Illustrated Parts & Packing List 528 Gandrud Road, Owatonna, MN 55060 For a complete distributor & dealer list go to www.gandy.net 66GW27F Orbit-Air Applicator 120 Cu. Ft. Hopper w/ 27 (2 ) Openings, Fertilizer (F) Red Wheels With 15 GPM Hydraulic Fan Motor Hydraulic Raven Monitor Controlled Split Shaft, Three Clutch, for 2-inch I.D tubing 1... 6298-24... Mounting Base, Hopper Use: 16 Carriage Bolt (3/8 x 1) (C04-0375-040) 16 Whiz Flange Nut (3/8) (C01-0375-030) 2 Decal, Gandy Orbit-Air 66 series Large (N02-0001-081) 1 Decal, Important, Metering Wheel (N02-0062-040) 2 Decal, Caution (N02-0014-010) 2 Decal, Important Transport (N02-0062-044) 1 Decal, Caution Black on Yellow (N02-0062-050) 1... 6298-1... Hopper, 120 CU. FT. Use: 60 Pop Rivet (3/16 x 3/8) (C19-0187-030) 6 Window (5 x 10) (6299-24) 12 Rail, Large (6299-26) 12 Rail, Small (6299-27) 4... 62142-1... Brace Use: 8 Hex Bolt (3/8 x 1) (C03-0375-041) 8 Lock Washer (3/8) (C02-0375-010) 8 Wrought Washer (3/8) (C02-0375-030) 8 Whiz Flange Nut (3/8) (C01-0375-030) 4 U-Bolt (3/8) (644-2) 1... 6298-2... Hopper Roof, 120 CU. FT. Use: 36 HHTC (5/16 x 3/4) (C03-0312-033) 36 Whiz Flange Nut (5/16) (C01-0312-030) 1... 63862-2... Cover, 120 CU. FT. 2... M05-0000-004... Rubber Latch Use: 8 Pop Rivet (3/16 x 1/4) (C19-0187-000) 2... 62852-3... Inner Hinge (for Cover) Use: 2 Hex Bolt (3/8 x 3/4) (C03-0375-030) 4 Wrought Washer (3/8) (C02-0375-030) 4 Jam Nut, Nylon Lock (3/8) (C01-0375-062) 2... 6298-15... Outer Hinge (for Cover) Use: 2 Hex Bolt (3/8 x 1) (C03-0375-041) 4 Wrought Washer (3/8) (C02-0375-030) 4 Jam Nut, Nylon Lock (3/8) (C01-0375-062) 1... 6298-34... Cover Hinge Support Rod Use: 4 Whiz Flange Nut (5/8) (C01-0625-030) Page 1 of 20
3... 62852-21... Shaft (5/8 x 32-3/4) 6... 63861-7... Plastic Bearing (5/8 Bore) 12... 09074690-4... Flangette (For 63861-7 Bearing) Use: 12 Carriage Bolt (1/4 x 5/8) (C04-0250-020) 12 Whiz Flange Nut (1/4) (C01-0250-030) 3... 62851-42... Chain Sprocket, 21-Tooth, 5/8 Bore Use: 3 Cotter Pin (3/16 x 1-1/4) (C20-0187-030) 2... 62853-9... Sprocket, 24-Tooth (5/8 Bore x 1-3/8 Hub) Use: 2 Cotter Pin (3/16 x 1-1/4) (C20-0187-030) 1... 63862-10... Sprocket, 24-Tooth (5/8 Bore x 1-1/2 Hub) (used on center door) Use: 1 Cotter Pin (3/16 x 1-1/4) (C20-0187-030) 1... 6298-16... Shaft (1-inch x 32-1/4) 1... 6298-17... Shaft (1-inch x 74) 1... 6298-18... Coupling, Shaft (120 cu ft Hopper) Use: 1 Key (1/4 x 1/4 x 1-3/4) (2893-41) 4 Socket Set Screw (5/16 x 1/4) (C06-0312-010) 3... D05-1000-010... Bearing (1-inch) Use: 6 Hex Bolt (5/16 x 3/4) (C03-0312-030) 6 Lock Washer (5/16) (C02-0312-010) 6 Hex Nut (5/16) (C01-0312-010) 3... 