converting standard MES20 to use the 20-CSM high chemical resistance magnet, then the 20-DST black drive shaft must also be used. Polyprop barrel union connectors See page M 20-DS Measuring chamber internal components See for product data sheets. 17

21 1.5 PSM domestic water flowmeter Compliance with NMI R49-1 Australian Standards AS Pattern Approved Designed for the measurement of cold potable water. Accurate; long maintenance-free life; highly resistant to tampering. For pipe diameters from 15 to 40 mm. Optional pulse output (via T-probe). Cannot be disassembled whilst in service and the mechanically driven counter cannot be interfered with magnetically. A lead seal will reveal any attempt to dismantle the meter. Positive displacement volumetric rotary piston principle of measurement ensures registration even at the very lowest rates of flow with accuracy maintained over the flow range. No calibration required throughout its lifespan. A large surface area fine filter fitted on the measuring chamber inlet prevents damage by gathering solid particles. A partially obstructed filter will not affect the meter s accurate registration. Shows total in KiloLitres and Litres. Mechanically driven number counter. Maximum registration kl (for 5x3 number wheel counter models). ± 2% accuracy. ± 0.15% repeatability. (Start 5%) Advanced engineering plastics measuring chamber. Pulse output option (can be retro-fitted). Max. Operating Temp: 50 ºC. Max. Operating Pressure: 1400 kpa mm models supplied with Gasket Seat couplings mm models supplied with flange kits. Gunmetal Body Construction. Supplied with Flanged. Gasket Seat couplings. Flowrange (Litres/min) * Order Code Description Connection Start Min. Max. Max. PSM15 15mm flowmeter, with running (non-resetable) mechanical totaliser BSP (male) nut & tail PSM20 20mm flowmeter, with running (non-resetable) mechanical totaliser, (5 x 3 dial) Gasket Seat couplings PSM20A 20mm flowmeter, with running (non-resetable) mechanical totaliser, (4 x 4 dial) Gasket Seat couplings PSM25 25mm flowmeter, with running (non-resetable) mechanical totaliser Gasket Seat couplings PSM32 32mm Oval Flanged, 2 bolt BSP(f) PSM40 40mm Oval Flanged, 2 bolt BSP(f) PSM20-TP 20mm flowmeter, with running mechanical totaliser, and pulse o/p (1 pulse/ 5 Litres) Gasket Seat couplings PSM20A-TP 20mm (1 pulse/ 0.5 Litres) Gasket Seat couplings Optional -TP T-probe Reed Switch pulse output (as option, as spare, or can be retro-fitted to PSM flowmeter). For PSM20A: provides 1 pulse/ 0.5 Litres. For all other PSM flowmeters : provides 1 pulse/ 5 Litres. -BSC Ball Seat connection and couplings (for NSW) instead of Gasket Seat couplings (for 20 or 25mm models) PSM20-TP * The stated flowrange is for 2% accuracy. Can measure outside this flowrange, but at reduced accuracy. optional T-probe pulse output See for product data sheets. 18

22 72B 1.6 CT5 domestic water approved flowmeters high pulse rate for precision data logging for water studies Order Code Conventional Type Models:- Flowrange* Litres/min CT5-S20 CT5-S20 CT5-S25 20mm mechanical totaliser / Contact closure switched pulse output (nominal 72 ppl) to 30 C (to 50 C for < 2 hours). Accuracy: ± 2%. To 1500 kpa. With single check valve. Couplings included - Gasket Seat (i.e. for VIC, QLD etc) ¾ BSP(m) 25mm mechanical totaliser / contact closure switched pulse output (nominal 36ppl).1500kPa. to 30 C (to 50 C for < 2 hours). Accuracy: ± 2%, Repeatability of rate ± 0.1%. With single check valve. Couplings included - Gasket Seat 1 BSP(m) CT5-S25 Manifold Type Models:- CT5-S20-M-15 Manifold flowmeter 121ppl. SCV e.g. for NZ-Water etc (with 15mm flow range). G 1½ thread CT5-S20-M-20 Manifold flowmeter 72ppl. DCV e.g. for QLD-Water & others (20mm flow range) G 1½ thread MCT20-NZ Manifold coupling cast. G 1 ½ -BSP-F with 20mm ¾ BSP (male) ends (by Accuflo) MCT20 Manifold coupling cast. G 1 ½ -BSP-F with 20mm ¾ BSP (male) ends (by StrongCast) CT5-S -BS20/25 Client supplies the standard mechanical totaliser flowmeter to ManuFlo, ManuFlo converts flowmeters with high pulserate technology option Optionals:- 20/25mm BSP female Ball Seat connection for NSW (in lieu of Gasket Seat connections) CT5-S20-M-20 CT5-S20-M-15 -DCV Dual Check valve MCT20 MCT20-NZ Used in Water Studies in Australia, Germany, Iran, NZ, UAE and other locations inconjunction with a Datalogger capable of 100Hz+ input count range. 1.7 Data Loggers ME-USB-5+ DataCell-D & RTX option Counter, Event and State USB Data Logger. 1 event count input (not scaleable). Volt-free normally open contacts, or input voltages up to 24 VDC. Stores up to 1,000,000 timed events/intervals in counter mode (100Hz input). With internal 1yr Lithium.bat. 3.6v 1/2AA, Windows control software and measurement leads. Suitable for low pulse resolution flowmeters e.g. 1 pulse per 1 Litre, (or e.g. 5, 10,100,1000 ltrs). Compact Aegis data logger, for industrial and commercial logging applications. IP67 enclosure. Waterproof to 1 meter. Powered by long-life Lithium battery pack Stores 2 million records. (100Hz input speed). 4 programmable inputs. Delivers information locally and via GSM and GPRS. SMS and data collection WASP2-3G-1L Wireless Outpost logger 1 input with GSM coverage, upto 10yr bat. IP68. Web portal. Aegis OutPost TWIZ -CW TraceWizard Software: analyses data logs to find out where and how water is used. ManuFlo mounts/connects & wires and tests chosen logger to flowmeter of choice See for product data sheets. 19

23 1.8 S C HOT WATER flowmeters, with optional pulse output Order Code Description (Accuracy ±2%, to 90 C) Single-jet turbine water flowmeter; to 16 bar Flowrange* (L/min) S mm flowmeter, running totaliser (or GSD5-15 offered) S R10 15mm flowmeter, running totaliser, Reed switch pulse output (1 pulse/ 10 Litres) S P 15mm flowmeter, volt-free contact switch pulse output (30 pulses/litre) *(ideal for flowrate apps.) S mm flowmeter, running totaliser ( or GSD5-20 offered) S R10 20mm flowmeter, running totaliser, Reed switch pulse output (1 pulse/litre) GSD-B mm flowmeter, running totaliser, Reed switch pulse output (1 pulse/ 1 Litre)(or ME4-15-R1) GSD-B mm flowmeter, running totaliser, Reed switch pulse output (1 pulse/ 1 Litre) For Larger Sizes 20,25,32,40 and 50mm ask for MBH model flowmeter range (with optional pulse output). POA *starts from lower rates at reduced accuracy. 1.9 WP-D Turbine water flowmeters, mechanical total, optional pulse output ideal for measurement of high relatively constant flow rates e.g. behind pumps hermetically sealed register (IP68) can be rotated through 360 Range exceeds of the Australian Standard AS Measurement Class 2 requirements. Usually ex-stock items. AUSTRALIAN PATTERN APPROVED FLOWMETERS FROM GERMANY accuracy: ±2% To 1600 kpa. To 50 C. Table D flanged. ME5-T-B Remote IP65 LCD bat.pwr reset counter with Scalable input Flowrange (L/min) Order Code Description min ±5% min ±2% max ±2% WP-D40 40 mm running mechanical Totaliser WP-D50 50 mm WP-D65 65 mm WP-D80 80 mm WP-D mm WP-D mm RD-10 Options Reed Switch pulse output. 1 pulse/10 Litres. For connection to battery powered devices. ME5-T-B # LCD 5-digit resetable Totaliser (large display, K-factor) indicator, with pulse output option. IP65 wall mount enclosure. Internal 10yr Lithium battery powered PWMR Paddlewheel Mechanical Water Meters with Pulse Output Used for dirty water in irrigation/agriculture. Can pass some solids. Solid and robust design. Measures liquid to to 50 C kpa (PN16). 360 rotating fully encapsulated counter. Scratch resistant glass on register. Reed Switch pulse output, switching up to 6vac/DC, 0.10 Amps Flowrange (Litres/min) Order Code Size Pulse Output Connection Min. (±5%) Min. (±2%) Max. (±2%) PWM050R 50 mm 1 pulse/ 10 Litres BSP (male) PWM080R 80 mm 1 pulse/ 100 Litres Table E PWM100R 100 mm 1 pulse/ 100 Litres Table E PWM150R 150 mm 1 pulse/ 1000 Litres Table E PWM200R 200 mm 1 pulse/ 1000 Litres Table E ,333 See for product data sheets. 20

