INSTALLATION GUIDE. Directed Digital Solutions HKHT1. Designed by Installers for Installers

INSTALLATION GUIDE Directed Digital Solutions HKHT1 Designed by Installers for Installers 2018 Directed, Vista CA This product is intended for installation by a professional installer only! Attempts to install this product by a person other than a trained professional may result in severe damage to a vehicle s electrical system and components. 2018-03-16

Contents Warning! Safety first... 3 Introduction... 4 Pre-installation and application warnings... 4 Vehicle application guide... 5 Wiring connections... 6 Main power harness (H1), 12-pin thick gauge connector... 6 Auxiliary output harness (H2), 16-pin black connector... 6 Analog harness (H3), 18-pin white connector... 7 MC501 harness (H4), 8 thick-gauge wires (optional)... 7 Installation (wiring diagrams & vehicle wiring reference charts)... 8 Type 1 with T-Harness (THHYC3)... 8 Type 1... 9 Type 2 with T-Harness (THHYC3)... 13 Type 2... 14 Type 3 with T-Harness (THHYC3)... 19 Type 3... 20 Type 4 with T-Harness (THHYC3)... 23 Type 4... 24 Type 5 with T-Harness (THHYC3)... 27 Type 5... 28 Connecting the module... 31 Important!... 31 Manual or automatic transmission selection... 31 Optional sensors... 32 RF Systems... 32 When used in conjunction with SmartStart... 32 Module programming... 33 Method 1: Module programming with CAN connections and with transponder immobilizer... 33 Method 2: Module programming without CAN connections and with transponder immobilizer... 34 Method 3: Module programming with CAN connections and without transponder immobilizer... 35 LED diagnostics and troubleshooting... 36 Soft reset... 38 Hard reset... 38 Learning the Tach (not needed with Virtual Tach)... 39 Initializing Virtual Tach (not needed with hardwired or data tach applications)... 39 Limited lifetime consumer warranty... 40 Quick Reference Guide... 41

Warning! Safety first The following safety warnings must be observed at all times: Due to the complexity of this system, installation of this product must only be performed by an authorized Directed dealer. When properly installed, this system can start the vehicle via a command signal from the remote control. Therefore, never operate the system in an area that does not have adequate ventilation. The following precautions are the sole responsibility of the user; however, authorized Directed dealers should: Never use a test light or logic probe when installing this unit. Always use a multimeter. Never operate the system in an enclosed or partially enclosed area without ventilation (such as a garage). When parking in an enclosed or partially enclosed area or when having the vehicle serviced, the remote start system must be disabled using the installed toggle switch. It is the user s sole responsibility to properly handle and keep out of reach from children all remote controls to assure that the system does not unintentionally remote start the vehicle. USER MUST INSTALL A CARBON MONOXIDE DETECTOR IN OR ABOUT THE LIVING AREA ADJACENT TO THE VEHICLE. ALL DOORS LEADING FROM ADJACENT LIVING AREAS TO THE ENCLOSED OR PARTIALLY ENCLOSED VEHICLE STORAGE AREA MUST REMAIN CLOSED AT ALL TIMES. Use of this product in a manner contrary to its intended mode of operation may result in property damage, personal injury, or death. Except when performing the Safety Check outlined in this installation guide, (1) Never remotely start the vehicle with the vehicle in gear, and (2) Never remotely start the vehicle with the keys in the ignition. The user is responsible for having the neutral safety feature of the vehicle periodically checked, wherein the vehicle must not remotely start while the car is in gear. This testing should be performed by an authorized Directed dealer in accordance with the Safety Check outlined in this product installation guide. If the vehicle starts in gear, cease remote start operation immediately and consult with the user to fix the problem immediately. OPERATION OF THE REMOTE START MODULE IF THE VEHICLE STARTS IN GEAR IS CONTRARY TO ITS INTENDED MODE OF OPERATION. OPERATING THE REMOTE START SYSTEM UNDER THESE CONDITIONS MAY RESULT IN PROPERTY DAMAGE OR PERSONAL INJURY. IMMEDIATELY CEASE THE USE OF THE UNIT AND REPAIR OR DISCONNECT THE INSTALLED REMOTE START MODULE. DIRECTED WILL NOT BE HELD RESPONSIBLE OR PAY FOR INSTALLATION OR REINSTALLATION COSTS. Remote starters for manual transmission pose significant risks if not properly installed and operated. When testing to ensure the installation is working properly, only remote start the vehicle in neutral gear, on a flat surface and with a functional, fully engaged parking brake. Do not allow anyone to stand in front of or behind the vehicle. This product should not be installed in any convertible vehicles, soft or hard top with a manual transmission. Installation in such vehicles may pose certain risk. 3 Directed Digital Solutions HKHT1

Introduction The HKHT1 firmware for Directed Digital Solutions is compatible with specific Hyundai and Kia vehicles. It is a complete solution for remote start, security (if applicable), bypass interface, and convenience. This guide provides information on the installation of the module using HKHT1. If you would prefer using this system as a digital solution, go to www.directechs.com and search for the make, model and year of the vehicle. This will allow you to find the proper firmware and corresponding installation guide. Warning! This module can only be programmed via the web tool, which can be found on www.directechs.com or using the Directechs Mobile application for mobile devices. Features and functions will become accessible when you connect the module using the XKLoader. Pre-installation and application warnings Firmware notes: This section highlights important information for this specific firmware and will assist in pricing accordingly, as well as bringing awareness to any operational or vehicle limitations. T-Harness compatible THHYC3 Keys required for programming 1 Keys required for operation 0 Important! If your vehicle is NOT equipped with transponder immobilizer AND also does not use CAN's connections, then please flash your module with an analog firmware. The optional Plug & Play THHYC3 T-Harness is sold separately. The OBDII Diagnostic features will remain the same even when the T-Harness is installed. Unless specified otherwise, all connectors are displayed from the wire side, with the exception of the OBDII diagnostic connector. Refer to the "Vehicle wiring reference chart" following each installation type. General notes: This section highlights important information for this specific firmware. [1] The installation of an aftermarket hood pin is ONLY required on vehicles that are NOT equipped with a factory hood pin. [2] The siren is ONLY required when enabling the security features during module flashing. [3] The Green wire is ONLY required for starter disable and antigrind applications. [4] EMS COM connections ONLY needed if vehicle has a transponder immobilizer. [5] Required ONLY if RAP Off does not operate over data. Additional parts required (maximum required): 87 Diode 6A 0 x 1A Diodes 87a 86 30 85 0 x Relay esistor 100 0 x Resistor Fuse 7.5A 0 x Fuse 4 Directed Digital Solutions HKHT1