62853-10... Chain Sprocket, 32-Tooth (One Bolted to Each Clutch) Use: 12 Hex Bolt (1/4 x 3/4) (C03-0250-030) 12 Whiz Flange Nut (1/4) (C02-0250-030) 1... 62853-12... Electric Clutch, w/ 35-Tooth Sprocket (Hydraulic Drive Side) Use: 1 Clutch Washer (62854-29) 1 SAE Washer (1-inch) (C02-1000-020) 1 Sprocket 35 Tooth (62853-12/10) (part of 62853-12) 1 Hex Bolt (5/16 x 5/8) (C03-0312-020) 1 Hex Bolt (3/8 x 1-3/4) (C03-0375-071) 1 Lock Washer (5/16) (C02-0312-010) 2 Whiz Flange Nut (3/8) (C01-0375-030) 2... L05-0010-001... Electric Clutch Use: 1 Clutch Washer (62854-29) 2 SAE Washer (1-inch) (C02-1000-020) 1 Hex Bolt (5/16 x 5/8) (C03-0312-020) 1 Hex Bolt (3/8 x 1-3/4) (C03-0375-071) 1 Hex Bolt (3/8 x 2-1/4) (C03-0375-091) 1 Lock Washer (5/16) (C02-0312-010) 4 Whiz Flange Nut (3/8) (C01-0375-030) 2... 6298-23... Spacer (1-1/4 x 7/8) (for Outside Clutches) 1... 2406251... Collar, Locking (for 1-inch Shaft) Use: 1 SQ Head Set Screw (3/8 x 5/8) (C05-0375-030) 1 SAE Washer (1-inch) (C02-1000-020) 1... 6298-32... Windshield, Clear Use: 13 Hex Bolt (1/4 x 1/2) (C03-0250-010) 13 Wrought Washer (5/16) (C02-0312-030) 13 Whiz Flange Nut (1/4) (C01-0250-030) Page 2 of 20
1... 6298-26... Air Chamber 120-150 Cu Ft, 9 Outlet (Center) Use: 2 Hex Bolt (3/8 x 3/4) (C03-0375-30) 2 Whiz Flange Nut (3/8) (C01-0375-030) 2 Whiz Flange Nut (1/2) (C01-0500-030) 1 U-Bolt (1/2) (6108430-3) 2... 6298-27... Air Chamber Extension 120-150 Cu Ft, 9 Outlet Use: 4 Hex Bolt (3/8 x 3/4) (C03-0375-030) 4 Whiz Flange Nut (3/8) (C01-0375-030) 8 FT.... M06-4000-000... Hose, 4-inch I.D. (Two Sections 4 FT Each) Use: 4 Hose Clamp (#64) (M11-0064-000) 6... M05-2000-000... Rubber Plug (2-inch) 4... 6298-19... Mounting Strap, Air Chamber Extension Use: 8 Hex Bolt (3/8 x 3/4) (C03-0375-030) 8 Whiz Flange Nut (3/8) (C01-0375-030) 27... M05-0829-310... Gasket Mixing Chamber, 2-inch 27... 638616-5... Mixing Chamber, 2 Inch (For 1-1/2 I.D. Tubing) Use: 54 Hex Head TC Screw (5/16 x 3/4) (C03-0312-032) 1... 5508242-33... Gasket, Potting Box 1... L10-0016-001... Potting Box Use: 2 Phillips Pan Head TC Screw (#8-32 x 1/2) (C07-0164-070) 1... 641-3... Sensor Wire Assembly Use: 2 Pan Head TC Screw (#8 x 1/2) (C07-0164-070) 1 Air Tag (66Air) 1 Cable Tie (3/16 x 8) (L04-0001-000) 2... M05-4000-000... Rubber Plug, 4-inch (Hopper Clean-Out) 1... 6299-17... Clean Out Chute, Hopper 5-inch Use: 1 Wing Nut (5/16) (C01-0312-020) 1 Wrought Washer (5/16) (C02-0312-030) 1 Decal, Caution Plug (N02-0062-051) 1... 6298-12... Angle Clamp, Tubing Use: 4 Bushing (3/4 x 15/32) (5808325) 4 Hex Bolt (3/8 x 1-1/4) (C03-0375-051) 4 Lock Washer (3/8) (C02-0375-010) 4 Wrought Washer (3/8) (C02-0375-030) 3... 6108515... Bar Clamp, Plastic Tube Use: 9 Hex Bolt (5/16 x 2-3/4) (C03-0312-110) 9 Lock Nut, Nylon (5/16) (C01-0312-040) 9 Wrought Washer (5/16) (C02-0312-030) 1... 