idatastart HC Document number Revision Date

Transcription

1 PRODUCT guide idatastart HC Document number Revision Date 0503 NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 05

2 GETTING ED Page of WeLcome Congratulations on the purchase of your idatastart HC solution. You are now a few simple steps away from enjoying your new remote starter unit with enhanced features. Before starting your installation, please ensure that your idatastart HC module is programmed with the correct firmware for your vehicle and that you carefully review the install guide. table of contents Box Contents 3 Module Pinout 4 Tach Programming Procedure 5 Remote Programming Procedure 6 Valet Mode Programming Procedure 7 Compatible Accessories 9 Online Module Settings 0 Module Diagnostics Remote Starter Error Codes need HeLP? Module Reset Procedure support@idatalink.com idatalink.com/support Automotive Data Solutions Inc. 05 idatastart HC

3 BOX CTENTS - OF Page 3 of BOX CTENTS HC MODULE -WAY REMOTE - TR350AC HC - HC35AC M - 8 PIN BLACK AUTOMATIC TRANSMISSI CUT LOOP M - PIN BLACK M3-0 PIN WHITE TELEMATIC - 4 PIN BLUE TELEMATIC - 4 PIN RED NC - 4 PIN RED M5-6 PIN BLUE M4-0 PIN BLACK NC - 3 PIN BLACK PROGRAMMING BUTT -WAY REMOTE - TR50A HC - HC35AC LED LED RF PORT/WEBLINK PORT - 4 PIN BLACK USB ANTENNA - AN300A ANTENNA CABLE HC - HC5AC ANTENNA LED HOOD SWITCH M5 M4 M3 M M ANTENNA BUTT HCF - HCF900A RF PORT - 4 PIN BLACK RF DECODER - FT-D00 RF DECODER CABLE PIN BLACK RF PORT - 4 PIN BLACK HCX - HCX000A STICKERS 6 PIN WHITE OR BLUE ANTENNA RF PORT - 4 PIN WHITE Automotive Data Solutions Inc. 05 idatastart HC

4 MODULE PINOUT - OF Page 4 of HC MODULE M 0 ORANGE - ESSORY (+) 0 RED - POWER (30A) 03 PURPLE - ER (+) 04 PINK/WHITE - PROG. RELAY #4 - IGNITI (+) (DEFAULT) 05 PINK - IGNITI (+) 06 WHITE - PROG. RELAY #5 (0A) - PARKING LIGHTS (+) (DEFAULT) 07 RED - POWER (30A) 08 BLACK - GROUND M M 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT - TRUNK RELEASE (-) OUTPUT 04 GREEN/WHITE BLACK DOT - ARM (-) OUTPUT 05 GREEN/BLACK BLACK DOT - DISARM (-) OUTPUT 06 BLUE/WHITE BLACK DOT - GWR (-) OUTPUT 07 EMPTY 08 WHITE/PURPLE BLACK DOT - POC - ND UNLOCK OTHER DOORS (-) OUTPUT 09 PURPLE/BLACK BLACK DOT - POC - RAP SHUTDOWN (-) OUTPUT 0 WHITE/BLACK BLACK DOT - POC 3 - HORN (-) OUTPUT BROWN/BLACK BLACK DOT - POC 4 - ER KILL (-) OUTPUT WHITE BLACK DOT - PARKING LIGHTS (-) OUTPUT AUTOMATIC TRANSMISSI CUT LOOP M M3 M5 M M3 0 BROWN SILVER DOT - BRAKE (+) INPUT 0 BLACK/WHITE SILVER DOT - E-BRAKE (-) INPUT 03 PURPLE SILVER DOT - DOOR (+) INPUT 04 GREEN SILVER DOT - DOOR (-) INPUT 05 PURPLE/WHITE SILVER DOT - TACH (-) INPUT 06 WHITE/BLUE SILVER DOT - X-TRIGGER (-) INPUT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT - TRUNK (-) INPUT 09 GRAY/BLACK SILVER DOT - GLOW PLUG (+) INPUT 0 EMPTY M FUNCTIS DEFINED BY FIRMWARE M FUNCTIS DEFINED BY FIRMWARE Automotive Data Solutions Inc. 05 idatastart HC

