PETK Power and End Termination Kit
|
|
- Leona Harrison
- 5 years ago
- Views:
Transcription
1 Power and End Termination Kit -1 for BSX, RSX, VSX - for KSX, HTSX - for HPT, FP --ECM for HPT, FP --ZT for HPT, FP Order separately to be used in conjunction with Thermon connection kits
2 Receiving, Storing and Handling Inspect materials for damage incurred during shipping.. Report damages to the carrier for settlement.. Identify parts against the packing list to ensure the proper type and quantity has been received.. Store in a dry location. Power and End Termination Kits (per cable) -1 for BSX, RSX, VSX - for KSX, HTSX - for HPT, FP --ECM for HPT, FP --ZT for HPT, FP Warnings... Due to the risk of electrical shock, arcing and fire caused by product damage or improper usage, installation or maintenance, a ground-fault protection device is required. Installation must comply with Thermon requirements (including form PN 7U for Ex systems) and be installed in accordance with the regulations as per the norm EN IEC 79-1 for hazardous areas (where applicable), or any other applicable national and local codes. Component approvals and performance ratings are based on the use of Thermon specified parts only. De-energize all power sources before opening enclosure. Keep ends of heating cable and kit components dry before and during installation. Kit Contents... 1 Minimum bending radius of heating cable is mm (except HPT is 7 mm and FP is 19 mm). Individuals installing these products are responsible for complying with all applicable safety and health guidelines. Proper Personal Protective Equipment (PPE) should be utilized during installation. Contact Thermon if you have any additional questions. Tools Required Item Qty. Description 1 1 RTV Tube 1 Power Connection Boot 1 End Cap 1 Tape Strip (- Only) 1 End Termination Caution Label Certifications/Approvals 1... FMG 1.X Ex eb IIC T-T, Ex tb IIIC T1 C-T8 C 17 II GD Ex eb IIC T-T, Ex tb IIIC T1 C-T8 C, FM 1ATEX8X 1 Grommet (For - Terminator kits only) 7 1 Ground Sleeve 8 Conductor Wire Pins 9 1 Braid Wire Pin Note: 1. These sets have been evaluated as components of Thermon s Approved connection kits, such that the area use ratings depend on the rating of the connection kits.
3 IMPORTANT! Heating cable must be properly installed within expediter assembly and mounted to pipe prior to terminating with kit. See Terminator Installation Instructions for expediter mounting details. GRW GRW-G GRW-GT GRW-G/Tstat Terminator: Route cable through base entry and mount expediter to pipe using pipe band. Do not band over cable. For HPT and FP cable exchange grommet supplied in Terminator kit with: GRW-G provided in - GRW-GT provided in --ECM GRW-G/Tstat provided in --ZT Step 1: Remove Heating Cable Overjacket and Separate Metallic Braid to Form Pigtail 1 mm ( ) 1a. Cut and remove heating cable overjacket. Do not cut metallic braid. 1b. Separate braid strands at edge of overjacket and pull cable through opening in braid. 1c. Twist braid into a pigtail. Trim ends of braid. Step : Matrix Removal for BSX, RSX, HTSX, KSX, and VSX Cables mm (.1 ) mm (.1 ) a. Cut and remove primary insulation jacket (BSX and RSX cables only). b. Cut a mm strip of conductive matrix between the conductors. Do not cut bus wire strands. c. Cut and remove the mm matrix strip.
4 Step : Heating Element Removal for HPT and FP Cables 1 mm (.7 ) 117 mm (. ) a. Cut and remove primary insulation jacket. NOTE: Bus connection must be no more than mm ( ) from pipe as addressed in connection kit instructions. b. Cut and remove fiberglass overlay and heating element. Push any remaining heating element wire under the primary insulation jacket. c. Cut and remove pairing jacket. Do not cut bus wire insulation. Step : Install Power Boot on Heating Cables 1 mm (. ) a. Apply a liberal amount of RTV sealant to cable. b. Slide boot onto the end of the cable and green/yellow ground sleeve over twisted braid. Expose 1mm (. ) of bus wire. c. Crimp conductor wire pins on each conductor. Crimp braid wire pin on twisted braid. Expose 1mm (. ) of bus wire.
5 Step : End Termination for BSX, RSX, HTSX, KSX, and VSX Cables 1 mm (. ) a. Cut and remove heating cable overjacket. b. Trim away exposed braid from cable. c. Apply a liberal amount of RTV sealant to cable and inside end cap. Slide end cap onto end of cable. Step : End Termination for HPT and FP 7 mm ( ) mm (1 ) 19 mm (.7 ) Bus Connection a. Trim the cable 7mm ( ) from the bus connection. b. Cut and remove overjacket and trim away exposed braid from cable. c. Cut and remove primary insulation jacket. mm (. ) d. Cut and remove fiberglass overlay and heating element. Push any remaining heating element wire under the primary insulation jacket. e. Cut and remove pairing jacket. Stagger cut one of the bus wires. Do not cut bus wire strands. f. Tape bus wires individually and then together. Continue taping to cover overjacket. Apply a liberal amount of RTV sealant to cable and slide end cap onto the end of the cable.
