Series C1 Electronic Metering Pump. Specification Sheet and Assembly Details Manual No : 1619, 1829 Rev. : G, D Rev. Date : 6/09, 10/2015

Transcription

1 INJECTION CHECK VALVE COUPLING NUT DISCHARGE TUBING 4 FUNCTION VALVE PUMP HEAD SPACER, E.P.U. METERING PUMP HOUSING RETURN LINE (PRESSURE RELIEF) SPEED KNOB STROKE KNOB SUCTION FITTING SUCTION TUBING WEIGHT POWER CORD FOOT VALVE Metering Pump Component Diagram Series C1 Electronic Metering Pump Specification Sheet and Assembly Details Manual No : 1619, 1829 Rev. : G, D Rev. Date : 6/09, 10/2015 sales@novatech-usa.com Tel: (866) Fax: (866) Tel: (281) Fax: (281)

2 Specification Sheet Series C GENERAL Chemical metering pumps shall be positive displacement, Liquifram type pumps that are UL and CUL approved. Output volume shall be adjustable while pumps are in operation from zero to maximum capacity of: C10, C70, C GPH C11, C71, C GPH C12, C72, C GPH C13, C73, C GPH C14, C74, C GPH C76* GPH C77* GPH C78* GPH (4.9 liters per hour) (9.5 liters per hour) (15.1 liters per hour) (30.0 liters per hour) (75.7 liters per hour) (15.1 liters per hour) (38.0 liters per hour) (95.0 liters per hour) Chemical metering pumps shall be capable, without a hydraulically backed diaphragm, of injecting solutions against pressures up to: C10, C70, C90 C11, C71, C91 C12, C72, C92 C13, C73, C93 C14, C74, C94 C76* C77* C78* psig 150 psig 100 psig 60 psig 25 psig 175 psig 80 psig 30 psig (20.7 bar) (10.3 bar) (6.9 bar) (4.1 bar) (1.7 bar) (12.1 bar) (5.5 bar) (2.1 bar) TYPE C1 Adjustment shall be by means of readily accessible dial knobs, one for changing stroke length and the other for changing stroke frequency (speed). Both knobs are to be located opposite the liquid handling end. TYPE C7 Control of Series C7 metering pumps shall be selectable between internal and external pulsing by means of a 3-position center-off switch. Stroke length shall be adjustable by means of readily accessible dial knob. When in external pulsed mode, Series C7 units shall accept signals without the use of electrical timer or internal timer. Pressure capacity shall be adjustable to reduce noise, vibration and wear. tactile keypad. Internal stroke frequency shall be adjustable from 1 stroke per hour to 100 strokes per minute. Pressure capacity shall be keypad adjustable to reduce noise, vibration and wear. Metering pump shall be capable of dividing or multiplying pulse inputs from 1 to 999 or responding directly or inversely to a 4-20mA input signal. DRIVE The pump drive shall be totally enclosed with no exposed moving parts. Solid state electronic pulser shall be encapsulated and supplied with quick connect terminals at least 3/16" (4.75 mm) wide. Electronics shall be housed in chemical resistant enclosure at the rear of the pump for maximum protection against chemical spillage. Electrical power consumption shall not exceed 87 watts under full speed and maximum pressure conditions. Pump weight shall not exceed 28 lbs (12.7 kg). AUTOMATIC PRESSURE RELIEF To eliminate need for pressure relief valve, LiquiframTM shall automatically stop pulsating when discharge pressure exceeds pump pressure rating by not more than 35%. MATERIAL Chemical metering pump housing shall be of chemically resistant glass fiber reinforced thermoplastic with a glass fiber reinforced polypropylene EPU carrier1. All exposed fasteners shall be stainless steel. Chemical metering pump valves shall be ball type, with ceramic balls2. Valve seat and seal ring shall be renewable by replacing the combination seat-seal ring3 or cartridge valve assembly. Pump head shall be of transparent acrylic4 material capable of resisting the pumped chemical. Fittings and connections at pump head shall be PVC5. CHECK VALVES AND TUBING TYPE C9 A total of 16 ft (4.8 m) of polyethylene tubing6 shall be provided per pump complete with compression connections. A foot valve with integral one piece strainer shall be provided for the suction line, and an injection check/back pressure valve with ½" NPT male connection for the injection point. The injection check valve shall incorporate a dilating orifice which prohibits scale formation and accumulation of crystalline deposits. Series C9 metering pumps shall have a clear liquid crystal display. Control shall be selectable between internal and external pulsing by means of a (* - Not UL or CUL Approved) Notes: 1. With plastic coated cast iron EPU carrier for Series C 76, C77 and C Type 316 stainless steel or PTFE may be specified. 3. Hypalon, PTFE, Viton or Polyprel may be specified. 4. PVC, Polypropylene, PDVF or Type 316 stainless steel may be specified. 5. PVDF, Polypropylene, or Type 316 stainless steel may be specified ft. (1.8 m) of vinyl suction tubing may be specified in place of polyethylene for the suction side only. 1/4" or 1/2" male pipe thread may be specified. 201 Ivyland Road Ivyland, PA USA TOLL FREE: (800) TEL: (215) FAX: (215) Replaces same of Rev. F 11/ G 6/09

