WARNING GATE LOCK MODEL SGLOCK12V
|
|
- Angel Maxwell
- 5 years ago
- Views:
Transcription
1 GATE LOCK MODEL SGLOC2V The SGLOC2V Automatic is compatible with LiftMaster Gate Access Systems LA412, LA412-S, and RSW operators. The purpose of the automatic gate lock is to securely lock the gate in the closed position. CART INVENTORY Watertight Connector (1) WARNING To avoid SERIOUS personal INJURY or DEATH from electrocution: Disconnect ALL electric and battery power BEFORE performing ANY service or maintenance. This device is for use LY with LiftMaster gate operator models LA412, LA412-S, and RSW operators. Read and follow ALL instructions. Have gate in full closed position BEFORE installing the gate lock. Pin Cable Ties (6) Keys (2) Label (1) (Not Shown) BEFORE STARTING Read and follow all instructions. Before getting started, check the carton inventory. Mounting hardware is not provided. Refer to a local hardware store for necessary mounting hardware. The gate lock is designed to use 5/16" diameter mounting hardware. For tubular gates, the following items are needed: Carriage bolts, washers, and nuts. For chain link gates, the following items will be needed: U-bolts, carriage bolts, washers, and nuts. Ensure that the gate closes properly. When the gate lock and gate bracket are properly aligned, the gate lock will latch onto the bracket pin. NOTE: Some installations may require the gate bracket to be recessed in the mounting post so the bracket and lock will be flush and lock properly. Instead of recessing the gate bracket, a spacer may be added between the lock and the gate. Size the spacer before attempting to mount the lock. If installing the gate lock on a Push-to-Open gate, the lock must be installed on the opposite side of the gate. Gate bracket must be Recessed so that the sits flush. Mounting Post PUSH-TO- GATE Open Spacer PULL-TO- GATE Spacer 1 Aligned Lock and Bracket
2 F9 6 J21 F1 Ø Q J J2Ø R42Ø R C69 AC PWR / RE CH CTRL PWR LOCK F9 F8 SOL MA R184 GND R1 C1Ø1 D J21 F1 R182 Ø Ø Q22 J LOCK / BIPART DELAY C7Ø C71 C72 C73 J S J2Ø C75 R42Ø R423 C69 J18 29 C66 F11 AC PWR / Q12 3 CH C65 Q6 Q1 CTRL RE C68 C33 PWR R184 S INSTALLATI NOTE: If the gate lock is being installed on a dual gate, the gate lock must be mounted on gate 1 (primary gate) and the bracket must be mounted on gate 2 (secondary gate). The lock/bipart delay switch on the operator will allow gate 1 to close first followed by gate Disconnect all power to the gate operator: 3ØA 32V J24 J23 3ØA 32V R329 7 R186 Disconnect batteries. Disconnect AC PWR/ connector. (SECDARY) (PRIMARY) Control Board F12 18 Q6 Q1 C68 C33 R186 Remove terminal block. 3ØA 32V J24 J23 3ØA 32V R329 7 AC PWR/ Battery Connections 2. Remove gate release pin to allow gate to swing freely during installation of gate lock. 3. Use a level to align the lock and bracket at the end of the gate. Gate Release Pin Level Gate Operator Arm Hairpin Clip 4. Mark and drill holes for gate bracket and gate lock. Holes Holes 2
3 NOTE: For chain link and other fencing, additional cross members may be needed to properly support the gate lock (see below). 5. Mount the bracket using purchased hardware. Hand tighten the nuts. 6. Insert the gate bracket pin through the gate bracket. Nuts Pin s Carriage Bolts 7. Slide washer over gate bracket pin. Insert cotter pin through the gate bracket pin and bend back the ends. 8. Mount the lock using purchased hardware. Pin 9. To ensure proper alignment, close gate and mate the lock with bracket and cotter pin. NOTE: Use the key to manually release the lock. TYPICAL IR OR ALUMINUM TUBE FENCE AND GATE INSTALLATI Pin TYPICAL CHAIN LINK FENCE AND GATE INSTALLATI Pin Carriage Bolts Carriage Bolts Carriage Bolts Carriage Bolts Additional Reinforcement Bolts, Nuts and s (Not Provided; Size of Fasteners Depends on the Gate) Bolts, Nuts and s (Not Provided) 3
