BlueHeat Coolant Heater
|
|
- Jesse Bradley
- 5 years ago
- Views:
Transcription
1 BlueHeat Coolant Heater Thermo Top Ford F-50/350 Super Duty 6.4 Liter TT Diesel 6.8 Liter V0 Gasoline Beginning Model Year: 008 Special instructions for these models Part locations may differ slightly dependent on the vehicle model. Special Tools Hose Clamping pliers Torque Wrench Table of Contents Foreword Parts List 3 Vehicle Information 3 Scope and Purpose 3 Symbol Identification 4 General References 5 Preparation 5 Heater Installation Site 5 Installation Electrical - Overview 6 Electrical Harness Installation 7 Timer Installation 7 Fuse Tap Connection - Relay K- 8 Integration into the Blower System 8 3-Relay HVAC Harness Connections 9 K3 Relay Ground 0 Heater Control and Fuel Pump Harness Routing 0 Heater Preparation and Installation Heater Mounting Exhaust Installation Integration into the Coolant System Liter TT Diesel 3 Coolant Hose Connections Liter TT Diesel 4 Integration into the Coolant System Liter V0 Gasoline 5 Coolant Hose Connections Liter V0 Gasoline 6 Combustion Air Intake Installation 8 Integration into the Fuel System 9 Fuel Pump Installation 9 Fuel Line and Fuel Pump Harness Routing 0 Standpipe Installation Liter TT Diesel Standpipe Installation Liter V0 Gasoline Power Connection 4 Ground Connection 4 Final Inspection, Initial Start-up and Concluding Work 5 Heater Lockout Reset Procedure 6 Electrical Harness Schematic - Part 7 Electrical Harness Schematic - Part 8 Heater Plumbing Schematic - Inline Method 9 DOC P/N B KIT P/N C Printed in USA Webasto Product N.A., Inc.
2 Warning Improper installation or repair of Webasto heating and cooling systems can cause fire or the leakage of deadly carbon monoxide leading to serious injury or death. Installation and repair of Webasto heating and cooling systems requires special Webasto training, technical information, special tools and special equipment. NEVER attempt to install or repair a Webasto heating or cooling system unless you have successfully completed the factory training course and have the technical skills, technical information, tools and equipment required to properly complete the necessary procedures. ALWAYS carefully follow Webasto installation and repair instructions and heed all WARNINGS. Webasto rejects any liability for problems and damage caused by the system being installed by untrained personnel or by improper installation. Improper installation or installation by untrained personnel voids all warranties on this product. If there are any questions regarding the installation or maintenance of this product, please call technical support at
3 Ford F-50/350 Super Duty Truck BlueHeat TM Parts List Quantity Part Part Number Heater Kit L Diesel or Heater Kit L Gasoline 50035A C Installation Kit C Vehicle Information Manufacturer Model Year Engine Type Ford F-50/350 Super Duty Beginning Model Year: Liter Diesel and 6.8 Liter Gasoline Foreword The installation and service of Webasto Thermo Top series (BlueHeat) heaters requires special expertise and training. Installations and servicing of Webasto products by untrained, unauthorized personnel and end-users voids all warranties and releases Webasto Product North America, Inc. and Webasto authorized distributors, dealers and their personnel from responsibility for damage to Webasto products, any resulting collateral property damage and personal injury. Any use, operation, installation, modification or application of the product not described in Webasto manuals, or subjecting the product to extreme or unusual conditions beyond the limits of specified performance characteristics is misuse of the product. Failure to comply with all installation instructions is a misuse of Webasto products. The same applies for repairs without using genuine Webasto service parts. This will void the coolant heaters official Marks of Conformity. Scope and Purpose These installation instructions are intended to support Webasto trained and authorized distributors and dealers in the installation of the Thermo Top series (BlueHeat) Coolant Heaters. These instructions are not intended for use by untrained or unauthorized personnel. The directives in the installation manual and operating manual for the Thermo Top series heater must be followed. Acknowledged engineering conventions must be observed for the installation work. All relevant state and provincial licensing regulations if any, governing the installation and use of auxiliary heating devices must be observed! CAUTION Location of heater, installation of coolant lines, fuel system and components, wiring and control devices are important for proper operation. Failure to comply with the installation instructions provided may result in poor operation or damage to heater and vehicle components. 3
4 BlueHeat TM Ford F-50/350 Super Duty Truck Symbol Identification Symbols that define sections in manual Mechanical Preparation Fuel Electrical Exhaust Coolant Combustion Air Intake General Symbol Descriptions Warning Refer to Webasto or Manufacturer Manual Caution Attention Flammable or Combustible Line of Sight/Item Location on Vehicle 4
5 Ford F-50/350 Super Duty Truck BlueHeat TM General References Bare body parts, for example, around drilled holes, must be treated with anti-corrosive coating. Secure hoses, cables and wiring harnesses with cable ties and fit protective hoses around them at chafing points. Fit edge protectors (opened fuel hose) to sharp edges. Preparation Heater Kit Verify and identify all contents of kit. Vehicle Verify fuel content in tank. CAUTION For reasons of safety due to the weight of fuel and the tank, it is recommended that there be no more than /4 tank of fuel present. If fuel quantity is greater than /4 of capacity, make provisions to reduce quantity of fuel or consider removal of pick-up box to gain access to fuel sender. Disconnect negative terminal of vehicle battery(s). Remove Air Cleaner Assembly Remove instrument panel cover for timer mounting. Refer to vehicle manufacturers instructions. Protect vehicle fenders, panels and interior with covers Heater Installation Site Mount the Webasto auxiliary heater under the right side of the cab, behind the front tire. () Webasto auxiliary coolant heater (Installed) () Right-front running board bracket Fig. 5
6 Ford F-50/350 Super Duty Truck Electrical - Overview If not described differently, secure wiring and cables with cable ties to the vehicle s own wires and cable harnesses. Timer control location is a recommendation only. Please consult with the customer before mounting. HVAC Blower Motor Fuel Metering Pump () Blower Motor () Right Framerail () Fuel Pump Fuse Block/Relays/Resistor Timer Control () Relays K & K () Digital Timer () Fuse Holder 6
