SUMMARY STEPS TO CERTIFY FAN PERFORMANCE UNDER AMCA INTERNATIONAL S CERTIFIED RATINGS PROGRAM

Transcription

1 AMCA International Member Logo cannot be used in catalogs containing performance data. AMCA International Corporate Identity Logo can only be used by AMCA International, Inc. SUMMARY STEPS TO CERTIFY FAN PERFORMANCE UNDER AMCA INTERNATIONAL S CERTIFIED RATINGS PROGRAM AMCA Seal can only be used in conjunction with AMCA Licensed Products. This is a summary only. The Certified Ratings Program is fully described in AMCA Publications, and. Please read these Publications, particularly the Product Rating Requirement Subsections of Publication. STEP APPLY TO BECOME AN AMCA INTERNATIONAL MEMBER OR CRP AFFILIATE (APPLICANT'S RESPONSIBILITY) Newcomers to AMCA International s Certified Ratings Program must first decide whether they would like to become an AMCA International Member or a CRP Affiliate. Although it is usually less costly to participate in the Certified Ratings Program as a Member, it is not necessary to become an AMCA International Member in order to participate in the Certified Ratings Program. Membership is limited to any business engaged in the design, fabrication, assembly and sale of devices within the product scope of AMCA International. Information on membership can be obtained by submitting a request to AMCA International s Executive Director, or by completing the Membership Interest Form located at on AMCA International's website. If you are not eligible to become an AMCA International Member, or if you do not wish to become an AMCA International Member, you must complete an application to become an AMCA International CRP Affiliate. Applications are available from AMCA International upon request.

2 STEP SIGN LICENSE AGREEMENT Publication, Section. (APPLICANT'S RESPONSIBILITY) License Agreements are signed only once, prior to the first product being certified. Upon approval of the application, AMCA International will mail two License Agreements to the Licensee Representative. Sign, witness and seal both copies and return them to AMCA International. AMCA International will then sign, witness and seal both copies and return one copy to you along with the License Appendix for your first product line after Step is completed. A product is certified only after a License Appendix has been issued by AMCA International. Each certified product will have a unique License Appendix Number. STEP TESTING Publication, Section. (APPLICANT'S RESPONSIBILITY) The fans may be tested in AMCA International s Laboratory, an independent laboratory licensed to perform tests for AMCA International, or in an AMCA International Accredited Laboratory. Contact AMCA International s Director of Laboratory Services to arrange for testing in AMCA International s Laboratory, or for information on AMCA International s Laboratory Accreditation Program. Not every size of a product line needs to be tested. If there is a geometric proportionality between several sizes, you may calculate the performance of the larger sizes from a smaller size using the Fan Laws. Although the Licensee is responsible for selecting test sizes, the AMCA International technical staff will assist in selection of test sizes. STEP APPLY FOR LICENSE AGREEMENT APPENDIX Publication, Section. and. (APPLICANT'S RESPONSIBILITY) SUBMIT TO AMCA INTERNATIONAL: A. Completed CRP- Forms signed by the Licensee Representative. Please visit to download a form. Please submit a separate CRP- form for each product line. B. Test data in conformance with the test standard used. These results must be corrected to standard air density. C. Performance curves of the test results with the test points identified. D. Photographs of each test setup. E. Dimensional drawings giving the dimensions listed in AMCA Publication, Annex A. Marked photocopies of the appropriate drawings from Annex A are acceptable, or contact AMCA International for a PDF version. F. Reverberant room qualification data for fans being certified for sound. For sound only not necessary of sound tests conducted in AMCA International s Laboratory.

3 STEP STAFF REVIEW OF SUBMITTAL DATA Publication, Section. (AMCA INTERNATIONAL'S RESPONSIBILITY) AMCA INTERNATIONAL STAFF WILL CHECK THAT: A. The completed CRP- form is signed by the Licensee Representative. B. Every test listed on the CRP- form is contained in the submittal and in conformance with the standard used. C. Performance curves are included with the test results. D. Photographs of the test(s) are included. E. Drawings and dimensions are in conformance with AMCA Publication, Annex A and Subsection A.. If the submittal is in conformance, the AMCA International staff will select a Precertification Test Unit and a Precertification Check Test Request to the Licensee Representative. A Precertification Test is not necessary if all tests were run in AMCA International s Laboratory or an independent laboratory licensed to perform tests for AMCA International. If the submittal is not in conformance, the AMCA International staff will notify the applicant by of the items required to complete the application. STEP PRECERTIFICATION CHECK TEST Publication, Section. (APPLICANT'S RESPONSIBILITY) (Required if the tests were conducted in an AMCA International Accredited Laboratory) A. Complete the Application and Agreement for Testing Service Form (TAF) using My AMCA (unless otherwise instructed) and ship (prepaid) the Precertification Check Test Unit to AMCA International. The Test Application Number should be marked on the outside of the test unit and its crate. (AMCA INTERNATIONAL'S RESPONSIBILITY) B. Tests are scheduled after both the TAF and unit are received. AMCA International will run the tests and notify the applicant of the results. If the test is unsatisfactory, AMCA International will select an additional Precertification Check Test Unit. STEP SUBMIT PROPOSED CATALOG DATA Publication, Section. (APPLICANT'S RESPONSIBILITY) The data may also be submitted with the CRP- form in Step above, or as part of the catalog proof copy in Step below. STEP AMCA INTERNATIONAL REVIEW OF PROPOSED CATALOG DATA Publication, Section. and.0 (AMCA INTERNATIONAL'S RESPONSIBILITY) The AMCA International staff will review the proposed catalog data. If the proposed data is not satisfactory, staff will notify the applicant by . If the proposed catalog data has been verified as correct by AMCA International staff, a Notice of Acceptability will be sent by .