6 Cable Take-off for BSX, RSX, HTSX, KSX and VSX For Power Connecton Boot Termination For End Cap Termination
7 Cable Take-off for HPT and FP Heating Cables mm inches mm inches NOTE: Bus connection must be no more than mm ( ) from pipe as addressed in connection kit instructions. For Power Connection Boot Termination For End Cap Termination THERMON... The Heat Tracing Specialists European Headquarters Boezemweg PO Box AE Pijnacker The Netherlands Phone: +1 () Specifications and information subject to change without notice. Corporate Headquarters 1 Thermon Dr. PO Box 9 San Marcos, TX USA Phone: PN1U-11 For the Thermon office nearest you visit us at...
SCTK Splice Connection Termination Kit
Splice Connection Termination Kit SCTK- for BSX, RSX, VSX SCTK- for KSX, HTSX SCTK- for HPT, FP To be used in conjunction with Thermon Connection kits Receiving, Storing and Handling.... Inspect materials
More informationPETK Power and End Termination Kit
PETK Power and End Termination Kit INSTALLATION PROCEDURES Made in USA PETK-1 for BSX, RSX, VSX PETK- for KSX, HTSX PETK- for HPT, FP PETK--ECM for HPT, FP Order separately to be used in conjunction with
More informationPETK Power and End Termination Kit
Power and End Termination Kit PETK-1D PETK-2D PETK-D for BSX, RSX, VSX for KSX, HTSX for HPT, FP Order separately to be used in conjunction with Thermon connection kits Receiving, Storing and Handling...
More informationSCTK INSTALLATION PROCEDURES. Splice Connection Termination Kit. SCTK-1 for BSX, RSX, VSX SCTK-2 for KSX, HTSX SCTK-3 for HPT, FP
Splice Connection Termination Kit INSTALLATION PROCEDURES SCTK- for BSX, RSX, VSX SCTK- for KSX, HTSX SCTK- for HPT, FP To be used in conjunction with Thermon Connection kits Receiving, Storing and Handling....
More informationZP-XP Power Connection Kit. Terminator. The Heat Tracing Specialists INSTALLATION PROCEDURES
Terminator TM ZP-XP Power Connection Kit For Powe Connection, In-Line Splice Connection, T-Splice Connection or End Termination Applications The Heat Tracing Specialists The following installation procedures
More informationTerminator ZP/FAK-1 Kit Electrically Heated TubeTrace Bundles
Terminator ZP/ Kit Electrically Heated TubeTrace Bundles Listed Cable System 17M Terminator ZP/ The following installation procedures are suggested guidelines for the installation of the Terminator ZP/
More informationIn-Line / T-Splice Kit Installation Instructions. Terminator DS-L for use with RSX, TSX, VSX self-regulating heating cables
In-Line / T-Splice Kit Installation Instructions Terminator DS-L for use with RSX, TSX, VSX self-regulating heating cables Terminator DS-S for use with BSX *, HTSX, KSX self-regulating, HPT power-limiting,
More informationTerminator DL-S for use with BSX *, HTSX, KSX self-regulating, HPT power-limiting, and FP constant watt heating cables
Lighted Power Connection / Lighted End Termination Kit Installation Instructions Terminator DL-L for use with RSX, TSX, VSX self-regulating heating cables Terminator DL-S for use with BSX *, HTSX, KSX
More informationTerminator ZP/FAK-5 and 5L
for of Electrically Heated TubeTrace Bundles Listed Cable System 17M Ordinary & Hazardous Locations Class I, Division, Groups A, B, C & D Class II, Division, Groups F & G, Class III Class I, Zone 1, AEx
More informationTerminator. DP Power Connection Kit INSTALLATION PROCEDURES
Terminator TM DP Power Connection Kit For Power Connection, In-Line Splice Connection, T-Splice Connection, or End Termination Applications Receiving, Storing and Handling... 1. Inspect materials for damage
More informationTracePlus. VIL-6 End of Circuit Light Kit INSTALLATION PROCEDURES. VIL-6-H for BSX, HTSX, KSX, HPT, FP VIL-6-V for RSX, TSX, VSX
TracePlus TM For End Termination Applications VIL-6 End of Circuit Light Kit INSTALLATION PROCEDURES VIL-6-H for BSX, HTSX, KSX, HPT, FP VIL-6-V for RSX, TSX, VSX TracePlus VIL-6 The following installation
More informationTerminator ZP/FAK-4L Kit Electrically Heated TubeTrace Bundles
Terminator ZP/ Kit Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES Listed Cable System 137M Terminator ZP/ The following installation procedures are suggested guidelines for the installation
More informationTracePlus. PCA Power Connection Kit INSTALLATION PROCEDURES. PCA-H for BSX, HTSX, KSX, HPT, FP PCA-V for RSX, TSX, VSX
TracePlus TM PCA Power Connection Kit INSTALLATION PROCEDURES PCA-H for BSX, HTSX, KSX, HPT, FP PCA-V for RSX, TSX, VSX For Power Connection, In-Line Splice Connection, T-Splice Connection, or End Termination