7 Ford F-50/350 Super Duty Truck Fig. Electrical Harness Installation Modify electrical mounting bracket as shown in Figure. Cut wire tie holding negative-side blower harness (with relay) from main harness and set aside. Install resistor and relays on electrical mounting bracket. () Mounting bracket () Resistor (3) Screw M3x0, Nut M3 ( ea.) (4) Pan head screw 0-3x5/8, Nut 0-3 ( ea.) (5) Relays K and K Secure the electrical mounting bracket assembly to the bulkhead using a self-tapping screw. () Vehicle bulkhead - left corner () Electrical mounting bracket assembly Fig. 3 IMAGE NOT AVAILABLE CAUTION Use care when cutting bulkhead grommet to prevent damage to vehicle electrical harnesses. Cut a.7 mm (.5 inch) slit in the bulkhead pass-through grommet. Route the timer and blower control harnesses into the interior of the vehicle through the bulkhead grommet. Fig. 4 Fig. 5 Timer Installation CAUTION Check behind panels for obstructions before drilling holes. Before installing the timer, please confirm the installation location with the customer. Affix supplied template to panel. Drill 0 mm (5/64 in.) and.5 mm (3/3 in.) holes where indicated on template. Figure 5 shows a translated sample of the template supplied. 7
8 Ford F-50/350 Super Duty Truck () Timer - recommended location only Fuse Tap Connection - Relay K- CAUTION Tap into the fused output side of the selected fuse. Locate a fuse (0 to 0 amp) in the fuse / relay center that is HOT when the ignition is in the ON position only. Route blue fuse tap wire from relay K- to the fuse /relay center. () Underhood fuse / relay center () Fuse tap Fuse For 6.8 liter V 0 Fig. 6 Fig. 7 The underhood fuse / relay center cover has to be modified slightly to close properly after installing the fuse tap. Modify cover in locations circled in Figure 8. () Underhood fuse / relay cover Fig. 8 Integration into the Blower System Route Blower harness over to blower area. Mount negative-side blower harness and relay in vicinity of HVAC blower. Wire according to schematic in Figure 0. () Relay K3 () Blower motor connector (3) Blower power wire (4) Blower ground wire 3 4 Fig. 9 8
9 Ford F-50/350 Super Duty Truck Webasto 3 4 YL/GN YL/GN Vehicle 3-Relay HVAC Harness Connections NOTE: It is permissible to cut excess length from Webasto HVAC wiring harnesses to fit the application. Cut motor wires where indicated by X () Chassis ground () Splice green wire to green wire (3) Strip and crimp red to controller side power wire (4) Strip and crimp black to motor side power wire (5) Strip and crimp white to motor side ground wire (6) Strip and crimp blue to controller side ground wire 5 PL/PK PL/PK 6 Legend for Figure 0 A From Webasto Heater X B VDC Ignition On Fuse Tap C HVAC Control Module M HVAC Blower Motor X Cut wire at 50 mm ( in.) from motor F Fuse - Blower Circuit 5 Amp. K Relay - Ignition On Interrupt Fig. 0 CAUTION Check your wiring! Ensure that all connections have been done in accordance with the wiring diagram shown (Fig. 0). Sensitive electronic controls can be damaged if wired incorrectly! Secure HVAC blower control wiring to vehicle structures with nylon wire ties. (Image not available) NOTE: Complete heater harness schematics are included on page 7 and 8 of this manual. K Relay - Positive Side of Blower Motor K3 Relay - Negative Side of Blower Motor R Resistor - Blower Speed Control 30 Battery Positive (Constant Power) 5 Ignition (Switched Power) 3 Battery Negative (Chassis Ground) 9
10 Ford F-50/350 Super Duty Truck K3 Relay Ground Secure K3 Relay ground wire to a known good chassis ground. () K3 relay ground () A-pillar (right-side) Heater Control and Fuel Pump Harness Routing CAUTION Secure heater control and fuel pump harnesses away from hot exhaust components and moving vehicle components with cable ties. Route the heater control and fuel pump harnesses under the engine to the right side of the vehicle. () Heater control and fuel pump harnesses () Engine oil pan Fig. Fig. Secure the heater control and fuel pump harnesses to the engine cradle with cable ties. See Figure 3. () Engine oil pan () Engine cradle (3) Heater control and fuel pump harnesses 3 Fig. 3 Route the heater control and fuel pump harnesses over the right framerail where shown in Figure 4. () Heater control and fuel pump harnesses () Right framerail The remainder of the fuel pump harness will be routed later in this manual. Fig. 4 0
11 Ford F-50/350 Super Duty Truck Heater Preparation and Installation Observe torque specifications. Install heater mounting bracket on heater. () Heater mounting bracket () M6 EJOT screw (3 ea.) Torque 0 Nm (88.5 lb-in.) Fig. 5 Fig. 6 3 If the vehicle is not equipped with running boards, install panel nuts provided using the existing holes in the cab. Position the heater in it s mounting location. Align the holes in the rear of the mounting bracket with the panel nuts previously installed or existing hardware used to secure running boards and mark the front mounting hole location on the cab. Set heater aside and drill the front mounting hole. () Front mounting hole location (5/6 in. hole) () Cab body (behind front right wheel) (3) Panel Nuts Heater Mounting Use existing hardware to secure the heater if the vehicle is equipped with running boards (See Figure ). Connect heater harness to heater (not shown). Install heater on cab with hardware provided. () M8 bolt, washer, panel nut ( ea.) () Heater/mounting bracket assembly Fig. 7 Pull the inner fender splash shield back to install the front mounting hardware. Install the front mounting hardware. () Heater/mounting bracket () M8 bolt, washer, and flange nut Fig. 8
12 Ford F-50/350 Super Duty Truck Exhaust Installation Secure exhaust tube to heater with 90 exhaust elbow and two clamps. () Exhaust clamp ( ea.) () Exhaust tube (3) 90 exhaust elbow 3 Fig. 9 Ensure outlet end of exhaust tube is directed downward and slightly rearward 0 degrees. Secure the exhaust tube using existing holes in body and p-clamps provided. () Exhaust tube () P-clamp, M6 bolt, nut, and washer (3 ea.) Fig. 0
13 Ford F-50/350 Super Duty Truck Integration into the Coolant System Liter TT Diesel Torque hose clamps to Nm (8 - lb-in.) Avoid sharp bends and kinks when installing coolant hoses. Position hose clamps in such a way to avoid cutting or damaging adjacent components. Clamp vehicle coolant hose with hose clamping pliers prior to cutting to prevent coolant spillage. The coolant heater integration into the vehicle heater circuit is done in an INLINE fashion. Refer to Figure. Coolant flow and connection detail: Hose A: From engine to Webasto coolant pump inlet. Hose B: From Webasto heater outlet to vehicle heater core inlet. NOTE: Also see the plumbing schematic, page 9, of this manual for a general outline of the coolant circuit arrangement. Fig. 3
14 Ford F-50/350 Super Duty Truck Coolant Hose Connections Liter TT Diesel Cut supplied hoses as shown in Figure. Hose A: From engine to coolant pump inlet - Connect the 90 end to the coolant pump at the Webasto heater. Hose B: From Webasto heater outlet to vehicle heater core inlet - Connect the 90 end to the heater outlet. A Discard B Discard Fig. Install metal conduit on coolant hoses prior to installation. B Connect 90 end of hose A to Webasto heater coolant pump. Connect 90 end of hose B to Webasto heater outlet. 3 Route coolant hoses above the inner fender splash shield to the engine compartment. (A) Webasto heater inlet hose (B) Webasto heater outlet hose () Hose clamp - ea. () Coolant pump (3) Metal conduit A Fig. 3 Confirm supply and return hoses to vehicle heater core before cutting any coolant hoses. Once confirmed, cut supply hose, leaving sufficient hose for connections. Cut the heater core supply hose approximately 3 in. from the 90 bend in hose. Rotate supply hose toward the right side of the vehicle. See Figure 4. A Route the Webasto heater outlet hose B over to the heater core supply hose (90 section) and trim to proper length. Connect the Webasto heater outlet hose B to the heater core supply hose with coolant adapter and two hose clamps. Route the Webasto heater inlet hose A to heater core supply hose (engine side) and trim to proper length. Connect the Webasto heater inlet hose A to the heater core supply hose with coolant adapter and two hose clamps. B Fig. 4 () Heater core supply hose (A) Webasto heater inlet hose, adapter, and two clamps (B) Webasto heater outlet hose, adapter, and two clamps 4