5 TACH PROGRAMMING PROCEDURE - OF Page 5 of vehicle for 5 seconds. ENGINE STOP 0 Press and hold the brake pedal. 03 Press and release the module s programming button. (OR if the remotes are already programmed to the vehicle, press and hold the start button of the remote for.5 seconds.) 04 Wait, LED will flash GREEN. (See the Module Diagnostics page) 05 Release the brake pedal. 06 Module Programming Procedure completed. Automotive Data Solutions Inc. 05 idatastart HC

6 REMOTE PROGRAMMING PROCEDURE - OF Page 6 of [4x] WARNING: Complete the module programming procedure and tach programming procedure before programming the remotes. A maximum of four [4x] remotes per system. 07 Release the antenna button. The antenna s leds will turn. 0 Set ignition to position. 08 Set ignition to position. ENGINE STOP ENGINE STOP 03 Press and release the antenna button, then press and hold the antenna button. The antenna s leds will turn solid BLUE. 09 Remote Programming Procedure completed Parking Light will flash once [x]. Press once [x] on the LOCK button of each remote. >> F To program an additional remote as second vehicle mode: Follow steps to 4. Press twice [x] on the F button then press once [x] on the LOCK button of the remote. Follow steps 6 to The antenna s leds will flash BLUE once [x] for each successful pairing. Automotive Data Solutions Inc. 05 idatastart HC

7 VALET MODE PROGRAMMING PROCEDURE - OF Page 7 of >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. 06 Valet Mode Programming Procedure completed. 0 Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps to 5. 0 Cycle ignition twice [x /] rapidly. ENGINE STOP 03 Press and release the BRAKE pedal three times [3x]. 04 Parking Light will flash once [x] then will flash twice [x]. 05 Set ignition to position. ENGINE STOP Automotive Data Solutions Inc. 05 idatastart HC

8 COMPATIBLE ESSORIES - OF Page 8 of WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT 4 PIN BLACK CABLE WEBLINK MOBILE (accessory sold separately) OBDII CNECTOR MODULE WEBLINK PORT 4 PIN BLACK CABLE MOBILE DEVICE PORT OBDII CNECTOR TELEMATIC KIT (accessory sold separately) MODULE TELEMATIC BLUE PORT (NC) *For SmartStart, use the module s RED Telematic port. Automotive Data Solutions Inc. 05 idatastart HC

9 COMPATIBLE ESSORIES - OF Page 9 of RF DECODER (included with the HCF) RF KIT (sold separately) MODULE RF PORT RF DECODER - FT-D00 (NC) RED (NC) BLACK BLACK BLUE or WHITE RF KIT FLASH THE DECODER BEFORE THE INSTALLATI BLUE CABLE DECODER BLACK CABLE ANTENNA RF KIT (included with the HC & HC) MODULE RF PORT 4 PIN BLACK CABLE ANTENNA Automotive Data Solutions Inc. 05 idatastart HC

10 online MoDULe SeTTINgS - OF Page 0 of WeB PRogRaMMaBLe MeNUS MENU Remote Starter MENU Doorlock Options MENU 3 Security Options MENU 4 AUX function assignments MENU 5 Programmable outputs (POC) MENU 6 Pulse Timer Output Configuration (PTO) MENU 7 Input Configurations MENU 8 Output Configurations Programming options are avaible through Weblink and Weblink Mobile only. DeSCRIPTIoN RS related configuration options Convenience feature configuration options Alarm activation and settings Set transmitter AUX buttons controls Set actions for programmable outputs Set duration for pulse timer outputs (if used) Set inputs for Auto by firmware/data/analog Set outputs for Auto by firmware/data/analog Automotive Data Solutions Inc. 05 idatastart HC