Vehicle application guide The following table lists the vehicles and features which are compatible with this product. The number assigned to each year allows you to determine which installation type should be used for your vehicle. Vehicles 2017 2016 2015 2014 2013 2012 2011 2010 2009 2008 PK-Immobilizer Bypass-Data No Key Req'd DL-Arm Factory Security DL-Disarm Factory Security DL-Door Lock Control Hyundai Accent 3 3 3 3 3 3 Accent 2 2 2 2 Elantra 1 1 1 1 1 1 Elantra 2 2 2 Elantra Coupe 1 1 Elantra Touring 3 3 3 3 Genesis Coupe 2 2 2 Santa Fe 3 3 3 3 3 Sonata 1 1 1 1 Sonata 2 2 2 Tucson 1 1 1 1 1 1 Kia 17 16 15 14 13 12 11 10 09 08 Forte 4 4 4 4 Forte5 4 4 4 Magentis 2 2 Optima 1 1 1 1 1 Optima 2 2 2 Rio 2 2 2 2 Rondo 3 3 3 3 3 Sorento 5 5 5 5 5 Soul 4 4 4 4 Sportage 1 1 1 1 1 1 Sportage (4-cylinder) 2 2 2 Sportage (V6) 2 2 2 Legend: PK: Transponder & Immobilizer Override DL: OE Door Lock & Alarm Controls FOB: Sync CAN Interface w/ FOB Remote RS: Remote Start & Engine Controls SS: Integrated Security & Monitoring ST: Function/Feature Status DL-Door Unlock DL-Driver Priority Unlock DL-Trunk / Hatch Release FOB-Control of aftermarket alarm with OEM remote RS-RAP Shut Down (Retained ACC Power) RS-Remote Start Takeover RS-SmartStart RS-Tach / RPM Output SS-Entry Monitoring ALL Door Pins SS-Entry Monitoring Hood Pin SS-Entry Monitoring Trunk/Hatch Pin SS-Factory Alarm Trigger Monitoring ST-Brake Status (foot brake) ST-Door Locks Status ST-E-Brake Status 5 Directed Digital Solutions HKHT1

Wiring connections The wiring connections listed below are specific to this firmware. Main power harness (H1), 12-pin thick gauge connector Conn./Pin Color Description H1/1 White Relay 3 COM No Connection 1 H1/2 White/Brown Relay 3 N.O. No Connection 1 H1/3 Brown/Red Relay 2 N.O. No Connection H1/4 Yellow/Red Relay 2 COM No Connection H1/5 Orange/Red Relay 2 N.C. No Connection H1/6 Yellow Relay 1 COM EMS COM Data (Vehicle side) 1 H1/7 White Relay 3 COM No Connection 1 H1/8 White/Brown Relay 3 N.O. No Connection 1 H1/9 Black (-) Ground H1/10 Red (+) 12 Volt (Battery) H1/11 Orange/Yellow Relay 1 N.C. EMS COM Data (connector side) 1 H1/12 Brown Relay 1 N.O. No Connection 1 Auxiliary output harness (H2), 16-pin black connector Conn./Pin Color Description H2/1 Violet/Brown No Connection H2/2 Yellow/Black EMS COM Data ( side) H2/3 Orange/Black EMS COM Data (Vehicle side) H2/4 Tan HS CAN Low H2/5 Tan/Black HS CAN High H2/6 Light Green No Connection H2/7 Orange/Green FT CAN High H2/8 Orange/Brown FT CAN Low H2/9 Violet/Green No Connection H2/10 Green/Black (-) Parking Light Output 2 H2/11 White/Violet (-) RAP Off Output 2 H2/12 White/Red No Connection 2 H2/13 Lt. Blue/Black No Connection 2 H2/14 Green/Red No Connection 2 H2/15 N/A No Connection H2/16 Violet/Yellow No Connection 1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 2. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 6 Directed Digital Solutions HKHT1

Analog harness (H3), 18-pin white connector Conn./Pin Color Description H3/1 Lt. Blue/Red No Connection H3/2 Black/White (-) Parking Brake Input (Manual Transmission) 2 H3/3 Gray (-) Hood Input 2 H3/4 N/A No Connection H3/5 Gray/Black (+) Glow Plug Input 2 H3/6 Violet/White (AC) Tach Input 2 H3/7 Dark Blue (-) Unlock Output 1 H3/8 Brown/Black (-) Horn 1 H3/9 Red/White (-) Trunk Release Output 1 H3/10 White/Green No Connection 2 H3/11 Yellow/Green (+) Door Input 2 H3/12 Blue/Red No Connection H3/13 Light Blue (-) Trunk Trigger Input 2 H3/14 Pink/Yellow (-) Activation (Start Trigger) Input H3/15 Dark Green (-) Lock Output 1 H3/16 Brown/White (+) Brake Input 2 H3/17 Brown (+) Siren Output 1 H3/18 Blue/White (-) Ground When Running (Status) Output 1 MC501 harness (H4), 8 thick-gauge wires (optional) Conn./Pin Color Description H4/1 Pink/White (+) Ignition 2/Flex Relay Output 3 H4/2 Red/White (+) Fused (30A) Ignition 2/Flex Relay Input H4/3 Pink (+) Ignition Output (Also Input to Yellow in Ribbon Cable) H4/4 Red (+) 12 Volt (Battery) Input H4/5 Orange (+) Accessory Output H4/6 Red (+) 12 Volt (Battery) Input H4/7 Green Starter Input (From Key Switch) 4 H4/8 Violet (+) Starter Output (To Starter) 1. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. Note that they are low current and a relay may be necessary. 2. These connections are only required if the corresponding statuses are not supported by the firmware. See "Vehicle application guide" on page 5 for a list of compatible features. 3. If these outputs are not used by the firmware, they can be configured by the installer when the module is flashed. 4. The Green wire is only required for starter disable and anti-grind applications. 7 Directed Digital Solutions HKHT1