6298-5... Platform (Bolted To Front of Hopper) Use: 6 Carriage Bolt (3/8 x 3/4) (C04-0375-030) 6 Whiz Flange Nut (3/8) (C01-0375-030) 1... 6298-6L... Support Bracket, Left (In Hopper) Use: 3 Carriage Bolt (3/8 x 3/4) (C04-0375-030) 3 Whiz Flange Nut (3/8) (C01-0375-030) 1... 6298-6R... Support Bracket, Right (In Hopper) Use: 3 Carriage Bolt (3/8 x 3/4) (C04-0375-030) 3 Whiz Flange Nut (3/8) (C01-0375-030) 2... 62137-9... Spacer (2 x 1) Page 3 of 20
1... 6298-20... Support Bracket, Left Middle (In Hopper) Use: 2 Hex Bolt (3/8 x 3) (C03-0375-121) 2 Wrought Washer (3/8) (C03-0375-030) 2 Whiz Flange Nut (3/8) (C01-0375-030) 1... 6298-21... Support Bracket, Right Middle (In Hopper) Use: 2 Hex Bolt (3/8 x 3) (C03-0375-121) 2 Wrought Washer (3/8) (C02-0375-030) 2 Whiz Flange Nut (3/8) (C01-0375-030) 1... 6298-4... Railing (Strapped to Hopper) Use: 3 Hex Bolt (3/8 x 1) (C03-0375-041) 3 Whiz Flange Nut (3/8) (C01-0375-030) 1... 638614-9... End Rail, Top (In Hopper) Use: 1 U-Bolt (1/4) (638614-7) 2 Whiz Flange Nut (1/4) (C01-0250-030) 1... 6298-22... End Rail, Bottom (In Hopper) Use: 1 Hex Bolt (5/16 x 3/4) (C03-0312-030) 1 U-Bolt (1/4) (638614-7) 2 Whiz Flange Nut (1/4) (C01-0250-030) 1 Whiz Flange Nut (5/16) (C01-0312-030) 1... 638614-6... Ladder (Banded to Platform) (All Hardware Inside Hopper) Use: 4 U-Bolt (1/4) (638614-7) 2 Mounting Strap (638614-5) 8 Whiz Flange Nut (1/4) (C01-0250-030) 2 Black Cap (1 I.D. x 2 ) (J02-1000-000) (in place on ladder) 4... 6298-3... Screens Sensors & Wire Extensions 3... L07-0117-484... Shaft Sensor Kit (Sensor Only Replacement Number L07-0115-964) 3... 629066-9... Mounting Bracket, Sensor 3... 661-14... Sensor Wire Extension (24-Inches Long) 1... 66SHAFT1... Shaft Tag 1 Use: 1 Cable Tie (3/16 x 8) (L04-0001-000) 1... 66SHAFT2... Shaft Tag 2 Use: 1 Cable Tie (3/16 x 8) (L04-0001-000) 1... 66SHAFT3... Shaft Tag 3 Use: 1 Cable Tie (3/16 x 8) (L04-0001-000) 1... 641-4... Wire Assembly, Clutch 30-Inch Long (For Center Clutch) 2... 641-5... Wire Assembly, Clutch 60-Inch Long (For Outside Clutches) 1... 66CLUTCH1... Clutch Tag 1 Use: 1 Cable Tie (3/16 x 8) (L04-0001-000) 1... 66CLUTCH2... Clutch Tag 2 Use: 1 Cable Tie (3/16 x 8) (L04-0001-000) 1... 66CLUTCH3... Clutch Tag 3 Use: 1 Cable Tie (3/16 x 8) (L04-0001-000) Page 4 of 20
