THE Municipality of Hastings Highlands Request for Proposal for supply and delivery of one (1) current year TANDEM AXLE DIESEL TRUCK CAB AND CHASSIS COMPLETE WITH PLOW/SAND COMBINATION UNIT Notice to vendors: The below specifications are typical to that of current equipment in use by the Municipality of Hastings Highlands and any proposals shall meet or exceed these Specifications. Any discrepancy to this specification must be approved by the Corporation of the Municipality of Hastings Highlands prior to its acceptance. The lowest or any tender/quotation not necessarily accepted; The Municipality of Hastings Highlands reserves the right to cancel the Request for Proposal (RFP) at any point in the process without liability. Evaluation of RFP Package: The RFP Package will be checked for compliance to the RFP request and a compliant RFP will be evaluated as below, but not necessarily in that order: a. Vehicle specifications outlined; b. Qualifications and good references; c. Dealer authorized by manufacturer to sell, service and provide warranty; d. Service Availability; e. Delivery timelines; f. Training provided g. Price. 2
Delivery Date Time is of the essence. In order to determine the realistic timelines from date of award to delivery of vehicles, the selected Bidder will update the Municipality with progress reports on a regular basis. If required, an alternate delivery date will be mutually agreed upon. Snow plow specification: VCL Steel Rev Plows & Options * 36-12-45C, VCL Steel Reversible Plow, 12' 45 degree compression spring full trip moldboard, 10 ga, 36" high, 9' 8" clearing path @ 35. * 3/4 x 6 x 144" carbide cutting edge (3 pcs 3/4 x 6 x 48"), bull nose, * Qty (2) of Carbide moldboard shoe ( each ) * Qty (2) of 36" Plow marker whip, fluorescent orange * Rubber snow deflector 1/2"x12" includes mounting hardware * Standard Alkyd enamel finish w/ corrosion protection: Medium Gloss Black (moldboard and push frame) * Grade 70 Chain Upgrade (Plow Only) VCL500T Hydraulic Tilt Harness * painted VCL black, includes 1/2" tail plates to suit chassis, plow lift yolk and 4x10 plow lift Cylinder * Cut O.E.M. front bumper and re-install ends to chassis. * Quick attach pockets and pins * Standard Alkyd enamel black finish w/ corrosion protection : Medium Gloss Black * Front Drivers Side Foot Step attached to Tail Plate 3 VCL350 SCL Cable lift wing * tower Includes frame mount and Wing tower, 132 litre (35 US Gal) integrated back of cab hydraulic tank * Viking tube style frame cross member * Aeon rubber helper spring assembly. * Dual adjustable needle valves for rear wing rate control of UP/DN * Qty (3) of 4" LED spotlight w/ mounting bracket for rear wing * Standard Alkyd enamel black finish w/ corrosion protection: Medium Gloss Black
* spots for rear wing, spinner & BOC conv VCL144WHD (Wing) * c/w upper and lower brace arms * 1/2 x 8 x 132" steel cutting edge, center punched, * VCL steel curb shoe (each) * Standard Alkyd enamel black finish w/ corrosion protection: Medium Gloss Black * MTO reflective warning marker w/ mounting bracket * Conspicuity safety reflective tape on wing arms and on rear edge of wing. PL1415HW Gen II Body * 12.5 yd 3 water level capacity ( 15.4yd 3 w/ 10" sideboards ) shot blasted and primed only, install kit consisting of: telescopic front hoist, hoist saddle, mud flaps, dump hinge, safety prop, clearance and marker lights, box guides. * Hardox 450 high tensile body construction. * Asphalt door in tailgate * Shovel holder installed on driver's side front * Main conveyor sensor motor in lieu of Standard. w/ adapter cable * Pinned removable Aluminum fenders attached to body instead of chassis * Red/white 2" reflective tape along body fenders & across bottom tailgate * Grote ' Ultra Blue Seal ' LED lighting kit includes LED backups * Grote blue self flashing LED 6" corner post strobe * Grote amber self flashing LED 6" corner post strobe * Front LH spinner w/ reversible belt cross conveyor * Spinner clean off/anti coning device * Hinged salt extension chute * Poly lined chute * VCL manufactured air tarp kit w/ mesh tarp cover 14 ft. Prolines * 10" hardwood sideboards painted VCL black * DuPont Imron Elite finish w/ Chromate Epoxy DuPont CR2580 Primer. Paint Code: * Corner post plug for future LED upper light assembly * Pintle plate and bracing for pintle hooks rated > 30,000# MGTW * Holland PH210RA11 with air plunger and 2"tow eyes 90,000#MGTW. 27 inches ground level to the inside bottom of the pintle hook saddle. 4
* Grote quad flash strobe light complete w/o Pedestal mount, with Blue Lens * Grote quad flash strobe light complete w/o Pedestal mount, with Amber Lens * Pedestal mount for beacon light: cable tower * Re-install O.E.M. tail lights back onto rear of chassis frame * RH spinner assembly for reversible cross conveyor * Poly lined chute Air Electric Hydraulic Controls * Cirus Spread Smart Rx- 7" Color Display with SkyHawk AVL compatibility. * Dowty tandem 2PL1582PL220DVTPc/w dry valves and in-cab shifter control * Install Kit, Direct drive front mount Dowty tandem stage dry mode pump * VCL Low oil level indicator w/ in cab warning light and buzzer * MP Filtri high pressure filter ass'y w/10 micron absolute filter * Customer requested spare valves, Dual Acting * HCD 1st section c/w inlet and outlet sections * Qty (6) of HCD Remaining sections per section * Qty (7) of VCL Standard 2 wire Hydraulic hose and hose ends by number of sections Aeroquip 100R16 2 Wire GH781 with brazen resistant cover * Parker Partec hose wrap * Swivel pedestal console cab mount, air lines & fittings w/ qty (5) of Standard RMH Air Control: \PLIFT \FWING \RWING \WSLIDE \SPARE * Floor Console unit - Standard mini * Lift To Lock RMH Air Control: \HOIST * Standard RMH Air Control: \TILT.HITCH * Qty (5) of Air Switches: \TAIL \PTO1 \PTO2 \TARP \PINTLE * Cab floor stiffener plate Chassis Specification: Model Profile 2017, 7600 SFA 6X4 2010 (SF567) APPLICATION: Front Plow and Wing with Spreader MISSION: Requested GVWR: 66000. Calc. GVWR: 60000 Calc. Start / Grade Ability: 28.63% / 2.49% @ 55 MPH DIMENSION: Wheelbase: 219.00, CA: 135.50, Axle to Frame: 79.00 5
ENGINE, DIESEL: {Navistar N13} EPA 2010, SCR, 410 HP @ 1700 RPM, 1450 lb-ft Torque @ 1000 RPM, 2100 RPM Governed Speed, 410 Peak HP (Max) TRANSMISSION, MANUAL: {Fuller RTLO(F)-16913A} 13-Speed Manual; With Double Overdrive, With Air Shift and Internal Lube Oil Pump CLUTCH: {Eaton Fuller Easy-Pedal Advantage} Manual Adjust, Two-Plate, Cast Angle Spring; Ceramic, 15.5" Diameter, 7-Spring Damper, Mechanical Pull-Type Control, 1700 lb-ft Torque Capacity AXLE, FRONT NON-DRIVING: {Meritor MFS-20-133A} Wide Track, I-Beam Type, 20,000-lb Capacity AXLE, REAR, TANDEM: {Meritor MT-40-14X-4DCR} Single Reduction, 0.433"(11mm) Wall Housing Thickness, 40,000-lb Capacity, R Wheel Ends, With Driver Controlled Locking Differential in Forward-Rear and Rear- Rear Axle Gear Ratio: 4.63 TIRE, FRONT: (2) 425/65R22.5 XZY-3 (MICHELIN) 465 rev/mile, load range L, 20 ply TIRE, REAR: (8) 11R22.5 XDE M/S (MICHELIN) 497 rev/mile, load range H, 16 ply SUSPENSION, REAR, TANDEM: {Hendrickson HMX-460-54} Walking Beam Type 54" Axle Spacing; 46,000-lb Capacity, With Rubber End Bushings, Transverse Torque Rods, Less Shock Absorbers FRAME REINFORCEMENT: Outer "C" Channel, Heat Treated Alloy Steel (120,000 PSI Yield); 10.813" x 3.892" x 0.312"; (274.6mm x 98.9mm x 8.0mm); 480.0" (12192mm) Maximum OAL PAINT: Cab100GR School Bus Yellow (Std) Frame: Canyon Black (Std) 6