BARDON T01-C TOUCHLESS URINAL SENSOR INSTALLATION INSTRUCTIONS K-8787T-C02(DC/ ) K-8787T-C04(AC/ ) 18 E

Size: px

Start display at page:

Download "BARDON T01-C TOUCHLESS URINAL SENSOR INSTALLATION INSTRUCTIONS K-8787T-C02(DC/ ) K-8787T-C04(AC/ ) 18 E"

Howard Melton
5 years ago
Views:

1 BARDON TOUCHLESS URINAL SENSOR INSTALLATION INSTRUCTIONS K-8787T-C0(DC/ ) K-8787T-C04(AC/ ) Please read these instructions carefully to familiarize yourself with the required tools, materials, and installation sequences. Follow the sections that pertain to your particular installation. This will help you avoid costly mistakes. In addition to proper installation, read all operation and safety instructions. All information in these instructions is based upon the latest product information available at the time of publication. Kohler China reserves the right to make changes in product characteristics, packaging, or availability at any time without notice. These instructions contain important care, cleaning, and warranty information - please leave instructions for the consumer. RECOMMENDED TOOLS AND MATERIALS Open end/adjustable wrenches Tape measure Basin wrench Pipe wrench Square Level Pliers Socket wrench with sockets Screw driver Seal tape Connection wire Wire cutter Insulation tape Bushing SENSOR SPECIFICATION Model 8787T-C0(DC) 8787T-C04(AC) 4 " AA" size alkaline batteries Power (8787T-C0) 0V AC 50/60Hz(8787T-C04) Temperature Environmental temperature: 1 to 60 Starting pressure 0.05~0.7MPa Sensing distance 80cm away from sensing window (adjustable) Testing time About seconds (or set to 5 seconds) - / 8787T-C0( ) 8787T-C04( ) 4 5 (AA 4) (8787T-C0) 0V AC 50/60Hz(8787T-C04) : 1 ~ ~0.7MPa 80cm ( ) ( 5 ) Note: the sensing distance in the table is measured with a 30 30cm white board as the reflecting surface. 18 E , 007 Copyright Kohler China Ltd., 007

2 PRODUCT PAGE Stop Valve Assy T-NA 8787T-C04 use only 8787T-C04 AC Connector Big "O" Ring "O" Adjustment Nut Adjusting Bolt Small "O" Ring "O" Center Unit Spring Nut Inlet Connection Connection "O" Ring "O" Pertain SC CP Sensor Cover Screw(4 Pcs) M3x8 (4 ) M3x Rubber Plugs Bracket Plug In Long Screws (4 Pcs) Angles M4 50 (4 ) M Sensor Lens Cover Screw ( Pcs)M3 6 ( ) M3 6( ) Control Box Battery Seal Washer Cover Solenold Valve Assy Flushing Valve Assy. Connection "O" Ring "O" Outlet Connection Pertain 1090 Control Box Assy. Nut Fixed Cap Big "O" Ring "O" Filter --

3 ROUGHING-IN UNIT: mm K-5016T-ET K-5016T-ER R1/ R1/ /" /4" SPUD " N.P.S. TAP 445 " N.P.S. TAP Notice: The dimensions above are just for reference. The connection take between the outlet connection and urinal is not supplied in this package. Notice: To ensure an effective flush performance, strongly recommended inner diameter of water supply (including water meter, valve, etc.) is no less than 5mm, and supplied water pressure (sensor inlet dynamic pressure) is 0.18MPa ~0.55MPa (Go with K-5016T). ( ) 5mm ( ) 0.18MPa ~0.55MPa ( K-5016T) INSTALLATION 1. Determine the installation location per rough-in dimensions. Chisel out a slot and install the supply tubing. Turn off the water supply. The depth of the slot is no less than 105mm, see the figure to the right for rough-in dimension requirement. While installing 8787T-C04(AC), chisel out the slot indicated in the dot line area of figure right for installation of bushing. 50 Install Bushing Notice: installation location: No light shall enter or be reflected into the sensing window. No reflectible objects in front of the sensing window (e.g., mirror, polishing stainless steel and some other polished plate). c. No strong ultraviolet radiation or electromagnetic field nearby mm 8787T-C04( ) Installation Site ( ) c. -3-

4 È Remove the dust-proof covers from the valve and install the inlet/outlet connections. The outlet connector shall face away from the wall and at the center of the urinal. Place the flushing valve box into the slot, adjust its level and square with battens. Then screw down the nut at the inlet and outlet position. The connections please refer to the roughin in page 3. Water Supply(Recommended Inner Diameter Is More Than 5mm) ( 5mm) Inlet Connection Nut. 3 Connect control box while installing 8787T-C T-C04 AC Power Unit Outer diameter of bushing is no more than 5mm 5mm Battens Outlet Connection Nut Please directly reference to Step 3 when installing 8787T- C0 (DC). Please match 16305T-NA AC power unit when installing 8787T-C04 (AC). The way of installation is as below. CAUTION: Outlet of AC power unit upward prohibited. Do not connect 0V AC power supply to DC wiring terminal. c. Do not damage the covering of AC power unit or remove screws to avoid leakage. 8787T-C0( ) 3 Connect to sensor Outlet downwards Connect to AC Power supply Connect to AC Power supply Outlet upwards Connect to sensor 8787T-C04( ) 16305T-NA 0V c. A. Fig. #1: AC power unit connection way 1: AC power unit is directly connected to electric control box. AC Connector Fig. # : AC power unit connection way : AC power unit is connected to electric control box by connection wire. A T-NA AC power unit AC Connector Fig. #1 1 Wire prepared by customer Connector 16305T-NA AC Power Unit Connect with the same color wire, and protect connect area by insulation tape. Fig. # -4-

