Chapter 19. The REDA gas can fits in the Original Equipment hard luggage on Touring models and takes 1 US fluid Gallon (almost 4 liters) of fuel

Chapter The REDA gas can fits in the Original Equipment hard luggage on Touring models and takes 1 US fluid Gallon (almost 4 liters) of fuel Chapter is all about gas tanks. Zodiac has always been a front runner when it comes to fuel tanks. We havetwo-piece gas tanks in steel, One-piece gas tanks in steel, One-piece gas tanks in aluminum, stock replacement gas tanks, gas tanks with increased fuel capacity, Custom style gas tanks. In short: any type of gas tank you could want. In this chapter you will also find everything else needed to go with your gas tank including all types of speedo, speedo brackets and speedo cables, fuel caps and fuel lines. New in this issue are the REDA gas can, the Fuel Tool and parts and accessories from Crime Scene Choppers and Cycle Kraft. TheFuel-Toolisaquick,safeandeasyway to transfer fuel from any 2001 and later fuel injected Twin Cam or Sportster to another bike and is also great to drain fuel tanks without any spilling Arlen Ness gas tank extensions for Touring models are available for both 97 thru 2007 and 2008 to present FLT Tour Glide, FLHT Electra Glide, FLHX Street Glide and FLTR Road Glide models THE FACTORY HAND-CAST GASCAPS Just in time to make it into the Bikers Book are these traditionally hand-cast brass or aluminum gas caps with steel weld-in bung from The Factory. 735497 Hand-cast brass gascaps 735498 Aluminum gascaps

Gas Tank 3.5 GALLON HAND SHIFT GAS TANK A reproduction of the long unavailable hand shift style 3.5 gallon (13,2 ltr) tank set as used on the 47 thru 65 Big Twin Harley-Davidson. This reproduction takes original rod type (ZPN 011136) shut-off valve, cam style gas caps (see gas cap section), cross over gas line (ZPN 012251) and is designed to accept the 47 thru 65 shifter guide. Measurement may slightly vary from OEM tank (style A). 011381 Hand Shift Gas Tank ORIGINAL STYLE FAT BOB TANK Reproductions of the classic Fat Bob gas tank. Mounting is made to OEM specifications for a perfect fit on stock Harley 4 Speed Big Twin frames thru 84 (except Softails).Also fits our Custom rigid and swing arm frames. Each tank is quality inspected and made to accept either the FX style dual instrument dash or the FL-FXWG style large speedo dash, for that Fat Bob look. Available in 3.5 gallon (13,2 ltr) and 5 gallon (18,9 ltr). Tank accepts OEM or after market gascaps and fuel valve. Cam lock style gas tanks (style A) 011303 3 1/2 Gallon tank set (OEM 61218-67A & 61426-67A) 011302 5 Gallon tank set (OEM 61211-67 & 61228-67A) Screw-In type gas tanks (style B) 011373 3 1/2 Gallon tank set (OEM 612-83 & 61425-83) 011374 5 Gallon tank set (OEM 61213-83 & 61229-83) Lockable Quick-Lock flush style gas tank with caps (style D) 011558 5 Gallon tank set, includes lockable gas caps 011549 Lockable gas cap set 3.5 GALLON HAND SHIFT GAS TANK Updated version of the hand shift style gas tank 3.5 gallon (13,2 ltr) as used on 47 thru 65 Big Twin models (ZPN 011381).This tank uses 75 and later style petcocks instead of the original rod type shutoff valve.will accept the correct cam-style gas caps and is designed to accept the stock shifter guide (style A). 011382 Hand Shift Gas Tank GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -002

Gas Tank 6 GALLON FAT BOB TANKS FOR 4 SPEED FRAMES This King Size Fat Bob tank holds 6 gallon (22,7 ltr) and fits the 4 Speed Big Twin frames thru 84 (except Softail models). Made on all new Zodiac tooling and therefore exclusively available from Zodiac. This large capacity tank does not look bulky. We kept the contours of the stock tank so it remains an integral part of the motorcycle. It's large capacity offers the extra mileage to those who want to go the distance. Available for cam lock caps or late type Screw-In gas caps.accept stock style dashes. Due to the slightly different contour with flexible tankpanel (not die-cast). 011316 Cam lock type gas tank (style A) 011318 Screw-In type gas tank (style B) FAT BAGGER 7 GALLON GAS TANKS FOR TOURING MODELS Stretched gas tanks that bolt straight on to the stock mountings and include a special rear mounting bracket to replace the stock one.tanks are approx. 18" (46 cm) wide and an impressive 25" (64 cm) long and take 7 Gallon (26.5 ltr) of fuel. Installation requires the seat to be customized or use of a custom seat. Tanks for carburetor equipped models are smooth top, those for EFI (Electronic Fuel Injection) come complete with a raw steel custom dash. The same dash but with a flawless chrome finish is available separately.tanks for EFI models take the Original Equipment fuel pump. All versions take the stock screwin style gas caps (Style B). 012906 Fits all 96 thru 2006 carburetor equipped FLH and FLT series Touring models 012908 Fits all 2003 thru 2007 EFI equipped FLH and FLT series Touring models 012907 Fits all 2008 EFI equipped FLH and FLT series Touring models 012909 Optional chrome dash for EFI models MUSTANG QUICKBOB GAS TANK FOR 4 SPEED FRAME Large capacity 4.5 gallon (17 ltr) one piece Fat Bob style tank. Designed to fit all stock 4 Speed Big Twin swing arm frames 72 thru 84 (except FXST) when using OEM mounting hardware. Also usable for Custom applications. Accepts Harley style petcock. Available for use with early style cam-lock gas caps or the later style Screw-In type gas cap as well as our latest "Quick Cam" Lockable flush mount gas caps. Flush mount caps are included with this tank. 011295 Cam lock type gas tank (style A) 011312 Screw-In type gas tank (style B) 011565 Quick Cam lockable flush mount type tank includes set of gas caps (style D) -003

Gas Tank FLAT-SIDE FAT BOB TANKS Our Fat Bob tank sets are a duplication of the late style "Flatside" tank sets.they fit FXST models 84 thru 99 and are available in a wide variety of tank caps such as OEM style cam lock gas cap and Screw-In bung and flush cap design. Flush caps are available as a Screw-In bung and our quick-lock style. Quick lock can also be bought with key operated lock. The latest addition is the small aluminum aircraft style gas cap set. These lockable Aero-style gas cap sets have a chrome plated finish and are also separately available.tanks are the best quality on the market. Can be used for crash repairs or any other Custom application.available in a 3.5 (13,2 ltr) and a 5 (18,9 ltr) gallon capacity. Accepts most FL, FXWG and FXST style dashes. Screw bung style tank sets (style B) 011184 Tank set 3.5 gallon (OEM 61218-85 & 61426-85) 011389 Tank set 5 gallon (OEM 61211-84A & 61228-84A) Lockable Screw-In type flush mount tank sets (style D) These flush caps make the lines of this tank much smoother than on the stock tanks (includes gas caps). 011557 5 Gallon Quick lock flush cap tank set 011549 Lockable gas cap set (style D) 5 Gallon tank set for Midi Aero-style gas caps, chrome plated aluminum gas cap set with locks is included (style E) 011731 Tank set 5 gallon with Midi Aero-style gas caps 011528 Replacement Aero gas cap set Midi (style E) 011526 Replacement Aero-style gas cap Midi vented (style E) 011527 Replacement Aero-style gas cap Midi non-vented (style E) "KING" 6 GALLON FLAT-SIDE FAT BOB TANK The extra large 6 gallon "King" Fat Bob tank was designed in such a way it does not change the overall appearance of your motorcycle.they went to great lengths to duplicate the contours of the stock tank, to retain the original Fat Bob looks. Once installed, the "King" Fat Bob looks like an integral piece of the motorcycle and not just an oversized bolt on accessory.this tank holds over 6 gallons (23 ltr) of fuel, offering you the extra mileage needed.the brackets and insides of the tank are made from extra heavy gauge, reinforced steel to carry the extra weight of the fuel. Unlike the competition's tanks, this tank has flowing lines without any flat spots and doesn't need excessive plaster before spraying. Fits all Softail models 84 thru 99.Accepts all large speedo style dashes.available with Screw-In type gas caps, lockable gas caps and our latest lockable Aero-style small aluminum gas caps with chrome plated finish. Gas caps are also separately available. 011338 Tank set for Screw-In style gas caps (style B) 011563 Tank set with Quick Cam lockable gas caps, caps included (style D) 011732 Tank set with Midi Aero-style chrome plated and lockable gas caps, caps included (style E) Replacement gas caps 011549 Lockable gas cap set (style D) 011528 Replacement Aero gas cap set Midi (style E) 011526 Replacement Aero-style gas cap Midi vented (style E) 011527 Replacement Aero-style gas cap Midi non-vented (style E) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -004

Gas Tank STRETCHED FLAT-SIDE TANKS FOR SOFTAIL MODELS These split stretched gas tanks will give your Softail that long, slippery stretched look associated with the top Custom bike builders. The stretched section is not a weld-on piece but an actual part of the tank. The exclusive stretched Zodiac tanks are the only one-piece steel tank available. Its design will give your bike smooth flowing lines and a very classy look. Due to the sleek design a narrow seat (like our Silhouette seats) must be used, stock seat may not fit. Fits all Softail models 84 thru 99.Available with Screw-In type gas caps, Quick Cam lockable flush or a set of our small chrome plated aluminum Aero-style gas caps. Gas caps are separately available. Stretched 2 piece gas tank with Screw-In type gas caps (style B) 011585 Stretched Slim Bob 4.1 gallon (15,5 ltr) 011584 Stretched Fat Bob 5.5 gallon (20,8 ltr) Stretched 2-piece gas tank with Quick Cam type gas caps, gas caps are included (style D) 011591 Stretched Slim Bob 5,3 gallon (20,1 ltr) 011590 Stretched Fat Bob 5,8 gallon (22 ltr) 011549 Lockable gas cap set (style D) Stretched 2-piece gas tank with Midi lockable aluminum Aero-style gas caps, gas caps are included (style E) 011733 Stretched Fat Bob 5,3 gallon (20,1 ltr) 011528 Replacement Aero gas cap set Midi (style E) 011526 Replacement Aero-style gas cap Midi vented (style E) 011527 Replacement Aero-style gas cap Midi non-vented (style E) 4" STRETCHED STEEL FLAT-SIDE GAS TANK FOR SOFTAILS These two piece stretched gas tanks will give an extra long, extra slippery stretched look. Tanks are made by welding a 2" extension to our stretched tanks making them in total 4" (10 cm) longer than the stock tank. The extra stretch provides that special slim look. The rear of the tank has a cut out to match with most narrow seats, such as our Silhouette seats. Fits Softail models 84 thru 99.Tanks are available in three different cap styles and two sizes, 4.2 gallon (15.9 ltr) and 5.4 gallon (20,4 ltr). Tank set for Screw-In type gas caps (style B) 011680 Stretched gas tank set, screw (4.2 gallon) 011615 Stretched gas tank set, screw (5.4 gallon) Tank set with Quick Cam, lockable flush mount type gas caps, gas caps included (style D) 011681 Stretched gas tank set, flush (4.2 gallon) 011633 Stretched gas tank set, flush (5.4 gallon) Tank set with Aero-style Midi aluminum lockable gas gaps with chrome plated finish, gas caps included (style E) 011734 Stretched gas tank set,aero (5.4 gallon) Tank set with Aero-style Midi aluminum lockable gas gaps with chrome plated finish, gas caps included (style E) 011549 Lockable gas cap set (style D) 011528 Replacement Aero gas cap set Midi (style E) 011526 Replacement Aero-style gas cap Midi vented (style E) 011527 Replacement Aero-style gas cap Midi non-vented (style E) -005

Gas Tank ONE PIECE STRETCHED SMOOTH TOP STEEL GAS TANK FOR SOFTAIL MODELS This one piece stretched gas tank will give your Softail the long, slippery stretched look associated with the top Custom bike builders. The stretched section is not a weld-on piece but an integral part of the tank.the exclusive Zodiac stretched tanks are the only one piece steel tank available. Its design will give your bike smooth, flowing lines and a very classy look. Stretched Softail tanks are available with dual and single screw type gas cap, dual or single, "Quick-Lock" lockable gas cap as well as a tank with a single cap aircraft style Aero gas gap and with the latest style Pop-Up gas cap in a paintable or chrome finish. Due to the sleek design a narrow seat (like our Silhouette seats) must be used, it can't be used with the stock seat. Fits Softail models 84 thru 99.Tanks hold approx. 4.2 gallon fuel (15,9 ltr). Gas tanks for use with Screw-In type gas caps. Caps not included (style B) 011675 Single cap stretched gas tank 011660 Dual cap stretched gas tank Gas tanks for use with Quick Cam lockable flush mount gas caps, gas cap(s) included (style D) 011677 Single cap stretched gas tank 011676 Dual cap stretched gas tank Gas tank for use with large chrome plated Aero-style lockable gas cap, gas cap included (style F) 011735 Single cap stretched gas tank Center fill gas tanks complete for use with pop-up gas cap, gas cap included (style G) 011856 With paintable Pop-Up gas cap 011857 With chrome Pop-Up gas cap CRUISE SPEED 2" STRETCH GAS TANK FOR EVOLUTION SOFTAIL STYLE FRAMES Like on the other Cruise Speed tanks no expense was spared in the construction and finish quality of these gas tanks.they are hand crafted from heavy gauge steel and feature joggle lap and lap joints through out, resulting in a super-strong gas tank without the worry of compromising the structural strength while providing a smooth surface finish. The joggle lap joints also allow the tunnel plate to be sunken below the bottom surface of the tank, making grinding of the welds unnecessary. Dependent on the application the tank is mounted to the frame using the two supplied weld-on frame brackets, or the bolt-on bracket and one of the weld-on frame brackets. Brackets feature a recessed rubber mounting system to isolate the tank from vibrations. Tank has 23.64" overall length, 20" long tunnel with a reduced width front. Holds approx. 4 Gallon (15,1 ltr) of fuel. Comes complete with mounting hardware and features 13/16" (22 mm) petcock outlet, breather tube and rear gas crossovers tapped for 1/8"-27 NPT unions. Available for use with pop-up style gas cap. Gas caps are not included but must be ordered separately. 930221 Chopper gas tank for pop-up style gas cap (Style G) 012100 Pop-up style gas cap, raw (style G) 012101 Pop-up style gas cap, chrome (style G) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -006

Gas Tank ONE PIECE 2" STRETCHED STEEL TANK WITH INDENTS Stunning stretched appearance of your motorcycle with this one piece 2" stretched tanks. No weld-on stretched sections, just one piece high quality steel with indents on both sides. Please note that the seat cutout at the stretched sections matches most narrow model seats, e.g. Silhouette. Fits stock 84 thru 99 Softail frames as well as most aftermarket Softail style frames.available for use with OEM style screwin gas cap or complete with Aero Style or gas cap. Must be used in combination with a 13/16" (22 mm) petcock.to allow easy installation, all mounting hardware and brackets are included. Fits 84 thru 99 Softail models, capacity 4.3 gallon (16.3 ltr) 012811 Tank for screw-in style cap (style B) 012813 Tank with Aero-style lockable cap (style F) ONE PIECE 2" STRETCHED STEEL GAS TANK FOR SOFTAIL MODELS WITH DASH MOUNT Stretched gas tanks will give your Softail the same long, slippery stretched look and flowing lines as found in our other one piece stretched tank but as an extra feature also includes a dash mount welded in place.the stretched section is not a weld on but is an integral part of the tank and has a seat pocket to match with most narrow seats, such as our Silhouette seats. Fits Softail models 84-99.Tank holds approx. 4.2 gallon (15,9 ltr) and is available with dual Screw-In type gas caps as well as dual Quick Cam lockable gas caps. 011625 Dual cap Screw-In type gas tank with dash mount (style B) 011628 Dual cap, Quick Cam lockable flush mount gas tank with dash mount, gas caps are included (style D) ONE PIECE 3" STRETCHED STEEL GAS TANK WITH AERO LOCKING GAS CAP FOR SOFTAILS THRU 99 This one-piece 3" stretched gas tank has a smooth top and includes a single midi aero locking gas cap.this tank gives your bike the same kind of styling as with the aluminum gas tanks, but at a much more economical price.the rear of the tank has a cut-out to match with most narrow seats.tank holds approx. 3.8 gallon (14,4 ltr) 011777 One piece 3" stretched gas tank with aero locking gas cap (style E) 011526 Replacement Aero-style gas cap Midi vented (style E) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -007

Gas Tank ONE PIECE 4" STRETCHED STEEL SMOOTH TOP GAS TANK FOR SOFTAILS These one piece stretched smooth top gas tanks will give your Softail the long, extra slippery stretched look and flowing lines which is very popular with today's top Custom bike builders.these tanks are made by welding a 2 inch extension to our stretched tanks making them in total 4 inch (10 cm) longer than stock.the extra stretch provides that special slim look.the rear of the tank has a cut out to match with most narrow seats, such as our Silhouette seats. Fits Softail models 84 thru 99. Tanks are available with four different cap styles and hold approx. 4.2 gallon of fuel (15,9 ltr). Tanks for Screw-In type gas caps (style B) 011622 Single cap stretched gas tank 011644 Dual cap stretched gas tank Tanks complete with Quick Cam lockable, flush mount type gas cap (style D) 011630 Single cap stretched gas tank 011629 Dual cap stretched gas tank Tank complete with large Aero-style chrome plated aluminum lockable gas cap (style F) 011736 Single cap gas tank with Aero-style gas cap Tanks with center fill Pop-Up gas cap (style G) 011858 With single paintable Pop-Up gas cap 011859 With single chrome Pop-Up gas cap GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT IS NOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. CUSTOM STYLE SMOOTH TOP TANKS FOR TWIN CAM SOFTAIL MODELS This Custom style smooth top gas tank drastically changes the looks of your Twin Cam Softail, it provides much smoother looks and creates the possibility to use one of our mini speedo's or mini information centers.tanks are made from steel and can be used with the stock seat. Tank comes complete with a center mounted billet aluminum Aerostyle lockable gas cap and holds approx. 5.1 gallon (,3 ltr) of fuel. Fits carburetor equipped Twin Cam Softail models 2000 to present 011804 Smooth top, complete with center mounted signal Aerostyle gas cap (style E) 2" STRETCHED CUSTOM STYLE SMOOTH TOP TANKS FOR CARBURETOR TWIN CAM SOFTAIL MODELS 2000 TO PRESENT One-piece stretched steel Custom gas tank with smooth top, gives your Softail a longer, stretched look.will work with most Custom seats and comes complete with center mount billet aluminum Aero-Style lockable gas cap (gas cap included). Fits carburetor equipped Twin Cam Softails 2000 up and holds approx. 5.1 gallon (22,7 ltr) of fuel. 011810 Smooth top gas tank with center mounted Aero-Style gas cap (style E) -008

Gas Tank CUSTOM STYLE TANKS WITH DASH MOUNT FOR SOFTAIL TWIN CAM MODELS Custom gas tanks with dash mount for Twin Cam models 2000 to present. Can be used with the stock or stock style seats. Made from heavy gauge steel for years of leak and trouble free riding. Tanks are available for use with OEM style Screw-In gas caps and the gauge equipped OEM left side cap, as well as a model with our Quick Cam lockable gas caps on both sides of the tank. Both styles are available for carburetor and EFI models.tanks take approx. 5.1 gallon (,3 ltr). Fits carburetor equipped Twin Cam Softail models 2000 to present 011813 Screw-In style gas caps, caps not included (style B) 011801 Quick Cam lockable gas caps, caps included (style D) 2" STRETCHED CUSTOM STYLE TANKS WITH DASH MOUNT FOR SOFTAIL TWIN CAM MODELS This one-piece stretched gas tank has a proper dash mount and will give your Softail longer, stretched look. This tank will change the appearance of your bike. Due to the stretch these tanks must be used with a Custom seat.tanks are available for use with OEM style Screw- In style gas caps on the right hand side and fuel gauge on the left side. For those who can do without this gauge we have a tank available that uses our Quick Cam lockable gas caps on both sides.tanks take approx. 5.1 gallon (.3 ltr) of fuel. Fits carburetor equipped Twin Cam Softail models 2000 to present 011814 Screw-In style gas cap, cap not included (style B) 011807 Quick Cam lockable gas caps, caps included (style D) Fits Fuel Injection equipped Twin Cam Softail models 2001 to present 011861 Screw-In style gas caps (style B) Fits Fuel Injection equipped Twin Cam Softail models 2001 to present 011864 Screw-In style gas cap, cap not included (style B) 011865 Quick Cam lockable gas caps, caps included (style D) -009

Gas Tank RUBBER MOUNT CUSTOM GAS TANK FOR FUEL INJECTED TWIN CAM SOFTAIL Steel custom style gas tank with cover to hide the stock fuel pump panel. Has two screw-in bungs for OEM or aftermarket gas caps. Comes with custom frame mount brackets that have to be welded to the frame. Features recessed bottom mounts with heavy duty rubber isolators. Tank has a 22 1/4" (56.5 cm) long and 2 1/2" (6.4 cm) wide tunnel and can be used on both Twin Cam Softail and Custom frames.available with raw steel or chrome plated dash. Holds approx. 5 1/4 Gallon (20 ltr). ONE PIECE 4" STRETCHED STEEL GAS TANK FOR SOFTAIL MODELS WITH DASH MOUNT These one piece gas tanks with dash mount will give your Softail that long, extra slippery stretched look and flowing lines. These tanks are made by welding a 2" extension to our stretched tanks making them in total 4" (10 cm) longer than stock. The extra stretch provides that special slim look. Tank has a seat pocket to match with most narrow seats, such as our Silhouette seats. Fits Softail models 84 thru 99. Tank holds approx. 4.2 gallon (15,9 ltr) and is available for Screw-In type gas caps as well as our Quick Cam lockable gas caps. 011631 Dual Screw-In type gas tank with dash mount (style B) 011632 Dual lockable Quick Cam flush mount gas tank with dash mount (gas caps are included) Tank for Screw-In type gas caps (Style B) 012902 With raw dash 012903 With chrome dash 2" STRETCHED GAS TANK FOR SOFTAIL TWIN CAM MODELS This one piece flat top 2" stretched gas tank fits for carbureted Softail models from 2000 thru 2003. Has a center mounted bung to take one OEM style screw-in style gas cap. Tank has no provision to install a dash. Mounting hardware and gas caps are not included. 012834 Fits 2000 thru 2003 carburetor equipped Softails (takes cap style B) ONE PIECE 2" STRETCHED TANK WITH DASH MOUNT FOR FXR This one-piece stretched gas tank has a proper dash mount, and will give your FXR the long, stretched look and flowing lines that go with our other stretched tanks, together with that classic dash look. The stretched section is not a weld-on part but an integral part of the tank and has a seat pocket to go with most narrow seats.tanks hold approx. 4.2 gallon (15,9 ltr) of fuel and are available with dual Screw-In type gas caps as well as dual Quick Cam lockable flush mount gas caps. 011637 Stretched gas tank with dual Screw-In typegas cap (style B) 011638 Stretched gas tank with dual Quick Cam lockable flush mount gas cap, caps included (style D) -010

Gas Tank ONE PIECE STRETCHED SMOOTH TOP STEEL GAS TANK FOR FXR MODELS This one piece stretched smooth top gas tank will give your FXR the long, slippery stretched look and flowing lines as found in our other stretched tanks. The stretched section is not a weld-on part but an integral part of the tank and has a seat pocket to match with most narrow seats.tank will hold approx. 4.2 gallon of fuel (15,9 ltr) and is available with single or dual Screw-In type gas caps, single or dual Quick Cam lockable flush mount gas caps,aero-style gas cap, and with the newest Pop-Up gas cap in a paintable and a chrome finish. Tank for Screw-In type gas cap (style B) 011634 Single cap stretched gas tank 0116 Dual cap stretched gas tank Tank complete with Quick Cam lockable flush mount type gas caps (style D) 011636 Single cap stretched gas tank 011635 Dual cap stretched gas tank Tank complete with large Aero-style chrome plated lockable aluminum gas cap (style F) 011737 Single cap stretched tank 011525 Replacement Aero gas cap large (style F) ONE PIECE 2" STRETCHED SMOOTH TOP STEEL GAS TANK FOR DYNA MODELS This one piece stretched smooth top gas tank will give your Dyna Glide the long, slippery stretched look and flowing lines associated with Low Rider Custom bikes.the stretched section is not a weld-on part but an integral part of the tank and has a seat cut out to match with most narrow seats, such as our Silhouette seat.tank holds approx. 4.2 gallon of fuel (15,9 ltr) and is available with Screw-In type gas caps,quick Cam lock gas caps, single Aero-style gas cap and with the new Pop-Up gas caps in a paintable and chrome version. Gas tanks for use with Screw-In type gas caps, caps not included (style B) 011639 Single cap stretched gas tank 011620 Dual cap stretched gas tank Gas tanks for use with Quick Cam, lockable, flush mount caps, gas cap(s) included (style D) 011641 Single cap stretched gas tank 011640 Dual cap stretched gas tank Gas tanks for use with large single Aero-style chrome plated lockable gas cap, gas cap included (style F) 011740 Single cap stretched gas tank Tank complete with center fill single cap Pop-Up gas cap (style G) 011848 With paintable Pop-Up gas cap 011849 With chrome Pop-Up gas cap Gas tanks for use with single Pop-Up gas cap, gas caps included (style G) 011852 With paintable Pop-Up gas cap 011853 With chrome Pop-Up gas cap GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -011