24 1.11 MEHR Multi-jet and Turbine cold water mechanical totaliser flowmeter (optionally also with pulse output) Ideal for irrigation and process applications. Ideal for gravitational low flows, cooling towers etc. Small impurities are able to be passed without blockage. Running (non-resetable) mechanical total. Contact Switch pulse output versions available. Can connect pulse output models to ManuFlo Indicators to provide resetable total display. ± 2% accuracy (Qtransitional - Qmax) To 50 ºC. To 1000 kpa (PN10). Available in sizes of 15 to 300mm. Sizes 15 to 50mm with 1 pulse/litre output. Order Code Description Flowrange (L/min) min ±5% min ±2% max ±2% MEH15R1 15 mm Totaliser with reed pulse o/p (1 pulse/ 1 Litre ) with BSP (male) couplings. Multi-jet MEH20R1 20 mm MEH25R1 25 mm MEH32R1 32 mm MEH40R1 40 mm (1 pulse/ 1 Litre ) with BSP (male) couplings. Multi-jet MEH50R1 50 mm R10 Options for all above sizes (1 pulse/10 litres) MEH50FR10 50 mm Totaliser with reed pulse o/p (1 pulse/ 10 Litres) Table D flanged. Turbine type MEH80R mm Totaliser with reed pulse o/p (1 pulse/ 100 Litres) Table E flanged. Turbine type MEH100R mm (1 pulse/ 100 Litres) MEH150R mm (1 pulse/ KL Litre ) MEH200R mm (1 pulse/ KL Litre ) Ideal with MEH250R mm (1 pulse/ KL Litre ) MEH300R mm (1 pulse/ KL Litre ) MEH15 15 mm multi-jet flowmeter, running mechanical Totaliser, BSP (male) couplings MEH20 20 mm MEH25 25 mm MEH32 32 mm MEH40 40 mm MEH50 50 mm MEH20 MEH50-F 50 mm turbine flowmeter, running mechanical Totaliser, Table D flanged MEH80 80 mm turbine flowmeter, running mechanical Totaliser, Table E flanged MEH mm MEH mm MEH mm MEH mm MEH mm MEH80 -RS Reed Switch pulse module, for MEH sizes 15 to 50mm (can be retrofit to flowmeters) Flowmeters with Pulse o/p are suitable for use with ManuFlo Wall mount IP65 Resetable LCD (pulse input scalable) counter indicators bat.pwr e.g., ME5-T-B or ME6 NOTE: NOT SUITABLE FOR FLOWRATE INDICATORS DUE TO LOW RESOLUTION PULSE RATES ME5-T-B Reset counters See for product data sheets. 21

25 81B 1.12 TMW25 Turbine LCD resettable plastic flowmeters (for water/urea only) Order Code Description Flowrange* Litres/min TMW25 25mm (1 bsp-f) inline plastic LCD integral resettable total + grand totaliser, acc.+/-5% TMW25FT As above but includes additional flowrate display, litres /min flowrange Ideal for hoseguns, AAA battery powered (not approved for drinking water apps.) Compact and Lightweight Design for general purpose use TMW A FM25 Mechanical Resettable Fuel Meters (for Diesel, Kerosene, Petrol, Oils) Order Code Description Litres/min FM25 25mm (1 ) fuel meter. Large digits. Ideal for Petroleum, Oils, Hyrocarbons With Large display mechanical resettable total and running Total. 1 BSP (female) connection. Suitable for gravity installations. Accuracy: +/- 1%. Nutating disc or oval rotor measurement principle. to 344 kpa (50 psi); weight: 2kg. Aluminium body FM B CR25 Oval Rotor positive displacement flowmeter (for corrosive chemicals ) ideal for non-conductive fluids Order Code CR25 CR09 (MX) Description 25mm (1 )Bsp-f Oval Gear all Ryton (PPS) pulse flowmeter to 80 C ( 52 ppl). Contact closure pulse (Pressure to 1000kPa) Accuracy ± 1.5%. 8mm (1/4 )BSP-f Oval Gear Ryton Rotors, S/S316 Body pulse flowmeter to 80 C ( 400 ppl). Contact closure pulse, Accuracy ± 1.5%. Other sizes and material specification Flowmeters to suit most liquids on request. e.g. Aluminium, Stainless-Steel, PPS Flowrange* Litres/min C ME7 LCD Totaliser Description LCD 7-digit reset Totaliser counter. Panel mount. 1 input pulse = 1 count on display. Internal battery powered, 8-10 year battery life. (Can connect up to 30 metres away). See for product data sheets. 22

26 1.13 AMM Admixture Mini Mag. Compact Admixture Flowmeters (sizes mm) Very compact and light weight design electromagnetic flowmeter. 15 and 20mm models are directly interchangeable with MES20 20mm flowmeters. Measurement range: 0.2 to 10 ±2% accuracy. To 1000 kpa (10 bar). BSP(male) threaded end connections. Supplied with BSP (female) couplings. PVDF lined sensor, Stainless Steel 316 electrodes with integrated grounding rings. Virtually maintenance free, with no moving parts. Measures liquids with conductivity > 20 S/cm, to 40 C. Accuracy is unaffected by varying viscosity or specific gravity of liquids. 12 VDC powered (can be directly powered from ManuFlo devices (optional 24 VDC for use directly with 24V PLCs). Easy plug-in wiring connections via DIN43650-A plug set to IP65 rating. Forward direction pulse, NO empty pipe detection Order Note: Pipeline at Sensor must be full at all times. Pulses / Flowrange Code Description Litre (Litres/min) AMM15 ½ MiniMag (15mm connection, 8mm bore). With pulse output AMM20 ¾ MiniMag (20mm connection, 12mm bore). With pulse output AMM25 1 MiniMag (25mm connection, 20mm bore). With pulse output OPTIONS VDC powered (instead of 12 VDC powered) 1.14 MM MiniMag compact Electromagnetic Flowmeters with Display (sizes mm) Low-cost, very compact and light-weight design. No moving parts. Virtually maintenance free. Pre-programmed for your application. 4-digit on-board LED display shows non-resetable Total (Litres) or Flowrate (Litres/min). Measured liquid must have conductivity of at least 20 µs/cm. NPN Open Collector pulse output. 4-20mA output. With M12 connection and 5-metre cable lead. Accuracy: ±2%; Repeatability: ±0.2%. To 16 bar; to 70 ºC; weight: 0.5 kg; VDC powered. Stainless Steel body, PEEK liner, SS316 electrodes. IP67. Empty pipe Pulses / Flowrange Order Code Description Detection Litre (Litres/min) MM10 ¼ MiniMag (15mm connection, 4mm bore) electromagnetic flowmeter. yes MM15-P ½ MiniMag (15mm connection, 8mm bore) electromagnetic flowmeter. (until soldout) no MM15 ½ MiniMag (15mm connection, 8mm bore) electromagnetic flowmeter. no MM20 ¾ MiniMag (20mm connection, 12mm bore). no MM25 1 MiniMag (25mm connection, 15mm bore). no OPTIONS CV12 12 VDC input to 24 VDC output power step-up converter external module. 2 Amp. [ AA-0264 ] See for product data sheets. 23

27 1.15 SMP Budget Battery-powered Electromagnetic Flowmeters Flowrange (Litres/min) Order Weight Minimum Max Code Description (kg) ±5% ±3% ±1% SMP025 25mm battery powered electromagnetic flowmeter. Has empty pipe detection integral display, with Flowrate (Ltr./sec.) & non-resetable 8-digit Total (m 3 to 1 dec.pl). powered by 2x C-size Lithium batteries (typical replaceable life: 2-4 years). Coupling Connection Kit with straight NPT (female) threaded ends. Glass-filled polypropylene body. 316 Stainless Steel electrodes. From 50m/s conduct. IP66. To 1030 kpa. To 54 ºC. Accuracy: ± 1% (from % of reading). SMP050 50mm battery powered electromagnetic flowmeter. With coupling kit SMP080 80mm battery powered electromagnetic flowmeter. With coupling kit LITH Optional replacement Lithium batteries, 2x C size (typical replaceable life: 2-4 years) 1.16 MFS MagMaster Electromagnetic Flowmeter with display and outputs * SPARE PARTS & REPAIR SERVICE * Transmitter/display IP65 units All transmitters are vac powered. All display and output parameters custom programmed; re-programmable via serial com port using Windows HyperTerminal. Minor Repairs where possible charged at $140/hr. Note: Minimum charge policy Re-programming service available SPARES 313-TR1 313-LCD MFS-WAND -TRB HBM2500 SERVICE-MAG Transmitter/display in enclosure complete, vac powered (reconditioned units) LCD dot matrix back-lit display module Spare magnetic swipe wand, on Stainless Steel cable Totaliser Reset Button IP65 hinged outer waterproof ABS protective enclosure for display, with clear lid. Total Recondition/Test/repair/calibrate Magmaster Transmitter-Display & Sensor NOTE: Various new old stock & preloved models occasionally available sizes mm. POA. NOTE: Ongoing Service/Repair/Calibration/Programming support. See for product data sheets. 24

28 1.17 RMS Rosemount High Pressure Process Electromagnetic (GROUT) Flowmeters (FM - Hazardous Approval) Measures: Liquid Grout, Slurries, Oxides, Silica, Chemicals & Recycled waters. Robust alloy housed integral mounted electronics 8732E-AX with toughened glass face. With LCD Display Module (-M4) shows dual line flowrate & acumulative or resettable totaliser. Repositionable in 90 degree angle steps to suit install. (Programmable to desired engineering units). All units pre-programmed to desired settings, prewired and flow tested, ready for install. WAFER (8711) HIGH PRESSURE SENSOR FOR GROUT to 5100kPa. or FLANGED ANSI-150 (8705) sensor with Tefzel or Teflon liner, Stainless Steel 316 or Hastelloy-C electrodes (With Empty Pipe detection). Process liquid requires a conductivity of at least 5 microsiemens/cm. Measures velocity range m/s. Accuracy ±0.5% of rate (0.9 to 10 m/s). Liquid temperature: Integral: -20 to 70 ºC, Remote: -20 to 149 ºC for Tefzel liner. Pressure: mm wafer sizes to 740 psi (5100 kpa) #8711 HIGH PRESSURE, 4-8mm wafer & mm flanged sizes #8705 to 290 psi (2000 kpa). Pulse and 4-20mA outputs. Power supply standard vac, or optional VDC. Fully programmable to user specification via HART protocol or -M4 local display. Approved for Class III Hazardous Applications (NEMA 4x). (Upto 80% solids) Coils set on 30Hz for Grout/oxides/slurries RMS 8732 transmitter with 8711 wafer sensor flowmeter RMS wafer sensor flowmeter with M4 LCD display, with earthed PVC flange connection kit RMS 8712DR remote display/transmitter & 8705 flanged sensor Flowrange (Litres/min) Order Code Description min (±10%) min (±5%) min (±0.5%) max (±0.5%) RMS004 -M4 4 mm Wafer sensor (8711), S/S316 or Hast-C electrodes, Tefzel or Teflon liner, vac. with backlit LCD display: dual line flowrate & acumulative or resettable totaliser RMS008-M4 8 mm RMS015-M4 15 mm RMS025-M4 25 mm RMS040-M4 40 mm RMS050-M4 50 mm RMS080-M4 80 mm RMS100-M4 100 mm RMS150-M4 150 mm OPTIONS to order, add as suffix to the RMS flowmeter product code -DC DC powered transmitter VDC (or VDC). -TRB External Totaliser Reset Button for manual batching (with AX-model) -F 15-50mm: ANSI-150 flanged Sensor (8705) -R Remote mounted Display-Transmitter from Sensor via 2mtr signal cable (longer on request) Ideal for high temperature applications to 177 ºC (Teflon liner), 149 ºC (Tefzel liner). Process Temp: mm sizes to 135 ºC, 4-8mm sizes to 90 ºC. -IS Intrinsically safe S/S rated gland entries. (remove -M4) Blind pulse and 4-20mA only no LCD display module fitted (Subtract $450.00) 8732E-M4 (Display) 8711 (Sensor) TRB (Total Reset) See for product data sheets. 25

