Series HMI Conforms to ISO 600/ (99) or working pressures up to 0 bar Vital Technologies for Motion and Control or Cylinder Division Plant Locations See Page II. 05
As the world leader in the design and manufacture of tie-rod cylinders, Parker Cylinder Division introduces the Parker Series HMI metric hydraulic cylinder. Parker s HMI Series cylinders are designed to meet the requirements of ISO 600/ (99), 60 ar Compact Series. HMI Series cylinders may be used for working pressures up to 0 ar. Parker HMI Series cylinders are the true world standard, available all over the globe from Parker s worldwide manufacturing facilities. Whether you or your machine are in Europe, Asia, South America, Canada, Mexico, or the United States, you can rely on the engineering expertise, manufacturing experience, and commitment to quality that you ve come to expect from the Parker Cylinder Division. or additional information call your local Parker Cylinder Distributor. 06
Series HMI Standard eatures and Specifications ISO 600/ mounting interchangeable standard mounting styles Up to rod sizes per bore Wide range of mounting accessories Up to male and female rod end threads per bore ore sizes 5mm to 00mm Strokes available in any practical stroke length eatures, Specifications and Mountings Working pressure up to 0 bar Piston rods mm to 40mm Single and Double rod designs Cushions available at either end Temperature Range -0 C to 50 C depending on seal type Seal types to suit a wide variety of operating environments In line with our policy of continuing product improvement, specifications in this catalog are subject to change. Available Mountings and Where To ind Them ISO MX ISO MX ISO MX T Page TC Page TD Page ISO ME5 ISO ME6 ISO MS Page HH Page C Page ISO MP ISO MP ISO MP5 Page 4 Page 4 S Page 4 ISO MT ISO MT ISO MT4 D Page 5 D Page 5 DD Page 5 or Cylinder Division Plant Locations See Page II. 07
Design eatures and enefits Parker Series HMI 5 6 8 Piston Rod land seal life is maximized by manufacturing piston rods from precision ground, high tensile carbon alloy steel, hard chrome plated and polished to 0.µm max. Piston rods are induction case hardened to Rockwell C54 minimum before chrome plating, resulting in a dent-resistant surface. Parker s ewel land Continuous lubrication, and therefore longer gland life, are provided by the long bearing surface inboard of the primary 4 7 & 8 cylinder. The double lip wiperseal acts as a secondary seal, trapping excess lubricating film in the chamber between the wiper and lip seals. Its outer lip prevents the ingress of dirt into the cylinder, extending the life of gland and seals. The TS-000 is manufactured from an enhanced polyurethane, giving efficient retention of pressurized fluid and long service life. 4 Cylinder ody Strict quality control standards and precision manufacture ensure that all tubes meet rigid standards of straightness, roundness and surface finish. The steel tubing is surface finished to minimize internal friction and prolong seal life. 5 Cylinder ody Seals To make sure that the cylinder body remains leaktight, even under pressure shock conditions, Parker utilizes pressureenergized body seals. 6 One-Piece Piston Side loading is resisted by the wide bearing surfaces of the pistons. A long thread engagement secures the piston to the piston rod and, as an added safety feature, pistons are secured by an anaerobic adhesive. 