More informationTerminator TM DL Lighted Power Connection/End Termination Kit INSTALLATION PROCEDURES. For Power Connection or End Termination Applications
Terminator TM DL Lighted Power Connection/End Termination Kit INSTALLATION PROCEDURES For Power Connection or End Termination Applications Terminator DL The following installation procedures are suggested
More informationTerminator DP/FAK-4 and FAK-4L for In-Line Splice of Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES
for In-Line Splice of Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES The following installation procedures are suggested guidelines for the installation of the Terminator DP/FAK-4 and FAK-4L
More informationTerminator DP/FAK-4LHT Kit for In-Line Splice of Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES
Terminator DP/HT Kit for In-Line Splice of Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES Terminator DP/HT The following installation procedures are suggested guidelines for the installation
More informationTerminator DP/FAK-5 and FAK-5L
for T-Splice of Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES The following installation procedures are suggested guidelines for the installation of the Terminator DP/FAK-5 and FAK-5L:
More informationTerminator DP/FAK-2 and FAK-2L. Elbow Splice Kit for Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES
Elbow Splice Kit for Electrically Heated TubeTrace Bundles The following installation procedures are suggested guidelines for the installation of the Kit. Receiving, Storing and Handling 1. Inspect materials
More informationTerminator DP/FAK-5LHT Kit for Tee Splice of Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES
Terminator DP/FAK-5LHT Kit for Tee Splice of Electrically Heated TubeTrace Bundles INSTALLATION PROCEDURES Terminator DP/FAK-5LHT The following installation procedures are suggested guidelines for the
More informationPower Connection Kit Installation Instructions. Terminator ZP-M for use with TEK and HTEK series constant watt heating cables
Power Connection Kit Installation Instructions Terminator ZP-M for use with TEK and HTEK series constant watt heating cables For Power Connection (1 Cable), In-Line Splice Connection, or End Termination
More informationPower Connection Kit Installation Instructions. Terminator DP-M for use with TEK and HTEK series constant watt heating cables
Power Connection Kit Installation Instructions Terminator DP-M for use with TEK and HTEK series constant watt heating cables For Power Connection (1 Cable), In-Line Splice Connection, or End Termination
More informationFAK-7HTS High Temperature Tubing Bundle End Seal Kit INSTALLATION PROCEDURES
High Temperature End Seal Kit The following procedures are guidelines for the installation of the FAK-7HTS High Temp. End Seal Kit. Receiving, Storing and Handling... 1. Inspect materials for damage incurred
More informationElectric Heat Tracing INSTALLATION PROCEDURES
INSTALLATION PROCEDURES Complete Electric Heat Tracing System... Types of Heating Cables 1... Self-Regulating Heating Cables: BSX (refer to Form TEP0067U) 1725 II 2 G & D Ex e II T5 or T6 DEMKO 02ATEX0132424,
More informationElectric Heat Tracing INSTALLATION PROCEDURES
Electric Heat Tracing INSTALLATION PROCEDURES Electric Heat Tracing Complete Electric Heat Tracing System... Illustration A: Typical Heat Tracing Installation A complete electric heat tracing system will
More informationRT FlexiPanel TM Tank and Vessel Heating Panel
RT FlexiPanel TM Tank and Vessel ing Panel Application... Metallic Tank and Vessel ing The RT FlexiPanel is a self-contained, high performance flexible heating panel designed specifically for use on metallic
More informationDEVI EasyConnect Heating Cable Connection System
Installation Instructions DEVI EasyConnect Heating Cable Connection System IP 68 0 mm 10 20 30 40 50 60 70 80 90 100 110 120 Standards: DIN VDE 0606 T200, DIN EN 61984 (VDE 0627), VDE 0110 IEC 60999; CSA:
More informationUPC Power Connection Kit
Installation Instructions UPC Power Connection Kit For Self-Regulating & Constant Wattage Heating Cables PJ495-5 161-562581-029 January 2017 2 UPC Power Connection Kit Self-Regulating & Constant Wattage
More informationC Power Connection Kit
1548-4000C Power Connection Kit For use with Dekoron 2700 Family of Heating Cables Installation Instructions Kit Description The Dekoron 1548-4000C electrical connection kit distirbuted by Heat-Line is
