RoHS Pb Dimensions and construction: (mm) Tube: End-cap: Solder: Adhesive: Marking: Lead-free glass Nickel plated brass 62 ma 1.25 A Over 1.25 A 3 A Epoxy resin 62 ma less than 1 A 1 A 3 A Sn-0.7Cu Sn-3.0Ag-0.5Cu SOC MQ4 SOC MQ4 250V [rated ] 250V [rated ] Electrical characteristics: voltage Certification (I N ) AC 250 V 62 ma 3 A 100 A breaking PF 0.7 0.8 Temperature rise 70 K or less at 1.1 I N Current carrying capacity Not less than 15 min after temperature stabilization at 1.1 I N * 1 * 2 temperature is obtained on each Until constant part at 1.1 I N Overload operation Within 60 min at 1.35 I N Within 2 min at 2.0 I N * 1 Fuses with rated s below 1 A are not covered under the Electrical Appliance and Material Safety Law. * 2 140 K or less at the center of the insulating tube and 60 K or less at the contact while the fuse is carrying 1.1 I N. Typical cold resistance: Agency approval information: Cold resistance Cold resistance Cold resistance 100 ma 9.0 Ω 400 ma 1.1 Ω 1.6 A 78 mω 125 ma 6.5 Ω 500 ma 685 mω 2 A 57 mω 160 ma 4.8 Ω 630 ma 410 mω 2.5 A 41 mω 200 ma 2.5 Ω 800 ma 310 mω 3 A 33 mω 250 ma 2.4 Ω 1 A 200 mω 315 ma 1.6 Ω 1.25 A 170 mω Note: These values are for reference only and are not intended to infer any guaranteed values. UL198G Listed Agency/Standard CSA C22.2 No.59.2 Certified Conformity Certificate Specified in Clause 9 of the Electrical Appliance and Material Safety Law (EAMSL) of Japan has been issued by JET (Japan Electrical Safety & Environment Technology Laboratories) Ratings covered 62 ma 3 A 1 A 3 A
Pre-arcing I-t characteristic: These I-t curve plots are of the average values of the measurements obtained under the conditions specified by our company. These data are for reference only and are not intended to infer any guaranteed values. Characteristics of the fuse may vary depending on the usage conditions. Always test the fuse under the actual circuit conditions. Control No.: 050401 10A Current 1A 0.1A 400 ma 315 ma 250 ma 200 ma 160 ma 125 ma 100 ma 1ms 10ms 100ms 1s 10s Pre-arcing time Control No.: 160711 100A Current 10A 1A 3 A 2.5 AA 2 A 1.6 AA 1.25 AA 1 A 800 ma 630 ma 500 ma 10ms 100ms 1s 10s 100s Pre-arcing time
Pre-arcing I 2 t-t characteristic: These I 2 t-t curve plots are of the average values of the measurements obtained under the conditions specified by our company. These data are for reference only and are not intended to infer any guaranteed values. Characteristics of the fuse may vary depending on the usage conditions. Always test the fuse under the actual circuit conditions. Control No.: 050401 1A 2 2 s I 2 t 0.1A 2 2 s 400 ma 315 ma 250 ma 200 ma 160 ma 125 ma 100 ma 0.01A 2 2 s 1E-3A 0.001A 2 2 s 1ms 10ms 100ms 1s Time Control No.: 160711 100A 2 2 s I 2 t 10A 2 2 s 1A 2 2 s 3 A 2.5 A 2 A 1.6 A 1.25 A 1 A 800 ma 630 ma 500 ma 0.1A 2 2 s 1ms 10ms 100ms 1s Time
Influence of ambient temperature-the re-rating of the rated : This chart is a plot of the measurements obtained at the ambient temperatures of 40 C, 25 C, and 85 C under conditions specified by our company. The conditions of your actual application are not considered in this chart. These data are for reference purposes only and are not intended to infer any guaranteed values. Fuse characteristics may vary depending on the usage conditions. Always test the fuse under the actual circuit conditions. 120 Control No.: 170401 Factor of rated (%) 110 100 90 80 100 ma-250 ma 250 ma ma 315 ma-800 ma 800 ma ma 1 A-1.6 A 1.6 A 2 A-3 A 3 A 70-60 -40-20 0 20 40 60 80 100 Ambient temperature ( C)
Usage conditions: * Ambient temperature: 40 C +85 C * Ambient humidity: 85% RH or less Note: Current carrying capacity of the fuse may vary depending on the ambient temperature. Storage conditions and storage period: Products packaged as delivered can be stored for one year from our shipment under the following conditions. * Ambient temperature: 30 C +40 C (no condensation) * Ambient humidity: 85% RH or less * Ambient atmosphere: Not exposed to corrosive gas or sea breeze No visible dust Not exposed to direct sunlight * Load: No application of load that may cause deformation or degradation of the product. Environmental information: This product conforms to the EU RoHS Directive 2011/65/EU. The six hazardous substances (lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls [PBB], and polybrominated diphenyl ethers [PBDE]) specified in the EU RoHS Directive are not used intentionally in this product. However, when lead is used in applications exempted from the requirements of the Directive, this will be indicated in the Dimensions and Construction section of the corresponding product specification. Packaging: 1. 1,000 fuses are packed into a colorless transparent polyethylene bag. 2. An identification label is attached to each bag. 3. A bag of 1,000 fuses is packed into the cardboard case shown in the figure below. If the number of fuses is less than the fixed number, the fuses are still packed into the cardboard case in the same manner. 4. The following are indicated on the surface of the cardboard case: * Your part number (by request) * Quantity of fuses * Packaged date * Country of origin * Manufacturer * Production facilities * Indications required by the applicable standards (mm) Lot number: The lot number indicates the following: Example: 17012371 170123: Date manufactured 71: Process code
