INSTALL GUIDE FLC-FO(RS)-FO1B-[FLRSFO1]-EN

Transcription

1 INSTALL GUIDE DOUMENT NUMER REVISION DATE 00 FIRMWARE FL-FO(RS)-FO-[FLRSFO] HARDWARE FLRSFO AESSORIES FLPROG (REQUIRED) FLRF// (OPTIONAL) ARLINK ASL (OPTIONAL) TERMS OF USE: Automotive Data Solutions Inc. ( ADS ) products are strictly intended for installation by ertified Technicians who are employed by a registered business specialized in the installation of automotive aftermarket electronics products. Prior to beginning installation of an ADS product in a vehicle, it is the ertified Technician s responsibility to review the most current Product Guide, Install Guide and vehicle-specific notes available in Weblink. ADS is not responsible for any damages whatsoever, including but not limited to any consequential damages, incidental damages, damages for loss of time, loss of earnings, loss of profit, commercial loss, loss of economic opportunity and the like that may or may not have resulted from the use, misuse, improper installation or operation of its products. ADS reserves itself the right to suspend any Weblink account without notice and decline to offer technical support to non-ertified Technicians, non-compliant ertified Technicians or end users. EFORE INSTALLATION - onnect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)

2 VEHILE LIST - OF PAGE OF FEATURES MAKE MODEL YEAR INSTALL TYPE DATA IMMOILIZER YPASS X LOK START/STANDALONE MOD. DOOR LOK DOOR UNLOK FORD ARM OEM ALARM LINOLN DISARM OEM ALARM POWER LIFTGATE TRUNK/HATH RELEASE RAP SHUTDOWN TRL HOOD STATUS (W/OEM SW) DOOR STATUS RAKE PEDAL STATUS TAHOMETER STATUS GLOW PLUGS STATUS PARKING LIGHT TRL Edge STD key AT - Expedition STD key AT - Explorer STD key AT - F-0 STD key AT - F-Super Duty STD key AT - Fiesta STD key AT - Flex STD key AT - Taurus STD key AT - Transit STD key AT* - MKX STD key AT - *Aftermarket RF kit required to control remote start.

3 OX ONTENTS - OF PAGE OF OX ONTENTS T-HARNESS 0 PIN ONNETOR VS LUE LAK LAK A LED LED G F E D PROGRAMMING UTTON 0 LAK RF PORT/ WELINK PORT LUE TELEMATI PORT LAK WHITE MS MS VS VS VS PIN ONNETOR AFTERMARKET HOOD SWITH AND ALE WARNING STIKER WELINK ALE (required accessory sold separately) WELINK ALE WELINK PORT OMPUTER US PORT PIN LAK ALE

4 OMPATILE AESSORIES - OF PAGE OF DO.: # 00 RF KIT (accessories sold separately) FLRF// RF KIT RF PORT (N) ANTENNA TELEMATI KIT (accessories sold separately) FLHRNTM ARLINK TELEMATI PORT (N) TELEMATI KIT (accessories sold separately) FLHRNTM PN 00 AR ONNETION ODII ONNETOR TELEMATI PORT (N) VEHILE ODII PORT 0

5 OMPONENT LOATOR - OF PAGE OF INTERIOR VIEW F A G H D E DRIVER SIDE VIEW PASSENGER SIDE VIEW

6 TYPE - WIRE HART - OF PAGE OF FORD MAKE MODEL YEAR WIRE DESRIPTION ONNETOR NAME ONNETOR OLOR ONNETOR TYPE POSITION WIRE OLOR LINOLN POLARITY LOATION OMPONENT LOATOR Edge STD key AT Explorer STD key AT MKX STD key AT anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple/Green (-) M, driver side dash H Driver Door Pin 0 lack pin 0 Green/Purple (OPEN) M, driver side dash H Lock 0 lack pin 0 lue/green (-) M, driver side dash H Unlock 0 lack pin 0 Yellow/Purple (-) M, driver side dash H Trunk Release lack 0 pin 0 Gray/Yellow (-) At liftgate switch in glovebox D Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, driver side dash H anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple/Green (-) M, driver side dash H Driver Door Pin 0 lack pin 0 Green/Purple (OPEN) M, driver side dash H Lock 0 lack pin 0 lue/green (-) M, driver side dash H Unlock 0 lack pin 0 Yellow/Purple (-) M, driver side dash H Trunk Release lack 0 pin 0 Gray/Yellow (-) At liftgate switch on driver side dash A Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, driver side dash H anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple/Green (-) M, driver side dash H Driver Door Pin 0 lack pin 0 Green/Purple (OPEN) M, driver side dash H Lock 0 lack pin 0 lue/green (-) M, driver side dash H Unlock 0 lack pin 0 Yellow/Purple (-) M, driver side dash H Trunk Release lack 0 pin 0 Gray/Yellow (-) At liftgate switch in glovebox D Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, driver side dash H