11 MoDULe DIagNoSTICS - OF Page of TeST MoDULe LeD STaTUS DIagNoSTIC I II III IV DURING MODULE PROGRAMMING DURING TACH PROGRAMMING DURING REMOTE WITH IGNITI Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. GREEN flash Tach signal programmed in Analog GREEN flashes Tach signal programmed in Data 3 RED flashes No tach signal detected 4 RED flashes System is in valet mode 5 RED flashes Tach set for VTS. No tach programming required 6 RED flashes Tach set for assumed start. No tach programming required Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. Automotive Data Solutions Inc. 05 idatastart HC

12 ReMoTe STaRTeR error CoDeS - OF Page of ReMoTe STaRTeR error CoDeS: NoTeS [X] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. After a remote starter failure, the parking lights will flash three [3x] times, then will flash [X] number times to indicate an error code. See table. 0 Engine running. 0 Key in ignition at position. 03 Door is open. 04 Trunk is open. 05 Foot brake is. 06 Hood is open. 07 The reservation is. (Manual transmission only) 08 Tach failure. 09 The vehicle is moving (VSS). 0 System is in Valet Mode. CAN communication failure RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Bypass problem. ReMoTe STaRTeR SHUTDoWN error CoDeS: NoTeS [Y] NUMBeR of PaRKINg LIgHT flashes DIagNoSTIC I II WARNING: The following applies only when the parking lights are connected and supported by the system. If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for.5 seconds when using a -WAY remote. OR Press once [x] on button 4 when using a -WAY remote. The parking lights will flash four [4x] times, then will flash [Y] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 Emergency brake is lost. 03 Foot brake is. 04 Hood is open. 05 Engine RPM limiter is. 06 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 N/A 09 N/A 0 Door is open. CAN communication failure during RS sequence. RS not synchronized. Start vehicle with OEM key for 5 sec before trying a new RS sequence. 3 Takeover is not allowed. 4 Shutdown error, board overheat protection. Automotive Data Solutions Inc. 05 idatastart HC

13 MODULE RESET PROCEDURE - OF Page 3 of >> The following procedure resets the module programming to the vehicle. It does not reset any settings configured online. 06 Module RESET completed. 0 Disconnect all connectors from module except the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. 07 Reconnect all connectors. 0 Disconnect the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. 08 Repeat programming procedure. 03 PRESS AND HOLD the module s programming button while connecting the M BLACK 8-pin connector and the M4 BLACK 0-pin connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 04 Wait, LED will flash RED. RELEASE programming button. 05 LED will turn RED for seconds. Automotive Data Solutions Inc. 05 idatastart HC

14 INSTALL GUIDE Mitsubishi Eclipse STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

15 HARDWIRE / COMPENT LOCATOR - OF PAGE OF B A D C E 03A_v_[W] Automotive Data Solutions Inc Mitsubishi Eclipse STD key AT

16 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M! M M3 M M M3 M5 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE - ESSORY (+) 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY DO NOT CNECT DISARM. DO NOT PROGRAM UNLOCK BEFORE. 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY V (+) BLUE/YELLOW - 0 IGNITI (+) RED - 0 ESSORY (+) BLUE/RED - 04 ER (+) BLACK/YELLOW - 05 ESSORY (+) BLUE/BLACK - 06 DRIVER DOOR PIN (-) LTGREEN - 06 CANH (DATA) RED - 06 CANL (DATA) BLACK - 4 LOCK (-) PURPLE UNLOCK (-) GREEN/RED : BLUE IGNITI SWITCH (A) JUNCTI BOX (B) OBDII (C) HARNESS FROM DRIVER DOOR (D) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK PARKING LIGHT (+) GREEN/ORANGE DRIVER SIDE RUNNING BOARD (E) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 03A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Eclipse STD key AT

17 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Eclipse STD key AT

18 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Eclipse STD key AT

19 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Eclipse STD key AT

20 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Eclipse STD key AT

21 INSTALL GUIDE Mitsubishi Eclipse Spyder STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

22 HARDWIRE / COMPENT LOCATOR - OF PAGE OF B A D C E 03A_v_[W] Automotive Data Solutions Inc Mitsubishi Eclipse Spyder STD key AT