Gas Tank ONE PIECE 2" STRETCHED TANK WITH DASH MOUNT FOR DYNA GLIDE This one-piece stretched gas tank has a proper dash mount, and gives your Dyna the long, stretched look and flowing lines found on the one piece stretched tanks, together with that classic dash look.the stretched section is not a weld-on part but an integral part of the tank and has a seat pocket to go with most narrow seats. Tanks hold approx. 4.2 gallon (15,9 ltr) of fuel and are available with dual Screw-In type gas caps as well as dual Quick Cam lockable flush mount gas caps. 011642 Stretched gas tank for dual Screw-In type (style B) 011643 Stretched gas tank with dual Quick Cam lockable flushmount type gas caps, caps included (style D) FAT BOB TANK FOR HARLEY FXR MODELS This tank will create the Classic Harley Fat Bob look for the 82 thru 94 FXR models. It has the appearance of the Classic split Fat Bob tanks but is really a one piece tank assembly.tank accepts screw type gas caps or the latest design "Quick Cam" lockable flush mount, stock style petcock and FL-FXWG style large speedo dash. Bolts directly to the stock mounts. Each tank includes our ZPN 114246 Speedo cable (front wheel drive with 5/8" or 16 mm cable to speedo nuts) and a chrome tank divider panel (3.5 gallon, 13,2 ltr). 011348 Screw-In type gas tank (style B) 011564 Quick Cam lockable flush-mount type tank, includes set of gas caps (Style D) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT IS NOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. QUICK BOB STYLE SMOOTH TOP TANKS FOR DYNA AND FXR Superb quality gas tank. Ideal for applications where tank mounted speedometer is not wanted. These tanks have an improved mount at the front and back.available for Dyna Glides 90 to present and FXR models 84 thru 94. They are designed to bolt to the original mounts and feature Screw-In type gas caps (3.5 gallon, 13,2 ltr) (style B). 011572 FXR smooth top tank 011573 Dyna Glide smooth top tank -012

Gas Tank QUICK BOB TANK FOR DYNA GLIDE MODELS They have changed the mountings of this very popular tank to fit Dyna Glide models from 91 to present. It comes with a show-chromed dash panel to get the "Split Tank" Fat Bob look. The Dyna Quick Bob includes a bracket to accept the OEM FXDWG dash as well as the Old Style 2 or 3 light FL dashes with large style speedometer.available with Screw-In gas caps as well as the Flush mount Quick Cam lockable gas cap (flush gas caps are included with the tank). Tank has extra large 3.5 gallon capacity (13,2 ltr) for long hauls. Hardware kits are separately available. 011482 Screw-In type gas tank (style B) 011566 Quick Cam lockable flush mount style, includes gas cap set (style D) 345263 Hardware set STOCK STYLE GAS TANKS FOR 83 THRU 2003 SPORTSTER MODELS The upgraded stock style Peanut Sportster gas tank with improved rubber mount. Rubber mounts isolate the tank from the engine vibration and prevent cracking of the welds.this is a great improvement over the Original Equipment tank.tank holds approx. 2.25 gallon (8,5 ltr) and is available with a Screw-In type gas cap (style B) type and the late custom style Pop- Up gas cap (style G).The Pop-Up gas cap is included with the tank. Fits 83 thru 94 models 011484 Tank for Screw-In gas caps (OEM 61023-93) (style B) Fits 95 thru 2003 011496 Tank for Screw-In gas caps (61348-96A) (style B) 011824 Tank with paintable pop up gas cap (style G) PEANUT STYLE TANKS FOR 2004 TO PRESENT SPORTSTER MODELS Peanut style tanks to fit 2004 to present stock Sportster frames. Fuel capacity is approx. 3.9 gallon (14,8 ltr). Available complete with your choice of Quick-Cam, Aero-style or Pop-Up style gas cap. Tanks are 49 cm long, 28 cm wide, and 20 cm high. GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT IS NOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. Fits 2004-2006 Fuel Injected XL models, 3,9 Gallon 012805 Tank with Aero-style gas cap (style E) 012806 Tank with Pop-up style gas cap (style G) Fits 2007 to present Fuel Injected XL models, 3,9 Gallon 012916 Smooth Style tank with screw bung, takes stock style gas cap (style B) 012917 Smooth Style tank complete with quick-cam style gas cap (style D) 012920 Tank with side indents and screw bung, takes stock style gas cap (style B) 012921 Tank with side indents and complete with quickcam style gas cap (style D) -013

Gas Tank CUSTOM 2" STRETCH TANK FOR 2004 TO PRESENT SPORTSTER Custom 2" stretched tanks to fit directly all 2004 thru 2006 XL models. These stretched tanks feature a fluent swage line and fit most narrow seats (e.g. our Silhouette seats). Tank holds approximately 3.3 gallon (12,5 ltr) and comes complete with mounting hardware. Fits 2004-2006 XL models, 3,3 gallon 012802 Tank with screw bung, takes stock style gas cap (style B) 012809 Tank complete with Aero Style gas cap (style F) 012810 Tank complete with pop-up gas cap (style G) Fits 2007 to present Fuel Injected XL models, 3,3 Gallon 012924 Smooth Style tank with screw bung, takes stock style gas cap (style B) 012925 Smooth Style tank complete with quick-cam style gas cap (style D) KING SPORTSTER GAS TANKS Zodiac's King Size tanks for Sportster models have been a popular choice of Custom bike builders for many years.through the years it has almost become a standard upgrade for those who want the mileage. This classic "King Sportster" gas tank is now also available with the late OEM style Screw-In gas cap as well as the latest fashion "Pop-up" gas cap for the 82 thru 94 models. Will bolt to the Stock frame mounts on all 79 to 94 Sportsters, including the Evolution models. Has a larger than stock fuel capacity for extra mileage. Holds approx. 3.1 gallon (11,7 ltr). Fits 79 thru 81 models 011148 Cam lock type gas caps (style A) Fits 82 thru 94 models 011378 Screw-In type gas caps (style B) 011830 Paintable pop up gas cap (style G) 011831 Chrome pop up gas cap (style G) EXTENDED CLASSIC PEANUT STYLE GAS TANK FOR SPORTSTER MODELS They have extended the Original style Peanut style gas tank to give it a sleeker look and add some fuel capacity. It is available with two different petcock locations, one to fit Sportster models from 82 thru 94 the other to fit 95 thru 2003. This large capacity tank holds 3.25 gallon (12,2 ltr) fuel, and is designed to maintain the classic "Peanut" profile. It still looks like an integral part of the motorcycle and not just like an over-sized bolt-on accessory. Both tanks take Screw- In type caps (style B). 011399 Fits models 82 thru 94 011495 Fits models 95 thru 2003 GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -014

Gas Tank RUBBER MOUNT KING SPORTSTER GAS TANKS Zodiac's King Size tanks for Sportster models have been a popular choice of Custom bike builders for many years.through the years it has become the "classic" choice for those who want the mileage.we upgraded this classic "King Sportster" gas tank with rubber mounts to isolate it from the engine vibration, and add four style gas caps, being the stock style Screw-In, the Quick Cam lockable flush mount, a chrome plated lockable Midi Aero-style aluminum gas cap and the latest Popup gas cap in a paintable as well as a chrome plated finish. Except for the stock style Screw-In type tanks, gas caps are included with the tanks. Will bolt to the Stock frame mounts. Available for 82 thru 2003 Sportster including the Evolution Sportster. Has larger than stock fuel capacity for extra mileage. Holds approx. 3.1 gallon (11,7 ltr). Fits 82 thru 94 models 011483 For Screw-In type gas caps (style B) 011556 Quick Cam lockable flush mount tank, includes gas cap (style D) 011741 Aero-style gas tank, includes Midi aluminum lockable gas cap with chrome plated finish (style E) 011833 With chrome pop up gas cap (style G) Fits 95 thru 2003 011497 For Screw-In type gas caps (style B) 011559 With Quick Cam lockable flush mount tank (style D) 011742 With chrome plated Midi Aero-style aluminum lockable gas cap (style E) 011834 With paintable pop up gas cap type (style G) Replacement gas caps 011549 Lockable gas cap set (style D) 011526 Replacement Aero-style gas cap Midi vented (style E) 011551 Vented Quick Cam gas cap (style D) LATE STYLE ROLLED EDGE KING TANK FOR SPORTSTER This tank has it all, the classic Peanut profile with the latest style rolled edges and increased fuel capacity for the extra miles. Holds approx. 3.4 gallon (12,9 ltr). Perfect for crash repairs or updating older models. Tanks come complete with mounting hardware and rubber grommets. Available for use with OEM or aftermarket Screw-In gas cap. For those who want something else we also supply these tanks with various Custom gas caps, such as a chrome plated and lockable aluminum Aero-style gas cap, or Pop-up style gas cap in a paintable or chrome finish. Except for Screw-In type tanks, gas cap(s) are included with the tank. Center fill, fits 82 thru 94 Sportster models with S&S Super E or G carburetor 011701 For Screw-In style gas cap (style B) 011743 With midi Aero-style lockable gas cap (style E) 011836 With paintable Pop-up gas cap (style G) 011837 With chrome Pop-up gas cap (style G) Center fill, fits 95 thru 2003 Sportster models 011575 For Screw-In style gas cap (style B) 011744 With midi Aero-style lockable gas cap (style E) Replacement Midi Aero-style gas cap 011526 Replacement Aero-style gas cap Midi vented (style E) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -015

Gas Tank ONE PIECE SPORTBOB TANKS FOR SPORTSTER These tanks have an improved rubber mount at the front and back. Available for Sportster models 57 thru 78 and 82 thru 2003. Tanks are designed to bolt to the original mounts. 82 to present tank is available with Screw-In type gas cap, the Quick Cam lockable flush cap, a large chrome plated and lockable aluminum Aero-style gas cap, and the latest Pop-up style gas cap. Except for the cam lock and Screw- In style, the gas cap are included with the tank. Combine this tank with our Wide Glide conversion kit, Ducktail front fender and a nostalgic seat to create your own Heritage look. Tank holds approx. 3.8 gallon (14,4 ltr). Fits 57 thru 78 011322 Dual cap Cam lock style tank (style A) Fits 82 thru 2003 011473 Dual cap Screw-In style tank (style B) 011561 Dual cap Quick Cam lockable style tank, gas caps included (style D) 011745 Single cap Aero-style gas tank, large chrome plated lockable gas cap included 011842 With single paintable pop-up gas cap 011843 With single cap with chrome pop-up gas cap (style G) Note: Installation of ZPN 011473, 011561 and 011745 tanks on 95 thru 2003 Sportster models requires the use of ZPN 011570 ignition switch and coilrelocation kit. This kit must be ordered separately. 011570 Ignition switch and coil relocation kit for 95-2003 Sportster models ONE PIECE RUBBER MOUNT QUICKBOB GAS TANK FOR 82 THRU 2003 SPORTSTER MODELS Re-designed Quickbob tank to fit the 82 thru 2003 Sportster models. At the same time the rigid mount was changed to an improved rubber mount which isolates the tank from the engine vibration and added threaded dash mounting holes. Each tank comes complete with dash base and a chrome plated dash. This dash accepts the large FL style speedometers and has no ignition switch hole, so rewiring is not needed. Dashes are also separately available.also available is a special dash with a smaller hole to accept the 95 thru 2003 Original Equipment Sportster speedo. Tank holds approx. 4 gallons (15,1 ltr) which is almost twice as much as the original tank. Screw-In type gas tank (style B) 011474 Fits 82 thru 2003, includes FL speedo type dash 013083 Chrome plated dash for large FL type speedo 345276 Optional dash cover for stock Sportster 95 thru 2003 (except XL883C and XL1200C) electronic speedometer IGNITION SWITCH AND COIL RE-LOCATION KIT FOR 95-2003 SPORTSTER When installing our rubber mount tanks on95-2003 Sportster models, the front bracket will interfere with the ignition switch. With this bracket-set the ignition switch is re-located under the top motor mount bolt of the rear cylinder. Also the coil needs to be relocated, therefor this chrome plated coil bracket is included. 011570 Ignition switch and coil relocation kit for 95-2003 Sportster models -016

Gas Tank ONE PIECE "RUBBER MOUNTED" FAT BOB TANK FOR SPORTSTER Another of Zodiac's top quality gas tanks.tanks have an improved "All rubber mount" at the front and back, which isolate the tank from the vehicle's vibration. Fits all Sportster models 57 thru 2003 (except 79-81) including the Evolution models.tanks are designed to bolt to the original mounts and accept the 2-light or 3-light dash with large FL style speedo. 57 thru 78 model has cam lock gas, 82 thru 2003 has Screw-In type gas caps. The 82 thru 2003 model is also available with the Quick Cam lockable flush mount gas caps. These flush mount tank do include a set of lockable gas caps. Combine this tank with our Wide Glide conversion kit, Ducktail front fender and nostalgic seat to create your own Heritage look. Tank holds approx. 3.3 gallon (12,5 ltr). Mounts are separately available. Fits Sportster models 57 thru 78 011306 Cam lock style gas cap tank (style A) Fits Sportster models 82 thru 2003 011308 Screw-In style gas cap tank (style B) 011560 Quick cam lockable flush mount style gas cap tank, includes gas caps (style D) 011549 Lockable gas cap set (style D) Fits Sportster models 82 thru 2003 345286 Rear mount with rubbers ONE PIECE STRETCHED SPORTBOB TANKS Initially the stretched style tanks were made by welding an extension to the rear of the tank but Zodiac has the real thing. This smooth top stretched Sportster tank has it all and adds more style to your machine. These tanks are available in a dual or single cap for Screw-In, lockable, flush mount Quick Cam gas caps,aero-style chrome plated and lockable aluminum gas caps as well as latest style Pop-up gas caps.flush mount, Aero and Pop-up gas tanks include gas cap(s). Holds approx. 4 gallon (15,1 ltr) of gas and comes complete with mounting hardware. Fits Sportster models 82 thru 2003. Note: 95 thru 2003 models require our switch & coil relocation kit ZPN 011570. Screw-In type stretched gas tank (style B) 011586 Single cap gas tank 011583 Dual cap gas tank Quick Cam lockable Flush mount type gas tank, includes gas cap(s) (style D) 011589 Single cap gas tank 011588 Double cap gas tank Center fill Aero-style gas tank, includes large chrome plated and lockable aluminum gas cap (style F) 011746 Single cap gas tank Fits Sportster models 82 thru 2003 345287 Front mount with rubbers GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT IS NOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. Center fill Pop-up style gas tank, includes gas cap (style G) 011840 With paintable Pop-up gas cap 011841 With chrome Pop-up gas cap Replacement gas caps 011549 Lockable gas cap set (style D) 011525 Replacement Aero gas cap large (style F) 011551 Vented Quick Cam gas cap (style D) 012100 Pop-up style gas cap, raw (style G) 012101 Pop-up style gas cap, chrome (style G) -017

Gas Tank ONE PIECE 2" STRETCHED STEEL TANK WITH INDENTS FOR SPORTSTER MODELS 2" Stretched one piece tanks. No weld-on stretched sections, just one piece high quality steel. Indents on both sides of these tanks add a touch of class. Please note that the seat cutout at the stretched sections matches most narrow model seats, e.g. Silhouette. Available for use with OEM style screw-in gas cap or complete with Quick Cam Aero Style or pop-up gas cap. Must be used in combination with a 13/16" (22 mm) petcock. Tanks hold approx. 4 gallon (15,1 ltr) and come complete with hardware. Fits 95 thru 2003 XL models 0128 Tank for screw-in style cap (style B) 012821 Tank with Aero-style lockable cap (style F) Fits 2004 thru 2006 XL models 012823 Tank for screw-in style cap (style B) 012825 Tank with Aero-style lockable cap (style F) 012826 Tank with pop-up style cap (style G) ONE PIECE STRETCHED SPORTBOB TANKS WITH DASH MOUNT FOR 82 THRU 2003 SPORTSTER MODELS This 2" stretched Sportbob tanks with dash mount, will give your Sportster the long slippery stretched look as found on our other stretched tanks.tanks have an improved rubber mount system which isolates the tank from the engine vibrations. Designed to bolt to the original mounts and accept the 2-light or 3-light dash with large FL style speedo. Fits Sportster models 82 thru 2003. Holds approx. 4 gallon (15,1 ltr), which is almost twice as much as the original tank.available dual Screw-In type gas caps as well as with dual Quick Cam lockable gas caps. Note: 95 thru 2003 models require use of our switch and coil relocating kit ZPN 011570. 011601 Dual Screw-In type cap gas tank (style B) 011602 Dual Quick Cam lockable gas caps, gas caps included (style D) 011549 Lockable gas cap set (style D) 345286 Rear mount with rubbers 345287 Front mount with rubbers Fits 2007 to present Fuel Injected XL models, 4 Gallon 012928 Tank for screw-in style cap (style B) 012929 Tank with quick-cam style cap (style C) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT IS NOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. CHROME RE-LOCATION IGNITION SWITCH COVER This chrome ignition switch cover is a must when you relocate the ignition switch on your Sportster or Big Twin. It covers the unfinished bottom end of the ignition switch for a cleaner appearance. 370060 Custom ignition switch cover -018

Gas Tank 2" STRETCHED RUBBER MOUNT SPORTBOB TANK WITH DASH FOR 95 THRU 2003 SPORTSTER MODELS This 2" stretched Sportbob tank with dash will give your Sportster the long slippery stretched look.tank has an improved rubber mount system which isolates the tank from most engine vibrations. Designed to bolt to the original mounts of 95 thru 2003 Sportster models.tank comes complete with dash base plate, 3 light dash to take a OEM Big-Twin style electronic speedometer, 6 post Fat Bob style ignition switch, coil relocation bracket and all hardware needed. Tank holds approx. 3.4 gallon (12,9 ltr), almost twice as much as the original tank. Available with either dual Screw-In type gas caps or dual Quick Cam lockable gas caps. A dash cover to take an OEM Sportster electronic speedometer must be ordered separately. 011605 Dual Screw-In type gas tank with dash and switch kit (style B) 011606 Dual Quick Cam lockable gas tank with dash and switch, gas caps included (style D) 345276 Optional dash cover for stock Sportster 95 thru 2003 (except XL883C and XL1200C) electronic speedometer ONE PIECE STRETCHED TANK, DASH & SPEEDO KITS FOR SPORTSTER MODELS Custom style one piece stretched gas tank with tank mounted dash. This tank gives your Sportster the popular long, slippery stretched look and flowing lines.the tank mounted Fat Bob dash kit adds the Big Twin look.this very complete kit includes the gas tank, with your choice of Screw-In style gas caps or Quick Cam flush mounted locking gas caps, a chrome plated 3 light dash complete with dash base plate, speedometer in KPH with reset knob, speedo damper rubber and 6 post Fat Bob ignition switch. The stretched section is not a weld-on part but an integral part of the tank and has a seat pocket to match with most narrow seats, such as our Silhouette seats.tank holds approx. 3.4 gallon of fuel (12,9 ltr). Fits 82 thru 94 Sportster models. 011612 Stretched gas tank with dash kit and dual Screw- in style caps (style B) 011613 Stretched gas tank with dash kit and dual Quick- Cam lockable flush mount gas caps (style D) Replacement dash mount and dash cover, fits ZPN 011605, 011606, 011612 and 011613 011658 Dash cover 013068 Dash base -0

Gas Tank CRUISE SPEED TEARDROP GAS TANKS FOR 2004 THRU 2006 SPORTSTER These teardrop style gas tanks, with their rounded shape and smooth fluent lines, drastically change the looks of your Sportster. No expense was spared in the construction and finish quality of these gas tanks. When mounted on your Sportster you will notice that there are no visible welds, as these have been finished to give a seamless appearance. Tank holds 3.5 Gallon (13,2 ltr) to allow you to go the distance.available to take a stock screw-in style gas cap. Gas cap must be ordered separately.tanks fit 2004 thru 2006 Sportster models. 930185 For screw-in style gas cap (style B) MUSTANG RIBBED GAS TANK Mustang style steel gas tank with a design that is inspired by Vintage American cars and motorcycles. Features a classic style ridge from front to rear. Tank holds 3.3 Gallon (12.5 ltr), is 17" (43 cm) long, 11 1/2" (29 cm) wide and has a 2" (5 cm) wide low tunnel. Has universal brackets that makes it easy to mount it to almost any stock or custom frame.the Mustang "ribbed" gas tank is available with screw bung to take a stock or aftermarket 82-up style vented gas cap, as well as complete with a pop-up style gas cap. Matching design front fender can be found in Chapter 18. 012890 With screw-in style bung (style B) 012892 Complete with pop-up style gas cap (style G) CUSTOM GAS TANKS Our gas tanks are made from thick gauge quality steel, all welds are quality checked, they feature two sizes of petcock connecting thread to take early style petcocks with 3/8" NPT or 1/2" NPT Custom petcocks.tanks will take our universal or deluxe gas cap (see gas cap section) and have universal mount for many Custom applications. 011129 "King" Sportster Model 3.1 Gallon (11,7 ltr) 011265 Sportster Model 2.4 Gallon (9.1 ltr) WASP STYLE MUSTANG GAS TANK Wasp style narrow Mustang gas tanks for custom applications that have a great vintage look. Made from precision steel stampings and tig welded, these tanks hold 2.2 Gal (8.4 Liter) and have a right side petcock opening. Universal brackets make it easy to mount it to any stock or custom frame.available in a single or dual bung version, where the left filler is a dummy and uses old school cam lock type gas caps. 012893 Single cap Wasp gas tank (style A) 012894 Dual cap Wasp gas tank (style A) -020

Gas Tank CRUISE SPEED SMOOTHIE CUSTOM GAS TANK No expense was spared in the construction and finish quality of these steel gas tanks. They feature joggle lap and lap joints through out, resulting in a super-strong gas tank without the worry of compromising the structural strength while providing a smooth surface finish. The joggle lap joints also allow the tunnel plate to be sunken below the bottom surface of the tank, making grinding of the welds unnecessary. Tank is mounted to the frame using the supplied weld-on frame brackets, which feature a recessed rubber mounting system to isolate the tank from vibrations.tank has 22 1/4" length with a 1/4" long, 3 1/2" wide tunnel and a 3" deep seat pocket. Holds approx. 4 Gallon (15,1 ltr) of fuel. Comes complete with mounting hardware and features 13/16" (22 mm) petcock outlet, breather tube and rear gas crossovers tapped for 1/8"-27 NPT unions. Gas cap is not included but must be ordered separately. 930147 Smoothie gas tank for pop-up style gas cap (Style G) 012100 Pop-up style gas cap, raw (style G) 012101 Pop-up style gas cap, chrome (style G) CRUISE SPEED CUSTOM GAS TANK Steel gas tank for custom applications.all welds that are in sight when these tanks are mounted have been finished and polished to give a nice smooth seamless appearance. Tanks are to be mounted on the frame with the included weld-on brackets, which feature a recessed rubber mounting system to isolate the tank from vibration.tank is 21 1/4" long, 14" wide, 9" high and has a 3 1/4" wide tunnel. Holds approx. 3.5 Gallon (13,2 ltr) of fuel. Takes 13/16" (22 mm) fuel tap. Gas cap is not included. 9300 Custom gas tank for pop-up gas cap (Style G) 012100 Pop-up style gas cap, raw (style G) 012101 Pop-up style gas cap, chrome (style G) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -021