7 9 seal. The ewel gland, complete with rod seals, can easily be removed without dismantling the cylinder, so servicing is quicker and therefore more economical. Rod Seals The TS-000 primary seal has a series of sealing edges which take over successively as pressure increases, providing efficient sealing under all operating conditions. On the return stroke the serrations act as a check valve, allow-ing the oil adhering to the rod to pass back into the 7 Cushioning Progressive deceleration is available by using profiled cushions at the head and cap see Section C for details. The head end cushion is self aligning, while the polished cap end spear is an integral part of the piston rod. 8 loating Cushion ushings and Sleeves Closer tolerances and therefore more effective cushioning are permitted by the use of a floating cushion sleeve at the head end of the cylinder, and a floating cushion bushing at the cap end. A slotted cushion sleeve at the head end and the floating bronze cushion bushing in the cap, provide minimum fluid restriction at the start of the return stroke. This allows full pressure to be applied over the entire area of the piston, providing full power and fast cycle times. or additional information call your local Parker Cylinder Distributor. 08
9 Cushion Adjustment Needle valves are provided at both ends of the cylinder for precise cushion adjustment. 6 mm bores and smaller contain cartridge cushion assembly shown below. Design eatures and enefits Piston Seals Parker s style piston is a single seal design which incorporates two wear strips. This design provides smooth operation, long bearing life, and high load carrying capacity. Air leeds Available as an option at both ends, the air bleeds are recessed into the head and cap. Servo Cylinders Servo cylinders permit fine control of acceleration, velocity and position in applications where very low friction and an absence of stick-slip are required. They may be used in conjunction with integral or external transducers. Servo cylinders combine low friction piston and gland seals with specially selected tubes and rods. or low-friction applications consult factory. Seal Classes To accommodate the many types of fluids and the varying temperature ranges used in industry, Parker offers a range of rod gland, piston and body seals. These are described in detail in Section C of this catalog. land Drains The accumulation of fluid behind the gland wiperseal of long stroke cylinders, or cylinders with constant back pressure, can be relieved by specifying the option of a gland drain. A port between the wiperseal and primary seal allows fluid to be piped back to a reservoir. y fitting a transparent tube between the port and the reservoir, fluid loss from concealed or inaccessible cylinders can be monitored to provide an early indication of the need for gland servicing. land drains are described in greater detail in Section C of this catalog. or Cylinder Division Plant Locations See Page II. 09
Mounting Styles Parker Series HMI ISO Cylinder Mounting Styles and Where to ind Them The standard range of Parker Series HMI cylinders comprises ISO mounting styles, to suit the majority of applications. eneral guidance for the selection of ISO cylinders is given below, with dimensional information about each mounting style shown on the following pages. Applicationspecific mounting information is shown in the mounting information section, Section C of this catalog. Extended Tie Rods Cylinders with T, TC and TD mountings are suitable for straight line force transfer applications, and are particularly useful where space is limited. or compression (push) applications, cap end tie rod mountings are most appropriate; where the major load places the piston rod in tension (pull applications), head end mounting styles should be specified. Cylinders with tie rods extended at both ends may be attached to the machine member from either end, allowing the free end of the cylinder to support a bracket or switch. lange Mounted Cylinders These cylinders are also suitable for use on straight line force transfer applications. Two flange mounting styles are available, offering either a head flange () or a cap flange (HH). Selection of the correct flange mounting style depends on whether the major force applied to the load will result in compression (push) or tension (pull) stresses on the piston rod. or compression-type applications, the cap mounting style is most appropriate; where the major load places the piston rod in tension, a head mounting should be specified. oot