Page 1 of 10 Cert. No. LRQ 0963008 ISO 9001 SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2 Description SPIR-TROL is a range of two-port single seat globe valves with cage retained seats conforming to EN standards. These valves are available in three body materials in sizes ranging from DN15 to DN100. When used in conjunction with a pneumatic or electric linear actuator they provide modulating control or on / off service. SPIR-TROL valve characteristic - options: LE Equal percentage (E) - Suitable for most modulating process control applications providing good control at all flowrates. LF Fast opening (F) - For on / off applications only. LL Linear (L) - Primarily for liquid flow control where the differential pressures across the valve is constant. Important note: Throughout this document, reference has been made to the standard LE control valve. With the exception of trim type, the LE, LF and LL control valves are identical. SPIR-TROL valve options: seals Standard Zero emissions and Stem sealing Bellows / graphite High temperature applications packing High temperature applications 431 stainless steel - standard Metal-to-metal 316L stainless steel Seating Up to 200 C: for class VI shut-off Soft seating Up to 250 C: PEEK for class VI shut-off Hard facing 316L stainless steel with Stellite 6 facing for more arduous applications Standard bonnet Bonnet type Extended bonnet for large pipe lagging or hot / cold applications Standard trim Trim Low noise cage Technical data Plug design Parabolic Leakage Metal-to-metal Class IV Soft seal Class VI Rangeability 50:1 Travel DN15 to DN50 20 mm DN65 to DN100 30 mm Typical flow characteristic curves 100 Fast opening Linear SPIR-TROL two-port control valves are compatible with the following actuators and positioners: Electric EL3500, EL5600 and EL7200 series Pneumatic PN1000 and PN9000 series PP5 (pneumatic) or EP5 (electropneumatic) ISP5 (intrinsically safe electropneumatic) Positioners SP200is, SP400 and SP500 (microprocessor based electropneumatic) SP300 (digital communications) Refer to the relevant Technical Information sheet for further details. Sizes and pipe connections Type Body material Connections Size range Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without notice. Copyright 2010 Flow % 50 0 0 50 Valve opening % Equal percentage LE31 Cast iron Screwed BSP DN15, DN20, DN25, DN32, DN40 and DN50 LE33 Cast iron Flanged PN16, LE43 Carbon steel DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80 and DN100 JIS 10 and KS 10 LE63 Stainless steel Note: The PN16 flange for the DN65 LE33 has 4 bolt holes as standard; 8 bolt holes are available on request. The PN16 flange for the DN65 LE43 and LE63 has 8 bolt holes as standard; 4 bolt holes are available on request. 100
Page 2 of 10 Materials Type No. Part Material LE31 LE33 1 Body SG iron BS EN-GLS-400-18u-LT 2 Bonnet SG iron EN-GLS-400-18u-LT 2a Bonnet extension Cast steel BS EN 10213 GP240GH+N (1.0619N) 2b Bellows Stainless steel 3 Stem lock-nut Stainless steel LE43 1 Body Carbon steel BS EN 10213 GP240GH+N (1.0619N) 2 Bonnet DN15 to DN50 Carbon steel EN 10222-2 P305GH 1.0436 DN65 to DN100 Carbon steel BS EN 10213 GP240GH+N (1.0619N) 2a Bonnet extension Carbon steel BS EN 10213 GP240GH+N (1.0619N) 2b Bellows Stainless steel 3 Stem lock-nut Stainless steel 1 Body Stainless steel DIN GX5 CrNiMO 19-11-2 1.4408 2 Bonnet Stainless steel DIN GX5 CrNiMO 19-11-2 1.4408 LE63 2a Bonnet extension Stainless steel DIN GX5 CrNiMO 19-11-2 1.4408 2b Bellows Stainless steel 3 Stem lock-nut Stainless steel 2c Extended bonnet Stainless steel ISI 316L 4 Bonnet gasket Reinforced exfoliated graphite 5 Seat retainer Stainless steel 316L 6 Valve seat ring Stainless steel 7 Seat gasket Reinforced exfoliated graphite 8 Valve plug and stem Stainless steel 9 * Lower stem guide Glass filled 10 Lower stem wiper 11 * Packing guard washer Stainless steel 316L 12 * Spring Stainless steel ll 13 Packing spacer Stainless steel 316L versions 14 * Chevron packing set using 15 * Outer 'O' ring Viton B 16 * Upper stem guide Glass filled seals 17 * Inner 'O' ring Viton 18 Gland nut Stainless steel 19 Scraper ring 20 ctuator clamp nut Plated carbon steel 22 Bonnet extension gasket Reinforced exfoliated graphite 23 Top plate (used on bonnet extension only) Stainless steel 316L 24 Lower spindle bearing housing Stainless steel 316L 25 Lower spindle bearing Stellite 6 26 Spindle lock and anti-rotation nut Stainless steel 316L LE3_ and LE4_ Steel DIN 933618.8 27 Set screws LE6_ Stainless steel DIN ISO 3506 2-70 Not shown * packing 9 16 Lower and upper stem guide Stellite 6 High 14 Grafoil packing rings temperature 11 packing 12 15 Not used 17 19 SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 3 of 10 3 3 19 18 19 18 20 15 14 8 17 16 27 9 14 13 12 11 10 9 2 4 16 Bonnet with graphite packing 1 6 7 5 LE valve with packing 14 LE valve with extended bonnet (E) 2a 2b 2c Extended bonnet (E) 22 LE valve with bellows seal (D) SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 4 of 10 Pressure/ temperature limits LE31 LE33 (Cast iron) LE31B LE33B Temperature C 300 250 200 150 100 50 0-10 Steam saturation curve 0 2 4 6 8 10 12 14 16 Pressure bar g Please note - Bellows sealed valves (Option D) are limited to -. LE43 LE43B (Carbon steel) Temperature C 400 300 250 200 100 Steam saturation 0 curve -10 0 2 4 6 8 10 12 14 16 Pressure bar g Please note - Bellows sealed valves (Option D) are limited to -. LE63 LE63B (Stainless steel) Note: The product must not be used in this region. High temperature graphite packing is required for use in this region. Body design conditions