4 R4 C2 N N T U 5 24 VAC/ INPUT MOV2 F4 F5 1 R35 D9 7 Z3 Q22 2 JMP JMPR1 D6 TO F6 C4 RE CTROL LOOP SHADOW INTERRUPT CH F1 20A 32V FUSE BATT 2 BATT 1 WIRING Connect Wire to the Control Box 1. Open the cover of the control box by loosening the four screws. Screws Control Box 2. Run the wire back to the control box. Use the cable ties to secure the wire to the gate. To Control Box Cable Ties NOTE: Make sure that the gate does not pinch, bind, or rub the wire. Make sure that the wire does not sag or touch the ground. Never run wire along the bottom edge of the gate between the gate and the ground. Cable Ties 3. Feed the wire into the control box through an available knockout located at the bottom of the control box. If necessary use a screwdriver and hammer to open a new knockout. 4. Insert watertight connector and tighten with watertight connector nut. Watertight Connector Nut Knockouts Watertight Connector Nut 4
5 23 EDGE ALARM Ø7 NO Z2Ø 27 C MAGLOCK EDGE/ NO 24 C NC 2 Z9 MAGLOCK R1 1 N 4 Ø N Z8 T 3 U S Ø CTROL TO N F4 N RE T F5 U 1 R35 D9 7 Z3 LOOP Q22 2 C4 SHADOW INTERRUPT 5 CH R4 C2 F6 24 VAC/ F1 20A 32V INPUT MOV2 FUSE BATT 2 BATT 1 JMP JMPR1 23 EDGE ALARM Ø7 NO Z2Ø 27 C MAGLOCK EDGE/ NO 24 C NC 2 Z9 MAGLOCK R1 1 N 4 Ø N Z8 T 3 U S Ø CTROL TO N F4 N RE T F5 U 1 R35 D9 7 Z3 LOOP Q22 2 C4 SHADOW INTERRUPT 5 CH R4 C2 F6 24 VAC/ F1 20A 32V INPUT MOV2 FUSE BATT 2 BATT 1 JMP JMPR1 D6 D6 Wiring to the Control Board 1. Connect the red wire to the SOL terminal of the LOCK connector. 2. Connect the black wire to the GND terminal of the LOCK connector. Reconnect gate operator arm to gate using gate release pin and hairpin clip. Red Black N LOCK R1 SOL GND Gate Release Pin MAG Gate Operator Arm Hairpin Clip Setting the Bipart Delay In some installations it may be necessary to delay the opening of the gate. This will allow enough time for the gate lock to activate and properly release the bracket pin. Dual Gate Installations Set the LOCK/BIPART DELAY to position to ensure the primary gate will open first and close last. Fast Opening Gates If you have a lighter gate that opens quickly you might need to set the LOCK/BIPART DELAY to position to ensure that the lock has enough time to activate before the gate starts moving. LOCK/ BIPART DELAY C7Ø C71 Single Gate Gate 2 Gate 1 Dual Gate 5
6 LOCK F9 F8 SOL GND MA R1 C1Ø1 D J21 F1 R182 Ø Ø Q22 J LOCK / BIPART DELAY C7Ø C71 C72 C73 J S J2Ø C75 R42Ø R423 C69 J18 29 C66 F11 AC PWR / Q12 3 CH C65 Q6 Q1 CTRL RE C68 C33 PWR R184 RECNECT 1. Reconnect all batteries. 2. Plug in AC or Solar input. F12 18 Q6 Q1 C68 C33 Control Board R186 RECNECT terminal block. R329 7 J24 J23 3ØA 32V 3ØA 32V AC PWR/ Battery Connections OPERATI 1. Manually open the gate lock using the key. 2. Use the remote control to open the gate. Manually close the gate lock by turning and removing the key. NOTE: The LOCK LED is on whenever the gate lock is opened. 3. Press the remote control button to return the gate to the closed position and make sure that the gate lock properly captures the gate bracket pin, locking the gate. 6
7 ALARM D36 0VLD EDGE/ SOL GND MA 2 C75 LOCK LOCK / BIPART DELAY 1 R1 Ø C7Ø 4 C71 C72 C F8 S CTRL PWR TO CTROL Ø RE 4 R184 LOOP Q22 SHADOW 29 INTERRUPT CH CTRL PWR R42Ø R423 F1 AC PWR / F9 6 C1Ø1 J21 R182 F12 J19 2 J J2Ø C69 J18 C66 C65 F11 C2 EDGE PROAMMING Reprogram Limits 1. Press the S button. 2. The LED will blink. 3. Use the buttons to move gate 1 to the desired open position. Repeat if gate 2 is present using buttons. 4. Press the S button to set the open limit for gate(s). 5. The LED will turn off. The LED will blink. 6. Use the buttons to move gate 1 to the desired close position. Repeat if gate 2 is present using buttons. 7. Press the S button to set the close limit for gate(s). 8. The LED will turn off. The limits are set. 9. Using programmed remote or single button control (SBC) run the gate(s) from the close limit to the open limit. After reaching the open limit, run the gate(s) to the close limit. This will learn the force in the open and close direction. Ø Ø 3ØA 32V BIPART BIPART DELAY DELAY J24 J23 3ØA 32V R329 7 C7Ø C7Ø C71 C71 C72 C72 C73 C73 R186 Q6 Q12 Q1 C68 C33 MOV2 R4 Control Board Control Box S R SECURE CTROL BOX Close control box cover and secure with the four screws. Screws Control Box 7