Installation (wiring diagrams & vehicle wiring reference charts) Type 1 with T-Harness (THHYC3) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). Parking Lights EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires Refer to the Vehicle wiring reference chart. (-) Parking Light Output: Green/Black Ignition Switch EMS COM connections only needed if vehicle has transponder/immobilizer. EMS COM Data (veh. side): Orange/Black EMS COM Data (veh. side): Yellow EMS COM Data (conn. side): Yellow/Black EMS COM Data (conn. side): Orange/Yellow Remote Start Safety Override Switch B-CAN Wires FT CAN Low: Orange/Brown FT CAN High: Orange/Green 2-pin Black The Remote Start Safety Override Switch MUST be in the ON position. See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. 16-pin Black THHYC3 (Optional T-Harness) OBDII - Diagnostic 16-pin Conn. Hood Pin (-) Hood Input: Gray: 3 Siren (+) Siren Output: Brown: 17 12-pin White Diagnostic OBDII 8 Directed Digital Solutions HKHT1

Type 1 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Diagnostic Conn. OBDII C-CAN High: pin 6 1 9 8 16 C-CAN wires MUST be connected for proper operation. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires EMS COM connections only needed if vehicle has transponder/immobilizer. C-CAN Low: pin 14 Ignition, Accessory, Starter & (+) 12V wires at ignition switch, 6-pin connector EMS COM Data (conn. side): Yellow/Black: 2 EMS COM Data (veh. side): Orange/Black: 3 HS CAN Low: Tan: 4 Refer to the Vehicle wiring reference chart. (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) 12V Input: Red (+) Accessory Output: Orange (+) 12V Input: Red 8 thick-gauge wires MC501 4 White 7 White HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Light Output: Green/Black: 10 B-CAN Wires & Parking Lights See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink Hood Pin (-) Hood Input: Gray: 3 11: Orange/Yellow: EMS COM Data (conn. side) 10: Red: (+) 12V (+) 12V 9: Black: (-) Ground (+) Siren Output: Brown: 17 6: Yellow: EMS COM Data (veh. side) Refer to the Vehicle wiring reference charts for wire and connector details related to the standard connections in the vehicle. Siren 9 Directed Digital Solutions HKHT1

Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information. Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Hyundai Elantra 2011-2013 12V Green 1 (+) Ignition switch. White 6 A Accessory Orange 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Yellow 3 (+) Ignition switch. White 6 A Parking Lights Pink 2 (-) Headlight switch. White 10 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B B-CAN High White/Orange or Brown 13 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D B-CAN Low Yellow/Orange or White 1 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D EMS COM Blue or Blue/Orange 10 Data Driver kick panel, EM11 (Conn. 1*, Connection Type A**). White 55 E Hyundai Elantra 2014-2016 12V Green 1 (+) Ignition switch. White 6 A Accessory Orange 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Yellow 3 (+) Ignition switch. White 6 A Parking Lights Pink 2 (-) Headlight switch. White 10 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B B-CAN High Green or Brown 13 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D B-CAN Low Orange or White 1 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D EMS COM Blue 12 Data Driver kick panel, EM11 (Conn. 7*, Connection Type A**). White 58 E Hyundai Elantra Coupe 2013 12V Green 1 (+) Ignition switch. White 6 A Accessory Orange 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Yellow 3 (+) Ignition switch. White 6 A Parking Lights Pink 2 (-) Headlight switch. White 10 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B B-CAN High White/Orange or Brown 13 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D B-CAN Low Yellow/Orange or White 1 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D EMS COM Blue 10 Data Driver kick panel, EM11 (Conn. 6*, Connection Type A**). White 55 E 10 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Hyundai Elantra Coupe 2014 12V Green 1 (+) Ignition switch. White 6 A Accessory Orange 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Yellow 3 (+) Ignition switch. White 6 A Parking Lights Pink 2 (-) Headlight switch. White 10 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B B-CAN High Green or Brown 13 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D B-CAN Low Orange or White 1 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D EMS COM Blue 10 Data Driver kick panel, EM11 (Conn. 6*, Connection Type A**). White 55 E Hyundai Sonata 2011-2014 12V Green 1 (+) Ignition switch. White 6 A Accessory Orange 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Yellow 3 (+) Ignition switch. White 6 A Parking Lights Pink 2 (-) Headlight switch. White 10 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B B-CAN High White/Orange or Blue 12 Data Junction Box (Rear), I/P-F (Conn. 2*). White 24 D B-CAN Low Yellow/Orange 11 Data Junction Box (Rear), I/P-F (Conn. 2*). White 24 D EMS COM Blue or Blue/Black 10 Data Driver kick panel, EM11 (Conn. 8*, Connection Type A**). White 43 E Hyundai Tucson 2010-2015 12V Red 1 (+) Ignition switch. White 6 A Accessory Blue 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Green 3 (+) Ignition switch. White 6 A Parking Lights Yellow 1 (-) Headlight switch. White 10 C C-CAN High Green 6 Data OBDII. Black 16 B C-CAN Low Orange 14 Data OBDII. Black 16 B B-CAN High Blue 8 Data Instrument Cluster, M115-A (Conn. 3*). White 24 G B-CAN Low Red 9 Data Instrument Cluster, M115-A (Conn. 3*). White 24 G EMS COM Blue 1 Data Driver kick panel, MC41 (Conn. 9*, Connection Type B**). White 15 E Kia Optima 2011-2013 12V Green 1 (+) Ignition switch. White 6 A Accessory Orange 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Yellow 3 (+) Ignition switch. White 6 A Parking Lights Pink 1 (-) Headlight switch. White 13 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B B-CAN High White/Orange 25 Data Junction Box (Rear), I/P-E (Conn. 4*). White 39 D B-CAN Low Yellow/Orange 38 Data Junction Box (Rear), I/P-E (Conn. 4*). White 39 D EMS COM Blue 10 Data Driver kick panel, EM11 (Conn. 8*, Connection Type B**). White 43 E 11 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Kia Optima 2014-2015 12V Green 1 (+) Ignition switch. White 6 A Accessory Orange 2 (+) Ignition switch. White 6 A Ignition Pink 4 (+) Ignition switch. White 6 A Starter Yellow 3 (+) Ignition switch. White 6 A Parking Lights Pink 1 (-) Headlight switch. White 13 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B B-CAN High White/Orange 13 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D B-CAN Low Yellow/Orange 1 Data Junction Box (Rear), I/P-G (Conn. 1*). White 24 D EMS COM Blue 41 Data Driver kick panel, EM11 (Conn. 7*, Connection Type A**). White 58 E Kia Sportage 2011-2016 12V Red 1 (+) Ignition switch. White 6 A Accessory Blue 2 (+) Ignition switch. White 6 A Ignition Green 4 (+) Ignition switch. White 6 A Starter White 3 (+) Ignition switch. White 6 A Parking Lights Blue 1 (-) Headlight switch. White 13 C C-CAN High Green 6 Data OBDII. Black 16 B C-CAN Low Orange 14 Data OBDII. Black 16 B B-CAN High Blue 20 Data Junction Box (Right), JM01 (Conn. 5*). Black 20 D B-CAN Low Red 10 Data Junction Box (Right), JM01 (Conn. 5*). Black 20 D EMS COM Blue 7 Data Passenger kick panel, MC11 (Conn. 10*, Connection Type A**). Yellow 24 F *See below for a visual representation of each connector. **See EMS COM Connection Types on Installation Wiring Diagram. images All adapters are displayed from the wire side (unless specified otherwise) All adapters are displayed from the wire side (unless specified otherwise). 1 - I/P-G, White 24-pin 2 - I/P-F, White 24-pin 3 - M115-A, White 24-pin 1 13 11 12 8 9 4 - I/P-E, Black 39-pin 5 - JM01, Black 20-pin 6 - EM11, White 55-pin conn. 39 38 37 36 35 34 33 32 31 30 29 28 27 25 24 23 22 21 20 19 18 17 16 15 26 14 13 12 11 10 9 8 7 6 5 4 3 2 1 10 20 10 7 - EM11, White 58-pin conn. 8 - EM11, White 43-pin conn. 9 - MC41, Blue 15-pin conn. 10 - MC11, Yellow 24-pin conn. 41 10 1 7 12 12 Directed Digital Solutions HKHT1