15 Ford F-50/350 Super Duty Truck Integration into the Coolant System Liter V0 Gasoline Torque hose clamps to Nm (8 - lb-in.) Avoid sharp bends and kinks when installing coolant hoses. Position hose clamps in such a way to avoid cutting or damaging adjacent components. Clamp vehicle coolant hose with hose clamping pliers prior to removing to prevent coolant spillage. The coolant heater integration into the vehicle heater circuit is done in an INLINE fashion. Refer to Figure 5. Coolant flow and connection detail: Hose A: From engine to Webasto coolant pump inlet. Hose B: From Webasto heater outlet to vehicle heater core inlet. Hose C: Connects Hose B to heater core supply hose. Fig. 5 NOTE: Also see the plumbing schematic, page 9, of this manual for a general outline of the coolant circuit arrangement 5
16 Ford F-50/350 Super Duty Truck Coolant Hose Connections Liter V0 Gasoline Cut supplied hoses as shown in Figure 6. Hose A: From engine to coolant pump inlet - Connect the 90 end to the coolant pump at the Webasto heater. Hose B: From Webasto heater outlet to vehicle heater core inlet via hose C - Connect the 90 end to the heater outlet. Hose C: From Webasto heater outlet hose to the coolant hose removed from the engine coolant outlet tube. A Discard B Discard C Fig. 6 Prepare 80 coolant hose C for installation by installing coolant adapters as shown in Figure 7. (C) 80 coolant hose () Hose clamp - ea. () Coolant adapter - ea. C Fig. 7 Install metal conduit on coolant hoses prior to installation. B Connect 90 end of hose A to Webasto heater coolant pump. Connect 90 end of hose B to Webasto heater outlet. Route coolant hoses above the inner fender splash shield to the engine compartment. 3 (A) Webasto heater inlet hose (B) Webasto heater outlet hose () Hose clamp - ea. () Coolant pump (3) Metal conduit A Fig. 8 6
17 Ford F-50/350 Super Duty Truck 3 A B 4 3 Fig. 9 C Fig. 30 Clamp vehicle coolant hose with hose clamping pliers prior to removing hose from engine outlet. Route Webasto heater coolant inlet hose (hose going to heater water pump) to engine outlet tube and cut to appropriate length. Open constant tension clamp securing coolant hose to engine outlet tube and slide clamp back on hose. () Engine outlet coolant hose () Constant tension clamp (3) Engine outlet tube Pull vehicle coolant hose off engine outlet tube and install the Webasto heater inlet hose A with clamp. Route Webasto heater outlet hose B to the engine outlet tube and cut to the appropriate length. See Figure 30. Install the 80 coolant hose C between the webasto heater outlet hose B and the vehicle coolant hose removed from the engine outlet tube. (A) Webasto heater inlet hose (B) Webasto heater outlet hose (C) 80 Webasto heater hose () Hose clamp -ea. () Engine outlet tube (3) Constant tension clamp (4) Coolant hose from engine outlet tube Install plastic protective loom over coolant hose connections as shown in Figure 3. Secure coolant hoses with nylon cable tie. () Plastic protective loom () Nylon cable tie Fig. 3 7
18 Ford F-50/350 Super Duty Truck Combustion Air Intake Installation Observe torque specifications. Ensure air intake silencer is pointed downward when installed. The combustion air intake port is located directly above the coolant pump Install combustion air intake tube on heater. () Combustion air tube () #0 Clamp. Torque Nm (8 - lb-in.) Fig. 3 Install the air silencer on the combustion air intake tube. Route the combustion air intake tube up behind the inner fender splash shield and secure with cable ties. Bend the combustion air intake tube so that the silencer is pointing downward. Drill a /4 in hole through the splash shield near the air silencer. Secure the air silencer to the splash shield with the clamp provided. () Air intake silencer () Combustion air intake tube (3) Inner fender splash shield 3 Fig. 33 8
19 Ford F-50/350 Super Duty Truck Integration into the Fuel System Fuel Pump Installation The fuel pump is mounted horizontally along the right inside framerail using an existing hole in the frame. See Figure 34. () Fuel pump () P-clamp, M6 nut and bolt (3) Vehicle framerail (right) 3 Fig. 34 Ensure the fuel lines are fully seated within the fuel line couplers and any 90 degree bends are not buckled. Refer to Figure 35. Tighten all fuel line clamps to Nm ( lb.-in.) Fig. 35 Fuel Line Connection at Heater Cover fuel line with loom to protect it form sharp edges. Connect fuel line to heater with fuel line coupler and two clamps. () Mecanyl fuel line () Fuel line coupler (3) Fuel line clamp ( ea.) 3 Fig. 36 9
20 Ford F-50/350 Super Duty Truck Fuel Line and Fuel Pump Harness Routing CAUTION Secure fuel line and fuel pump harness away from moving vehicle components and hot exhaust. Route fuel line and fuel pump harness along right framerail towards the rear of the vehicle as shown in Figure 37. () Right framerail () Mecanyl fuel line (covered with plastic loom) and fuel pump harness (3) Front cab mount 3 Fig. 37 Route fuel line and fuel pump harness along right framerail towards the rear of the vehicle as shown in Figure 38. () Right framerail () Mecanyl fuel line (covered with plastic loom) and fuel pump harness Fuel Line Connection at Fuel Pump The outlet end of the fuel pump is quickly identified as the end with the electrical connector. Always cut Mecanyl fuel line with a sharp razor knife or razor edged cutter. DO NOT cut with side cutters, scissors or similar tools as doing so will cause a restriction inside the fuel line. Connect mecanyl fuel line to the outlet side of the fuel pump with fuel line coupler and two clamps. () Mecanyl fuel line () Fuel line clamp ( ea.) (3) Fuel pump electrical connector (4) Fuel line coupler Fuel Pump Harness Connection Install electrical connector on fuel pump harness per instructions found in electrical parts bag and connect to fuel pump. () Fuel pump harness () Fuel pump harness connector (3) Fuel pump Fig. 38 Fig. 39 Fig. 40 0
21 Ford F-50/350 Super Duty Truck Standpipe Installation Liter Diesel Remove fuel sending unit according to the vehicle manufacturers servicing instructions. De-burr both sides of hole after drilling. Drill a 8.5 mm (/64 in.) hole through the top of the fuel sender in the location shown. See Figure 4. () Fuel sending unit () 8.5 mm (/64 in.) hole Fig. 4 The standpipe tube should terminate approximately 38 mm (.5 in.) off the bottom of the fuel tank when installed. Remove any burrs from inside cut end of tube. Measure depth of fuel tank and cut standpipe to the appropriate length. () Standpipe or fuel pickup tube Fig. 4 3 Fig. 43 Ensure standpipe does not interfere with the float arm assembly. Install standpipe, see Figure 44 for item sequence. () Fuel sending unit () Standpipe (3) Float arm Legend for Figure 44 Banjo Bolt - Torque Nm (75-84 lb-in.) Banjo Fitting 3 Standpipe 4 Upper Sealing Washer (Black) 5 Fuel Tank 6 Lower Sealing Washer (Brass) 7 Lock Nut - Torque Nm (75-84 lb-in.) 7 Fig. 44
