Last Amended on 02.09.2014 Page 1 of 10 I. DIMENSION 1. VERNIER CALIPER $ L.C. 0.01mm 0 to 300 mm 0 to 600 mm 0 to 1000 mm 8 µm 14 µm 16 µm, Slip Gauge Accessories, Gauge Block L.C. 0.02 mm 0 to 1500 mm (Inside Only 1000 mm) 24 µm 2. EXT. MICROMETER $ L.C. 0.001mm Up to 100 mm 100mm to 300 mm 300mm to 600 mm 1.3 µm 2.5 µm 10 µm, Gauge Block & Slip Gauge Accessories 600mm to 1000 mm 17 µm 3. INTERNAL MICROMETER $ 5 mm to 50 mm 50 mm to 300 mm Up to 1500 mm 6 µm 12 µm 20 µm M-88 & M-10, Gauge Block, M 8, Slip Gauge Accessories 4. PLUNGER TYPE DIAL L.C. 0.001 mm L.C. 0.001 mm Up to 25 mm 25 mm & Upto 100 mm 1.4 µm 7.2 µm Using Dial Calibration Tester, Slip Gauge Set M-88 & Micro Indicator with Comparator Stand
Last Amended on 02.09.2014 Page 2 of 10 5. LEVER TYPE DIAL L.C. 0.001 mm L.C. 0.002 mm 0 to 0.140 mm 0 to 0.2 mm 1.3 µm 1.65 µm Using Dial Calibration Tester 0 to 1 mm 6 µm 6. HEIGHT 0 to 300 mm 0 to 600 mm 0 to 1000 mm 8.7 µm 10 µm 15 µm M-88, Gauge Block M-8 Puppy Dial 7. DIAL THICKNESS L.C. 0.001 mm 0 to 1 mm 0 to 25 mm 1 µm 6 µm M - 88 8. BORE Up to 450 mm 1 mm Travel Only 4 µm Using Dial Calibration Tester & Dial Gauge 9. SNAP Up to 100 mm 2.6 µm M 88 10. PLAIN PLUG Up to 150 mm 2.2 µm Using Micro Indicator with comparator stand & Slip Gauge Set M-88 11. PLAIN RING 10mm to 100 mm 100mm to 200 mm 3 µm 3.8 µm M 88 & Slip Gauge Accessories
Last Amended on 02.09.2014 Page 3 of 10 12. FEELER Up to 1 mm 1.4 µm Using Digital Micrometer 13. MEASURING PIN SET $ Up to 25 mm 1.4 µm Using Digital Micrometer 14. STANDARD THICKNESS FOIL $ Up to 1 mm 1.4 µm Using Digital Micrometer 15. DEPTH 0 to 300 mm 8.2 µm M- 88 & Gauge block M 8 16. DEPTH MICROMETER $ L.C. 0.001 mm Up to 100 mm Up to 300 mm 1.2 µm 6 µm M- 88 & Gauge block M 8 17. DIAL INSIDE CALIPER $ L.C. 0.001mm Up to 135 mm 8 µm M 88 & Slip Gauge Accessories 18. ELECTRONIC PROBE $ L.C. 0.0001 mm Up to 25 mm 1.3 µm Using Micro Indicator with Comparator Stand & Slip Gauge Set M-88 19. DIAL CALIBRATION TESTER $ L.C. 0.002 mm Up to 25 mm 1.23µm Using Micro Indicator with Comparator Stand & Slip Gauge Set M-88
Last Amended on 02.09.2014 Page 4 of 10 20. ANGLE PROTRACTOR, BEVEL PROTRACTOR, COMBINATION SET $ L.C. 5 min Up to 360 o 4.0 minute Using Angle Gauge L.C. - 1 o 0 to 180 o 35 minute 21. THREAD PLUG Up to 100 mm 2.1 µm Using Measuring Wire & Digital Micrometer 22. MICROMETER HEAD L.C. 1 µm 0 to 50 mm 1.3 µm Using Micro Indicator with comparator Stand 23. 3 POINT MICROMETER $ L.C. 1 µm 0 to 100 mm 4 µm Using Plain Ring Gauge Set 24. V ANVIL MICROMETER $ L.C. 1 µm L.C. 10 µm 0 to 50 mm 0 to 50 mm 2.4 µm 7 µm Using Plain Plug Gauge Set 25. V BLOCK $ Parallelism Flatness Symmetry 150mm x 150mm x 150 mm 2.1 µm Using Puppy Dial & Slip Gauge Set M-88 26. STEEL SCALE $ 0 to 1500 mm 0.06 L mm L in Meter Using Length Measuring Machine
Last Amended on 02.09.2014 Page 5 of 10 27. MEASURING TAPE $ 50 mtr 0.06 L mm L in Meter Using Length Measuring Machine 28. THREAD MEASURING WIRE SET $ Upto 6.35 mm 1.4 µm Using Digital Micrometer 29. LENGTH BAR $ 0 to 500 mm 7 µm Using Dial Calibration Tester, Slip Gauge Set M-88 & Gauge Block M-8 30. FORD CUP $ Only Orifice Dia 4mm to 10 mm 11.5 µm Using Digimetic Vernier 31. PISTOL CALIPER $ L.C. 0.1 mm 0 to 100 mm 70 µm M 88 32. COATING THICKNESS L.C. 1 µm 0 to 1200 µm 1.713 µm Using Standard Thickness Foil 33. ANGLE Up to 90 11 sec Using Profile Projector 34. RADIUS Up to 25 mm 3 µm Using Profile Projector 35. SPRIT LEVEL $ L.C. 10 µm/m 200mm X 200 mm 12.08 µm/m Using Mini Level NT & Comparator Stand 36. CUBE MOULD $ 300mm X 300mmX 300 mm 12.5 µm Using Digimatic Vernier