4 STEP SUBMIT CATALOG PROOF COPY Publication, Section. (APPLICANT'S RESPONSIBILITY) Submit a proof copy of the catalog and/or electronic media to AMCA International staff for verification of the performance data and conformance to the requirements of the Certified Ratings Program. AMCA International will retain the proof copy of the catalog. Electronic versions of the AMCA International Seal are available from AMCA International for use in catalogs. STEP 0 AMCA INTERNATIONAL REVIEW OF PROOF COPY Publication, Section. (AMCA INTERNATIONAL'S RESPONSIBILITY) The AMCA International staff will review the proof copy and notify the applicant by of any necessary corrections or of the proof copy s acceptability. STEP SUBMIT PRINTED CATALOG Publication, Section. (APPLICANT'S RESPONSIBILITY) Submit one copy of the printed catalog and/or electronic media to the AMCA International staff immediately prior to being released to the public. STEP AMCA INTERNATIONAL REVIEW OF PUBLISHED CATALOG AND ISSUANCE OF LICENSES Publication, Section. (AMCA INTERNATIONAL'S RESPONSIBILITY) The AMCA International staff will review the printed catalog and, if it is unchanged from the proof copy shall issue an Appendix to the License Agreement for the product line. In the event that the catalog does not meet the requirements of the program, the applicant shall be notified immediately by of the discrepancy, advised not to distribute the catalog to the public and a License Appendix shall not be issued. The applicant must then correct the discrepancy and resubmit the catalog to the AMCA International staff for review and approval. Note: This post-printing action will only happen if changes are made to the AMCA International approved proof copy. MANUFACTURING/PRODUCTION CHECK Publication, Section. If the base tests are conducted on a prototype, AMCA International will request a Check Test within one year after the License Appendix is issued. If the base tests are conducted on a production model, the Check Test will be requested within three years after the License Appendix is issued.

5 CHECK LIST Company Model Step Apply to Become an AMCA International Member or CRP Affiliate Step Sign License Agreement Step Testing Step Apply for License Agreement Appendix Step Staff Review of Submittal Data Step Precertification Check Test Step Submit Proposed Catalog Data Step AMCA International Review of Proposed Catalog Data Step Submit Catalog Proof Copy Step 0 AMCA International Review of Proof Copy Step Submit Printed Catalog Step AMCA International Review of Published Catalog and Issuance of Licenses Revised //0

6 AMCA Publication Proportionality W A Diameter at Blade Tip B W Diameter at Blade Heel Blade Width at Discharge D B A D Minimum Diameter at Inlet Cone N Number of Blades Figure A- Backward inclined centrifugal impeller Model No./Size A B W D N 0

7 AMCA Publication Proportionality W A B W D N Diameter at Blade Tip Diameter at Blade Heel Blade Width at Discharge Minimum Diameter at Inlet Number of Blades D B A Figure A- Forward curved centrifugal impeller Model No./Size A B W D N 0

8 AMCA Publication Proportionality W A B W D N Diameter at Blade Tip Diameter at Blade Heel Blade Width at Discharge Inlet Diameter Number of Blades D B A Figure A- Radial centrifugal impeller Model No./Size A B W D N 0

9 AMCA Publication Proportionality W A Major Diameter at Discharge A Minor Diameter at Discharge B Major Diameter at Blade Heel W Blade Width at Discharge D Minimum Diameter at Inlet Cone N Number of Blades D B A A Figure A- Mixed flow impeller Model No./Size A A B W D N 0

10 AMCA Publication Proportionality A H G " N Diameter at Blade Tip Hub Diameter Blade Width at Discharge Pitch Angle at Tip or at a Designated Radius Number of Blades A H " G Figure A- Vaneaxial propeller Model No./Size A H G α N 0

11 AMCA Publication Proportionality A Diameter at Blade Tip H Hub Diameter G Blade Width at Tip " Pitch Angle at Tip or at a Designated Radius N Number of Blades A H " G Figure A- Tubeaxial propeller Model No./Size A H G α N 0

12 AMCA Publication Proportionality A Diameter H Blade Root Diameter, May be 0% less than Catalogued G Blade Width at a Designated Radius " Pitch Angle at a Designated Radius N Number of Blades A H G " Figure A- Fabricated propeller Model No./Size A H G α N 0

13 AMCA Publication Proportionality Tip Clearance Design tip clearance is defined as the difference between the design radius of the impeller and the design internal radius of the fan casing. Measured tip clearance is defined as the average of the tip clearance measurement for all blades taken at eight locations o ( intervals) around the fan casing. Inside Surface of Casing Figure A- Tip clearance Model No./Size Tip Clearance 0

14 AMCA Publication Proportionality A or A A B C Width of Discharge (or Evase, as applicable) Height of Discharge (or Evase, as applicable) Point of Inlet Radius or Inlet Collar Diameter C B or B Figure A- Centrifugal fan housing SI-DI Model No./Size A B C 0

15 AMCA Publication Proportionality S A B L Shaft Diameter if Shaft Extends Through Box Inlet Height Inlet Width Inlet Box Length A B L S Figure A-0 Inlet box Model No./Size S A B L 0

16 AMCA Publication Proportionality Q C Shaft Height above Base Inlet Diameter at Tangent Point of Inlet Radius or Inlet Collar Diameter Q C Figure A- ARR. plenum fan Model No./Size Q C 0

17 AMCA Publication Proportionality Q C Shaft Height above Base Inlet Diameter at Tangent Point of Inlet Radius or Inlet Collar Diameter Q C Figure A- ARR. plenum fan Model No./Size Q C 0