Temperature C 400 300 250 200 100 Steam saturation 0 curve -28-50 0 2 4 6 8 10 12 14.6 16 Pressure bar g Please note - Bellows sealed valves (Option D) are limited to -. Where the process fluid temperature is sub-zero and the ambient temperature is below +5 C, the external moving parts of the valve and actuator must be heat traced to maintain normal operation. LE31 16 bar g @ 120 C Maximum design pressure LE33 16 bar g @ 120 C LE43 16 bar g @ 50 C LE63 14.6 bar g @ 50 C LE31 300 C Maximum design temperature LE33 300 C LE43 400 C LE63 400 C LE31-10 C Minimum design temperature LE33-10 C LE43-10 C LE63-50 C Standard packing chevron 250 C soft seat (G) 200 C PEEK soft seat (K) 250 C Maximum operating temperature High temperature packing (H) 400 C Extended bonnet (E) with chevron 250 C Extended bonnet (E) with graphite packing 400 C Bellows (D) 300 C Minimum operating temperature LE31-10 C LE33-10 C Note: For lower operating temperatures LE43-10 C consult Spirax Sarco. packing -28 C LE63 packing -50 C Maximum differential pressures: See relevant actuator Technical Information sheet Maximum cold hydraulic test pressure of: LE31 24 bar g Warning: If the valve is fitted with a LE33 24 bar g bellows it must be removed if hydraulic LE43 24 bar g testing is to be done. LE63 24 bar g PN16 SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 5 of 10 Kvs values Size Nominal size DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 Travel 20 mm 30 mm Equal % 4.0 6.3 10.0 16.0 25.0 36 63 100 160 Full port Linear 4.0 6.3 10.0 16.0 25.0 36 63 100 160 Fast opening 4.0 6.3 10.0 18.0 28.0 50 85 117 180 Standard trims Reductions Trim 1 Trim 2 Trim 3 Equal % 2.5 4.0 6.3 10.0 16.0 25 36 63 100 Linear 2.5 4.0 6.3 10.0 16.0 25 36 63 100 Equal % 1.6 2.5 4.0 6.3 10.0 16 25 36 63 Linear 1.6 2.5 4.0 6.3 10.0 16 25 36 63 Equal % 1.0 1.6 2.5 4.0 6.3 10 16 25 36 Linear 1.0 1.6 2.5 4.0 6.3 10 16 25 36 Trim 4 Equal % 0.4 1.0 1.6 - - - - - - Linear 0.4 1.0 1.6 - - - - - - Micro flute 0.5 0.5 0.5 - - - - - - Linear 0.2 0.2 0.2 - - - - - - 0.1 0.1 0.1 - - - - - - Travel 20 mm 30 mm Low noise trim Full port 4.0 6.0 8.0 17 20 27 55 63 90 Reduced trim 1 Linear 3.5 5.0 6.0 12 13 15 35 40 60 Reduced trim 2 Linear 3.0 4.0 4.5 7 7 7 30 33 40 SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 6 of 10 Dimensions for the SPIR-TROL (approximate) in mm 1 B C C1 C2 D E Screwed Flanged* Screwed Screwed Flanged Extended Bellows Thread Valve BSP PN16 BSP BSP PN16 bonnet** sealed size JIS 10 JIS 10 bonnet KS 10 KS 10 DN15 130 130 40 103 103 237 237 69 DN20 155 150 45 103 103 237 237 69 DN25 160 160 50 103 103 237 237 69 M8 DN32 185 180 60 132 132 267 267 69 DN40 205 200 65 132 132 267 267 69 DN50 230 230 80 127 127 267 267 69 DN65-290 - - 201 359 368 81 DN80-310 - - 201 359 368 81 M12 DN100-350 - - 216 375 381 81 * Note: The PN16 flange for the DN65 LE33 has 4 bolt holes as standard; 8 bolt holes are available on request. The PN16 flange for the DN65 LE43 and LE63 has 8 bolt holes as standard; 4 bolt holes are available on request. ** Note See item 2c, page 3 for actual outline view of extended bonnet. E D E E D D C2 C C1 B Screwed version 1 Flanged version Bellows sealed or extended bonnet version Weights for the SPIR-TROL (approximate) in kg Bellows and Valve size LE31 LE33 LE43 LE63 extended bonnet DN15 4.0 5.0 5.0 5.0 4.5 DN20 5.0 6.0 6.0 6.0 4.5 DN25 5.5 6.5 6.5 6.5 4.5 DN32 9.0 10.0 10.0 10.0 5.5 DN40 10.0 12.8 12.8 12.8 5.5 DN50 11.0 15.0 15.0 15.0 5.5 DN65-32.0 32.0 32.0 9.5 DN80-36.0 36.0 36.0 9.5 DN100-53.0 53.0 53.0 13.0 SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 7 of 10 Dimensions / weights for the PN actuator range (approximate) in mm and kg ctuator range F G H J ctuator Weight With handwheel PN1500 and PN2500 405 1 114 - - 55 - PN1600 and PN2600 465 1 116 - - 70 - PN9100E and variants 275 170 55 225 6 + 5.86 PN9100R and variants 275 170 140 225 6 + 2.50 PN9200E and variants 300 300 55 225 17 + 7.20 PN9200R and variants 300 300 140 225 17 + 3.77 PN9320E and variants 325 390 65 350 27 + 7.20 PN9320R and variants 325 390 150 350 27 + 3.77 PN9330E and variants 335 390 65 350 27 + 7.20 PN9330R and variants 335 390 150 350 27 + 3.77 F J H ctuator G Dimensions / weights for the EL actuator range (approximate) in mm and kg ctuator range F G Weight EL3500 135 x 161 242 1.3 EL3500 SE 135 x 161 284 2.4 EL3500 SR 135 x 161 284 2.4 EL560_ 177 460 4.5 EL561_ 177 460 4.8 EL562_ 177 460 5.2 EL563_ 177 506 7.0 EL564_ 225 569 10.0 EL565_ 227 807 20.0 EL506_ 162 445 8.7 EL7200 series 100 471 3.0 SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 8 of 10 Spare parts SPIR-TROL The spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares. Note: When placing an order for spare parts please specify clearly the full product description as found on the label of the valve body, as this will ensure that the correct spare parts are supplied. vailable spares - LE, LF and LL ctuator clamping nut Gasket set (Non-bellows sealed) chevrons Stem seal kits C packing to conversion kit * Equal percentage trim (No gaskets supplied) Plug stem Fast opening trim and seat kit (No gaskets supplied) Linear trim (No gaskets supplied) or PEEK soft seat seal * Specify if reduced trim. B, G C2 C1 D, E D1, E D2, E H C1 C2 C D1 D2 How to order spares lways order spares by using the description given in the column headed 'vailable spares', and state the size and type of valve including the date code of the product. D Example: 1 - stem seal kit for a Spirax Sarco DN25 SPIR-TROL two-port LE43 PTSUSS.2 K vs 10 control valve. Soft seat arrangement B How to fit spares Full fitting instructions are given in the