Mounted Cylinders Style C, foot mounted cylinders do not absorb forces on their centerline. As a result, the application of force by the cylinder produces a moment which attempts to rotate the cylinder about its mounting bolts. It is important, therefore, that the cylinder should be firmly secured to the mounting surface and that the load should be effectively guided to avoid side loads being applied to rod gland and piston bearings. A thrust key modification may be specified to provide positive cylinder location. Pivot Mountings Cylinders with pivot mountings, which absorb forces on their centerlines, should be used where the machine member to be moved travels in a curved path. Pivot mountings may be used for tension (pull) or compression (push) applications. Cylinders using a fixed clevis, styles and, may be used if the curved path of the piston rod travel is in a single plane; for applications where the piston rod will travel in a path on either side of the true plane of motion, a spherical bearing mounting S is recommended. Trunnion Mounted Cylinders These cylinders, styles D, D and DD, are designed to absorb force on their centerlines. They are suitable for tension (pull) or compression (push) applications, and may be used where the machine member to be moved travels in a curved path in a single plane. Trunnion pins are designed for shear loads only and should be subjected to minimum bending stresses. Styles T, TC, TD ISO Styles MX, MX, MX Styles, HH ISO Styles ME5, ME6 Style C ISO Style MS Styles,, S ISO Styles MP, MP, MP5 Styles D, D, DD ISO Styles MT, MT, MT4 T HH C D or additional information call your local Parker Cylinder Distributor. 0
Parker Thread Styles 4 & 7 All Except Mount Parker Thread Style 9 All Except Mount A NA KK MM D Wrench lats D Wrench lats VE VE NA K MM A Piston Rod End Dimensions Parker Thread Styles 4 & 7 Mount RD NA KK Parker Thread Style 9 Mount MM Style 4 Style 7 Style 9 Mount Only ore Rod Rod D NA VE f9 VL RD φ No. φ KK A KK A K A V min f8 5 M0x.5 4 - - M8x 4 4 0 6 8 M4x.5 8 M0x.5 4 Mx.5 8 0 5 7 6 5 8 6 0 4 Mx.5 6 - - M0x.5 6 6 M6x.5 Mx.5 6 M6x.5 4 8 5 4 0 40 8 M4x.5 8 - - Mx.5 8 0 5 7 6 6 5 6 8 M0x.5 8 M4x.5 8 M0x.5 8 4 6 0 M6x.5 - - M6x.5 4 8 6 50 6 M7x 6 M6x.5 M7x 6 50 0 4 5 4 4 74 9 6 8 M0x.5 8 M6x.5 M0x.5 8 4 6 6 8 M0x.5 8 - - M0x.5 8 4 6 75 6 6 45 Mx 45 M0x.5 8 Mx 45 60 9 4 9 48 4 6 88 6 M7x 6 M0x.5 8 M7x 6 50 0 4 5 9 6 M7x 6 - - M7x 6 50 0 4 5 8 5 80 56 M4x 56 M7x 6 M4x 56 7 48 54 9 5 4 0 05 9 45 Mx 45 M7x 6 Mx 45 60 9 4 9 45 Mx 45 - - Mx 45 60 9 4 9 9 7 00 70 M48x 6 Mx 45 M48x 6 88 6 68 57 5 0 5 56 M4x 56 Mx 45 M4x 56 7 48 54 9 7 56 M4x 56 - - M4x 56 7 48 54 9 05 9 0 5 90 M64x 85 M4x 56 M64x 85 08 80 88 57 5 70 M48x 6 M4x 56 M48x 6 88 6 68 50 0 70 M48x 6 - - M48x 6 88 6 68 5 0 60 0 M80x 95 M48x 6 M80x 95 00 08 57 5 90 M64x 85 M48x 6 M64x 85 08 80 88 70 7 5 90 M64x 85 - - M64x 85 08 80 88 50 0 00 40 M00x M64x 85 M00x 6 8 8 57 5 0 M80x 95 M64x 85 M80x 95 00 08 0 7 5 A D Wrench lats RD NA K D Wrench lats VE V VL A VE V VL MM MM Parker Thread Styles 4 & 7 The smallest diameter rod end thread for each bore size is designated Style 4 when supplied with a No. rod. When the same rod end thread is supplied with a No. or No. rod, it is designated Style 7. Parker Thread Style 9 Short Stroke Cylinders Style 9 (female) rod ends should not be used on 60mm or 00mm bore cylinders with a stroke of 50mm or less. Please consult the factory, with details of the application. Parker Thread Style Non-standard piston rod ends are designated 'Style '. A dimensional sketch or description should accompany the order. Please specify dimensions KK or K, A, rod stand out and thread type. Piston Rod End Data and Threads 5 & mm ore Cylinders 5mm E E 5mm extra height applies to port face at head end only. land Retainer 60 and 00mm ore On all 60mm and 00mm bore ISO mounting styles except T and TD, the gland retainer is separately bolted to the head, as shown. 5mm or Cylinder Division Plant Locations See Page II.