Type 2 with T-Harness (THHYC3) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires Ignition Switch EMS COM connections only needed if vehicle has transponder/immobilizer. EMS COM Data (veh. side): Orange/Black EMS COM Data (veh. side): Yellow EMS COM Data (conn. side): Yellow/Black EMS COM Data (conn. side): Orange/Yellow Remote Start Safety Override Switch (-) Lock Output: Dk. Green (-) Unlock Output: Dk. Blue Refer to the Vehicle wiring reference chart section for corresponding connector, pin and wire color of your vehicle. (-) RAP Off Output: White/Violet (-) Parking Light Output: Green/Balck (-) Trunk Release Output: Red/White (+) Brake Input: Brown/White 16-pin Black 2-pin Black THHYC3 (Optional T-Harness) The Remote Start Safety Override Switch MUST be in the ON position. OBDII - Diagnostic 16-pin Conn. Hood Pin (-) Hood Input: Gray: 3 Siren (+) Siren Output: Brown: 17 12-pin White Diagnostic OBDII 13 Directed Digital Solutions HKHT1

Type 2 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires C-CAN wires MUST be connected for proper operation. EMS COM connections only needed if vehicle has transponder/immobilizer. Diagnostic Conn. OBDII (wire side view) C-CAN High: pin 6 1 9 8 16 EMS COM Data (conn. side): Yellow/Black: 2 C-CAN Low: pin 14 (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) 12V Input: Red (+) Accessory Output: Orange (+) 12V Input: Red 8 thick-gauge wires MC501 4 White 7 White Hood Pin EMS COM Data (veh. side): Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (-) Parking Light Output: Green/Black: 10 (-) RAP Off Output: White/Violet: 11 (-) Hood Input: Gray: 3 (-) Unlock Output: Dark Blue: 7 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (-) Trunk Release Output: Red/White: 9 (-) Lock Output: Dark Green: 15 11: Orange/Yellow: EMS COM Data (conn. side) 10: Red: (+) 12V (+) Brake Input: Brown/White: 16 9: Black: (-) Ground (+) Siren Output: Brown: 17 6: Yellow: EMS COM Data (veh. side) Ignition, Accessory, Starter & (+) 12V wires at ignition switch, 6-pin connector Siren Refer to the Vehicle wiring reference chart. Refer to the Vehicle wiring reference chart. 14 Directed Digital Solutions HKHT1

Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information. Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Hyundai Accent 2008-2011 12V Green 5 (+) Ignition switch. White 6 A Accessory Orange 3 (+) Ignition switch. White 6 A Ignition Pink 6 (+) Ignition switch. White 6 A Starter White 1 (+) Ignition switch. White 6 A C-CAN High Red 6 Data OBDII. Black 16 B C-CAN Low Blue 14 Data OBDII. Black 16 B Lock Blue 6 (-) Dash fuse box. White 16 C Unlock Yellow/Black 16 (-) Dash fuse box. White 16 C Brake Green 2 (+) Dash fuse box. Gray 18 C Parking Lights Red or Pink/ Black 10 (-) Drivers kick panel. Blue 20 E EMS COM Blue/Black 15 Data Left of Junction Box, EM01 (Conn. 1*, Connection Type A**). Black 39 G Drivers Door Green 2 (-) Drivers kick panel. Blue 42 E Hyundai Elantra 2008-2010 12V Black 5 (+) Ignition switch. White 6 A Accessory White or Orange 3 (+) Ignition switch. White 6 A Ignition White/Blue or Blue 6 (+) Ignition switch. White 6 A Starter Black/Yellow or White 1 (+) Ignition switch. White 6 A Parking Lights Orange 8 (-) Headlight switch. White 14 F C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B Brake Black 34 (+) Drivers kick panel. Gray 39 E Drivers Door Red 36 (-) Drivers kick panel. Gray 39 E Lock Green 25 (-) Drivers kick panel. Gray 39 E Unlock Yellow 39 (-) Drivers kick panel. Gray 39 E Trunk Release White 5 (-) Drivers kick panel. Gray 40 E EMS COM Blue/Black 15 Data Passenger kick panel, EM01 (Conn. 2*, Connection Type B**) Gray 39 F 15 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Hyundai Genesis Coupe 2010-2012 12V White 5 (+) Ignition switch. White 6 A Accessory Orange 3 (+) Ignition switch. White 6 A Ignition Blue 6 (+) Ignition switch. White 6 A Starter Pink 1 (+) Ignition switch. White 6 A Parking Lights White 1 (-) Headlight switch. White 13 F C-CAN High Red 6 Data OBDII. Black 16 B C-CAN Low Blue 14 Data OBDII. Black 16 B Brake Red/Orange 2 (+) Drivers kick panel. White 22 E Drivers Door Orange 34 (-) Drivers kick panel. Blue 39 E Lock Pink 36 (-) Drivers kick panel. Blue 39 E Unlock Orange 39 (-) Drivers kick panel. Blue 39 E Trunk Release Yellow 1 (-) Drivers kick panel. Blue 39 E EMS COM Yellow 24 Data Passenger kick panel, EM01 (Conn. 1*, Connection Type A**) Blue 39 F Hyundai Sonata 2008-2010 Brake Green 1 (+) Brake pedal switch. White 4 G 12V Pink 5 (+) Ignition switch. White 6 A Accessory Orange 3 (+) Ignition switch. White 6 A Ignition Blue 6 (+) Ignition switch. White 6 A Starter Green 1 (+) Ignition switch. White 6 A Drivers Door White 11 (-) Dash fuse box. White 12 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B Parking Lights Pink 14 (-) Headlight switch. White 18 F Unlock Yellow/Black 3 (-) Drivers kick panel. Red 20 E Trunk Release Yellow 1 (-) Drivers kick panel. Red 20 E EMS COM Green 23 Data Driver kick panel, EM21 (Conn. 3*, Connection Type B**) White 33 G Lock Pink/Black 2 (-) Drivers kick panel. Blue 39 E Kia Magentis 2009-2010 Brake Green 1 (+) Brake pedal switch. White 4 G 12V Pink 5 (+) Ignition switch. White 6 A Accessory Black 3 (+) Ignition switch. White 6 A Ignition Green 6 (+) Ignition switch. White 6 A Starter Green 1 (+) Ignition switch. White 6 A Drivers Door White 11 (-) Dash fuse box. White 12 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Black 14 Data OBDII. Black 16 B Parking Lights Pink 14 (-) Headlight switch. White 18 F Trunk Release White 16 (-) Drivers kick panel. Brown 18 E Lock Pink/Black 2 (-) Drivers kick panel. Red 20 E Unlock Yellow/Black 3 (-) Drivers kick panel. Red 20 E EMS COM Yellow/Orange 21 Data Driver kick panel, EM31 (Conn. 3*, Connection Type A**) White 33 G 16 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Kia Optima 2008-2010 Brake Green 1 (+) Brake pedal switch. White 4 G 12V Pink 5 (+) Ignition switch. White 6 A Accessory Black 3 (+) Ignition switch. White 6 A Ignition Green 6 (+) Ignition switch. White 6 A Starter Green 1 (+) Ignition switch. White 6 A Drivers Door White 11 (-) Dash fuse box. White 12 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Black 14 Data OBDII. Black 16 B Parking Lights Pink 14 (-) Headlight switch. White 18 F Trunk Release White 16 (-) Drivers kick panel. Brown 18 E Lock Pink/Black 2 (-) Drivers kick panel. Red 20 E Unlock Yellow/Black 3 (-) Drivers kick panel. Red 20 E EMS COM Yellow/Orange 21 Data Driver kick panel, EM31 (Conn. 3*, Connection Type A**) White 33 G Kia Rio 2008-2011 12V Pink 5 (+) Ignition switch. White 6 A Accessory Orange 3 (+) Ignition switch. White 6 A Ignition Pink 6 (+) Ignition switch. White 6 A Starter White 1 (+) Ignition switch. White 6 A C-CAN High Red 6 Data OBDII. Black 16 B C-CAN Low Blue 14 Data OBDII. Black 16 B Lock Blue 6 (-) Dash fuse box. White 16 C Unlock Yellow/Black 16 (-) Dash fuse box. White 16 C Brake Red/Orange 2 (+) Dash fuse box. Gray 18 C Parking Lights "Pink/Black (without BCM) Red (with 14 (-) Headlight switch. Blue 20 F BCM)" EMS COM Blue/Black 15 Data Right of Junction Box, EM01 (Conn. 2*, Connection Type A**) Gray 39 F Drivers Door Green 2 (-) Drivers kick panel. Green 42 E Kia Sportage (4-cyl) 2008-2010 Brake Red 1 (+) Brake pedal switch. White 4 G 12V White 5 (+) Ignition switch. Black 6 A Accessory Orange 3 (+) Ignition switch. Black 6 A Ignition Blue 6 (+) Ignition switch. Black 6 A Starter Green 1 (+) Ignition switch. Black 6 A C-CAN High Orange 6 Data OBDII. Black 16 B C-CAN Low Green 14 Data OBDII. Black 16 B Drivers Door Orange 8 (-) Drivers kick panel. Blue 16 E Lock Green 6 (-) Drivers kick panel. Blue 16 E Unlock Blue 7 (-) Drivers kick panel. Blue 16 E Parking Lights Brown 14 (-) Headlight switch. White 18 F EMS COM Blue/Black 14 Data Passenger kick panel, MC01 (Conn. 6*, Connection Type B**) Brown 23 F 17 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Kia Sportage (V6) 2008-2010 Brake Red 1 (+) Brake pedal switch. White 4 G 12V White 5 (+) Ignition switch. Black 6 A Accessory Orange 3 (+) Ignition switch. Black 6 A Ignition Blue 6 (+) Ignition switch. Black 6 A Starter Green 1 (+) Ignition switch. Black 6 A C-CAN High Orange 6 Data OBDII. Black 16 B C-CAN Low Green 14 Data OBDII. Black 16 B Drivers Door Orange 8 (-) Drivers kick panel. Blue 16 E Lock Green 6 (-) Drivers kick panel. Blue 16 E Unlock Blue 7 (-) Drivers kick panel. Blue 16 E Parking Lights Brown 14 (-) Headlight switch. White 18 F EMS COM Brown/Orange 7 Data Passenger kick panel, MC11 (Conn. 7*, Connection Type B**) Yellow 24 F * See below for a visual representation of each connector. ** See EMS COM Connection Types on Installation Wiring Diagram. EMS COM connectors 1 - EM01, Black or Blue 39-pin conn. 2 - EM01, Gray 39-pin conn. 3 - EM31 or EM21, White 33-pin conn. 15 24 15 23 21 4 - MC21, Green 18-pin conn. 5 - EM11, Black 46-pin conn. 6 - MC01, Brown 23-pin conn. 18 15 14 7 - MC11, Yellow 24-pin conn. 7 18 Directed Digital Solutions HKHT1