Gas Tank CRUISE SPEED "HEAVY METAL" TORPEDO STYLE CUSTOM GAS TANKS Cruise Speed gas tanks are the strongest gas tanks on the market as they are made from heavy gauge steel with lap joints throughout. These Torpedo Style Custom gas tanks feature a ridge line from front to rear. Low Tunnel tanks have a 21 3/4" (55 cm) long and 2 1/2" (6.3 cm) wide tunnel, are 9 3/4" (almost 25 cm) wide, 8 1/2" (21 cm) high and hold 3 1/8 Gallon (11,7 ltr) of fuel. High Tunnel tanks have a 23" (58.5 cm) long and 2 3/8" (6 cm) wide tunnel, are 12" (30.5 cm) wide and hold 3 3/8 Gallon (12,97 ltr) of fuel. Both High and Low Tunnel tanks are available for use with a stock style cam lock or stock style screw-in type gas cap. Low Tunnel tanks 930183 For use with cam lock style gas cap 930184 For use with screw-in style gas cap High Tunnel tanks 930178 For use with cam lock style gas cap 930179 For use with screw-in style gas cap CRUISE SPEED "HEAVY METAL" TEARDROP STYLE CUSTOM GAS TANKS Cruise Speed gas tanks are the strongest gas tanks on the market as they are made from heavy gauge steel with lap joints throughout. These Teardrop Style Custom gas tanks have a 23" (58.5 cm) long and 3" (7.5 cm) wide tunnel, are 15" (38 cm) wide and hold 4 3/4 Gallons (17,8 ltr) of fuel.tanks are available for use with a stock style cam lock or stock style screw-in type gas cap. 930170 For use with cam lock style gas cap (Style A) 930171 For use with screw-in style gas cap (Style B) -022

Gas Tank IMAGE SERIES STRETCHED CHOPPER TANKS These Image Series chopper tanks are real smooth looking pieces of art and really complete the smooth looks of North Sea Chopper frames or other frames with a 4" stretch in the downtubes, 3" minimum backbone stretch, and a top tube not exceeding 1 1/2" in diameter.the tanks come with weld-on mounting brackets, which are recessed in the bottom of the tank for a smooth hidden look. Tanks are tapped 1/8"-27 NPT at the rear of the tank for the fuel crossover line, and must be used with a 13/16" (22 mm) petcock. Capacity is approx. 5.2 gallon (,7 ltr) for the shortest version. Tanks are supplied complete with your choice of a flush mount or raised bung chrome pop-up gas cap.the 6" stretched version is also available for use with a stock style screw-in type gas cap. 23 1/2" long chopper tanks for 4 1/2" stretched frame 011703 Complete with flush mount chrome pop-up gas cap (style G) 011704 Complete with raised bung chrome pop-up gas cap (style G) 0118 Replacement chrome pop-up gas cap PRO IMAGE II SERIES 6" STRETCHED CHOPPER TANKS Pro Image Series tanks in the 6" stretched version feature pointed ends, especially designed for 6" stretched High Neck Chopper frames, like our North Sea Chopper edition.all Pro Image II series tanks feature extra wide tunnels to accept even 2 3/8" top tube Chopper frames. Each tank is equipped with recessed bolt-on mounting brackets for a smooth and hidden look. Come complete with mounting hardware, even to fit "rubber-mounted" applications, and pop-up gas cap. 012837 Tank with pop-up cap (style G) IMAGE SERIES STRETCHED CHOPPER TANKS A number of great designs in our Image Series are these stretched chopper tanks. Smooth looking and enhancing the lines of our High Neck Chopper frames. Also look great on any frame with stretched downtubes and 3" or more stretch in the backbone.tanks come with weld-on mounting brackets, which are recessed in the bottom of the tank for a smooth hidden look.the rear of these tanks are tapped 1/8"- 27 NPT to take a fuel crossover line,and must be used with a 13/16"(22 mm) petcock. Tanks are available complete with chrome pop-up gas cap in flush mount or raised bung style, or as a screw-in style tank without gas cap. 23" Long chopper tanks with standard tunnel for up to 1 1/2" top tubes, 15.5 ltr (4.1 gallon) 011664 Complete with flush mount chrome pop-up gas cap (Style G) 011665 Complete with raised bung chrome pop-up gas cap (Style G) 23" Long chopper tank with extra wide tunnel for up to 2 3/8" top tubes, ltr (5.2 gallon) 0146 Complete with flush mount chrome pop-up gas cap (Style G) 25" long chopper tanks for 6" stretched frames with up to 2" top tubes, 17,5 ltr (4.7 gallon) 0135 Complete with flush mount chrome pop-up gas cap (Style G) 0139 For screw-in type gas cap (Style B) 26 1/2" Long chopper tanks for 7 1/2" stretched frames with up to 2 1/4" top tubes, 20 ltr (5.4 gallon) 0136 Complete with flush mount chrome pop-up gas cap (Style G) 0118 Replacement chrome pop-up gas cap -023

Gas Tank PRO IMAGE 2 SERIES STRETCHED GAS TANKS These indented design gas tanks are very smooth looking and enhance the lines of the High Neck Chopper frames. Available for frames with 4" or 6" down tube stretch and 3" minimum backbone stretch. The tunnel easily fits top tubes up to 2" diameter. Tanks come with weldon mounting brackets, which are recessed in the bottom of the tank for that smooth hidden look.the rear of the tank is tapped 1/8"-27 NPT to take a fuel crossover line.to be used in combination with a 13/16" (22 mm) petcock. Tanks for 4" stretched frames 4,5 Gallon (17 ltr) 012116 Complete with flush mount chrome pop-up cap (Style G) Tanks for 6" stretched frames, 5,2 gallon (.5 ltr) 0121 Complete with flush mount chrome pop-up cap (Style G) CUSTOM ALUMINUM GAS TANK FOR TWIN CAM SOFTAIL, AND 89 TO PRESENT SPORTSTER MODELS European made aluminum Custom tank as a bolt-on tank for 2000 thru 2006 carburetor equipped Twin Cam Softail models, but also fits 89 thru 2006 carburetor equipped Sportster models when you order the optional bracket kit ZPN 722082. This Custom tank will greatly improve the looks of your bike.it is a direct replacement for the standard tank and fits with the stock seat without any trouble and features swage line that accents the tank line.tanks are available with aluminum dash, to take the OEM dash, or as a smooth top tank. Tank holds approx-imately 4.25 gallon (16 ltr) of fuel. The version with the aluminum dash comes complete with a pop-up gas cap on the right side.the version with the mounts for the OEM dash is designed for use with an Aero style gas cap, such as ZPN 232153 or ZPN 232154. The smooth top tank takes gas cap ZPN 237353. 722078 With aluminum dash and pop-up gas cap 722084 Custom aluminum fuel tank for OEM dash 722081 Custom aluminum fuel tank, smooth top 722082 Optional bracket kit for 89 thru 2006 Sportster models CUSTOM ALUMINUM GAS TANK FOR TWIN CAM SOFTAIL MODELS WITH POP UP GAS CAPS This tank is designed to fit the 2000 to present Twin Cam Softail models. Tank has very smooth flowing lines and is narrow ended on the seat side. Can be used to replace the standard tank, but will not work with stock seat.tank includes an aluminum dash, and two pop-up type gas caps. Holds approximately 4.25 gallon of fuel (16 ltr). 722079 Tank with dual pop-up gas caps GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT ISNOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -024

Gas Tank CUSTOM ALUMINUM GAS TANKS These gas tanks are manufactured by Europe's leading manufacturer of aluminum gas tanks. For decades many factory race teams used them to manufacture strong and light weight gas tanks for their race bikes. Since a few years they are making special designed, high quality aluminum Custom tanks for the Harley-Davidson aftermarket.we offer a wide variety of these handcrafted aluminum tanks. Each tank is hand formed and hand welded by guys that know what they are doing.years of experience made them the best in the industry. All tanks are leaktested before they leave the factory.available as a bolt on for Sportster models, Softail models, FXR models, Dyna Glide models as well as a number of models for the Custom builder that wants to fit it on a "One- Off" Custom frame. Tanks can be Custom painted or polished to a chrome-like finish.also check out the pricing of these tanks. For the high quality product they are very economically priced. Tanks include mounting brackets where needed.all tanks have single gas cap, caps are not included.the racing type caps can be bolted-on as tank come with a flat surface and threaded holes, these tanks also have inside breather tube. For those with an eye for detail we offer most models with a Swage Line. Fits Evolution Softail models, 4 gallon/15,1 ltr takes gas cap ZPN 232153 or 232154 711227 Softail Aero 711240 Softail Aero with Swage Line Fits Dyna models, 4 gallon/15,1 ltr takes gas cap ZPN 232153 or 232154 711229 Dyna Aero 711241 Dyna Aero with Swage line Fits Sportster models, 2.9 gallon/11 ltr takes gas cap ZPN 232153 or 232154 711228 Sporty Peanut Aero 711239 Sporty Peanut Aero, with Swage Line Custom Cruiser Teardrop Tank with 2" stretch, 2 3/4 gallon/10.5 ltr, takes gas cap ZPN 237353, 237354 or 237359, fits most 2" stretched frames 711455 Custom Cruiser 2" stretch Fits FXR models, 4 gallon/15,1 ltr takes gas cap ZPN 232153 or 232154 711230 FXR Aero Fits FXR models, 4 gallon/15,1 ltr takes gas cap ZPN 232153 or 232154 711238 FXR Aero with Swage line Custom Cruiser Teardrop Tank with 5" stretch, 4 gallon/15,1 ltr, takes gas cap ZPN 237353, 237354 or 237359, fits most 5" stretched frames 711282 Super Cruiser 5" stretch -025

Gas Tank PEANUT STYLE ALUMINUM CHOPPER TANK Take a classic peanut style gas tank, bang it around a bit, stretch it to 23 1/2" length, add a flush mount pop-up gas cap and this is what you get: a great looking Peanut style Chopper tank. Comes complete with custom weld-on brackets. 741275 Peanut style aluminum chopper tank CUSTOM ALUMINUM KING CRUISER TANK With its 65 cm (25,6") length it is one of the longest custom fuel tanks available to day.takes 5,5 gallon (20,8 ltr). Comes complete with popup gas cap and custom weld-on mounting brackets. 741255 Custom alu King Cruiser tank extra long CUSTOM TANKS Custom made models for stock and after market frames.when installing these tanks it may be necessary to modify or make Custom brackets. We have indicated what type frame they are intended for but with Custom made brackets they will fit any frame. Fits Softail style, Softail stretched frames as well as Ness type stretched frames. TON PELS' SIGNATURE SERIES ALUMINUM TANK FOR GODFATHER FRAME This custom aluminum fuel tank matches the flowing lines of the Godfather frame.has a capacity of 6 gallon (22.7 ltr) and takes gas caps ZPN 237353, 237354, and 237359. 722083 Tank for Godfather frame FishTail model, 5 gallon/18,9 ltr takes gas cap ZPN 237353, 237354 or 237359 711233 FishTail 2" Stretched 711242 FishTail 2" Stretched with Swage Line CUSTOM ALUMINUM SMOOTH TOP GAS TANK FOR TWIN CAM SOFTAILS A Custom tank with smooth top to fit 2000 to present Twin Cam Softail models.this aluminum gas tank has very smooth flowing lines, with a very narrow end on the seat side.this tank can be used to replace the standard tank.will not work with the stock seat, must use narrow front aftermarket seat. Gas tank takes a center fitted Aero type gas cap ZPN 237353, 237354 or 237359. Gas cap must be ordered separately.tank holds approx. 4.25 gallon (16 ltr) of fuel. 722085 Twin Cam Softail Custom aluminum gas tank FishTail model, 6 gallon/22,7 ltr takes gas cap ZPN 237353, 237354 or 237359 711234 FishTail 5" Stretched 711243 FishTail 5" Stretched with Swage Line -026

Gas Tank Custom Softail, 4.2 gallon/15,9 ltr takes gas cap ZPN 232153 or 232154 711231 Softail 5" Stretched 711244 Softail 5" Stretched with Swage Line Fits Sportster type and Rigid frames, 4.5 gallon/17 ltr takes gas cap 232153 or 232154 711232 Sporty Peanut Stretched Super 2" stretch model, 6 gallon/22.7 ltr takes gas cap ZPN 237353, 237354 or 237359 711235 Super Stretch 2" 711245 Super Stretch 2" with Swage Line Limited Series King Cruiser Swage Line Tank capacity 5.5 gallon (20,8 ltr). Accepts Aero gas cap ZPN 232130 or 232136. Over all length 65 cm, 38 cm wide in front, 9 cm wide on the rear and cm maximum height. 711586 Limited Series King Cruiser Tank Super 5" stretch model, 6.9 gallon/26,1 ltr takes gas cap ZPN 237353, 237354 or 237359 711236 Super Stretch 5" 711246 Super Stretch 5" with Swage Line Custom Super Cruiser with 5" stretch Tank capacity 4.5 gallon (17 ltr). Accepts Aero gas cap ZPN 232130 or 232136. Tank is 63 cm long, 35,5 cm front width, 8.5 cm rear width, and cm high. 711587 Custom Super Cruiser Tank Softail Super 5" stretch model 4.2 gallon/15,9 ltr takes gas cap ZPN 237353, 237354 or 237359 This tank fits most 5" stretched Softail-style frames. The tank sits lower at the rear, covering the frame tubes giving a smoother line to the finished bike. 711237 Custom Softail 5" Stretch Limited Series Cruiser Swage Line Tank capacity 4.4 gallon (16.7 ltr). Accepts OEM style screw-in gas cap. Tank is 63 cm long, 31 cm wide in front, 5 cm wide in rear and 22 cm high. 711588 Limited Series Cruiser Tank -027

Gas Tank New Softail with 5" stretch Swage Line Tank capacity 4.2 gallon (15,9 ltr). Accepts Aero gas cap ZPN 232130 or 232136. Tank is 63 cm long, 9 cm wide in the rear, 33 cm wide in front and 23 cm high. 711589 New Softail 5" Stretch tank Limited Series Super Cruiser with 5" stretch Swage Line Tank capacity 4.2 gallon (15,9 ltr). Accepts Midi-Aero gas cap ZPN 237353, 237354 or 237359. Tank is 63 cm long, 9 cm wide on the rear, 34,5 cm wide in front and cm high. 711592 Limited Series Super Cruiser Tank Limited Series Softail with 5" stretch Swage Line Tank capacity 4.2 gallon (15,9 ltr). Accepts Aero gas cap ZPN 232130 or 232136. Tank is 63 cm long, 9 cm wide on the rear, 33 cm wide in front and 23 cm high. 711590 Limited Series Softail Tank King Super Cruiser Tank capacity 4.6 gallon (17,4 ltr). Accepts the large Aero gas cap ZPN 232130 or 232136. Tank is 63 cm long, 9 cm wide at the rear, 40.5 cm wide in front and cm high. 711593 King Super Cruiser Tank King Chopper Tank capacity 4.8 gallon (18,2 ltr). Accepts Aero gas cap ZPN 232130 or 232136. Tank is 61.5 cm long, 5 cm wide on the rear, 40.5 cm wide in front and 22 cm high. 711591 King Chopper Tank King Super Stretch Swage Line Tank capacity 6.2 gallon (23,5 ltr). Accepts the large Aero gas cap ZPN 232130 or 232136. Tank is 62 cm long, 14 cm wide in the rear, 38 cm wide in front and 22 cm high. 711594 King Super Stretch Tank -028

Gas Tank New 2" Super Stretch Swage Line Tank capacity 4.6 gallon (17.4 ltr). Comes complete with pop-up gas cap and custom weld on mounting brackets. Tank is 57 cm long, 13 cm wide on the rear, 38 cm wide in the front and 22 cm high. 711595 New Super Stretch Tank with pop-up gas cap CUSTOM ALUMINUM GAS TANK If you want the ultimate Custom stretched handmade aluminum gas tank that fits our Ton Pels Signature Series "Godfather" frame, or any other Custom frame your search is over.this tank is welded by experts and leak tested before it leaves the factory. Available with the flush mount pop-up cap for the ultimate Custom look. Tank contains 3.6 gallon/13,6 ltr, and has a tunnel length of 24.4" (620 mm).you do not have to make your own Custom bracket set because we already put one in, which has to be welded onto the frame. 7415 Custom aluminum chopper tank ROLAND SANDS DESIGN VINTAGE FUEL TANK KIT FOR TWIN CAM SOFTAILS This kit contains steel gas tank with steel backbone cover and all necessary hardware. Tunnel mounts to stock location and allows for use of stock ignition switch and key. Tank holds approximately 2.5 gallon (9.5 ltr).the kit for EFI equipped Softails also includes the Gasit fuel injection kit. Using the stock EFI components this kit relocates the fuel pump, regulator and filter to the underside of the tank. Giving you numerous possibilities for customization.weld in steel manifold and all fasteners are included. Special RSD gascap is not included, can be found elsewhere in this chapter. 740631 Carbureted fuel tank with backbone cover for 2000 thru 2006 Softail 740632 EFI fuel tank with backbone cover and Gas It kit for 2001 to present Delphi Fuel Injected Softail 740633 Carbureted gas tank only 740634 EFI gas tank only 740635 Steel backbone cover only 740630 Gas it fuel injection kit only If you start from scratch to build a Fuel Injected custom you will also need 740766 Fuel pressure regulator (OEM 27408-01) 740767 Fuel filter with clamps, O-ring and hose (OEM 61001-01) 740768 Fuel sender kit (OEM 75300-05) 740769 Fuel pump assembly (OEM 62897-01B) 740770 Check valve assembly with O-ring (OEM 62189-01A) GAS TANKS THE ZINC-CHROMATE PRIMER FINISH ON SOME OF OUR TANKS IS PROVIDED FOR THE PROTECTION OF THE TANKS DURING SHIPMENT AND STORAGE. IT IS NOT RECOMMENDED AS A PRIMER FINISH FOR PAINT APPLICATIONS WITHOUT PROPER SURFACE PREPARATION. AS WITH ANY FUEL TANK, PARTICULARLY ONE WHERE CUSTOM PAINT IS TO BE APPLIED, ALL TANKS MUST BE PRESSURE TESTED, THEN CLEANED WITH TANK CLEANER AND SEALED WITH TANK SEALER (SEE TANK CLEANER & SEALER ZPN 232020) BEFORE PAINTING, TO PROTECT THE FINAL FINISH AND PREVENT INTERNAL RUST DURING WINTER STORAGE. FUEL CAPACITY IS MEASURED WITH TANK IN UPRIGHT POSITION, ANGLE OF PARKED BIKE WILL DETERMINE ACTUAL CAPACITY OF THE FUEL TANK. -029

Gas Tank/Gas Tank Mounting Hardware NEVER RUN OUT OF GAS AGAIN WITH THE REDA JERRY CAN FOR BAGGER BAGS If you have ever had that sick feeling of running out of gas in the middle of the night without knowing where the next gas station is or when you do not want to find out, the REDA Gas Can is a must-have for you. The Reda jerry can is designed specifically for your Harley-Davidson saddlebags. Your riding pleasure and confidence goes way up knowing you have an extra gallon (almost 4 ltr) of gas sitting in one of your bags in case of that possibility of running out.as the Reda Gas Can fits left as well as right side saddlebags you can even take two of them, extending your driving range with an incredible 70 to 80 miles (110 to 130 km). They are Custom made to fit perfectly in that "hard to reach" back corner of the bag, so they hardly take up any space.the spill proof pouring spout sits under the cap inside the can, so it is there when you need it.the REDA Gas Can is EPA and CARB certified. Meeting these standards makes this gas can 100 % vapor proof and 100% spill proof, so there is no need to worry about fumes or gas in your bags. 742950 REDA gas can FUEL-TOOL FUEL TRANSFER SYSTEM Ever tried to siphon fuel from your Twin Cam gas tank to an other bike or jerry can? Most likely you found out that gas tastes bad and/or spilled a lot of this expensive stuff. There is a better way to do this, called the Fuel-Tool. The Fuel-Tool Motorcycle Fuel Sharing System connects to the fuel tank of any bike and allows you to transfer gas from one tank to another. The Fuel-Tool System also works great for draining the tank for seasonal storage. It is an easy to use system that installs in seconds and features automatic self-locking quick connectors to assure a fail safe connection. Connects to the factory installed Quick Connect on the left side of the gas tank on all Fuel Injected Harley-Davidson Twin Cam models 2001 to present. The fuel line from your bike reconnects to the Fuel-Tool and start your engine. Now you put the spiral hose with hand operated tap into the opening of the other tank or jerry can and your fuel pump does the rest. Do not use the Fuel-Tool near open fire, sparks or when smoking, but all the rest is as safe as filling your tank at a gas station.the Fuel-Tool comes with carry case and complete instructions. 747360 Fuel-Tool fuel transfer system RICK'S V-ROD GAS TANK Most V-Rod owners know that you have to start looking for the next gas station almost immediately when you have hit the road. Rick's gas tanks have a 1 gallon (3.8 ltr) larger capacity as the stock tank, which totals to 4.9 gallon (18.5 ltr).this increases your reach by approx. 35%. Tank comes in black painted finish. Takes the OEM gas cap, opening mechanism and electronics. Installation requires minor modifications on the protection plate under the tank. This is very easy when you follow the included step-bystep fitting instructions. Designed to go with stock or up-to 300 wide rear tire and matching swing arm on 2002 thru 2006 V- Rod models. 741395 Rick's V-Rod gas tank CUSTOM ALU TANK MOUNTING KIT Replacement steel bracket set for our Softail Aluminum fuel tanks. Can also be used for other custom fuel tanks. Includes steel brackets and rubber grommets. 711572 Tank mounting kit -030

Gas Tank Mounting Hardware RUBBER MOUNTS FOR SPORTSTER GAS TANKS These are exactly the same mounts as supplied with all our rubber mount Sportster tanks. Great for custom jobs or when you have lost one in your rebuild project. 345286 Rear mount with rubbers COLONY GAS TANK MOUNTING KITS High quality, show chrome tank mount hardware kits for Softail and Dyna models 91 to present.these kits include all bolts, nuts, studs and washers needed to mount the tank. 741833 Gas tank mounting kit 91 to present Dyna models 741832 Gas tank mounting kit 91 thru 99 Softail models 741834 Gas tank mounting kit 2000 to present Softail models ANTI-VIBRATION GROMMETS Install in the tank mount holes on Fat Bob tanks to stop the solid vibration that cracks the tank mounting flanges. Also for many Custom applications (pack of 10). 358074 Anti vibration grommets 345287 Front mount with rubbers CUSTOM GAS TANK INLET Weld in gas tank inlet, usable when buil-ding your own Custom made gas tank or as replacement for worn out connectors. Takes any of our vented cam-lock type gascaps. 011352 Tank inlet LOWER FRONT MOUNTING BRACKET FOR FAT BOB TANKS An exact reproduction of the lower bracket as featured on the 4 Speed frames thru 84. Easy to weld on and can be adapted to many Custom frames. Restores original looks and enables you to use Fat Bob tanks when the original bracket was torched off. 012357 Front lower bracket MOUNTING KIT FOR FAT BOB TANKS Complete mounting kit, a must when installing OEM or Zodiac's Fat Bob tanks to Custom or original 4 Speed frames. Includes all necessary washers, spacers, bolts and nuts. 345127 Mounting kit for Fat Bob tanks UNIVERSAL FAT BOB TANK MOUNT KIT Uniquely designed mounting kit for Fat Bob tanks. A precise way to mount the OEM or aftermarket Fat Bob tanks to Custom or original frames that have the OEM mountings removed.allows you to locate the bracket for a visual check of the tank location on the frame and once the position is selected the whole bracket set can be welded in place. 012367 Quickmount kit for Fat Bob tanks RUBBER MOUNTS FOR FLATSIDE GAS TANKS Accurate reproductions of the Original Equipment parts used to mount the Flatside gas tanks on 4 Speed FX models from 85 thru 86, and all Softail models from 84 to present.pack of 6 (OEM 11447 and 5775). 358084 Rubber mounts -031