Last Amended on 02.09.2014 Page 6 of 10 37. FLAKINESS Upto 63 mm 10 µm Using Digimatic Vernier 38. ELONGATION Upto 63 mm 10 µm Using Digimatic Vernier 39. VICKET APPARATUS $ 0 to 50 mm 578 µm M-88 40. TEST SIEVES $ Upto 1 mm Above 1mm to 100 mm 5 µm 10 µm Using Profile Projector Digimatic Vernier 41. ULTRASONIC THICKNESS Upto 200 mm 75 µm M-88 42. GLASS SCALE $ 0 to 150 mm 58 µm Using Profile Projector 43. PROFILE PROJECTOR X & Y Axis and Angular Upto 150 mm Upto 360 2 µm 42 sec M-88 & Angle Gauge 44. SURFACE PLATE All Size 2x m L & W in mm Using Mini Level NT 45. BENCH CENTER 600 mm 7.0 m Using Mandrel and Puppy Dial II. ACCELERATION & SPEED Upto 25000 RPM 0.18 % FSD Using Dig. Tachometer 1. RPM METER/ TACHOMETER # Calibrator With Dig. Tachometer
Last Amended on 02.09.2014 Page 7 of 10 III. ACCOUSTICS 1. SOUND LEVEL METER $ 94 db & 114 db 2 db Using Sound Calibrator IV. PRESSURE AND VACCUM 1. INDUSTRIAL PRESSURE GAUGE/ TRANSDUCERS WITH INDICATOR # 0 to 700 kg/cm 2 0 to 30 kg/cm 2 0 to 20 kg/cm 2 0.3% FS 0.4% FS 0.43% FS Using Digital Pressure as per DKD-R-6-1 2. MAGNEHLIC GAUGE 0 to 200 mmwc 0.37% FS Using Polltech Calibrator as per DKD-R-6-1 3. PRESSURE GAUGE 0 to 300 mmhg 0.66 % FS Using Polltech Calibrator as per DKD-R-6-1 4. VACUUM GAUGE -760 to 0 mmhg 1.0 % FS Using Digital Pressure Gauge as per DKD-R-6-1 V. TORQUE 1. TORQUE WRENCH $ 20Nm to 100 Nm 100 Nm to 1000 Nm (Type 1- Class B & Type II Class A, Class B) 1.4 Nm 9.7 Nm Using Electronic Torque Tester
Last Amended on 02.09.2014 Page 8 of 10 VI. VOLUME 1. MICRO PIPETTE $ 10 µl to 100 µl 0.06 µl Using Digital Weighing 100 µl to 1000 µl 0.06 µl Balance, Standard Weight & Distilled Water. By Gravimetric Method 2. GLASS PIPETTE $ 1 ml to 10 ml 0.08 µl Using Digital Weighing >10 ml to 25 ml 0.104 µl Balance, Standard Weight & Distilled Water. By Gravimetric Method 3. BURETTE $ 1 ml to 10 ml 0.08 µl Using Digital Weighing >10 ml to 50 ml 0.163 µl Balance, Standard Weight & Distilled Water. By Gravimetric Method 4. MEASURING 1 ml to 10 ml 0.09 µl Using Digital Weighing CYLINDER $ >10 ml to 50 ml 0.12 µl Balance, Standard Weight & Distilled Water. >50 ml to 100 ml 1.60 µl By Gravimetric Method >100 ml to 1000 ml 12.5 µl 5. MEASURING FLASK, MEASURING JAR, BEAKER $ 1 ml to 10 ml >10 ml to 50 ml >50 ml to 500 ml >500 ml to 5000 ml 0.09 µl 0.12 µl 1.52 ml 1.54 ml Using Digital Weighing Balance, Standard Weight & Distilled Water. By Gravimetric Method VII. MASS 1. SPRING BALANCE L. C. : 10 g 0 to 100 kg 16.2 g Using SS Weight F2 Class L. C. : 500 g 0 to 100 kg 800 g
Last Amended on 02.09.2014 Page 9 of 10 2. WEIGHING BALANCE L. C. : 0.1 mg 0 to 200 g 7 mg Using SS Weight of F1 Class, L. C. : 1g 0 to 20 kg 1.5 g F2 Class, M1 Class L. C.: 1 g 0 to 100 kg 14 g L. C. : 10 g 0 to 200 kg 65 g 3. WEIGHTS (CONVENTIONAL MASS) 1mg 0.06 mg Using Standard Weights 2mg 0.06 mg (F1 Class) & Precision Balance 5mg 0.06 mg By Substitution Method 10mg 0.06 mg 20mg 50mg 100mg 200mg 500mg 0.06 mg 0.09 mg 0.07 mg 0.08 mg 1 g 2g 5g 10g 20g 50g 100g 200g 500g 0.29 mg 1.15 mg 0.058 g 1 kg 0.059 g
Last Amended on 02.09.2014 Page 10 of 10 2kg 5kg 10kg 0.059 g 0.422 g 0.454 g * Measurement Capability is expressed as an uncertainty ( ) at a confidence probability of 95% $ Only in Permanent Laboratory Only for Site Calibration # The laboratory is also capable for site calibration however, the uncertainty at site depends on the prevailing actual environmental conditions and master equipment used.