5 B. When installing the AC power unit in cassette, please layout the bushing according to Fig. #3, and thread the wire through the bushing. Fig. #3: Connection sketch AC power unit install in cassette. CAUTION: One AC power unit can supply two sensors at most. Bushing Connect 0V AC 0V B. 3 C. When installing the power unit on the ceiling, please layout bushing according to Fig. #4 and thread wire through the bushing. Fig. #4: Connection sketch while installing power unit on the ceiling. CAUTION: One AC power unit can supply two sensors at most. Fig. #3 3 Ceiling AC Power Unit Bushing C. 4 Notice: Keep the connector away from water. Don t mistake the direction of inlet and outlet. c. Do not connect the DC output of AC power unit to AC power supply. d. Do not connect to power supply while installing. Connection line is not supplied. AC connection wire with insulating sleeving is recommended. Wire of which the nominal section area of conductor is not less than 0.5mm is also recommended. DC connection line use wire of which the nominal section area is not less than 0.3mm. It is cut according to acted installation requirements(the length of cut wire is recommended less than 10m). e. The head AC power supply must be protected with appropriate fuse. f. Please confirm the AC power supply and water supply should be shut off before maintaining the products with AC power related. g. Don't lose the connection O rings. : c. d. 0.5mm 0.3mm ( 10m) e. Fig. #4 4 f. g. O -5-

6 3. Connect the control box with power on with solenoid valve(see step 5), and check the leakage by manual flushing for several times. Once it is confirmed that there is no leakage, place the mold sheath onto the valve box and apply slurry into the crevice around the valve box and smooth the surface. Notice: Please confirm the completion of step. Please avoid the damage of the sensor cover or breaking the cord. 3. ( 5) Valve Box 40 Tiles Slurry Mold 4. When the slurry turns solid, remove the short screws, pull out slurry mold, mount the bracket assy, and secure with long screws. Slurry Mold 4. Short Screw M4 10 M While using DC power for 8787T-C0, remove the battery cover and put in 4 AA size alkaline batterise and tighten the screwscrews. Connect solenoid valve with control box assy at last. While using AC power for 8787T-C04, connection solenoid valve with control box assy, and then connect AC power supply to AC power unit. Install the cover as show in the figure: Buckle the sensor cover into the wall slightly above bracket assy. Press the sensor cover down along the wall and fit tightly into the bracket assy. c. Push upward with basin wrench and rotate clockwise to lock the sensor cover. Screw M3 8 M3 8 a T-C0( ) T-C04( ) b c. ( ) -6-

7 Notice: Don' t mistake the polar of the batteries and don' t mix new and used batteries together. When no enough power, the indicator will flash continuously (0 times at most). When out of power, the indicator will flash every seconds and the sensor will not work until new batteries are supplied. When changing, remove the battery cover and put in new batteries. No need to reset the program after the battery changed. Put on clean gloves when install sensor cover to avoid surface injury by cement or sand. Indicator ( 0 ) c 90 o Battery Indicator INSTALLATION IN OTHER METHODS Prefabricated Board Decorating Panel a Installation On Prefabricated Board b Installation On Decorating Panel USER S GUIDE Don' t use this system until the power is on for minutes. The sensing distance will be adjusted and the system will not work during this time. Working Status Users can set the working status as needed per the table below by turning on the right switch. The four status options, SW1, SW3, and SW4, have been set ON statuses and SW has been set OFF status in the factory. After setting, plug the rubber plug tightly. OFF SW1 SW3 SW4 ON SW Switch ON OFF SW1 (pre-flushing) Yes(3s) No SW (testing time) About 5s About s SW3(flushing cycle when no using) 4 hours 8 hours SW4 (manual flushing) Yes No ON 134 ON OFF SW1 ( ) SW ( ) 5 SW3 4 8 ( ) SW4 ( ) -7-