Gas Tank Mounting Hardware/Kreem Products MOUNTING HARDWARE KIT FOR ONE PIECE SOFTAIL GAS TANK A complete mounting kit to install a one piece gas tank on a Softail model. Same kit as supplied with our one piece Softail gas tanks. 346103 Mounting kit for Softail tank FLAT-SIDE FAT BOB MOUNTING KIT FOR CUSTOM FRAMES A complete mounting kit to install Flat-side Fat Bob tanks to a Custom frame. Black powder coated brackets, chrome fasteners, dash spacers, tank grommets and mounting instructions are included. 238327 Tank mounting kit for Custom frames KREEM TANK DEGREASER This safe biodegradable degreaser quickly removes protective oily coatings from the inside of new tanks. Recommended for use prior to Kreem Tank Seal and/or Kreem Tank Prep.Assures a clean oil free surface. Excellent as a general purpose cleaner and degreaser. Sold in 1 pint (568 cc) bottles. 232030 Kreem Tank Degreaser FLAT-SIDE TANK MOUNTING KIT FOR EARLY FRAMES An easy-to-install mounting kit, which makes it possible to mount the late style Flat-Side gas tank on your early style 4 Speed Big Twin frame. The rubber isolation will prevent the damage of leaking fuel by breaking welds. Kit comes complete with all brackets and necessary hardware. 011498 Flat-Side tank mounting kit for early frames FLAT-SIDE TANK MOUNTING KIT A complete mounting kit that can be used to update your existing Flat-Side tank mounts, or for use on newly constructed vehicles instead of purchasing the original parts. The beveled washers and mounting screws are chrome-plated. Fits 84 to present Softail, and all other models with split tanks from 85 to present. 345228 Flat Side tank mounting kit KREEM COMBO PACK The Kreem tank prep and sealer kit to create an excellent "tank within a tank". The advanced formula cures to a tough white skin which protects the inside of the tank from rust and corrosion. Resists leaded and unleaded gasolines, gasohol and octane boosters or fuel additives when used in recommended concentrations.available in a complete kit including the sealer and the tank prep, or separately. 232020 Kreem combo pack 232021 Kreem liner/sealer 232022 Kreem prep and cleaner KREEM TANK MASK You have a beautiful painted tank and now it is leaking.the solution is to use Kreem Fuel Tank Liner ZPN 232020. But how to keep the paint job as beautiful as it was? Here is the answer: Kreem Tank Mask. It is a water-based liquid mask that is easily applied to painted tanks and other painted surfaces. Paint it on, let it dry to a non-tacking film and you can use Kreem Fuel Tank Liner without causing damage to the paint job.when you are ready you can simply wash Kreem Tank Mask away with warm soapy water. Kreem Tank Mask is resistant to Kreem Fuel Tank Liner and Kreem Tank Prep and comes in 8 fl.oz. (285 cc) bottles, usually enough for a motorcycle fuel tank. 232031 Kreem Tank Mask -032

Petcock CHROME PETCOCK These petcocks are highly polished and than chrome plated, a real "Wannahave" for each custom builder with eye for detail. Petcocks are designed to maximize fuel flow in both main and reserve modes. Feature 22 mm metric petcocks fit all 75 to present Big Twin and Sportster models as well most Custom tanks. 022600 Left side single outlet 022601 Right side single outlet 022602 Downward single outlet NESS GAS VALVES Gas valves, also known as fuel valves or petcocks Hi-flow, smooth styled and chrome plated Positive lever action Economically priced A07030 Vertical outlet A07031 Rear outlet A07032 Forward outlet ACCEL HIGH-FLOW FUEL VALVES The Accel "High Flow Fuel Valve Kits" feature a 100 micron screen filter, on/off and reserve positions packaged into a show chrome quality housing. This makes the Accel High Flow Fuel Valve Kit an easy cure for high RPM fuel starve that can cause detonation and eventual engine failure. Accel recommends the installation of a high flow valve with any modification to your motorcycle that increases RPM and acceleration, such as air filter, exhaust, camshaft etc. Available with straight down spigot or side spigot with a 180 degree swivel. Fits most models 71 to present. SHUT-OFF VALVE EXTENSION KNOB Allows easier operating of the old style shutoff valve, as used on the 40 thru 66 models. 032448 Extension knob 233821 With 180 degrees rotatable side spigot SHUT-OFF VALVE FOR EARLY FAT BOB TANKS Very precise reproduction of the Big Twin 47 thru 66 tank shut-off valve. This completely assembled unit comes with rod, cap knob, all washers, seals and hardware. Can also be used on 45CI models but changes the reserve capacity. 711854 Shut-off valve TANK CONNECTOR LINE FOR EARLY FAT BOB TANKS Crossover gas line for Fat Bob Tanks. Fits 48-65 FL models, has chrome finish (OEM 62355-48). 012251 Tank connector line 2337 With straight down spigot OLD STYLE PETCOCK This chrome plated Harley style petcock fits early Harley and most Custom gas tanks with 3/8" NPT internal connector (OEM 62125-55B). 011170 Old Style Petcock -033

Petcock PETCOCKS WITH NUT CONNECTION Disc type petcocks with mesh filter screen. Come with 13/16" chrome nut. Available with straight down spigot, right side spigot, and left side spigot.fits OEM tanks 75 thru 82, and most custom tanks with external 13/16" connection. REPLACEMENT SEALS FOR DISC TYPE ZODIAC PETCOCKS These Viton seals fit behind the face plate of all Zodiac disc-type petcocks. They solve the problems associated with various types of fuels available today, including the (lead free) Ethanol-type gasoline.available with 4 holes for old-style petcocks and with 3 holes for the newer type petcocks. Sold in 10-packs. 011415 Viton gaskets, 4 holes 011494 Viton gaskets, 3 holes PETCOCKS WITH EXTERNAL THREAD With 90 degrees spigot, fits all pre 75 gas tanks and Custom tanks with 3/8" NPT internal connector (disc-type) or with straight spigot,fits all pre 75 gas tanks and Custom tanks with 3/8" NPT internal connector (OEM 62125-55B) (disc-type). 011407 90 Degrees 011409 Straight 011401 Straight down spigot, fits 75 to present PETCOCKS WITH BRASS FILTER With 90 degrees spigot, fits 75 to present (disc-type) or with straight spigot, fits OEM and Custom tanks 75 to present (OEM 62163-75) (disc-type). 011403 Left side spigot 011405 Right side spigot 011413 90 Degrees 011411 Straight CHOPS 76 PETCOCKS These great looking petcocks are a perfect example how Italian design can add a classy touch of style to your American machine. Available in chrome plated aluminum with left or right exit. Fits all stock and aftermarket gas tanks with male 22 mm connection. 743428 Chrome, left exit 743436 Chrome, right exit -034

Petcock PINGEL ROUND KNOB HIGH FLOW PETCOCK Featuring the same high flow body as the "Designer" petcock ZPN 236300. Although they have the same chromed body, this petcock is equipped with a round knob to control the ON, RESERVE and OFF positioning. Input via 22mm connector, including adapter nut. Output via 5/16" hose barb, left side. 744251 Round knob petcock PINGEL VACUUM FUEL VALVE Finally a high performance direct OEM replacement vacuum operated fuel valve.this vacuum operated fuel valve has the highest fuel flow of any vacuum style fuel valve on the market. These fuel valves have the same safety feature as an OEM. When the valve is left in the "On" position, with the motor off, the fuel flow will be shut off automatically. These valves feature a high quality, lustrous chrome finish. Pingel Vacuum Fuel Valves are available in H-D Metric with Adapter Nut. 741226 Left side mount hose outlet facing forward 741227 Left side mount hose outlet facing to the rear 741228 Left or right side mount hose outlet down PINGEL POWER-FLO' HIGH VOLUME PETCOCKS These petcocks have all the features of the standard Power-Flo' petcocks with the exception that they are specially designed for use with the 75 to present Original Equipment gas tanks. They have a more compact installation saving around 1/4" installed height over the standard Power-Flo'.Available in polished aluminum and chrome plated finish. Single outlet Polished Chrome 236330 236331 Forward 236332 236333 Backwards 236334 236335 Side 236336 236337 Under Race petcock Dual outlet facing under motorcycle Polished Chrome 236338 236339 With reserve 236340 - Without reserve -035

Petcock PINGEL "DESIGNER" HIGH FLOW PETCOCKS These "Designer" petcocks are manufactured from solid brass to very strict specifications and tight tolerances. Bodies are highly polished and than chrome plated and are available with either smooth or machined designs. Pingel Petcocks are the ultimate choice for the Custom builder with an eye for detail.they come in smooth, grooved, light Stripes, Diamond or Flamed design.the inside of these high volume petcocks have the same features as Pingel's Power Flow' petcocks.the unique design maximizes the fuel flow on both main and reserve. Petcocks are available for all model Big Twin and Sportster late and early gas tanks.the 22 mm metric petcocks fit all Big Twin and Sportster 75 to present. The petcock with 3/8" NPT thread fits pre-75 as well as fit most Custom gas tanks.all models petcock are available in forward, backward or down outlet Designer petcock with 22 mm thread. Fits all Sportster and Big Twin models 75 to present Forward (A) Backwards (B) Side (C) 236300 236310 236320 Smooth 236301 236311 236321 Grooved 236302 236312 236322 Lightning 236303 236313 236323 Diamond 236304 236314 236324 Flamed Designer petcock with 3/8" NPT thread Fits all pre-75 models and most Custom gas tanks Forward (A) Backwards (B) Side (D) 236305 236315 236325 Smooth - 236316 - Grooved - 236318 236328 Diamond -036

Petcock PINGEL POWER-FLO' HIGH VOLUME PETCOCKS These high volume, high performance petcocks are manufactured in the U.S.A. by Pingel Enterprises.The unique design maximizes fuel flow on both main and reserve making the Power-Flo' petcock unequalled in fuel flow by any other petcock manufactured for a motorcycle. All petcocks are available with an easy twist lever and offer more reserve than stock gas valves. These Power-Flo' petcocks feature a polished aluminum or chrome plated brass body of 1 1/8" hex with a total length from bottom of the threads to the bottom of the valves of only 1 1/4". This ultra compact size permits their installation in even the tightest clearances. The machine cut 3/8" NPT threads of the valve body fits stock gas tanks thru 74 as well as most aftermarket Custom tanks. The optional adapter nut permits installation on the 75 to present Original Equipment, Zodiac and most other after market gas tanks. High quality o-rings insure leak proof seal. Stainless steel components with stainless steel fuel screen are included. The dual outlet version can be used for Nitrous Oxide systems (one outlet for carburetor/fuel pump feed and the other as a fuel return from the fuel pump). 234400 Single outlet 90 degr. aluminum 234401 Single outlet 90 degr. chrome 234403 Single outlet down, aluminum 234404 Single outlet down, chrome 234402 Dual outlet, aluminum 234405 Adaptor nut, permits installation on OEM or aftermarket gas tanks with 7/8" or 22 mm male tank bung, chrome finish PINGEL FUEL VALVE ADAPTER FOR 35 THRU 65 STYLE SPLIT GAS TANKS Pingel's stainless steel fuel valve adapter offers better flow and still retains the stock crossover connection on 35 thru 65 two-piece gas tanks.in conjunction with a 22 mm Pingel Power-Flo or Guzzler fuel valve this will drastically improve fuel supply. A must on tuned and especially today's high performance engines as the stock fuel valve set up simply can not cope with their fuel demand. 744249 Pingel Big Twin fuel valve adapter PINGEL OLD SKOOL STYLE BRASS PETCOCKS Pingel's Old Skool style fuel valves feature the same internal design as all their other fuel valves. This design maximizes fuel flow on both main and reserve. Made from solid brass with a high luster polished finish for that classic appearance.available in 3/8 NPT for use on pre-75 and most custom gas tanks and 22 mm for use on 75 to present style gas tanks. 744258 Pingel 3/8 NPT brass fuel valve 744259 Pingel 22 mm brass fuel valve PINGEL ELECTRO-FLO FUEL VALVE Pingel's Electro-Flo fuel valve offers a unique feature as it will not allow the motorcycle to start unless the valve is in the On-position.The result is no more forgetting to turn the fuel on, starting the bike, and taking off only to have the bike kill because it has run out of fuel.the Electro- Flo fuel valve utilizes Pingel's "Guzzler" impressive 211 oz. (over 6 Liter!) per minute flow rate along with outstanding race-tested durability. Available with 22mm or 3/8" NPT fitting, both featuring a 5/16" (8 mm) hose fitting. The Electro-Flo is made from solid billet aluminum and has a high luster polished finish. 744256 Electro-Flo fuel valve, 22 mm fitting 744257 Electro-Flo fuel valve, 3/8 NPT fitting -037

Petcock PINGEL IN-LINE FUEL VALVE Pingel designed this in-line fuel valve with the Custom bike builder in mind, giving you a chance to express your creativity without worrying about the fuel valve location. The valve uses a simple on/off operation without a reserve capacity and without a fuel filter. Has a chrome finish. 744250 In-line fuel valve PINGEL FUEL INJECTION CONVERSION When you want to convert your carbureted engine to fuel injection this is what you need. A conversion adapter designed to supply fuel to a fuel injection system with one outlet, while returning fuel to the tank with one inlet. The manifold has a 22 mm connection and is chrome plated. 744254 Pingel Fuel Injection conversion 22 mm KUSTOM TECH IN-LINE FUEL VALVE Fuel valve, also known as petcock. This Kustom Techs fuel valve is made in Italy from solid brass. It is fitted in-line in your fuel line. Has a polished finish. Gives your fuel tank an extra clean look and the impression you don't have a petcock at all. Only has two positions; open or closed. NO reserve! 751189 Kustom Tech in-line fuel valve PINGEL FUEL VALVE ADAPTERS FOR FUEL INJECTION TO CARBURETOR CONVERSIONS To convert 95 thru 2001 fuel injected FLH/FLT series models to a carburetor system you need an adapter to fit a fuel valve to the stock gas tank. Because of the tight tolerances these adapters can only be used with our Pingel high flow fuel valve. These adapters are available for bikes that were originally fitted with either Magneti Marelli or Delphi fuel injection. Fuel valve must be ordered separately. 744252 For 95 thru 2001 FLH/FLT series models originally equipped with Magneti Marelli fuel injection 744253 For all 2002 to present models originally equipped with Delphi fuel injection PINGEL CHOPPER VALVE The Pingel Chopper Valve has been designed for use on motorcycles that have custom fuel tanks that are raised high in the front. This style of fuel tank usually does not allow proper fuel pick up when using a standard petcock with reserve position. Pingel's Chopper Valve allows the builder to keep the bottom of the tank clean from fuel lines.the custom builder now has universal options for mounting the fuel valve by utilizing the mounting holes on the back of the valve.this fuel valve has smooth clean lines featuring a compact design measuring 1-1/2" (38 mm) high x 2" (51 mm) long x 1 3/8" (35 mm) deep. There is an easy to operate position selector knob with a ball detent for positive On-Off-Reserve locating. All hose barbs are 5/16". The Chopper Valve will require two hoses to be routed from the fuel tank-one for the ON position and one for the RESERVE position. The Chopper Valve is designed for exceptional fuel flow to feed the thirstiest of big inch engines. CNC machined from a solid piece of billet brass and finished with lustrous show quality chrome. 744255 Pingel Chopper fuel valve SPORTSTER FUEL INJECTION TO CARBURETOR CONVERSION Pingel's Fuel Injection to Carburetor Conversion Fitting Kit allows you to convert your Electronic Fuel Injection equipped Sportster to a carburetor system. This kit replaces the factory tank fittings allowing the use of the separately available high quality high flow Pingel 1/4 NPT Fuel Valve, also known as petcock, to feed the carburetor of your choice. Conversion fitting is machined from billet stainless steel, Fuel Valve machined from billet aluminum. 744268 Sportster EFI to carburetor conversion fitting kit 744295 Pingel Aluminum 1/4 NPT Fuel Valve, rear outlet -038

Petcock/Fuel Pump/Fuel Filter FUEL VALVE O-RINGS Viton O-rings as fitted between the fuel valve and tank adapter on 2002 thru 2006 Big Twin and Sportster. Genuine James. Sold in dealer 5-packs. 742488 Viton O-ring, 5-pack (OEM 62712-02) S&S FUEL PUMP KIT Customizing a fuel injected bike can be a real agony.where to find a cool tank that can hold an OEM style fuel pump. This smart design fuel pump kit from S&S helps you out. Due to its small dimensions it can be fitted in nearly any stock or aftermarket fuel tank. The capacity of 67 ltr per Hour, while boosting a pressure of 4 bar/55 PSI, is well within needs for most bikes.the pump is secured by hollow mounting bolts. The bolts provide an outlet for wiring and pressurized fuel.a fiber media filter, placed at the lowest point in the tank prevents contaminants from damaging the pump or clogging fuel injectors. The kit includes the fuel pump, inlet hose, filter, hardware and complete mounting instructions. 750862 S&S Fuel pump kit RSD "GAS-IT" FUEL INJECTION KIT Designed by Roland Sands Designs, this fuel injection kit uses the OEM Harley-Davidson EFI components to relocate the fuel pump, regulator and filter to the underside of the gas tank. This opens up endless possibilities for you Custom job.the stainless steel weldin tank part measures 3 3/4" x 8" (9.5 cm x 20.3 cm). Tank bottom must be relatively flat to accommodate port installation. Custom fabrication required. Kit comes with weld-in steel manifold and fasteners. 740630 Gas it fuel injection kit only If you start from scratch you will also need 740766 Fuel pressure regulator (OEM 27408-01) 740767 Fuel filter with clamps, O-ring and hose (OEM 61001-01) 740768 Fuel sender kit (OEM 75300-05) 740769 Fuel pump assembly (OEM 62897-01B) 740770 Check valve assembly with O- ring (OEM 62189-01A) FUEL LINE "T" JUNCTION Provides maximum flow, durable, light weight, and is easy to use. One size fits all fuel lines with 3/16" to 3/8" inside diameter (4.7 mm to 9.5 mm). Sold in a shop pack of 12. 233792 Fuel Line T VACUUM VALVE BY-PASS KIT Vacuum operated petcocks are often leaking or give a poor fuel flow.with this by-pass kit you can easily prevent these kind of problems. Kit contains a petcock backing plate plus gasket and a vacuum hose plug, will fit most vacuum operated petcocks. 237352 Vacuum valve by-pass kit FILTER ELEMENT FOR PINGEL INLINE FUEL FILTERS Replacement bronze filter elements for the Pingel In-Line fuel filters. Filters down to 10 microns in size and is for use for fuel injection only. Comes with O-ring included. 234413 Filter element bronze PINGEL IN-LINE FUEL FILTERS These American made polished aluminum High Performance fuel filters flow more fuel than most other filters.weights only 3 ounces and has the ability to flow up to 51 ounces per minute. The 2-piece billet aluminum housing supports a pleated re-cleanable lifetime stainless steel element which filters down to 40 microns in size, yet does not permit any restriction of fuel flow. The body length of these filters is only 1 1/8" (30 mm). Filter fits 5/16" (8 mm) inside diameter fuel line. 234408 Pingel In-line fuel filters -039

Fuel Filter/Fuel Catalyst/Gas Gap & Cover CHROME ALUMINIUM BILLET FUEL FILTER 2-piece lightweight chrome plated billet filter. Features a washable filter screen and spigots that will take 5/16" (8 mm) inside diameter fuel line. Body length is 1 1/2" (38 mm) and an outside diameter of 1 3/16" (35 mm). 120083 Chrome Billet fuel filter GAS CAP GASKETS Thick gas cap O-ring gasket for screw on type gas cap as used on most models 82 to present (OEM 61109-85). 231147 Gas cap gasket, thick DELUXE CHROME GAS CAP Die-cast show-chromed gas caps, available with and without vent. The vented gas cap fits Fat Bob style R/H tanks and all OEM single cap tanks aswell as most of our Custom gas tanks. The not vented gas cap fits Fat Bob style L/H tanks. 011221 Gas cap vented 011222 Gas cap not vented FITCH FUEL CATALYST Most fuel is made up of high-energy constituents, which burn with a fairly high degree of efficiency. However, in addition to these high-energy fuel constituents, there are others, which tend to cause problems during the combustion process.these are the lighter components, which burn too fast at the beginning of the combustion process causing pre-ignition and the heavier ones, which burn too slowly at the end of the process causing both excessive smoke and carbon buildup. The Fitch Fuel Catalyst acts on both of these problem fuel components, insuring that they burn with the same efficiency as the rest of the fuel.all forms of Power Sports equipment such as motorcycles,atv's, snowmobiles and personal watercraft can benefit from the Fitch Fuel Catalyst. Once the Fitch Fuel Catalyst is installed the treated fuel will begin to burn more completely resulting in a cleaner, better running engine that will start easier, burn less fuel and increase power and performance. The Fitch Fuel Catalyst helps keep your fuel fresh during the off-season and eliminates the need for stabilizers and other additives. The fuel catalyst is warranted for 350.000 km or 5.000 operating hours, effectively the life of your engine.comes in a package of two for both single and dual tankhalve applications. 700895 Fitch Fuel Catalyst GAS CAP GASKET Available in both thin and thick.thin one fits all U/UL/E/EL/ and FL/FLH gas caps 37 thru 76, thick gasket fits all camlock gas caps 77 to present. Sold in 10 packs. 234483 Gas cap gasket thin (OEM 61114-48) 234482 Gas cap gasket thick (OEM 61111-77) CHROME GAS CAPS Vented fits all Single cap and R/H double cap Harley and our Custom tanks. Non vented fits all L/H double cap Harley and our Custom tanks. 011152 Original style, vented 011179 Original style, non vented (OEM 61103-65) CHROME PLATED VENTED GAS CAP WITH LONG SKIRT The extra long skirt on this gas cap completely covers the filler neck of your gas tank, providing a clean Custom look. Fits single or vented side of all OEM type gas tanks with cam lock gas cap as well as many Custom gas tanks. 011438 Chrome extra long skirted gas cap CHROME LATE STYLE SCREW-IN GAS CAPS Chrome finished, plastic bodied, nylon threaded gas caps.designed to fit the OEM as well as all Zodiac tanks with screw type filler neck 82 to present. 011182 Vented, fits right side of twin cap tanks and all single cap tanks except FLT(C), FLHT(C) (OEM 61102-83A) 011183 Non vented, fits left side only (OEM 61103-83) -040

Gas Gap & Cover RSD GAS CAPS & FUEL GAUGE REPLACEMENT CAPS Roland Sands has packed as much style as he could into his RSD gas cap line. Each design is unique and with over a dozen to choose from, there is sure to be one to match your style. They come as crew-in style vented gas caps that fit all models 96 to present or as a Dummy Cap to replace the stock fuel gauge or as a LED indicator cap. This is a direct replacement snap-in cap to replace the left side OEM fuel gauge with a built in Low Fuel LED light built in. The light is user programmable to any pre-set fuel level. Except for the Vintage design these caps come with an interchangeable RSD logo in contrast cut black or black and brass. Available in chrome, RSD's exclusive Black OPS or Contrast Cut black. Vented gas caps Chrome Black OPS Contrast Cut 740877 740878 740876 Café 740880 740881 740879 Gear Drive 740883 740884 740882 Tech 740886 740887 740885 Tracker 740624-740625 Vintage Fuel Gauge replacement caps Chrome Black OPS Contrast Cut 740863 740864 740862 Café 740866 740867 740865 Gear Drive 740869 740870 740868 Tech 740872 740873 740871 Tracker 740875-740874 Vintage LED Fuel level indicator Caps Chrome Black OPS Contrast Cut 752031 752032 752030 Café 752034 752035 752033 Gear Drive 752037 752038 752036 Tech 752040 752041 752039 Tracker 752043 752044 752043 Vintage -041

Gas Gap & Cover SPINNER GAS CAPS FOR SCREW- IN STYLE GAS TANKS These chrome plated spinner gas caps fit all screw-in style gas tanks with single-bung, or on the right side of tanks with dual screw-in style bungs. 012008 Chrome spinner gas cap NESS LOW GRAVITY SCREW-IN GAS CAPS Low profile design is available in twelve different styles All chrome-plated billet aluminum caps measure 1/4" to 3/8" tall Exclusive ratcheting design provides proper torque and design alignment Early screw-in gas caps fit all models 82 thru 96 Late screw-in gas caps fit all models 97 to present "Dummy" gas caps replace the fuel gauge style gas caps found on some late Big Twin Models Vented gas caps have right-hand thread; non-vented have left-hand thread All gas caps are sold each 82-96 82-96 97-up 97-up Vented Non-vented Vented Non-vented Dummy A07152 A07153 A07252 A07253 A07167 A Baby Moon A07150 A07151 A07250 A07251 A07166 B Peaked A07156 A07157 A07256 A07257 A07169 C Grooved A07158 A07159 A07258 A07259 A07170 D Flamed A07181 A07182 A07281 A07282 A07183 E Scalloped - A072 - - - F RAD-II CHROME POINTED SCREW-IN GAS CAP Chrome finished pointed gas caps. Fits 82 to present fuel tanks with screw type filler neck.available as a set of a vented and a nonvented cap for use on Big Twin models, or as a vented cap only for use on Sportster and other models with a single gas cap. 022071 Chrome pointed gas cap, vented 022072 Chrome pointed gas cap set "EAGLE SPIRIT" GAS CAPS These screw style gas caps will fit 82 to present tanks. Available as set or separate (vented or non vented) in Chrome finish. Vented gas cap will also fit single cap tanks (except FLH/FLHT/FLHS). 011432 Gas cap set, chrome finish 011433 Gas cap vented, chrome finish 011434 Gas cap non vented, chrome finish -042