Type 3 with T-Harness (THHYC3) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires Ignition Switch EMS COM connections only needed if vehicle has transponder/immobilizer. EMS COM Data (veh. side): Orange/Black EMS COM Data (veh. side): Yellow EMS COM Data (conn. side): Yellow/Black EMS COM Data (conn. side): Orange/Yellow Remote Start Safety Override Switch (-) Lock Output: Dk. Green (-) Unlock Output: Dk. Blue Refer to the Vehicle wiring reference chart section for corresponding connector, pin and wire color of your vehicle. (-) RAP Off Output: White/Violet (-) Parking Light Output: Green/Balck (-) Trunk Release Output: Red/White 16-pin Black 2-pin Black THHYC3 (Optional T-Harness) The Remote Start Safety Override Switch MUST be in the ON position. OBDII - Diagnostic 16-pin Conn. Hood Pin (-) Hood Input: Gray: 3 Siren (+) Siren Output: Brown: 17 12-pin White Diagnostic OBDII 19 Directed Digital Solutions HKHT1

Type 3 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires C-CAN wires MUST be connected for proper operation. EMS COM connections only needed if vehicle has transponder/immobilizer. Diagnostic Conn. OBDII (wire side view) C-CAN High: pin 6 1 9 8 16 EMS COM Data (conn. side): Yellow/Black: 2 C-CAN Low: pin 14 EMS COM Data (veh. side): Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (-) Parking Light Output: Green/Black: 10 (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) 12V Input: Red (+) Accessory Output: Orange (+) 12V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink 8 thick-gauge wires MC501 4 White 7 White Hood Pin (-) RAP Off Output: White/Violet: 11 (-) Hood Input: Gray: 3 (-) Unlock Output: Dark Blue: 7 11: Orange/Yellow: EMS COM Data (conn. side) 10: Red: (+) 12V (-) Trunk Release Output: Red/White: 9 9: Black: (-) Ground (-) Lock Output: Dark Green: 15 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 6: Yellow: EMS COM Data (veh. side) (+) Siren Output: Brown: 17 Ignition, Accessory, Starter & (+) 12V wires at ignition switch, 6-pin connector Siren Refer to the Vehicle wiring reference chart. Refer to the Vehicle wiring reference chart. 20 Directed Digital Solutions HKHT1

Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information. Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Hyundai Accent 2012-2017 12V Green 1 (+) Ignition switch. Black 6 A Accessory Orange 2 (+) Ignition switch. Black 6 A Ignition Pink 4 (+) Ignition switch. Black 6 A Starter White 3 (+) Ignition switch. Black 6 A Parking Lights Pink/Black or Orange 7 (-) Headlight switch. White 14 C C-CAN High Green 6 Data OBDII. Black 16 B C-CAN Low Orange 14 Data OBDII. Black 16 B EMS COM Blue/Orange 11 Data Left of Junction Box, EM01 (Conn. 1*, Connection Type B**). Black 21 G Lock Brown (w/bcm) 15 (-) Drivers kick panel. (w/o BCM: add actuator in driver door). White 39 E Unlock Gray (w/bcm) 13 (-) Drivers kick panel. (w/o BCM: add actuator in driver door). White 39 E Drivers Door Brown/Orange 2 (-) Drivers kick panel. White 39 E Hyundai Elantra Touring 2009-2012 12V Orange 5 (+) Ignition switch. White 6 A Accessory Pink 3 (+) Ignition switch. White 6 A Ignition Blue 6 (+) Ignition switch. White 6 A Starter White 1 (+) Ignition switch. White 6 A Parking Lights Blue 8 (-) Headlight switch. White 14 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Yellow 14 Data OBDII. Black 16 B Drivers Door Red 36 (-) Drivers kick panel. Gray 39 E EMS COM Blue/Black 15 Data Passenger kick panel, EM11 (Conn. 2*, Connection Type B**). Gray 39 F Lock Green 25 (-) Drivers kick panel. Gray 39 E Unlock Yellow 39 (-) Drivers kick panel. Gray 39 E Trunk Release White 5 (-) Drivers kick panel. Gray 39 E 21 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Hyundai Santa Fe 2008-2012 12V Red 5 (+) Ignition switch. Black 6 A Accessory Red or Blue 3 (+) Ignition switch. Black 6 A Ignition Orange 6 (+) Ignition switch. Black 6 A Starter Green 1 (+) Ignition switch. Black 6 A C-CAN High Red/Black or Blue 6 Data OBDII. Black 16 B C-CAN Low Red or Orange 14 Data OBDII. Black 16 B Parking Lights Blue/Orange 14 (-) Headlight switch. White 18 C EMS COM White/Orange or White or Red 19 Data Passenger kick panel, MC211 (Conn. 3*, Connection Type A**). Blue 24 F Lock Blue/Black 18 (-) Drivers kick panel. Brown 24 E Unlock Gray/Black 19 (-) Drivers kick panel. Brown 24 E Drivers Door Green/Orange N/A (-) Drivers kick panel harness to rear. N/A N/A E Kia Rondo 2008-2012 12V Red or Pink 5 (+) Ignition switch. Black 6 A Accessory White or Pink 3 (+) Ignition switch. Black 6 A Ignition White/Blue or Blue 6 (+) Ignition switch. Black 6 A Starter Black/Yellow or Green 1 (+) Ignition switch. Black 6 A C-CAN High Red 6 Data OBDII. Black 16 B C-CAN Low Blue 14 Data OBDII. Black 16 B Trunk Release Blue/Orange 18 (-) BCM above brake pedal. White 22 G Drivers Door Red 36 (-) BCM above brake pedal. White 22 G Parking Lights Yellow 10 (-) BCM above brake pedal. White 26 G Lock White 8 (-) Drivers kick panel. Gray 39 E Unlock White/Black 9 (-) Drivers kick panel. Gray 39 E EMS COM Brown 18 Data Driver kick panel, EM11 (Conn. 4*, Connection Type A**). Blue 42 G * See below for a visual representation of each connector. **See EMS COM Connection Types on Installation Wiring Diagram. EMS COM connector 11 15 19 18 22 Directed Digital Solutions HKHT1