18 AMCA Publication Proportionality P C Panel Size Inlet Diameter at Tangent Point of Inlet Radius or Inlet Collar Diameter P C Figure A- Plug fan Model No./Size P C 0

19 AMCA Publication Proportionality U B B T J E NV Drum Diameter or Square Size Interior Drum Size Interior Drum Size at Discharge Length to Belt Tube Belt Tube Size Length of Vanes Number of Vanes U T E J B B NV Figure A- In-line centrifugal fan Model No./Size U B B T J E NV 0

20 AMCA Publication Proportionality U B T E NV J Diameter - ID Interior Drum Diameter Length to Belt Tube Length of Vanes Number of Vanes Belt Tube Size U T E J B NV Figure A- Vaneaxial fan belt drive Model No./Size U B T E NV J 0

21 AMCA Publication Proportionality E U B E NV Diameter - ID Inside Diameter of Vanes Length of Vanes Number of Vanes U B NV Figure A- Vaneaxial fan direct drive Model No./Size U B E NV 0

22 AMCA Publication Proportionality T J U B T J Diameter - ID Size of Drive Tube Length to Belt Tube Belt Tube Size U B Figure A- Tubeaxial fan belt drive Model No./Size U B T J 0

23 AMCA Publication Proportionality U Diameter U Figure A- Tubeaxial fan direct drive Model No./Size U 0

24 AMCA Publication Proportionality K O K R P Orifice Diameter Orifice Depth Orifice Radius Panel or Ring Size P O R Figure A- Propeller fan Model No./Size O K R P 0

25 AMCA Publication Proportionality V N V F C I M Hood Height Hood Diameter or Size Discharge Area or Size Inlet Collar Size (if provided) Recommended Inside Curb Dim. Minimum Height Above Roof M C I F N Figure A-0 Centrifugal PRV exhaust-down discharge Model No./Size N V F C I M 0

26 AMCA Publication Proportionality V F C I Housing Diameter or Size Discharge Area or Size Inlet Collar Size (If Provided) Recommended Inside Curb Dim. V F C I Figure A- Centrifugal PRV exhaust-up discharge Model No./Size V F C I 0

27 AMCA Publication Proportionality V O V F C K M I R Orifice Diameter Hood Diameter or Size Discharge Size or Area Inlet Collar Size (If Provided) Orifice Depth Minimum Height Above Roof Recommended Inside Curb Dim. Orifice Radius M R O C I K F Figure A- Axial PRV supply or exhaust Model No./Size O V F C K M I R 0

28 AMCA Publication Proportionality V V Hood Size F Intake Size or Area N Hood Height Y Body Size M Height Above Base See A for Blower Required N M F Y Figure A- Centrifugal supply PRV Model No./Size V F N Y M 0

29 AMCA Publication Proportionality X X C O K R I Windband Diameter Inlet Collar Size (If Provided) Orifice Diameter Orifice Depth Orifice Radius Recommended Inside Curb Dim. R O K C I Figure A. Axial upblast PRV Model No./Size X C O K R I 0

30 AMCA Publication Proportionality X C X I Inlet Collar Size (If Provided) Windband Diameter, Inside Recommended Inside Curb Dim. See Tubeaxial and Vaneaxial for Dim. Figures A- to A- C I Figure A- Axial upblast PRV Model No./Size C X I 0

31 AMCA Publication Proportionality V C V F N M I Inlet Collar Size (If Provided) Hood Size Discharge/Intake Size or Area Hood Height Height Above Roof Recommended Inside Curb Dim. F N See tubeaxial Figure A- and A- for Required Fan Dim. M C I Figure A- Axial supply/exhaust PRV Model No./Size C V F N M I 0

32 AMCA Publication Proportionality V V F N M Y O K R Hood Size Discharge/Intake Size of Area Hood Height Height Above Roof Body Size Orifice Diameter Orifice Depth Orifice Radius N M O F R Y Figure A- Combination PRV exhaust-supply-circulate Model No./Size V F N M Y O K R 0

33 AMCA Publication Proportionality X Y Body Size K Orifice Depth O Orifice Depth R X Orifice Radius Wind Band Diameter, Inside K R O Y Figure A- Combination PRV exhaust-circulate Model No./Size Y K O R X 0

34 AMCA Publication Proportionality See Figure A- for Dimensional Requirements for Propeller Fans Provide All Required to Define Inlet and/or Outlet Appurtenances Figure A- Agricultural fans Model No./Size 0

35 AMCA Publication Proportionality L Z Z B A Y L Z Interior Width Fan Spacing A B Y Interior Height Interior Depth Shaft Center Height See Tubeaxial and Vaneaxial Figures A- to A- for Required Fan Figure A-0 Vane/tubeaxial air curtain Model No./Size L Z A B Y 0

36 AMCA Publication Proportionality L Z Z Z B X A Y V W A B L V Interior Height Interior Depth Interior Width Motor Spacing (where applicable) W X Y Z Centrifugal Fan/Housing Width Shaft Center Depth Shaft Center Heigfht Centrifugal Fan/Housing Spacing Figure A- Centrifugal/tangential air curtain Model No./Size A B L V W X Y Z 0

37 AMCA Publication Proportionality L Z Z K B O A R Y W A Interior Height B Interior Depth L Interior Width K Orifice Depth Z Axial Fan Spacing R Orifice Radius W Impeller Diameter at blade Tip O Min. Diameter of Inlet Cone Y Shaft Center height Figure A- Axial air curtain Model No./Size L Z W A B K R O Y 0