Gas Gap & Cover LOCKABLE SCREW-IN GAS CAPS Lockable gas caps with ribbed sides and show quality chrome finish. The lock system prevents for the gas caps coming loose with the engine running. Fits all 82 to present fuel tanks with Screw-In style caps.the vented version fits on models with a single gas cap, as well as on the right side on models with dual gas caps.the non-vented version fits on the left side of models with dual gas caps. Vented and non-vented caps are sold in sets as well as individually. 0122 Set of left and right caps 0120 Vented lockable gas cap only 0121 Non-vented lockable gas cap only LIVE TO RIDE GAS CAP COVER Self-adhesive, chrome plated gas cap cover with Eagle-Spirit logo. Fits late style Screw-In gas caps (except molded plastic). 301729 Eagle Spirit gas cap cover adhesive SATELITE GAS CAP COVER Chrome plated die-cast gas cap cover fits 77 thru 83 gas caps, except screw-on type gas caps. 011157 Satelite gas cap cover CHROME CAM LOCK STYLE GAS CAPS Stock replacement cam lock style gas caps as used from 36 thru 82, also fit most Custom and aftermarket tanks with cam style bungs. Vented caps are used on single cap gas tanks, and the right side on dual cap gas tanks. Non-vented caps are used on the left side of dual cap tanks. Fits 36 thru early 73 Big Twin, and 57 thru early 73 KH and Sportster 0190 Vented (OEM 61103-36) 0191 Non vented (OEM 61103-65) Fits late 73 thru 82 Big Twin and Sportster, except FLT and FXR models 0193 Vented (OEM 61102-73A) 0194 Non vented GAS CAP COVER Die-cast and beautifully chrome plated. Available in three sizes. Small ones fit Harley gas caps up to 76. Our universal gas caps and many original gas caps as used on various makes and models. Large ones fit Harley 77 thru 83. Extra Large fits Harley screw-on gas caps 82 to present. 011154 Krommet cover Small 011155 Krommet cover Large 011161 Krommet cover Extra Large CHROME BILLET POINTED OR DOMED "ESSENTIAL" GAS CAPS These gas caps have a unique ratchet action to prevent over tightening and come complete with a paint protector and locking tool with key ring.the right hand side cap is fitted with an EPA check valve, which can be removed for service or other applications. Made from solid billet aluminum with a show chrome finish. "Essential" gas caps fit all models with screw-in style gas caps 82 to present, as well as all Zodiac gas tanks with screw type filler neck.available as sets of left and right, as well as single gas caps for use on single-cap gas tanks, such as used on Sportster models. Pointed or Domed style. 012156 Pointed gas cap set with left and right side caps, paint protectors and locking tool 012155 Pointed gas cap with paint protector and locking tool, vented 012158 Domed gas cap set with left and right side caps, paint protectors and locking tool 012157 Domed gas cap with paint protector and locking tool, vented -043

Gas Gap & Cover IGNITION SWITCH AND LOCKABLE SCREW-IN GAS CAP KITS Handy kits with an ignition switch and lockable gas caps reduce the number of keys on your ring as one key fits both the gas caps, as well as the ignition switch. The lockable gas caps with ribbed sides and show quality chrome finish.the lock system prevents for the gas caps coming loose with the engine running. Fits all 82 to present models dual Screw-In style caps, except those with a fuel level gauge.available in your choice of mechanical or electronic ignition switch. 0124 With 6 post mechanical ignition switch 0123 With 6 post electronic ignition switch STROKER STYLE FLUSH MOUNT GAS CAPS These slick lookin' Flush Mount gas caps have that sought-after appearance of Aero-style gas caps.they fit all models 82 to present and have a perfect show chrome finish. Easy to install, just screw the built-in trim ring straight into your tank.the Allen head screws are real but not used to secure the trim ring. The no-key filler plugs feature a ratchet mechanism to avoid that you tight them so good that it will be a pain to open them again. Order a vented version for models with a single gas cap or a vented and a non-vented version for models with dual gas caps.a dummy gas cap to replace the fuel gauge as mounted on many models in the left gas tank is also available. 012056 Non-vented, right hand thread 012057 Vented, right hand thread 012058 Non-vented, left hand threat 012061 Matching dummy cap FLUSH MOUNT GAS CAPS Chrome plated or black anodized gas cap, can be used as stock replacement for 82 to present models with screw in type gas caps. Vented and non-vented caps are sold in sets as well as individually. For customizers we offer a vented weld in cap, which comes complete with a steel bung.to refill your tank you have to open the cap with a special tool supplied with the kit. We even managed to give this tool a little CNC machine treatment so now you can open your beer bottle too! 012031 Chrome gas cap with weld-in bung 012032 Chrome vented gas cap 012065 Black vented gas cap 012033 Chrome non-vented cap 012034 Set with a chrome vented and a chrome non-vented cap 012067 Set with a black vented and a black non-vented cap VIPER STYLE FLUSH MOUNT PAINT PROTECTOR GAS CAPS These slick lookin' Flush Mount gas caps have a perfect show chrome finish. Easy to install, just screw into the stock opening on your tank. The no-key filler plugs features a ratchet mechanism to avoid that you tight them so good that it will be a pain to open them again, whilst the screw-in style base remains on your tank and functions as a paint protector.. Available for use on most models from 82 to present A dummy gas cap to replace the fuel gauge as mounted on many models in the left gas tank is also available. 012080 Chrome Viper gascap R/H vented 012081 Chrome Viper gascapset L/R 012082 Vented gas cap with built-in check valve for late 96 thru 2003 Sportster and right side on late 96 to present Softail, Dyna and Touring 012084 Dummy cap to replace fuel gauge -044

Gas Gap & Cover/Gas Tank/Gas Gap & Cover/Gas Tank/Gas Gap & Cover "POP-UP" CUSTOM GAS CAPS These "Pop-Up" gas caps allow you to give your gas tank that real Custom Smooth Top look, as seen by the worlds leading Custom Bike Builders.They are easy to open or close, just push in the cap, twist and the cap will pop up and is ready to unscrew. No matter if you have a steel or aluminum gas tank, Zodiac has these Custom goodies with your choice of aluminum or steel weld-in bung. Caps are vented and available in aluminum with a top-quality show chrome finish or natural aluminum to apply the finish of your choice. Bungs have a 2 5/16" (59 mm) outer diameter, caps are 55 mm in diameter. 0100 Natural aluminum cap with weld-in steel bung 0101 Natural aluminum cap with weld-in aluminum bung 012100 Natural aluminum cap without bung 0102 Chrome plated aluminum cap with weld-in steel bung 0103 Chrome plated aluminum cap with weld-in aluminum bung 012101 Chrome plated without bung POP-UP SCREW-IN STYLE GAS CAPS Super sleek looking domed gas caps that fit straight into stock 82 thru 95 and 96 thru 2009 gas tanks. Just push and turn the inner cap a quarter with your thumb and the knurled part pops up, allowing you to screw or unscrew the complete cap.these chrome eye catchers are available in sets with one vented and one non vented cap for Big Twin models, as well as a single vented cap for use on Sportster models. 012076 Set of left and right, fits 82 thru 95 Big Twin models 012077 Set of left and right, fits 96 thru 2009 Big Twin and Twin Cam models 012078 Single cap, fits 82 thru 95 Sportster 012079 Single cap, fits 96 thru 2009 Sportster "POP-UP" STOCK REPLACEMENT GAS CAPS Now you can have that real Smooth Top look, as seen by the worlds leading Custom Bike Builders without changing your gas tank. These "Pop-Up" gas caps come complete with threaded inserts that replace the stock gas cap and allow for the use of these chrome plated Pop- Up's. Just remove your stock gas caps and install the inserts in seconds! "Pop-up" gas caps are easy to open or close, just push and twist the cap and the cap will pop up and is ready to unscrew. Fits all screw cap type stock OEM and most aftermarket gas tanks. Caps are available in vented and non-vented and are sold each. 0104 Vented pop-up gas cap, chrome 0105 Non-vented pop-up gas cap, chrome LATE STYLE CHROMED STEEL THREADED GAS CAPS These beautifully chrome plated late-style steel gas caps are perfect reproductions of the original equipment part.these caps come with the latest low-pressure relief vent properly recessed in the cap to clear the filler neck vent tube on 85 to present gastanks. 011546 Right side cap, vented (OEM 61102-83A), also fits single cap models, except FLT(C) & FLHT (C) 011547 Left side cap, non vented (OEM 61103-83) -045

Gas Gap & Cover CHROME BILLET "ESSENTIAL" GAS CAPS These gas caps have a unique ratchet action to prevent over tightening and come complete with a paint protector and locking tool with key ring. The right hand side cap is fitted with an EPA check valve, which can be removed for service or other applications. Made from solid billet aluminum with a show chrome finish."essential" gas caps fit all models with screw-in style gas caps 82 to present, as well as all Zodiac gas tanks with screw type filler neck. 012026 Gas cap set with left and right side caps, paint protectors and locking tool 012028 Gas cap set with right side cap, and left side dummy cap to replace stock left side fuel gauge assembly, paint protectors and locking tool 012027 Left side dummy gas cap to replace stock left side fuel gauge assembly, paint protector and locking tool 012029 Right side gas cap with paint protector and locking tool, vented 012030 Left side gas cap with paint protector and locking tool, non-vented CHOPS 76 GASCAPS Chops 76 offers a complete exclusive range of so-called "Old School" motorcycle products, including these gas caps. A perfect example of Italian design. Produced on state of the art machinery from high quality materials, your guarantee for products that meet the highest quality standards.we offer four lines of Chops 76 gas caps in chrome or black anodized aluminum or polished-to-perfection pure brass. Gas caps fit 82 to present screw-in style fuel tanks. Arrow Line 743350 Chrome, vented 743351 Black anodized, vented PAINT SAVER GAS CAP This trick little part screws straight into any screw bung style tank from 82 to present Harleys as well as most aftermarket screw bung style gas tanks. The threaded 2 3/8" (6 cm) diameter outer bung is flush mounted in the tank and works perfectly as a paint saver. The small, only 1 1/2" (3.8 cm) diameter inner gas cap is opened and closed with the included key. Sold as vented cap only or in sets with a vented and a non vented cap. Gas caps are made of aluminum with a perfect chrome or black finish. 012040 Chrome vented paint saver gas cap 012068 Black vented paint saver gas cap 012044 Chrome paint saver gas cap set 012070 Black paint saver gas cap set King Line 743352 Chrome, vented 743353 Black anodized, vented 743354 Brass, vented -046

Gas Gap & Cover Tower Line 743355 Chrome, vented 743356 Black anodized, vented "MAGNUM.38 POLICE SPECIAL" STYLE BILLET ALUMINUM GAS CAP COVERS BY RBS Something really special are these.38" Police Special Style" gas cap covers, decorated with genuine cartridge cases. Caps are machined from a block of solid aluminum and install easily over your stock gas caps. They are secured with almost non visible Allen head set screws. You can have these covers in polished or black, but the cartridges stay the same. For that true finishing touch there are matching handlebar grips, risers, point covers, and SuperTrapp end caps available. 722270 Chrome.38 Special gas cap cover 722271 Black.38 Special gas cap cover Cone Line 743357 Chrome, vented 743358 Black anodized, vented "MAGNUM.38 POLICE SPECIAL" BILLET ALUMINUM FUEL GAUGE COVER BY RBS You can't do without this trick fuel gauge cover when you have installed the Police Special gas cap cover. Like the gas caps, these covers are filled with genuine cartridge cases. Cover is machined from billet aluminum and installs easily over the stock fuel gauge trim. Cover is secured with almost invisible Allen head set screws.available in black anodized. For those that want it all there are also matching handlebar grips, risers, point covers, and SuperTrapp end caps available. 722292 Black.38 Special fuel gauge cover -047

Gas Gap & Cover CRIME SCENE CHOPPERS' SPEEDSTER GAS CAPS The Speedster gas cap is a slick, flip-open vented cap that complements the post war Bobber styling.the Speedster cap is Crime Scene Choppers' modern take on vintage Indy race car hardware. You've seen it on signature bikes built by Chica, Paul Yaffe and Cyril Huze.The cap bolts to a weld-in boss that you can add to any tank.the cap has an 80 mm outer diameter and is available with stainless or brass hardware.weldin bungs are available separately in both steel and aluminum. 743308 Speedster gas cap, satin finish with brass hardware 743310 Steel weld-in bung for Speedster gas cap 743311 Aluminum weld-in bung for Speedster gas cap 743312 Replacement gasket and o-ring kit LOCKABLE QUICK CAM FLUSH MOUNT GAS CAPS Replacement lockable Quick Cam flush mount gas caps. Available as a set with one vented and one non-vented cap for tanks with dual Quick Cam gas caps, or vented cap for tanks with single Quick Cam gas cap. 011549 Lockable gas cap set (style D) 011551 Vented Quick Cam gas cap (style D) 743309 Speedster gas cap, satin finish with stainless hardware -048

Gas Gap & Cover DELUXE "CLASSIC STYLE" LOCKABLE GAS CAPS These "Classic Style" lockable gas caps feature ribbed sides and a special lock-cover for that special look.the lock cover will prevent any water or moisture to enter the tank through the key-hole. The Super-Chrome surface makes these gas caps real eye-catchers. They will not vibrate or spin loose with the engine running. The dual gas cap sets use the same key for both the vented and the non vented gas cap. Their superb quality is securely tested and stated by a TÜV approval. 237377 Set of left and right caps for Fat Bob style tanks 237378 Single vented capc ANODIZED EXTRA SMALL MINI "QUICK ACTION" FILLER CAPS These popular extra small mini "Quick Action" filler caps are available with the inner part anodized in 4 popular colors. You can choose the color that matches up with the color of your bike.anodized mini caps come without lock. 237430 Silver 237431 Black 237433 Red 237434 Blue Replacement parts 237687 Replacement fixing screws (6 pack) 237690 Replacement rubber gasket, 6 hole 237683 Replacement flange, 6 hole 237686 Replacement neck CYCLE KRAFT NEO-FUSION GAS CAPS Cycle Kraft Neo-Fusion gas caps are precision made by Ken's Factory from billet aluminum and available in a polished finish or black anodized with clear cuts. The 2 3/4" (70 mm) diameter gas caps feature a trick opening and closing mechanism and come complete with stainless steel allen screws to secure them to the separately available weld-in bung for steel or aluminum gas tanks. 747327 Neo-Fusion gas cap, polished 747328 Neo-Fusion gas cap, black anodized with clear cuts 747329 Steel weld-in bung 747330 Aluminum weld-in bung "MIDI QUICK ACTION" ALUMINUM RACING GAS CAPS A smaller version of the popular "Quick Action racing gas caps. The smaller diameter makes it easier to install them on split gas tanks. Like the larger caps these are also available with or without lock. Lockable caps are also available with vent hole.non vented caps can only be used on tanks with external vent hole. A. 237353 Gas cap, non vented B. 237354 Lockable gas cap, non vented C. 237359 Lockable gas cap, vented Replacement parts 237688 Replacement fixing screws, 6 pack 237689 Replacement composite gasket, 6 hole 237691 Replacement rubber gasket, 6 hole 237684 Replacement flange, 6 hole 237685 Replacement neck -049

Gas Gap & Cover/Gas Tank/Gas Gap & Cover EXTRA LARGE AERO STYLE ALUMINUM RACING GAS CAPS Associated with the Racing Industry, these Aero-style caps gained popularity under the Custom Bike Builders.These 500-series Aero style gas caps are non vented, available with or without lock and are 140 mm outer and 75 mm inner diameter. Come complete with required mounting hardware. 232130 Aero cap with lock, non vented 232136 Aero cap without lock, non vented CHROME PLATED AERO-STYLE ALUMINUM GAS CAPS Flush mount chrome plated aluminum racing style gas caps. Can be used as replacement on all steel Zodiac tanks with Aero-style gas cap. Can also be used on other Custom tanks with Aero-style gas caps.available with 95 mm and 120 mm outside diameter and in vented and non vented. Aero Gas caps with 95 mm outer diameter 011528 Gas cap set vented and non vented 011526 Gas cap vented 011527 Gas cap non vented Aero Gas caps with 120 mm outer diameter 011525 Gas cap vented 011539 Replacement gasket & O-ring "QUICK ACTION" ALUMINUM RACING GAS CAPS These racing type caps are widely used for racing applications but are getting more and more popular with Custom Bike builders. This all aluminum alloy Shaw Flush fitting cap assembly is available with or without lock and has a 2" opening to allow easy filling. Non vented models can only be used if a separate vent is available on the tank. A. 232153 Quick Action gas cap, non vented B. 232154 Quick Action gas cap with lock, non vented Replacement parts 237647 Replacement fixing screws, 8 pack 237692 Replacement composite gasket, 237693 Replacement rubber gasket, 8 hole 237694 Replacement flange, 8 hole 237695 Replacement neck -050

Dash & Dash Panel NESS DASH PANEL COVERS FOR ROAD KING Designed to fit 95 to present FLT and FLHR models CNC machined from 6061-T6 billet aluminum with a chrome finish NESS DASH INSERT & FUEL DOOR COVERS Fuel door covers and dash inserts add a touch of class to the dash area on Dresser models Machined from forged aluminum with a high quality finish Three designs to chose from Grooved A04136 Fuel door, fits 89 thru 2007 FLT A04138 Dash insert, fits 87 thru 2007 FLT, except Ultra Classic and Screaming Eagle A04139 RAD-II Scalloped A04137 Fuel door, fits 89 thru 2007 FLT A04140 Dash insert, fits 2006 thru 2007 FLHX A04130 Fuel door, fits 2008 to present FLT A04131 Dash insert, fits 2008 to present FLHT, FLT and FLHX Retro A04147 Fuel door, fits 89-2007 FLT A04117 Dash insert, fits 2006 thru 2007 FLHX A04142 Fuel door, fits 2008 to present FLT A041 Dash insert, fits 2008 to present FLHT, FLT and FLHX A04135 Grooved A04133 Stepped -051

Dash & Dash Panel NESS BILLET DASH COVERS FOR SOFTAIL Exquisite design offers the looks of a onepiece billet dash CNC machined from 6061-T6 billet aluminum with a chrome finish Selected models are also available with a liquid filled oil pressure gauge Oil pressure gauge equipped models are supplied with engine fittings Fits all Softail models except FXSTD Deuce and FXCW and FXCWC Rocker A04101 RAD-II, fits 96 thru 99 A04107 Smooth, fits 2000 to present Models with oil pressure gauge and fittings A04127 Grooved, fits 84 thru 95 A04126 Grooved, fits 96 thru 99 A04145 Replacement Dash Rubber ARLEN NESS TANK EXTENSION FOR TOURING MODELS This tank extension gives you the look of a sleek custom tank with no cutting, grinding, or welding. Just bolt it right on to your stock Road Glide or Street Glide tank. Constructed from high quality composite materials and oven cured to insure stability over a wide heat range. Each extension piece has hand placed fibers strategically located to provide maximum strength to weight ratio. Each piece is primed and ready to paint. Designed to fit 97 thru 2007 or 2008 to present FLHX, FLHT, FLT, FLTR Street Glide and Road Glide models. Will not fit FLHR Road King models. Note: Requires modification of the stock seat or the use of a custom seat. A04114 Fits FLHX, FLHT, FLT and FLTR 97 thru 2007 A04111 Fits FLHX, FLHT, FLT and FLTR 2008 to present A04129 Grooved, fits 2000 to present NESS BILLET DASH PANELS Two styles to choose from Softail models fit 96 to present, except FXSTD Deuce and FXCW and FXCWC Rockers-up FXDWG models fit 93 to present Dyna Wide Glides -052 A04102 RAD-II, fits 2000 to present Billet upper panel Grooved Flamed A04177 - Fits 96 to present Softail - A04174 Fits 93 to present FXDWG Billet lower panel Grooved Flamed - A04180 Fits 84 thru 99 Softail A04172 A04183 Fits 2000 to present Softail - A04182 Fits 93 to present FXDWG

Dash & Dash Panel PM FUEL DOOR COVERS FOR TOURING MODELS The popularity of customizing the FLH and FLT Touring models, also known as "Baggers", inspired Performance Machine to create a line of accessories specifically for these bikes. PM styling was applied to saddlebag latch covers, fuel doors, and speaker covers. Machined from billet aluminum and treated to PM's time tested chrome process, the Contour Fuel Door is the crowning touch to any well-dressed bagger. Available in Smooth and Fluted design with a chrome or black Contrast Cut finish. Matching saddlebag latch covers and speaker covers can be found elsewhere in the Zodiac Bikers Book. Fits FLH and FLT Touring models 92 thru 2007 743113 Smooth, chrome 743117 Fluted, chrome 743114 Smooth, black 743118 Fluted, black contrast cut Fits FLH and FLT Touring models 2008 to present 743115 Smooth, chrome 7431 Fluted, chrome 743116 Smooth, black 743120 Fluted, black contrast cut CYCLE KRAFT FUEL DOOR COVERS FOR TOURING MODELS Cycle Kraft fuel door covers are precision made by Ken's Factory from billet aluminum and available in a polished version or black anodized with clear cuts. Replaces the stock fuel door cover on all 2008 to present FLT series Touring models. 747323 Polished 747324 Black anodized with clear cuts CYCLE KRAFT DASH INSERTS FOR TOURING MODELS Cycle Kraft dash inserts are precision made by Ken's Factory from billet aluminum and available in a polished version or black anodized with clear cuts. Replaces the stock dash panel inserts on all 2008 to present FLH and FLT series Touring models. 747325 Polished 747326 Black anodized with clear cuts PAUL YAFFE'S BAGGER NATION DASH COVERS Like your Dresser? Wish it had a little more style and a little less bulk? Paul Yaffe felt the same way. So he fabbed up these sleek dashes to alter the looks of any FLH or FLT model. These fiberglass dashes are a direct replacement for your stock dash and can be cut to length as it has been made extra long to fit even on the longest stretch tank.dashes are hand laid and come with a rubber trim, hardware and instructions. Those for 86 and later models also include a really trick chrome billet pop-up gas cap. 745027 Fits Fuel Injected Touring models 95 thru 2007 745026 Fits Touring models 2008 to present -053

Dash & Dash Panel STASH-DASH FOR TOURING MODELS The Stash-Dash for Touring models is a way to clean up your Bagger's console area while simultaneously providing extra storage space. Direct replacement for the stock console and improves the profile of the gas tank. Incorporates the stock gas tank cap and storage box under a smooth hinged lid. Fits 97 to present Touring models.available in raw finish for custom paint or in a flawless chrome finish. 301608 Chrome stash dash 301609 Raw stash dash DASH PANEL EXTENSION Chrome plated cast aluminum dash panel extension that fills the gap between your dash and seat. Fits 83 thru 86 FXWG models and 84 thru 99 Softail models, as well as most models with aftermarket Fat Bob style flat side tank. 3057 Chrome aluminum tank panel DASH PANEL FOR FAT-BOB GAS TANKS Show-chromed and perfectly formed dash panel. Fits all FL and Wide Glide models up to 84. Covers the gap between the Fat Bob tanks. 301148 Dash panel plain 358073 Mounting rubber with clips (10 pack) BILLET DASH PANEL FOR ROAD KING This black beauty is CNC machined from solid billet aluminum and then black anodized. After this the grooves have been re-machined to give a nice highlighted accent. Dash panel takes the stock Speedo, warning light cluster and ignition switch. Comes complete with chrome mounting screws. Fits 2004 thru 2007 FLHR Road King models. 301511 Black billet Road King dash panel CHROME DASH PANEL EXTENSION FOR TWIN CAM SOFTAIL Add a custom touch to your fuel tank with this chrome plated cover that extends the stock chrome dash panel to the full length of the fuel tank. Fits all Softail models 2000 to present, except Deuce, Rocker, FLSTSB Cross Bones, Screamin' Eagle models and 2009 to present FLSTC. 3064 Dash panel extension (OEM 71283-01) DASH PANEL FOR FAT BOB STYLE GAS TANKS This show chromed dash panel will enhance the smooth looks of your Fat Bob style gas tank. Comes complete with black side trim. Fits late FX and Low Rider models 77 thru 84, as well as most aftermarket Fat Bob style tanks. 301051 Fat Bob dash panel -054