29 1.18 KMS Series. K-MAG Electromagnetic Flowmeters KMS703 Electromagnetic Internal Battery Powered Flanged Flowmeters with S70 display with pulse outputs For waste water, bore water, irrigation and liquids on application. Internal battery powered - ideal for remote locations, or where a external power supply is not available. Rugged construction with no moving parts ensures long, maintenance-free flowmeter life. Flowrate and Bi-directional Totaliser electronic display housed industrial grade rugged enclosure. Display can be either integral, or remote via pre-wired cable to required length. Pulse output -for connection to external reset counter or PLC. 50Hz max., 50% nominal duty cycle. Internal Version x 4 internal D-batteries. Typically 3 to 5 year battery life. Site-replaceable batteries. Remote Version internal or remote battery pack. IP68 Potting pack for remote sensor included. 10 metre cable. Earthing via internal 316 s/s electrodes Measured liquid must have conductivity >50μS/cm Accuracy: ±0.3% + 1 mm/s Temperature range: 0 to 50 C; Pressure: to 1600 kpa (Flanged CL16). Rectangular bore sensor for flow profiling means zero pipe runs before or after the meter. K-MAGS Fully custom programmed engineering units at time of order INTEGRAL VERSION Rectangular Bore Sensor (0 straight pipe lengths needed) Flowrange (Litres/min) Order Code Description min (±5%) min (±2%) max (±0.5%) KMS F 25mm, Table-D flanged, Rilsen liner, SST 316L Measuring & Grounding Electrodes KMS F 40mm KMS F 50mm AS4087 flanged, Rilsen liner, SST 316L Measuring & Grounding Electrodes KMS F 80mm KMS F 100mm KMS F 150mm REMOTE VERSION Rectangular Bore Sensor (0 straight pipe lengths needed) Reseller Order Code Description min (±5%) min (±2%) max (±0.5%) KMS F-R 25mm, Table-D flanged, Rilsen liner, SST 316L Measuring & Grounding Electrodes KMS F-R 40mm KMS F-R 50mm AS4087 flanged, Rilsen liner, SST 316L Measuring & Grounding Electrodes KMS F-R 80mm KMS F-R 100mm KMS F-R 150mm Options for KMS703 KBMBAT Replacement Batteries ( Dual 3.6v lithium D cell batteries) price for dual pack -RP 3-metres cable connection for pulse output to remote resettable display via MIL-spec plug e.g. wire to ME5-T-B or Datalogger ME5-T-B External reset Totaliser, Lithium battery operated. -20M 20 metre cable (instead of 10 metres) between sensor and display, for remote version. NOTE: Larger Sizes Available See for product data sheets. 26

30 KMS501W Electromagnetic Wafer Flowmeters with S50 display & outputs (ideal for Tradewaste and Bore Water) For waste water, bore water and irrigation (upto 10% solids). K-MAGS Fully wired and custom programmed, ready to use. PFA (Teflon) liner, Hastelloy C electrodes, Wafer connection Virtually maintenance free. No moving parts. Self verifying. Accuracy: ±0.5% of MV +1 mm/s vac or vdc powered Totaliser up to 8 digits. With Flowrate display. Optionally fitted with Sydney Water Tradewaste MIL-Spec sampler & 4-20mA output plugs, and for other water authority requirements. Integral display or remote via 2-metres cable to flowsensor. Durable cast alloy display enclosure. Grounding earth ring supplied. Programmable via 4 tactile buttons or via magnetic wand or via HART to PC. IP68 flow sensor (remote version when potted). Process temperature: -25 to 120 ºC. Measured liquid must have conductivity of at least 5 µs/cm (20 µs/cm for water) (add -R code) Flowrange (Litres/min) Order Code Description with Integral Display with Remote Display min. (±3%) min (±0.5%) max (±0.5%) KMS W 15 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac KMS W 25 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac KMS W 40 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac KMS W 50 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac KMS W 80 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac KMS W 100 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac KMS W 150 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac OSC-I On-site calibration check (Sydney greater metropolitan area), Initial: as required by Sydney Water after flowmeter installation and then at least yearly. Thereafter: OPTIONS to order, add as suffix to the KMS flowmeter product code -R Remote wired display/transmitter with 2m cable -TW -DC Fitted with Sydney Water Tradewaste sampler plugs (other authorities on request) VDC powered. -XC Extra cable (where n in Product Code = extra cable length in metres) -TW-R Remote MIL.spec Sampler/mA outputs plug pack, wall mountable -TW-R SPARES & ACCESSORIES TWSPS Trade Waste Sampler Pulse Splitter. SJP Sensor Junction Potted for IP68 applications where sensor is located in pit # The flowrange is for the stated accuracy. Flowmeter can measure below this flowrange, but at reduced accuracy. - PVC/GAL flanged Connection Kits available See for product data sheets. 27

31 KMS502F Electromagnetic Flanged Flowmeters with S50 display & outputs (ideal for Tradewaste and Bore Water) For waste water, bore water, irrigation (upto 10% solids). K-MAGS Fully wired and custom programmed. Hard Rubber liner, Hastelloy C electrodes Australian Flanges Virtually maintenance free. No moving parts. Self verifying. Accuracy: ±0.5% vac or vdc powered Totaliser up to 10 digits. With Flowrate display. Optionally fitted with Sydney Water Tradewaste MIL-Spec sampler & 4-20mA output plugs, and for other water authority requirements. Integral display or Remote, via 2-metres cable to flowsensor. Durable cast alloy display box. Grounding earth ring supplied. Programmable via 4 tactile buttons or via magnetic wand or HART to PC. IP68 flow sensor (remote version when potted). Process temperature: -5 to 80 ºC. (hard rubber) Measured liquid must have conductivity of at least 5 µs/cm (20 µs/cm for water) (add -R to code) Flowrange (Litres/min) Order Code Description with Integral Display with Remote Display Reseller Discount min (±1%) min (±0.5%) max (±0.5%) KMS F 25 mm AS2129 (Table E) flanged, Hard Rubber liner, Hastelloy C electrodes vac KMS F 40 mm AS2129 (Table E) flanged, Hard Rubber liner, Hastelloy C electrodes vac KMS F 50 mm AS4087 Class 16 flanged, Hard Rubber liner, Hastelloy C electrodes vac KMS F 80 mm KMS F 100 mm KMS F 150 mm KMS F 200 mm OSC-I On-site calibration check (Sydney greater metropolitan area), Initial: as required by Sydney Water after flowmeter installation and then at least yearly. Thereafter: OPTIONS to order, add as suffix to the KMS flowmeter product code -R Remote wired display/transmitter with 2m cable -TW -DC -XCn -TW-R TWSPS SJP Fitted with Sydney Water Tradewaste sampler plugs (for other authorities on request) VDC powered Extra cable (where n in Product Code = extra cable length in metres) Remote MIL.spec Sampler/mA outputs plug pack, wall mountable SPARES & ACCESSORIES Trade Waste Sampler Pulse Splitter. Sensor Junction Potted for IP68 applications where sensor is located in pit **Larger flow sensor sizes available on request** - PVC/GAL flanged Connection Kits available -TW-R See for product data sheets. 28

32 KMS506-S Electromagnetic Flowmeters for Hygeinic Use with S50 or S100 Display & Outputs. Applications include: Exact blending, dosing and batching, Beverages including soft drinks, beer, wine and fruits juices, Milk and other dairy products K-MAGS Fully wired and custom programmed, ready to use. PFA (Teflon) liner, Hastelloy C electrodes, Sanitary connections are Tri-clamp Virtually maintenance free. No moving parts., Self verifying. Accuracy: ±0.5% of MV + 1mm vac or vdc powered, Durable cast alloy display enclosure. Totaliser up to 10 digits. With Flowrate display. Pulse & ma outputs. Integral display or remote via 2-metres cable to flowsensor. Programmable via 4 tactile buttons or via magnetic wand or via HART to PC. IP68 flow sensor (remote version when potted). Process temperature: -40 to 120 ºC (integral display) -40 to 140 C (remote display). Measured liquid must have conductivity of at least 5 µs/cm (20 µs/cm for water) Suitable for CIP cleaning including acids and caustic solutions Ideal for Food & Beverage & Pharmaceutical Applications Order Code Description with S50 Integral Display Add -R code for S50 with Remote Display Reseller Discount Flowrange# min. (±3%) (Litres)min (±0.5%) max (±0.5%) KMS506-S-015 ½ Tr-clamp connection, PFA liner, Hastelloy-C electrodes vac KMS506-S Tr-clamp connection, PFA liner, Hastelloy-C electrodes vac KMS506-S-040 1½ Tr-clamp connection, PFA liner, Hastelloy-C electrodes vac KMS506-S Tr-clamp connection, PFA liner, Hastelloy-C electrodes vac KMS506-S Tr-clamp connection, PFA liner, Hastelloy-C electrodes vac KMS506-S Tr-clamp connection, PFA liner, Hastelloy-C electrodes vac OPTIONS to order, add as suffix to the KMS flowmeter product code S100 Display Version -R Remote wired display/transmitter with 2m cable -JBSS -XC -DC -SJP Sensor Junction Box in 316 SST instead of standard aluminium (only remote version) Extra cable (where n in Product Code = extra cable length in metres) VDC powered. Sensor Junction Potted for IP68 applications where sensor is pressure cleaned Optional Higher Specification Display Version S100:- KMS106-S With S100 Higher Specification Display to +/- 0.3% Accuracy (Integral version mount 0 or 45 ) -R With S100 Higher Specification Display to +/- 0.3% Accuracy (Remote version inc. 2m cable) -S100 -S100 -S100R -DC S100 Display with VDC powered Integral 45 Integral 0 Remote -TRB External Totaliser Reset Button for manual batching (only available with S100 Display) -xxx Insert the pipe size diameter e.g is 50mm size sensor # The flowrange is for the stated accuracy. Flowmeter can measure below this flowrange, but at reduced accuracy. See for product data sheets. 29