8 TROUESHOOTING NOTE: Follow these steps LY if the gate lock fails to activate properly. PROEM Gate lock does not activate. POSSIE SOLUTIS 1. Verify that all wiring is correct. 2. Check wiring connections. It is possible that a wire is inserted too far into a terminal block, grabbing the insulation instead of the copper wire. 3. Verify all the terminal blocks are properly seated on the control board. It is possible to offset these blocks by one position which can prevent correct operation. 4. Bracket pin may be binding and preventing the lock from properly sliding. Verify the bracket and gate lock are properly aligned. Verify that the gate lock can be manually opened with the key when the gate is closed. Do not push against the gate when manually opening the gate lock. Gate lock does not activate fast enough to release bracket pin in order to allow gate to open. 1. Gate may be moving too quickly for the gate lock to properly activate. Turn the Lock/Bipart delay to the position. 2. Bracket pin may be binding and preventing the lock from properly sliding. Verify the bracket and gate lock are properly aligned. Verify that the gate lock can be manually opened with the key when the gate is closed. Do not push against the gate when manually opening the gate lock. 3. Check wiring connections. A loose connection may cause intermittent operation of the gate lock, delaying its response to activate properly. Gate reverses unexpectedly. 1. Ensure there are no obstructions impeding the travel of the gate. 2. Reprogram limits as described on page Readjust force setting according to the operator owner s manual. FOR TECHNICAL SUPPORT CALL OUR TOLL FREE NUMBER: , The Chamberlain Group, Inc B All Rights Reserved
K001A6039. Control Board Replacement Kit WARNING INSTALLATION INSTRUCTIONS APPLICATION REQUIREMENTS: FUNCTION: REMOVE EXISTING BOARD
ontrol Board Replacement Kit APPLIATI REQUIREMENTS: This modification is available to all LA400 North American gate operators. FUTI: Allows existing LA400 control board in the field to be replaced or upgraded
More informationLA412 & LA412-S O W N E R ' S M A N U A L 12 VOLT DC SINGLE SOLAR RESIDENTIAL GATE OPERATOR FOR RESIDENTIAL USE ONLY 2 YEAR WARRANTY
LA & LA-S VOLT DC SINGLE SOLAR RESIDENTIAL GATE OPERATOR O W N E R ' S M A N U A L FOR RESIDENTIAL USE ONLY Please read this manual and the enclosed safety materials carefully! Periodic checks of the operator
More informationLA400 & LA400-S O W N E R ' S M A N U A L MEDIUM DUTY SWING GATE OPERATOR. Large Metal Control Box (XLM) Optional 2 YEAR WARRANTY
LA400 & LA400-S MEDIUM DUTY SWING GATE OPERATOR O W N E R ' S M A N U A L Large Metal Control Box (XLM) Optional Serial # Primary Arm Serial # Secondary Arm Serial # Control Box Installation Date The LA400
More informationTABLE OF CONTENTS SAFETY SAFETY SYMBOL AND SIGNAL WORD REVIEW SAFETY 1 OPERATION 31 INTRODUCTION 5 ACCESSORY WIRING 34 INSTALLATION 9 MAINTENANCE 36
TABLE OF CONTENTS SAFETY 1 SAFETY SYMBOL AND SIGNAL WORD REVIEW...1 USAGE CLASS...2 UL325 ENTRAPMENT PROTECTION REQUIREMENTS...2 SAFETY INSTALLATION INFORMATION...3 GATE CONSTRUCTION INFORMATION...4 INTRODUCTION
More informationPhotoelectric. Sensors Invisible Light Beam Protection Area
COMMERCIAL PROTECTOR SYSTEM MODELS CPS-U AND CPS-UN4 To prevent possible SERIOUS INJURY or DEATH from a closing gate or door: Entrapment protection devices MUST be installed per the operator owner's manual.
More informationINSTALLATION MANUAL MODEL LA412 RESIDENTIAL DC SOLAR VEHICULAR SWING GATE OPERATOR. UL991 compliant. UL325 compliant. LA4121PKGDC Single Arm Package
RESIDENTIAL DC SOLAR VEHICULAR SWING GATE OPERATOR MODEL LA412 LA4121PKGDC Single Arm Package LA412DC Primary 12 VDC Actuator Arm for single swing gate applications LA412DCS Secondary 12 VDC Actuator Arm
More informationAUTOMATIC GATE LOCK. Installation Manual
IMPORTANT: Before you install the automatic gate lock be sure your gate is level, moves freely on its hinges, and does not bind or drag against the ground. AUTOMATIC GATE LOCK Installation Manual PLEASE
More informationINSTALLATION MANUAL MODEL LA500 LIGHT COMMERCIAL - RESIDENTIAL DC VEHICULAR SWING GATE OPERATOR. UL991 compliant. UL325 compliant
LIGHT COMMERCIAL - RESIDENTIAL DC VEHICULAR SWING GATE OPERATOR MODEL LA500 LA5001PKGDC Single Arm Package LA500DC Primary 24 VDC Actuator Arm for single swing gate applications LA500DCS Secondary 24 VDC
More informationYG101 SWING GATE OPENER OWNER S MANUAL
YG101 SWING GATE OPENER OWNER S MANUAL IMPORTANT SAFTEY INFORMATION Installing the YG101 Gate Opener requires wiring of standard 110V electrical lines. This should only be performed by a trained technician.
