AddBlueOff Auto Pass V2. Installation guide. AUTO Pass. by ADDBlueOFF.net. Version 2

Transcription

1 Installation guide AUTO Pass by ADDBlueOFF.net Version 2 1

2 Contents Module description MAN install recommendation... 8 Modules Inputs / Outputs Pin assignments Module modes Module installation. 3 DAF install recommendation... 4 IVECO install recommendation... 5 FORD Cargo install recommendation Renault install recommendation.. 9 SCANIA install recommendation VOLVO install recommendation Mercedes install recommendation Warranty Kit Technical specification The CAN bus interface module (Emulator), in follow Module, is used for simulate working after treatment exhaust system (SCR) for DAF, IVECO, MAN, FORD, Renault, Volvo, Scania and Mercedes * trucks and NOx sensor. The Module receive the data from CAN bus, calculate needed values and NOx, after this transmit to engine ECU. It is connected to the vehicle CAN bus and adjusted on the software The Module has pins for connect to the power and to the CAN bus. Module description Module Inputs / Outputs and hardware levels in accordance with the developer of CAN bus Robert Bosch GmbH. The Module can be installed as on the vehicles with working SCR system, as on the vehicles with critical faults in SCR system and NOx sensors. * - On the Mercedes trucks may be appeared errors by air pressure, but this error doesn t reduce the power. The numeration of the pins you can see on the picture, view from the cable. The Modules are not marked for identification the version on the top of CAN bus filter, like Black Pass versions. No Mark NOTE: In some cases, during the installation may need to connect additional resistance (terminator) for the right operation the CAN bus, it is necessary to close the JP1 on the emulator. 1 4 JP1 Table 1. Modules Pin assignments Color Type Function Current, ма 1 Red / Green Power Module source +12/24 V 40 2 Gray / White Power Ground - Terminal 31-3 Yellow / White CAN CAN-High - 4 Blue / Black CAN CAN-Low - 2

3 Pin 1. Module source. Must be connected to the power after ignition +24V (terminal 15). Pin 2. Ground Terminal 31. Must be connected to the ground of the vehicle (terminal 31). Module pin assignments Module modes The Module is selling in the programmed state. After installation the Module will be activated automatically. NOTE! The Module can be activated only once, but after activation can work on the same type trucks. Ex. If Module was activated at the MAN TGS truck can work at the MAN TGX truck too. Pin 3. CAN bus. Must be connected to the CAN High line of the CAN bus. Pin 4. CAN bus. Must be connected to the CAN Low line of the CAN bus. The Module working modes can be recognized by LEDs states (Table 2. LEDs states). VD10 VD8 Table 2. LEDs states LEDs State Working modes Description 1 Steady light VD8 Not activated The Module is powered. Are not data in CAN bus or incorrect connection the Module to the CAN bus. 2 VD6 VD 10 flashing Simulation mode The Module is powered. Module is getting data from engine. 3 The Module is powered. Are not data in VD8 flashing by 0.3 Activated, waiting CAN bus or incorrect connection the sec interval mode Module to the CAN bus. If Module was activated and engine wasn t in CAN bus after power switch on, Module will be work in mode 2 during 1 sec, after this mode will be changed on 3. The Module installation includes: 1. Power disconnection from SCR system and NOx sensor. 2. Connection Module to the CAN bus. 3. Control of the installation and erasing fault codes (if it is necessary) NOx sensor and dosing module of the SCR system are connected to the CAN bus. Before the installation of the Module dosing module and NOx sensor must be disconnected from the power. Module installation It may be complete by two ways: to remove supply fuses or to disconnect the supply wires from the pump module SCR and NOx sensor. For NOx sensor to disconnect from terminal 15 (ignition). For pump module of SCR system to disconnect from terminal 15 (ignition) and terminal 30 (battery). 3

4 Connection diagram DAF install recommendation The Module can be connected to the socket located in the transitional shield cabinframe at DAF trucks under the hood. Pic.2 Pic.1 The CAN bus of the Module must be connected to the 12С connector (Pos С1, Pic.2). NOTE: Pin assignment may be diffirent, depends from year of truck manufacture. The connection is made to the twisted pair (CAN bus) Red / Yellow wires, according to the diagram. Module power connected to a thick red wire in the connector 12C to the terminal 15 (+24V after ignition). Power disconnection. For disconnect the power from SCR system and NOx sensor necessary disconnect the Yellow socket (Picture below and Pic. 2 Pos. А9). Black Pass 4

5 Connection diagram The Module can be connected at IVECO trucks to the OBD II socket located in the fuses shield. IVECO install recommendation The Module must be connected according the schematic diagram below. Black Pass Module The pin assignment of the OBD II connector shown below. The Module must be powered from the terminal 15 (+24V after ignition). 5

6 Power disconnection for IVECO Stralis. For disconnect the power from SCR system and NOx sensor should cut the wires 7540 (Red pin 25) and 8540 (Green pin 26) at the connector Е, located in the transitional shield cabin-frame under the hood. Power disconnection for IVECO Traker. For disconnect the power from SCR system and NOx sensor should cut the wire 7540 (Red pin 25) at the socket Е, located in the transitional shield cabin-frame under the hood, wire 8540 (Green pin 24) at the Dosing module socket and wire 8173 (Green pin 1) at the NOx sensor socket. 6