Extended Tie Rod Mountings Parker Series HMI WH Z + Stroke P + Stroke 4 AA T Style T Tie Rods Extended Head End (ISO Style MX) DD T K T Z + Stroke P + Stroke DD AA 4 T Style TC Tie Rods Extended Cap End (ISO Style MX) K T WH Z + Stroke P + Stroke DD 4 AA T Style TD Tie Rods Extended oth Ends (ISO Style MX) T T Head depth increased by 5mm to accommodate port on 5mm and mm bore cylinders see page Dimensions T, TC & TD See also Rod End Dimensions, page ore φ 5 40 50 6 80 00 5 60 00 AA DD E T K T WH + Stroke SP/ inches P Z 40 9 M5x0.8 40 /4 0 0 40 5 4 8. 5 5 50 5 4 47 4 M6x 45 /4 0 0 40 5 5. 5 5 60 56 8 59 5 M8x 6 /8 0 0 45 8 6.5 4.7 5 5 6 7 5 74 46 Mx.5 75 / 6 6 45 8 0 5. 4 5 67 74 59 9 46 Mx.5 90 / 6 6 45 8 0 64. 48 7 80 68 7 59 M6x.5 5 /4 0 0 50 45 8.7 5 77 9 90 7 59 M6x.5 0 /4 50 45 96.9 57 5 8 0 0 78 8 Mx.5 65 58 58 8 5.9 57 5 86 7 9 9 M7x 05 5 5 58 58 54.9 57 86 0 45 69 5 M0x 45 -/4 5 5 76 76 4 90. 57 98 65 99 or additional information call your local Parker Cylinder Distributor.
lange and Side Lugs Mountings Z + Stroke Z + Stroke P + Stroke UO 4 R Style Head Rectangular lange (ISO Style ME5) K Ø T Z + Stroke P + Stroke UO R 4 Style HH Cap Rectangular lange (ISO Style ME6) K Z + Stroke Z + Stroke P + Stroke Ø T A thrust key may be used with this mounting style. 4 SØ ST LH Style C Side Lugs (ISO Style MS) SW XS SS + Stroke SW K TS US Head depth increased by 5mm to accommodate port on 5mm and mm bore cylinders, except Style in port positons and 4 see page Dimensions, HH & C See also Rod End Dimensions, page ore φ 5 40 50 6 80 00 5 60 00 E K LH R S ST SW T TS UO US XS + Stroke SP/ inches h0 P SS Z Z 40 /4 0 5.5 40 5 4 9 7 6.6 8.5 8 5 54 65 7 5 50 5 7 4 45 /4 0 6.6 40 5 5 9.5 0 58 6 70 84 5 45 60 56 7 7 8 6 /8 0 45 8 6.5 4.5 0 87 8 0 0 5 45 6 7 98 66 5 75 / 6 4 45 8 0 7 5 4 9 05 0 0 7 4 54 67 74 9 76 59 90 / 6 4 45 8 0 44 65 8 6 7 7 4 45 6 48 65 7 80 86 85 68 5 /4 0 8 50 45 57 8 8 6 7 49 49 80 86 5 68 77 9 05 90 0 /4 8 50 45 6 97 6 6 7 00 6 57 79 8 0 0 5 0 65 58 58 8 8 6 6 08 0 50 54 57 79 86 7 60 05 5 6 58 58 0 55 8 9 5 60 00 8 57 86 86 0 0 79 45 45 -/4 5 76 76 4 90 9 44 5 00 60 8 57 9 98 65 7 6 99 or Cylinder Division Plant Locations See Page II.