38 AMCA Publication Proportionality K W O K O W Inlet Orifice Depth Minimum Diameter of Inlet Orifice Tip Clearance Figure A- Circulator fan Model No./Size K O W 0

39 AMCA Publication Proportionality T N T S N N N T T S Number of Rings Number of Radial Supports Ring Thickness Radial Support Thickness Ring Spacing Figure A- Circulator fan head with guard Model No./Size N N T T S 0

40 AMCA Publication Proportionality Li L Lo Di Dfi D Dfo Do Ri N Ro L Li Lo D Di Do Dfi Dfo Ri Ro N Fan Length Inlet Silencer Lenght Outlet Silencer Length Fan Diameter Inlet Silencer Diameter Outlet Silencer Diameter Inlet Fairing Diameter Outlet Fairing Diameter Inlet Bell Radius Outlet Bell Radius Number of Vanes Figure A- Jet tunnel fan dimensions Model No./Size L Li Lo D Di Do Dfi Dfo Ri Ro N

41 AMCA Publication Proportionality Figure A- Induced Flow Fan Nozzle and Windband Model No./Size A B C D E F G

42 CHECKLIST: AIR PERFORMANCE CATALOGS CATALOG IDENTIFICATION DATE OF CATALOG I. SEAL USAGE IN CATALOGS A. Pick the correct AMCA Seal: [check all that apply] Air Performance Sound and Air Performance CFM/Watt Air Performance Positive Pressure Ventilator Air Performance Efficiency Air Performance Efficiency Sound and Air Performance Induced Flow Fan Air Performance Induced Flow Fan Air and Sound Performance Smoke Management Fan Performance Smoke Management Fan Performance Reversible Operation B. Placement of AMCA Seal: [check all that apply]. If the catalog contains all licensed products, the seal and qualifying statement shall be prominently displayed either on the cover or in the catalog.. If the catalog contains both licensed and unlicensed products, the AMCA Seal and qualifying statement shall not be shown on the outside cover.. In addition, the AMCA Seal may be shown on any page with licensed performance data. C. Reproduction of AMCA Seal in Catalogs. Size: No reproduction of the AMCA International Certified Ratings Seal in published material shall be larger than mm x 0 mm ( / in. x / in.), unless the AMCA International staff gives specific permission.. Color: When using one color reproduction, black is preferred. If light colored paper is used, regard it as white for this purpose. The full color AMCA Seal may be used. The CRP Manager will reproductions of the AMCA Seal for use in the catalog upon request. D. Member Logo Other than the AMCA International Certified Ratings Seal, no logo or mark incorporating the acronym AMCA International or initials A.M.C.A. such as the member logo shall be reproduced in any catalog or publication containing performance ratings of any kind. Rev. /0

43 II. QUALIFYING STATEMENT ADJACENT TO THE SEAL In catalogs containing ratings of licensed products, the following statement shall be printed prominently and immediately adjacent to the reproduction of the AMCA Certified Ratings Seal as required by I.B: "(Licensee's name as shown on License Agreement) certifies that the (product description) shown herein is (or are) licensed to bear the AMCA Seal. The ratings shown are based on tests and procedures performed in accordance with AMCA Publication (and AMCA Publication if sound is also certified) and comply with the requirements of the AMCA Certified Ratings Program." III. CATALOG IDENTIFICATION REQUIREMENTS Catalogs containing performance ratings of licensed products shall be provided with a catalog identification reference, and the month and year of publication shall be spelled out, e.g. "November 00," on the outside front or outside back cover of the product catalog. The catalog identification may be any combination of letters and/or numbers. Where ratings are on separate sheets or on loose leaf that may be removed from the cover, each sheet or loose leaf shall be identified and dated as above. The final printed catalog shall have a current date. IV. EFFICIENCY The following statement shall be shown immediately adjacent to the efficiency ratings: Efficiency ratings are fan static (or fan total) and include (or exclude) bearing and/or Power Transmission Losses. V. REQUIREMENTS FOR AIR PERFORMANCE Rating Method (see last page of Publication to determine rating method) [check one] A B C D E F G H I J K L Determine the rating method and then check the appropriate statements to be used. The statements shall be shown immediately adjacent to the rating tables, graphs or charts. A. Rating Method "A" (Constant Speed, Transmission Loss Not Included) The performance ratings for each model number shall include: Airflow rate Static pressure and/or total pressure Fan input power Rev. /0

44 Impeller speed Inlet air density (if other than standard air) Fan static and/or fan total efficiency (optional) Required Statements:. Power rating (watts, kw or BHP) does not include transmission losses. A. Performance ratings do not include the effects of appurtenances (accessories). or B. Performance ratings include the effects of [list appurtenances here]. B. Rating Method "B" (Constant Speed, Transmission Losses Included) The performance ratings for each model number shall include: Airflow rate Static pressure and/or total pressure Fan input power Impeller speed Inlet air density (if other than standard air) Fan static and/or fan total efficiency (optional) Required Statements:. Power rating (watts, kw or BHP) includes transmission losses. A. Performance ratings do not include the effects of appurtenances (accessories). or B. Performance ratings include the effects of [list appurtenances here]. Rev. /0