Type 4 with T-Harness (THHYC3) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires Ignition Switch EMS COM connections only needed if vehicle has transponder/immobilizer. EMS COM Data (veh. side): Orange/Black EMS COM Data (veh. side): Yellow EMS COM Data (conn. side): Yellow/Black EMS COM Data (conn. side): Orange/Yellow Remote Start Safety Override Switch (-) Lock Output: Dk. Green (-) Unlock Output: Dk. Blue Refer to the Vehicle wiring reference chart section for corresponding connector, pin and wire color of your vehicle. (-) RAP Off Output: White/Violet (-) Parking Light Output: Green/Balck (-) Trunk Release Output: Red/White 16-pin Black 2-pin Black THHYC3 (Optional T-Harness) The Remote Start Safety Override Switch MUST be in the ON position. OBDII - Diagnostic 16-pin Conn. Hood Pin (-) Hood Input: Gray: 3 Siren (+) Siren Output: Brown: 17 12-pin White Diagnostic OBDII 23 Directed Digital Solutions HKHT1

Type 4 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires C-CAN wires MUST be connected for proper operation. EMS COM connections only needed if vehicle has transponder/immobilizer. Diagnostic Conn. OBDII (wire side view) C-CAN High: pin 6 1 9 8 16 EMS COM Data (conn. side): Yellow/Black: 2 C-CAN Low: pin 14 (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) 12V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink (+) 12V Input: Red (+) Accessory Output: Orange 8 thick-gauge wires MC501 4 White 7 White Hood Pin EMS COM Data (veh. side): Orange/Black: 3 HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 (-) Parking Light Output: Green/Black: 10 (-) RAP Off Output: White/Violet: 11 (-) Hood Input: Gray: 3 (-) Unlock Output: Dark Blue: 7 11: Orange/Yellow: EMS COM Data (conn. side) 10: Red: (+) 12V (-) Trunk Release Output: Red/White: 9 9: Black: (-) Ground (-) Lock Output: Dark Green: 15 Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 6: Yellow: EMS COM Data (veh. side) (+) Siren Output: Brown: 17 Ignition, Accessory, Starter & (+) 12V wires at ignition switch, 6-pin connector (+) Accessory Interr. (conn. side) 87 87a 86 30 85 Siren Refer to the Vehicle wiring reference chart. (+) Accessory Interr. (veh. side) Refer to the Vehicle wiring reference chart. 24 Directed Digital Solutions HKHT1

Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information. Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Kia Forte 2010-2013 12V Black 5 (+) Ignition switch. Black 6 A Accessory Orange 3 (+) Ignition switch. Black 6 A Ignition Blue 6 (+) Ignition switch. Black 6 A Starter White 1 (+) Ignition switch. Black 6 A C-CAN High Black 6 Data OBDII. Black 16 B C-CAN Low White 14 Data OBDII. Black 16 B Parking Lights Blue/Orange 14 (-) Headlight switch. White 18 C Lock Blue/Black 18 (-) Drivers kick panel. Brown 24 E Unlock Green/Orange 19 (-) Drivers kick panel. Brown 24 E EMS COM Blue/Black 15 Data Passenger kick panel, MC12 (Conn. 2*, Connection Type B**) Gray 39 F Drivers Door Green/Orange N/A (-) Drivers kick panel. N/A N/A E Kia Forte5 2011-2013 12V Black 5 (+) Ignition switch. Black 6 A Accessory Orange 3 (+) Ignition switch. Black 6 A Ignition Blue 6 (+) Ignition switch. Black 6 A Starter White 1 (+) Ignition switch. Black 6 A Parking Lights Orange 1 (-) Headlight switch. White 13 C C-CAN High Black 6 Data OBDII. Black 16 B C-CAN Low White 14 Data OBDII. Black 16 B Trunk Release Blue/Black 2 (-) Rear of dash fuse box. White 18 C EMS COM Blue/Black 15 Data Passenger kick panel, MC12 (Conn. 2*, Connection Type B**) Gray 39 F Drivers Door Red 36 (-) Drivers kick panel. Gray 39 E Lock Blue/Black 18 (-) Drivers kick panel. Gray 39 E Unlock Green/Orange 19 (-) Drivers kick panel. Gray 39 E 25 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Kia Soul 2010-2013 12V White 5 (+) Ignition switch. Black 6 A Accessory White 3 (+) Ignition switch. Black 6 A Ignition Pink 6 (+) Ignition switch. Black 6 A Starter Blue 1 (+) Ignition switch. Black 6 A Parking Lights Pink 1 (-) Headlight switch. White 13 F C-CAN High Red 6 Data OBDII. Black 16 B C-CAN Low Blue 14 Data OBDII. Black 16 B Trunk Release Pink 10 (-) Passenger kick panel. White 26 D Drivers Door Green 9 (-) Passenger kick panel. White 26 D EMS COM Blue/Black 110 Data Above driver kick panel, EM11 (Conn. 5* Connection Type B**). Blue 39 G Lock Brown N/A (-) Drivers kick panel harness to rear. N/A N/A E Unlock Green N/A (-) Drivers kick panel harness to rear. N/A N/A E * See below for a visual representation of each connector. **See EMS COM Connection Types on Installation Wiring Diagram. EMS COM connector All adapters are displayed from the wire side (unless specified otherwise). 1 - MC12, Gray 39-pin conn. 2 - EM11, Blue 39-pin conn. 15 10 26 Directed Digital Solutions HKHT1