Installation and Maintenance Instructions supplied with the spare. H E G SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 9 of 10 Spare parts SPIR-TROL with bellows seal (D) The spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares. Note: When placing an order for spare parts please specify clearly the date code (found on the label of the valve body), this will ensure that the correct spare parts are supplied. C vailable spares - LE_B, LF_B and LL_B ctuator clamping nut Gasket set (Bellows sealed) Stem seal kits chevrons * Equal percentage trim (No gaskets supplied) Plug stem Fast opening trim and seat kit (No gaskets supplied) Linear trim (No gaskets supplied) Bellows seal assembly or PEEK soft seat seal * Specify if reduced trim. B, G C D3, E D4, E D5, E F H How to order spares lways order spares by using the description given in the column headed 'vailable spares', and state the size and type of valve including the date code of the product. Example: 1 - stem seal kit for a Spirax Sarco DN25 SPIR-TROL two-port LE43B TSUSS.2 K vs 10 control valve. How to fit spares Full fitting instructions are given in the Installation and Maintenance Instructions supplied with the spare. F D4 D5 Soft seat arrangement D3 B H E G SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 10 of 10 SPIR-TROL selection guide: Valve size Valve series DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80 and DN100 L = L series 2-port control valve DN25 L Valve characteristic Flow direction Body material Connections Stem sealing Seating Type of trim Trim balancing Bonnet type Bolting E = Equal percentage F = Fast opening L = Linear T = Flow over plug (not available for low noise trim) Blank = Flow under plug 3 = Cast iron 4 = Carbon steel 6 = Stainless steel 1 = Screwed 3 = Flanged P = D = Bellows / seals H = T = 431 stainless steel G = soft seat K = PEEK S = 316L stainless steel W = 316L with stellite 6 facing S = Standard trim P = Low noise cage U = Unbalanced S = Standard E = Extended (not available if bellows seal selected) S = Standard E 4 3 P T S U S S Series 2 =.2.2 K vs To be specified Kvs 10 Connection type To be specified Please note: The PN16 flange for the DN65 LE33 has 4 bolt holes as standard; 8 bolt holes are available on request. The PN16 flange for the DN65 LE43 and LE63 has 8 bolt holes as standard; 4 bolt holes are available on request. Flanged PN16 Selection example: DN25 - L E 4 3 P T S U S S.2 - Kvs 10 - Flanged PN16 How to order Example: 1 off Spirax Sarco DN25 SPIR-TROL LE43PTSUSS.2 Kvs 10 two-port control valve having flanged PN16 connections. SPIR-TROL DN15 to DN100 LE, LF and LL Two-port Control Valves TI-P303-11 CH Issue 2
Page 1 of 11 MNGEMENT SYSTEMS Cert. No. LRQ 0963008 ISO 9001 SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2 Description SPIR-TROL is a range of two-port single seat globe valves with cage retained seats conforming to EN standard. These valves are available in three body materials in sizes ranging from DN15 to DN100. When used in conjunction with a pneumatic or electric linear actuator they provide modulating control or on / off service. SPIR-TROL valve characteristic - options: KE Equal percentage (E) - Suitable for most modulating process control applications providing good control at all flowrates. KF Fast opening (F) - For on / off applications only. KL Linear (L) - Primarily for liquid flow control where the differential pressures across the valve is constant. Important note: Throughout this document, reference has been made to the standard KE control valve. With the exception of trim type, the KE, KF and KL control valves are identical. SPIR-TROL valve options: chevron seals Standard Bellows / (B) Suitable for thermal fluids Stem sealing Bellows / graphite (C) Suitable for thermal fluids Bellows / graphite Zero emissions and high temperature secondary seals (D) applications packing High temperature applications Metal-to-metal 431 stainless steel - standard 316L stainless steel Seating Up to 200 C - for Class VI shut-off Soft seating Up to 250 C - for Class VI shut-off Hard facing 316L stainless steel with Stellite 6 facing - for more arduous applications Bonnet Standard bonnet type Extended bonnet for large pipe lagging or hot / cold applications Trim Standard trim Low noise cage SPIR-TROL two-port control valves are compatible with the following actuators and positioners: Electric EL3500, EL5600 and EL7200 series Pneumatic PN1000 and PN9000 series PP5 (pneumatic) or EP5 (electropneumatic) ISP5 (intrinsically safe electropneumatic) Positioners SP200is, SP400, and SP500 (microprocessor based electropneumatic) SP300 (digital communications) Refer to the relevant Technical Information sheet for further details. Sizes and pipe connections Technical data Plug design Parabolic Leakage Metal-to-metal Class IV Soft seal Class VI Rangeability 50:1 Travel DN15 to DN50 20 mm DN65 to DN100 30 mm Typical flow characteristic curves Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without notice. Copyright 2010 Flow % 100 50 0 0 Fast opening 50 Valve opening % Linear Equal percentage Type Body material Connections Size range KE43 Cast steel Flanged PN25, PN40, JIS 20 and KS 20 DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80 and DN100 KE61 Stainless steel Screwed BSP DN15, DN20, DN25, DN32, DN40 and DN50 KE63 Stainless steel Flanged PN25, PN40, JIS 20 and KS 20 DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80 and DN100 KE71 SG iron Screwed BSP DN15, DN20, DN25, DN32, DN40 and DN50 KE73 SG iron Flanged PN16, PN25, JIS 10 and KS 10 DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80 and DN100 Note: The PN16 flanges for the DN65 KE73 sizes have 4 bolt holes as standard; 8 bolt holes are available on request. 100