Pivot Mountings Parker Series HMI Pivot pin not supplied ZC + Stroke Z + Stroke P + Stroke CD 4 Style Cap ixed Eye (ISO Style MP) EW Supplied complete with pivot pin K XC + Stroke ZC + Stroke Z + Stroke P + Stroke CD LR L M Hole H9 Pin f8 MR 4 Style Cap ixed Clevis (ISO Style MP) CW C CW K XC + Stroke LR L M MR Pivot pin not supplied ZO + Stroke Z + Stroke P + Stroke CX 4 Style S* Cap ixed Eye (ISO Style MP5) EP EX K XO + Stroke LT MS Head depth increased by 5mm to accommodate port on 5mm and mm bore cylinders see page *Parker Style S is also known as Style Sd under Parker s European model code system Dimensions, & S See also Rod End Dimensions, page ore φ 5 40 50 6 80 00 5 60 00 C CD CW CX E EP EW EX K L LR LT M MR MS + Stroke SP/ A6 H9 inches h4 max P XC XO ZC Z ZO 0 6-0.008 40 /4 8 0 0 40 5 4 6 0 0 5 50 5 7 0 7 4 50 6 8 6-0.008 45 /4 6 4 0 40 5 5 9 7 0 5.5 5 60 56 47 48 59 8 70.5 0 4 0 0-0.0 6 /8 0 6 0 45 8 6.5 9 7 5 4 6 9 5 6 7 7 78 86 5 07 0 0 5 5-0.0 76 / 7 0 0 6 45 8 0 9 0 5 4 67 74 9 90 59 0 0 5 0-0.0 90 / 9 0 6 45 8 0 9 8 0 5 40 48 7 80 00 06 0 68 46 40 8 0 40-0.0 5 /4 40 8 0 50 45 9 4 48 8 4 50 5 77 9 9 8 57 90 88 50 6 5 50-0.0 0 /4 0 50 5 50 45 54 50 58 6 44 6 57 8 0 57 6 9 0 60 45 0 60-0.05 65 8 60 44 58 58 8 57 5 7 45 5 80 57 86 7 89 04 4 84 70 56 5 80-0.05 05 47 70 55 5 58 58 6 59 9 59 59 00 57 86 0 08 7 67 45 47 80 70 40 00-0.00 45 -/4 57 80 70 5 76 76 4 8 78 6 70 76 0 57 98 65 8 45 45 99 55 or additional information call your local Parker Cylinder Distributor. 4
Trunnion Mountings Z + Stroke Z + Stroke P + Stroke Notes: A one-piece head and retainer is used on 00mm-00mm bore sizes dimension. On 60 and 00mm bores, the bolted gland is recessed, with tie rods screwed into the head. R mm 4 TD Style D Head Trunnion (ISO Style MT) W X Z + Stroke Z + Stroke Z + Stroke P + Stroke K TL TC Note: On 00-00mm bore cylinders, dimension becomes. Z replaces Z, and tie rods are screwed directly into the cap. TL R mm 4 TD Style D Cap Trunnion (ISO Style MT) X + Stroke K TL TC TL Z + Stroke Z + Stroke P + Stroke D R mm T 4 TD Style DD Intermediate ixed Trunnion (ISO Style MT4) XI K TL TM TL Head depth increased by 5mm to accommodate port on 5mm and mm bore cylinders see page Dimensions to be specified by customer Dimensions D, D & DD See also Rod End Dimensions, page ore φ 5 40 50 6 80 00 5 60 00 D E K TC TD TL TM T W X + Stroke Style DD Min XI SP/ inches f8 P X Z Z Z min stroke dim n 0 40 /4 0 40-5 - 4 8 0 48 45-5 44 50 5 0 4-0 78 5 45 /4 0 40-5 - 5 44 6 55 54-5 54 60 56 5 8-7 0 90 0 6 /8 0 45-8 - 6.5 6 0 6 76 76-5 57 6 7 4 5-66 5 97 40 76 / 6 45-8 - 0 76 5 0 89 89-4 64 67 74 40 59-76 5 07 40 90 / 6 45-8 - 0 89 5 00 95-48 70 7 80 49 68-85 5 4 50 5 /4 0 50-45 50 4 40 7 7-5 76 77 9 68 90 94 0 7 60 0 /4 50 7 45 58 7 50 40 40 40 5 57 7 8 0 87 0 6 5 0 8 7 65 58 80 58 7 8 65 6 50 78 78 5 57 75 86 7 09 45 60 5 5 90 05 5 58 88 58 88 0 80 6 5 6 57 75 86 0 0 45 75 79 0 6 0 45 -/4 5 76 08 76 08 4 4 00 80 79 80 57 85 98 65 76 99 0 6 0 90 or Cylinder Division Plant Locations See Page II. 5