33 KMS101W Electromagnetic Wafer Flowmeters with S100 display & outputs (ideal as resettable/batching meter) For ADMIXTURE Batching, Shotcrete, Mild-Recycled Water & Selected Chemical Applications (upto 20% solids) K-MAGS Fully wired and custom programmed to requirement. Polypropylene liner, Hastelloy C electrodes, ANSI 150 lb Flanges Virtually maintenance free. No moving parts. Self verifying. Accuracy: ±0.3% +1 mm/s vac or vdc powered Totaliser up to 8 digits. With Flowrate display. Totaliser resettable via optional pushbutton. Display can be Remote (2-metres cable to flowsensor) or Integral (45 or 0 mounted) Empty pipe detection. Durable cast alloy display enclosure. Grounding earth ring supplied. Programmable via 4 push buttons or via HART to PC. IP68 remote flow sensor (when potted). Process temperature: -25 to 120 ºC. Measured liquid must have conductivity of at least 5 µs/cm (20 µs/cm for water) (add -R code) Flowrange (Litres/min) Order Code Description with Integral Display with Remote Display min. (±3%) min (±0.5%) max (±0.5%) KMS W 15 mm Wafer connection, PFA SS reinforced liner, Hast-C electrodes vac KMS W 25 mm Wafer connection, PFA SS reinforced liner, Hastelloy C electrodes vac KMS W 40 mm Wafer connection, PFA SS reinforced liner, Hastelloy C electrodes vac KMS W 50 mm Wafer connection, PFA SS reinforced liner, Hastelloy C electrodes vac KMS W 80 mm Wafer connection, PFA SS reinforced liner, Hastelloy C electrodes vac KMS W 100 mm Wafer connection, PFA SS reinforced liner, Hastelloy C electrodes vac KMS W 150 mm Wafer connection, PFA SS reinforced liner, Hastelloy C electrodes vac OPTIONS to order, add as suffix to the KMS flowmeter product code -R Remote wired display/transmitter with 2m cable -TRB -DC -XC Totaliser Reset Button VDC powered. Extra cable (where n in Product Code = extra cable length in metres) **Larger flow sensor sizes available on request** # The flowrange is for the stated accuracy. Flowmeter can measure below this flowrange, but at reduced accuracy. - PVC/GAL flanged Connection Kits available See for product data sheets. 30

34 KMS102/4F Electromagnetic Flanged Flowmeters with S100 display and outputs (ideal as resettable/batching meter) For ADMIXTURE Batching, Shotcrete, Mild-Recycled Water & Selected Chemical Applications (upto 20% solids) K-MAGS Fully wired and custom programmed to requirement. Polypropylene liner, Hastelloy C electrodes, ANSI 150 lb Flanges Virtually maintenance free. No moving parts. Self verifying. Accuracy: ±0.3% +1 mm/s vac or vdc powered Totaliser up to 8 digits. With Flowrate display. Totaliser resettable via optional pushbutton. Display Remote (all sizes, 2-metres cable to flowsensor) or Integral (45 or 0 mounted) Empty pipe detection. Durable cast alloy display enclosure. Grounding earth ring supplied. Programmable via 4 push buttons or via HART to PC. IP68 remote flow sensor (when potted). Process temperature: -25 to 120 ºC. Measured liquid must have conductivity of at least 5 µs/cm (20 µs/cm for water) (add -R to code) Flowrange (Litres/min)# Order with with min min max Code Description Integral Display Remote Display (±3%) (±0.3%) (±0.3%) KMS104P-006F 6 mm ANSI 150 LB flanged, PTFE liner, Hastelloy C electrodes vac KMS104P-010F 10 mm ANSI 150 LB flanged, PTFE liner, Hastelloy C electrodes vac KMS104P-015F 15 mm ANSI 150 LB flanged, PTFE liner, Hastelloy C electrodes vac KMS102P-025F 25 mm ANSI 150 LB flanged, Polypropylene liner, Hast-C electrodes vac KMS102P-040F 40 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS102P-050F 50 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS102P-080F 80 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS102P-100F 100 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS102P-150F 150 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac OPTIONS to order, add as suffix to the KMS100 flowmeter product code -R Remote wired display/transmitter with 2m cable -TRB -DC -XCn Totaliser Reset Button VDC Powered Extra cable (in excess of standard 2 metres), where n in Product Code =extra cable length in metres) **Larger flow sensor sizes available on request** # The flowrange is for the stated accuracy. Flowmeter can measure below this flowrange, but at reduced accuracy. See for product data sheets. 31

35 KMS302F Electromagnetic Flanged Flowmeters with S300 display and outputs (for grout, oxides and slurries) For grout, oxides, silicafume, recycle-water & selected slurry applications (upto 50% solids). Polypropylene liner, Hastelloy C electrodes, ANSI 150 lb Flanges K-MAGS Fully wired and custom programmed. Flow sensor sizes 25 to 150mm Flanged connection suites ANSI 150lb flanges Self verifying. Accuracy: ±0.3% vac or vdc powered Totaliser up to 10 digits. With Flowrate display. Integral display or Remote via 2-metres cable to flowsensor. Durable cast alloy display box (integral) or plastic (remote). Pulse and 4-20mA outputs. HART protocol. Programmable via reflective buttons or via HART to PC Built in flow profiler for higher accuracy Self verifying Accuracy: ±0.3% IP68 remote flow sensor (when potted). Empty pipe detection. Pressure rating to 1600 kpa: Process temperature: -25 ºC to 120 ºC Measured liquid must have conductivity of at least 1 µs/cm (20 µs/cm for water) vac powered. Optional vdc. IDEAL FOR GROUT MEASUREMENT (add -R to code) Flowrange (Litres/min)# with min min max Order Code Description Integral Display Remote Display (±1%) (±0.3%) (±0.3%) KMS302P-025F 25 mm ANSI 150 LB flanged, Polypropylene liner, Hast-C electrodes vac KMS302P-040F 40 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS302P-050F 50 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS302P-080F 80 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS302P-100F 100 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac KMS302P-150F 150 mm ANSI 150 LB flanged, Polypropylene liner, Hastelloy C electrodes vac OPTIONS to order, add as suffix to the KMS flowmeter product code -R Remote wired display/transmitter with 2m cable -TRB -DC -VR -XCn Totaliser Reset Button VDC powered Virtual Reference grounding option for IFC300 (instead of grounding rings on corrosive media) Extra cable (in excess of the standard 2 metres), where n in Product Code = extra cable length in metres) PVC/GAL flanged Connection Kits available # The flowrange is for the stated accuracy. Flowmeter can measure below this flowrange, but at reduced accuracy. See for product data sheets. 32

36 KMS305W Electromagnetic Wafer Flowmeters with S300 display & output (for corrosive chemicals/acids & slurries) For aggressive chemicals, slurries, oxides, grouts & dosing applications (upto 80% solids). Ceramic liner with Platinum electrodes, K-MAGS Fully wired and custom programmed. Flow sensor sizes 2.5mm to 100mm Wafer connection suites ANSI 150lb flanges Self verifying. Accuracy: ±0.5% vac or vdc powered Totaliser up to 10 digits. With Flowrate display. Integral display or Remote via 2-metres cable to flowsensor. Durable cast alloy display box (integral) or plastic (remote). Pulse and 4-20mA outputs. HART protocol. Programmable via reflective buttons or via HART to PC Built in flow profiler for higher accuracy Self verifying Accuracy: ±0.3% IP68 remote flow sensor (when potted). Empty pipe detection. Pressure rating to 1600 kpa: Process temperature: -10 ºC to 130 ºC Measured liquid must have conductivity of at least 1 µs/cm (20 µs/cm for water) vac powered. Optional vdc. Sizes 2.5mm - 15mm supplied pre-fitted with SST Ground ring (other GR materials available on request) (add -R to code) Flowrange (Litres/min)# Order with with min min max Code Description Integral Display Remote Display (±1%) (±0.3%) (±0.3%) KMS W 2.5 mm, Wafer, Ceramic liner, Platinum electrodes, includes Grounding Rings KMS W 6 mm KMS W 10 mm KMS W 15 mm KMS W 25 mm, Wafer, Ceramic liner, Platinum electrodes, not including Ground Rings KMS W 40 mm, KMS W 50 mm KMS W 80 mm KMS W 100 mm OPTIONS to order, add as suffix to the KMS flowmeter product code -R Remote wired display/transmitter with 2m cable -TRB -DC -VR -XCn Totaliser Reset Button VDC powered Virtual Reference grounding option for IFC300 (instead of grounding rings on corrosive media) Extra cable (in excess of the standard 2 metres), where n in Product Code = extra cable length in metres) # The flowrange is for the stated accuracy. Flowmeter can measure below this flowrange, but at reduced accuracy. See for product data sheets. 33