Page 2 of 11 Materials Type No. Part Material KE43 KE61 KE63 KE71 KE73 1 Body Cast steel BS EN 10213 GP240GH+N (1.0619N) 2 Bonnet DN15 to DN50 Forged steel EN 10222-2 P305GH 1.0436 DN65 to DN100 Cast steel BS EN 10213 GP240GH+N (1.0619N) 2a Bonnet extension Cast steel BS EN 10213 GP240GH+N (1.0619N) 2b Bellows Stainless steel 3 Stem lock-nut Stainless steel 1 Body Stainless steel DIN GX5 CrNiMO 19-11-2 1.4408 2 Bonnet Stainless steel DIN GX5 CrNiMO 19-11-2 1.4408 2a Bonnet extension Stainless steel DIN GX5 CrNiMO 19-11-2 1.4408 2b Bellows Stainless steel 3 Stem lock-nut Stainless steel 1 Body SG iron EN-GJS-400-18u-LT 2 Bonnet SG iron EN-GJS-400-18u-LT 2a Bonnet extension Cast steel BS EN 10213 GP240GH+N (1.0619N) 2b Bellows Stainless steel 3 Stem lock-nut Stainless steel 2c Extended bonnet Stainless steel ISI 316L 4 Bonnet gasket Reinforced exfoliated graphite 5 Seat retainer Stainless steel 316L 6 Valve seat ring Stainless steel 7 Seat gasket Reinforced exfoliated graphite 8 Valve plug and stem Stainless steel 9 * Lower stem guide Glass filled 10 Lower stem wiper 11 * Packing guard washer Stainless steel 316L 12 * Spring Stainless steel 13 Packing spacer Stainless steel 316L 14 * Chevron packing set ll 15 * Outer 'O' ring Viton B versions 16 * Upper stem guide Glass filled using 17 * Inner 'O' ring Viton 18 Gland nut Stainless steel seals 19 Scraper ring 20 ctuator clamp nut Plated carbon steel 21 Bellows assembly Stainless steel ISI 316Ti + 316L 22 Bonnet extension gasket Reinforced exfoliated graphite 23 Top plate (used on bonnet extension only) Stainless steel 316L 24 Lower spindle bearing housing Stainless steel 316L 25 Lower spindle bearing Stellite 6 or stainless steel for KE - 43171/73 26 Spindle lock and anti-rotation nut Stainless steel 316L Standard KE4_ and KE7_ Steel BS 3692 Gr. 8 27 bonnet nuts KE6_ Stainless steel DIN ISO 3506 2 70 High temperature KE4_ and KE7_ Stainless steel DIN ISO 3506 2 70 bonnet nuts KE6_ Stainless steel DIN ISO 3506 2 70 Standard KE4_ and KE7_ Steel BS 3692 Gr. 8.8 28 bonnet studs KE6_ Stainless steel DIN ISO 3506 2 70 High temperature KE4_ and KE7_ Steel DIN ISO 3506 2 70 bonnet studs KE6_ Steel DIN ISO 3506 2 70 Not Shown * packing 9 16 Upper and lower stem guide Stellite 6 14 Grafoil packing rings High temperature 11 packing 12 15 Not used 17 19 SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 3 of 11 KE valve with graphite packing KE valve with extended bonnet (E) 3 19 18 DN15 - DN100 KE with bellows seal (B) and (C) 9 14 2c Extended bonnet (E) 16 KE valve with packing 3 18 20 15 28 14 13 12 11 10 9 4 19 8 17 16 27 2 14 2a 2b 1 6 7 5 22 KE valve with bellows seal (D) SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 4 of 11 Pressure/ temperature limits - Valve body Notes: KE43 (Cast steel) KE61 KE63 (Stainless steel) KE71 KE73 (SG iron) The product must not be used in this region. High temperature packing is required for use in this region. High temperature bolting and packing is required for use in this region. 1. Where the process fluid temperature is sub-zero and the ambient temperature is below +5 C, the external moving parts of the valve and actuator must be heat traced to maintain normal operation. 2. When selecting a valve with a bellows sealed bonnet, the pressure / temperature limits of the bellows must be read in conjunction with the valve pressure / temperature limits shown below. 400 350 300 250 200 Temperature C Temperature C Temperature C 100 0-10 0 400 350 300 200 100 0-28 -50 0 350 300 250 200 100 0-10 Pressure / temperature limits - Bellows 10 20 30 40 Pressure bar g 10 20 30 36.4 40 Pressure bar g Steam saturation curve 0 5 10 15 20 25 Pressure bar g Note: When selecting a valve with a bellows sealed bonnet, the pressure / temperature limits of the bellows must be read in conjunction with the valve pressure / temperature limits shown above. 300 250 200 Bellows B 150 Steam 100 saturation 50 curve 0 0 5 10 15 20 25 Pressure bar g 400 Bellows C Bellows D Temperature C Temperature C Temperature C 300 200 Steam 100 saturation curve 0 0 5 10 15 20 25 Pressure bar g 300 250 200 150 100 50 0 Steam saturation curve Steam saturation curve Steam saturation curve 0 2 4 6 8 10 12 14 16 Pressure bar g SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 5 of 11 Pressure/ temperature limits KE4_ PN40 Body design conditions KE6_ PN40 KE7_ PN25 KE4_ 40 bar g @ 50 C Maximum design pressure KE6_ 36.4 bar g @ 50 C KE7_ 25 bar g @ 120 C KE4_ 400 C Maximum design temperature KE6_ 400 C KE7_ 350 C KE4-10 C Minimum design temperature KE6_ -50 C KE7_ -10 C Standard packing chevron 250 C soft seat (G) 200 C PEEK soft seat (K) 250 C Maximum operating temperature High temperature packing (H) 400 C Extended bonnet (E) with chevron 250 C Extended bonnet (E) with graphite packing 400 C Bellows (See bellows pressure / temperature rating on page 4) 400 C KE4-10 C Minimum operating temperature packing -28 C KE6_ Note: For lower operating temperatures packing -50 C consult Spirax Sarco. KE7_ -10 C Maximum differential pressures: See relevant actuator Technical Information sheet Maximum cold hydraulic test pressure of: KE4_ 60 bar g Warning: If the valve is fitted with a bellows it must be removed if hydraulic KE6_ 60 bar g testing is to be done. KE7_ 38 bar g Kvs values Nominal size Size DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 Travel 20 mm 30 mm Equal % 4 6.3 10 16 25 36 63 100 160 Full port Reduced trim 1 Linear 4 6.3 10 16 25 36 63 100 160 Fast opening 