Double Rod Cylinders Parker Series HMI ZM + ( X Stroke) P + Stroke LV + Stroke K Double Rod Cylinder Available with Styles T, TD,, C, D, DD (Style C illustrated) SW XS SV + Stroke SW Mounting Styles and Codes Double rod cylinders are denoted by a K in the ISO cylinder model code. Dimensions To obtain dimensional information for double rod cylinders, first select the desired mounting style by referring to the corresponding single rod model. Dimensions for the appropriate single rod model should be supplemented by those from the table opposite to provide a full set of dimensions. Minimum Stroke Length Style 9 Rod End Where a style 9 (female) piston rod end is required on a double rod cylinder with a stroke of 80mm or less, and a bore of 80mm or above, please consult the factory. Cushioning Double rod cylinders can be supplied with cushions at either or both ends. Cushioning requirements should be specified by inserting a C in the ordering code. See cushioning section, Section C of this catalog. Double Rod Cylinders or double rod cylinders, specify rod number and rod end symbols for both piston rods. A typical model number for a double rod cylinder would be: 00 K HMI R 4 M 4 M 5 M 44 ore Rod Add Stroke Add x Stroke φ No. MM φ LV P SV ZM 5 04 5 88 54 8 4 08 56 88 78 40 8 5 7 05 95 8 50 6 5 74 99 07 8 8 6 45 7 80 9 6 6 80 56 44 9 0 46 45 45 00 70 5 0 07 65 56 56 5 90 75 7 89 70 70 60 0 88 0 0 0 90 90 00 40 4 60 7 56 0 or additional information call your local Parker Cylinder Distributor. 6
Accessory Selection Accessories for the rod end of a cylinder are selected by reference to the rod end thread, while the same accessories, when used at the cap end, are selected by cylinder bore size. See tables of part numbers below, and on the following pages. The rod clevises, plain rod eyes and spherical bearings fitted as accessories to the rod end have the same pin diameters as those used at the cylinder cap ends of the corresponding mounting styles, and S when fitted with the No. rod, or the No. or No. rods with Style 7 rod end. Rod and Cap End Accessories Accessories for the HMI ISO cylinder include: Rod End rod clevis, eye bracket and pivot pin plain rod eye, clevis bracket and pivot pin rod eye with spherical bearing Cap End eye bracket for style mounting clevis bracket for style mounting pivot pin for eye bracket and clevis bracket ØH Rod Clevis, Eye racket and Pivot Pin Thread Rod Eye Pivot Nominal Weight KK Clevis racket Pin orce kn kg M0x.5 4447 44808 4477 8 0. Mx.5 4448 44809 4478.5 0.6 M4x.5 4449 4480 4479 0 0.8 M6x.5 4450 448 4480. M0x.5 445 448 4480 50.7 M7x 445 448 448 80 5.9 Mx 445 4484 448 5 9.4 M4x 4454 4485 448 00 7.8 M48x 4455 4486 4484 0 6.8 M64x 4456 4487 4485 500 9.0 CK T CR Rod Clevis UD EM ER max AA UD Thread KK CL CM L LE T Eye racket LE AV min CE MR CK Rod Clevis Dimensions Eye racket Dimensions Pivot Pin for Clevis racket and Plain Rod Eye Dimensions EL EK Accessories Part AV CE CK CL CM CR ER KK LE Weight No. H9 A6 kg 4447 4 0 6 0 M0x.5 4 0.08 4448 6 6 4 6 7 Mx.5 9 0.5 4449 8 8 4 4 0 0 7 M4x.5 9 0. 