7 TYPE - WIRING DIAGRAM - OF PAGE OF IGNITION SWITH (UNDER STEERING OLUMN) VS A G F E D RF PORT/WELINK PORT TELEMATI PORT VS IMMOILIZER ONNETOR IMMOILIZER HARNESS VS A IGNITION ONNETOR MS VS IGNITION HARNESS ODII 0 0 MS ROWN/RED ROWN/YELLOW GREEN/WHITE GREEN/PURPLE ANH - 0 ANL - DRIVER DOOR PIN (OPEN) - 0 LOK (-) - 0 UNLOK (-) LAK 0 M (DRIVER SIDE DASH) ROWN/LAK - PARKING LIGHT (-) OUTPUT 0 GRAY (N) 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOK (-) OUTPUT 0 EMPTY 0 LUE/GREEN - TRUNK (-) OUTPUT 0 EMPTY 0 EMPTY GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOK (-) OUTPUT OPTIONAL * SEE NEXT PAGE FOR WIRE ONNETION A 0 0 AMPS HORN (-) - PARKING LIGHT (+) - 0 V (+) 0 LAK 0E GRAY E 0

8 TYPE - WIRING DIAGRAM - OF PAGE OF A G F E D RF PORT/WELINK PORT TELEMATI PORT - LAK LIFTGATE SWITH 0 0 ROWN/LAK - PARKING LIGHT (-) OUTPUT 0 GRAY (N) 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOK (-) OUTPUT 0 EMPTY 0 LUE/GREEN - TRUNK (-) OUTPUT 0 EMPTY 0 EMPTY GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOK (-) OUTPUT * SEE PREVIOUS PAGE FOR WIRE ONNETION * SEE PREVIOUS PAGE FOR WIRE ONNETION * SEE PREVIOUS PAGE FOR WIRE ONNETION REFER TO WIRE HART TRUNK RELEASE (-) OR - LAK D 0 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITH: INSTALL AND ONNET TO AFTERMARKET HOOD SWITH AFTERMARKET HOOD SWITH (-)

9 TYPE - WIRE HART - OF PAGE OF MAKE MODEL YEAR FORD WIRE DESRIPTION ONNETOR NAME ONNETOR OLOR ONNETOR TYPE POSITION WIRE OLOR POLARITY LOATION OMPONENT LOATOR anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple (-) M, passenger kick panel E Driver Door Pin 0 lack pin 0 Green/Purple (OPEN) M, passenger kick panel E Expedition Lock 0 lack pin 0 White/rown (-) M, passenger kick panel E - STD key AT Unlock 0 lack pin 0 lue/rown (-) M, passenger kick panel E Trunk Release ~ lack 0 pin 0 Gray/Yellow (-) At liftgate switch Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, passenger kick panel E Auto Light 0 Gray 0 pin 0 Purple/Green (OPEN) Headlight switch A Light Off 0 Gray 0 pin 0 White/Purple (-) Headlight switch A anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple/Green (-) M, passenger side dash E Driver Door Pin 0 lack pin 0 Green/Purple (OPEN) M, passenger side dash* E F-0 Lock 0 lack pin 0 lue/green (-) M, passenger side dash* E - STD key AT Unlock 0 lack pin 0 Yellow/Purple (-) M, passenger side dash* E Trunk Release ~ ~ ~ ~ ~ ~ ~ ~ Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, passenger side dash E Auto Light 0 Gray 0 pin 0 Purple/Green (OPEN) Headlight switch A Light Off 0 Gray 0 pin 0 White/Purple (-) Headlight switch A anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple/Green (-) M, passenger side dash E Driver Door Pin 0 lack pin 0 Green/Purple (OPEN) M, passenger side dash* E F-Super Duty Lock 0 lack pin 0 lue/green (-) M, passenger side dash* E - STD key AT Unlock 0 lack pin 0 Yellow/Purple (-) M, passenger side dash* E Trunk Release ~ ~ ~ ~ ~ ~ ~ ~ Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, passenger side dash E Auto Light 0 Gray 0 pin 0 Purple/Green (OPEN) Headlight switch A Light Off 0 Gray 0 pin 0 White/Purple (-) Headlight switch A * Wire also found in driver door harness.