4 6.3 10 18 28 50 85 117 180 Equal % 2.5 4 6.3 10 16 25 36 63 100 Linear 2.5 4 6.3 10 16 25 36 63 100 Standard Reduced trim 2 Equal % 1.6 2.5 4 6.3 10 16 25 36 63 trims Linear 1.6 2.5 4 6.3 10 16 25 36 63 Reduced trim 3 Reduced trim 4 Reduced trim 5 Equal % 1.0 1.6 2.5 4 6.3 10 16 25 36 Linear 1.0 1.6 2.5 4 6.3 10 16 25 36 Equal % - 1.0 1.6 - - - - - - Linear - 1.0 1.6 - - - - - - Equal % - - 1.0 - - - - - - Linear - - 1.0 - - - - - - Micro flute - 0.5 0.5 - - - - - - 0.2 0.2 0.2 - - - - - - 0.1 0.1 0.1 - - - - - - Travel 20 mm 30 mm Low noise trim Full port 4 6 8 17 20 27 55 63 90 Reduced trim 1 Linear 3.5 5 6 12 13 15 35 40 60 Reduced trim 2 Linear 3 4 4.5 7 7 7 30 33 40 SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 6 of 11 Dimensions for the SPIR-TROL (approximate) in mm 1 B C C1 C2 D E Screwed Flanged* Screwed Screwed Flanged Extended Bellows Thread Valve BSP PN16, PN25 and PN40 BSP BSP PN25 and PN40 bonnet sealed size JIS 10 JIS 20 bonnet KS 10 KS 20 DN15 130 130 40 103 103 237 237 69 DN20 155 150 45 103 103 237 237 69 DN25 160 160 50 103 103 237 237 69 DN32 185 180 60 132 132 267 267 69 M8 DN40 205 200 65 132 132 267 267 69 DN50 230 230 80 127 127 267 267 69 DN65-290 - - 201 359 368 81 DN80-310 - - 201 359 368 81 M12 DN100-350 - - 216 375 381 81 Note: The PN16 flanges for the DN65 KE73 sizes have 4 bolt holes as standard; 8 bolt holes are available on request. E D E E D D C2 C C1 B Screwed version 1 Flanged version Bellows sealed or extended bonnet version Weights for the SPIR-TROL (approximate) in kg dditional bellows Valve size KE43 KE61 KE63 KE71 KE73 and extended bonnet DN15 6.0 4.5 5.5 4.5 5.5 4.5 DN20 6.8 5.5 6.8 5.5 6.8 4.5 DN25 7.0 6.0 7.0 6.0 7.0 4.5 DN32 13.5 11.5 13.5 11.5 13.5 5.5 DN40 14.0 12.0 14.0 12.0 14.0 5.5 DN50 17.0 13.0 17.0 13.0 17.0 5.5 DN65 35.0-35.0-35.0 10.0 DN80 40.0-40.0-40.0 10.0 DN100 54.0-54.0-54.0 13.0 SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 7 of 11 Dimensions / weights for the PN actuator range (approximate) in mm and kg ctuator range F G H J ctuator Weight With handwheel PN1500 and PN2500 405 1 114 - - 55 - PN1600 and PN2600 465 1 116 - - 70 - PN9100E and variants 275 170 55 225 6 + 5.86 PN9100R and variants 275 170 140 225 6 + 2.50 PN9200E and variants 300 300 55 225 17 + 7.20 PN9200R and variants 300 300 140 225 17 + 3.77 PN9320E and variants 325 390 65 350 27 + 7.20 PN9320R and variants 325 390 150 350 27 + 3.77 PN9330E and variants 335 390 65 350 27 + 7.20 PN9330R and variants 335 390 150 350 27 + 3.77 F J H ctuator G Dimensions / weights for the EL actuator range (approximate) in mm and kg ctuator range F G Weight EL3500 135 x 161 242 1.3 EL3500 SE 135 x 161 284 2.4 EL3500 SR 135 x 161 284 2.4 EL560_ 177 460 4.5 EL561_ 177 460 4.8 EL562_ 177 460 5.2 EL563_ 177 506 7.0 EL564_ 225 569 10.0 EL565_ 227 807 20.0 EL506_ 162 445 8.7 EL7200 series 100 471 3.0 SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 8 of 11 Spare parts SPIR-TROL The spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares. Note: When placing an order for spare parts please specify clearly the full product description as found on the label of the valve body, as this will ensure that the correct spare parts are supplied. vailable spares - KE, KF and KL ctuator clamping nut Gasket set (Non-bellows sealed) B, G Stem seal chevrons C kits to conversion kit C1 packing C2 * Equal percentage trim (No gaskets supplied) D, E Plug stem Fast opening trim and seat kit (No gaskets supplied) D1, E Linear trim (No gaskets supplied) D2, E or PEEK Soft seat seal H * Specify if reduced trim. C1 C2 C D1 D2 How to order spares lways order spares by using the description given in the column headed 'vailable spares', and state the size and type of valve including the full product description of the product. D Example: 1 - stem seal kit for a Spirax Sarco DN25 SPIR-TROL two-port KE43 PTSUSS.2 Kvs 10 control valve. How to fit spares Full fitting instructions are given in the Installation and Maintenance Instructions supplied with the spare. Soft seat arrangement B H E G SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 9 of 11 Spare parts SPIR-TROL with bellows seal (Type B and C) DN15 to DN100 The spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares. Note: When placing an order for spare parts please specify clearly the full product description as found on the label of the valve body, as this will ensure that the correct spare parts are supplied. vailable spares - K and L series C1 C2 C ctuator clamping nut Gasket set (Bellows sealed) B, G Stem seal chevrons C kits to conversion kit C1 packing C2 * Equal percentage trim (No gaskets supplied) D3, E Plug stem Fast opening trim and seat kit (No gaskets supplied) D4, E Linear trim (No gaskets supplied) D5, E Bellow seal assembly F soft seal H * Specify if reduced trim. How to order spares lways order spares by using the description given in the column headed 'vailable spares', and state the size and type of valve including the full product description of the product. B B F Example: 1 - stem seal kit for a Spirax Sarco DN25 SPIR-TROL two-port KE43B TSUSS.2 Kvs 10 control valve. How to fit spares Full fitting instructions are given in the Installation and Maintenance Instructions supplied with the spare. B D4 D5 Soft seat arrangement D3 B H E G SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 10 of 11 Spare parts SPIR-TROL with bellows seal (Type D) The spare parts available are shown in solid outline. Parts drawn in broken line are not supplied as spares. Note: When placing an order for spare parts please specify clearly the full product description as