More informationLA500 & LA500-S VEHICULAR SWING GATE OPERATOR INSTALLATION MANUAL
LA00 & LA00-S VEHICULAR SWING GATE OPERATOR INSTALLATION MANUAL Your model may look different than the model illustrated in this manual. THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS
More informationINSTALLATION AND OPERATING INSTRUCTIONS For Model GL1 Gate Locks
Securitron Magnalock Corp. Tel 775.355.5625 550 Vista Boulevard Fax 775.355.5633 Sparks, NV 89434 info@securitron.com www.securitron.com ASSA ABLOY, the global leader in door opening solutions INSTALLATION
More informationSKC400U SLIDING GATE OPENER OWNER S MANUAL
SKC400U SLIDING GATE OPENER OWNER S MANUAL IMPORTANT SAFTEY INFORMATION Installing the SKC400U Gate Opener requires wiring of standard 110V electrical lines. This should only be performed by a trained
More informationMODEL SW420 LIGHT-DUTY RESIDENTIAL SWING GATE OPERATOR
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com MODEL SW420 LIGHT-DUTY RESIDENTIAL SWING GATE OPERATOR OWNER S MANUAL Intended for professional installation
More informationADDENDUM MODEL S3 OPERATORS Models: SL/540/570/580/590 & SW420/470/490
ADDENDUM MODEL S3 OPERATORS Models: SL/540/570/580/590 & SW420/470/490 This addendum is to be used in conjunction with the owner s manual included with this operator. Refer to this addendum for all programming
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
0 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) / Replacement Motor Key (00KEY) Rod
More informationMODEL SL575 HEAVY DUTY SLIDE GATE OPERATOR
CTROLLER BOARD GL MODEL SL575 HEAVY DUTY SLIDE GATE OPERATOR 2 YEAR WARRANTY Serial # (located on electrical box cover) Installation Date MODEL SL575 IS FOR VEHICULAR PASSAGE GATES LY AND IS NOT INTENDED
More informationLA500 & LA500-S VEHICULAR SWING GATE OPERATOR INSTALLATION MANUAL
LA00 & LA00-S VEHICULAR SWING GATE OPERATOR INSTALLATION MANUAL Your model may look different than the model illustrated in this manual. THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS
More informationMODEL SL585 MODEL SL595 HEAVY DUTY SLIDE GATE OPERATOR HEAVY DUTY, HARSH ENVIRONMENT SLIDE GATE OPERATOR 2 YEAR WARRANTY CONTROLLER BOARD
CTROLLER BOARD GL MODEL SL585 HEAVY DUTY SLIDE GATE OPERATOR YEAR WARRANTY Serial # (located on electrical box cover) Installation Date MODEL SL595 HEAVY DUTY, HARSH ENVIRMENT SLIDE GATE OPERATOR MODELS
More informationASSA ABLOY Series Power Operator Installation and Instruction ASSA Manual ABLOY ASSA ABLOY
00 Series Power Operator Installation and Instruction ASSA Manual ABLOY Item No. Description Motor (00M) Cover (00COV) Control Inverter (00IN) Power Supply VDC (00PS) Track Assembly (0-) / Replacement
More informationNOTE: Refer to hardware list provided to identify fasteners supplied. Figure 2-1
NOTE: Read all instructions carefully, checking shop drawings supplied for any special conditions. Open all crated materials and check for damaged or missing parts prior to installation. NOTE: Proper operation
More informationE-S Allegiant Series Single Swing and Dual Swing Gate Opener
Estate Swing brand gate openers are a Sequoia Brands, Inc. product. Please visit www.estateswing.com for manual updates and other product information This gate opener is low voltage and bolt on specifically
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Door Openings 85 to 0 or to 80 Adjustable Arm and Slide Track Application Maximum Hinge Side Frame Reveal to /8 (mm) Hinge (Pull) Side of Door Installation 5700 LEO
More informationElectric Lock Part List
When the length of your gate is more than 1.5 meters, we recommend installing an Electric Lock. An electric lock provides extra security and stability to your gate system. The lock provides extra protection
More informationRequirements LEO Power Operator Installation Instructions Patents: 5,881,497; 7,316,096; 7,484,333 CAUTION CAUTION WARNING
CAUTION 80-957-00-00 (08-0) Series 570 Openings 85 to 0 or to 70 Double Lever Arm Application for Frame Reveals (76) to 7 (78mm)* Stop (Push) Side of Installation 5700 LEO Operator Installation Instructions
More informationINDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR
INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR INSTALLATION MANUAL H, J, AND HJ GH T AND APT GT THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED DOOR SYSTEMS TECHNICIAN ONLY. Operators are shipped in
More informationMEDIUM DUTY DOOR OPERATOR MODELS MT5011U & BMT5011U
MEDIUM DUTY DOOR OPERATOR MODELS MT0U & BMT0U INSTALLATION MANUAL Now with Built in Radio Receiver MHz Your model may look different than the model illustrated in this manual. YEAR WARRANTY Serial # (located
More informationPREMIUM Series 1/2 hp Chain Drive Garage Door Opener
.. PREMIUM Series 1/2 hp Chain Drive Garage Door Opener Model 8365-267 FOR RESIDENTIAL USE ONLY Please read this manual and the enclosed safety materials carefully! Fasten the manual near the garage door
More information54531/ FORD FUSION
54531/51531 54531/51531 13-15 FORD FUSION 13-15 FORD FUSION FORD FUSION Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill
More informationMODEL SL575 HEAVY DUTY SLIDE GATE OPERATOR
CTROLLER BOARD GL MODEL SL575 HEAVY DUTY SLIDE GATE OPERATOR 2 YEAR WARRANTY Serial # (located on electrical box cover) Installation Date MODEL SL575 IS FOR VEHICULAR PASSAGE GATES LY AND IS NOT INTENDED
More informationDigitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers
Supersedes IL 33-858-4 Dated 05/02 Digitrip Retrofit System for ITE K-3000, K-3000 S, K-4000 and K-4000 S Breakers Digitrip Retrofit System for ITE K-3000, Digitrip Retrofit System for ITE K-3000, K-3000
More informationINSTALLATION INSTRUCTIONS AND OPERATION MANUAL
INSTALLATION INSTRUCTIONS AND OPERATION MANUAL FS Series Rolling Fire Door Operators CORPORATION GENERAL NOTES TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS
More informationTABLE OF CONTENTS SAFETY SAFETY SYMBOL AND SIGNAL WORD REVIEW SAFETY 1 ACCESSORY WIRING 29 INTRODUCTION 5 EXPANSION BOARD 31 INSTALLATION 9
TABLE OF CONTENTS SAFETY 1 SAFETY SYMBOL AND SIGNAL WORD REVIEW...1 USAGE CLASS...2 UL325 ENTRAPMENT PROTECTION REQUIREMENTS...2 SAFETY INSTALLATION INFORMATION...3 GATE CONSTRUCTION INFORMATION...4 INTRODUCTION
More informationMODEL SW470 MEDIUM DUTY SWING GATE OPERATOR
CTROLLER BOARD GL MODEL SW470 MEDIUM DUTY SWING GATE OPERATOR MODEL SW490 HEAVY DUTY SWING GATE OPERATOR 2 YEAR WARRANTY Serial # (located on electrical box cover) Installation Date INTENDED FOR PROFESSIAL
More informationMODEL SW470 MODEL SW490 MEDIUM DUTY SWING GATE OPERATOR HEAVY DUTY SWING GATE OPERATOR 2 YEAR WARRANTY CONTROLLER BOARD
CTROLLER BOARD GL MODEL SW470 MEDIUM DUTY SWING GATE OPERATOR MODEL SW490 HEAVY DUTY SWING GATE OPERATOR 2 YEAR WARRANTY Serial # (located on electrical box cover) Installation Date INTENDED FOR PROFESSIAL
More informationSAVE THESE INSTRUCTIONS
READ AND FOLLOW ALL SAFETY INSTRUCTIS! SAVE THESE INSTRUCTIS AND DELIVER TO OWNER AFTER INSTALLATI IMPORTANT SAFEGUARDS! When using electrical equipment, basic safety precautions should always be followed
More informationINSTRUCTION MANUAL 16K - Fifth Wheel Hitch
You can take it with you. INSTRUCTION MANUAL 16K - Fifth Wheel Hitch Product No. 30047 DEALER/INSTALLER: END USER: (1) Provide this Manual to end user. (2) Physically demonstrate hitching and unhitching
More informationRESIDENTIAL DC VEHICULAR SWING GATE OPERATOR
RESIDENTIAL DC VEHICULAR SWING GATE OPERATOR INSTALLATION MANUAL Model RSW12U THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. This model is for use on vehicular
More informationILM16 ILM20 ILM30 ILM12AF ILM16AF ILM20AF ILM30AF
ILM Series Liftgates Read Before Installing INSTALLATION MANUAL For Models: ILM12 ILM16 ILM20 ILM30 ILM12AF ILM16AF ILM20AF ILM30AF Interlift, Inc. a Subsidary of MBB Liftsystems AG 15939 Pluma Avenue
More informationInstallation Manual for the. Automatic Gate Operator
Installation Manual for the Automatic Gate Operator WARNING! This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 (UL 325). However, gate
More informationRemember to keep all receipts for proof of purchase.
UL325 SERIES 1-800-543-GATE (4283) www.mightymule.com 1. KEEP CLEAR! Gate may move at any time. 2. Do not allow children to operate gate or play in gate area. 3. This gate is for vehicles only. Pedestrians
More informationAutomatic Gate Lock Installation Manual
IMPORTANT: Before you install the automatic gate lock be sure your gate is level, moves freely on its hinges, and does not bind or drag against the ground. Automatic Gate Lock Installation Manual PLEASE
More informationFUNCTION: Allows existing Logic Control Version 2.0 or 2.0 Rev. B board in field to be replaced with new Logic Control Version 2.0 Rev. B.
LOGIC CTROL VER. 2.0 Rev. B PCB BOARD REPLACEMENT KIT APPLICATI REQUIREMENTS: This modification is available to models T, GT, APT, J, H, GH, SD and GSD standard door operators with Logic Control Board
More informationJEEVES. JEEVES Installation Manual. Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market
1 888-323-8755 www.nwlifts.com JEEVES Installation Manual The Easiest Do-It-Yourself Dumbwaiter on the Market This manual will cover the installation procedure step-by-step. The installation of this dumbwaiter
More informationGARAGE DOOR OPENER Model 3800
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.liftmaster.com GARAGE DOOR OPENER Model 3800 For Residential Sectional Doors With Torsion Assemblies Only Compatible with
More information54531/ FORD FUSION
2014-2015 FORD Upper Class Grille w/ Bars TOOLS REQUIRED: Socket Set Flat/Phillips Screw Drivers Torx Bits Plastic Pry Bar 3/16 Drill Bit and Drill Motor PARTS LIST: (4) #8 u-nuts (2) seal brackets (driver
More informationAC Powered. AC Powered. Model Installation/Owner s Manual. UL 325 Compliant. AC Powered Vehicular Swing Gate Operator
Installation/Owner s Manual Model 652-080 AC Powered Vehicular Swing Gate Operator Use this manual for circuit board 100-010 Revision AA or higher. EXTERNAL ENTRAPMENT PROTECTI MUST be installed or the
More informationChain Drive Garage Door Opener Model 8360 FOR RESIDENTIAL USE ONLY
. Write down the following information for future reference: Serial Number: Chain Drive Garage Door Opener Model 8360 FOR RESIDENTIAL USE ONLY Please read this manual and the enclosed safety materials
More informationInstallation Instructions
Installation Instructions ELECTRIC CONVERSION KIT 3 ALUMINUM ROLL TUBE IMPORTANT: This Electric Conversion Kit has been designed for systems with a 3 aluminum roll tube. It is assumed that the tarping
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationINSTALLATION INSTRUCTIONS AND OPERATION MANUAL
INSTALLATION INSTRUCTIONS AND OPERATION MANUAL FS Series Rolling Fire Door Operators UL325-2010 Compliant Restricted Duty Operators CORPORATION IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the