45 C. Rating Method "C" (As Run Speed, Transmission Losses Included, Low Slip Motor) The performance ratings for each model number shall include: Airflow rate Static pressure and/or total pressure Maximum fan input power over the range catalogued, or fan input power at the stated duty Actual impeller speed at each point of ratings or a nominal speed Inlet air density (if other than standard air) Fan static and/or fan total efficiency (optional) Required Statements:. Power rating (watts, kw or BHP) includes transmission losses.. Speed (RPM or RPS) shown is nominal. Performance is based on actual speed of test. Use this statement only when nominal speed is catalogued. A. Performance ratings do not include the effects of appurtenances (accessories). or B. Performance ratings include the effects of [list appurtenances here]. D. Rating Method "D" (Direct Drive, Constant Speed, Low Slip Motor) The performance ratings for each model number shall include: Airflow rate Static pressure and/or total pressure Maximum fan input power over the range catalogued, or fan input power at the stated duty, or maximum motor input watts, voltage and frequency over the range catalogued, or motor input watts, voltage, and frequency at the state duty Impeller speed Inlet air density (if other than standard air) Fan static and/or fan total efficiency (optional) Rev. /0

46 Required Statements: A. Performance ratings do not include the effects of appurtenances (accessories). or B. Performance ratings include the effects of [list appurtenances here]. E. Rating Method "E" (Direct Drive, As Run Speed, Low Slip Motor) The performance ratings for each model number shall include: Airflow rate Static pressure and/or total pressure Maximum fan input power over the range catalogued, or fan input power at the stated duty, or maximum motor input watts, voltage and frequency over the range catalogued, or motor input watts, voltage, and frequency at the stated duty Actual impeller speed at each point of rating or a nominal speed Inlet air density (if other than standard air) Fan static and/or fan total efficiency (optional) Required Statements:. Speed (RPM or RPS) shown is nominal. Performance is based on actual speed of test. Use this statement only when nominal speed is catalogued. A. Performance ratings do not include the effects of appurtenances (accessories). or B. Performance ratings include the effects of [list appurtenances here]. F. Rating Method "F" (Direct Drive, As Run Speed, High Slip Motor) The performance ratings for each model number shall include: Airflow rate Static pressure Maximum motor input watts, voltage and frequency over the range catalogued, or motor input watts, voltage, and frequency at the stated duty (optional if less than 00 watts) Rev. /0

47 Actual impeller speed at each point of rating or nominal speed Inlet air density (if other than standard air) Fan static and/or fan total efficiency (optional) Required Statements:. Speed (RPM or RPS) shown is nominal. Performance is based on actual speed of test. Use this statement only when nominal speed is catalogued. A. Performance ratings do not include the effects of appurtenances (accessories). or B. Performance ratings include the effects of [list appurtenances here]. G. Rating Method "G" (Air Curtains) The performance ratings for each model number shall include: Airflow rate Average outlet velocity Motor input power, voltage, and frequency Outlet velocity uniformity Inlet air density (if other than standard air) Fan static and/or fan total efficiency (optional) Required Statements:. The AMCA Certified Ratings Seal applies to airflow rate, average outlet velocity, outlet velocity uniformity, velocity projection and power rating at free delivery only.. Rated data shown are only for base (unheated) units, as shown.. Performance data obtained from the correction factors shown herein are only an approximation and shall not be considered as part of the AMCA Certified Ratings. Rev. /0

48 H. Rating Method "H" (Direct Drive, Jet Tunnel Fan, As Run Speed) The performance ratings for each model number shall include: Airflow rate Nominal impeller speed Thrust (N or Ib f ) Thrust/fan input power (N/kw or Ib f /bhp) Required Statements:. The AMCA Certified Ratings Seal applies to airflow rate at free delivery only. Speed (rps or rpm) shown is nominal. Performance is based on actual speed of test.. Performance ratings include the effect of [list appurtenances here]. I. Rating Method "I" (Agricultural Fan, As Run Speed, Transmission Losses Included, Low Slip Motor) The performance ratings for each model number shall include: Airflow rate at 0 Pa (0.0 in. wg) and 0 Pa (0. in. wg) static pressure (Ratings at other static pressures are optional) Actual impeller speed at each point of rating or a nominal speed Airflow rate/motor input power (m /s/watt or cfm/watt) Motor nameplate voltage and frequency Motor manufacturer and model number for all motors listed for use on the fan Inlet air density (if other than standard air) Required Statements:. Speed (rpm or rps) shown is nominal. Performance is based on actual speed of test.. Performance ratings include the effect of [list appurtenances here]. J. Rating Method "J" (Direct Drive, PPV, As Run Speed) The performance ratings for each model number shall include: Airflow rate Rev. /0

49 Impeller speed Setback distance Tilt angle Motor/engine manufacturer and model number (for all motors/engines listed for use on the PPV) Required Statements:. Performance ratings include the effect of [list appurtenances here]. K. Rating Method "K" (Direct Drive, Circulator Fan, As Run Speed) The performance ratings for each model number shall include: Airflow rate Nominal impeller speed Airflow rate/motor input power (m /s/watt or cfm/watt) Motor nameplate voltage and frequency Required Statements:. The AMCA Certified Ratings Seal applies to airflow rate at free delivery only.. Speed (rpm or rps) shown is nominal. Performance is based on actual speed of test.. Performance ratings include the effect of [list appurtenances here]. L. Rating Method L (Induced Flow Fans) The performance ratings for each model number shall include: Inlet airflow rate Fan static pressure Fan input power Impeller speed Inlet air density (if other than standard air) Rev. /0