3 *10.8 (274mm) Maximum 7.5 (190mm) 5.70 (145mm) *13.9 (353mm) Maximum 5.16 (131mm) *Dimensions shown are maximum for largest liquid end available.these dimensions vary depending on the liquid end selected. Radius R2.7mm 4.50 (114mm) *6.3 (160mm) Maximum 4.70 (119mm) 2009 Milton Roy Company - All Rights Reserved Printed in USA Specifications subject to change without notice. Polyprel is a registered trademark of Milton Roy Company. Liquifram is a trademark of Milton Roy Company. Hypalon and Viton are registered trademarks of E. I. du Pont de Nemours & Co., Inc.

4 SERIES C1 DRIVE ASSEMBLY EXPLODED VIEW DIAGRAM Included In C1X2 ONLY

5 SERIES C1 DRIVE ASSEMBLY PARTS LIST Key 1 2 Model Series Part Description C101, C Control Panel Assembly, 115V 1 C102, C Control Panel Assembly, 230V US 1 C103, C105, C106, C107, C113, C115, C116, C Control Panel Assembly, V 1 C Control Panel Assembly, 115V 1 C Control Panel Assembly, 230V US 1 C123, C125, C126, C Control Panel Assembly V 1 C Control Panel Assembly, 115V 1 C Control Panel Assembly, 230V US 1 C133, C135, C136, C Control Panel Assembly, V 1 C Control Panel Assembly, 115V 1 C Control Panel Assembly, 230V US 1 C143, C145, C146, C Control Panel Assembly, V 1 C101, C111, C121, C131, C Housing Assembly, 115V 1 C102, C112, C122, C132, C Housing Assembly, 230V US 1 C103, C113, C123, C133, C Housing Assembly, 230V DIN 1 C105, C115, C125, C135, C Housing Assembly, 240V UK 1 C106, C116, C126, C136, C Housing Assembly, 250V AUST 1 C107, C117, C127, C137, C Housing Assembly, 230V SWISS 1 C EPU & Spacer w/stroke Adj., 115V, 0.9SI 1 C102, C103,C105, C106,C EPU & Spacer w/stroke Adj., 230V, 0.9SI 1 C111,C EPU & Spacer w/stroke Adj., 115V, 1.8SI 1 3 C112, C113,C115, C116,C117, C122,C123,C125, C126, C EPU & Spacer w/stroke Adj., 230V, 1.8SI 1 C131,C EPU & Spacer w/stroke Adj., 115V, 3.0SI 1 C132, C133, C135, C136, C137, C142, C143, C145, C146, C EPU & Spacer w/stroke Adj., 230V, 3.0SI 1 4 C Stroke Bracket Assembly 1 5 C Speed Knob 1 6 C Gasket 1 7 C Panel with Nameplate 1 8 C O-Ring 1 9 C Grommet 1 10 C O-Ring 1 11 C Speed Shaft 1 12 C Dual Pin 1 13 C Stroke Knob Assembly 1 Qty