10 TYPE - WIRE HART - OF PAGE 0 OF MAKE MODEL YEAR WIRE DESRIPTION ONNETOR NAME ONNETOR OLOR ONNETOR TYPE FORD POSITION WIRE OLOR POLARITY LOATION OMPONENT LOATOR Flex STD key AT Taurus STD key AT - - anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple/Green (-) M, driver side dash Driver Door Pin 0 lack pin 0 Purple (OPEN) M, driver side dash Lock 0 lack pin 0 lue (-) M, driver side dash Unlock 0 lack pin 0 Yellow (-) M, driver side dash Trunk Release lack 0 pin 0 Gray (-) At liftgate switch on driver side dash A Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, driver side dash Auto Light 0 Gray 0 pin 0 Purple/Green (OPEN) Headlight switch A Light Off 0 Gray 0 pin 0 White/Purple (-) Headlight switch A anh lack pin 0 Gray/Orange (DATA) ODII connector G anl lack pin Purple/Orange (DATA) ODII connector G Horn 0 lack pin Purple/Green (-) M, driver side dash Driver Door Pin 0 lack pin 0 Green/Purple (OPEN) M, driver side dash Lock 0 lack pin 0 lue/green (-) M, driver side dash Unlock 0 lack pin 0 Yellow/Purple (-) M, driver side dash Trunk Release lack 0 pin 0 rown (-) At trunk release switch on center console Parking Light 0E Gray 0 pin 0 Yellow/lue (+) M, driver side dash Auto Light 0 Gray 0 pin 0 Purple/Green or Purple (OPEN) Headlight switch A Light Off 0 Gray 0 pin 0 White/Purple or White (-) Headlight switch A

11 TYPE - WIRING DIAGRAM - OF PAGE OF IGNITION SWITH (UNDER STEERING OLUMN) VS A G F E D RF PORT/WELINK PORT TELEMATI PORT VS IMMOILIZER ONNETOR IMMOILIZER HARNESS VS A MS VS IGNITION ONNETOR IGNITION HARNESS M (DRIVER SIDE DASH) 0 0 MS GREEN/WHITE GREEN/PURPLE * SEE NEXT PAGE FOR WIRE ONNETION OPTIONAL DRIVER DOOR PIN (OPEN) - 0 LOK (-) - 0 UNLOK (-) - 0 HORN (-) - 0 LAK 0 LAK * SEE NEXT PAGE FOR WIRE ONNETION ROWN/LAK - PARKING LIGHT (-) OUTPUT 0 GRAY (N) 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOK (-) OUTPUT 0 EMPTY 0 LUE/GREEN - TRUNK (-) OUTPUT 0 EMPTY 0 EMPTY GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOK (-) OUTPUT OR WITHOUT AUTO LIGHT WITH AUTO LIGHT A 0 0 AMPS V (+) PARKING LIGHT (+) - 0 PARKING LIGHT (+) - 0 0E GRAY 0 0 0E A 0 A 0 0 AMPS V (+) 0 PARKING LIGHT SWITH DIODE N00 LIGHT (-) - 0 AUTO LIGHT (OPEN) GRAY 0