23 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M! M M3 M M M3 M5 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE - ESSORY (+) 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY DO NOT CNECT DISARM. DO NOT PROGRAM UNLOCK BEFORE. 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY V (+) BLUE/YELLOW - 0 IGNITI (+) RED - 0 ESSORY (+) BLUE/RED - 04 ER (+) BLACK/YELLOW - 05 ESSORY (+) BLUE/BLACK - 06 DRIVER DOOR PIN (-) LTGREEN - 06 CANH (DATA) RED - 06 CANL (DATA) BLACK - 4 LOCK (-) PURPLE UNLOCK (-) GREEN/RED : BLUE IGNITI SWITCH (A) JUNCTI BOX (B) OBDII (C) HARNESS FROM DRIVER DOOR (D) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK PARKING LIGHT (+) GREEN/ORANGE DRIVER SIDE RUNNING BOARD (E) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 03A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Eclipse Spyder STD key AT

24 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Eclipse Spyder STD key AT

25 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Eclipse Spyder STD key AT

26 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Eclipse Spyder STD key AT

27 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Eclipse Spyder STD key AT

28 INSTALL GUIDE Mitsubishi Endeavor STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

29 HARDWIRE / COMPENT LOCATOR - OF PAGE OF B A D C E 03B_v_[W] Automotive Data Solutions Inc Mitsubishi Endeavor STD key AT

30 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M! M M3 M M M3 M5 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE - ESSORY (+) 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY DO NOT CNECT DISARM. DO NOT PROGRAM UNLOCK BEFORE. 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY V (+) BLUE/YELLOW - 0 IGNITI (+) BLACK/WHITE - 0 ESSORY (+) BLUE/RED - 04 ER (+) BLACK/YELLOW - 05 ESSORY (+) BLUE/BLACK - 06 DRIVER DOOR PIN (-) LTGREEN - 06 CANH (DATA) RED - 06 CANL (DATA) BLACK - 4 LOCK (-) PURPLE UNLOCK (-) GREEN/RED : BLUE IGNITI SWITCH (A) JUNCTI BOX (B) OBDII (C) HARNESS FROM DRIVER DOOR (D) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK PARKING LIGHT (+) GREEN/ORANGE DRIVER SIDE RUNNING BOARD (E) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 03B_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Endeavor STD key AT

31 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Endeavor STD key AT

32 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Endeavor STD key AT

33 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Endeavor STD key AT

34 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Endeavor STD key AT

35 INSTALL GUIDE Mitsubishi Galant STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

36 HARDWIRE / COMPENT LOCATOR - OF PAGE OF B A D C E 03B_v_[W] Automotive Data Solutions Inc Mitsubishi Galant STD key AT

37 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M! M M3 M M M3 M5 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE - ESSORY (+) 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND! CUT LOOP FOR AUTOMATIC TRANSMISSI LY DO NOT CNECT DISARM. DO NOT PROGRAM UNLOCK BEFORE. 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY V (+) BLUE/YELLOW - 0 IGNITI (+) BLACK/WHITE - 0 ESSORY (+) BLUE/RED - 04 ER (+) BLACK/YELLOW - 05 ESSORY (+) BLUE/BLACK - 06 DRIVER DOOR PIN (-) LTGREEN - 06 CANH (DATA) RED - 06 CANL (DATA) BLACK - 4 LOCK (-) PURPLE UNLOCK (-) GREEN/RED : BLUE IGNITI SWITCH (A) JUNCTI BOX (B) OBDII (C) HARNESS FROM DRIVER DOOR (D) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK PARKING LIGHT (+) GREEN/ORANGE DRIVER SIDE RUNNING BOARD (E) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 03B_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Galant STD key AT