22 Ford F-50/350 Super Duty Truck Standpipe Installation Liter Gasoline Remove fuel sending unit according to the vehicle manufacturers servicing instructions. De-burr both sides of hole after drilling. Drill a 8.5 mm (/64 in.) hole through the top of the fuel sender in the location shown. See Figure 45. () Fuel sending unit () 8.5 mm (/64 in.) hole Fig. 45 The standpipe tube should terminate approximately 38 mm (.5 in.) off the bottom of the fuel tank when installed. Remove any burrs from inside cut end of tube. Measure depth of fuel tank and cut standpipe to the appropriate length. () Standpipe or fuel pickup tube Fig. 46 Ensure standpipe does not interfere with the float arm assembly. Install standpipe, see Figure 48 for item sequence. () Standpipe or fuel pickup tube () Fuel sending unit 3 Fig. 47 Legend for Figure 48 Banjo Bolt - Torque Nm (75-84 lb-in.) Banjo Fitting 3 Standpipe 4 Upper Sealing Washer (Black) 5 Fuel Tank 6 Lower Sealing Washer (Brass) 7 Lock Nut - Torque Nm (75-84 lb-in.) Fig. 48
23 Ford F-50/350 Super Duty Truck 6.4 Liter Diesel Fuel Line Connections and Routing Install fuel sender assembly according to the vehicle manufacturers servicing instructions. Connect fuel line to standpipe with fuel line coupler and two clamps. Refer to Figure 49 or 50. Secure fuel line to existing vehicle fuel lines and install fuel tank. 4 3 Fig. 49 () Fuel standpipe () Fuel line clamp ( ea.) (3) Fuel line coupler (4) Mecanyl fuel line 6.8 Liter Gasoline 3 4 Fig. 50 Route Mecanyl fuel line along existing vehicle fuel lines towards crossmember. See Figure 5. Secure fuel line with nylon cable ties. Fig. 5 CAUTION Secure fuel line away from moving vehicle components and hot exhaust. Route Mecanyl fuel line to the right side of the vehicle above the vehicle crossmember shown in Figure 5. Secure fuel line with cable ties. () Mecanyl fuel line exiting the crossmember at the right framerail () Vehicle crossmember Fig. 5 3
24 Ford F-50/350 Super Duty Truck Fuel Line Connection at Fuel Pump Always cut Mecanyl fuel line with a sharp razor knife or razor edged cutter. DO NOT cut with side cutters, scissors or similar tools as doing so will cause a restriction inside the fuel line. Cut fuel line to length and connect to the fuel pump with fuel line coupler and two clamps. () Fuel pump () Fuel line clamp ( ea.) (3) Fuel line coupler (4) Mecanyl fuel line (covered with loom) 3 4 Fig. 53 Power Connection The power wire has to be extended for vehicles equipped with the 6.8 Liter V0 Gasoline engine. Connect red power lead to battery positive terminal. () Webasto power lead () Battery positive terminal Fig. 54 Ground Connection The ground wire has to be extended for vehicles equipped with the 6.8 Liter V0 Gasoline engine. Connect brown ground lead to battery negative terminal. Reconnect battery ground cable. () Battery negative terminal () Webasto ground lead Fig. 55 4
25 Ford F-50/350 Super Duty Truck Final Inspection Initial Start-up and Concluding Work Final Inspection Inspect installation for: Loose fasteners. Exhaust system routing and clamp tightness. Combustion air intake tube routing and clamp tightness. Loose coolant line clamps. Pinched coolant lines. Routing of coolant lines and coolant lines securely tied and protected against chafing and related damage. Loose fuel line clamps. Routing of fuel lines and fuel lines securely tied and protected against chafing and related damage. Loose wiring connections and battery connections. routing of wiring harness and wiring harness securely tied and protected against chafing and related damage. Check operation of vehicle heater fan with Webasto heater OFF. Initial Start-up Top off cooling system with coolant per engine/vehicle manufacturers recommendations. Set interior heater control to maximum heat position (hot) and switch off air conditioning system. 3 Start the vehicle engine and run on fast idle for 5 minutes to purge any remaining air from the Webasto heater and coolant system. While the engine is running check: Hose connections for leaks. Coolant level in expansion tank. (Add coolant as needed) 4 Switch off the engine. More than one start-up attempt of the heater may be required to purge air from fuel system before heater will start. Cycle heater Off and On after each failed start attempt until heater starts successfully. After 3 consecutive unsuccessful start attempts, the webasto control unit enters into heater lockout. See Heater Lockout section for reset instructions. 5 Switch on the Webasto heater by means of the instant heat button on timer and check: Timer panel and instant heat indicator illuminates. Circulating pump in operation. Initiation of start-up sequence. Successful start-up and operation. 6 Allow heater to run for 0 minutes or until coolant is heated to temperature. Re-tighten all hose clamps. Engine coolant temperature gauge may read lower than actual Webasto heater output temperature. This is due to the location of the temperature gauge sensor on engine. Concluding Work Check that all hose lines, hose clamps, pipe clips and electrical connections are secure. Secure all loose lines and cables with nylon cable ties. Spray the heater components and electrical connections with an anti-corrosive wax coating. Install all vehicle parts, panels and components removed during heater installation. 5
26 Ford F-50/350 Super Duty Truck Heater Lockout Reset Procedure The BlueHeat is designed with a lockout safety feature built into the control unit. After 3 consecutive unsuccessful startup attempts, the heater will lock itself out from any further start attempts. The heater may also enter the lockout mode after experiencing an overheat condition. Reset Heater Lockout mode by performing the following procedure: Ensure timer or switch is in the OFF position. Turn timer or switch to the On position. Remove main fuse F (0 Amp), reinsert after 5 seconds. Cycle timer or switch off and then back on once more. Remove fuse F once again and reinsert after 5 seconds. Heater should attempt to start after inserting fuse. The engine coolant must be below 86 F (30 C) before the Webasto heater will attempt to start. Should the heater fail to start or operate correctly, contact your Webasto technical representative at:
27 Ford F-50/350 Super Duty Truck BlueHeat TM Electrical Harness Schematic - Part, Heater Control 7
28 BlueHeat TM Ford F-50/350 Super Duty Truck Electrical Harness Schematic - Part, HVAC Blower Control 8
29 Ford F-50/350 Super Duty Truck BlueHeat TM Heater Plumbing Schematic - Inline Method 9
30 BlueHeat TM Ford F-50/350 Super Duty Truck NOTES: 30
31 Ford F-50/350 Super Duty Truck BlueHeat TM Documentation Feedback Form Detailed user feedback is extremely valuable to us in producing accurate, comprehensive, and useful documentation. Please complete the relevant parts of the form below; your comments and suggestions will help us improve our documentation. Thank you. Unsatisfactory Excellent Please rate the overall usefulness of the documentation Rate the completeness and clarity of the instructions: did the procedures provide enough detail? What could be added or clarified? Please list any other comments, concerns, or suggestions. Please provided contact information below. Name: Company Name: City / State: Phone: Mail to: Webasto Product N. A., Inc North Road Fenton, MI Attention: Documentation Group or Fax to: (80)