37 KMS307W Magnetic Wafer Flowmeters with non wetted electrodes for corrosive, abrasive & very low conductive liquids Features of The Ultimate Magflow Solution The Latest Capacitive Mag Technology Unsurpassed performance in the most difficult applications No electrodes in contact with medium meaning:- No Coating, No Wearing and No Corrosion No cleaning or ongoing maintenance required Extremely hard wearing high performance ceramic liner Will work on extremely ultra low conductive liquids Suitable for CIP & SIP cleaning Stable measurement in the noisiest of applications Operation in liquids with up to 70% solids content Typical Applications: Toxic, aggressive & abrasive mediums Abrasive slurries: grouts, cement etc Emulsions including paint & bitumen Water mixed with oil or metallic particles Adhesives Fibrous & high viscos products: molasses, syrup etc Oil-based products: vegetable oils Low conductive liquids: alcohols, spirits, glucols, glycerine etc Dairy products: fat creams, milk, cheese, yoghurt etc Specifications: Flow sensor sizes 25mm to 100mm Ceramic liner with non wetted capacitive electrodes No metals in contact with medium Wafer connection suites ANSI 150lb & TABLE flanges Self-verifying. Accuracy: ±0.5% +/- 5mm/s vac or vdc powered Totaliser up to 10 digits. With Flowrate display. Integral S300 CAP display. Durable die cast aluminium display box (Optional 316 L SST) Pulse and 4-20mA outputs. HART protocol. Programmable via reflective buttons or via HART to PC Empty pipe detection. Pressure rating DN25-80: 4000 kpa, DN100: 1600 kpa Process temperature: -40 ºC to 100 ºC Measured liquid conductivity as low as 0.05 μs/cm or 1 μs/cm in the case of Demineralised water Flowrange (Litres/min) # with min min max Oder Code Description Integral Display (±2%) (±0.5%) (±0.5%) KMS W 25 mm, Wafer, Ceramic liner, non wetted electrodes, with Integral S300 CAP Display, VAC KMS W 40 mm KMS W 50 mm KMS W 80 mm KMS W 100 mm OPTIONS to order, add as suffix to the KMS flowmeter product code -TRB Totaliser Reset Button (mounted at cable gland entry) -DC -VR -316LH VDC powered Virtual Reference grounding option for IFC300 (instead of grounding rings on corrosive media) S300 Display with 316 L Stainless steel housing new Ceramic Liner with non wetted electrodes (capacitive system) KMS307W with Integral Mount S300 CAP Display # The flowrange is for the stated accuracy. Flowmeter can measure below this flowrange, but at reduced accuracy.. - PVC/GAL flanged Connection Kits available Note: These are special meters designed for difficult applications they are not part of our stock inventory therefore must be ordered from the factory with lead time up to 8 weeks. See for product data sheets. 34

38 1.19 CONNECTION KITS for flanged or wafer-style flowmeters CONNECTION KITS - PVC Table D/ANSI-150 QTY 2 x PVC Slip Flange kit. To 1200 kpa (12 bar). With bolts and neoprene gaskets with 316S/S Earth Grounding ring with strap. For all MAGFLOWS KMS (>15mm), MFS, RMS, PMS, FMS flowmeters. supplied already mounted to flowmeter sensor for easy install. CONNECTION KITS - GALVANISED IRON Order Code Size mm Order Code Size mm CK-PVC15 15 FK-GAL15 15 CK-PVC25 25 FK-GAL25 25 CK-PVC40 40 FK-GAL40 40 CK-PVC50 50 FK-GAL50 50 CK-PVC80 80 FK-GAL80 80 CK-PVC FK-GAL CK-PVC e.g. Magflow FK-GAL Table D & E Galvanised Iron Flanged Connection Kits. To 1600 kpa Galvanised Iron threaded BSP(f) entries with neoprene gaskets (earthed to GAL flange). For PMS (>15mm), KMS,, MEH, MFS, RMS, PWMR, SM & WP flowmeters. supplied already mounted to flowmeter for easy install. ANSI-150 QTY 2 x PVC slip flanges with bolts, neoprene gaskets. for all other conventional flowmeter types. To 1200 kpa (12 bar). supplied already mounted to flowmeter for easy install. ANSI-150 Stainless Steel 316 flanges with Steel bolts, neoprene gaskets for flowmeters. To 1600 kpa (16 bar). supplied already mounted to flowmeter for easy install. Order Code Size mm Order Code Size mm FK-PVC15 15 FK-SS15 15 FK-PVC25 25 FK-SS25 25 FK-PVC40 40 Larger sizes available on request FK-PVC50 50 FK-PVC80 80 FK-PVC FK-PVC CAMMLOCKS:- Available on request FK-PVC e.g. Flanged turbine meter Spare EARTH RINGS Stainless Steel Order Code Size mm ER15 15 ER25 25 ER40 40 ER50 50 ER80 80 ER ER See for product data sheets. 35

39 2. BATCH CONTROLLERS 2.1 ME995 Preset Batch Controller series Rotary switch knob selector models Order Code Description Input ppl (1) ME995-1 MILLILITRES 5 digits maximum. 240 vac I/O ME995-1A MILLILITRES 4 digits 9000 maximum 1000 ME995-2 VARIABLE DOSERATE (mls x 10 / m 3 ), CUBIC METRES (Displays mls) 1000 ME995-2H HIGH DOSERATE (mls x 10 / m 3 ), CUBIC METRES (Displays mls) 1000 ME995-2C VARIABLE DOSERATE (mls x 10 / m 3 ), CUBIC METRES (Displays m 3 ) 1000 ME995-2CH HIGH DOSERATE (mls x 10 / m 3 ), CUBIC METRES (Displays m 3 ) 1000 ME995-3 VARIABLE DOSERATE (mls x 10 / 100kg), KG OF CEMENT (Displays mls) 1000 ME995-3H HIGH DOSERATE (mls x 10 / 100kg), KG OF CEMENT (Displays mls) 1000 ME995-3K VARIABLE DOSERATE (mls x 10 / 100kg), KG OF CEMENT (Displays kgs) 1000 ME995-3KH HIGH DOSERATE (mls x 10 / 100kg), KG OF CEMENT (Displays kgs) 1000 ME995-4 LITRES maximum 1000 ME995-6 LITRES 99.9 maximum, with decimal point 1000 ME995-7 LITRES 9999 maximum, with K-factor calibration (x17 multiplier input) (2) ME995-7D LITRES maximum, with decimal point and K-factor calibration x (2) ME995-7D-S LITRES 99.9 maximum, with decimal point and K-factor calibration x (2) ME995-7 ME999 Mult-role batch controller Coming in 2018!! ME999 MLS./LITRES Multi-role programmable batch controller (with USB log) 0.1 to (1) ME995 models with 1000 ppl (pulses per litre) only suitable for use with MES20, AMM15/20 or other flowmeters with 1000 ppl output or 1 millilitre per pulse. (e.g ME995-1). ME995-7, -7D, -7DS models suitable with a larger range of pulse flowmeters e.g. MES25>, RPFS-P, KMS mags. etc. ME999 with any flowmeter 25+ years operational life! ME995-1 ME995-1A ME995-2 Rear View ME995-2C ME995-2CH ME995-3 ME995-3KH ME995-3K ME995-4 ME995-6 ME995-7 ME995-7D-S ME999 See for product data sheets. 36

40 2.2 ME3000 Preset Batch Controller Keypad microprocessor model OrderCode ME3000 Description 6 digit LCD Microprocessor Batch Controller. Panel mount type. Front keypad. IP64. Displays batch in ml / Litres / kl / grams / KG / US Gallons. Flowrate display. Fully programmable e.g. input pulses/litre (K-factor). Batching safety features. 240 vac I/O. With logic, pulse, and current output options. Ticket print quantity is programmable e.g. can print double tickets. NOTE: ME3000 has same plug and dimensions, and is interchangeable with, ME995/ME188. OPTIONS (see also page 38) -SC optional rear RS232 male serial connector for ticket printer output (date/time/batch). Number of batch ticket copies (1 or 2) is user programmable. -FP XC4834 RS232 port on front (includes XC4834 RS232 to USB converter cable), in addition to an RS232 port at back, for easy access to download data to laptop. DB9 Serial to USB converter. SYSTEMS (see Page 47X for more details, and for options / spares / accessories). TMP-DC Batch Printer System. comprises ME3000-SC and TTP-A5 printer, wired and mounted in a hinged lockable powder-coated steel box. with VDC power supply. ME3000 -SC Rear Port -FP Front Port TMP-AC as above, but with 240 vac power supply. TMP-DC TMP Batch Controller Printer PUMP and/or SOLENOID FLOWMETER TMP is ideal for delivery trucks or loading and discharge locations where custody transfer docket is required. Ideal for use with a range of flowmeters e.g. electromagnetic. Example batch ticket. TTP-A5 printer. See for product data sheets. 37

41 2.3 BATCH CONTROLLER PLC INTERFACING and OPTIONS Order Code -MC -MC2 Description Options for ME995 and ME3000 Batch Controllers. To order, add as suffix to Order Code 4-pin PLC external (volt free) command plug set - start, stop, reset. 2-pin plug with OPTO 4N33 open collector pulse output includes 4-pin external command (start, stop, reset) plug for PLCs (specify PLC type when ordering). (1p/1ml. for all models unless stated below, ME995-7D = 1p/0.1Ltr., ME995-7= 1p/1Ltr.) -Sn combined with -MC2, for 10, 20, 50 or 100 ml/pulse output (where n is the pulse value required i.e. 10, 20, 50 or 100). Note: This option is not applicable for the ME3000, because the ME3000 is programmable. -5P 5-pin computer interface plug: start, stop, reset, pulse, +12V. (fitted to ME995 for use with ME5IC interface to PLC/computer e.g. Jonel, COMMANDbatch). -DC-OC VDC power supply input / output drive, with Open Contact output drive (5 Amps) which is via external voltages e.g. 12 or 24 VDC, 110 or 240vac -24VAC 24 vac power supply input / output drive (Neutral can be to Ground or floating) vac power supply input / output drive -OC 240vac supply, Open Contact output drive (5 Amps). Drive is via external voltages e.g. 12 or 24 VDC, 110 or 240vac -SSRBC External command: start, stop, reset, for connection to HB2510-SSR housing box. (is needed for Batch Controller when ordered with HB2510 box). Options for ME995 series Batch Controllers only -S12 switch: two product changeover output drive (ME995 series only). Allows 2 flowmeter-inputs/pump-drives. -SX1-17 x1 - x17 rear switch (for ME995-7 only) for wider range pulse input for flowmeter selection -AO contact output: alarm/batch-complete voltage relay or logic state. TSBC Toggle switch Boot Cover QTY.3 (To increase start/stop/rest/on-off commands to IP65 rating) -MC2 } For -MC2, the output is: } with ME995-7 : 1 L / pulse, } with ME995-7D : 0.1 L / pulse, } otherwise : 1 ml / pulse -5P 5-pin computer interface plug, for use with ME5IC interface cards to COMMANDbatch / Jonel computers. -S12 Two Product Sequential Selection TSBC Toogle boot cover Options for ME3000 Batch Controllers only -OPA Alarm output -OPB Batch Complete output -OPC 4-20mA output PTBS -SC RS232 male serial connector at back of Controller, for ticket printer output (date/time/batch). Trolley batch system -FP RS232 port on front of Controller (includes RS232 to USB converter cable). -PTBS Portable Trolley Batch System wired complete with pump,hoses,enclosure, plug & play use See for product data sheets. 38