Type 5 with T-Harness (THHYC3) Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires B-CAN Wires See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. FT CAN Low: Orange/Brown FT CAN High: Orange/Green Ignition Switch EMS COM connections only needed if vehicle has transponder/immobilizer. EMS COM Data (veh. side): Orange/Black EMS COM Data (veh. side): Yellow EMS COM Data (conn. side): Yellow/Black EMS COM Data (conn. side): Orange/Yellow Remote Start Safety Override Switch (-) Lock Output: Dk. Green (-) Unlock Output: Dk. Blue Refer to the Vehicle wiring reference chart section for corresponding connector, pin and wire color of your vehicle. (-) RAP Off Output: White/Violet (-) Parking Light Output: Green/Balck (-) Trunk Release Output: Red/White (+) Brake Input: Brown/White 16-pin Black 2-pin Black THHYC3 (Optional T-Harness) The Remote Start Safety Override Switch MUST be in the ON position. OBDII - Diagnostic 16-pin Conn. Hood Pin (-) Hood Input: Gray: 3 Siren (+) Siren Output: Brown: 17 12-pin White Diagnostic OBDII 27 Directed Digital Solutions HKHT1

Type 5 Refer to "Pre-installation and application warnings" on page 4 for important information, such as the description of special notes referenced in the diagram ( ). EMS COM Connection Type See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. C-CAN wires MUST be connected for proper operation. Connection Type A Yellow + Yellow/Black wires Orange/Black + Orange/Yellow wires Connection Type B Orange/Black + Orange/Yellow wires Yellow + Yellow/Black wires Diagnostic Conn. OBDII C-CAN High: pin 6 1 9 8 16 EMS COM connections only needed if vehicle has transponder/immobilizer. C-CAN Low: pin 14 EMS COM Data (conn. side): Yellow/Black: 2 EMS COM Data (veh. side): Orange/Black: 3 B-CAN Wires See the Vehicle wiring reference charts for the connector, pin and wire color in your vehicle. (+) Starter Output (to starter): Violet Starter Input (from key switch): Green (+) 12V Input: Red (+) Accessory Output: Orange (+) 12V Input: Red (+) Ignition Output (also input to Yellow wire in ribbon cable): Pink 8 thick-gauge wires MC501 4 White 7 White HS CAN Low: Tan: 4 HS CAN High: Tan/Black: 5 FT CAN High: Orange/Green: 7 FT CAN Low: Orange/Brown: 8 (-) Parking Light Output: Green/Black: 10 (-) RAP Off Output: White/Violet: 11 Hood Pin (-) Hood Input: Gray: 3 (-) Unlock Output: Dk. Blue: 7 (-) Trunk Release Output: Red/White: 9 (-) Lock Output: Dk. Green: 15 (+) Brake Input: Brown/White: 16 (+) Siren Output: Brown: 17 10: Red: (+) 12V (+) 12V 9: Black: (-) Ground Remote Start Safety Override Switch The Remote Start Safety Override Switch MUST be in the ON position. 11: Orange/Yellow: EMS COM Data (conn. side) 6: Yellow: EMS COM Data (veh. side) Ignition, Accessory, Starter & (+) 12V wires at ignition switch, 6-pin connector Siren Refer to the Vehicle wiring reference chart. Refer to the Vehicle wiring reference charts for wire and connector details related to the standard connections in the vehicle. 28 Directed Digital Solutions HKHT1

Vehicle wiring reference chart This section provides vehicle wiring information to guide you through the various stages of your installation. Refer to www.directechs.com for additional information. All adapters are displayed from the wire side (unless specified otherwise). Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Kia Sorento 2011-2013 12V Red 1 (+) Ignition switch. White 6 A Accessory Blue 2 (+) Ignition switch. White 6 A Ignition Orange 4 (+) Ignition switch. White 6 A Starter Green 3 (+) Ignition switch. White 6 A Parking Lights Blue 2 (-) Headlight switch. White 13 C C-CAN High Blue 6 Data OBDII. Black 16 B C-CAN Low Red 14 Data OBDII. Black 16 C B-CAN High White or Blue 5 Data Rear of dash fuse box. White 16 D B-CAN Low Red 6 Data Rear of dash fuse box. White 16 D EMS COM Blue or Blue/Orange 18 Data Passenger kick panel, MC21 (Conn. 4*, Connection Type B**). Green 18 E Lock Blue/Black 4 (-) Dash fuse box. White 26 F Unlock Gray/Black 24 (-) Dash fuse box. White 26 F Hatch Release Yellow/Black 11 (-) Dash fuse box. White 26 F Brake Yellow or Green/ Black 1 (+) Brake pedal switch. White 4 J Drivers Door Green/Orange 10 (-) Dash fuse box. White 26 F 29 Directed Digital Solutions HKHT1

Wire Information Information Function Color Pin Polarity Location Color Pins Ref. Kia Sorento 2014-2015 12V Red 1 (+) Ignition switch. White 6 A Accessory Blue 2 (+) Ignition switch. White 6 A Ignition Orange 4 (+) Ignition switch. White 6 A Starter Green 3 (+) Ignition switch. White 6 A Parking Lights Blue 2 (-) Headlight switch. White 13 C C-CAN High White 6 Data OBDII. Black 16 B C-CAN Low Red 14 Data OBDII. Black 16 B B-CAN High Black 33 Data Driver kick panel. White 48 G B-CAN Low White 42 Data Driver kick panel. White 48 G EMS COM Blue/Orange 15 Data Driver kick panel, EM11 (Conn. 5*, Connection Type B**). White 46 H Lock Green 4 (-) Dash fuse box. White 26 F Unlock Brown/Black 5 (-) Dash fuse box. White 26 F Power Liftgate Gray/Black 5 (-) Overhead console. White 6 I Brake Yellow 4 (+) Driver kick panel, EM11 (Conn. 5*, Connection Type B**). White 46 H Drivers Door Red/Black 6 (-) Dash fuse box. White 26 F *See below for a visual representation of each connector. **See EMS COM Connection Types on Installation Wiring Diagram. images All adapters are displayed from the wire side (unless specified otherwise) 1 - MC21, Green 18-pin conn. 2 - EM11, White 46-pin conn. 18 15 30 Directed Digital Solutions HKHT1