INSTALLATION GUIDE. Electronic Bidet Seat. BEYOND TECHNOLOGY Powered by TOTO

Transcription

1 INSTLLTION GUIDE Electronic idet Seat EYOND TECHNOLOGY Powered by TOTO

2 Installation Guide efore installation, be sure to read this installation guide and the separate safety sheet. Mount parts properly according to the instructions. Precautions before installation Only turn on the electricity and water supply for the product after all other installation work has been completed. Do not damage the connection components on the water supply hose (C-3). The water supply pressure range is between 0.1MPa (dynamic) and 1.0MPa (static) in Europe. Use the unit within the specified pressure range. The water temperature must be within a range of 0 to 35 C. Make sure the temperature is within this range. The ambient temperature during operation must be within a range of 0 to 40 C. Make sure the temperature is within this range. s a water flow test is conducted on each product at the factory, a small amount of water may remain inside the product. This water does not indicate a problem with the product. ll-pole disconnection incorporated in the fixed wiring shall be provided. Symbols and their meanings This task must be carried out by the installer. This function is performed automatically by. Visual confirmation is required for this. Indicates the workflow direction. 2

3 Specifications Check the appropriate type for your mains connection in the table below, and then wire and install the product correctly. Rated power supply Rated power consumption Maximum power consumption Power cord length V alternating voltage, 50 Hz (fl uctuating) W (fl uctuating) 1528W (t a water supply temperature of 0 C) 0,62 m Prepare an outlet position in advance that conforms to the regulations in your country. 180 mm 355 mm 320 mm 255 mm 220 mm 190 mm 3

4 Included Parts -1-2 C C-4 C-2 C-3 nti-theft protection for the remote control Please ask the home owner if he would like to have the remote control anti-theft kit installed before starting installation. Please leave the anti-theft kit with the owner if it is not installed

5 Required tools/items Use a soft, damp cloth to prevent damage to the product Ø = 3 mm 2x Ø = 6 mm

6 Installation procedure 1 Switch the circuit breaker in the fuse box to OFF. 180 mm 355 mm 320 mm 255 mm 220 mm 190 mm -8 C D C cm -9 C D E Phase Neutral Earth 6

7

8 8-6 C-3 C-1 Press C-1 into -6 until C-1 engages with a click. (fter C-1 is mounted, make sure that it cannot be removed even if it is pulled.) 8

9 9 Switch the circuit breaker in the fuse box to ON. 9

10 Mounting the remote control C mm -1 Side wall 1060 mm 760 mm 250 mm 390 mm 250 mm -1 Rear wall 1060 mm 760 mm 10

11 12 Temporarily place the remote control in the position determined in 11 and check the signal reception at -1. Hold down -1-4 C C-4 13 C 11 11

12 13 Ø = 6 mm Ø = 3mm C -2-1 nchored by magnet. 12

13 nti-theft protection for the remote control Ø = 6mm Ø = 3mm -5-5 C D -1 E

14 Trial run 14 Open the water shutoff valve (-8) C Hold down Hold down C-4 14

15 Dimensions 390mm 134 mm 260mm 485mm 547mm 220mm 64mm 392mm 594mm mm Information for the installer Please explain the features and operation of to the customer. If the product will not be used for a long time (for example, when it is installed in an unoccupied, newly constructed building), switch the circuit breaker in the fuse box to OFF. For information on How to dismount the main unit, please refer to the separate sheet. 15

16 VILLEROY&OCH GERMNY Villeroy&och G athroom and Wellness Division Headquarter D Mettlach EN Colours and dimensions are subject to commonly accepted tolerances. Subject to technical changes and colour modifications.