42 2.4 Batch Controller Spares Order Code Description BP2 2-pin plug BP4 4-pin plug BP5 5-pin plug FUS Fuse, 5x20mm, 1.25A, 250vac SK Selector knob with cap ST Stator stickers (4 per sheet) W 10-pin Weidmuller plug recepticle BP4 BP5 SK ST W WC WC STV terminal screws insulation clip-on cover to AS3000 (for above W 10-pin receptacle) TS Toggle Switch for ME995 series (start/stop)(test/reset)(on/off) 2.5 INTERFACE CARDS to PLC, for Batch Controllers with Flowmeters Order Code ME5IC-5 ME5IC-1 ME5IC-1W Description 5 channel INTERFACE CARD e.g. ME995-controller/MES20 to Computer PLC, with pulse dividers, 240vac triac optos, start relays, reset relay, 2metres wired comms cable, and 5 pin interface plug (Suits COMMANDbatch or computers using Opto22 yellow case inputs & black case outputs). Note: Batch Controller requires the -5P plug option to connect to ME5IC-5. 1 channel interface card, for 1 admixture. 1 channel interface card, for WATER e.g. use with ME Options -2C Suffix code for any ME5IC card, for 5-30VDC sinking pulse output e.g. for Jonel computer. See the ME5IC datasheet for more I/O voltage options. 2.6 ME6008M Batch Monitor Printer Driver Unit Order Code ME6008M Description Batch Monitor Printer Driver Unit. Monitors up to 8 channels. 240vac powered. For manual batch plants that need QA printout of flowmetered additives or water. Automatic end-of-batch printing and datalogging. Used with serial printers LX-300+II or DP8340. Batch number ID. Real time clock. Grand Total memory and recall. IP65 touchpad. ME6008M-DC As above, but VDC powered. ME6008M1 As above units but 1 channel only used with thermal ticket printer for custody transfers ME6008M -E As above, but with infinity timeout option and Rear PLC log/print command input. -FP RS232 port on front of ME6008M (includes RS232 to USB converter cable), in addition to the RS232 port at the back of ME6008M, for easy access to download data to laptop. LX350 9-pin Impact Dot Matrix printer. 1 line report. 204mm wide printout, 80 characters. fast print speed of up to 357 Characters Per Second (12 CPI). Bi-directional printing. Tractor feed. 128 KB data buffer. Built-in Serial, Parallel and USB Interface. 120 vac, vac powered. LX350 ME5IC-5 ME5IC-1W -FP Front Port See for product data sheets. 39

43 2.7 FIELD ENCLOSURES to house ME995/ME3000 Batch Controllers Order Code HB2510 Description IP65 waterproof polycarbonate single enclosure,with hinged transparent lid cover. With gland kit. New stronger design with 2 stainless steel hinges and clips. Door opens downwards. 200 x 300 x 150 mm -C240W 240vac contactor, internally wired. To drive pump. 4.4kW (up to 8.8 kw on request) -SSR External command: Start, Stop, Reset. IP65. Large push buttons fitted to box # -RWSSR Remote Wand (Start/Stop/Reset) for housing box, with 10 metre lead and plugset # # Note: Must order at the same time as the Housing Box. SHB SHB1 SHB1-T SHB2 DHB DHB2 DHB2-T Single metal housing box (for housing one Batch Controller). Powder coated. Single box, wired with 240vac contactor*, plug-in 240vac pump outlet, and plug. as for SHB1 above, but with terminal wiring entry connection instead of 240vac pump outlet. Single box, wired with 2x 240vac contactors*, 2x plug-in 240vac pump outlet, and plug. Dual metal housing box (for housing two Manu controllers). Powder coated. Dual box, wired with 2x 240vac contactors*, 2x pump outlets, and 2x plugs for Batch Controllers. as for DHB2, but with terminal wiring entry connections (instead of mains lead and pump outlets). -110C 110vac contactor* (instead of 240vac). Option for any housing box. -U Pump outlets and cable entrances mounted UNDERNEATH the housing box, instead of at rear. -RHS Pump outlets and cable entrances mounted on RIGHT HAND SIDE of housing box, instead of rear. * contactor is suitable for 1 hp pumps (4.4 kw standard. Up to 8.8kW on request) HB2510 (shown with Batch Controller) -RWSSR 75BSHB DHB2 HB2500-SSR: waterproof enclosure (shown with Batch Controller) SHB1: Single Housing Box, wired (Front) SHB1-T: Single Housing Box, wired, terminal entry (Front) DHB2: Dual Housing Box wired. SHB1: Single Housing Box, wired (Rear) SHB1-T: Single Housing Box, wired, terminal entry (Rear) See for product data sheets. 40

44 3. PLC/COMPUTER INTERFACE BATCH PRODUCTS 3.1 ME2008/ME2000 Microprocessor safety management interface batching card 7Provides an impressive array of safety features and management systems for flowmetering of Order Code ME liquid admixtures. Inventory management functions. * Manual Batching capability. Description MICROPROCESSOR INTERFACE BATCH SAFETY UNIT. (inbuilt rate +inventory totals) Accepts most flowmeter types. Interfaces with computer/plc systems. Dot-matrix dual LCD counters, 4x plug-in dual-channel modules. 8 channels (8 admixtures) on motherboard, variable pulse divisions, AC triac or DC opto output pulse switching with pulse limiter. Standard unit comes with 240vac supply and start/reset/pulse logic, 240vac pulse output (suits COMMANDbatch etc). Wall mount enclosure. with a hand held plug-in keypad programming module. ME as for ME2008 above, but with plug-in modules for 6 admixures. has 3x dual counter/processor modules (can fit 1 more dual module), in motherboard. ME as for ME2008 above, but with plug-in modules for 4 admixures. has 2x dual counter/processor modules (can fit 2 more dual module), in motherboard. ME Similar to ME2008 above, but motherboard has maximum of 6 channels. has 3x dual counter/processor modules (can t fit more), plugged in to motherboard. ME as for ME2000 above, but with 4 channels (2x dual module) for control of 4 admixtures. ME ME as for ME2000 above, but with 2 channels (1x dual module) for control of 2 admixtures. ME CV as above, but ADMIX COMPACT VERSION. 2 channels only (no expansion). Box size (mm) : 225 L x 180 W x 90 D ME2002-CV-W As above, with WATER BATCHING Software suits water flowmeters (high volume).. -CV To order, must also choose one option from EACH of the following three groups: Supply Voltage (Motherboard) -1A 240 vac power supply See next page -1B 110 vac power supply for ME2008-1C 24 vac power supply expansion/spares -1D 24 VDC power supply Start Input/Output Drives and Master Reset (Modules) -2A 240 vac start/reset relay logic fitted -2B 110 vac start/reset relay logic fitted -2C 24 vac start/reset relay logic fitted -2D 24 VDC start/reset relay logic fitted Pulse output -3A 240 vac (Moc3041) triac pulse output switching (only with -1A 240v power supply option) New!! -3B Same ac voltage as for the start/reset option (i.e 24 vac or 110 vac) ME channel LCD unit -3C 5-30 VDC open collector pulse output. Suits Jonel/Compubatch/Autocon computers. Coming in 2019 e.g. for COMMANDbatch computer, order ME A-2A-3A; for Jonel-Archer computer, order ME A-2A-3C; for all DC computer i/o, order ME D-2D-3C. See for product data sheets. 41

45 3.1.1 ME2008/ME2000 Microprocessor safety management interface batching card (options / spares) Options Description 6CAT5E For 6-channel ME2000: 3-way external panel, for programming up to 3 dual-ch modules. (Includes HP-CAT5E programmer with CAT5E plug only when ordered with a ME2000). 8CAT5E For 8-channel ME2008: 4-way external panel, for programming up to 4 dual ch modules. (Includes HP-CAT5E programmer with CAT5E plug - only when ordered with a ME2008). -IR Independent Reset, per 2-channel module in the ME USoz USA units (non-metric) - Display in US ounces -V1.8 Software version IC to enable/disable the display/comparator function (replacement/upgrade). -AO Alarm logic output. Open contact relay. WSC Wima suppression capacitors, with long leads. 0.1µF, 275 volts (placed across contactor coils) RP10 5watt 12K ceramic resistors (for possible leakvoltage suppression for 240vac optos) 1pack of 10 4N33 IC: 5-30 VDC white OPTO (for U3 & U4 sockets of ME2000/2008, for DC pulse output) MOC3043 IC: vac Triac OPTO (for U1 & U2 sockets of ME2000/2008, for ac pulse output) 4-way 8CAT5E with included HP-CAT5E programmer ME2008/ME2000 Expansion / Spares Order Code DCPM HP HP-CAT5E HK SS SPK WH10 DCPM-W Description Extra dual-channel module, expand ME2000 or ME2008 (specify the I/O config., ac/dc etc) Spare hand held plug-in keypad programming module, for ME2000 or ME2008. As above but Programmer with CAT5E plug Spare Hinge kit for ME2000/08 Spare Springed Screw Spare rear I/O connection plugs kit complete Wiring harness kit, to parallel flowmeter pulses from an ME2000 or ME2008 and connect to ME6008M 8-channel Batch Monitor Printer Driver Unit (see section 0). Dual Channel module with WATER BATCHING software V1.9, plug-in module for ME2000/2008.Suits interface of most flowmeters to the PLC/computer batching system. (specify the I/O config., ac/dc etc)(for higher volume batching of water) 3.2 UIC Flowmeter Interface Pulse Scaler Card DCPM HP Order Code UIC/A2 UIC/A1 UIC/D -24DC Description UNIVERSAL INTERFACE CARD with pulse scaling (flowmeter to PLC input) vac triac switching pulse output, and 5-12 VDC sink pulse output. Heavy duty. High isolation. x10 input scaling VDC powered. similar to UIC/A2, but vac lower current pulse switching via triac opto. UNIVERSAL INTERFACE CARD with pulse scaling (flowmeter to PLC input) 5-30 VDC open collector 4N33 opto-isolated pulse output and 5-12 VDC sink output VDC powered. option: 24 VDC powered (instead of 5-12 VDC) with 12VDC supply to flowmeter. UIC/A2 Widely used with MES-P and MagFlow flowmeters for interfacing to PLC batching computers See for product data sheets. 42