6 SERIES C1 DRIVE ASSEMBLY PARTS LIST Key 14 Model Series Part Description C10, C Stroke dial 1 C Stroke dial 1 C Stroke dial 1 C Stroke dial 1 15 C Screw 4 16 C Pulser 1 17 C Retaining Ring 1 18 C101, C111, C121, C131, C Varistor Assembly, 115V 1 C102, C112, C122, C132, C142, C103, C113, C123, C133, C143, C105, C115, C125, C135, C145, C106, C116, C126, C136, C146, C107, C117, C127, C137, C Varistor Assembly, V 1 19 C102, C112, C122, C132, C Varistor Assembly, 230V US 1 21 C Housing 1 23 C O-Ring 2 24 C Collar 1 25 C Set Screw 1 26 C Screw, 10-24x C Ground Wire Assembly 1 28 C Washer, Conical 4 29 C Screw, 10-24X C Bracket (Without mating parts) 1 31 C Thermostat 1 32 C101, C111, C121, C131, C Power Cord Assembly, 115V 1 C102, C112, C122, C132, C Power Cord Assembly, 230V US 1 C103, C113, C123, C133, C Power Cord Assembly, 230V DIN 1 C105, C115, C125, C135, C Power Cord Assembly, 240V UK 1 C106, C116, C126, C136, C Power Cord Assembly, 250V AUST 1 C107, C117, C127, C137, C Power Cord Assembly, 230V SWISS 1 33 C Retaining Ring 1 34 C Washer 1 35 C Spring 1 36 C Pinion 1 37 C Gasket 1 38 C Shaft Assembly 1 Qty

7 SERIES C1 DRIVE ASSEMBLY PARTS LIST Key 39 Model Series Part Description C111, C121, C131, C EPU Assembly, 115V ( C101) 1 C112, C122, C132, C142, C113, C123, C133, C143, C115, C125, C135, C145, C116, C126, C136, C146, C117, C127, C137, C EPU Assembly, 230V ( C10X) 1 40 C EPU Sleeve 1 41 C Spacing Stud 2 42 C11, C Stud Assembly ( C10) 4 C13, C Stud Assembly 4 43 C O-Ring 1 44 C Shim 1 45 C Retaining Ring 1 46 C Screw, X 4.5 SS 4 47 C Spacer, 0.9 SI 1 C11, C Spacer, 1.8 SI 1 C13, C Spacer, 3.0 SI 1 48 C Seal 1 49 C Adapter, C Screw,10-24 X Qty

8 SERIES C1 CONTROL PANEL DETAIL SPEED LIGHT SPEED KNOB SPEED STROKE KNOB STROKE TURN WHILE UNIT IS RUNNING DATA PLATE DISCONNECT POWER CORD BEFORE REMOVING PANEL 50/60 HZ

9 SERIES C1 WIRING DIAGRAM POTENTIOMETER LED PULSER WHT OR BLU BLK OR BRN POWER CORD MOV GRN OR GRN/YEL YEL GRN OR GRN/YEL EPU ASSEMBLY YEL HOUSING WALL

10 We are a proud member of Accudyne Industries, a leading global provider of precision-engineered, process-critical, and technologically advanced flow control systems and industrial compressors. Delivering consistently high levels of performance, we enable customers in the most important industries and harshest environments around the world to accomplish their missions. sales@novatech-usa.com Tel: (866) Fax: (866) Tel: (281) Fax: (281) LMI is a registered trademark of Milton Roy, LLC. 1998, 2015 Milton Roy, LLC. Specification to change without notice. info@lmipumps.com