32 Webasto Product N.A., Inc. Technical Assistance Hotline USA: (800) Canada: (800) Org. 0/007 Rev. 0/008 P/N B
BlueHeat Coolant Heater
BlueHeat Coolant Heater Thermo Top VW Jetta Beginning Model Year: 00 Special instructions for these models Part locations may differ slightly dependent on the vehicle model. Legend BlueHeat Coolant Heater,
More informationWater Heater Unit. Thermo Top C Additional Heater. Installation Instructions. FORD Connect. Gasoline and Diesel. not with automatic transmission
Water Heater Unit Thermo Top C Additional Heater e 00 000 Installation Instructions FORD Connect Gasoline and Diesel 4 5 6 not with automatic transmission only applies to left-hand drive vehicles See Page
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater e 00 000 e 00 000 Installation Instructions Alfa Romeo 47 Gasoline and Diesel from Model Year 00 Left-hand
More informatione ALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Thermo Top P Additional Heater e 00 004 Installation Instructions Toyota Land Cruiser J0 Diesel 4 5 6 from Model Year 005 For left-hand drive vehicles only Manual air conditioning not
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 000 e 00 004 Installation Instructions Dodge Nitro Diesel from Model Year 007 Left-hand drive vehicle
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater e 00 000 Installation Instructions Chevrolet Aveo Gasoline Notchback from Model Year 006 Hatchback from Model Year 008 Left-hand drive vehicle
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 000 e 00 000 e 00 004 Installation Instructions Toyota Hilux Diesel from
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top C Additional Heater e 00 000 Installation Instructions Chevrolet Captiva Diesel from Model Year 007 Left-hand drive vehicle Automatic transmission WARNING! Hazard
More informationALWAYS follow all Webasto installation and repair instructions and observe all warning instructions.
Water Heater unit Feel drive Supplementary heating Thermo Top C e 00 000 Installation instructions Dodge Caliber Diesel From model year 007 For left-hand drive vehicles only WARNING! Hazard warning: Incorrect
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 000 e 00 000 e 00 004 Installation Instructions Hyundai H.5 CRDi from
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 0003 e 00 000 e 00 004 Installation Instructions Mitsubishi Pajero Diesel
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater Thermo Top P Parking Heater e 00 0003 e 00 000 e 00 004 Installation documentation Nissan X-Trail Diesel from Model Year
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater Thermo Top P Parking Heater e 00 000 e 00 000 e 00 004 Installation documentation Mitsubishi Colt / Colt CZ / Colt CZC
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater e 00 000 e 00 000 Installation documentation Suzuki Splash Petrol from Model Year 008 Left-hand drive vehicle Manual
More informationWater heater unit. Installation instructions. Peugeot Partner. Citroen Berlingo. Supplementary heating Thermo Top C. Table of Contents.
Water heater unit Feel the drive Supplementary heating Thermo Top C e1 00 0002 Installation instructions Peugeot Partner Citroen Berlingo 6 4 1 2 3 5 Gasoline and diesel From model year 2003 Only for left-hand
More informationALWAYS follow all Webasto installation and repair instructions and observe all warning instructions.
Water heater unit Feel drive Thermo Top E Auxiliary Heating Thermo Top C Auxiliary Heating Thermo Top P Auxiliary Heating e 00 000 e 00 000 e 00 004 Installation instructions Toyota RAV 4 Petrol From model
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Thermo Top Evo Parking Heater e 00 058 Feel the drive Installation documentation Kia Sportage Diesel from Model Year 00 Left-hand drive vehicle Manual air conditioning Gear box AWD WARNING!
More informationRenault Laguna / - Grandtour / - GT / - Coupe
Water Heater Thermo Top E Parking Heater Thermo Top C Parking Heater E 00 000 E 00 000 Installation Documentation Renault Laguna / - Grandtour / - GT / - Coupe Diesel from model year 008 Left-hand drive
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater Thermo Top P Parking Heater e 00 0003 e 00 000 e 00 004 Installation documentation Mazda 6 Gasoline from Model Year 008
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top Evo Parking Heater e 00 058 Installation documentation Renault Koleos.0 Diesel from Model Year 009 Left-hand drive vehicle Automatic / manual air conditioning not
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater Thermo Top P Parking Heater e 00 000 e 00 000 e 00 004 Installation instructions Toyota Avensis Diesel from Model Year
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater e 00 0003 Installation Instructions Opel Meriva Diesel from Model Year 006 Left-hand drive vehicle WARNING! Hazard warning: Incorrect installation
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Thermo Top C Motorcaravan Parking Heater E 00 000 Installation Documentation Fiat Ducato 50 / Multijet Diesel From model year 006 Left-hand drive vehicle Manual / automatic air-conditioning
More informationCitroen C1 / Peugeot 107 / Toyota Aygo
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater e 00 000 e 00 000 Installation documentation Citroen C / Peugeot 07 / Toyota Aygo Petrol from Model Year 005 For left-hand
More informationD5W Z Auxiliary Heater Upgrade D5W Z Auxiliary Heater to Auxiliary Preheating System C
Water Heater DW Z Auxiliary Heater Upgrade DW Z Auxiliary Heater to Auxiliary Preheating System C 6 FORD Mondeo.0 l TDCI Diesel. l TDCI Diesel Legend for Figure Blade-type fuse holder and blower relay
More informationRenault Scenic / Grand Scenic / Megane
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 000 e 00 000 e 00 004 Installation Instructions Renault Scenic / Grand
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top Evo Parking Heater e 00 058 Installation documentation Dacia Duster / Sandero / Logan Petrol from model year 0 Left-hand drive vehicle Manual air conditioning WD
More informationCitroen Jumpy / Fiat Scudo / Peugeot Expert
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater e 00 000 e 00 000 Installation documentation Citroen Jumpy / Fiat Scudo / Peugeot Expert Diesel from Model Year 007 Left-hand
More informationINSTALLATION INSTRUCTIONS
2807 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY -6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater e 00 000 e 00 000 Installation Instructions Subaru Forester.0 Boxer Diesel from Model Year 009 Left-hand drive
More informationTOYOTA TUNDRA TVIP V4 Preparation
Preparation Part Number: PT398-00100 PT398-00100-AA Conflicts Do not install into vehicles without RKE system. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM
More informationC FORD F250 / F L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY
EXHAUST BRAKES C40019 1999-2003 FORD F250 / F350 7.3L POWERSTROKE DIESEL WITH AUTOMATIC TRANSMISSIONS ONLY Getting Started Thank you and congratulations on your purchase of a Pacbrake exhaust retarder.