Hydraulic Blower Components 1... 62167-1... Mount Blower (Crary Fan) Use: 2 Decal, Warning Rotating (N02-0055-010) 1 Decal, Important Hydraulic Motor (N02-0062-043) 2 Decal, Caution Black on Yellow (N02-0062-050) 1 Decal, Tag Important Caution (N04-0000-000) 4 Hex Bolt (3/8 x 1-1/2) (C03-0375-061) 4 Lock Washer (3/8) (C02-0375-010) 8 Wrought Washer (3/8) (C02-0375-030) 4 Hex Nut (3/8) (C01-0375-010) 1... L01-0033-000... Fan Assembly (Crary) Use: 1 Bushing (1-inch) (L01-0033-002) 4 Hex Bolt (1/2 x 1-1/2) (C03-0500-062) 4 Lock Washer (1/2) (C02-0500-010) 4 Hex Nut (1/2) (C01-0500-010) 1... 5408320-25... Key, Fan Shaft (1/4 x 1-inch) 1... 62167-3... Shaft (6-Inch) 1... 28122-49... Key, Coupler (3/16 x 1-inch) 1... K18-M024-000... Coupler (9/16 x 7/8) Replacement Parts...(K18-M024-003 Coupler Sleeve) (5508230-5 Key 1/8 x 1) (K18-M024-004 Coupler for 9/16 Shaft on Hyd Motor) (K18-M024-005 Coupler for 7/8 Shaft on End of Fan Shaft) 2... D05-1000-030... Bearing & Locking Collar (For 1-inch Shaft) 4... D10-1000-011... Flangette, Round (For D05-1000-030 Bearing) Use: 6 Carriage Bolt (5/16 x 1) (C04-0312-040) 6 Hex Nut (5/16) (C01-0312-010) 6 Lock Washer (5/16) (C02-0312-010) 1... K01-0045-002... Hydraulic Motor, 15 GPM Use: 2 Carriage Bolt (3/8 x 1-1/4) (C04-0375-051) 2 Washer, Motor Side, Stainless (62164-2) 2 Lock Nut, Nylon (3/8) (C01-0375-041) 1... 5508336-7... Guard, Blower Shaft Use: 2 Thumb Screw (5/16 x 3/4) (C09-0312-100) Hydraulic Hoses 1... K02-0375-024... Hydraulic Hose, 3/8 x 24 (Case Drain) 3... K02-0500-014... Hydraulic Hose, 1/2 x 14 (w/ O Ring Fitting on One End) 1... K02-0500-021... Hydraulic Hose, 1/2 x 21 1... K02-0500-050... Hydraulic Hose, 1/2 x 50 2... K02-0500-120... Hydraulic Hose, 1/2 x 120 1... K07-0500-010... Steel Pipe Tee (1/2 ) 2... K09-0500-000... 90 High Pressure SP Elbow (1/2 ) 1... K11-0500-028... Steel Pipe Nipple (1/2 x 1-13/16) 1... L04-0005-000... Cable Tie (5/16 x 15-1/4) 1... 62113... Hydraulic By-Pass Block Assembly w/check Valve Use: 1 Check Valve (K05-CV10-200) 1 Hydraulic By-Pass Block (6296-1) Page 5 of 20
Hydraulic Drive Components 1... 661-3... Motor Control Bracket Use: 2 Hex Bolt (5/16 x 3/4) (C03-0312-030) 2 Whiz Flange Nut (5/16) (C01-0312-030) 1... 661-1... Motor Mount Bracket Use: 1 U-Bolt (3/8) (644-2) 2 Whiz Flange Nut (3/8) (C01-0375-030) 1... L07-0063-189... Hydraulic Control Valve, 16-GPM 1... 648-1... Mounting Plate, Motor Use: 2 U-Bolt (3/8) (644-2) 4 Whiz Flange Nut (3/8) (C01-0375-030) 1... 648-2... Spacer Plate 1... 09073678-4... Motor Mount Plate Use: 4 Hex Bolt (1/4 x 1) (C03-0250-040) 4 Lock Washer (1/4) (C02-0250-010) 2 Carriage Bolt (3/8 x 1-1/4) (C04-0375-051) 2 Whiz Flange Nut (3/8) (C01-0375-030) 1... K01-1022-000... Hydraulic Motor A Series #130-108 1... 661-13... Regulator Block Use: 4 Socket Head Cap Screw (5/16 x 2) (C06-0312-130) 1... L08-SV10-230... Solenoid Valve Use: 2 Terminal, 14-16ga, Male #634005 (L03-0009-090) 1... 661-2... Sensor Bracket Use: 1 Carriage Bolt (1/4 x 5/8) (C04-0250-020) 1 Whiz Flange Nut (1/4) (C01-0250-030) 1... 