Dash & Dash Panel/Gas Tank/Dash & Dash Panel DASH PANEL FOR FAT-BOB GAS TANKS WITHOUT DASH HOLE Show-chromed dash panel for use when instrument housings are not mounted on tanks.fits late models FX and Low Rider 77 thru 84. 301054 Dash panel plain CAT-EYE DASH FOR FAT BOB TANKS Beautifully show-chromed dash with two lights. This dash is a perfect reproduction of Harley's early style Cat-eye dash. Fits 3.5 and 5 gallon Fat Bob tanks. 013064 Cat-eye dash 358022 Trim rubber only THREE-LIGHT DASH MOUNTING PLATE Includes a complete set of mounting hardware, wiring and sockets. Mounts our three-light dash to Fat Bob tanks (OEM 70934-59). 013068 Dash base CHROME DASH PANEL FOR FXR MODELS Beautiful chrome plated dash cover that fits 84 thru 94 FXR/FXRS models. 301096 Tank panel chrome CAT-EYE DASH MOUNTING PLATE FOR EARLY FAT BOB TANKS Base plate with hardware and wiring. Mounts Zodiac's Cat-eye dash (ZPN 013064) to early (36 thru 46) Fat-Bob tanks. 013066 Base Cat Eye dash THREE-LIGHT DASH FOR FAT BOB TANKS Chrome plated steel dash with three lights. Fits 3.5 and 5 gallon Fat Bob tanks.available for the large diameter cable driven FL style speedo's as well as the smaller diameter electronic driven speedo's as used on most models from 95 to present. Replacement lenses and trim rubber are separately available. 013062 Three-light dash for cable driven speedo 011658 Three-light dash for electronic driven speedo 358022 Trim rubber only 165124 Red lens only 165122 Blue lens only LOUVERED CHROME DASH PLATE This louvered dash panel is an addition to our line of louvered products such as louvered side panels, belt guards etc. Features a stamped steel construction with beautifully chrome-plating and comes with complete hardware. Fits all Softail models and 4 Speed FXWG models 83 to present. 301860 Louvered chrome dash plate CAT-EYE DASH MOUNTING PLATE Includes all mounting hardware, wiring and sockets. Mounts our Cateye dash to Fat-Bob gas tanks. 013070 Base for Cat Eye dash TWO-LIGHT DASH MOUNTING PLATE Includes mounting hard-ware, wiring and sockets. Mounts two-light dash to Fat-Bob tanks (OEM 70938-49). 013072 Base plate for 2 light dash -055

Dash & Dash Panel TWO-LIGHT DASH WITH BASE PLATE FOR FAT BOB TANKS Show-chromed two-light dash with base plate. Fits 3.5 and 5 gallon Fat Bob tanks. 013052 Two-light dash kit 358022 Trim rubber only 013055 Red lens only LATE STYLE DASH MOUNTING PLATE Complete dash mounting kit for Big Twin models from 68 thru 95 with cast style dashes (except FXDWG models). Kit includes all hardware and spacers necessary to fit both the standard early-style Fat Bob and the laterstyle Flat-Side tanks.also included are: circuit breaker clips, ignition switch mounting screws, three terminal studs and five light sockets with bulbs. Fits Zodiac dash cover (ZPN 301698) or OEM cast dash. 013082 Dash base kit for cast dashes HIGH BEAM INDICATOR LIGHT Original style, multi-piece high beam indicator lamp assembly with replaceable bulb. Fits as original equipment on FX models 73 and 74, as well as XL models 68 thru 73. Can also be used to replace the later one piece "throw-away" indicator lamp on 75 and later FX models (OEM 67891-68). 160107 High beam indicator light CHROME DASH FOR FXR MODELS Chrome plated replacement dash to fit most FXR models 82 thru 94 (OEM 61411-82, 61412-82 and61414-82). 301422 Dash cover REPLACEMENT SOCKET FOR STEEL DASH Replacement socket only (OEM 71156-47). 163018 Replacement socket LATE STYLE CAST DASHES These heavy-duty zinc die-cast dashes are beautifully chrome plated duplicates of their OEM counterparts. Complete in every detail, each dash also includes the lenses, light divider and trim rubbers. They may be installed on most 4 Speed frames and Softail models when the appropriate dash base is used. 301698 Fits all models from 68 301886 Fits all models with selfcanceling turn signals (except Dyna Wide Glide) from 91 to present (OEM 71241-91) Replacement parts 358200 Trim rubbers (pair) (OEM 71295-68) CHROME DASH FOR FX MODELS Fits all FX models with tank mounted instruments from 77 thru 84.Available in a chrome plated stamped steel version and a Heavy-Duty die-cast. Die-cast version has the same thickness and construction as the original equipment part. 301250 Die-cast dash cover only (OEM 71301-77) (trim rubber and mounting hardware are separately available) 301679 Stamped steel dash, includes trim rubber and warning light hole plugs for Custom applications when High-beam indicator/trip reset knob is not installed (OEM 71301-77T) 358023 Thick style tank-to-housing trim rubber only (OEM 61401-82) -056

Dash & Dash Panel DASH CENTER MOUNTING BOLT FOR HARLEY Will mount all FL dashes 41 thru 67 but can also be used on Custom applications where choke is not brought through dash (OEM 71067-47). 339006 Dash mounting bolt DASH LENS AND SUPPORT KIT FOR FAT BOB DASHES This is the most complete dash kit available, fits FL models 68 thru 84, FX models 71 thru 72, FXWG models 80 thru 86 and Softail models 84 thru 95. Kit includes indicator lenses (neutral, hi-beam and oil), lens support and retainer, mounting clips and screws (OEM 71143-75, 71144-75A, 71145-75, 71141-68, 71164-68, 71297-68 and 2630W). 301710 Lens & support kit CHROME DASH SLOT SIDE TRIM This part covers the slotted opening beneath the odometer reset knob on all 47 thru 67 two light and three light dashes of all original equipment and aftermarket dashes. 301759 Dash slot trim (OEM 71311-47) CHROME PLUGS FOR FX STYLE DASH Chrome plated hole plugs to blank off the holes on FX style dashes when High-Beam indicator light and/or trip reset knob are not installed. 301465 Fits High-beam indicator light hole (10 pack) 301467 Fits trip reset knob hole (10 pack) DASH/SPEEDO MOUNTING KIT Complete mounting kit, to mount FX tank mounted dash and gauges on pre-85 3.5 or 5 gallon Fat Bob tanks. Exact reproduction of stock pieces. Includes speedo and tacho cup brackets, hardware and correct rubber mounts. 011215 Dash/Speedo mounting kit DASH SCREW KIT Chrome plated allen screws to mount the dash on 77 thru 85 FX models, and 86 thru 94 FXR models. 741839 Dash screw kit, fits 77 thru 85 FX models 741840 Dash screw kit, fits 86 thru 94 FXR models, except 88-up FXRS REPLACEMENT LENSES FOR FAT BOB DASHES Our replacement lenses can be used to restore original equipment or as replacement for Zodiac dashes. Lenses are sold each. 165124 Lens for 3-light dash red 165122 Lens for 3-light dash blue 013055 Lens for 2-light dash red, GEN- OIL -057

Speedo & Tacho Fits 47 thru 2003 models with either cable or electronic drive 744263 Display with blue digits 744264 Display with red digits Fits 2004-2010 Softail, 2004-2011 Dyna and 2004 to present Touring with electronic drive Has all the same features as mentioned above, but also has * ABS indicator * Cruise Control engaged indicator * Security Indicator for 2004 thru 2006 models * Fully compatible with stock SAE J1850 data bus 744265 Display with blue digits 744266 Display with red digits Optional accessories 236383 Transmission or wheel driven cable to Dakota Digital adapter 236385 Inductive pick up sender 731475 Oil pressure sensor 731478 Oil temperature sensor DAKOTA DIGITAL INFORMATION CENTER O.K., it is a speedo, but with so many functions that we prefer to call it an Information Center. These Information Centers are designed to fit all single gauge tank mount applications. 255 MPH/ km/h selectable speedometer Wrap around adjustable tachometer with adjustable shift point, can also display in digital numeric readout Odometer with two resettable trip odometers User settable countdown Miles to Service with warning and hour meter Clock (12 hour format) Voltage readout with low voltage alert Oil Pressure (requires installation of an optional pressure sender) Oil Temperature (requires installation of an optional temperature sender) 7 Speed Gear Position Indicator compatible with 3-7 speed transmissions Speed Calibration option for those who have changed rear pulley, front sprocket, stock transmission, or stock tires Various indicators can also be displayed such as Turn Signal, High Beam, Neutral, Low Oil Pressure, and Low Voltage Automatic turn signal canceling compatible "Wait to start" / Check Engine light Several performance calculations include: 0-60 time, high speed & high RPM recall, 1/4 mile time and speed Chrome front bezel with non-glare scratch resistant lens Machined aluminum housing also available in a fully compatible version for 2004 to present models, designed to work with the stock SAE J1850 data bus. Case diameter measures 4 1/4", bezel diameter of 4 5/8" -058

Speedo & Tacho DAKOTA INFORMATION CENTERS Dakota Information Centers are available in 4 versions Deluxe Classic, Deluxe Hooded, Deluxe Oval, and Deluxe Spiked.All versions feature: easy to calibrate speedometer in your choice of 0-9 KPH or 0-9 MPH quick response bar graph tachometer with 0-8.000 RPM odometer with trip odometer various indicators for turn signal, high beam, low oil pressure, neutral, wait to start and service engine machined aluminum housing with chrome front bezel and non-glare scratch resistant lens Auto-cancel turn signal compatible oil pressure gauge (sender included) fuel level gauge (use stock sender) voltmeter gear position readout clock countdown service meter performance display for 0-60 MPH-KPH timer, 1/4 mile time, maximum speed and RPM recall 236393 Deluxe Hooded 744261 DeLuxe Oval ODYSSEY FLAT OVAL DIGITAL TACHOMETER BY DAKOTA DIGITAL A quick response tachometer that works with both Single and Dual fire ignitions. Features high contrast teal display for easier daytime viewing and can be mounted directly on the handlebar in the above or below position, or with a flat or 35 degree triple-tree mount. RPM range from 0-8,000 RPM. Scale reading is accurate in increments of 100 RPM. Measures 4 1/8" long, 2" wide and 1 3/4" high. Mount must be separately ordered. 731485 Oval mini tachometer The information centers are compatible with both electronic and cable drive applications. Cables, cable drive pulse generator, inductive sensor, and adapter for OEM sensor are sold separately. Information Centers can be mounted either above or below bars. Mounting brackets are also to be ordered separately. 744262 DeLuxe Spiked Optional sensors 236383 Transmission or wheel driven cable to Dakota Digital adapter 236385 Inductive pick up sender 236384 Adapter for use with OEM sensor 744269 Dakota transmission sensor (works without adapter) Information Centers with selectable MPH and KM/H 744260 DeLuxe Classic -059

Speedo & Tacho ODYSSEY FLAT OVAL DIGITAL SPEEDOMETERS BY DAKOTA DIGITAL These digital instruments utilize Dakota's high contrast teal display for easier daytime viewing.they can be mounted directly on the handlebar in the above or below position, or with a flat or 35 degree triple-tree mount. Speedometer can be used in KM/H or MPH mode. Can be driven by the OEM electronic speed sensor when used in combination with the Dakota adapter, inductive sensor (for counting gear tooth) as well as a normal cable when used with the unique Dakota pulse generator. Speedo measures 4 1/8" (10.5 cm) long, 2" (5 cm) wide and 1 3/4" (4.5 cm) high. Meter housings and mounting hardware are high quality chrome plated. Meters, mounts and sensors must be separately ordered. 236387 Spiked digital speedometer 236383 Transmission or wheel driven cable to Dakota Digital adapter ODYSSEY ROUND DIGITAL MINI METERS BY DAKOTA DIGITAL For the Custom builder that wants more than the average, Dakota Digital developed a unique and very complete series of precision digital round instruments. These digital instruments are available as speedo, tacho, oil pressure, oil temperature, voltage and head temperature meter. Speedometers are available in 3 3/8" (86 mm) as well as in 2 1/16" (52 mm).tachometers are 3 3/8" (86 mm) diameter. Oil pressure, oil temperature, voltage and cylinder head temperature meters are 2 1/16" (52 mm) diameter and fit most aftermarket mounts. Sensors must be ordered separately. Digital Mini Speedometer Adjustable speedometer with odometer reading. This speedometer can be driven by the OEM electronic speed sensor when used in combination with the Dakota adapter, inductive sensor (for counting gear tooth) as well as a normal cable when used with the unique Dakota pulse generator. Available with 0-250 MPH or KM/H scale. Measures 4 1/8" (10.5 cm) long, 2" (5 cm) wide and 1 3/4" (4.5 cm) high. Three great looking styles to choose from. Meters, mounts and sensors must be separately ordered. 236388 Classic Oval digital speedometer 236385 Inductive pick up sender 236384 Adapter for use with OEM sensor 3 3/8" (86 mm) Mini Speedometer Adjustable speedometer with odometer reading. A unique alpha numeric read out is used to display odometer, trip odometer, service meter, high speed recall, and 0-60 time. This speedometer can be driven by the OEM electronic speed sensor when used in combination with the Dakota adapter, inductive sensor (for counting gear tooth) as well as a normal cable when used with the unique Dakota pulse generator. Has selectable KM/H or MPH readout. 731494 Mini digital speedometer with selectable KM/H or MPH readout 236383 Transmission or wheel driven cable to Dakota Digital adapter 236385 Inductive pick up sender 236384 Adapter for use with OEM sensor 236386 New Oval digital speedometer 744269 Dakota transmission sensor (works without adapter) -060

Speedo & Tacho 3 3/8" (86 mm) Digital Mini tachometer Displays RPM along with high RPM recall, shift point set, and hour meter. RPM range from 0-9,990 RPM. Scale reading is accurate in 10 RPM resolution. 731499 Digital Mini tachometer 236377 Mini digital Info Center 236383 Transmission or wheel driven cable to Dakota Digital adapter 236385 Inductive pick up sender 236384 Adapter for use with OEM sensor 744269 Dakota transmission sensor (works without adapter) 2 1/16" (52 mm) Digital Mini Oil Temperature Meter Available in your choice of Fahrenheit or Celsius reading. Scale range from 0-400 F or 0-200 C in 1 increments. Must be used with the Dakota Digital oil temperature sensor. 731497 Digital Mini oil temperature meter, Celsius or Fahrenheit 731478 Oil temperature sensor 2 1/16" (52 mm) Mini Speedometers and Info Centers Adjustable speedometer or Info Center with odometer reading. These can be driven by the OEM electronic speed sensor when used in combination with the Dakota adapter, inductive sensor (for counting gear tooth) as well as a normal cable when used with the unique Dakota pulse generator. Speedometers are available with 0-250 MPH scale or KM/H scale. The Info Center is 0-9 MPH or KM/H selectable and features a bar-graph tachometer and warning light functions. Note that the speedometers and Info Center do not use the sames sensors. 731449 Mini digital speedometer KM/H 731448 Mini digital speedometer MPH 731468 Cable driven pulse generator 731469 Inductive sensor 731470 Adaptor for use with OEM sensor 744269 Dakota transmission sensor (works without adapter) 2 1/16" (52 mm) Digital Mini Voltmeter Reads the system voltage. Scale range from 8 to 17 Volts with a 0.1 Volt resolution. 731500 Digital Mini Voltmeter 2 1/16" (52 mm) Digital Mini Oil Pressure Gauge Scale range from 0 to 150 PSI with a 1 PSI resolution. Must be used in combination with the Dakota Digital pressure sensor. 731501 Digital Mini Oil Pressure Gauge 731475 Oil pressure sensor 2 1/16" (52 mm) Digital Mini Cylinder Head Temperature Meter Selectable scale ranging from 150-750 Fahrenheit in 4 increments or 65-400 Celsius in 3 increments. 731496 Digital Mini cylinder head temperature meter 731589 Temperature sensor -061

Speedo & Tacho ODYSSEY DASH MOUNT DIGITAL MINI METERS BY DAKOTA DIGITAL For the Custom builder that wants to install more than the average meter in a dash or fairing, Dakota Digital developed a unique and very complete series of precision Custom dash mount digital instruments.these digital instruments are available as tacho, oil pressure, oil temperature, voltage and head temperature meter. Sensors must be separately ordered. Bar-graph Mini tachometer Displays RPM in the range from 0-8,000 RPM in 100 RPM increments. 731471 Bar-graph Mini tachometer Digital Mini tachometer Displays RPM in the range from 0-9,990 RPM in 10 RPM increments. 731472 Digital mini tachometer Digital Mini Oil Temperature Meter Available in your choice of Fahrenheit or Celsius reading. Scale range from 0-400 F or 0-200 C in 1s increments. Must be used with the Dakota Digital oil temperature sensor. 731476 Digital mini oil temperature meter, Fahrenheit 731478 Oil temperature sensor Digital Mini Voltmeter Reads the system voltage. Scale range from 8 to 17 volts with a 0.1 Volt resolution. 731473 Digital mini Voltmeter DAKOTA DIGITAL GEAR INDICATOR Dakota Digital's PGR-1000 series gear indicators are self-programming. Simply hook them up and ride through all of the gears and you are done.they can be used on any 12 Volt motorcycle with an electronic speed signal, also known as speed sensor. Features 1-7 gear readout, neutral indicator, selfdimming, chromed machined 1 1/4" (32 mm) diameter aluminum housing and built-in mounting bracket.available with 1", 1 1/4" and 1 1/2" handlebar mount or flush mount for use in fairings and other panel mount applications. 236389 For 1" (25.4 mm) handlebars 236390 For 1 1/4" (32 mm) handlebars 236391 For 1 1/2" (38 mm) handlebars 236392 Flush mount Dimensions in millimeters ZPN 731471 Bar-graph mini tachometer A = 86 mm, all others A = 68 mm. All other dimensions are the same for all meters; B = 47 mm, C = 6 mm, D = 40 mm, E = 40 mm, F = 79 mm. Digital Mini Oil Pressure Gauge Scale range from 0 to 150 PSI with a 1 PSI resolution. Must be used in combination with the Dakota Digital pressure sensor. 731474 Digital mini Oil Pressure Gauge 731475 Oil pressure sensor -062

Speedo & Tacho PRO-MAX DIGITAL SPEEDO & TACHOMETER For the custom builder that wants more than just the average, Pro-Max designed and developed this unique and very complete speedometer & tachometer combination.this digital instrument has a built-in bar-graph tacho, digital odometer, trip meter and display indicators for High Beam light, Neutral gear indicator, Oil pressure and Turn signals.works on stock transmission mounted electronic speed sensor as used on 94 and later models. Alternatively, electronic pulse generators that connect to a stock wheel or transmission driven speedo cable are available separately. The Pro-Max digital speedo features program mode to adjust to your transmission, final drive ratio and rear wheel size.all of this is in a beautiful chromed billet aluminum housing, measuring 4 11/32" (110 mm) long, 2 7/32" (57 mm) high and 1 1/64" (38 mm) wide.the handle bar mounts are available in 1" (25.4 mm), 1 1/4" (31.75 mm) and 1 1/2" (38.1 mm) diameter in Smooth or Tri-Groove finish and must be ordered separately. Note: Speedo sending unit and mounting bracket are not included Digital Tacho & Speedometer 169375 MPH 169383 KM/H Cable driven pulse generators 160798 For cables with 5/8" top nut 160799 For cables with 12 mm top nut Smooth finish handle bar mounts 169376 For 1" (25.4 mm) handle bar 169377 For 1 1/4" (31.75 mm) handle bar 169378 For 1 1/2" (38.1 mm) handle bar Tri-groove finish handle bar mounts 169379 For 1" (25.4 mm) handle bar 169380 For 1 1/4" (31.75 mm) handle bar 169381 For 1 1/2" (38.1 mm) handle bar MPH/KPH SPEEDOMETER FOR 96 THRU 98 SOFTAILS This original equipment electronic speedometer features a scale that gives you your speed in both miles and kilometers per hour. Can be used on all models with the transmission mount electronic speed sensor. 237914 Electronic MPH/KPH speedometer MPH SPEEDOMETER FOR 96 THRU 98 SOFTAILS This original equipment electronic speedometer can be used on all models with the transmission mount electronic speed sensor. 237922 Electronic MPH speedometer SPEEDOMETER MOUNTING KIT Fits all models with cast dashes from 68 to present. Kit includes a rubber gasket (OEM 67067-76), two mounting pins (OEM 67066-76), two pin clips (OEM 67069-76), and two grommets (OEM 67070-76). 169064 Speedo to dash mount kit STOCK STYLE ELECTRONIC SPEEDO FOR 96 THRU 98 SOFTAIL Electronic controlled black faced KM/H speedo with digital odometer for use on 96 thru 98 Softail models that are equipped with the transmission fitted electronic speed sensor pick up. Meter is 4 1/2" (11.5 cm) in diameter and fits stock dash and stock 12-pin wiring harness plug. 169081 Electronic KM/H speedo (OEM 677-99A) CABLE DRIVEN ELECTRONIC SPEEDO FOR 47 TO PRESENT DASH Cable driven electronic controlled black faced speedo with digital odometer and 2 trip meters. Comes pre-wired with a push button switch to select trip 1, trip 2 or odometer and is programmable for use with any ratio speedo drive. Installation instructions and an adapter nut for use with either 5/8" or 16 mm speedo cable nut. Meter is 4 1/4" (108 mm) in diameter and a 4 3/4" (120 mm) top ring. Fits most Fat Bob style dashes 57 thru 95.Available with 120 MPH or 220 KM/H scales. 169353 KM/H scale 169352 MPH scale -063

Speedo & Tacho CABLE DRIVEN ELECTRONIC SPEEDO/TACHO FOR 47 THRU 95 Cable driven electronic controlled black faced speedo with digital odometer, 2 trip meters and tacho. Comes pre-wired with a push button switch to select trip 1, trip 2 or odometer and is programmable for use with any ratio speedo drive. Installation instructions and an adapter nut for use with either 5/8" or 16 mm speedo cable nut. The tacho works with both Dual and Single Fire ignitions. Speedo/tacho meter combo is 4 1/4" (108 mm) in diameter and a 4 3/4" (120 mm) top ring. Fits most Fat Bob style dashes 47 thru 95.Available with 120 MPH or 220 KM/H scales, tacho goes up to 8,000 RPM. 169351 Speedo/Tacho combo with KM/H scale 169350 Speedo/Tacho combo with MPH scale SPEEDOMETERS Zodiac offers a complete line of precision built speedometers. All speedometers feature resetable trip mileage indicator, speedo to dash gasket and quality glass lens. These within OEM calibration quality built instruments are offered in 1:1 and 2:1 ratio with kilometers per hour or miles per hour scale.the 2:1 ratio works with all FL models 47 thru 67 as well as FL models 81-84 with front wheel driven speedometers and FX, FXR and Sportster models with front wheel drive speedo unit. The 1:1 ratio works with FL-FX-FXWG models 68 to present with transmission drive speedo unit. WHITE FACE 36-40 STYLE 169084 2:1 ratio MPH 5/8" nut 169026 1:1 ratio MPH 5/8" nut 169092 2:1 ratio KM/H 5/8" nut BLACK FACE 68 THRU 84 STYLE 169091 2:1 ratio KM/H 5/8" nut 169010 1:1 ratio KM/H 5/8" nut 169094 2:1 ratio KM/H 16 mm nut POLICE SPECIAL SPEEDOMETERS These large diameter speedo's fit the stock FL style dash as well as our Cat-Eye dash and two and three light dash. Police Special speedo's are available with 1:1, 2:1 and 2.21:1 ratio. Speedo's come complete with light socket, bulb and gasket. 1:1 Ratio, fits all transmission driven FL, FX, FXWG models 68 thru 84. Has 5/8" cable connector thread. 1697 Police Special speedo MPH RUBBER SPEEDOMETER DAMPENER This simply to install die-cut rubber dampener fits FL style speedometers when used with cast dash on many Big Twin models from 68 to present. It helps absorb harmful vibration, making units easier to read and last longer (OEM 67115-91)(sold each). 1692 Rubber Speedo dampener BLACK FACE 46 THRU 47 STYLE 169086 2:1 ratio MPH 5/8" nut 169093 2:1 ratio KM/H 5/8" nut 169025 1:1 ratio MPH 5/8" nut 169027 2:1 ratio KM/H 16 mm nut 2:1 Ratio, fits all transmission driven FL models 47 thru 67 as well as 80 thru 84 models with front wheel drive and Sportster, FX and FXR models 73 thru 90 with front wheel drive units. Has 5/8" cable connector thread. 1698 Police Special speedo MPH 2.21:1 Ratio, fits front wheel drive FXWG 84 thru 85 and FXST/FLST 84 thru 90. Has 12 mm cable connector thread. 1691 Police Special speedo MPH -064