More information»Product» Safety Warning
D2300 Installation Instructions 2006-2011 Dodge Ram 1500 4WD 2.5" Adventure Series Suspension System Read and understand all instructions and warnings prior to installation of product and operation of
More informationTechnical Support (707)
Installation Instructions UNIMATIC SHIFTER Fits: GM, Powerglide, Ford and Chrysler Transmissions See Application Guide for Specific Vehicles Catalog # 80775 WORK SAFELY! For maximum safety, perform this
More informationGARAGE DOOR OPENER ASSEMBLY/ INSTALLATION MANUAL
The Chamberlain Group, Inc. 845 Larch Avenue Elmhurst, Illinois 60126-1196 www.chamberlain.com GARAGE DOOR OPENER ASSEMBLY/ INSTALLATION MANUAL Please read this manual and the enclosed safety materials
More informationInstallation Manual for the
1-800-543-GATE (4283) www.gtopro.com 1-800-543-GATE (4283) www.gtopro.com Installation Manual for the DUAL Gate Operator System FOR PROFESSIAL INSTALLATI LY! WARNING! This equipment is similar to other
More informationRESIDENTIAL DC VEHICULAR SLIDE GATE OPERATOR
RESIDENTIAL DC VEHICULAR SLIDE GATE OPERATOR INSTALLATION MANUAL Model RSL12UL THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. This model is for use on vehicular
More informationINSTALLATION INSTRUCTIONS AND OPERATION MANUAL
INSTALLATION INSTRUCTIONS AND OPERATION MANUAL Cornell RG Operator RGRL Series (w/ Internal Interlock sensor) ES 10-288 GENERAL NOTES TO REDUCE THE RISK OF SEVERE INJURY OR DEATH, READ AND FOLLOW ALL INSTALLATION
More informationInstallation Manual for the
1-800-543-GATE (4283) www.gtopro.com Installation Manual for the SINGLE Gate Operator System FOR PROFESSIAL INSTALLATI LY! WARNING! This equipment is similar to other gate or door equipment and meets or
More informationOWNER S MANUAL MODEL SW470 MEDIUM DUTY SWING GATE OPERATOR MODEL SW490 HEAVY DUTY SWING GATE OPERATOR
CTROLLER BOARD GL OWNER S MANUAL MODEL SW470 MEDIUM DUTY SWING GATE OPERATOR MODEL SW490 HEAVY DUTY SWING GATE OPERATOR MODEL SW470 MODEL SW490 MODELS SW470 AND SW490 ARE FOR VEHICULAR PASSAGE GATES LY
More informationLogic 5.0 Commercial Door Operator INSTALLATION MANUAL
Logic 5.0 Commercial Door Operator INSTALLATION MANUAL Models T, APT, H, J, HJ, GH, and GT NOT FOR RESIDENTIAL USE Please read this manual and the enclosed safety materials completely, prior to installation
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2010, 2000 by B&M Racing & Performance Products The B&M Unimatic is a universal shifter that will
More informationHAZARDOUS (NEMA 7/9) INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR 2 YEAR WARRANTY. Serial # Box. Installation Date. Wiring Type
O W N E R S M A N U A L HAZARDOUS (NEMA 7/9) INDUSTRIAL DUTY COMMERCIAL DOOR OPERATOR 2 YEAR WARRANTY Serial # Box Installation Date Wiring Type TABLE OF CONTENTS SPECIFICATIONS Operator Dimensions.................................
More informationECO# 1801 REVISION# 000 ES DATE
SmokeShield Elevator ECO# 1801 REVISION# 000 ES 10-458 DATE 08/25/2018 ECO# 1801 REVISION# 000 ES 10-458 DATE 08/25/2018 Section 1 Table of Contents Section 2 Safety Check List 2 Section 3 Freight Receiving
More informationInstallation/Owner s Manual Model 9050
8 CLASS HP MODEL VOLTS PHASE AMPS 0 Hz MAX GATE LOAD DoorKing, Inc., Inglewood, CA Installation/Owner s Manual Model 900 Use this manual for circuit board 70-00 Revision AA or higher. Vehicular Slide Gate
More informationInstallation Manual. for installing the GTO/PRO SW-3200XL with the GTO/PRO SW-3000XL in a dual application FOR PROFESSIONAL INSTALLATION ONLY!
Installation Manual for installing the GTO/PRO SW-3200XL with the GTO/PRO SW-3000XL in a dual application DC-SERIES DC-SERIES FOR PROFESSIAL INSTALLATI LY! WARNING! This equipment is similar to other gate
More informationTRAIL CHARGER with EXTENDER and COMBO NOSE BOX
TRAIL CHARGER with EXTENDER and COMBO NOSE BOX 284424 01 Version 1.02 03/14/2011 Owners Manual Operation Installation Wiring Diagram Troubleshooting Parts Breakdown 1 GENERAL OPERATION PROBLEM On applications
More informationLOGIC 5.0 DRUM BRAKE KIT INSTRUCTIONS FOR MODELS: T, J AND H K71-D1PH, K71-D3PH, AND K71-D575-1
LOGIC 5.0 DRUM BRAKE KIT INSTRUCTIONS FOR MODELS: T, J AND H K71-D1PH, K71-D3PH, AND K71-D575-1 APPLICATION This wiring modification is available for models T, J and H (for 1 Phase, 3 Phase and 575V Logic
More informationPFadvantage JD 3300/4400/6600/7700; 4420
Ag Leader Technology Combine Installation JD 33//66/77; 2 Note: Indented items indicate parts included Quantity by Model in an assembly listed above Early Late Part Name/Description Part Number 3 3 6 6
More informationMODEL LA100 LIGHT-DUTY RESIDENTIAL DC ACTUATOR GATE OPERATOR OWNER S MANUAL
The Chamberlain Group, Inc. 300 Windsor Drive Oak Brook, IL 60523 www.liftmaster.com MODEL LA100 LIGHT-DUTY RESIDENTIAL DC ACTUATOR GATE OPERATOR OWNER S MANUAL RESIDENTIAL USE ONLY Please read this manual
More informationSet Up instructions DB30 Doodlebug Removal from crate
Set Up instructions DB30 Doodlebug Removal from crate 1. Remove carton top 2. Remove set up instuctions, owners manual and parts. E - REV - B Hardware and Parts Front fork assembly Hardware 10mm Front
More informationGeneral Information. Notations and Conventions. Compatibility Check. Kit Description. Call-Outs. Part Lists Great Plains Manufacturing, Inc.