661-11... Sprocket Sensor 1... 661-7... Sprocket, 13-Tooth (1 Inch Bore w/keyway) Use: 1 Key (1/4 x 1) (5408320-25) 1... 661-6... Bushing (1-1/8 x 7/8 I.D. x 1/2) 1... 661-4... Sprocket, 20-Tooth (7/8 Bore) Use: 2 Spring Pin (1/8 x 1-3/4) (C23-0125-200) 1... 661-5... Collar, Hydraulic Speed Comp Drive Use: 1 Hex Bolt (1/4 x 1-1/4) (C03-0250-051) 1 Lock Washer (1/4) (C02-0250-010) 2.58 FT... F02-0041-000... Roller Chain (#41) (62-Rollers) Use: 1 Connector Link #41 (F02-0041-001) Page 6 of 20
3... 63862-A... Metering Door Assembly, 9-outlet (Red Fertilizer Wheels) 3... 63861-17... Mounting Plate (9 Outlet, 2-inch Cup) Use: 6 J- Bolt (C19-0312-020) 6 Wrought Washer (5/16) (C02-0312-030) 6 Wing Nut (5/16) (C01-0312-020) 9.5 FT.... M05-0125-050... Rubber Strip w/ Adhesive 27... 63861-12S... Metering Cup (Stainless, 2-inch) Use: 30 Whiz Flange Nut (3/16) (C01-0187-030) 27... 63861-8S... Hole Closure (2-inch) Use: 27 Hex Bolt (5/16 x 1/2) (C03-0312-010) (Stainless) 27 Lock Washer (5/16) (C02-0312-010) 3... 62852-14... Hex Shaft (5/8 x 31-9/16) 6... 63861-7... Bearing, Plastic (5/8 Bore) 12... 09074690-4... Flangette (For 63861-7 Bearing) Use: 12 Hex Bolt (1/4 x 1/2) (C03-0250-013) (Stainless) 12 Lock Washer (1/4) (C02-0250-012) (Stainless) 54... M10-0001-070... Metering Wheels, Fertilizer, Red (1-inch Wide, 2 Per Cup) 3... 62854-41... Sprocket, 21-Tooth, 5/8 Bore Use: 1 Cotter Pin (3/16 x 1-1/4) (C20-0187-030) The Following Parts Are Shipped Inside Hopper: 1... 0197102-1... Manual Bracket Holder 2... L04-0005-000... Cable Tie (5/16 x 15-1/4) 1... M10-0005-004... Manual Holder 12... 63861-10S... Blank Plate, Metering Assembly 12... 638616-4... Blank Plate (to Close off Unused Openings on Air Chamber) 1... Bag Containing Parts for Installing Ladder 1... L07-0063-829... Console 1... L07-0115-456... Control Valve Adapter Cable 1... L07-0115-651... Grain Flow Cable 10, 22 Pin 1... L07-0115-652... Grain Flow Cable 12, 22 Pin 1... L07-0063-484... Wheel Speed Sensor 1... L07-0115-534... Shaft Sensor Extension 1... L07-0115-715... Cable, 3 Clutch, 3 Shaft 1... 638616-D... Air Pressure Gauge Carton Containing: 1... K17-P734-004... Air Pressure Gauge 4 Inch 1... 62851-46... Mounting Bracket, Air Pressure Gauge 1... 62851-47... Clamp Bracket (for Mounting Gauge on Lifting Loop) 2... K04-0250-0375... Adaptor, Plastic (1/4 MPT x 3/8 HB) 8 FT.... M06-0375-000... Tubing, 3/8 x 1/8 Wall 1... C03-0312-041... Hex Bolt (5/16 x 1 gr5) 1... C01-0312-030... Whiz Flange Nut (5/16) 2... C01-0250-030... Whiz Flange Nut (1/4) 1... 638614-7... U-Bolt (1/4) (for Mounting on Ladder or Railing) Continued on next page Page 7 of 20