38 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Galant STD key AT

39 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Galant STD key AT

40 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Galant STD key AT

41 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Galant STD key AT

42 INSTALL GUIDE Mitsubishi Lancer Evo STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

43 HARDWIRE / COMPENT LOCATOR - OF PAGE OF C A B 0B_v_[W] Automotive Data Solutions Inc Mitsubishi Lancer Evo STD key AT

44 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND M M3 M4 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A CANH (DATA) WHITE/BLUE OR YELLOW - 08 CANL (DATA) BLACK/BLUE OR LTGREEN - 09 V (+) WHITE OR BLACK/RED - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 : BLACK/WHITE : BLACK 3 9 : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0B_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Lancer Evo STD key AT

45 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Lancer Evo STD key AT

46 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Lancer Evo STD key AT

47 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Evo STD key AT

48 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Evo STD key AT

49 INSTALL GUIDE Mitsubishi Lancer Evo Fast-Key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

50 HARDWIRE / COMPENT LOCATOR - OF PAGE OF C A B 0A_v_[W] Automotive Data Solutions Inc Mitsubishi Lancer Evo Fast-Key AT

51 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M M M3 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - TUMBLER SENSE (+) CNECTOR SIDE GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A TUMBLER SENSE (+) GREEN - 0 CANH (DATA) WHITE/BLUE OR YELLOW - 08 CANL (DATA) BLACK/BLUE OR LTGREEN - 09 V (+) WHITE OR BLACK/RED - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 : BLACK/WHITE : BLACK : BLACK/WHITE : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - TUMBLER SENSE (+) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - TUMBLER SENSE (+) CNECTOR SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Lancer Evo Fast-Key AT

52 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Fast-key must be inside the vehicle. 07 Press and release the module s programming button. 0 Set ignition to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Set ignition to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Lancer Evo Fast-Key AT

53 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Lancer Evo Fast-Key AT

54 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Evo Fast-Key AT

55 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Evo Fast-Key AT

56 INSTALL GUIDE Mitsubishi Lancer Fast-Key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

57 HARDWIRE / COMPENT LOCATOR - OF PAGE OF C A B 0A_v_[W] Automotive Data Solutions Inc Mitsubishi Lancer Fast-Key AT

58 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M M M3 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - TUMBLER SENSE (+) CNECTOR SIDE GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A TUMBLER SENSE (+) GREEN - 08 CANH (DATA) WHITE/BLUE OR YELLOW - 08 CANL (DATA) BLACK/BLUE OR LTGREEN - 09 V (+) WHITE OR BLACK/RED - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 : BLACK/WHITE : BLACK : BLACK/WHITE : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - TUMBLER SENSE (+) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - TUMBLER SENSE (+) CNECTOR SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Lancer Fast-Key AT

59 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Fast-key must be inside the vehicle. 07 Press and release the module s programming button. 0 Set ignition to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Set ignition to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Lancer Fast-Key AT

60 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Lancer Fast-Key AT

61 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Fast-Key AT

62 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Fast-Key AT

63 INSTALL GUIDE Mitsubishi Lancer Ralliart Fast-Key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

64 HARDWIRE / COMPENT LOCATOR - OF PAGE OF C A B 0A_v_[W] Automotive Data Solutions Inc Mitsubishi Lancer Ralliart Fast-Key AT

65 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M M M3 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - TUMBLER SENSE (+) CNECTOR SIDE GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A TUMBLER SENSE (+) GREEN - 08 CANH (DATA) WHITE/BLUE OR YELLOW - 08 CANL (DATA) BLACK/BLUE OR LTGREEN - 09 V (+) WHITE OR BLACK/RED - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 : BLACK/WHITE : BLACK : BLACK/WHITE : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT - TUMBLER SENSE (+) VEHICLE SIDE 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT - TUMBLER SENSE (+) CNECTOR SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Lancer Ralliart Fast-Key AT

66 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Fast-key must be inside the vehicle. 07 Press and release the module s programming button. 0 Set ignition to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Set ignition to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart Fast-Key AT

67 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart Fast-Key AT

68 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart Fast-Key AT

69 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart Fast-Key AT

70 INSTALL GUIDE Mitsubishi Lancer Ralliart STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

71 HARDWIRE / COMPENT LOCATOR - OF PAGE OF C A B 0A_v_[W] Automotive Data Solutions Inc Mitsubishi Lancer Ralliart STD key AT