4450 54 0 6 0 50 9 M6x.5.0 445 8 60 0 6 0 50 9 M0x.5. 445 6 75 8 8 40 60 4 M7x 9. 445 45 99 6 0 50 80 50 Mx 54.6 4454 56 45 60 0 5 M4x 57 5.5 4455 6 6 56 4 70 59 M48x 6 7.6 4456 85 68 70 6 80 46 78 M64x 8.0 Part CK EM L MR LE AA H T UD No. H9 h max min 44808 0 40 5.5 8. 40 44809 6 9 7 9 47 6.6. 45 4480 4 0 9 7 9 59 9 4.7 65 448 0 0 48 9 74.5 5. 75 448 0 0 48 9 9.5 64. 90 448 8 40 59 4 9 7 7.5 8.7 5 4484 6 50 79 50 54 7 7.5 96.9 0 4485 45 60 87 5 57 78 6 5.9 65 4486 56 70 0 59 6 9 0 54.9 05 4487 70 80 78 8 69 90. 40 Part EK EL Weight No. f8 kg 4477 0 9 0.0 4478 7 0.05 4479 4 45 0.08 4480 0 66 0. 448 8 87 0.4 448 6 07.0 448 45 9.8 4484 56 49 4. 4485 70 69 6.0 Eye racket Cap End Mounting for Style ore Eye racket Nominal orce Weight φ kn kg 5 44808 8 0. 44809.5 0. 40 4480 0 0.4 50 448.0 6 448 50.4 80 448 80. 00 4484 5 5.6 5 4485 00 0.5 60 4486 0 5.0 00 4487 500 0.0 or Cylinder Division Plant Locations See Page II. 7
Accessories Parker Series HMI Plain Rod Eye, Clevis racket and Pivot Pin Thread Plain Clevis Nominal Weight KK Rod Eye racket Pivot Pin orce kn kg M0x.5 4457 4646 4477 8 0.5 Mx.5 4458 4647 4478.5.0 M4x.5 4459 4648 4479 0. M6x.5 4460 4649 4480. M0x.5 446 4649 4480 50.8 M7x 446 4650 448 80 6.9 Mx 446 465 448 5.5 M4x 4464 465 448 00 6.0 M48x 4465 465 4484 0 47.0 M64x 4466 4654 4485 500 64.0 Plain Rod Eye/Knuckle Dimensions Part AW CA C CD CK EM ER KK LE Weight No. H9 h kg 4457 4 8 9 0 M0x.5 0.08 4458 6 6 6 7 Mx.5 9 0.5 4459 8 8 0.5 4 0 7 M4x.5 9 0. 4460 54 0 7.5 0 0 9 M6x.5 0.5 446 8 60 0 0 0 0 9 M0x.5. 446 6 75 40 5 8 40 4 M7x 9.5 446 45 99 50 5 6 50 50 Mx 54.5 4464 56 65 50 45 60 5 M4x 57 4. 4465 6 6 90 56 56 70 59 M48x 6.8 4466 85 68 0 70 70 80 78 M64x 8 7.0 Clevis racket Dimensions Part CK CM CW L MR H LE RC T UR UH No. H9 A6 max min 4646 0 6 5.5 8 47 5 60 4647 6 8 9 7 6.6 9 4 57 45 70 4648 4 0 0 9 7 9 9 0 68 55 85 4649 0 0 5 48 9.5 45 0 80 5 4650 8 40 0 59 4 7.5 9 60 5 00 70 465 6 50 5 79 50 7.5 54 75 67 0 00 465 45 60 0 87 5 6 57 90 8 50 0 465 56 70 5 0 59 0 6 05 4 80 00 4654 70 80 40 78 8 0 00 00 60 Clevis racket or Style ore Clevis racket Nominal orce Weight φ kn kg 5 4646 8 0.4 4647.5 0.8 40 4648 0.0 50 4649.5 6 4649 50.5 80 4650 80 5.0 00 465 5 9.0 5 465 00 0.0 60 465 0.0 00 4654 500 4.0 Plain Rod Eye/Knuckle Clevis racket T UH CK ØH CK CD CW UR CM RC ER max CD CW KK Thread Pivot Pin for Clevis racket and Plain Rod Eye Dimensions EL EK EM h C L LE AW min LE CA MR Part EK EL Weight No. f8 kg 4477 0 9 0.0 4478 7 0.05 4479 4 45 0.08 4480 0 66 0. 448 8 87 0.4 448 6 07.0 448 45 9.8 4484 56 49 4. 4485 70 69 6.0 or additional information call your local Parker Cylinder Distributor. 8