Speedo & Tacho SPEEDO/TACHO FOR FAT BOB DASHES A totally improved speedo and tacho meter combination which fits all large Fat Bob dashes from 47 to present.the precisionbuilt speedometer is combined with a solid state 6000 RPM electronic tacho meter that accurately tracks engine speed by reading the coil output.the 1:1 ratio speedo meter works with FL-FX-FXWG models 68 up with transmission drive speedo unit.the 2:1 ratio speedometer is used for transmission drive units on 47 thru 67 models, as well as late model front wheel drive applications. When installed in conjunction with front wheel drive units, one of our Custom speedo cables must be used (ZPN 114152, 114246). Available in Miles per Hour as well as Kilometers per Hour. SPEEDOMETERS FOR FXWG-FXST- FLST MODELS Special 2.21:1 ratio front wheel drive speedometers to fit 84 thru 86 FXWG, 84 thru 90 FXST, FLST models.will also fit 91 and later FXST and FLST models, but these speedos don't have the electronic reed switch for self-canceling turn signals. They feature 12 mm thread and come with a gasket. Late-style trip reset knob and screw must be used on 84 thru 89 models. 90 and later models use stock knob. Available in three face styles. SPEEDOMETER FOR FXWG-FXST- FLST MODELS These front wheel drive speedo's have a special ratio (2.21:1) to fit FXWG 84-85 and FXST/FLST 84 thru 90. They have 12 mm connector thread and come complete with gasket.takes late (90 up) style OEM or Zodiac trip reset knob and screw. 1690 Speedo 169200 62 thru 67 face 169165 Speedo/Tacho combo 2:1 MPH 169188 Speedo/Tacho combo 1:1 KM/H 169189 Speedo/Tacho combo 2:1 KM/H 169201 46 thru 47 face SPEEDOMETER FOR 83 THRU 90 FX/FXR AND SPORTSTER Stock replacement speedo-meter for the steel cased speedo on FX/FXR and Sportster models from 83 thru 90 (OEM 67020-85A). 169037 Speedometer 169202 36 thru 40 face -065

Speedo & Tacho TACHOMETER FOR FX MODELS Stock replacement tacho-meter for FX models 73 thru 82 with handlebar mounted instruments and 77 thru 84 FXS models with tank mounted instruments (except FXWG & FXST).Waterproof construction and vibration resistant (OEM 92042-78A). 169012 Tachometer HANDLEBAR MOUNTED TACHOMETER This 6200 RPM tachometer is a direct replacement for the Original Equipment part fitted to Sportster models from 85 thru 93. However, it can be used on Big Twin models from 83-99 (OEM 67111-85). 169041 Tachometer CHROME SPEEDO AND TACHO COVER SET Full-coverage chrome speedometer and tachometer cover set. Easily slips over the stock instrument housing, makes use of the existing hardware without any modification. Is a perfect match with our chrome instrument mounting brackets ZPN 169152 & 169158. 169154 Speedo tacho cover set, fits FX(R) & Sportster 84 thru 90 with handlebar mounted speedo/tacho (OEM 67092-85/67112-83 and 67090-85/67105-83) 169155 Speedo cover only, fits single instrument FX(R) & Sportster 84 thru 90 FX SPEEDOMETER Speedometer that fit all 73 thru 82 FX models with handlebar-mounted instruments, and 77 thru 84 FX models, (except FXWG, FXST) with tank-mounted instruments. This speedometer has a 120 MPH face to make it easier to read at a glance, and comes complete with light socket, dash gasket and a mounting bracket (OEM 67020-73B). 169180 Speedometer METERS FOR SPORTSTER AND FXR MODELS Stock replacement tachometer with 8000 RPM scale for 74 thru 83 Sportster and 82 thru 83 FXR models. Great for custom applications. 169009 Tachometer SPEEDO/TACHO METER MOUNTING GASKETS These foam rubber mounting gaskets are direct replacements for the original equipment's parts. They fit the metal-cased instruments used on Sportster, FX and FXR models from 83 to present and are available with or without a visor. 1693 With visor (OEM 67039-83) 1694 Without visor (OEM 67104-83) -066

Speedo & Tacho BILLET ALUMINUM GAUGE BEZELS Manufactured from 6061-T6 aluminum, these covers are a real upgrade for your bike. The bezels have a black anodized finish with silver dimples. Also available in a smooth chromed finish, with or without dimples. Fits 2" volt meter, oil pressure, fuel and air temperature gauges as found on 86 to present FLT and FLTR models as well as on 2000 to present FLHT and FLHX models.also fits many meters with 46 mm internal and 55 mm external diameter top rings. The 3 5/8" bezels fit 84 thru 99 Touring models and 2000 to present FLHT, FLTR and FLHX models. Also fits many meters with 84 mm internal and 93 mm external diameter top rings. Bezels are supplied in sets of 2. Easy to install with clear silicone (not included). Fits 2" volt meter, oil pressure, fuel and air temperature gauges as found on 86 to present FLT and FLTR models as well as 2000 to present FLHT and FLHX models A. 169506 Pair chrome smooth billet bezels B. 169507 Pair chrome dimpled billet bezels C. 169508 Pair chrome billet bezels with black dimples D. 169509 Pair black billet bezels with silver dimples Fits 3 5/8" gauges on 84 thru 99 Touring models and 2000 to present FLHT, FLTR and FLHX models E. 169501 Pair chrome smooth billet bezels F. 169502 Pair chrome dimpled billet bezels G. 169503 Pair chrome billet bezels with black dimples H. 169504 Pair black billet bezels with silver dimples PRO CYCLE 2 5/8" TACHOMETERS Auto Meter offer a brilliant chrome 2 5/8" tachometer for Custom street and show motorcycles. These water resistant tachs are built with the same technology as Pro-Cycle's racing products, have a 8000 RPM scale and work with all stock and popular aftermarket 1 and 2 pulse ignitions (single and dual fire). Available with black or white dial and many choices of bezel and cup. 710600 Black dial with chrome bezel and cup 710601 White dial with chrome bezel and cup 710602 Black dial with aluminum bezel and black cup 710605 White dial with black bezel and cup PRO CYCLE CHROME 3 3/4" TACHOMETERS Precision 8,000 RPM tachometers with chrome plated housings from Auto Meter, the very same company that makes most reliable tachometer for race bikes and cars. Race technology, quality and beauty in one. Pro Cycle tachometers are water resistant and have 3 3/4 inch diameter (95 mm).they work with all stock and popular aftermarket single and dual fire ignitions.a mounting bracket is separately available. The Pro Meter tach is available with a white, black or silver colored face. 239563 Tachometer with black face 239564 Tachometer with white face 239565 Tachometer with silver face 239571 Mounting bracket 239574 Shock strap kit for mounting bracket PRO CYCLE 5" RACING TACHOMETER WITH SHIFT LITE BY AUTO METER Auto meter claims the 5" Pro Cycle tachometer is the most accurate unit available. The scales runs to a maximum of 10.000 RPM and the unit has a built-in shift warning light to prevent you from over-reving your engine. A must for every serious Harley racer. The 5" diameter precision gauge ensures optimal view on your accurate rpm, while the clear, amber warning light tells you when to shift for maximum performance.the shift lite can be set easily by a selector on the gauge. Comes complete with mounting bracket. For those that run Single Fire ignition a tach adapter for two coils is included. Brackets for handlebar mount as well as the shock strap and tach adapter are separately available. 239562 Complete set 239571 Mounting bracket 239574 Shock strap kit for mounting bracket 232281 Tacho meter adaptor PETITE VOLTAGE METER 48/SPECCHAR("HARDSPACE"MM A great match with our mini speedo's and tacho's, is only 48 mm in diameter, 47 mm long and has a top ring of 52 mm. Housing is made out of high luster polished stainless steel. Meter comes pre-wired for ease of installation. 169239 Mini Voltage meter -067

Speedo & Tacho MMB'S 48 MM MINI SPEEDO'S, TACHO'S AND GAUGES Many bike builders put in a lot of effort to give their bike a unique and personal appearance. Many times they are limited in their choice of speedo's, tacho's and other handlebar instruments. Today, however, MMB provides them a variety of mini gauges in various colors. The conservative builder can continue with his preference of black and white gauges, while those who want more can choose from, yellow, red, or blue.these mini gauges have a diameter as little as 48 mm with a top ring of 52 mm.the housing has a length of 47 mm.available are cable driven and electronic driven speedometers in Kilometers per hour as well as Miles per hour, clocks, volt meters and a mini control panel with 4 control lights. Faces are available in black, white, red, yellow and blue. These meters feature all chrome housing and dial illumination. All meters, except the elctronic speedo's, come complete with chrome mounting bracket. A. Mini Speedo 1:1 ratio Fits transmission driven FL 68 thru 80, FXWG 80 thru 84, FX 71 thru 72 Black White Red Yellow Blue 710200 710204 710208 710212 710216 KM/H 710201 710205 710209 710213 710217 MPH 2:1 ratio Fits FL 47 thru 67 & 81 thru 84, FX(R) 73 thru 94 and Sportster 54 thru 95 Black White Red Yellow Blue 710202 710206 710210 710214 710218 KM/H 710203 710207 710211 710215 7102 MPH B. Mini Volt meters Black White Red Yellow Blue 710225 710226 710227 710228 710229 C. Mini Digital Clock Features an internal battery to indicate the correct time Black White 710237 710238 D. Mini instrument panel with control light for indicator, neutral, high beam and oil pressure Black White Yellow Red Blue 710233 710234 710235 7108 7109 E. Electronic Speedo Can be used with OEM transmission mounted or the separately available speed sensor that can be fitted on wheel, hub disc brake rotor or rear sprocket.. Features LCD display for the read out of time, total distance, trip distance and analogue read of your speed.all you got to do is to install two mini switches (like our ZPN 741160) to switch between the different read outs. Black White 710370 710371 KM/H 710372 710373 MPH 710239 Optional speed sensor A. Cable driven Mini Speedo B. Mini Volt meters C. Mini Digital Clock D. Mini instrument panel E. Electronic driven Mini Speedo Replacement parts 710236 Bulb for dial illumination with socket and wire -068

Speedo & Tacho PRO CYCLE RACING TACHO METERS BY AUTO METER Auto Meter has set the newest standard in tacho meters for Harley riders that need instant, accurate information about motor RPM. These instruments feature the same reliability and technological quality as Auto Meter.s race proven automotive tachometers. They are water resistant and come with a mounting bracket. They work with all stock and popular aftermarket single and dual fire ignitions. These tachometers offer accurate and visible readings and good looks, which makes them perfect for the serious racer, as well as for the show bike enthusiast. The 8,000 RPM tachometer is 3 3/4" in diameter, and the 10,000 RPM tachometer is 5" in diameter. 239560 3 3/4" Tachometer with bracket 8,000 RPM 239561 5" Tachometer with bracket 10,000 RPM 239571 Mounting bracket 239574 Shock strap kit for mounting bracket PETITE 48 MM MINI SPEEDO'S AND TACHO'S "Petite" speedo's and tacho's are 48 mm diameter with a top ring of 52 mm, and are only 47 mm long. Available are 1:1 ratio speedometers in Kilometers per hour and electronic tachometers for use with dual fire ignition. Tachometers can also be used with Single Fire ignition when used in combination with our ZPN 232281 tacho meter adaptor. 160420 Mini Speedo, 1:1 ratio fits transmission driven FL 68 thru 80, FXWG 80 thru 84, FX 71 thru 72, black face 160428 Electronic Mini Tacho for Dual fire ignition, 12.000 RPM scale, black face MINI INSTRUMENTS Speedo's and tacho's in 60 mm diameter 2:1, fits FL 47-67 & 81-84, FX/FXR 73 to present, and Sportster 54 to present. 169065 KM/H scale 169020 MPH scale 1:1, fits transmission driven FL 68-80, FXWG 80-83, FX 71-72, and Triumph T120/150 67 up. 169068 KM/H scale 169022 MPH scale 2.1:1, fits all Kawasaki, Honda, Suzuki, Yamaha and most front wheel driven European makes and models. 169021 KM/H scale 169023 MPH scale Mini Tachometers 169031 2:1, fits all Harley except models with electronic tacho, Norton all models except Commando 169030 4:1, fits Honda 550/750/ 1000/1100, all models Suzuki & Yamaha,Triumph TR6/T120/T120, Norton Commando, some BSA Replacement bulbs 167393 Replacement bulb (10 pack) Note: Mini speedo's and tacho's will NOT replace electronic gauges. -069

Speedo & Tacho/Speedo Mount MMB'S DIGITAL LCD SPEEDO A 2-line red or blue lighted LCD digital speedo with button switch to switch between 7 available functions. Such as speed in MPH or KM/H, total distance, 2 different trip distances, and on-board voltage. When connected to a temperature sensor it can also indicate engine- or oil temperature. These meters are available with a black or white face, chrome or black housing, and red or blue dial illumination. Housings are 48 mm in diameter and have the switch button installed in the lower cap. Meters can also be fitted in our 48 mm diameter meter caps and brackets when you re-locate the switch button.available as complete kits with black or chrome cap and bracket, as well as individually. Complete kits 744181 Chrome cap, black face, red illumination 744182 Chrome cap, black face, blue illumination 744183 Chrome cap, white face, red illumination 744184 Chrome cap, white face, blue illumination 744185 Black cap, black face, red illumination 744186 Black cap, black face, blue illumination 744188 Black cap, white face, blue illumination Individual parts 710397 Chrome bracket and cap 710369 Black bracket and cap 710309 Micro push button switch Individual speedo's with chrome housing and chrome bezel 710389 White face, red illumination 710391 White face, blue illumination 710390 Black face, red illumination 710392 Black face, blue illumination Individual speedo's with black housing and black bezel 710393 White face, red illumination 710395 White face, blue illumination 710394 Black face, red illumination 710396 Black face, blue illumination ROCKER BOX MOUNTED DIGITAL LCD LED SPEEDO Digital instruments and LED technology are a welcomed part for each custom bike in the 21st century. The LCD speedometer shows speed, total distance and trip distance in large digits and also features bright blue LED illumination. Speedometer is easy programmable with a 2-switch mechanism. Comes complete with a billet aluminum bracket that mounts to the rear rocker box, and features 3 holes for the OEM control lights.also included is a special speed sensor, but can also be used with OEM transmission mounted speed sensors when used in conjunction with our ZPN 744298 speed sensor adapter.these LCD/LED speedometers are in KM/H and available with a chrome plated, black, or polished aluminum bracket to fit on the left side of your engine for 84 thru 99 Evolution Big-Twin models, and 99 to present Twin-Cam models. Fits 84-99 Evolution Big-Twin models 722660 Polished 722661 Chrome 722664 Black Fits 2000 to present Twin-Cam models 722662 Polished 722663 Chrome 722637 Black Optional Parts 744298 Digital speedo transmission adapter -070

Speedo Mount RBS DIGITAL MINI INSTRUMENTS RBS digital mini speedo's and tacho's are available with a variety of billet aluminum mounting brackets. The digital gauge is 2 13/32" (61 mm) in diameter and 2 3/32" (57 mm) long.these meters feature a LCD display with blue LED back illumination. The speedometer shows your choice of speed, odo or trip meter, the tachometer shows RPM or ambient temperature. You can select between these options by use of the 2-switch mechanism on the back of the instrument. Speedo-sensor required installation materials and instruction manual are included. Can also be used with an OEM transmission mount speed sensor if installed with the separately available adapter ZPN 744298. RBS Single Straight Handlebar Instruments Single speedo or tacho to be mounted on all 73 to present models with 3 1/2" (89 mm) center-to-center risers with offset mounting holes. Straight bracket is 5 1/2" (140 mm) long,5 1/8" (130 mm) wide and 3 /32"(91 mm) deep. Pre-bored to adapt indicator lights, which are available separately. Speedo Tacho 733603 722960 Polished 733604 722961 Chrome 733605 722962 Black RBS Single Pullback Handlebar Instruments Single speedo or tacho with a 40 degree angled bracket that fits on all 73 to present models with 3 1/2" (89 mm) center-to-center risers with offset mounting holes. Bracket is 6 7/32" (158 mm) long and 5 1/8" (130 mm) wide. Pre-bored to adapt stock style indicator lights. Speedo Tacho 733606 722963 Polished 733607 722964 Chrome 733608 722965 Black RBS Universal Speedo's and Tacho's Easy to mount digital speedo or tacho with universal bracket. Because of the single mounting point and 360 degree rotatable instrument these can be mounted in any position.the meter bracket is 4 11/16" (1 mm) long, 2 7/8 (73 mm) wide, total height is 3 /32" (91 mm). Available in polished, chrome or black anodized.speedo Speedo Tacho 733600 722638 Polished 733601 722639 Chrome 733602 722796 Black RBS Straight Handlebar Speedo/Tacho combo Speedo and tacho integrated in a billet aluminum bracket that bolts straight on 73 to present models with 3 1/2" (89 mm) center-to-center risers with offset mounting holes. The bracket is 5 1/2" (140 mm) long, 5 11/16" (144 mm) wide and 3 /32" (91 mm) deep. Features indicator light bores. 733609 Polished 733610 Chrome 733611 Black RBS Angled Dual Pullback Handlebar Speedo/Tacho combo Speedo and tacho integrated in a billet aluminum 40 degree angled bracket that bolts straight on to all 73 to present models with 3 1/2" (89 mm) center-to-center risers with offset mounting holes.. Bracket is 6 7/32" (158 mm) long and 5 11/16" (144 mm) wide. Indicator lights not included. 733612 Polished 733613 Chrome 733614 Black -071

Speedo & Tacho 80 MM ELECTRONIC SPEEDO'S These 3.149" (80 mm) diameter electronic gauges feature a stainless steel housing and mounting bracket.they come pre-wired and complete with a handlebar mounting clamp and push button to switch between the digital total and trip odometer readout. Speedo's work with the stock 95 to present transmission mounted speed sensor or with our cable driven speed sensor adapter ZPN 160798 for cables with 5/8" top nut or ZPN 160799 for cables with a 12 mm top nut. 169384 With MPH scale 169385 With KM/H scale Cable driven pulse generators 160798 For cables with 5/8" top nut 160799 For cables with 12 mm top nut CHAMELEON 2 3/8" MINI SPEEDOMETERS A simple press of a button allows you to change the color of lighting in the face of these speedometers. You can switch from Red, to Amber, to Blue, to Yellow, to Green, to White, to Purple and back to Red again. These speedo's feature a 2 3/8" (61 mm) diameter, 2 3/4" (70 mm) long stainless steel housing with a high luster polished finish, and a 2 5/8" (67 mm) chrome bezel ring. Available in 1:1 and 2:1 ratio with MPH or KM/H scale. 1:1 ratio Fits transmission driven FL 68 thru 89, FXWG 80 thru 84, and FX 71 thru 72. 169260 MPH scale 169261 KMH scale MINI ELECTRONIC SPEEDO These electronic speedo's can be used with OEM style transmission mounted speed sensors as used on 95 to present models. Speedo's feature a 2 3/8" (61 mm) diameter, 2 3/4" (70 mm) long polished stainless steel housing, and a 2 5/8" (67 mm) chrome bezel ring. Come complete with a universal mounting bracket, a rubber inserted handlebar clamp, LED light, digital odometer, digital trip meter and a push button switch to switch from odometer to trip meter or resetting the trip meter. Available with up-to 240 km/h black lettered white face or white lettered black face. 169271 White face 169272 Black face REPLACEMENT MW DIGITAL SPEEDO Replacement digital speedo as used in all MW billet aluminum Digital Speedo brackets. Can also be used for custom applications, using the included electronic wheel sensor that can be programmed for use with any wheel size. Easy to read multi-lingual instructions for the programming are also included. This digital speedo can also be used with a ZPN 741469 adapter kit to connect it to an OEM gearbox speed sensor. 7251 Replacement digital speedo Note: These late gray units do not fit early MW Digital Speedo brackets that were supplied with a black digital speedo. 2:1 ratio Fits FL 47 thru 67 & 81 thru 84, FX(R) 73 thru 94, and XL 54 thru 94 169262 MPH scale 169263 KMH scale MINI SPEEDO/ TACHO MOUNTING CLAMP Mini speedo / tacho mounting clamp complete with rubber bushing. Also usable for Custom applications. A perfect antivibration mount bracket. 169179 Mounting clamp MINI SPEEDOMETER WITH TRIP METER An improved version of our mini speedometer with the addition of a trip meter to keep track of your mileage since your last gas stop. Meters have a 2 3/8" diameter with 2 5/8" rim and are 2 1/8" high. Scales are available in Miles per hour as well as Kilometer per hour. Both have a 2:1 ratio and fits FL models from 47 thru 67 with transmission driven speedometers, FL models from 81 thru 84 with front wheel drive speedo drives,all FX and FXR models with front wheel driven speedo's and all Sportster and K models from 54 thru 95. These mini speedometers come with an anti-vibration handlebar mounting clamp. 169003 MPH scale 169004 KPH scale 167393 Replacement bulb (10 pack) -072

Speedo Calibration ELECTRONIC SPEEDOMETER CALIBRATOR This S&S Electronic Speedometer Calibrator allows the rider to correct the electronic driven speedometer as found on most Big Twin and Sportster models from 96 to present. The unit is very easy to install by unplugging the connector between the transmission sensor and speedometer and plugging these two connectors into the S&S unit.the calibrator can be used to correct the difference between actual and indicated speeds and mileage in 1% increments between -29% and +69%, a must when you have fitted a different-than-stock rear tire size, transmission sprockets, 6 Speed transmission, or belt drive pulleys. Unit is only 2 1/4" x 1 1/2" x 1 1/8" to permit a neat installation and is completely sealed for protection from weather and vibration. 236690 S&S Electronic Speedometer Calibrator SPEEDOMETER/TACHOMETER INTERFACE A.K.A. DATABUS BREAK OUT BOX This Speedometer/Tachometer Interface Adapter is also known as the Databus Break- Out Box. It allows you to interface most aftermarket Speedometers and/ or tachometers with the SAE J-1850 Databus signal created from the stock Harley- Davidson ECU on 2004 to present models. This device connects to the bike's databus and outputs traditional analog signals for a gauge of your choice. Outputs provided for accessory power and ground, adjustable tachometer signal for 1, 2 or 4 cylinder outputs (which includes V-Twin Single Fire and Dual Fire applications), speedometer signal (8,000ppm only) in addition to the Check Engine signal, normally only available on the data bus. The Break-Out Box also contains a digital readout which allows for both reading back and clearing diagnostic trouble codes,similar to a scan tool.kit comes complete with required harnesses and hardware. Note: Does not work on 2011 and later Softail and 2012 and later Dyna as these have a so-called CAN-Bus system. 744267 Databus Break-Out Box DAKOTA ADJUSTMENT UNIT FOR ELECTRONIC SPEEDOMETERS Dakota's electronic speedometer adjustment unit plugs directly into the stock sockets of 96 to present models with the electronic driven speedometer. This unit allows you to correct the speedometer and odometer reading after a change in tire or pulley size or when a different transmission (different ratio or 6 Speed) has been fitted. No cutting or splicing of the stock wiring harness is required, just plug it in the 3-pin connector plug between the transmission sensor and the speedometer. Two sealed push-button switches allow the speedometer reading to be increased or decreased easily while the bike is being driven. After you have set the speedometer to the correct reading, the unit stores the correction factor, even with the battery disconnected. The module is completely sealed from water, dust, and dirt. The correction range is from 50% to 200% of the original reading. Small steps allow precise correction to within 1 MPH or 1 KPH. 236986 Electronic Speedometer adjustment unit -073

Speedo Mount DIGITAL INSTRUMENT PANEL This is the latest in digital instrument panels. This Hi-Tech box is only 2" wide and 3.35" long and provide you with all the info you need. It provides speedometer and tachometer functions and all the required indicator lights in the correct colors such as oil, neutral, right turn- and left turn signal and high beam. This instrument utilizes daylight readable L.E.D.'s for viewing in direct sunlight and a daylight sensor for auto dimming at night. NESS-TECH TORPEDO BULLET MOUNTS FOR DAKOTA DIGITAL 2 1/16 GAUGES Torpedo cover mounts directly to any 1" handlebar by drilling and tapping a 1/4"-28" hole Accepts any 2 1/16" Dakota Digital Gauges Carved from 6061-T6 billet aluminum Beautifully chrome plated Top Mount A06050 1" handlebar applications MOUNTS FOR DAKOTA DIGITAL FLAT OVAL METERS Mounts for flat oval speedometer, tachometer, and information center Handlebar mounts work in both the over as well as the under handlebar position. A. 731489 For 1" handlebars B. 731490 For 1 1/4" handlebars C. 731491 For 1 1/2" handlebars D. 731492 Flat triple tree mount E. 731493 35 triple tree mount Note: Digital output from transmission sensor and from ignition module is required, device will not work straight off the coil. 7313 Digital speedo/tacho for bar mount 7314 Digital speedo/tacho for panel mount 7315 Clamp for 1" bars 7316 Clamp for 1 1/4" bars 7317 Clamp for 1 1/2" bars BILLET ALUMINUM HANDLEBAR METER BRACKETS These billet aluminum brackets are designed to mount MMB meters on 1" handlebars, but can also be used for custom applications. Come complete with metric hardware. Available in chrome or black. Sold each. Fits 1" handlebars 710337 Chrome 710338 Black -074 MW CUSTOM HANDLEBAR CLAMP This MW Custom handlebar clamp is CNC machined from billet aluminum and has a high-gloss polished finish. Is pre-bored to accept stock control lights. Fits most 73 to present Harley models with 3 1/2" (89 mm) center-to-center risers with offset mounting holes. 710428 Billet aluminum with control light holes