found on the label of the valve body, as this will ensure that the correct spare parts are supplied. vailable spares - KE_B, KF_B and KL_B ctuator clamping nut Gasket set (Bellows sealed) Stem seal kit secondary seal and gasket set * Equal percentage trim (No gaskets supplied) Plug stem Fast opening trim and seat kit (No gaskets supplied) Linear trim (No gaskets supplied) Bellows seal assembly or PEEK soft seat seal * Specify if reduced trim. B, G C2 D3, E D4, E D5, E F H C2 How to order spares lways order spares by using the description given in the column headed 'vailable spares', and state the size and type of valve including the full product description of the product. Example: 1 - stem seal kit for a Spirax Sarco DN25 SPIR-TROL two-port KE43B TSUSS.2 K vs 10 control valve. How to fit spares Full fitting instructions are given in the Installation and Maintenance Instructions supplied with the spare. F D4 D5 D3 Soft seat arrangement B H E G SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 11 of 11 SPIR-TROL selection guide: Valve size Valve series Valve characteristic Flow direction Body material Connections Stem sealing Seating Type of trim Trim balancing Bonnet type Bolting DN15, DN20, DN25, DN32, DN40, DN50, DN65, DN80 and DN100 K = K series 2-port control valve E = Equal percentage F = Fast opening L = Linear T = Flow over plug (not available for low noise trim) Blank = Flow under plug 4 = Carbon steel 6 = Stainless steel 7 = SG iron 1 = Screwed 3 = Flanged P = B = Bellows / chevron seals C = Bellows / seals D = Bellows / secondary seals H = T = 431 stainless steel G = soft seat K = PEEK soft seat S = 316L stainless steel W = 316L with stellite 6 facing S = Standard trim P = Low noise cage U = Unbalanced S = Standard E = Extended (not available if bellows seal selected) S = Standard H = High temperature DN25 K E 4 3 P T S U S S Series 2 =.2.2 K vs To be specified Kvs 10 Connection type To be specified Please note: The PN16 flanges for the DN65 KE73 sizes have 4 bolt holes as standard; 8 bolt holes are available on request. Flanged PN40 Selection example: DN25 - K E 4 3 P T S U S S.2 - Kvs 10 - Flanged PN40 How to order Example: 1 off Spirax Sarco DN25 SPIR-TROL KE43PTSUSS.2 Kvs 10 two-port control valve having flanged PN40 connections. SPIR-TROL DN15 to DN100 KE, KF and KL Two-port Control Valves TI-P374-01 CH Issue 2
Page 1 of 8 TI-P357-30 CH Issue 8 PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves Description The PN9000 series actuators are a compact range of linear actuators that are available in 3 diaphragm sizes for matching the requirements of valves at various differential pressures. Each actuator is fitted with a mechanical travel indicator and incorporates a fully-rolling diaphragm, which provides good linearity over the operating stroke. vailable types Optional extra PN = Standard Suffix E = Spring-extend PNP = Electroless nickel plated Suffix R = Spring-retract Manual handwheel Stainless steel bolting Important note: Throughout this document, reference has been made to the PN actuator. Technical data Temperature range Maximum operating inlet pressure ir supply connection PN9100 PN9200 PN9300 PN9100-20 C to +110 C 6 bar g 6 bar g 4 bar g ¼" NPT 20 mm ctuator travel PN922_ and PN932_ 20 mm PN923_ and PN933_ 30 mm J Suffix H Suffix S J H G H F F F G PN9100 PN9200EH Dimensions / weights (approximate) in mm and kg G PN9337RH ctuator range F G H J Weight ctuator With handwheel PN9100E and variants 275 170 55 225 6 + 5.86 PN9100R and variants 275 170 140 225 6 + 2.5 PN9200E and variants 300 300 65 350 17 + 7.2 PN9200R and variants 300 300 152 350 17 + 3.77 PN9230E and variants 360 300 65 350 17 + 3.77 PN9230R and variants 360 300 152 350 17 + 3.77 PN9320E and variants 325 390 65 350 27 + 7.2 PN9320R and variants 325 390 152 350 27 + 3.77 PN9330E and variants 335 390 65 350 27 + 7.2 PN9330R and variants 335 390 152 350 27 + 3.7 PN9336E and variants 335 390 65 350 27 + 7.2 PN9336R and variants 335 390 152 350 27 + 3.77 PN9337E and variants 335 390 410 350 27 + 21 PN9337R and variants 335 390 410 350 27 + 21 Local regulations may restrict the use of this product to below the conditions quoted. In the interests of development and improvement of the product, we reserve the right to change the specification without notice. Copyright 2012
Page 2 of 8 Materials 2 5 28 22 and 23 3 4 7 31 30 6 16 32 21 24 8 9 29 17 18 15 19 and 20 25 10 12 26 and 27 1 13 and 14 11 No. Part Material 1 Yoke SG iron 2 Upper diaphragm housing Carbon steel (plated) 3 Diaphragm plate luminium 4 Diaphragm Reinforced NBR 5 Spring Spring steel 6 Spindle Stainless steel 7 Washer Carbon steel (plated) 8 Spacer Carbon steel (plated) 9 'O' ring Viton 10 Connector Stainless steel BS 970 431 S29 11 daptor Stainless steel BS 970 431 S29 PN9000 Carbon steel 12 Collar PNP9000 Stainless steel PN9000S Stainless steel 316L 13 Clamp front Stainless steel 14 Clamp rear Stainless steel 15 Scale Stainless steel 16 Vent plug Brass 17 Bearing /steel composite 18 Seal Polyurethane PN9000 Carbon steel (plated) 19 Pan head screw 20 Nyloc nut PNP9000 Stainless steel 2-70 PN9000S Stainless steel 2-70 21 Bolt Carbon steel (plated) Gr. 8.8 22 Hex. head screw (short) PN9000 Carbon steel (plated) Gr. 8.8 23 Hex. head screw (long) PNP9000 Stainless steel 2-70 24 Nut PN9000S Stainless steel 2-70 PN9000 Carbon steel (plated) 25 Lock-nut PNP9000 Stainless steel 2-70 PN9000S Stainless steel 2-70 26 27 Socket head screw Nut PN9000 Carbon steel (plated) Gr. 8.8 PNP9000 Stainless steel 2-70 PN9000S Stainless steel 2-70 28 Washer Carbon steel (plated) 29 Screw Carbon steel (plated) Gr. 8.8 30 Gasket Reinforced graphite 31 Lower diaphragm housing Carbon steel (plated) PN9000 Cast steel 32 Lifting eye PNP9000 Cast steel PN9000S Stainless steel 316L PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves TI-P357-30 CH Issue 7