More informationET-PWR-END-KIT Installation Instructions (part #JSR00)
(part #JSR00) Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and others by observing all safety
More informationJBM-100-STB NEMA 4X-rated connection kit Installation Instructions
JBM-100-STB NEMA 4X-rated connection kit Installation Instructions Power Connection, Powered Splice, Powered Tee, Dual Power Connection, Splice or Tee with Junction Box Approvals Hazardous Locations CLI,
More informationJBS-100-STB Single Entry Power Connection with Junction Box Installation Instructions
JBS-100-STB Single Entry Power Connection with Junction Box Installation Instructions Description The JBS-100-STB is a NEMA 4X rated power connection kit. It is designed for use with Raychem BTV-CR, BTV-CT,
More informationTubeTrace Tubing Bundles
for Custom CEMS and Analytical Umbilicals English Units Receiving, Storing and Handling... 1. Inspect materials for damage incurred during shipping. Report damages to carrier for settlement. 2. Identify
More informationProducts and Accessories. Information Guide
Products and Accessories Products And Accessories SELF-REGULATING HEATING CABLES Features: Semiconductive Self-Regulating Heating Matrix Cut-to-Length Parallel Circuitry Nickel-Plated Copper Bus Wires
More informationFLX TM Self-Regulating Winterization/Freeze Protection INSTALLATION PROCEDURES
FLX TM Self-Regulating Winterization/Freeze Protection INSTALLATION PROCEDURES FLX TM Self-Regulating Refer to the FLX Cable Testing Report for required recording of test data and circuit information.
More informationJBS-100-A, A6 SINGLE ENTRY POWER CONNECTION WITH JUNCTION BOX INSTALLATION INSTRUCTIONS
JBS-100-A, A6 SINGLE ENTRY POWER CONNECTION WITH JUNCTION BOX INSTALLATION INSTRUCTIONS DESCRIPTION The JBS-100-A and JBS-100-A6 are NEMA 4X-rated power connection kit. It is designed for use with Raychem
More informationHTSB system System overview
HTSB system System overview Easy planning of heating circuits Simple installation on site Wide operating temperature range The BARTEC HTSB heating system covers a wide range of applications in trace heating.
More informationABG Cable Glands Installation Procedure
ABG Cable Glands Installation Procedure ABG Cable Gland Range Baseefa 16ATEX0004X IECEx BAS 16.0011X Installation, Operation and Maintenance Instructions Material: Brass/ Brass with Nickel plated and Stainless
More informationSPC-P Smart Power Connection with Temperature Monitoring Transmitter Pipe Mounted Installation Instructions
SPC-P Smart Power Connection with Temperature Monitoring Transmitter Pipe Mounted Installation Instructions SPC-P with Pyrotenax MI heating cable using required MI cable grounding kit SPC-P with Raychem
More informationC A Heating Cable Gland Kit Installation Instructions
C75-100-A Heating Cable Gland Kit Installation Instructions Description The C75-100-A is a NEMA 4X-rated gland kit used to transition heating cables into a junction box when making connections off of a
More informationC A HEATING CABLE GLAND KIT INSTALLATION INSTRUCTIONS
C75-100-A HEATING CABLE GLAND KIT INSTALLATION INSTRUCTIONS DESCRIPTION The C75-100-A is a NEMA 4X-rated gland kit used to transition heating cables into a junction box when making connections off of a
More informationTSRT TSRT Tee Splice Kit Installation Instructions
TSRT TSRT Tee Splice Kit Installation Instructions Description The TSRS Splice Connection Kit is for use with all versions of EasyHeat s self regulating heater cables smaller than 0.44 (11mm) in diameter.
More informationInstallation & Operation Instructions. Type USL Signal Light Kit for Self-Regulating Constant Wattage Heating Cables. Constant Wattage Grommet
Chromalox Installation & Operation Instructions DIVISION 4 SALES REFERENCE DATE SERVICE REFERENCE SECTION RT (Supersedes PF477-1) PJ937 161-562581-032 DECEMBER, 2007 Type USL Kit for Self-Regulating Constant
More informationDEF-Trac. Design and Installation Guide. August 2014
DEF-Trac Design and Installation Guide August 204 A DEF-Trac Featuring a Flexible Corrugated Stainless Steel Core 2 TABLE OF CONTENTS USER WARNINGS... 4 DESIGN SPECIFICATIONS... 4 INSPECTION / HANDLING
More informationDEF-Trac. Design and Installation Guide. August 2015
DEF-Trac Design and Installation Guide August 205 DEF-Trac Featuring a Flexible Corrugated Stainless Steel Core 2 TABLE OF CONTENTS Section Page No..0 User Warnings... 4. DEF-Trac Flexible Piping System...