50 Fan static efficiency (optional) Outlet airflow rate Outlet area Nozzle velocity (Inlet airflow rate divided by nozzle discharge area) Required Statements:. Power rating (watts, kw, or bhp) does not include transmission losses.. Performance ratings do not include the effects of cross winds. A. Performance ratings do not include the effects of appurtenances (accessories). Or B. Performance ratings include the effects of [list appurtenances here]: M. Duct Statement Installation Method [this is different from the rating method; see test report for installation method; check one] For all rating methods, one of the following statements shall be shown immediately adjacent to the rating tables, graphs and charts: A B C D A & C B & D Performance certified is for installation type A Free inlet, Free outlet. Performance certified is for installation type B Free inlet, Ducted outlet. Performance certified is for installation type C Ducted inlet, Free outlet. Performance certified is for installation type D Ducted inlet, Ducted outlet. Performance certified is for installation type A & C Free or ducted inlet, Free outlet. Performance certified is for installation type B & D Free or ducted inlet, Ducted outlet. Note: Air curtains and air circulator fans do not require a duct statement. VI. ADDITIONAL REQUIREMENTS FOR AIR CURTAINS The velocity projection at standard inlet air density for one size of each product line shall be stated in the form of a table. The distance from the nozzle will be listed with the average core velocity. VII. ADDITIONAL REQUIREMENTS FOR AGRICULTURAL FANS Each fan appurtenance(s) (accessories) assembly shall have a distinct model number different from one without appurtenance(s) (accessories) or with a different group of appurtenance(s) (accessories). Rev. /0

51 VIII. ADDITIONAL REQUIREMENTS FOR POSITIVE PRESSURE VENTILATORS Each PPV appurtenance(s) (accessories) assembly shall have a distinct model number different from one without appurtenance(s) (accessories) or with a different group of appurtenance(s) (accessories). IX. ADDITIONAL REQUIREMENTS FOR CIRCULATOR FANS Each fan-appurtenance(s) (accessories) assembly shall have a distinct model number different from one without appurtenance(s) (accessories) or with a different group of appurtenance(s) (accessories). X. ADDITIONAL REQUIREMENTS FOR INDUCED FLOW FANS When electrical input power is cataloged, the tested motor shall be operated at the catalog voltage and frequency, or where a voltage range is stated, it shall be the mean voltage. In addition, the temperature of the motor winding has to be stable for each tested operating point. XI. MISCELLANEOUS ITEMS FOR ALL CATALOGS Where the ratings of licensed products are on the same page or "spread" as nonlicensed products, a clear physical separation and statement shall differentiate licensed products from nonlicensed products. Nonlicensed Sound Rating Statement Where sound ratings of a product which is not licensed to use the AMCA Certified Ratings Seal for Sound and Air are shown with licensed air performance ratings adjacent to the sound ratings, the following prominent statement shall be shown adjacent to the ratings: Partial Series of Sizes "The AMCA Certified Ratings Seal applies to air performance ratings only." When only a portion of a cataloged series of sizes are licensed, at least a majority of the sizes cataloged shall be licensed. The use of asterisks or similar marks to distinguish licensed products from nonlicensed products is unacceptable. In connection with nonlicensed products, the use of any phrase that is liable to be misinterpreted to mean that such products are licensed to use the AMCA International Certified Ratings Seal shall be prohibited. Phrases such as "tested and rated to AMCA International standards" or "rated to AMCA International standards" shall not be used. When a product is licensed for sound and air, the sizes shown for sound performance shall be the same as the sizes shown for air performance. There shall be no unauthorized use of AMCA International copyrighted material. See the AMCA International website for the policy on using AMCA copyrighted material. 0 Rev. /0

52 CHECKLIST: SOUND CATALOGS CATALOG IDENTIFICATION DATE OF CATALOG This check list should be used in conjunction with the air performance check list. I. PRODUCT LINES LICENSED FOR SOUND A. Octave Band and L W A Rating Qualifying Statements The following are the qualifying statements that shall be used with Sections B and C.. Figure, Fan Total Sound Testing Values shown are for (total L W or total L W A) sound power levels for: Installation Type A: free inlet, free outlet." Installation Type B: free inlet, ducted outlet. Ratings include the effects of duct end correction for the outlet duct." Installation Type C: ducted inlet, free outlet. Ratings include the effects of duct end correction for the inlet duct." Installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction for inlet and outlet ducts.". Figure, Fan Inlet Sound Testing "Values shown are for (inlet L Wi or inlet L Wi A) sound power levels for: Installation Type A: free inlet, free outlet." Installation Type B: free inlet, ducted outlet." Installation Type C: ducted inlet, free outlet. Ratings include the effects of duct end correction." Installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction.". Figure, Fan Outlet Sound Testing "Values shown are for (outlet L Wo or outlet L Wo A) sound power levels for: Installation Type A: free inlet, free outlet." Installation Type B: free inlet, ducted outlet. Ratings include the effects of duct end correction." Rev. /0

53 Installation Type C: ducted inlet, free outlet." Installation Type D: ducted inlet, ducted outlet. Ratings include the effects of duct end correction." B. Octave Band Ratings For a given rotational speed, a full set of octave band values may be presented for various points of rating. If only one set is presented, the value in each octave band shall be the maximum at any point of rating. The following statement shall be used: "The sound power level ratings shown are in decibels, referred to 0 - watts, calculated per AMCA International Standard 0. In addition, the appropriate statement from Section A shall be used to clarify installation type and end reflection. C. L W A Rating The following statement shall be used: "The A-weighted sound ratings shown have been calculated per AMCA International Standard 0." In addition, the appropriate statement from Section A shall be used to clarify installation type and end reflection. D. Fan Sone Rating Qualifying Statements. Fan Inlet Sone Rating For fans rated by a single value (hemispherical sone rating) use the following sentence: "The sound ratings shown are loudness values in fan sones at. m ( ft) in a hemispherical free field calculated per AMCA International Standard 0. Values shown are for: Installation Type A: free inlet hemispherical sone levels." Installation type B: free inlet hemispherical sone levels." Installation type C: ducted inlet hemispherical sone levels. Ratings do not include the effect of duct end correction." Installation type D: ducted inlet hemispherical sone levels. Ratings do not include the effect of duct end correction." For fans rated using spherical sone values, use the following sentence: The sound ratings shown are for loudness values in spherical sones at. m ( ft) in a spherical free field calculated per Annex B of AMCA. Values shown are for: Installation type A: free inlet spherical sone levels. Rev. /0