72 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND M M3 M4 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A CANH (DATA) WHITE/BLUE OR YELLOW - 08 CANL (DATA) BLACK/BLUE OR LTGREEN - 09 V (+) WHITE OR BLACK/RED - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 : BLACK/WHITE : BLACK 3 9 : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Lancer Ralliart STD key AT

73 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart STD key AT

74 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart STD key AT

75 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart STD key AT

76 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer Ralliart STD key AT

77 INSTALL GUIDE Mitsubishi Lancer STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

78 HARDWIRE / COMPENT LOCATOR - OF PAGE OF C A B 0A_v_[W] Automotive Data Solutions Inc Mitsubishi Lancer STD key AT

79 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND M M3 M4 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A CANH (DATA) WHITE/BLUE OR YELLOW - 08 CANL (DATA) BLACK/BLUE OR LTGREEN - 09 V (+) WHITE OR BLACK/RED - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 : BLACK/WHITE : BLACK 3 9 : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Lancer STD key AT

80 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Lancer STD key AT

81 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Lancer STD key AT

82 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer STD key AT

83 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Lancer STD key AT

84 INSTALL GUIDE Mitsubishi Mirage STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

85 HARDWIRE / COMPENT LOCATOR - OF PAGE OF B A C D 07A_v_[W] Automotive Data Solutions Inc Mitsubishi Mirage STD key AT

86 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M! M M3 M5 M4! CUT LOOP FOR AUTOMATIC TRANSMISSI LY V (+) WHITE - 0 IGNITI (+) GREEN - 0 : WHITE IGNITI SWITCH (A) M 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND ESSORY (+) YELLOW - 04 ER (+) PINK : WHITE 3 ETACS/ECU (B) M 0 GREEN BLACK DOT - LOCK (-) OUTPUT 0 BLUE BLACK DOT - UNLOCK (-) OUTPUT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT UNLOCK (-) BLUE - LOCK (-) GREEN M3 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY PARKING LIGHT (+) GREEN - 0 CANH (DATA) BROWN - 06 C-405: WHITE OBDII (C) M4 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - DRIVER DOOR PIN (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK CANL (DATA) BLACK - 4 DRIVER DOOR PIN (-) PURPLE : WHITE PIN DRIVER KICK PANEL (D) M5 0 GRAY/BLACK BLUE DOT 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 07A_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Mirage STD key AT

87 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Mirage STD key AT

88 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Mirage STD key AT

89 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Mirage STD key AT

90 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Mirage STD key AT

91 INSTALL GUIDE Mitsubishi Outlander Fast-Key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

92 HARDWIRE / COMPENT LOCATOR - OF PAGE OF D C A B 0B_v_[W] Automotive Data Solutions Inc Mitsubishi Outlander Fast-Key AT

93 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M M M3 M4 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED - TUMBLER SENSE (+) CNECTOR SIDE GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A TUMBLER SENSE (+) GREEN - 0 CANH (DATA) YELLOW - 08 CANL (DATA) LTGREEN - 09 V (+) WHITE - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 ALARM SENSOR (DATA) PURPLE - 0 APPLY LY IF VEHICLE IS EQUIPPED WITH PROXIMITY SENSOR : BLACK/WHITE : BLACK : BLACK/WHITE : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) 3 0 OVERHEAD CSOLE, NEAR RADAR SENSOR (D) 3 M5 0 GRAY/BLACK BLUE DOT - ALARM SENSOR (DATA) VEHICLE SIDE 0 WHITE/BLACK BLUE DOT - TUMBLER SENSE (+) VEHICLE SIDE 03 GRAY/RED BLUE DOT - ALARM SENSOR (DATA) CNECTOR SIDE 04 WHITE/RED BLUE DOT - TUMBLER SENSE (+) CNECTOR SIDE 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0B_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Outlander Fast-Key AT

94 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Fast-key must be inside the vehicle. 07 Press and release the module s programming button. 0 Set ignition to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Set ignition to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Outlander Fast-Key AT