Part Lists Great Plains Manufacturing, Inc. 1 Installation Instructions Loup Shaft Monitor Used with Drill models: Compatible with most 1995 and later, two- and three-box drills with 5 8 -inch square main
More informationFlow Line Controls. Installation & Operations Manual SERIES 20/21 Pneumatic Actuators
Flow Line Controls Installation & Operations Manual SERIES 20/21 Pneumatic Actuators Flow Line Controls, Inc. P.O. Box 677 Schriever, LA 70395 Phone: 985-414-6003 Toll Free 1-800-815-9226 Fax 985-414-6072
More informationInstallation/Owner s Manual
CLASS MODEL SERIAL 8 HP DoorKing, Inc., Inglewood, CA Installation/Owner s Manual Use this manual for circuit board 0-00 Revision AA or higher. EXTERNAL ENTRAPMENT PROTECTI MUST be installed or the gate
More informationINSTALLATION & OWNER S MANUAL
Rev. A, p. 1 of 13 INSTALLATION & OWNER S MANUAL Polaris Ranger (2009-) Straight UTV Steel Plow with Vehicle Mount Kit 6 Wide Snow Plow (p/n: 1POLSP) (fits the 500 H.O., 700 & 800 HD & XP) The contents
More information115 VAC Control Boxes for
CLASS MODEL SERIAL 8 HP DOORKING CLOSE Wiring / Owner s Manual Use this manual for circuit board 0-00 Revision AA or higher. EXTERNAL ENTRAPMENT PROTECTI MUST be installed or the gate operator WILL NOT
More informationAC Powered. AC Powered. Model Installation/Owner s Manual. AC Powered Vehicular Swing Gate Operator. UL 325 August 2018 Standard
Installation/Owner s Manual Model 6524-380 AC Powered Vehicular Swing Gate Operator Use this manual for circuit board 4100-018 Revision A or higher. Entrapment Protection must be provided for the gate
More informationInstallation Instructions Unimatic Shifter
Installation Instructions Unimatic Shifter Universal Shifter for Automatic Transmissions Part Number 80775 2000 by B&M Racing & Performance Products LLC The B&M Unimatic is a universal shifter that will
More informationINSTALLATION INSTRUCTIONS AND OPERATION MANUAL
INSTALLATION INSTRUCTIONS AND OPERATION MANUAL Commercial and Industrial Fire Door Operator Logic Control Restricted Duty Fire Door Operators IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk
More informationINSTALLATION INSTRUCTIONS AND OPERATION MANUAL
INSTALLATION INSTRUCTIONS AND OPERATION MANUAL UL325-2010 Compliant Commercial and Industrial Door Operator Logic Control Continuous Duty IMPORTANT INSTALLATION INSTRUCTIONS WARNING To reduce the risk
More informationAutomatic Electronic Sport Mode Shifter Installation Instructions
Automatic Electronic Sport Mode Installation Instructions Building American Quality With A Lifetime Warranty! TOLL FREE 1-877-469-7440 tech@lokar.com www.lokar.com Release Automatic Electronic Sport Mode
More informationAVERTISSEMENT ATTENTION AVERTISSEMENT
SOLR PNEL INSTLLTION GUIDE MODEL SP10W12V & SP12V BEFORE STRTING WRNING Read and follow all instructions. Disconnect LL power and batteries to the operator. Do not connect batteries until instructed. CUTION
More informationInstallation/Owner s Manual Series 6500
Installation/Owner s Manual Series 00 Use this manual for circuit board 0-00 Revision E or higher. EXTERNAL ENTRAPMENT PROTECTI MUST be installed or the gate operator WILL NOT function. Vehicular Swing
More informationInstallation Instructions Z-Gate Shifter
Installation Instructions Z-Gate Shifter Part Number 80681 1998, 2001 by B&M Racing and Performance Products The B&M Z-Gate shifter can be used in vehicles equipped with most popular three speed automatic
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:
B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 66748 P:620.473.3664 F:620.869.903 Ford OEM Mount System Installation Instructions 20,000
More informationINSTALLATION INSTRUCTIONS
AUTOMOTIVE PRODUCTS, INC. INSTALLATION INSTRUCTIONS ULTIMATE BULL BAR APPLICATION: 2017 Ford F-250/350 PART NUMBER: 32-3900, 32-3905, 32-3900L, 32-3905L ITEM QUANTITY DESCRIPTION TOOLS NEEDED 1 1 ULTIMATE
More informationHYPPOETL HYPPO DUALETL 12 VOLT DC Swing Gate Operator
HYPPOETL HYPPO DUALETL 12 VOLT DC Swing Gate Operator Manufactured by NICE SpA INSTALLATION MANUAL 08/10 CONTENTS IMPORTANT SAFETY INSTRUCTIONS... 3 Applications...... 4 Pre-Installation Checklist... 5
More informationAUTOMATIC GATE OPENER
AUTOMATIC GATE OPENER Part # 7001282.001 Rev.A INSTALLATION MANUAL Model G752 For Double Gates AUTOMATIC GATE OPENER Installation Manual GATE OPENER CLASS CATEGORIES* The Zareba Automatic Gate Opener is
More informationMODEL 3002xTJ32 ELECTROMAGNETIC LOCK INSTALLATION INSTRUCTIONS
The Series 3002xTJ32 is a 1500 pound holding force top jamb mounted electromagnetic lock designed to secure a double inswing door. The lock requires both installation procedures as described herein and
More informationCOOKSON OWNER S MANUAL
COOKSON OWNER S MANUAL ELECTRIC CLUTCH RELEASE FOR TUBULAR MOTOR 3117(1) ECN 0951 BY RG 10/28/10 1 PATENT NO. 6,155,324 SPECIFICATIONS ELECTRICAL SPECIFICATIONS TUBULAR MOTOR FOR TUBULAR MOTOR ELECTRICAL
More informationInstallation Manual FM502 WARNING!