12 TYPE - WIRING DIAGRAM - OF PAGE OF A G F E D RF PORT/WELINK PORT TELEMATI PORT 0 0 MS * SEE PREVIOUS PAGE FOR WIRE ONNETION ROWN/RED ROWN/YELLOW ANH - 0 ANL - ODII ROWN/LAK - PARKING LIGHT (-) OUTPUT 0 GRAY (N) 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOK (-) OUTPUT 0 EMPTY 0 LUE/GREEN - TRUNK (-) OUTPUT 0 EMPTY 0 EMPTY GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOK (-) OUTPUT * SEE PREVIOUS PAGE FOR WIRE ONNETION * SEE PREVIOUS PAGE FOR WIRE ONNETION * SEE PREVIOUS PAGE FOR WIRE ONNETION TRUNK/LIFTGATE RELEASE (-) - 0 REFER TO WIRE HART TRUNK/LIFTGATE SWITH - LAK D 0 0 GRAY/LAK (N) 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITH: INSTALL AND ONNET TO AFTERMARKET HOOD SWITH AFTERMARKET HOOD SWITH (-)

13 TYPE - WIRE HART - OF PAGE OF MAKE MODEL YEAR WIRE DESRIPTION FORD ONNETOR NAME ONNETOR OLOR ONNETOR TYPE POSITION WIRE OLOR POLARITY LOATION OMPONENT LOATOR anh lack pin 0 Gray/Orange (DATA) ODII connector anl lack pin Purple/Orange (DATA) ODII connector Driver Door Pin 0G Gray pin Green/Purple (OPEN) M, behind glove box D Fiesta STD key AT - Horn 0E Green pin 0 rown (-) M, behind glove box D Light 0 Gray 0 pin 0 White/Purple (-) Headlight switch A Lock 0F White pin 0 rown/white (-) M, behind glove box D Parking Light 0 Gray 0 pin 0 Yellow/lue (-) Headlight switch A Trunk Release 0G Gray pin 0 Green/White (-) M, behind glove box D Unlock 0G Gray pin 0 lue/rown (-) M, behind glove box D Disarm 0G Gray pin 0 Purple/rown (-) M, behind glove box D

14 TYPE - WIRING DIAGRAM - OF PAGE OF IGNITION SWITH (UNDER STEERING OLUMN) VS A G F E D RF PORT/WELINK PORT TELEMATI PORT VS IMMOILIZER ONNETOR IMMOILIZER HARNESS VS A MS VS IGNITION ONNETOR IGNITION HARNESS M (EHIND GLOVE OX) 0 0 MS GREEN/WHITE GREEN/PURPLE * SEE NEXT PAGE FOR WIRE ONNETION DIODE N00 DIODE N00 DRIVER DOOR PIN (OPEN) - TRUNK RELEASE (-) - 0 UNLOK (-) - 0 DISARM (-) - 0 LOK (-) - 0 (0G) GRAY (0F) WHITE ROWN/LAK - PARKING LIGHT (-) OUTPUT 0 GRAY (N) 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOK (-) OUTPUT 0 EMPTY 0 LUE/GREEN - TRUNK/LIFTGATE (-) OUTPUT 0 EMPTY 0 EMPTY GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOK (-) OUTPUT OPTIONAL HORN (-) - 0 (0E) GREEN 0 0 A 0 AMP V (+) PARKING LIGHT SWITH DIODE N00 LIGHT (-) - 0 PARKING LIGHT (-) GRAY 0

15 TYPE - WIRING DIAGRAM - OF PAGE OF A G F E D RF PORT/WELINK PORT TELEMATI PORT 0 0 MS * SEE PREVIOUS PAGE FOR WIRE ONNETION ROWN/RED ROWN/YELLOW ANH - 0 ANL - ODII 0 D 0 0 GRAY/WHITE - HOOD STATUS (-) INPUT WITHOUT OEM HOOD SWITH: INSTALL AND ONNET TO AFTERMARKET HOOD SWITH AFTERMARKET HOOD SWITH (-)