More informationSRK02 Hard Wire Power Connection Kit. Installation, Operation and Maintenance Instructions
SRK02 Hard Wire Power Connection Kit Installation, Operation and Maintenance Instructions IMPORTANT: Save These Instructions! Item Qty Description A 1 Black heat shrink tube (1/2 dia. x 1 length) B 2 Black
More informationHTP PTP/ PTJ Power Connection Kit for Pipes
HTP 1548-40PTP/1548-40PTJ Power Connection Kit for Pipes For use with Dekoron 2700 and 2300 Families of Heating Cables. 1548-81HTJ/81HTP for use with 2000 Series Heating Cables. Installation Instructions
More informationPRODUCTS&ACCESSORIES INFORMATION GUIDE SELF-REGULATING HEATING CABLES HTSXTM BSXTM VSXTM RSXTM KSRTM KSXTM
PRODUCTS&ACCESSORIES INFORMATION GUIDE SELF-REGULATING HEATING CABLES Features: Semiconductive Self-Regulating Heating Matrix Cut-to-Length Parallel Circuitry Nickel-Plated Copper Bus Wires Metallic Braids
More informationPower Connection Kit installation instructions
Operating instructions & Parts Manual ET00 Please read and save these instructions. Read carefully before attempting to assemble, install, operate or maintain the product described. Protect yourself and
More informationPMKG-JS POLYMATRIX SPLICE CONNECTION KIT INSTALLATION INSTRUCTIONS
PMKG-JS POLYMATRIX SPLICE CONNECTION KIT INSTALLATION INSTRUCTIONS DESCRIPTION The PolyMatrix PMKG-JS is a NEMA 4X rated splice connection kit for use with Raychem BTV-CR, BTV-CT, QTVR-CT, XTV-CT, KTV-CT
More informationPMKG-J2LP PolyMatrix Powered Splice Kit Installation Instructions
PMKG-J2LP PolyMatrix Powered Splice Kit Installation Instructions Description The PolyMatrix PMKG-J2LP is a NEMA 4X rated connection kit for use with Raychem BTV-CR, BTV-CT, QTVR-CT, XTV-CT, KTV-CT and
More informationEMK-XP ElectroMelt Power Connection and End Seal Kit Installation Instructions
EMK-XP ElectroMelt Power Connection and End Seal Kit Installation Instructions Description The ElectroMelt EMK-XP Power Connection and End Seal Kit is for use with ElectroMelt EM2-XR and EM3-XR heating
More informationUES-LL End Termination Kit
Installation Instructions UES-LL End Termination Kit for Series Long Line Heating Cables 1 PJ950 161-562681-022 July 2015 UES-LL End Termination Kit Kit Contents Item Qty Description Item Qty Description
More informationAutoMatrix Power Connection Kit. (1) This type 4X enclosure is intended for indoor or outdoor use primarily to. (2) May be required (see step 1).
R AMG-BC-III AutoMatrix Power Connection Kit Description The AMG-BC-III is a copper free aluminum (maximum 4/10 of 1% copper) NEMA 4X (1) rated power connection kit for single or dual heating cable entry.
More information3M Cold Shrink Silicone Rubber Outdoor Termination Kit QT-III 7600-S-3W Series
3M Cold Shrink Silicone Rubber Outdoor Termination Kit QT-III 7600-S-3W Series For 3-Conductor Copper Tape Shield Cables without Ground Wires Instructions IEEE Std. No. 48 Class 1 Termination CAUTION Working
More informationSteam Tracing DESIGN GUIDE
DESIGN GUIDE DESIGN GUIDE Contents Introduction... 2 Application Information... 2 Steam Tracing Design Outline... 3 Basis for a Good Design Step 1: Establish Design Parameters... 3 Step 2: Select Steam
More information3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination
3M Cold Shrink Silicone Rubber Termination QT-III 7600-S-3G Series Three-Core Outdoor Termination Instructions IEEE Std. No. 48 Class 1 Termination CAUTION Working around energized electrical systems may
More informationCold Shrink - Silicone Rubber QTII(X)4S-32H Series Cable Termination Instructions
Cold Shrink - Silicone Rubber QTII(X)4S-32H Series Cable Termination Instructions Class I Indoor Termination Voltage Designation: 12/20(24) kv Kit Contents: 1 HeatShrinkBreakoutBootAssembly 3 HeatShrinkBindingSleeves
More informationSegurança. Segurança. PSB Heating System Cold applied connection technology. Compulsório. Compulsório. Operation Manual and Installation Instructions
Segurança TC RU C-DE.ГБ06.B.00230 OCP 0004 Compulsório INMETRO Operation Manual and Installation Instructions Segurança PSB Heating System Cold applied connection technology Compulsório Type 27-1680-...0/...