46 4. SYSTEMS Note: a range of products from this catalogue can be mixed and matched to form systems. 4.1 Slump Stand Systems Order Code DSSS-1 Description Dual - Slump Stand / Batch Room water measurement system package wired: 1x ME5-T-D batchroom counter, 12-24VDC powered, DC pulse output. 1x MRTU4-P int.bat.pwr. flowmeter with integral reset total display and pulse output via M12 Ip67 plug-set 2mtr lead, 1x GAL25-T2 pipe fitting. OPTIONS:- -A 240vac powered ME5-T counter (in lieu of DC pwr). NOTE:- Use shielded cable for the pulse cable run to batchroom. KM W -R -DC Option for Heavy Recycled Water used on slumpstands; 25 mm Magflow with resettable total + rate display, Wafer sensor, Polyp.liner, Hast- C electrodes vac (range LPM) Remote wired display version via 2mtr cable 11-30VDC Powered option MRTU4-GAL25-T2 SLUMPSTAND FLOWMETER ONLY 25mm Resettable LCD insertion Battery powered Flowmeter (1 bsp-m galvanised pipe connection ends) MRTU4-GAL25-T2 -P Pulse output option via M12 plug-set. (for future pulse transmission) NEW! ME6 Batchroom 6-channel Totaliser Display with master reset + outputs for Multiple Systems Order Code Description ME6T-AC 6-channel x 8-digit LCD counter - IDEAL MULTPLE SLUMPSTAND SYSTEMS 1 pulse = 1 count, 1 pulse/ 1 Litre flowmeter pulse inputs, display is in Litres Single Master reset facility.,240 vac powered OPTIONS:- ME6T-DC as above, but 24 VDC powered, instead of 240vac powered Example only -PDC 5-30VDC pulse outputs for 5-24VDC PLC inputs, opto isolated via 4n33 -PAC 240vac pulse outputs for 240vac PLC inputs ME6T See for product data sheets. 43

47 4.1.2 WPTR Wireless Live pulse transmission / reciever systems Description WPTR Wireless Pulse Transmitter/Receiver system (ideal for slumpstands) PACKAGE. Compact design. Includes 2x antennas for transmitter/reciever. RECIEVER unit with 2 inputs: 12-24VDC powered. 2 x PLS outputs, panel mount type. TRANSMITTER unit 1 output: VDC powered., in IP65 enclosure. 150 metre maximum transmission distance, 5 Hz maximum LIVE pulse (Pulse rule: 1p/1ltr = 5 litres/sec max. flowrate) WPTR Transmitters WPTR-R Reciever Simply connect pulse output of flowmeter to input of transmitter. Connect output of receiver to display device, UIC-card or PLC input. For batch plants where running cables from slumpstand to batchroom is not viable. WP-T WP-R -AC OPTIONS / EXTRAS / KIT BUILDS:- 1-channel wireless pulse transmitter only in IP65 encl VDC pwr. 2-channel wireless pulse receiver only, panel mount type, 12-24vdc pwr. Transmitter as 240 vac powered option ME5-T-D-P ME5-T-A-P UIC Resettable batchroom counter +DC output with 24VDC pwr (24vdc pwr for rec.) Resettable batchroom counter +DC output with 240vac pwr (12vdc pwr for rec.) Universal interface for PLC inputs (-D for 5-25VDC)(-A2 for vac) MRTU4-P- GAL25-T2 25mm Resettable LCD insertion Battery powered Flowmeter Prefitted and calibrated on 1 GAL tee keyway pipe adaptor (1 bsp-m) Pulse output option via M12 plug-set for slumpstands System:- MRTU4-P-GAL25-T2 / WPTR / ME5T-D-P NOTE: Multipe Expansion of systems available in 2,4,6 & 8 channels / flowmeters SYSTEM EXPANSION EXAMPLE:- 2 x flowmeters to transmit from 2 slump bays to batchroom direct to 24VDC PLC 2 x MRTU4-P-GAL25-T2 25mm flowmeters. 2 x WP-T transmitters 12-24vdc pwr, in separate IP65 boxes 1 x WP-R dual (2) input receiver 12-24vdc pwr, panel mount. 3 x Antenas included. 2 x ME5-T-D-P, 5-24vdc pwr reset total counters with pulse out 2 x UIC/D pulse isolation scaler cards See for product data sheets. 44

48 4.2 Dosing Low Flowrates Chemicals Order Code KMS104P-006F MM series Description 6mm precision electromagnetic Wafer flowmeter for dosing applications 4-20mA control output., digital pulse output, Ideal for cement plants. flowrange: Litres/minute ( Litres/hour ) vac powered or VDC pwr. (other sizes available) 4mm to 25mm compact electromagnetic flowmeters for dosing or batch applications with LED display. M12 connection 4-20mA output., digital pulse output, flowrange: Litres/hour VDC powered Optionally:-4mm RMS004-M4 Flowrange: LPH) Or 8mm RMS008-M4 Flowrange: LPH) KMS RMS MM 4.3 Shotcrete Admixture Flowmeters Order Code KMS104F- 015F-DC-TRB Description 15mm electromagnetic flowmeter, for Shotcrete admixture. Integral display shows flowrate and resettable Total VDC powered. ANSI-150 flanged, Hastelloy-C4 electrodes, PTFE liner. ±2% accuracy: Litres/minute. to 2000 kpa (20 bar) pulse and 4-20mA outputs -R Remote display via 2-metres cable shows flowrate & resettable total SCS-MM15 Shotcrete Admix System complete. 24VDC powered. (or 12VDC with 12-24VDC step-up voltage converter) Includes FRT303-D-E-BL-VR24 Flowrate/Totaliser Indicator with backlit LCD display and regulated 24VDC output to MM15 ½ BSP (male) electromagnetic flowmeter to 1600 kpa (16 bar) ±2% accuracy: Litres/min), and -SSB Stainless Steel outer enclosure all wired with 5-metre cable to flowmeter and 1 metre power cord. OPTIONS: 20mm -MM20 ( LPM) or 25mm -MM25 ( LPM) flowmeters. NOTE: Other budget cost options available on application SCS-MM15 See for product data sheets. 45

49 4.4 Grout / Oxide / Slurry Flowmeters (for measuring liquids upto 80% solids) Order Code KMS302P- 025F Description 25mm electromagnetic flowmeter, for liquid Grout/Oxide/Slurry mixes. Integral display shows Flowrate and resettable Total vac powered. ANSI-150 flanged, Hast-C4 electrodes, PolyProp liner. ±2% accuracy: Litres/minute. Larger sizes available RMS025-M4 25mm WAFER HIGH PRESSURE OPTION To 5100kPa (740 Psi) Options:- -R remote display version also available -TRB Totaliser reset button -DC VDC powered, instead of ac powered KMS RMS High Pressure Wafer 4.5 Concrete Plant Admix/Water Batch Systems Order Code Description MWBS Classic Concrete Plant Water Batch System: ME995-7 Batch Controller, RPFS-P flow sensor, GAL50 pipe adapter OR create your own system by purchasing components seperately: Batch Controller panel mount type.with optional housing enclosures Options for interfaces to PLC flow sensor insertion RPFS-P type with various pipe size adapters Magflow type for recycle / slurry water add solenoid valves Typical batching installation Water Storage Tank tank valve Batch Controller RPFS-P flow sensor, and GAL50 pipe adapter Solenoid 4.6 Concrete Batch Plant Admix System Kit Batch Controller: order ME995 model of your choice, to suit Batch Controller Housing Box: order SHB, DHB, HB2500 options to suit Flowmeters: order MES or MM flowmeter to suit. Pump: order pump to suit Ancillary Kit - consisting of: gate valve, non-return valve, sleves, elbows, unions & camlocks. Cable: order length of cable from flowmeter to Batch Controller. KIT PACKAGE ORDER CODE ITEM # AK2520 See for product data sheets. 46

50 4.7 TMP Auto Batching Custody Transfer Ticket Printer System (used primarily with electromagnetic flowmeters) Contains: ME3000 Batch Controller ( or soon with optional ME999 ) o 6 digit LCD Microprocessor Batch Controller. Panel mount. IP64. o Front keypad. Displays in ml / L / kl / Gal with decimal point. o Number of batch ticket copies is user programmable. o Fully programmable functions. With logic, pulse, and current output options. o with RS232 serial connector for ticket printer output (date/time/batch). TTP-A5 o thermal ticket printer, with power supply. o for cusody transfer dockets. all wired and mounted in a IP64 hinged lockable powder-coated steel box. Order Code TMP-DC TMP-AC Description ME3000 Batch Controller and TTP-A5 printer Fully wired and mounted in a hinged lockable box VDC powered. ME3000 Batch Controller and TTP-A5 printer Fully wired and mounted in a hinged lockable box. 240vac powered Optional -FP Optional front RS232 port, so batch log can be downloaded to a laptop. Includes DB9 serial to USB converter for laptops without a serial port. -ESS Stainless Steel 316 enclosure, instead of powder coated (300mm W x 400mm H x 200mm D). -USG Display in US Gallons and 110vac powered system UPS-DC Uninterruptable Power Supply. 24VDC to 14.5 VDC. 4.5 Ah, 3hrs 1.5A UPS-AC Uninterruptable Power Supply. 240VAC to 14.5 VDC. 4.5 Ah, 3hrs 1.5A SPARES/ACCESSORIES T-TP50 Thermal Paper for TTP-A5 thermal ticket printer (box of 50 rolls) T-TP Thermal Paper for TTP-A5 thermal ticket printer (single roll) 57 x 46mm (52g) TTP-A5 Thermal Ticket Printer baud. 5-9 VDC powered. suitable for cusody transfer dockets for ME3000-SC. without power supply (power supply is separate item, see below) T-ACPS T-DCPS AC power supply module for TTP-A5 printer. Input: 240vac, output: 5VDC. 3 Amp. DC power supply module for TTP-A5 printer. Input: 12-24VDC, output: 5VDC. 3 Amp. ME3000 / ME VAC > 5VDC -FP Front Port See for product data sheets. 47 UPS-DC 12/24VDC > 5VDC TMP TMP PUMP and/or SOLENOID Batch Controller Printer FLOWMETER Ideal with a range of flowmeters e.g. MFS50 Example batch ticket TTP-A5 ticket printer