16 TYPE - WIRE HART - OF PAGE OF MAKE MODEL YEAR WIRE DESRIPTION FORD ONNETOR NAME ONNETOR OLOR ONNETOR TYPE POSITION WIRE OLOR POLARITY LOATION OMPONENT LOATOR anh White pin 0 Gray/Orange (DATA) ODII connector G anl White pin Purple/Orange (DATA) ODII connector G Horn A Yellow pin 0 lue/white (-) Steering lock connector, bottom of steering column G Transit STD key AT - Driver Door Pin 0 rown pin Green/Purple (OPEN) M, driver side dash A Lock 0 rown pin Gray/Yellow (-) M, driver side dash A Unlock 0 rown pin Purple/Gray (-) M, driver side dash A Parking Light (front left) 0 rown pin Green/Orange (+) M, driver side dash A Parking Light (rear left) 0 rown pin Purple/Green (+) M, driver side dash A Parking Light (front right) 0 rown pin rown/yellow (+) M, driver side dash A Parking Light (rear right) 0 rown pin White/Orange (+) M, driver side dash A

17 TYPE - WIRING DIAGRAM - OF PAGE OF A G F E D RF PORT/WELINK PORT TELEMATI PORT VS VS VS IMMOILIZER ONNETOR IMMOILIZER HARNESS IGNITION ONNETOR IGNITION SWITH (UNDER STEERING OLUMN) A MS VS IGNITION HARNESS ODII D MS 0 ROWN/LAK - PARKING LIGHT (-) OUTPUT 0 GRAY (N) 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN - LOK (-) OUTPUT 0 EMPTY 0 LUE/GREEN (N) 0 EMPTY 0 EMPTY GRAY/GREEN - HORN (-) OUTPUT DKGREEN/GREEN - UNLOK (-) OUTPUT 0 GRAY/WHITE - HOOD STATUS (-) INPUT A 0 ROWN/RED ROWN/YELLOW GREEN/WHITE GREEN/PURPLE AMPS DIODE N00 AMPS DIODE N00 AMPS DIODE N00 AMPS DIODE N00 AMPS ANH - 0 ANL - DRIVER DOOR PIN (OPEN) - LOK (-) - UNLOK (-) - PARKING LIGHT FRONT RIGHT (+) - PARKING LIGHT REAR RIGHT (+) - PARKING LIGHT FRONT LEFT (+) - PARKING LIGHT REAR LEFT (+) - 0 ROWN 0 ROWN M (DRIVER SIDE DASH) 0 0 WITHOUT OEM HOOD SWITH: INSTALL AND ONNET TO AFTERMARKET HOOD SWITH V (+) STEERING LOK ONNETOR (OTTOM OF STEERING OLUMN) OPTIONAL AFTERMARKET HOOD SWITH (-) HORN (-) - 0 A YELLOW

18 PROGRAMMING PROEDURE ( KEYS) - OF PAGE OF >> NOTE: To complete this procedure, both OEM keys are required. 0 Wait, LED will turn. (This may take up to 0 seconds) A ON START Insert key into ignition. 0 A ON START Insert key into ignition. 0 A ON START Insert key into ignition. A ON START Turn key to ON position. 0 A ON START Turn key to ON position. LED will turn solid RED. 0 A ON START Turn key to ON position. Wait, LED will turn solid RED then will turn. 0 LED will flash GREEN. 0 If LED turns solid GREEN for seconds: Module Programming Procedure completed. If LED turns solid RED, proceed with following step. TIME RESTRITION. omplete steps and within seconds after LED turns. 0 A ON START Turn key to position. 0 TIME RESTRITION. omplete steps 0 to 0 within seconds after LED turns. A ON START Remove key. 0 Remove key. Remove key. Press and release programming button. A ON START A ON START

19 PROGRAMMING PROEDURE ( KEYS) - OF PAGE OF >> If the LED begins to flash RED, you are using a cloned key or used the same key twice. Wait, LED will turn solid RED then will turn solid GREEN. Module Programming Procedure completed.

20 VALET MODE PROGRAMMING PROEDURE - OF PAGE 0 OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. >> To exit valet mode: repeat steps to. 0 Time restriction. omplete next step within seconds. 0 A ON START ycle ignition ON five times [x /ON] rapidly. ENGINE START STOP 0 Wait, LED will turn solid RED for seconds. 0 A ON START Set ignition to position. ENGINE START STOP 0 Valet Mode Programming Procedure completed.