Page 3 of 8 Spare parts The only spares available are clearly indicated below and are common for both spring-extend and spring-retract versions. vailable spares Stem seal kit 17, 18, 30 Diaphragm kit 4, 9 Travel indicator kit 15, 19, 20 Spring kit 5 Linkage kit (suitable for Mk1 and SPIR-TROL valves) 10, 13, 14, 26, 27 How to order spares lways order spares by using the description given in the column headed 'vailable spares' and state the actuator model. Example: 1 - Stem seal kit for a PN9120 pneumatic actuator. 5 4 30 9 17 18 15, 19 and 20 10 26 and 27 13 and 14 PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves TI-P357-30 CH Issue 8
Page 4 of 8 How to use the sizing data: The following tables supply guidance as to the sizing of the PN9000 when it is used on the SPIR-TROL K and L series valves. Two conditions are illustrated in tabular form: Class IV shut-off - Providing shut-off of the valve to the requirements of BS 5793-4 (IEC 60534-4) class IV. Class VI shut-off - Providing shut-off of the valve to the requirements of BS 5793-4 (IEC 60534-4) class VI. To select a suitable actuator: - Identify the column containing the valve and gland material selected. - Identify the maximum operating pressure condition, including any transient pressures likely to occur, within the selected column. - Read back to the left hand side of the table to identify the suitable actuator for the application. For conditions outside of those illustrated please contact Spirax Sarco. Maximum differential pressures for Class IV shut-off - PN9000E KE, LE, KE and LE with or stem seal (H) ctuator Spring range Maximum differential pressures bar DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9126E 1.0 2.0 28 13 20 9 12 4 10 3 2-1 - - - - - - - PN9123E 2.0 4.0 40 40 40 40 37 29 29 23 11 8 7 5 - - - - - - PN9220E 0.2 1.0 14-9 - 4-4 - - - - - - - - - - - PN9220E 0.4 1.2 40 33 36 24 22 14 18 12 6 3 3 2 - - - - - - PN9226E 1.0 2.0 40 40 40 40 40 40 40 40 24 21 16 14 - - - - - - PN9236E 1.0 2.0 - - - - - - - - - - - - 8 6 5 4 2 2 PN9223E 2.0 4.0 40 40 40 40 40 40 40 40 40 40 38 36 - - - - - - PN9233E 2.0 4.0 - - - - - - - - - - - - 20 18 12 11 7 7 PN9320E 0.2 1.0 40 32 35 24 22 14 17 11 6 3 3 1 - - - - - - PN9320E 0.4 1.2 40 40 40 40 40 40 40 38 17 15 12 10 - - - - - - PN9330E 0.4 1.2 - - - - - - - - - - - - 6 4 3 2 1 1 PN9336E 1.0 2.0 - - - - - - - - - - - - 22 20 12 11 7 6 PN9337E 2.5 3.5 - - - - - - - - - - - - 40 40 35 34 21 21 KE, LE, KE and LE with Bellows and or stem seal (H) ctuator Spring range Maximum differential pressures bar DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9226E 1.0 2.0 40 40 40 40 36 29 27 21 10 7 6 4 - - - - - - PN9236E 1.0 2.0 - - - - - - - - - - - - 5 5 3 3 2 2 PN9223E 2.0 4.0 40 40 40 40 40 40 40 40 40 37 27 25 - - - - - - PN9233E 2.0 4.0 - - - - - - - - - - - - 17 17 11 11 7 7 PN9320E 0.4 1.2 39 24 29 17 18 10 12 6 3 1 1 - - - - - - - PN9336E 1.0 2.0 - - - - - - - - - - - - 12 10 7 6 4 3 PN9337E 2.5 3.5 - - - - - - - - - - - - 40 40 30 28 18 17 PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves TI-P357-30 CH Issue 8
Page 5 of 8 Maximum differential pressures for Class VI shut-off - PN9000E ( (G) seat seal only) KE, LE, KE and LE with or stem seal (H) ctuator Spring range Maximum differential pressures bar DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9120E 0.2 1.0 4-3 - 2-2 - 1 - - - - - - - - - PN9120E 0.4 1.2 14-11 - 7-6 - 2-2 - - - - - - - PN9125E 0.4 2.0 14-11 - 7-6 - 2-2 - - - - - - - PN9126E 1.0 2.0 40 27 33 22 22 14 17 11 7 5 5 3 - - - - - - PN9123E 2.0 4.0 40 40 40 40 40 40 37 31 16 13 11 9 - - - - - - PN9220E 0.2 1.0 28 14 22 11 15 7 12 5 5 2 4 2 - - - - - - PN9220E 0.4 1.2 40 40 40 37 33 25 25 19 11 8 8 6 - - - - - - PN9230E 0.4 1.2 - - - - - - - - - - - - 4 2 3 2 2 1 PN9226E 1.0 2.0 40 40 40 40 40 40 40 40 29 26 21 19 - - - - - - PN9236E 1.0 2.0 - - - - - - - - - - - - 11 10 7 6 5 4 PN9223E 2.0 4.0 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9233E 2.0 4.0 - - - - - - - - - - - - 23 22 15 14 9 9 PN9320E 0.2 1.0 40 40 40 37 32 24 25 19 11 8 8 6 - - - - - - PN9320E 0.4 1.2 40 40 40 40 40 40 40 40 23 20 16 14 - - - - - - PN9330E 0.4 1.2 - - - - - - - - - - - - 9 7 6 4 4 3 PN9336E 1.0 2.0 - - - - - - - - - - - - 23 21 15 14 9 8 PN9337E 2.5 3.5 - - - - - - - - - - - - 40 40 37 36 23 23 KE, LE, KE and LE with Bellows and stem seal or stem seal (H) ctuator Spring range Maximum differential pressures bar DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9123E 2.0 4.0 16 1 12-8 - 6-3 - 2 - - - - - - - PN9226E 1.0 2.0 40 40 40 40 40 39 36 30 16 13 11 9 - - - - - - PN9236E 1.0 2.0 - - - - - - - - - - - - 5 5 3 3 2 2 PN9223E 2.0 4.0 40 40 40 40 40 40 40 40 40 40 33 31 - - - - - - PN9233E 2.0 4.0 - - - - - - - - - - - - 17 17 11 11 7 7 PN9320E 0.4 1.2 40 38 40 30 28 20 22 16 9 7 7 5 - - - - - - PN9330E 0.4 1.2 - - - - - - - - - - - - 1-1 - 1 - PN9336E 1.0 2.0 - - - - - - - - - - - - 16 14 10 9 6 6 PN9337E 2.5 3.5 - - - - - - - - - - - - 40 40 33 32 20 20 PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves TI-P357-30 CH Issue 8