1... 662-C... Run/Hold Switch Assembly 1... 62150-20... Run Hold Mount Use: 2 U-Bolt (1/4) (62150-24) 4 Whiz Flange Nut (1/4) (C01-0250-030) 3 Hole Plug (3/8) (J03-0375-000) 1... L05-0001-001... Switch, Snap Action, #3XG49-9 Use: 2 Slot RD HD Mach Screw (#6-32 x 1-1/4) (C08-0138-140) 2 Shake Proof Washer (#6) (C02-0138-040) 2 Hex Nut (#6-32) (C01-0138-010) 1... 6611-1... Run Hold Cable Assembly Use: 1 Strain Relief Bushing (J04-0500-000) 1... C16-0250-010... Eye Bolt (1/4 x 9/16 I.D. x 2-1/2) 1... E07-0585-3... Compression Spring 1... 62150-22... Bushing (3/8 x 18ga x.60) 1... C01-0250-101... Coupling Nut (1/4) 1... 62150-23... Stop Washer 1... C03-0250-110... Hex Bolt (1/4 x 2-3/4) 2... C01-0250-010... Hex Nut (1/4) 1... E00-0375-040... Spring 1.33 FT... F03-0025-000... Sash Chain, #25 (16-inches) 1... M11-0006-000... S Hook #63 1... 62150-21... Spring Bracket Page 8 of 20
Hopper Assembly Page 9 of 20
Drive Shaft Assembly Part numbers with a (*) behind them have grease fittings. See last page. Page 10 of 20
Metering Door Assembly Page 11 of 20
Air Chamber Assembly Page 12 of 20
Blower Assembly Page 13 of 20
Hydraulic Hose Connections Page 14 of 20
Wiring Connections Page 15 of 20
Hydraulic Drive Assembly Page 16 of 20
Shaft Sensor Hydraulic Drive Sensor Page 17 of 20
Run Hold Switch Page 18 of 20
Ladder Assembly: 1. Mount ladder (638614-6) to side of hopper as shown using the hardware provided. 2. Top bolt for mounting ladder is in place. Remove whiz nut and fasten top ladder mounting bracket here. Using a 3/8 x 3/4 hex bolt and whiz flange nut mount the bottom ladder mounting bracket to the platform as shown. Tighten bolts securely. 3. Attach ladder to railing using the two mounting straps (638614-5) and four u-bolts (638614-7) as shown. Secure in place using the 1/4 whiz flange nuts. Tighten hardware securely. Page 19 of 20
Manual Holder Bracket Mount manual holder to corner of hopper or convergent location on implement. Store Operator s manual, Packing List & Rate Chart of convergent access. Maintenance Check all bolts for tightness after first two hours of use; check periodically thereafter. Grease all fittings regularly. There are three grease fittings on this hopper. These must be greased before use and periodically during use. Grease Fitting Location: See page 10 for locations. One grease fitting on each 1-inch bearing (D05-1000-010) (three), located on the 1-inch drive shafts (6298-16 & 6298-17). Lucubrate chains as needed. Periodically clean intake screen on hydraulic driven blower. See Raven Operator s Manual for operating and wiring instructions. Drawings; 120HOPPER, 66GS120, 63862-A, 66GW27F-120, 6299-15C, 66-120-15GPM, 661-A, 66GS, Hopside-2, 0630159, 662-C, HOLD1 June 4, 2012 Revised From (10/19/10) Printed in the USA Page 20 of 20