95 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Outlander Fast-Key AT

96 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Outlander Fast-Key AT

97 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Outlander Fast-Key AT

98 INSTALL GUIDE Mitsubishi Outlander STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06

99 HARDWIRE / COMPENT LOCATOR - OF PAGE OF D C A B 0C_v_[W] Automotive Data Solutions Inc Mitsubishi Outlander STD key AT

100 HARDWIRE / WIRING DIAGRAM - OF PAGE 3 OF M!! CUT LOOP FOR AUTOMATIC TRANSMISSI LY LEFT SIDE OF STEERING COLUMN (A) M M3 M5 M4 IGNITI (+) WHITE - 0 : WHITE ESSORY (+) LTGREEN - 04 ER (+) ORANGE M 0 ORANGE - ESSORY (+) 0 RED - VOLT (+) 03 PURPLE - ER (+) 04 PINK/WHITE 05 PINK - IGNITI (+) 06 WHITE - PARKING LIGHT (+) 07 RED - V (+) 08 BLACK - GROUND M M3 M4 0 GREEN BLACK DOT 0 BLUE BLACK DOT 03 RED/WHITE BLACK DOT 04 GREEN/WHITE BLACK DOT 05 GREEN/BLACK BLACK DOT 06 BLUE/WHITE BLACK DOT 07 EMPTY 08 WHITE/PURPLE BLACK DOT 09 PURPLE/BLACK BLACK DOT 0 WHITE/BLACK BLACK DOT - HORN (-) OUTPUT BROWN/BLACK BLACK DOT WHITE BLACK DOT 0 BROWN SILVER DOT 0 BLACK/WHITE SILVER DOT 03 PURPLE SILVER DOT 04 GREEN SILVER DOT 05 PURPLE/WHITE SILVER DOT 06 WHITE/BLUE SILVER DOT 07 GRAY SILVER DOT - HOOD (-) INPUT 08 BLUE SILVER DOT 09 GRAY/BLACK SILVER DOT 0 EMPTY 0 EMPTY 0 EMPTY 03 BROWN/RED - CANH 04 BROWN/YELLOW - CANL 05 BLUE/RED 06 BLUE/YELLOW 07 EMPTY 08 ORANGE 09 YELLOW 0 EMPTY GRAY/RED GRAY/YELLOW 3 GREEN/RED 4 ORANGE/WHITE - AUTOLIGHT (-) OUTPUT 5 BROWN 6 ORANGE/BLACK 7 PINK 8 PURPLE 9 RED 0 BLACK 3A 3A CANH (DATA) YELLOW - 08 CANL (DATA) LTGREEN - 09 V (+) WHITE - 0 DRIVER DOOR PIN (-) YELLOW - 6 PARKING LIGHT (+) YELLOW - 0 PARKING LIGHT (+) BROWN - 3 ALARM SENSOR (DATA) PURPLE - 0 APPLY LY IF VEHICLE IS EQUIPPED WITH PROXIMITY SENSOR : BLACK/WHITE : BLACK 3 9 : BROWN : WHITE IMMOBILIZER, RIGHT SIDE STEERING COLUMN (B) ETACS/ECU, FUSEBOX LEFT SIDE DASH (C) 3 0 OVERHEAD CSOLE, NEAR RADAR SENSOR (D) 3 M5 0 GRAY/BLACK BLUE DOT - ALARM SENSOR (DATA) VEHICLE SIDE 0 WHITE/BLACK BLUE DOT 03 GRAY/RED BLUE DOT - ALARM SENSOR (DATA) CNECTOR SIDE 04 WHITE/RED BLUE DOT 05 GRAY BLUE DOT 06 WHITE BLUE DOT HORN (-) HOOD SWITCH 0C_v_[W] Automotive Data Solutions Inc. 06 INSTALL THE SUPPLIED HOOD SWITCH IF THE VEHICLE IS NOT EQUIPPED WITH E Mitsubishi Outlander STD key AT