7 Power disconnection for IVECO EuroCargo For disconnect the power from SCR system and NOx sensor should cut the wires 7540 (Red pin 3,4), 8540 (Green pin 24) at the Dosing module socket and wire 8540 (Green pin 18) at the socket Е, located in the transitional shield cabin-frame under the hood. Connection diagram The Module can be connected at FORD Cargo trucks to the OBD II socket located in the fuses shield. FORD Cargo install recommendation The Module must be connected according the schematic diagram below. Black Pass Module 7

8 The pin assignment of the OBD II connector shown below. The Module must be powered from terminal 15 (+24V after ignition). Power disconnection. terminal 30 For disconnect the power from SCR system and NOx sensor should pull out the fuses of terminal 30 and terminal 15. See the picture. terminal 15 Connection diagram The Module can be connected at MAN trucks to the socket located in the transitional MAN install recommendation shield cabin-frame under the hood at the driver side. The Module must be powered from X3437 socket: terminal GND The CAN bus must be connected to Х1549 socket: 191 CAN High 192 CAN Low 8

9 NOTE: The JP1 on the Module must be close for coming back the CAN bus working resistance. Power disconnection. For disconnect the power from SCR system and NOx sensor should disconnect Х4680 socket located in the transitional shield cabin-frame under the hood at the driver side. Connection diagram Renault install recommendation The Module can be connected at Renault trucks to the OBD II socket located under the instrument cluster at the left side. The Module must be connected according the schematic diagram below. Black Pass Module The pin assignment of the OBD II connector shown on the picture. 9

10 Power disconnection. For disconnect the power from SCR system and NOx sensor should pull out the fuse (10A) of terminal 15 (F107, Pos. P59) at the fuses shield. See the pictures below. Connection diagram The Module can be powered at SCANIA trucks from C103 socket located in the transitional shield cabin-frame under the hood to terminal 15. See pictures below. SCANIA install recommendation The CAN bus of the Module must be connected to C462 socket (three pins) (ENGINE FRAME), located under cabin near the ECU. See picture below. NOTE: can erase fault codes at Scania trucks (cannot erase exceed NOx codes). For erasing fault codes needs switch on the ignition, wait 10 sec, start engine, at the idle mode wait 30 sec, stop engine, wait 30 sec and repeat this operations 4 times. 10

11 The Module must be connected according the schematic diagram below. terminal 15 Black Pass Module Power disconnection. For disconnect the power from SCR system and NOx sensor should cut the wires FFC12 and FFC16 at the C103 socket (see pic. Above) and pull out the fuse of F42 at the fuses shield. See the pictures below. Connection diagram VOLVO install recommendation The Module can be connected at Volvo trucks to the OBD II socket located in the instrument cluster at the left side. The Module must be connected according the schematic diagram below. 11

12 Black Pass Module The pin assignment of the OBD II connector shown on the picture. Power disconnection. For disconnect the power from SCR system and NOx sensor should pull out the fuse F10 (10A) of terminal 15 at the fuses shield. See the pictures below. 12

13 Connection diagram Mercedes install recommendation The Module can be connected at Volvo trucks to the OBD II socket located in the instrument cluster at the left side. The Module must be connected according the schematic diagram below. Black Pass Module The pin assignment of the OBD II connector shown on the picture. Power disconnection. For ACTROS truck must be pull out the F1 (15А) fuse in the А1 module (See pic. Power disconnection ACTROS), for AXOR, ATEGO pull Pic. Power disconnection ACTROS out the F11 (15А) А1 module (See pic. Power disconnection AXOR, ATEGO). 13

14 Pic. Power disconnection AXOR, ATEGO LLC "VK Electronics" guarantees that the equipment's specification and its performance during the warranty period. In the event of a warranty case is obliged to make, at its sole discretion repair or replace - in the terms established by law. The warranty is valid for the period specified technical center by installing this equipment. LLC "VK Electronics" may refuse to guarantee the following reasons: Damage of the equipment associated with mishandling in storage, installation and operation specified in the documentation of the equipment. Installation of the equipment in the noncertified centers. Warranty Kit Violation of factory seals (if provided by the manufacturer) or the presence of traces of intervention equipment. Warranty does not cover LED status indicator, and any supporting products supplied with this type of equipment. LLC "VK Electronics" is not responsible for the costs incurred due to the removal or replacement of faulty equipment, as well as any other random and non-random damage to the vehicle and its equipment, factory and additionally installed. For warranty contact the organization engaged in the sale and installation of equipment on the vehicle, or to any authorized dealer of "VC Electronics". Denomination Quantity CAN adapter 1 Electronic cable (4 pin) 1 USB adapter 1 Plastic box 1 Screw 8 Package 1 14

15 Technical specifications Property Value Power supply, V Power consumption, ма 40 Cable length, мм 300 Storage temperature, С Operating temperature, С Maximum relative humidity, % 95 Dimensions, мм 71 х 49 х 28 Weight, g 40 Box material Plastic 15

16 Manufactured by LLC VK Electronics The product is made in accordance with the specifications LLC VK Electronics Office 3, NO 131, MIRA Prospect, MOSCOW, RUSSIA, Taxpayer Identification Number