51 4.8 TMP-1 Manual Batching Custody Transfer Docket Printer System (single channel) For manual batching. Ideal for delivery trucks or loading and discharge locations where a custody transfer docket is required. At the end of each manual batch, the TMP-1 (after a settable period of wait time if there is no activity i.e. flow of liquid stops) automatically provides batch quantity printout with date, time and Batch ID. Number of batch ticket copies is user programmable. Front keypad. Displays in ml / L / Gal with decimal point. Contains: ME6008M1 1-channel Batch Monitor Printer Driver Unit, with optional front serial port to download internal log of 500 batches to a laptop. TTP-A5 thermal docket printer, with power supply. all wired and mounted in a IP64 hinged lockable powder-coated steel box (300mm W x 300mm H x 200mm D). TMP-1 Order Code Description TMP-1 TMP-1-DC ME6008M1 1-channel Batch Monitor Printer Driver Unit and TTP-A5 printer, fully wired and mounted in a hinged lockable box VDC powered. TMP-1-AC As above, but 240vac powered TMP As above, but 110vac powered Optional -FP Optional front RS232 port, so batch log can be downloaded to a laptop. Includes DB9 serial to USB converter for laptops without a serial port. -FP Front Port -ESS Stainless Steel 316 enclosure, instead of powder coated (300mm W x 400mm H x 200mm D). UPS-DC Uninterruptable Power Supply. 24VDC to 14.5 VDC. 4.5 Ah, 3hrs 1.5A UPS-AC Uninterruptable Power Supply. 240VAC to 14.5 VDC. 4.5 Ah, 3hrs 1.5A SPARES/ACCESSORIES T-TP50 Thermal Paper for TTP-A5 thermal ticket printer (box of 50 rolls) T-TP Thermal Paper for TTP-A5 thermal ticket printer (single roll) 57 x 46mm (52g) TTP-A5 Thermal Ticket Printer baud. 5-9 VDC powered. suitable for cusody transfer dockets for ME6008M1. without power supply (power supply is separate item, see below) T-ACPS AC power supply module for TTP-A5 printer. Input: 240vac, output: 5VDC. 3 Amp. T-DCPS DC power supply module for TTP-A5 printer. Input: 12-24VDC, output: 5VDC. 3 Amp. ME6008M1 1-channel Batch Monitor Printer Driver Unit (specify voltage when ordering) TTP-A5 ticket printer See for product data sheets. 48 Batch Monitor Printer FLOWMETER Ideal with a range of flowmeters e.g. KMS50, MES40 example batch ticket 240VAC > 5VDC 12/24VDC > 5VDC

52 5.0 Pressure Measurement Systems 5.1 OPTIBAR - New Pressure Sensors with ATEX, IECEx certificates PC5060-C range (ideal for Grout/Slurries) Robust ceramic diaphragm Reference accuracy up to +/-0.05% Process temperatures up to 150 C / 302 F 4..20mA/HART, Profibus PA, Foundation Fieldbus new PM5060-C range High pressure ranges up to 1000bar / psi Reference accuracy up to +/-0.075% Process temperatures up to 150 C / 302 F 4..20mA/HART, Profibus PA, Foundation Fieldbus P3060-C range Compact pressure transmitter with recessed diaphragm Optional display and adjustment module Reference accuracy +/- 0.1% Adjustment of Zero/Span also without display Two-wire mA PM5060-C PC5060-C P3060-C Order Code PC5060-C PM5060-C P3060-C Description Specification details on application Specifications details on application Specifications details on application See for product data sheets. 49

53 6. FILTERS, ELECTRICAL ACCESSORIES and SOLENOID VALVES 6.1 Filters. Y-strainer cartridge type. Order Code Description (Recommended for positive displacement flowmeters) A20/300 A20/800 20mm Polyprop. Y-strainer Filter, with 800 micron nylon filter cartridge ¾ BSP-m A20/300 20mm Polyprop. Y-strainer Filter, with 300 micron nylon filter cartridge ¾ BSP-m FC-XXX SPARE Filter Cartridge, FC micron for MES20, FC micron for MEA15 HRT20/400 HRT25/400 HRT40/400 Check Valves ACV20 ACV25 20mm Plastic, Y-strainer Filter with 400 micron filter cartridge ¾ BSP-F swivel connection 25mm Plastic, Y-strainer Filter with 400 micron filter cartridge 1 BSP-F swivel connection 40mm Plastic, Y-strainer Filter with 400 micron filter cartridge 1½ BSP-F swivel connection SPARE Filters cartridges available HRT-FC20, HRT-FC25, HRT-FC40 20mm check valve. Polypropelene. Spring loaded. BSP (female) threaded. 25mm check valve. Polypropelene. Spring loaded. BSP (female) threaded. Cartridge Check Valve 6.2 Electrical accessories contactors, signal cable and power supplies Order Code Description C240 Contactor GE N.O. 240vac 2 line, 4kW rating, industrial grade. (Ideal for isolation between ManuFlo controllers and 1 h.p. 1" single phase pump motor units) W3020 Signal cable, light duty, 2-core wire braid screen shielded - 100m roll. AWG27 W3040 Signal cable, light duty, 4-core wire braid screen shielded - 100m roll. AWG27 W3028 Signal cable, heavy duty, 2-core wire braid screen shielded - 100m roll. AWG24 W3029 Signal cable, heavy duty, 2-core wire braid screen shielded - 300m roll. AWG24 WB-1575 Signal cable, light duty, 6-core screened - 100m roll WB-1578 Signal cable, light duty, 9-core screened - 100m roll D-IP 24 VDC reg.pwr. supply pack, 240 vac source, 2 Amp in IP65 box ideal for DC Magflows C240 Contactor W3028 cable CV12 12>24VDC DC12 12 VDC reg.pwr. supply pack, 240 vac source, upto 500 ma [ MP-3011 ] VDC reg.pwr. supply pack, 240 vac source, 1A.,IP65 ENCLOSURE. ideal for UIC cards CV12 12 VDC to 24 VDC power stepup converter. 2 Amp. -Ideal for flowmeters CV24 24 VDC to 12 VDC power converter module. 3 Amp. ENC IP65 enclosure, 120x95x60mm. Ideal for housing UIC cards, and used for FRT303 and ME D 240 vac input to 24 VDC regulated output. DIN rail. 2.5 Amps -for DC Magflows (MP3192) DC JB Junction Box IP65 rated 2way PG9 glanded entry (ideal for linking cables) See for product data sheets. 50

54 6.3 Solenoid Control Valves - Metal Order Code Description Solenoid Valves - To order, must also specify the coil voltage option. Require 0.3 Bar min. pressure to operate. Up to 20 bar rating. BSP(f) thread connections. Standard seals are NBR. D15 15mm BRASS Diaphram solenoid valve with 6.8 W electric control coil N.C. D15 D20 20mm D25 25mm D32 32mm For water and light chemicals D40 40mm (i.e. not thick or acidic). D50 50mm Electric powered, no air assist. Order Code Description Angle Seat Valves, 0 to 16 bar, BSP(f) threaded connection, air assisted. AS15 15mm Angle Seat BRONZE solenoid valve with electric coil (normally closed), NBR seals. AS20 20mm AS25 25mm AS32 32mm AS40 40mm AS50 50mm Other seal options available. AS50 For Admix or water. Air assisted. Quick acting. OPTIONS for the Dxx, DSxx, ASxx and ASxxS Solenoid Control Valve ranges. 6.8 W -12D Coil voltage 12VDC -24D Coil voltage 24VDC -24A Coil voltage 24 vac -110A Coil voltage 110 vac -240A Coil voltage 240 vac -MOR Manual override button Order Code Description B50 Cast-iron wafer Butterfly Valve. Double acting. Air assisted for fast operation. N.C. For bulk water B50 50mm Butterfly Valve, 240vac pilot valve and speed restrictor e.g. in Batch Plant. B80 80mm Air Assist. Fast B mm acting. SPARES COIL-XXX Coil for solenoid (XXX being the nominated voltage). SOL Solenoid for above valves Other types of solenoid ball-valves and materials (e.g. Stainless Steel) are available. See for product data sheets. 51

55 7. PUMPS Order Code Size Type Description Power supply Watts Packed Weight kg Carton Dimensions mm ONGA413 1 Onga 413 Single phase centrifugal pump 1/2hp, <15mtr, to 120LPM 240vac x 190 x 260 SJ Davey SJ35-04 Single phase centrifugal pump. 240vac IP55 motor rpm. 2.3 Amps. To 80 Litres/min. Head height up to 25 metres. XF171-S 1 Davey XF171-S Single phase centrifugal pump, Silicon Carbide seals, <17mtrs 240vac Davey SJ-35 Series Pumps ideal for low cost delivery of water-based admixtures built to cover a wide range of commercial, rural and domestic applications. suitable for pumping clean nonaggressive liquids without solids or fibres in suspension. strong and durable. manufactured from molded materials giving superior resistance to corrosion. SS304 Efficient design produces greater flow whilst maintaining low power consumption. 8. Optional Connectors, Gate Valves and Check Valves Order Code SBU15 Connectors for MES, MM and AMM Series Flowmeters Description 15 mm Barrel Unions (Pair, QTY 2). BSP female ends. Polypropylene. SBU20 20 mm SBU25 25 mm SBU32 32 mm SBU40 40 mm SBU50 50 mm T15GV Manual Gate Valves and Spring Check Valves ½ Gate Valve. BSP (female). Multi-turn. Brass. T20GV ¾ T25GV 1 15BSCV ½ Spring Check Valve. BSP (female). In-line. Brass. 20BSCV ¾ 25BSCV 1 various Camlock fittings available in Aluminium or Polypropelyne Maximum working pressure : 410 kpa Water temperature range : 1 50 C Maximum Ambient temperature : 55 C Motor type: TEFC 2 Pole Continuously rated. Nominal speed: 2900 rpm IP rating: IP55 See for product data sheets. 52