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 000 e 00 000 e 00 004 Installation Instructions.4 TFSI from Model Year
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Thermo Top E Additional Heater Thermo Top C Additional Heater Thermo Top P Additional Heater e 00 000 e 00 000 e 00 00 Installation Instructions Hyundai Santa Fe. l CRDi
More informationWater heater unit. Thermo Top C Auxiliary Heating. for auxiliary heater C. Mazda 6 with standard Webasto Pre-heater. Diesel. 3 Pre-heater Z equipment
Water heater unit Thermo Top C Auxiliary Heating e 00 000 Pre-heater Z equipment for auxiliary heater C 7 6 5 Mazda 6 with standard Webasto Pre-heater Up to Model 0 with chassis No. 600 000 -door and 5-door
More informationINSTALLATION INSTRUCTIONS
28 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY 2-5 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Thermo Top Evo Parking Heater e 00 058 Feel the drive Installation documentation Kia Sportage Petrol from Model Year 00 Left-hand drive vehicle Manual / automatic air-conditioning system Gear
More informationRear Vision System Liftgate Emblem Camera for Aftermarket Display Ford Flex (Kit part number )
Rear Vision System Liftgate Emblem Camera for Aftermarket Display 2009-2012 Ford Flex (Kit part number 1008-6509) Kit Contents: Liftgate Emblem Mount with Camera Chassis Harness with RCA (Note: In some
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08E49-S2A-100 2004 S2000 AII 26325 Issue Date OCT 2003 PARTS LIST Hood switch harness TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Liftgate Emblem Camera Mirror Display 2009-2012 Ford Flex (Kit part number 1008-9527) Kit Contents: Mirror Liftgate Emblem Mount with Camera Interior (shorter) Harness Chassis (longer)
More informationInstallation and Commissioning of Auxiliary Power Unit
Models PC6012 PC6013 PC6014 PC6015 PC6022 PC6023 PC6024 Installation and Commissioning of Auxiliary Power Unit 30-871-21 Rev. E Warning & Cautions Vehicles with longer wheel bases should have the APU mounted
More informationThe use of Thermo Top P is not permitted for priority heating of the passenger compartment displayed in this coolant circuit in this EBA!
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater e 00 000 e 00 000 Installation documentation Kia Sorento. CRDI from Model Year 00 Left-hand drive vehicle Automatic air-conditioning
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Unit Feel the drive Upgrade Instructions Upgrading from auxiliary heater to additional heater with engine preheating Diesel from Model Year 006 WARNING! Hazard warning: Incorrect installation
More informationToyota 4RUNNER With/MR Overhead Video
Toyota 4RUNNER With/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit-00110-14, Beige 00016-00120; Fit Kit-00120-14, Gray Accessory Code: ED7 Conflicts: Vehicles without a sunroof Kit Contents:
More information650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Fullsize Ford 1992-Present Installing the Base Plate 1. Examine the interior and exterior
More information18SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines
8SP680Rev3 EPA04 MBE 4000 Car Hauler Low Pressure Fuel Lines KIT DESCRIPTION These service kits include all necessary parts to replace the low pressure fuel lines between the fuel filter housing and fuel
More informationINSTALLATION AND USER MANUAL
INSTALLATION AND USER MANUAL SDKIT-730 & SDKIT-734 100% Bolt-On 150 PSI Train Horn System for 2011-2015 F-250 & F-350 Super Duty P/N SDKIT-730 P/N SDKIT-734 Thank you for purchasing a Kleinn Air Horns
More informationLEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation
Preparation Part Number: PT944-24150 Kit Contents Item # Quantity Reqd. Description 1 2 Inner LED Scuff 2 2 Outer Scuff 3 1 Hardware Bag Hardware Bag Contents Item # Quantity Reqd. Description 1 15 20
More informationTOYOTA im INTERIOR LIGHT KIT Preparation
Preparation Part Number: PT922-12170 Kit Contents Item # Quantity Reqd. Description 1 1 Main Wire Harness 2 1 Switch 3 1 Switch Header 4 1 ECU 5 1 ECU Bracket 6 1 Hardware Kit 7 1 Instruction Card 8 1
More informationpart number:
part number: 0968 0908 part number: 0968 Water Heater Unit Feel the drive Thermo Top E dditional Heater Thermo Top C dditional Heater Thermo Top P dditional Heater e 00 000 e 00 000 e 00 004 Installation
More informationC40008 & C40009 EXHAUST BRAKES
EXHAUST BRAKES C40008 & C40009 1995 2003 Ford F250 / F350 7.3 L Powerstroke Diesel with manual transmissions 1995 1998 Ford F250 / F350 7.3 L Powerstroke Diesel with automatic transmission* *Requires the
More informationTOYOTA TUNDRA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: 08586-OC910 Conflicts Do not install into vehicles without RKE systems. Recommended Sequence of Application Item # Accessory 1 TVIP/RES Any TVIP or RES system 2 XM Radio NOTE:
More informationThermo 90 S.21 Diesel - 24 Volt
Coolant Heater Thermo 90 S.21 Diesel - 24 Volt Service Parts List for HMMWV (Humvee) 11/2012 P/N HMMWV Contents HMMWV - Thermo 90 S.21 Topic Heaters.........................................................................