More informationSpecification for Heated Instrument Tubing in Process Applications* (March 29, 2007)
Specification for Heated Instrument Tubing in Process Applications* (March 29, 2007) 1.0 SCOPE This specification outlines the minimum requirements for electrically traced or steam/fluid traced instrument
More information3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits
3M Cold Shrink QT-III Silicone Rubber Three-Core Termination Kits With High-K Stress Relief For 3-Conductor Type G (Ground Wire), Copper Tape Shield, Armored Cables 7600-S-3G Series Instructions IEEE Std.
More informationWarmTrace TM HSX Hot Water Temperature Maintenance INSTALLATION PROCEDURES
WarmTrace TM HSX Hot Water Temperature Maintenance INSTALLATION PROCEDURES WarmTrace TM HSX Safety Comes First... The safety and performance of a heat tracing system depends on how the system was designed,
More informationPRO-Tect Pipe Freeze Protection Self-Regulating Heating Cable Install Manual (PT-Series)
PRO-Tect Pipe Freeze Protection Self-Regulating Heating Cable Install Manual () Free Design Service 24/7 Installation Support (800) 875-5285 www.warmlyyours.com Assembly Tools Needed Utility knife Wire
More informationInstallation Instructions
K-Series Constant-Wattage Heating Cable Installation Instructions Read and understand this material before installing this heater. Failure to understand how to safely install the heater could result in
More informationPOWERHEAT TYPE AHT TERMINATION INSTRUCTIONS. Ref TK/AHT Issue C Date 16 August 1999
STOCKPORT, ENGLAND, TEL: 0161-430 8333 POWERHEAT TYPE AHT TERMINATION INSTRUCTIONS PLEASE READ THE INSTRUCTIONS BEFORE PROCEEDING Recommended Tools ANNEX B Ref TK/AHT Issue C Date 16 August 1999 Heavy
More informationInstallation Instructions (Translation) Marking. Description. Danger, warning and note symbols. Technical data. ANTARES ExtSet.
Description Marking The ANTARES ExtSet makes it possible to distribute the Remote I/O ANTARES modules of an explosion-protected Remote I/O system ANTARES among a maximum of 4 metal mounting rails. For
More information3M Cold Shrink QT-III Silicone Rubber 3/C Cabinet Mount Termination Kit
3M Cold Shrink QT-III Silicone Rubber 3/C Cabinet Mount Termination Kit With High-K Stress Relief For 3-Conductor Copper Tape Shield Cables with or without Ground Wires 7600-T-3RJS Series Instructions
More informationSegurança. Segurança. MSB/HSB Heating System. Compulsório. Compulsório. Operation Manual/Installation Instructions. Cold applied connection technology
Segurança TC RU C-DE.ГБ06.B.00230 OCP 0004 Compulsório INMETRO Operation Manual/Installation Instructions Segurança MSB/HSB Heating System Cold applied connection technology Compulsório Type 27-1.80-...0/...
More informationApplication Specification Circular Plastic Connector (CPC) Series 45 System 05 AUG 14 Rev D
Application Specification Circular Plastic Connector (CPC) 114-13137 Series 45 System 05 AUG 14 Rev D NOTE i All numerical values are in metric units [with U.S. customary units in brackets]. Dimensions
More informationSERGE BARIL HA-S HAZARDOUS AREA SEAL KIT
INSTRUCTIONS DESCRIPTION The HA-S Hazardous Area Seal Kit provides the cable termination and explosion proof seal parts needed to make all in-line electrical splice connections associated with Serge Baril
More informationProduct Overview. Application
Self-Regulating SC, SC/H Series-resistance heating cables for longline systems Electrical freeze protection for long pipelines in both nonhazardous and hazardous locations Power-Limiting Mineral Insulated
More informationEcoflex potable PEX plus pre-insulated pipe system Installation guide
Ecoflex potable PEX plus pre-insulated pipe system Installation guide Ecoflex potable PEX plus pre-insulated pipe system installation guide l 1 Uponor Ecoflex potable PEX plus pre-insulated pipe system
More informationQT-III Cold Shrink Silicone Rubber
QT-III Cold Shrink Silicone Rubber 7600-T-3RJS Series 3/C Cabinet Termination Instructions Kit Contents: 3ÑSilicone Rubber Phase Re-jacketing Sleeve Assembly 3ÑCold Shrink Silicone Rubber Termination Assembly
More informationSegurança. Segurança. PSB Heating System Heat shrink technology. Compulsório. Compulsório. Operation Manual/Installation Instructions
Segurança TC RU C-DE.ГБ06.B.00230 OCP 0004 Compulsório INMETRO Operation Manual/Installation Instructions Segurança PSB Heating System Heat shrink technology Compulsório Type 27-1680-...0/... OCP 0004
More informationSelf-Regulating Freeze Protection Heating Cable
D PDS SRF Self-Regulating Freeze Protection Heating Cable E C B A Output Self-Regulating, Energy Efficient Cost Effective for Contractor/Construction Freeze Protection Application Freeze Protection of
More informationUnarmored Variable Frequency Drive (VFD) Cable Termination Guide
Unarmored Variable Frequency Drive (VFD) Cable Termination Guide Be Certain with Belden A Step-by-Step Look at the Connection/Termination of Unarmored VFD Cables Terminating Unarmored Variable Frequency
More informationINSTALL INSTRUCTIONS DC C-EV. Installation Instructions: DC C-EV.