Page 6 of 8 Maximum differential pressures for Class IV shut off - PN9000R KE, LE, KE and LE with or stem seal (H) Maximum differential pressures bar ctuator Spring range Maximum air pressure DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9120R 0.2 1.0 6 40 40 40 40 40 40 40 40 36 34 25 23 - - - - - - PN9120R 0.4 1.2 6 40 40 40 40 40 40 40 40 34 32 24 22 - - - - - - PN9125R 0.4-2.0 6 40 40 40 40 40 40 40 40 28 25 19 17 - - - - - - PN9126R 1.0 2.0 6 40 40 40 40 40 40 40 40 28 25 19 17 - - - - - - PN9123R 2.0 4.0 6 40 40 40 40 37 29 29 23 11 8 7 5 - - - - - - PN9220R 0.2 1.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9220R 0.4 1.2 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9230R 0.4 1.2 6 - - - - - - - - - - - - 40 40 34 33 21 20 PN9226R 1.0 2.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9236R 1.0 2.0 4 - - - - - - - - - - - - 40 40 28 27 17 16 PN9223R 2.0 4.0 6 40 40 40 40 40 40 40 40 40 40 38 36 - - - - - - PN9233R 2.0 4.0 6 - - - - - - - - - - - - 20 18 12 11 7 7 PN9320R 0.2 1.0 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9320R 0.4 1.2 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9330R 0.4 1.2 4 - - - - - - - - - - - - 40 40 39 38 24 23 PN9336R 1.0 2.0 4 - - - - - - - - - - - - 40 40 27 26 17 16 PN9337R 2.5 3.5 4 - - - - - - - - - - - - 8 6 5 3 2 2 KE, LE, KE and LE with Bellows and or stem seal (H) Maximum differential pressures bar ctuator Spring range Maximum air pressure DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9120R 0.2 1.0 6 40 40 40 40 40 40 40 40 22 19 15 13 - - - - - - PN9120R 0.4 1.2 6 40 40 40 40 40 40 40 40 20 18 14 12 - - - - - - PN9125R 0.4-2.0 6 40 40 40 40 40 40 36 30 13 11 9 7 - - - - - - PN9126R 1.0 2.0 6 40 40 40 40 40 40 36 30 13 11 9 7 - - - - - - PN9220R 0.2 1.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9220R 0.4 1.2 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9230R 0.4 1.2 6 - - - - - - - - - - - - 40 40 32 32 20 20 PN9226R 1.0 2.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9236R 1.0 2.0 4 - - - - - - - - - - - - 40 40 26 26 16 16 PN9223R 2.0 4.0 6 40 40 40 40 40 40 40 40 40 37 27 25 - - - - - - PN9233R 2.0 4.0 6 - - - - - - - - - - - - 17 17 11 11 7 7 PN9320R 0.2 1.0 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9320R 0.4 1.2 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9330R 0.4 1.2 4 - - - - - - - - - - - - 40 40 34 33 21 20 PN9336R 1.0 2.0 4 - - - - - - - - - - - - 35 34 22 21 13 12 PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves TI-P357-30 CH Issue 8
Page 7 of 8 Maximum differential pressures for Class VI shut-off - PN9000R ( (G) seat seal only) KE, LE, KE and LE with or stem seal (H) Maximum differential pressures bar ctuator Spring range Maximum air pressure DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9120R 0.2 1.0 6 40 40 40 40 40 40 40 40 40 39 29 28 - - - - - - PN9120R 0.4 1.2 6 40 40 40 40 40 40 40 40 40 37 28 26 - - - - - - PN9125R 0.4-2.0 6 40 40 40 40 40 40 40 40 33 30 23 21 - - - - - - PN9126R 1.0 2.0 6 40 40 40 40 40 40 40 40 33 30 23 21 - - - - - - PN9123R 2.0 4.0 6 40 40 40 40 40 40 37 31 16 13 11 9 - - - - - - PN9220R 0.2 1.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9220R 0.4 1.2 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9230R 0.4 1.2 6 - - - - - - - - - - - - 40 40 37 35 23 22 PN9226R 1.0 2.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9236R 1.0 2.0 4 - - - - - - - - - - - - 40 40 30 29 19 18 PN9223R 2.0 4.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9233R 2.0 4.0 6 - - - - - - - - - - - - 23 22 15 14 9 9 PN9320R 0.2 1.0 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9320R 0.4 1.2 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9330R 0.4 1.2 4 - - - - - - - - - - - - 40 40 40 40 26 25 PN9336R 1.0 2.0 4 - - - - - - - - - - - - 40 40 30 29 19 18 PN9337R 2.5 3.5 4 - - - - - - - - - - - - 11 9 7 6 4 4 KE, LE, KE and LE with Bellows and stem seal or stem seal (H) Maximum differential pressures bar ctuator Spring range Maximum air pressure DN15 DN20 DN25 DN32 DN40 DN50 DN65 DN80 DN100 PN9120R 0.2 1.0 6 40 40 40 40 40 40 40 40 28 25 20 18 - - - - - - PN9120R 0.4 1.2 6 40 40 40 40 40 40 40 40 26 24 19 17 - - - - - - PN9125R 0.4-2.0 6 40 40 40 40 40 40 40 39 20 17 14 12 - - - - - - PN9126R 1.0 2.0 6 40 40 40 40 40 40 40 39 20 17 14 12 - - - - - - PN9123R 2.0 4.0 6 16 1 12-8 - 6-3 - 2 - - - - - - - PN9220R 0.2 1.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9220R 0.4 1.2 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9230R 0.4 1.2 6 - - - - - - - - - - - - 40 40 32 32 20 20 PN9226R 1.0 2.0 6 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9236R 1.0 2.0 4 - - - - - - - - - - - - 40 40 26 26 16 16 PN9223R 2.0 4.0 6 40 40 40 40 40 40 40 40 40 40 33 31 - - - - - - PN9233R 2.0 4.0 6 - - - - - - - - - - - - 17 17 11 11 7 7 PN9320R 0.2 1.0 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9320R 0.4 1.2 4 40 40 40 40 40 40 40 40 40 40 40 40 - - - - - - PN9330R 0.4 1.2 4 - - - - - - - - - - - - 40 40 37 36 23 23 PN9336R 1.0 2.0 4 - - - - - - - - - - - - 39 38 25 24 16 15 PN9337R 2.5 3.5 4 - - - - - - - - - - - - 4 2 2 1 1 1 PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves TI-P357-30 CH Issue 8
Page 8 of 8 PN9000 series selection guide: Type PN = Polyester powder coated (standard) PNP = Electroless nickle plated PNP Series 9 = 9000 series 1 = 100 cm 2 9 ctuator size 2 = 340 cm 2 3 Valve travel Spring rating Spring action Manual override Stainless steel bolting 3 = 670 cm 2 2 = 20 mm 3 = 30 mm 0 = 0.2 to 1.0 bar (option for 0.4 to 1.2 bar) 3 = 2.0 to 4.0 bar 5 = 0.4 to 2.0 bar (PN9100 series only) 6 = 1.0 to 2.0 bar 7 = 2.5 to 3.5 bar (PN933_ series only E = Spring-extend R = Spring-retract H = Handwheel (optional) S = Stainless steel bolting (optional) 3 7 E How to order / selection example: 1 off Spirax Sarco PNP9337E pneumatic actuator. PN9000 Series Pneumatic ctuators for SPIR-TROL K and L Series Control Valves TI-P357-30 CH Issue 8