Speedo Mount TRANSMISSION MOUNT ADAPTER FOR DIGITAL SPEEDO'S This is a very easy to mount adapter for use on all 96 to present Big Twin, Sportster,V- Rod and Buell models with the transmission mount electronic speedo pick up. It has been especially developed for use with MW digital speedometers. 741469 Digital speedo transmission adapter MW "DIGITAL SPEEDO" CUSTOM HANDLEBAR CLAMP These CNC machined aluminum Custom handlebar clamps feature a very small lighted digital speedo that can be switched from KPH into MPH and also gives trip and time.all kits come with an electronic wheel sensor and can be programmed for use with any wheel size by following the easy to read multilingual instructions. Can also be connected to the stock transmission mount electronic speed sensors when ZPN 741469 adapter kit is used. Handlebar clamps fit most 73 to present Harley models with 3 1/2" (89 mm) center-to-center risers with offset mounting holes. 710423 With digital speedo and control light holes MW 'DIGITAL SPEEDO' CLAMP & MINI METER BRACKETS These unique design Custom handlebar clamps feature a very small lighted digital speedo that can be switched from KPH into MPH and also gives trip and time.this digital speedo can be attached to the gear box speed sensor when ZPN 741469 adapter kit is used, or to the included electronic wheel sensor and can be programmed for use with any wheel size by following the easy to read multilingual instructions. Clamps are CNC machined from billet aluminum and have a high-gloss polished finish.also available with a bracket to take our MMB mini meters such as tacho,volt meter or mini instrument panel. These "Digital Speedo" clamps look even greater when you also fit a pair of MW squared billet aluminum risers (ZPN 710399 & 721879). 710416 With digital speedo and meter bracket 710417 With digital speedo, meter MW BILLET ALUMINUM RISERS These squared MW risers are CNC machined from solid blocks of billet aluminum and have a beautiful polished finish. They slightly pull back and give a rise of 2 3/8" (60 mm). 710399 Squared billet aluminum 2 3/8" high risers MW PAN AM BILLET RISERS These Pan Am risers are made from billet aluminum and have a mirror shine polished finish.they are only 2 3/8" (60 mm) high and are a perfect match with MW's Digital Speedo clamps. Fits most stock and stock style triple trees with OEM handlebar dampers. 721879 MW Pan AM aluminum risers 710422 With digital speedo 710414 With digital speedo 710415 With digital speedo and control light holes -075

Speedo Mount CHOPS 76 ROCKER BOX MOUNTED SPEEDO BRACKETS These Speedo brackets are a perfect Italian design. Perfectly machined and perfectly finished they are the finishing touch of your bike. The brackets bolts straight on to the rocker boxes of 95 to present Evolution Sportster models and take the stock warning lights and stock 3 1/2" (89 mm) diameter speedometer. Available in polished or black anodized billet aluminum. 743432 Polished 743433 Black anodized NESS CUSTOM SPEEDO BRACKETS These speedometer brackets are designed to mount 2 5/8" (67 mm) or 3 11/32" (85 mm) speedometers or tachometers to any 1" or 1 1/4" diameter T-bars 3 11/32" gauges are stock on selected 84 thru 94 Sportster and Dyna models Billet aluminum A06090 Chrome, single 3 11/32" gauge for 1 1/4" T-bars A06030 Chrome, single 2 5/8" gauge for 1 1/4" T-bars A06092 Chrome, dual 3 11/32" gauges for 1 1/4" T-bars MW 'DIGITAL SPEEDO' CLAMP & AUTOMETER BRACKETS These unique design Custom handlebar clamps feature a very small lighted digital speedo that can be switched from KPH into MPH and also gives trip and time.this digital speedo can be attached to the gear box speed sensor when ZPN 741469 adapter kit is used. Alternatively the included electronic wheel sensor can be used. The digital speedo is programmable for use with any wheel size by following the easy to read multi-lingual instructions. Clamps are CNC machined from billet aluminum and have a high-gloss polished finish. They are designed to take Auto Meter 2 5/8" or 3 3/4" tacho's. These "Digital Speedo" clamps look even greater when you also fit a pair of MW squared billet aluminum risers (ZPN 710399). Bracket with digital speedo 721831 For Auto Meter 2 5/8" 721832 For Auto Meter 2 5/8" and control lights 710418 For Auto Meter 3 3/4" 7104 For Auto Meter 3 3/4" and control lights Optional 710399 Squared billet aluminum 2 3/8" high risers -076

Speedo Mount MW NARROW CLAMP FOR 48 MM SPEEDO CUP These CNC machined aluminum custom handlebar clamps accept your choice of cup and MMB speedo, tacho, clock,voltmeter or instrument panel. Clamps are extra narrow to make them work with risers upto 50 mm in diameter. Clamps come with a cable opening, to route the internal handlebar wiring neatly through the clamp. The clamp is available in a version with three control light holes as well as without control light holes. 741231 Without control light holes 741232 With control light holes MW "DIGITAL SPEEDO" CUSTOM HANDLEBAR CLAMP & MINI METER BRACKETS These unique design, CNC machined billet aluminum Custom handlebar clampsfeature a very small lighted digital speedo that can be switched from KPH into MPH and also gives trip and time. All kits come with a electronic wheel sensor and can be programmed for use with any wheel size by following the easy to read multi-lingual instructions. Can also be connected to transmission mount electric speedo drive when ZPN 741469 adapter kit is used.these handlebar clamps are designed for use with MW meter brackets. Flat meter brackets fitted in an angle of 40 for excellent visibility.when you want the meters fitted flat you can use the 40 angle brackets. Meter brackets are available to take single or dual MMB mini meters such as tacho, Volt meter or mini instrument panel or Auto Meter tacho's. Handlebar clamps fit 73 to present Harley models models with 3 1/2" (89 mm) center-to-center risers with offset mounting holes. Note: All parts are sold separately, not as a kit. Note: All parts are sold separately, not as a kit. 710425 Handlebar clamp with digital speedo and control light holes 710435 Bracket for 40 angled mounting of dual 48 mm diameter instruments 710429 Cup with cable hole for 48 mm diameter cable driven speedo 710436 Cup for MMB or other 48 mm diameter tacho, clock,volt meter or instrument panel 741469 Digital speedo transmission adapter MW NARROW CLAMP FOR DUAL 48 MM SPEEDO CUPS These CNC machined aluminum custom handlebar clamps accept your choice of cups and MMB speedo, tacho, clock,voltmeter or instrument panel. Clamps are extra narrow to make them work with risers up to 50 mm in diameter. Clamps come with a cable opening, to route the internal handlebar wiring neatly through the clamp. The clamp is available in a version with three control light holes as well as without control light holes. 741233 Without control light holes 741234 With control light holes 710424 Handlebar clamp with digital speedo 710434 Bracket for 40 mounting of a single 48 mm diameter instrument 710436 Cup for MMB or other 48 mm diameter tacho, clock,volt meter or instrument panel 741469 Digital speedo transmission adapter -077

Speedo Mount MW CUSTOM HANDLEBAR CLAMP & MINI METER BRACKETS These MW Custom handlebar clamps are prepared for the use of MW's meter brackets for single or dual MMB meters and other 48 mm diameter instruments, or Auto Meter tacho's. All parts are CNC machined from billet aluminum and have a high-gloss polished finish.they fit most 73 to present Harley models with 3 1/2" (89 mm) centerto-center risers with offset mounting holes. Note: All parts are sold separately, not as a kit. 710427 Handlebar clamp with meter bracket recess and control light holes 710435 Bracket for 40 angled mounting of dual 48 mm diameter instruments 710429 Cup with cable hole for 48 mm diameter cable driven speedo 710436 Cup for MMB or other 48 mm diameter tacho, clock,volt meter or instrument panel Note: All parts are sold separately, not as a kit. 710426 Handlebar clamp with meter bracket recess 710434 Bracket for 40 mounting of a single 48 mm diameter instrument 710429 Cup with cable hole for 48 mm diameter cable driven speedo A. 710430 Bracket for flat mounting of a single 48 mm diameter instrument B. 710434 Bracket for 40 mounting of a single 48 mm diameter instrument A. 710432 Bracket for flat mounting of an Auto Meter tacho B. 710433 Bracket for 40 mounting of an Auto Meter tacho A. 710431 Bracket for flat mounting of dual 48 mm diameter instrument B. 710435 Bracket for 40 angled mounting of dual 48 mm diameter instruments Optional meter cups, must be used when installing MMB or other 48 mm diameter instruments 710429 Cup with cable hole for 48 mm diameter cable driven speedo 710436 Cup for MMB or other 48 mm diameter tacho, clock,volt meter or instrument panel 741230 Cup for MMB or other 48 mm diameter electronic speedo, must be ordered with 2 buttons of ZPN 370314 for speedo adjustments A. 721833 Cup with integrated bracket for flat mounting of 2 5/8" Auto Meter or other 67 mm diameter tacho B. 721834 Cup with integrated bracket for 40 angled mounting of 2 5/8" Auto Meter or other 67 mm diameter tacho -078

Speedo Mount MW BILLET ALUMINUM SPEEDO BRACKETS FOR T-BARS These billet aluminum speedo & tacho brackets are designed to bolt straight on to any 1" T-bar with stock center to center distance and take the 48 mm mini MMB meters.the rubber inserts that are integrated in the clamping section help to isolate your instruments from the bike's vibrations. No hardware exposed for a clean Custom look. Available for single or dual meters and with and without factory idiot lights and all beautifully high-gloss polished. 710440 Fits single mini meter PRO-MAX CHROME BILLET GAUGE MOUNTS FOR T-BARS Designed to bolt straight on to any 1" and 1 1/4" diameter T-Bar style handlebar and ready to take 48 mm diameter gauges. Available for use with a single or two gauges and plain or drilled to take 2 control lights. Gauges are secured with a hidden mount set screw for extra clean looks.a rubber o-ring in the gauge mounts helps to isolate meters from vibrations.all versions feature a showchrome finish and come complete with the necessary hardware. For use with a single gauge 169306 No control light holes 169307 With 2 control light holes For use with 2 gauges 169308 No control light holes 169309 With 2 control light holes 3-LIGHT SPEEDO AND TACHO MOUNTING BRACKET Show-chromed top quality mounting bracket fits FXR 84 thru 85, and Sportster and FX models with 3-light warning lamp assembly.these deep blue chromed brackets replace the OEM black finished bracket. Made from heavy gauge steel and perfectly formed (OEM 67036-83 & 67110-83T & 67089-85). 169152 Speedo/tacho bracket 710437 Fits single mini meter and control lights 4-LIGHT SPEEDO AND TACHO MOUNTING BRACKET The same top quality chrome plating and exacting fit as ZPN 169152, but machined for 86 to present models equipped with the 4-light warning lamp assembly (OEM 67036-86 & 67161-86 & 67110-86). 169158 Speedo/tacho bracket 710438 Fits dual mini meters 710439 Fits dual mini meters and control lights FAT BUBBA T-BAR METER BRACKET Aluminum mounting bracket with show chrome finish. Features two threaded holes to fit gauges or other accessories. Fits applications with 1 1/4" thick T-bars or 1 1/4" thick risers and 3 1/2" center-to-center distance. 061231 T-Bar gauge mounting bracket 4-LIGHT SOLO SPEEDO BRACKET Chrome plated gauge bracket for replacing the black finished OEM bracket on all XL 83 thru 94 and FXR 84 thru 94 with single instrument.the all steel bracket wraps over the upper rim of the instrument reducing glare and adding a functional, gleaming chrome highlight. Accepts the late model 4-lite warning lamp assembly (OEM 67053-86). 301669 Speedo support -079

Speedo Mount/Speedo Accessories SPEEDOMETER BRACKET FOR SPORTSTER AND DYNA This speedometer bracket bolts to the stock handlebar clamp on 95 to present XL 883 Sportster and 95 thru 2004 FXD Super Glides.Also fits 2004 to present Dyna models when installed in conjunction of an aftermarket handlebar clamp. Takes all speedo's with 3 1/2" (89 mm) housing, reffered by Harley as 4" gauges. Has five control light holes. 169387 Chrome (OEM 67293-95) 169388 Black (OEM 67053-95) CAFE RACER HEADLIGHT RE- LOCATOR Roland Sands Design Café Gauge and Headlight Re-locator eliminates the stock headlight visor and lowers your headlight and gauges to a more sleek position from the top handlebar clamp down to the front of the top triple clamp and lowers the stock headlight 2 inches. This allows for the use of any aftermarket risers or complete elimination of risers for use of the RSD Café 39 mm Clip- Ons. The re-locator does not take the stock warning lights. Billet aluminum construction, available in chrome and black. Fits all 2008 to present XL Sportster models. Speedo and indicator light not included. 740890 Black 740891 Chrome 740923 LED Indicator light unit SPEEDO SOCKET WITH BULB Speedo light socket complete with 12 Volt bulb. Fits all Zodiac speedo's as well as the OEM FL style speedo's (OEM 71151-70). 169062 Speedo light socket ANTIQUE SPEEDO KNOB A reproduction of the thin stem speedometer/odometer reset knob for Big Twin speedometers. Must be used when installing a stamped steel two-light, threelight or cat-eye dash, because of the narrower reset knob opening (10 pack). 169098 Antique speedo CHROME DUAL SPEEDO TACHO VISOR A chrome plated instrument backing plate and visor fits all dual handlebar mounted instruments models 84 thru 88 (except FXLR). Mounts easily beneath the standard equipment mounting bracket. The visor provides a better, clear, glare-free observation of the instruments and warning lamps. A perfect combination with our 3- and 4-light speedo tacho mounting brackets. 169151 Chrome dual speedo tacho visor ODOMETER RESET CABLE FOR HARLEY FX Complete odometer reset cable assembly for all 4 Speed FX models (except FXWG) 73 thru 84. Includes all necessary parts and is fully assembled (OEM 67210-73). 110053 Odometer reset cable CHROME SPEEDO-METER KNOB Long, fits all Softail models from 90 to present (OEM 6721589). Short, Fits FXLR models from 84 thru 94 (OEM 67108-83). 116043 Long, fits all Softail models from 90 to present (OEM 6721589) 116044 Short, Fits FXLR models from 84 thru 94 (OEM 6710883) RUBBER BOOT FOR SPEEDO- METER CABLE Made from black flexible rubber, protects your cable and drive unit from harmful dirt, dust and moisture. Sold in shop packs of 10. 116041 Speedo cable rubber boot SPEEDO-METER KNOB AND SCREW Replacement knob and screw set for large, dash mounted speedometers as used on FX 71 thru 72, FXWG-FXST 80 thru 87 and FL 68 thru 84. 116042 Speedometer know and screw -080

Drive Unit & Cable TRANSMISSION DRIVEN SPEEDO CABLES Available in black vinyl, braided stainless steel and Clear Coated braided stainless steel. Fits all 62 thru 80 FL, 71 thru 72 FX and 80 thru 83 FXWG. Also fits 54 thru 72 XL when one piece Fat Bob tank with FL style speedo is used. Stock length is 35" (89 cm). Black Vinyl Black Vinyl 114030 Stock length 114031 4" longer than stock 114236 6". longer than stock 114032 12" longer than stock Braided Stainless Steel 114235 Stock length Clear Coated Braided Stainless Steel 114932 Stock length 114930 4" longer than stock 114931 12" longer than stock Fits all transmission driven Zodiac mini speedo's, cable is 53" (135 cm) long 114017 Black vinyl 1145 Braided steel 114929 Clear Coated braided Stainless Steel CUSTOM FRONT WHEEL DRIVEN SPEEDO METER CABLE This unique front wheel drive speedo cable allows you to combine any of our large FL style 2:1 speedometers, including our latest FL style speedo with built-in tacho. Each cable comes complete with 2 cable to speedo head nuts to fit either the large FL speedo with 5/8" fitting or the 82 and later style metal cased FX/XL speedo with 16 mm fitting. Also replaces the OEM cable on 84 FXWG and FXST. May be used on 41 thru 84 FL models with front wheel driven speedometers and when our Fat Bob style tank is installed on the FXR and XL models. Stock length is 38 1/2" (98 cm). Black Vinyl 114152 Stock length 114246 4" (10 cm) longer than stock Braided Stainless Steel 114248 Stock length 114242 4" (10 cm) longer than stock Clear Coated Stainless Steel 114935 Stock length 114934 4" (10 cm) longer than stock SPEEDO DRIVE UNITS Perfect replica of the OEM speedo drive units. These units work with any of our 2-to-1 ratio speedo's. 116032 Fits FX 73 thru 80 and XL 74 thru 83 with " Narrow Glide front wheels (OEM 67127-73) 116036 Fits FXE/FXS 80 thru 84 and FXR thru 84 (OEM 67124-80) 116028 Fits FL models 81 thru 84, FLT/FLHT 82 thru 86 (OEM 67073-81) 116030 Fits FXWG/FXST/FXSTC/FLSTF 84 to present, with 21" front wheel (OEM 67120-84B) 116034 Fits FXR/FXRS/XL 84 to present with " Narrow Glide front SPEEDOMETER DRIVE ASSEMBLY FOR 45 C.I MODELS A perfect reproduction of the rear wheel speedometer drive,as used on the 45 C.I.side valve solo models from 37 thru 52. Has a chrome finish (OEM 67129-37). 116048 Speedo drive gear -081

Drive Unit & Cable Fits XLH/XLCH 74 thru 83, XLS 79 thru 82, FXWG/FXST 85 thru 95, FXR 82 thru 83 and all front wheel driven Zodiac & MMB mini speedo's. Stock cable is 38 1/2" (98 cm) long TRANSMISSION DRIVEN SPEEDO METER DRIVE UNIT Perfect replica of the OEM transmission speedometer drive units as used on FL models from 69 thru 80, FX models from 70 thru 72 and FXWG models from 80 thru 83 (OEM 67130-69). 116040 Speedometer drive unit REAR WHEEL SPEEDO DRIVE KIT FOR SOFTAIL This is the ultimate accessory when you want to have a clean front end on your pre 95 Softail.Can also be used on other front wheel drive models with 16" rear wheel and tank mounted speedo.this kit eliminates the need of the front wheel speedo drive and "Always in the Way" speedo cable running from the front wheel to the tank mounted speedo. Our Rear Wheel Speedo Drive Kit includes a rear wheel speedo drive unit with chrome plated cover,a 72 1/2" black vinyl speedo drive cable with 12 mm speedometer connector, a zinc coated bushing to replace the front wheel speedo drive unit and all other required hardware for a quick and easy do-it-yourself job, fits Softail models 86 thru 95. This kit is mounted on the left side of the motorcycle. 116045 Complete kit FRONT WHEEL DRIVE SPEEDO CABLES Available in black vinyl, braided Stainles Steel and Clear Coated braided Stainless Steel. Fits FX models 73 thru 85 (except FXWG/FXST), FXRS/FXRT 84 to present, XLX/XLCH 73, XLX/XLS 83 thru 85 and Evolution Sportster models 86 thru 95. Stock cable is 38 1/2" (98 cm) long. Black vinyl 114003 Stock length, black vinyl (OEM 67051-73 & 67052-78A) 114155 4" (10 cm) longer than stock (OEM 67054-83) 114135 6" (15 cm) longer than stock 114001 8" (20 cm) longer than stock Braided Stainless Steel 114264 Stock length 114269 4" (10 cm) longer than stock Clear Coated braided Stainless Steel 114915 Stock length, black vinyl (OEM 67051-73 & 67052-78A) 114916 4" (10 cm) longer than stock (OEM 67054-83) 114917 6" (15 cm) longer than stock 114918 8" (20 cm) longer than stock Black vinyl 114006 Stock length (OEM 67051-74 & 67024-84 & 67038-84) 114147 4" (10 cm) longer than stock (OEM 67060-79A) 114137 6" (15 cm) longer than stock 114000 8" (20 cm) longer than stock Braided Stainless Steel 114099 Stock length (OEM 67051-74 & 67024-84 & 67038-84) 114274 4" (10 cm) longer than stock 114277 6" (15 cm) longer than stock Clear Coated Braided Stainless Steel 114920 Stock length (OEM 67051-74 & 67024-84 & 67038-84) 114921 4" (10 cm) longer than stock (OEM 67060-79A) 114922 6" (15 cm) longer than stock 114923 8" (20 cm) longer than stock Fits front wheel drive FL(T)(TC) 81 thru 86 Black Vinyl 114033 Standard length (OEM 67026-81) Clear Coated braided Stainless Steel 114927 Standard length Optional and replacement parts 114570 Speedo cable, black vinyl 114928 Optional Clear Coated braided stainless steel speedo cable 116060 Speedo drive unit 301855 Chrome speedo drive unit cover -082

Drive Unit & Cable CHROME SPEEDO DRIVE COVERS The finishing touch for your front end. Available to fit virtually every speedometer drive unit used since 73, and designed to clear the Original Equipment black rubber cable boot. 301857 Fits all Sportster, FX and FXR models with 35 mm front forks (except XR 1000) from 73 thru 83, 4 Speed FL models from 81 thru 84 as well as FL(H)T models from 82 thru 86 301856 Fits 83 XR 1000 as well as all narrow glide models from 84 to present 301855 Chrome speedo drive unit cover SPEEDOMETER BLOCK OFF KITS Made by James Gaskets from metal inserted black neoprene to plug off the speedometer cable or sensor hole in Big Twin 4 or 5-speed transmission. Plugs come complete with stainless steel screw and washer. 231674 Fits all Big Twin 4-speed transmissions 231675 Fits all Big Twin 5-speed transmissions ELECTRONIC SPEED SENSORS Transmission mounted OEM equipment speed sensor.available for Sportster and Big Twin models. Speed sensors will also fit Zodiac 5 and 6 speed transmissions, all ECOline 5 and 6 speed transmissions, as well as most other aftermarket 5 and 6 speed transmissions, including Right Side Drive transmissions. 237509 Speed sensor 96-99 720179 Speed sensor 744491 Fits Softail 2000 thru 2006 and FLH/FLT series models 2000 thru 2006 (OEM 74430-00D) 744487 Fits 95 thru 2004 Sportster (OEM 74402-95B) 744492 Fits 2005 to present Sportster, 2006 to present Dyna, 2007 to present Softail and 2007 to present FLH and FLT series models (OEM 74402-05) CHROME BILLET SPEED SENSOR COVER Chrome plated billet aluminum cover to cover the black plastic speed sensor of the transmission. Fits 95 to present Sportsters, all 94 thru 99 Evolution Big Twins and 99 to present Twin Cams. 169228 Chrome speed sensor cove CABLE GUIDE BRACKET Chrome plated bracket used as a cable guide for routing clutch or speedo cables on many Harley models.also usable as gas line routing or tie-down/bungee cord bracket. Sold in 10 pack (OEM 38623-68). 090067 Cable guide bracket SPEEDO CABLE MOUNTING CLIP FOR FL-FX Stainless Steel mounting clip. Used on transmission driven, dash mounted speedo. For routing the speedo cable, mounts under the case stud nut in between the cylinders (OEM 67075-57A). 114185 Speedo cable mounting clip BILLET ALUMINUM SPEEDO CABLE GUIDE BY PRO-ONE Don't let your speedo cable scratch your paint. Install this billet speedo cable guide and sleep better at night. Can be used on any models. 237857 Speedo cable guide chrome -083

Indicator Light INDICATOR LIGHTS OEM type indicator lights for 5/16" holes. Oil indicator shows a red lighted oil canister icon, High Beam a blue high beam icon, Neutral indicator a green "N", and turn signal indicators show a green arrow.the red pursuit indicator has no icon. Stock replacement for most models. Will also fit most aftermarket brackets and handlebar clamps such as our MW speedo meter brackets and handlebar clamps. Red and green lights are also available with no icons and a chrome trim. A.High beam indicator light, blue (OEM 68023-92A) 160902 Headlamp and beam icon, black trim B. Oil indicator light, red (OEM 68020-92A) 160900 Oil can icon, black trim 162141 Plain, chrome trim C. Turn signal indicator light, green (OEM 68021-92A) 160901 Arrow icon, black trim 162139 Plain, chrome trim D. Neutral indicator light, green (OEM 68024-92A) 160904 N icon, black trim 162139 Plain, chrome trim E.Pursuit indicator light, red (OEM 68022-92A) 160903 Plain, black trim 162141 Plain, chrome trim LED INDICATOR LIGHTS These LED indicator lights fit 5/16" (8 mm) holes as used in most dashes, control light panels and handlebar clamps.they have a stainless steel bezel and come with 30" (76 cm) leads. Sold each. 162605 Clear lens LED indicator light 162606 Blue lens LED indicator light 162607 Green lens LED indicator light 162608 Red lens LED indicator light 162609 Amber lens LED indicator light -084