INSTALL INSTRUCTIONS DC6-48-60-0-8C-EV Installation Instructions: DC6-48-60-0-8C-EV INSTALL INSTRUCTIONS DC6-48-60-0-8C-EV Contents Section Description Page 1 Copyright 2 1.1 Disclaimer 2 1.2 Warnings
More informationE.S.P. Embedded Sensing Probes for Motor Brushes
E.S.P. Embedded Sensing Probes for Motor Brushes 2/13 Installation & Operating Manual MN609 Any trademarks used in this manual are the property of their respective owners. Important: Be sure to check www.baldor.com
More informationH900 WinterGard Power Connection Kit with End Seal Installation Instructions
H900 WinterGard Power Connection Kit with End Seal Installation Instructions Power connection for H311, H611, and H621 Power connection for H612 and H622 Description The WinterGard power connection kit
More informationLPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions
LPC Series Fiber Panel 12/24 Fiber Rack-Mount Enclosure Installation Instructions ADCP-92-129 Issue 1 6/2010 Content Page INTRODUCTION.............................................................................
More informationOPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS RTECK terminal boxes RTKB series IEC Ex EX010 TECHNICAL FILES CONTENTS: 1) Contents 2) General information 3) Safety information 4) Conformity to standards 5) Function 6) Technical
More informationMotor Lead Pigtail or V-Stub Splice 5380 Series For 5/8 kv Non-Shielded and Shielded Feeder Cables (Tape, Wire or UniShield Cables)
Motor Lead Pigtail or V-Stub Splice 5380 Series For 5/8 kv Non-Shielded and Shielded Feeder Cables (Tape, Wire or UniShield Cables) Instructions Kit Contents 3 Lug Covers 3 Cold Shrink Terminations 12
More informationBackside License Plate Mount for Jeep JK Wrangler
REQUIRED TOOLS 10mm SOCKET 13mm SOCKET 4mm HEX KEY WIRE CRIMPS WIRE STRIPPERS ELECTICAL TAPE SCREW DRIVER KIT CONTAINS BACKSIDE MOUNT LICENSE PLATE BRACKET WITH LEDS PLASTIC PASS-THROUGH GROMMET STAINLESS
More informationOperating Instructions
Important Information: These instructions contain safety information, read and follow them carefully. Dialight will not accept any responsibility for injury, damage or loss which may occur due to incorrect
More informationUSER MANUAL FOR THE BULKHEAD LIGHT FITTING, TYPE /..
d.o.o. tel. 049 222 900, fax 049 426 450 e-mail: tepex@tepex.hr www.tepex.hr USER MANUAL FOR THE BULKHEAD LIGHT FITTING, TYPE 0403.24/.. No: TEPEx.RS.077 Rev : 0 Date: 02.2016. CONTENT 1. Manufacturer
More informationTIDALFLUX 2300 F Quick Start
Quick Start Electromagnetic flow sensor for partially filled pipes The documentation is only complete when used in combination with the relevant documentation for the signal converter. KROHNE CONTENTS
More information3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TOW/WOT (RW)
3M Cold Shrink Silicone Rubber Skirted Termination Kit QT-III 7672-S-8-TOW/WOT (RW) for Tape Over Wire and Wire Over Tape Shielded Cable Instructions Class 1 Termination IEC 60840 72,5 kv 69 kv Class 325
More informationSLiC Aerial Terminal and Spiral End Seal for use with AMP* Quiet Front Terminal Blocks
SLiC Aerial Terminal and Spiral End Seal for use with AMP* Quiet Front Terminal Blocks Instructions June 2002 78-8130-2161-1-B 1 Contents: 1.0 General... 3 2.0 Kit Contents... 3 3.0 Cable Preparation...