54 Installation type B: free inlet spherical sone levels. Installation type C: ducted inlet spherical sone levels. Ratings do not include the effect of duct end correction. Installation type D: ducted inlet spherical sone levels. Ratings do not include the effect of duct end correction.. Fan Outlet Sone Rating For fans rated by a single value (hemispherical sone rating) use the following sentence: "The sound ratings shown are loudness values in fan sones at a distance of. m ( ft) in a hemispherical free field calculated per AMCA International Standard 0. Values shown are for: Installation Type A: free outlet hemispherical sone levels." Installation type B: ducted outlet hemispherical sone levels. Ratings do not include the effect of duct end correction." Installation Type C: free outlet hemispherical sone levels." Installation type D: ducted outlet hemispherical sone levels. Ratings do not include the effect of duct end correction." E. Octave Band Ratings from In-Duct Tests For fans rated in eight octave bands from tests in accordance with ANSI/AMCA 0, the following statement shall be used: The sound power level ratings are shown in decibels, referred to 0 - watts, in a duct connected to either the inlet or the outlet of the fan, calculated per AMCA Standard 0. Values shown are sound power levels for: total fan sound calculated from inlet and outlet tests. the fan inlet. the fan outlet. F. Presentation of Sound Values For octave band and L w A ratings, round off the number to the nearest integer. Hemispherical sone values less than twenty shall be rounded to one tenth of a sone. Values of twenty or greater shall be rounded to the nearest integer. Spherical sone values shall be at a fan static pressure of Pa (0. in. wg). Ratings at other fan pressures are optional. Rev. /0

55 Spherical sone values greater than one and a half are rounded to the nearest one half sone. Spherical sone values greater than three tenths and less than or equal to one and a half are rounded to one tenth of a sone. Spherical sone values less than three tenths are rated as <0. Sones. Cataloged sound power data shall not be lower than db less than the data developed from the CRP- test data. Cataloged hemispherical sone or spherical sone ratings shall not be lower than sone (or %, whichever is less) from the value calculated from the sound power level data developed from the CRP- test data. G. A-Weighted Sound Pressure Levels and dba Ratings If A-weighted sound pressure levels or dba levels are displayed, the details of the calculation shall be shown, and the following statement shall be used: dba levels are not licensed by AMCA International. Rev. /0

56 AMCA CERTIFIED RATINGS SEAL AIR MOVEMENT APPLICATION FORM CRP & CRP T TO: AIR MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. We are submitting the enclosed test results (based on tests conducted in the AMCA Laboratory or in an AMCA Accredited Laboratory in accordance with ANSI/AMCA 0/ASHRAE, ANSI/AMCA 0, AMCA 0, AMCA 00, ASHRAE or an AMCA recognized test standard) along with the proposed catalog data, with a request for license to use the AMCA Certified Ratings Seal on the below listed product. Application for rating: Air Performance CFM/Watt Air Performance Efficiency Air Performance PPV Air Performance Induced Flow Fan Air Performance Smoke Management Fan Performance (CRP-T) Smoke Management Fan Performance Reversible Operation (CRP-T) Residential Air Performance Circulating Fan Performance Sound & Air Performance Efficiency Sound & Air Performance Induced Flow Fan Sound & Air Performance Residential Sound & Air Performance Inlet Sound Outlet Sound Total Sound One-third Octave Bands Octave Bands Hemispherical sones Spherical sones LwA Company Name Date Address Authorized Signature Print Name PRODUCT INFORMATION Product Name (As to be listed on License Appendix) SIZE MODEL NO. SIZE MODEL NO. SIZE MODEL NO. Rev. /0

57 SUMMARY OF TEST DATA USED FOR RATINGS Testing in an AMCA Testing Laboratory Testing in an AMCA Accredited Laboratory Location FAN TYPE: Agricultural Fan Air Curtain Axial Fan Ceiling Ventilator Centrifugal Fan Circulating Fan Energy Recovery Ventilator Evaporative Cooler Induced Flow Fan Jet Tunnel Fan Mixed Flow Fan Positive Pressure Ventilator Propeller Fan Power Roof Ventilator Smoke Management Fan Other Production Sample Pre-Production Sample Test Number Test Standard Figure No./Installation Type Date of Test Model Number Test Speed (rpm) Impeller Diameter Number of Blades Blade Pitch Angle ( ) Curb Height (inches) Sizes Rated from this Test Other Appurtenances Used During Testing Inlet Bell Shutter/Damper Screen(s) Other Method used for calculating sound ratings (if applicable): Full Octave Bands One-Third Octave Bands Generalized Method Specific Method Belt Drive Direct Drive Rating Method: A - Constant Speed, Transmission Loss Not Included B - Constant Speed, Transmission Losses Included C - As Run Speed, Transmission Losses Included, Low Slip Motor D - Direct Drive, Constant Speed, Low Slip Motor E - Direct Drive, As Run Speed, Low Slip Motor F - Direct Drive, As Run Speed, High Slip Motor G - Air Curtain H - Direct Drive, Jet Tunnel Fan, As Run Speed I - Agricultural Fan, As Run Speed, Transmission Losses Included, Low Slip Motor J - Direct Drive, PPV, As Run Speed K - Direct Drive, Circulator Fan, As Run Speed L Induced Flow Fans Rev. /0