101 MODULE PROGRAMMING PROCEDURE - OF PAGE 4 OF Insert key into ignition. 07 Press and release the module s programming button. 0 Turn key to position. 08 Release the brake pedal. 03 Wait, LED will turn solid GREEN for seconds. 09 Wait, LED will flash GREEN. 04 Turn key to position. 0 Module Programming Procedure completed. 05 vehicle for 5 seconds. 06 Press and hold the brake pedal. Automotive Data Solutions Inc Mitsubishi Outlander STD key AT

102 TAKEOVER PROCEDURE - STD KEY - OF PAGE 5 OF >> All vehicle doors must be closed and locked prior to remote start sequence. >> Failure to follow procedure will result in vehicle engine shutdown. 0 Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. 03 Turn key to position. 04 Press and release BRAKE pedal. 05 Take over procedure completed. Automotive Data Solutions Inc Mitsubishi Outlander STD key AT

103 INSTALLATI CHECKLIST - OF PAGE 6 OF CHECKLIST - WITH AFTERMARKET KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. 9 Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle. Close all vehicle doors, hood and trunk. Question 7: Does the vehicle shut down? 3 Press the LOCK button once [x] on the aftermarket keyfob. YES: Go to next step. Question : Do the doors lock? NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle YES: Go to next step. and call technical support. NO: Verify the remote programming, the RF connections and the wired door lock/unlock 0 RAP and auto light shutdown test connections as illustrated in the wiring diagram, if applicable. Repeat the test and call Question 8: Did the radio, interior controls and headlights turn off within 60 seconds after remote start shutdown? 4 Press the UNLOCK button once [x] on the aftermarket keyfob. Question : Do the doors unlock? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 5 Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Question 3: Does the trunk or hatch open/unlock? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call 6 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 4: Does the driver side sliding door open? YES: Press the AUX button once [x] to close the driver sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 7 Press the AUX button once [x] on the aftermarket keyfob if supported. Question 5: Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call 8 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 6: Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 3 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question 9: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 4 Close hood. 5 Enter vehicle and close the doors. 6 Press the /STOP button once [x] on the aftermarket keyfob to remote start vehicle. 7 Wait for the vehicle to start. 8 Press brake pedal. Question 0: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press the /STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 0 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Outlander STD key AT

104 INSTALLATI CHECKLIST - OF PAGE 7 OF CHECKLIST - WITH OEM KEYFOB WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. 3 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question : Does the vehicle remote start? YES: Go to next step. NO: The module doesn't detect OEM remote lock button from the vehicle communication network. Check all connections, repeat the test and call 4 Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down vehicle. Question : Does the vehicle shut down? YES: Go to next step. NO: Repeat step. If the problem persists, press on the brake pedal once [x] to shut down the vehicle and call technical support. 5 RAP Shutdown test Question 3: Did the radio, interior controls, and headlights turn off within 60 seconds after remote start shutdown? YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call 6 Open hood. 7 If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. 8 Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Question 4: Does the vehicle remote start? YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. 9 Close hood. 0 Enter vehicle and close the doors. Press LOCK button three times [3x] rapidly on the OEM keyfob to remote start vehicle. Wait for the vehicle to start. 3 Press brake pedal. Question 5: Does the vehicle shut down? YES: Go to next step. NO: The module does NOT detect the brake pedal signal. Press LOCK button three times [3x] rapidly on the OEM keyfob to shut down, check the brake connection as illustrated in the wiring diagram, if applicable, and call technical support. 4 Exit vehicle. 5 Installation checklist completed. Automotive Data Solutions Inc Mitsubishi Outlander STD key AT

105 INSTALL GUIDE Mitsubishi Outlander STD key AT DOCUMENT NUMBER REVISI DATE FIRMWARE ADS-HCX(RSA)-MI-[ADS-HCX] HARDWARE ADS-HCX ESSORIES ADS-USB (OPTIAL) ADS-WLM-AN/ADS-WLM-AP (OPTIAL) DRE MOBILE DR-000 (OPTIAL) COMPATIBLE RF-KIT (OPTIAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 06