More informationUNSIGNED HARDCOPY NOT CONTROLLED
Subject: APPROVED BY STATUS PURPOSE AFFECTED FUNCTIONS Flat Braid Cables Manager, Hardware Engineering Maintenance Revision Establishes the requirements for the fabrication of special-purpose electrical
More informationTermination Procedure for Subminiature SolderTacts Contacts for Coaxial Cable: D & D D & D
Print 12-Jun-03 1 of 11 Termination Procedure for Subminiature SolderTacts Contacts for Coaxial Cable: D-602-0218 & D-602-0219 D-602-0278 & D-602-0279 1. Scope This standard contains the termination procedures,
More informationNAMSR SELF-REGULATING FREEZE PROTECTION HEATING CABLE SELECTION
Self-Regulating, Energy Efficient Cost Effective for Contractor/Construction Freeze Protection Application Industrial Grade, 16 AWG Buss Wire Standard Braid with Overjacket Circuit Lengths to 460 Feet
More informationWarmlyYours ET-SR Series Heating Cable Installation Manual for Roof & Gutter Deicing
WarmlyYours ET-SR Series Heating Cable Installation Manual for Roof & Gutter Deicing Free Design Service 24/7 Installation Support (800) 875-5285 www.warmlyyours.com Assembly Tools Needed Utility knife
More informationWiring Assembly Instructions Section 5 P/N CASS P/N 1899AS RG316 P/N CASS P/N 1899AS RG316
Ver. 2.7 CASS USER S MANUAL VPC Tools Required For the assembly of the Mini-Coaxial Contact(s) VPC P/N 610 103 115/CASS P/N 1899AS284-01 and/or P/N 610 103 159/1899AS284-04 the following parts are required
More informationAssembly Instruction. EL OCHITO BLUE CONTACTS SuperSpeed USB TYPE I: PIN /SKT CABLE:
AI85114-02 Assembly Instruction EL OCHITO BLUE CONTACTS SuperSpeed USB TYPE I: PIN 858-028-01/SKT 858-029-01 CABLE: 963-118 Revision History Rev Date Initiated By Approved 1 07/16/18 WLL GH 1.0 Tools Tools
More informationTechnical Data. Dimensions
Model Number Features 40 mm flush 4-wire DC ATEX-approval for zone 2 and zone 22 S Technical Data specifications Switching element function PNP NO/NC Rated operating distance s n 40 mm Installation flush
More informationAssembly Instruction EL OCHITO WHITE CONTACTS 1000BASE-T/10GBASE-T TYPE I: PIN /SKT CABLE: S/FTP
AI85112-02 Assembly Instruction EL OCHITO WHITE CONTACTS 1000BASE-T/10GBASE-T TYPE I: PIN 858-003-02/SKT 858-032-02 CABLE: 963-033-26 S/FTP Revision History Rev Date Initiated By Approved 1 07/05/18 WLL
More informationThe following table shows the symbols used on the product and/or in this manual. Hazardous Voltage. Risk of electric shock.
i6000s Flex AC Current Probe Instruction Sheet Introduction The i6000s 24 Flex and i6000s 36 Flex AC Current Probes (hereafter referred to as the Probes ) are used with oscilloscopes, digital multimeters,
More informationSECTION 1: Field Inspection Guide for Rooftop Photovoltaic (PV) Systems
COUNTY OF SANTA CRUZ PLANNING DEPARTMENT 701 OCEAN STREET, 4 th FLOOR, SANTA CRUZ, CA 95060 (831) 454-2580 FAX: (831) 454-2131 TDD: (831) 454-2123 KATHLEEN MOLLOY PREVISICH, PLANNING DIRECTOR Photovoltaic
More informationGuaRdboX - Gd series IOM (Installation, Operation & Maintenance Manual) 0100-ENG rev.4
1. Introduction: This instruction manual contains important information regarding the safety instructions, installation, operation, maintenance and storage of the Guardbox limit switch boxes. The limit
More informationi3000s/i2000 Flex AC Current Probe
i3000s/ AC Current Probe Instruction Sheet Introduction The i3000s 24 Flex, i3000s 36 Flex, and AC Current Probes (the Probe) are used with oscilloscopes, digital multimeters, recorders or data loggers.
More informationHeating Cable. Description
Single Entry Power Connection Kit NEMA 4X Entry for 1 Cable 3/4 Conduit Hub Opening Lighted or Non-Lighted Multiple Entry Connection Box NEMA 4X Entry for up to 3 Cables Power, Splice or Tee Connection
More information