Installation Manual FM502 WARNING! This equipment is similar to other gate or door equipment and meets or exceeds Underwriters Laboratory Standard 325 (UL 325). However, gate equipment has hazards associated
More informationPOLARIS 4500 HD WINCH KIT
POLARIS 4500 HD WINCH KIT P/N 2883860 APPLICATION Verify accessory fitment at Polaris.com. BEFORE YOU BEGIN Read these instructions and check to be sure all parts and tools are accounted for. Please retain
More information<THESE INSTRUCTIONS MUST BE GIVEN TO THE END USER> B&W Trailer Hitches 1216 Hawaii Road / PO Box 186 Humboldt, KS P: F:
B&W Trailer Hitches 26 Hawaii Road / PO Box 86 Humboldt, KS 6678 P:620.73.366 F:620.869.903 Ford OEM Mount System Installation Instructions 20,000 LBS.
More informationGENERAL SAFETY... 3 PARTS LIST...
Rev 17a 1 GENERAL SAFETY... 3 PARTS LIST... 4 GTR100... 4 GTR058... 5 TECHNICAL SPECIFICATIONS... 6 FEATURES:... 6 QUICK INSTALLATION GUIDE... 7 GATE ARM INSTALLATION... 8 BEFORE YOU START... 8 INSTALLATION
More informationOWNER S MANUAL MODEL NO. MEDIUM DUTY JACK SHAFT OPERATOR MDJ, MDJH, MDJB, MDJBH READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS SAVE THESE INSTRUCTIONS
OWNER S MANUAL MEDIUM DUTY JACK SHAFT OPERATOR MODEL NO. NOT FOR RESIDENTIAL USE READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS SAVE THESE INSTRUCTIONS This unit is intended for limited duty applications
More informationCOOKSON OWNER'S MANUAL
COOKSON OWNER'S MANUAL FDO-A10 INDUSTRIAL DUTY FIRE DOOR OPERATOR R L I S T E D 3040233 US CONTROL PANEL SERIAL# OPERATOR SERIAL# 9001.DWG ECN 0959 REV 4 SPECIFICATIONS MOTOR TYPE:...INTERMITTENT HORSEPOWER:...1/8
More informationMEDIUM DUTY DOOR OPERATOR MODELS MJ5011U, MH5011U, MHS5011U, & MGJ5011U
MEDIUM DUTY DOOR OPERATOR MODELS MJ0U, MH0U, MHS0U, & MGJ0U INSTALLATION MANUAL Now with Built in Radio Receiver MHz Your model may look different than the model illustrated in this manual. YEAR WARRANTY
More informationInstallation Manual. Models
Installation Manual Models 8160 8165 8065 8075 FOR RESIDENTIAL USE ONLY Please read this manual and the safety materials carefully! The door WILL NOT CLOSE unless the Protector System is connected and
More informationAssembly Instructions. General Information. Installation Instructions. 12, 15 and 20 Series Drill Small Seeds Option. Used with:
Installation Instructions! Used with: 1200, 1210 and 1220 Drills 1500, 1510 and 1520 Drills 2000, 2010 and 2020 Drills 12, 15 and 20 Series Drill Small Seeds Option When you see this symbol, the subsequent
More informationLMPLC COOKSON OWNER'S MANUAL FDO A & B SOLID STATE INDUSTRIAL DUTY FIRE DOOR OPERATOR. B2/C2 Wiring 2 YEAR WARRANTY FDO 1/2 HP FDO A & B
COOKSON OWNER'S MANUAL FDO A & B SOLID STATE INDUSTRIAL DUTY FIRE DOOR OPERATOR LMPLC CONTROL LMPLC CONTROL WIRED B/C Wiring FDO / HP FDO A & B FDO HP FDO A & B YEAR WARRANTY Serial # (located on electrical
More informationRESIDENTIAL DC VEHICULAR SWING GATE OPERATOR
RESIDENTIAL DC VEHICULAR SWING GATE OPERATOR INSTALLATION MANUAL Model RSW12UL THIS PRODUCT IS TO BE INSTALLED AND SERVICED BY A TRAINED GATE SYSTEMS TECHNICIAN ONLY. This model is for use on vehicular
More informationOwner s Manual. Model 9100 Vehicular Slide Gate Operator
Owner s Manual Model 9100 Vehicular Slide Gate Operator DoorKing, Inc. 120 Glasgow Avenue Inglewood, California 90301 U.S.A. Phone: 310-645-0023 Fax: 310-641-1586 www.doorking.com P/N 9100-065 REV C, 1/04
More information