Ordering specifications: SOC product name: MQ4 [rated ] N1 Contact information: SOC is a global ISO9001 and IATF16949 registered company headquartered in Japan with subsidiaries in Asia, Europe, and North America. SOC Corporation Marketing Division: 3-16-17, Takanawa, Minato-ku, Tokyo 108-0074, Japan TEL +81-3-5420-1011 FAX +81-3-5420-6699 http://www.socfuse.com/contact/index.html SOC America Inc.: 3505 Veterans Memorial Highway, Suite K-1, Ronkonkoma, NY 11779, USA TEL +1-631-472-6666 FAX +1-631-472-6777 http://www.socamericainc.com info@socamericainc.com SOC Asia Pte. Ltd.: 15 Jalan Kilang Barat, #07-02 Frontech Centre, Singapore 159357 TEL +65-6376-4115 http://www.socfuse.com/contact/index.html socjp@pacific.net.sg SOC Europe B.V.: Databankweg 1, 3821 AL Amersfoort, the Netherlands TEL +31-33-450-4000 http://www.soceurope.nl info@soceurope.nl
Safety Precautions for Fuse Selection and Use: WARNING Read and follow these precautions before selecting and using fuses and protectors (hereafter fuses ). Failure to properly select, install, and use fuses can result in not only property damage, but also serious injury or death. Use fuses within their specification requirements. Exposing fuses to conditions that exceed or are outside specifications can lead to, for example, non-operation, nuisance operations, disconnection of the fuse-element, or explosions, and may cause injuries and/or property damage. Please note that breaking conditions for s below the minimum breaking and which exceed the rated breaking are outside the range of the specification conditions. Please use this product after ensuring that the actual breaking conditions in the application are not included in this range. Fuse performance can vary greatly due to the actual conditions fuses are operated under (ambient temperature, pulse s, heat shock, mechanical stress, etc.). Please consider all conditions a fuse will be exposed to when making a selection. Depending on the conditions, non-operation, nuisance operations, disconnection of the fuse-element, explosions, or other accidents may occur, and these may cause injuries and/or property damage. The breaking ability of a fuse will differ between AC and DC circuits. Use fuses with AC voltage ratings in AC circuits and fuses with DC voltage ratings in DC circuits. When using fuses with both AC and DC voltage ratings, attention should be given to any differences in breaking ability. A fuse s breaking ability indicates the fuse s ability in an AC or DC circuit. For example, if a fuse with an AC voltage rating is used in a DC circuit, the fuse s breaking ability will decrease, and injuries and/or property damage may occur. Check if the circuit voltage is large enough for the fuse s operation. When the circuit voltage is too small, the decrease in caused by an increase in the fuse s resistance may prevent the fuse from operating even for abnormal s. Do not use fuses in environments with high humidity or corrosive or flammable gases. Doing so may result in nuisance operations, disconnection of the fuse-element, or an explosion. Do not use ultrasonic waves to clean fuses. Ultrasonic cleaning may cause disconnection of the fuse-element. Do not form a fuse s leads when the fuse is at a temperature of 40 C or greater. Doing so may result in disconnection of the fuse-element because of the applied stress. Do not apply coating or potting to any fuses except sealed fuses, such as the MCFA, or their equivalents, including the MCF3. Doing so may cause disconnection of the fuse-element or a change in the fuse s characteristics. Please be aware that even sealed fuses or the equivalent are not hermetically sealed, and therefore make sure to confirm no coating or potting material has penetrated the interior or any other location of the fuse before use. As coating or potting a fuse will changes its characteristics, make sure to confirm that a coated or potted fuse still satisfies all requirements under actual usage conditions. Avoid applying excessive force when inserting a fuse into a fuse holder. Doing so may result in the fuse cracking or in contact failure, and this may significantly reduce its ability to work properly or may shorten its life. When a fuse is used in equipment that directly affects human life or that requires a high degree of reliability, more closely examine and evaluate the fuse in actual circuit conditions than is necessary for use in other general electronic equipment. Do not touch fuses when they are carrying a. Doing so may result in electrocution or serious burns. Fuses obtained as samples should only be used for evaluation. Do not reuse fuses, but instead properly dispose of them. For final fuse selection, make sure to install the fuse in the actual application in order to confirm the selected fuse satisfies all requirements.