More informationSHELBY GT500
2007-2009 SHELBY GT500 Removal of Factory Unit WARNING: 1. Radiator fluid must be handled properly. Please observe local ordinances with regards to handling and disposal. 2. Allow vehicle and components
More informationFAX
INSTALLATION INSTRUCTIONS 6090 Air Suspension Kit (pat. pending) 1999-2006 Tahoe, Suburban, Avalanche, Yukon Thank you for purchasing a quality Hellwig Product. PLEASE READ THIS INSTRUCTION SHEET COMPLETELY
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Aftermarket Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-6509) Kit Contents: Tailgate Emblem Mount with Camera Chassis Harness
More informationINSTALLATION INSTRUCTIONS
Rear Vision System Tailgate Emblem Camera Mirror Display 2009-Current Ford F-150 and 2010-Current Super Duty (Kit part number 1008-9527) Kit Contents: Mirror Tailgate Emblem Mount with Camera Interior
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top Evo Parking Heater e 00 058 Installation documentation Audi A6 / A6- Avant / Audi A7 Sportback.0 and.0 TDI quattro from model year 0 Left-hand drive vehicle Automatic
More informationTOYOTA YARIS HATCHBACK INTERIOR LIGHT UPGRADE Preparation
Preparation Part Number PTS21-52062-08 NOTE: Part number of this accessory may not be the same as the part number show Kit Contents Item # Quantity Reqd. Description 1 1 12 Light Guide 2 1 7 Light Guide
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater e 00 000 e 00 000 Installation instructions Subaru Legacy / Outback.0 and.5 Gasoline from Model Year 00 Left-hand drive
More informationROUSH Active IO Exhaust. Installation Instructions P/N: (R LITE) Fastback GT Convertible GT V8
Installation Instructions P/N: 422128 (R1318-5231LITE) Fastback GT Convertible GT V8 39555 Schoolcraft Rd, Plymouth MI, 48170 800.59.ROUSH ROUSH Active IO Exhaust Installation Instructions P/N: 422128
More informationTOYOTA COROLLA LED DRL eyebrow. Part Number: TCO-DRL
Part Number: TCO-DRL Kit Contents Item # Quantity Reqd. Description 1 2 DRL s bezels w/led DRL 2 1 Driver Box 3 1 Harness bag 4 1 User s card 5 1 Switch Hardware Bag Contents Item # Quantity Reqd. Description
More information650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present
TOMMY GATE OWNER'S / OPERATOR'S MANUAL 650 Series 650 LB Capacity 650 Series Cargo Van Lift Mounting Instructions Ford Transit (Standard Roof) 2015-Present Installing the Base Plate 1. Examine the interior
More informationMODEL NUMBER: MEDIUM DUTY ONBOARD AIR SYSTEM
MODEL NUMBER: 10003 MEDIUM DUTY ONBOARD AIR SYSTEM IMPORTANT: It is essential that you and any other operator of this product read and understand the contents of this manual before installing and using
More informationHP10098 BASIC INDEPENDENT AIR SPRING ACTIVATION KIT
HP10098 BASIC INDEPENDENT AIR SPRING ACTIVATION KIT Thank you and congratulations on the purchase of a Pacbrake basic independent air spring activation kit. Please read the entire installation manual prior
More informationMercedes Benz GLK 200 / 220 / 250 CDI (X204)
Water Heater Feel the drive Thermo Top Evo 5+ Parking Heater e 00 058 Installation documentation Mercedes Benz GLK 00 / 0 / 50 CDI (X04) Diesel from model year 009 Left-hand drive vehicle Automatic air-conditioning
More informationP Original Series Cargo Van Lift Mounting Instructions Fullsize Ford Van present. Preparing the Gate
Fullsize Ford Van- 1992-present Preparing the Gate 1. Remove the mounting hardware which is banded to the liftgate. 2. Verify mounting kit (Figure 1 and Table 1). S-400-40 STRAP VAN MOUNTING EAR BENT BRACKET
More informationKit INSTALLATION GUIDE. 5 psi Low Pressure Sensor (Single Gauge)
ª Kit 25592 5 psi Low Pressure Sensor (Single Gauge) MN-333 (131107) ECR 7119 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding with installation.
More informationConflicts: Vehicles with a sunroof
Toyota 4Runner Non/MR 2010-10.2 Overhead Video Part Number: 00016-00110; Fit Kit -00110-15, Beige 00016-00120; Fit Kit -00120-15, Gray Accessory Code: ED6 Conflicts: Vehicles with a sunroof Kit Contents:
More informationManufacturer Model Type EG-BE No./ ABE Skoda Octavia 1Z e11 * 2001 / 116 * 0230 *...
Water Heater Thermo Top Evo Parking Heater E 00 058 Installation Documentation Skoda Octavia Validity Manufacturer Model Type EG-BE No./ ABE Skoda Octavia Z e * 00 / 6 * 00 *... Motorisation Fuel Transmission
More informationManufacturer Model Type EG-BE No./ ABE Alfa Romeo Giulietta 940 e3 * 2007 / 46 * 0027 *...
Water Heater Thermo Top Evo Parking Heater E 00 058 Installation Documentation Alfa Romeo Giulietta Validity Manufacturer Model Type EG-BE No./ ABE Alfa Romeo Giulietta 940 e * 007 / 46 * 007 *... Motorisation
More informationSCION xa 2004 SATELLITE RADIO TUNER Section I Installation Preparation
Section I Installation Preparation Part Number: PT546 52040 Section I Installation Preparation Kit Contents Item # Quantity Reqd. Description 1 1 Satellite Tuner 2 1 Ground Cable 3 1 Tuner Cable 4 2 Tuner
More informationKit No Please read these instructions completely before proceeding with installation. Air Spring Kit Parts List. Bracket Attaching Hardware
Kit No. 59532 MN-572 (021108) ECR 7136 Please read these instructions completely before proceeding with installation Air Spring Kit Parts List A Item Description Quantity A Air Sleeves 2 B Upper Brackets
More informationPart Number: PT
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationSprinter Van A
I N S T A L L A T I O N G U I D E APPLICATION MODEL YR PART # Sprinter Van 2007-2016 75163-01A INSTALLATION TIME 3-5 Hours Professional installation recommended SKILL LEVEL 1 2 3 4 4= Experienced TOOLS
More informationTOYOTA SEQUOIA TVIP V4 REMOTE ENGINE STARTER (RES)
Preparation Part Number: PT398-34111 NOTE: Part number of this accessory may not be the same as the part number shown. Conflicts Do not install into vehicles without RKE system. Recommended Sequence of
More informationKit psi Low Pressure Sensor (Dual Gauge)
ª Kit 25812 5 psi Low Pressure Sensor (Dual Gauge) MN-337 (111107) ECR 7119 INSTALLATION GUIDE For maximum effectiveness and safety, please read these instructions completely before proceeding with installation.
More informationCAMRY STRIP LED DRL TOYOTA Part Number: Accessory Code: LDRS10. PIO / DIO Rev. A 02/26/13. Doc
Doc. 02.126.00 TOYOTA CAMRY PIO / DIO Rev. A 2013-02/26/13 STRIP LED DRL Part Number: 00016-32280 Accessory Code: LDRS10 Conflicts - Only works on Camry SE Kit Contents Item # Quantity Reqd. Description
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater Thermo Top P Parking Heater e 00 000 e 00 000 e 00 00 Installation documentation Citroen C Picasso Gasoline and Diesel
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater Thermo Top P Parking Heater e 00 000 e 00 000 e 00 00 Installation documentation Citroen C Picasso Gasoline from Model
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 30518 KIT 2006 PILOT Issue Date NOV 2005 NOTE: Accessory ATF and power steering coolers are required when installing the trailer hitch.
