GCL-GT HEAVY-DUTY GEAR HEAD TROLLEY OPERATOR

Size: px

Start display at page:

Download "GCL-GT HEAVY-DUTY GEAR HEAD TROLLEY OPERATOR"

Lindsay Pearson
5 years ago
Views:

1 GCLGT HEAVYDUTY GEAR HEAD TROLLEY OPERATOR Single Phase MODULE MOUNTING LOCATIONS TROUBLE SHOOTING LEDs BOARD PORT LIMIT SENSOR HOIST MOTOR S GROUND NOT FOR RESIDENTIAL USE 208/230V 1PH 115V 1PH ROUTE LOW ERNAL (CLASS 2 CONNECTIONS) CONTROL WIRE FUSE GDB 250 ma OR S ma ERNAL ANTENNA CONNECTION (COAX) INTERNAL BOARD SECONDARY FUSE GDB 2.5A OR S A BRAKE CIRCUIT BREAKER (CERTAIN MODELS ONLY) S INPUT POWER

2 GCLGT HEAVYDUTY GEAR HEAD TROLLEY OPERATOR Single Phase 24 VOLTS DC TROUBLESHOOTING LED s ENABLE ON = ENABLED OFF = DISABLED ON = POWER AVAILABLE OFF = CHECK AC POWER SUPPLY. CHECK FUSES 24 VDC ENAB ERNAL WIRING DIAGRAM 1BTN NO NO 3BUTTON * * MULTIPLE 3BUTTON INSTALLATIONS REQUIRE THE BUTTON TO BE WIRED IN SERIES. See Fig. 5, pg 5.4 IF BUTTON IS USED 1BTN KEY CARD READER O/C PULL SERIES II SAFETBEAM () (* CONNECT WIRES TO EITHER TERMINAL) * 115V 208/230V WHEN INSTALLING ERNAL SENSING EDGE (DO NOT CONNECT 2WIRE MONITORED SENSING EDGE TO THESE INPUTS) IN POWER CONNECTIONS L1/ L1 N/ L2 (HOT) NEUTRAL 1 2 PWR mA MAX CURRENT PWR RAD RELAY NOM 24VDC THRUBEAM PHOTOCELLS P/N

3 GCLGT HEAVYDUTY GEAR HEAD TROLLEY OPERATOR Three Phase MODULE MOUNTING LOCATIONS TROUBLE SHOOTING LEDs BOARD PORT LIMIT SENSOR HOIST MOTOR S GROUND NOT FOR RESIDENTIAL USE 208/230V 3PH 460V 3PH L1 L2 L3 ROUTE LOW ERNAL CONTROL WIRE FUSE GDB 250 ma OR S ma ERNAL ANTENNA CONNECTION(COAX) INTERNAL BOARD SECONDARY FUSE GDB 2.5A or S A BRAKE S INPUT POWER

4 GCLGT HEAVYDUTY GEAR HEAD TROLLEY OPERATOR Three Phase 24 VOLTS DC TROUBLESHOOTING LED s ENABLE ON = ENABLED OFF = DISABLED ON = POWER AVAILABLE OFF = CHECK AC POWER SUPPLY. CHECK FUSES 24 VDC ENAB ERNAL WIRING DIAGRAM 1BTN NO NO 3BUTTON * * MULTIPLE 3BUTTON INSTALLATIONS REQUIRE THE BUTTON TO BE WIRED IN SERIES. See Fig. 5, pg 5.4 IF BUTTON IS USED 1BTN KEY CARD READER O/C PULL SERIES II SAFETBEAM () (* CONNECT WIRES TO EITHER TERMINAL) * L1 IN POWER CONNECTIONS L2 WHEN INSTALLING ERNAL SENSING EDGE (DO NOT CONNECT 2WIRE MONITORED SENSING EDGE TO THESE INPUTS) L3 PWR mA MAX CURRENT PWR RAD RELAY NOM 24VDC THRUBEAM PHOTOCELLS / V P/N

5 GCLGT HEAVYDUTY GEAR HEAD TROLLEY OPERATOR 575 Volt Phase MODULE MOUNTING LOCATIONS TROUBLE SHOOTING LEDs BOARD PORT LIMIT SENSOR HOIST MOTOR GROUND NOT FOR RESIDENTIAL USE 575V 3PH L1 L2 L3 ROUTE LOW ERNAL CONTROL WIRE FUSE GDB 250 ma OR S ma ERNAL ANTENNA CONNECTION(COAX) INTERNAL BOARD SECONDARY FUSE GDB 2.5A or S A BRAKE S INPUT POWER

6 GCLGT HEAVYDUTY GEAR HEAD TROLLEY OPERATOR 575 Volt Phase 24 VOLTS DC TROUBLESHOOTING LED s ENABLE ON = ENABLED OFF = DISABLED ON = POWER AVAILABLE OFF = CHECK AC POWER SUPPLY. CHECK FUSES 24 VDC ENAB ERNAL WIRING DIAGRAM 1BTN NO NO 3BUTTON * * MULTIPLE 3BUTTON INSTALLATIONS REQUIRE THE BUTTON TO BE WIRED IN SERIES. See Fig. 5, pg 5.4 IF BUTTON IS USED 1BTN KEY CARD READER O/C PULL SERIES II SAFETBEAM () (* CONNECT WIRES TO EITHER TERMINAL) * L1 IN POWER CONNECTIONS L2 WHEN INSTALLING ERNAL SENSING EDGE (DO NOT CONNECT 2WIRE MONITORED SENSING EDGE TO THESE INPUTS) L3 PWR mA MAX CURRENT PWR RAD RELAY NOM 24VDC THRUBEAM PHOTOCELLS V P/N

60 Series Engine Controls

ECU 60 Series Engine Controls Use CAUTION since you are applying 120VAC RMS to the AC Input terminals and that it is always potentially their during engine run!!! ECU is a registered trademark of Engineering