58 AMCA CERTIFIED RATINGS SEAL AERODYNAMICALLY SIMILAR APPLICATION FORM CRP A TO: AIR MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Please accept this application to extend the license to use the AMCA Certified Ratings Seal to the product listed hereon. This product is aerodynamically similar to our product, which is licensed to bear the AMCA Seal under our License Appendix No.. Application for rating: Air Performance Air Leakage CFM/Watt Air Performance Efficiency Air Performance PPV Air Performance Induced Flow Fan Air Performance Residential Air Performance Smoke Management Fan Performance Smoke Management Fan Performance Reversible Operation Water Penetration Wind Driven Rain Sound & Air Performance Efficiency Sound & Air Performance Induced Flow Fan Sound & Air Performance Residential Sound & Air Performance Inlet Sound Outlet Sound Total Sound One-Third Octave Bands Octave Bands Hemispherical Sones Spherical Sones LwA Company Name Date Address Authorized Signature Print Name PRODUCT INFORMATION Aerodynamically Similar Product Name: (As to be listed in the Directory) Originally Licensed Product Name: Rev. /0

59 SIZE AERODYNAMICALLY SIMILAR PRODUCT MODEL NUMBER ORIGINALLY LICENSED PRODUCT MODEL NUMBER Rev. /0

60 AMCA CERTIFIED RATINGS SEAL NAMEPLATING APPLICATION FORM CRP B TO: AIR MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Please accept our application for license to use the AMCA Certified Ratings Seal on the product listed hereon. We are purchasing this product under brand naming arrangement from. (Original Licensee) Application for rating: Air Performance Air Leakage CFM/Watt Air Performance Efficiency Air Performance PPV Air Performance Induced Flow Fan Air Performance Residential Air Performance Smoke Management Fan Performance Smoke Management Fan Performance Reversible Operation Water Penetration Wind Driven Rain The Original Licensee is currently licensed to use the AMCA Seal on the product referenced hereon and is in full agreement with the content of this application. We understand that the license to use the AMCA Seal is dependent on the Original Licensee maintaining full compliance with AMCA's Certified Ratings Program. Sound & Air Performance Efficiency Sound & Air Performance Induced Flow Fan Sound & Air Performance Residential Sound & Air Performance Inlet Sound Outlet Sound Total Sound One-Third Octave Bands Octave Bands Hemispherical Sones Spherical Sones LwA Applicant Company Company Address Authorized Signature Print Name Title Date We have examined this application and its content and we fully endorse it. Original Licensee Address Authorized Signature Date Print Name Title Rev. /0

61 PRODUCT INFORMATION Applicant Company Product Name (As to be listed in the Directory) Original Licensee Product Name (As to be listed in the Directory) APPLICANT ORIGINAL LICENSEE SIZE MODEL NUMBER SIZE MODEL NUMBER Rev. /0

62 AMCA CERTIFIED RATINGS SEAL ALTERNATE MANUFACTURER APPLICATION FORM CRP L TO: AIR MOVEMENT AND CONTROL ASSOCIATION INTERNATIONAL, INC. Please accept our application for license to use the AMCA Certified Ratings Seal on the product listed hereon. We are manufacturing this product licensing arrangement from. (Original Licensee) Application for rating: Air Performance Air Leakage CFM/Watt Air Performance Efficiency Air Performance PPV Air Performance Induced Flow Fan Air Performance Residential Air Performance Smoke Management Fan Performance Smoke Management Fan Performance Reversible Operation Water Penetration We certify that our product is identical to that produced by the Original Licensee. The Original Licensee is currently licensed to use the AMCA Seal on the product referenced hereon and is in full agreement with the content of this application. We understand that the license to use the AMCA Seal is dependent on the Original Licensee maintaining full compliance with AMCA's Certified Ratings Program. Sound & Air Performance Efficiency Sound & Air Performance Induced Flow Fan Sound & Air Performance Residential Sound & Air Performance Inlet Sound Outlet Sound Total Sound One-Third Octave Bands Octave Bands Hemispherical Sones Spherical Sones LwA Wind Driven Rain Applicant Company Company Address Authorized Signature Print Name Title Date We have examined this application and its content and we fully endorse it. Original Licensee Address Authorized Signature Date Print Name Title Rev. /0

63 PRODUCT INFORMATION Applicant Company Product Name (As to be listed in the Directory) Original Licensee Product Name (As to be listed in the Directory) APPLICANT ORIGINAL LICENSEE SIZE MODEL NUMBER SIZE MODEL NUMBER Rev. /0

64 CATALOG CHECKING CHARGES Effective December, 00 PRINT CATALOGS Performance Data Check (Per Product Line) Air Performance... $0.00 Sound Performance... $0.00 Louver or Damper... $0.00 Airflow Measurement Station... $.00 Acoustical Duct Silencer... $.00 Format Check Pages or Less... $.00-0 Pages... $ Pages... $0.00 Catalog Revision, Performance Data Not Altered (Per Product Line) Spot Check... $.00 Brand Naming Products, CRP-B Forms (Per Product Line) Performance data and format comparison... $0.00 Alternate Manufacturers, CRP-L Forms (Per Product Line) OEM Catalog... $0.00 Own Catalog... $0.00 ELECTRONIC CATALOGS First Version... $00.00 Revised Version... $0.00 Format Check Data Check CATALOGS REQUIRING CORRECTIONS AS A RESULT OF ST REVIEW Second Review... $.00 Third Review... $0.00 Second Review...0% of data check fee Third Review...% of data check fee FEES ARE SUBJECT TO CHANGE WITHOUT NOTICE Rev. //0