More informationALWAYS follow all Webasto installation and repair instructions and observe all warnings.
Water Heater Feel the drive Thermo Top E Parking Heater Thermo Top C Parking Heater e 00 000 e 00 000 Installation documentation Skoda Yeti Diesel - CR from model year 00 Left-hand drive vehicle Climatronic
More informationPRODUCT SAFETY NOTICE
PRODUCT SAFETY NOTICE Congratulations. This vehicle has been equipped with a Firestone air suspension system. This suspension will enhance the vehicle s handling when loaded, however, the vehicle s performance
More informationTOYOTA HIGHLANDER 2016 ON BOARD VACUUM CLEANER
2016 Part Numbers: 00016-48017- (01, 02, 04) Accessory Code: SV1000 NOTE: Will not work in Highlander HV Kit Contents Item # Quantity Reqd. Description 1 1 Vacuum Assembly 2 1 Hose Assembly 3 1 Tool Kit
More informationTOYOTA Yaris Hatchback EC REARVIEW MIRROR Preparation
Preparation Part Number: PT374-02090 Kit Contents Item # Quantity Reqd. Description 1 1 Auto Dimming Mirror Assembly w/ shift area light 2 1 Hardware bag Hardware Bag Contents Item # Quantity Reqd. Description
More informationOpel Astra / Astra Caravan / Astra GTC / Astra Twin Top
Water Heater Feel the drive Thermo Top C Parking Heater e 00 000 Installation documentation Opel stra / stra Caravan / stra GTC / stra Twin Top Petrol and Diesel from Model Year 004 Left-hand drive vehicle
More informationAssembly Instructions
Assembly Instructions Part Number Description Model Approx. Assembly Time 99994-0903 Windshield Wiper Kit Mule SX 1 Hour WARNING Improper installation of this accessory could result in an accident causing
More informationKIT CONTENTS. Multimeter or test light Wire crimpers or soldering equipment. Wire terminals & connectors 10A inline fuse
RUSSELL FORD 5.0L COMPLETE EFI PLUMBING KIT INSTALLATION INSTRUCTIONS Please study these instructions carefully before installing your new complete fuel system kit. If you have any questions, please call
More informationHP10134 & HP10135 KITS BASIC SIMULTANEOUS AIR SPRING ACTIVATION KIT
HP10134 & HP10135 KITS BASIC SIMULTANEOUS AIR SPRING ACTIVATION KIT Thank you and congratulations on the purchase of a Pacbrake simultaneous air spring activation kit. This kit was designed to add in-cab
More information69-74 VW Beetle IRS Rear Kit Part No
www.airliftcompany.com 69-74 VW Beetle IRS Rear Kit Part No. 75615 MN-476 (01102) ECN 3455 Please read these instructions completely before proceeding with installation A C B E D AA F F ITEM QTY. PART
More informationScion xa SATELLITE RADIO TUNER Preparation
Preparation Part Number: PTS31-00051 Kit Contents Item # Quantity Reqd. Description 1 1 Antenna, Interior 2 1 Antenna Tape Pad 3 1 Wire Harness 4 1 Bracket, Floor 5 3 Hardware Bags 6 3 Templates 7 1 SIRIUS
More informationINSTALLATION INSTRUCTIONS
INSTALLATION INSTRUCTIONS Accessory Application Publications No. AII 25877 PILOT Issue Date AUG 2003 Optional ATF and power steering coolers are required when installing the trailer hitch. 2 Spacers PARTS
More informationManufacturer Model Type EG-BE No. / ABE Peugeot 3008 OU e1 * 2001 / 116 * 0377 *... Peugeot 5008 O e2 * 2007 / 46 * 0004 *...
Water Heater Thermo Top Evo Parking Heater E 00 058 Installation Documentation Peugeot 008 / 5008 Validity Manufacturer Model Type EG-BE No. / ABE Peugeot 008 OU e * 00 / 6 * 077 *... Peugeot 5008 O e
More informationINSTALLATION INSTRUCTIONS
2806 INSTALLATION INSTRUCTIONS SECTION - AIR SPRING SECTION 2 - AIR ACCESSORY -6 ! IMPORTANT PLEASE DON T HURT YOURSELF, YOUR KIT OR YOUR VEHICLE. TAKE A MINUTE TO READ THIS IMPORTANT INFORMATION. This
More informationTITAN Fuel Tanks. INSTALLATION INSTRUCTIONS G e n e r a t i o n V. Extended Capacity Replacement Tank for Diesel Chevrolet / GMC Trucks
Important: Please read these instructions carefully and completely before starting the installation. TITAN Fuel Tanks INSTALLATION INSTRUCTIONS G e n e r a t i o n V Extended Capacity Replacement Tank
More informationManufacturer Model Type EG-BE No./ ABE Alfa Romeo Giulietta 940 e3 * 2007 / 46 * 0027 *...
Water Heater Thermo Top Evo Parking Heater E 00 058 Installation Documentation Alfa Romeo Giulietta Validity Manufacturer Model Type EG-BE No./ ABE Alfa Romeo Giulietta 940 e * 007 / 46 * 007 *... Motorisation
More informationBEFORE BEGINNING INSTALLATION
COMPLETE CHASSIS FUEL LINE KITS For 1996-2000 Honda Civic Equipped with B-Series Engine INSTALLATION INSTRUCTIONS PLEASE study these instructions carefully before beginning this installation. Most installations
More informationWater Heater. Installation Documentation Renault Scenic / Grand Scenic / Megane. Thermo Top Evo Parking Heater. Validity
Water Heater Thermo Top Evo Parking Heater E 00 058 Installation Documentation Renault Scenic / Grand Scenic / Megane Validity Manufacturer Model Type EG-BE No./ ABE Renault Scenic JZ e * 00 / 6 * 079
More informationManufacturer Model Type EG-BE No./ ABE Fiat Doblo 263 e3 * 2007 / 46 * 0007 *... Fiat Doblo Cargo 263 e3 * 2007 / 46 * 0002 *...
Water Heater Thermo Top Evo Parking Heater E 00 058 Installation Documentation Fiat Doblo / Doblo Cargo Validity Manufacturer Model Type EG-BE No./ ABE Fiat Doblo 63 e3 * 007 / 46 * 0007 *... Fiat Doblo
More informationTOYOTA HIGHLANDER w/smart Key TVIP V4 REMOTE ENGINE STARTER (RES) Part Number: PT
Preparation Part Number: PT398-48083 Conflicts Do not install into vehicles without RKE systems. Will not program with Techstream Lite. Recommended Sequence of Application Item # Accessory Kit Contents
More information