21 AFTERMARKET REMOTE PROGRAMMING - OF PAGE OF AFTERMARKET REMOTE PROGRAMMING: NOTES I All aftermarket remotes must be programmed to the RF-Kit. Refer to the RF-Kit user guide for aftermarket remote features and programming procedures.

22 PAGE OF NAVIGATION PROEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation hart on the next page. 0 Set ignition to position. 0 TO AESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 0 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 0 0 A ON START DO.: # 00 TO AESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO AESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. onfigure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT NAVIGATION. Press and hold programming button for seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X]

23 NAVIGATION HART - OF PAGE OF NAVIGATION HART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS I II Default settings are listed in bold. Make sure the option is covered on the vehicle before attempting to change the setting. *Vehicle will shutdown when a door is opened. 0 ONFIGURATION 0 DISARM/UNLOK EFORE START 0 0 ON 0 RELOK AFTER START 0 0 ON 0 RELOK AFTER SHUTDOWN 0 0 ON 0 FORE UNLOK ALL ON FIRST PRESS 0 0 ON 0 TAKEOVER 0 ENALE 0 DISALE* 0 N/A 0 N/A 0 DISALE 0 FATORY KEYLESS RS SEQUENE 0 N/A 0 LOK + UNLOK + LOK 0 LOK + LOK + LOK 0 0 MIN 0 0 MIN 0 0 MIN 0 RUN TIME 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 SE 0 0 SE 0 0 SE 0 WAIT TO START DELAY 0 0 SE 0 SE 0 0 SE 0 SE 0 0 SE 0 N/A 0 N/A N/A 0 N/A N/A 0 N/A N/A 0 N/A

24 NAVIGATION HART - OF PAGE OF NAVIGATION HART: NOTES [X] MENUS [Y] OPTIONS [Z] SETTINGS *Vehicle will shutdown when a door is opened. 0 DOULE LOK HORN EVENT TRIGGER 0 LOK + UNLOK 0 LOK + UNLOK + START 0 ONFIGURATION 0 DOULE LOK + START 0 0 mse HORN HIRPS WIDTH 0 msec 0 0 msec 0-0 Technical Support only 0 N/A 0 N/A

25 REMOTE STARTER ERROR ODES - OF PAGE OF REMOTE STARTER ERROR ODES: NOTES [X] NUMER OF PARKING LIGHT FLASHES DIAGNOSTI I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Foot brake is ON. 0 Hood is open. 0 Engine tach signal is lost. 0 System is in Valet Mode. 0 Vehicle is moving (VSS). 0 Glow plug timeout error. 0 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. 0 N/A N/A N/A N/A N/A N/A AN communication failure during RS sequence.

26 DIAGNOSTIS - OF PAGE OF TEST LED STATUS DIAGNOSTI I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Flashing RED Solid RED Flashing GREEN Solid GREEN then Missing/wrong information from firmware or vehicle. Module waiting for more vehicle information. Additional steps required to complete module programming. Module correctly programmed. No activity or module already programmed. Module incorrectly programmed. Module incorrectly programmed. Module correctly programmed and operational. Reset in progress. Invalid ground when running status from remote starter. Module incorrectly programmed or connected. Module not programmed. Waiting for more vehicle information. False ground when running status from remote starter. Reset in progress. Module at rest and ready for a remote start sequence.

27 RESET PROEDURE - OF PAGE OF 0 Disconnect all connectors from module except the LAK 0-PIN connector. 0 Reconnect all connectors. 0 Disconnect the LAK 0-PIN connector. 0 Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the LAK 0-PIN connector. >> Failure to follow procedure may result with a DT or a HEK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed.

28 INSTALLATION HEKLIST - OF PAGE OF WARNING: Vehicle engine will start many times. Test in a well ventilated area. lose all vehicle doors, hood and trunk. Press the LOK button once [x] on the aftermarket keyfob. Question : Do the doors lock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the UNLOK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question : Does the trunk or hatch open/unlock? YES: lose trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Question : Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Question : Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. HEKLIST Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. 0 RAP and auto light shutdown test Question : Did the radio, interior controls and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. lose hood. Enter vehicle and close the doors. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Wait for the vehicle to start. Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. Exit vehicle. 0 Installation checklist completed.