8 Deodorizing Flushing The urinal will take a big flush automatically when it s used 3 or 4 times in minutes. 3-4 Manual Flushing Approach the supplied special magnetic stick (flushing control stick) to the left part of the sensor lens. The system is now at a manual status and the indicator will flash every seconds. Approach the flushing control stick to the window, it ll start to flush; approach again, stopping flushing. This status will last for 8 minutes until it turns to the normal working status. (The flushing, if any, will be terminated when this status ends). Notice: The longest flushing time is 30 seconds once. If the flushing control stick keeps near to the sensing window, the manual status will be terminated automatically and reassume the normal working status Flushing Control Stick ( ) 8 ( ) Sensing Distance The first 10 minutes with power supply is the time for adjusting sensing distance. Use a cross screwdriver. If this is not accomplished within 10 minutes, shut off the power. Wait for the indicator to stop flashing. Turn on the power supply and repeat the procedure The sensing distance is set to its max. value in factory. The angle of ultra-red radiation is 15 degrees down. It s adjustable when the bathroom is narrow and crowded. When adjusting, remove the panel and the rubber plug, and adjust the potentiometer. Make sure to insert the rubber plug back firmly when finished. 15 o Notice: The scope of the screwdriver which is used to adjust the induction distance should not be larger than mm, so as not to damage the potenpiometer. (Increase) mm (Decrease) Flushing Volume Adjust when required. Remove the sensor cover. Turn the adjusting bolt to a proper place. Adjusting Bolt -8-

9 MAINTENANCE Urinal Repair When repairing, you don' t have to dismount the sensor. Cover the sensing window with tape and work with ease. Notice: Don' t use very adhesive tape in case the scar Clean the Filter Screen If the flushing volume reclines sharply after installation or used for a long time with no cause from water pressure, the filter may need a wash. Turn off the fixed cap with filter-key, take out the filter, clean with a brush and reinstall it. Notice: Turn off the water supply or tighten the adjusting bolt before cleaning. Filter Fixed Cap Filter-key Care & Clean Keep the sensing window clean. Wipe with soft cloth and mild cleaner. Notice: Do not use dust-removing powder, abrasive powder or cleaner containing oil, acid or alkaline ingredient. Do not spray air-refresher, disinfector, or other deodorizing, cleaning solvent directly into the sensing window. c. Keep wire away from water. d. Don' t attack the sensor window. c. d. -9-

10 TROUBLESHOOTING Please make following checks before repair: Symptoms Probable causes Corrective action No flushing (Indicator not flashing) No flushing or poor flushing while the indicator can flash Keep flushing indicator not flashing Battery indicating light keeps flashing and no flushing 1. No power or mistake connected. There is an object within the sensing distance 3. The sensing window needs cleaning 1. Still in the waiting status. Adjusting bolt not fully open 3. Low water pressure 4. Filter is obstructed 5. Manual status Dirt in valve unit Out of electricity (Only for 8787T-C0) 1. Check the power connect. Remove the object or reduce the sensing distance 3. Clean the window 1. Wait for 10 minutes. Open the adjusting bolt 3. Improve water supply 4. Clean the filter 5. Terminate manual status or wait for the status to end Repeat the sensing action several times after cleaning the filter Replace batteries (Only for 8787T-C0) If the trouble remains after above-mentioned actions are taken, please contact with us via distributor. ( ) ( 8787T-C0 ) ( 8787T-C0 ) -10-

11 IMPORTANT CONSUMER INFORMATION Consumer Responsibilities 1. Do not attack the sensor.. Do not directly flush the sensor with water. The sensor is an electronic instrument. 3. Do not let sunlight or other light source enter or be reflected into Sensor Window. 4. Do not hang on the opposite wall any reflective items or install light/electronic sensor such as toilet flushing sensor. 5. Do not make Sensor Window near strong ultraviolet or electromagnetic field. 6. Keep the sensor window clean. The sensor cover can be cleaned by soft rag with neutral liquid detergent. Do not use eradicator, abrasive powder or oil, acid or alkali liquid detergent. Do not spray air freshener, disinfectant or other kinds of odious removing, cleaning organic liquid to the sensor directly. 7. Urinal is designed for use with potable water. Avoid water that includes a lot of contaminants or acid/alkali water and impure water ( ) 8. When AC power unit is connected to 0V AC power supply, corresponding protective measures should be taken. 9. Please confirm no water penetration at the connection area of AC wire, and the connection area is not easy to be affected by damp. 10. Don t connect power unit to AC power supply until the sensor installation is finished. 11. The head AC power supply must be protected with appropriate fuse. 1. Please confirm the AC power supply and water supply should be shut off before maintaining the products with AC power related. 13. All electrical connection must be compliance with related regulation and codes. 14. All installation staff should be well familiar with installation instruction. 8. 0V

8791T-C02( ) 8791T-C04(AC) 8791T-C04( ) size alkaline batteries(8791t-c02) 2 7 (AAA 2)(8791T-C02) 220V AC 50/60Hz(8791T-C04)

8791T-C02( ) 8791T-C04(AC) 8791T-C04( ) size alkaline batteries(8791t-c02) 2 7 (AAA 2)(8791T-C02) 220V AC 50/60Hz(8791T-C04) PATI URINAL SENSR INSTALLATIN INSTRUCTINS K-8791T-C0(DC/ ) K-8791T-C04(AC/ ) Please read these instructions carefully to familiarize yourself with the required tools materials and installation sequences.