Rod Eye with Spherical earing, Mounting racket and Pivot Pin Thread Rod Eye with Mounting racket Nominal Weight KK Spherical earing and Pivot Pin orce kn kg M0x.5 4554 4550 8 0. Mx.5 4555 455.5 0. M4x.5 4556 455 0 0.4 M6x.5 4557 455 0.7 M0x.5 4558 4554 50. M7x 4559 4555 80. Mx 4560 4556 5 4.4 CN AX EN EU KK N CH L X A E P MA Torque Accessories Section X- M4x 456 4557 00 8.4 M48x M64x 456 456 4558 4559 0 500 5.6 8.0 Rod Eye with Spherical earing All spherical bearings should be re-packed with grease when servicing. In unusual or severe working conditions, consult the Rod Eye with Spherical earing Dimensions factory regarding the suitability of the bearing chosen. Part E L MA max A max AX min CH CN EN EU U KK N max No. max min Nm P 4554 40 5 0 4-0.008 0 -.0 8 M0x.5 6 7 0 M6 4555 45 7.5 48 6-0.008 4 -.0 Mx.5 0 0 M6 4556 55 9 7.5 58 0-0.0 6 -.0 7 M4x.5 5 5 5 M8 4557 6.5 68 5-0.0 0 -.0 7 7 M6x.5 0 0 5 M8 4558 80 9 40 85 0-0.0 -.0 9 9 M0x.5 5 6 45 M0 4559 90 7 50 05 40-0.0 8 -.0 M7x 45 45 45 M0 4560 05 46 6.5 0 50-0.0 5 -.0 0 0 Mx 58 55 80 M 456 4 57 80 50 60-0.05 44 -.05 8 8 M4x 68 68 60 M6 456 56 64 0.5 85 80-0.05 55 -.05 47 47 M48x 9 90 0 M0 456 90 86 0 40 00-0.00 70 -.00 57 57 M64x 6 0 50 M4 U Mounting racket and Pivot Pin Dimensions - or Style S Part C C CO CP M O L H KC L L LO RE SR TA U UK No. K7/h6 +0., +0. N9 js js4 js 0, +0.0 js max js 4550 0 0 0 40 6 46 9. 8 9 56 55 40 75 60 455 6 4 6 40 50 8 6 4. 7 8 74 70 6 55 95 80 455 0 6 6 50 55 0 64 4 4. 9 40 80 85 0 58 0 90 455 5 0 5 60 65 78 6 5.4 48 49 98 00 5 70 40 0 4554 0 5 70 85 4 97 8 5.4 6 6 0 5 0 90 60 5 4555 40 8 6 80 00 4 8.4 7 7 48 5 40 0 90 70 4556 50 5 6 00 5 5 55 0 8.4 90 9 90 70 50 45 40 5 4557 60 44 50 0 50 5 87 9.4 08 0 5 00 60 85 70 60 4558 80 55 50 60 90 5 55 45.4 40 4 95 40 80 60 0 40 4559 00 70 6 00 0 5 85 48.4 50 5 5 00 00 00 400 400 Cap Mounting racket and Pivot Pin ore Mounting racket Nominal orce Weight φ and Pivot Pin kn kg 5 4550 8 0.6 455.5. 40 455 0. 50 455. 6 4554 50 6.5 80 4555 80.0 00 4556 5.0 5 4557 00 7.0 60 4558 0 79.0 00 4559 500 40.0 SR M KC O Mounting racket and Pivot Pin CO L LO TA UK C H Ø CP C RE U L L or Cylinder Division Plant Locations See Page II. 9
Model Numbers How to Order ISO Cylinders Parker Series HMI Data Required On All Cylinder Orders When ordering Series HMI cylinders, be sure to specify each of the following requirements: (NOTE: Duplicate cylinders can be ordered by giving the SERIAL NUMER from the nameplate of the original cylinder. actory records supply a quick, positive identification.) a) ore Size b) Mounting Style Specify your choice of mounting style as shown and dimensioned in this catalog. If double rod is required, specify with double rod. c) Series Designation ( HMI ) d) Length of Stroke e) Piston Rod Diameter Call out rod diameter or rod code number. In Series HMI cylinders, standard rod diameters (Code No. ) will be furnished if not otherwise specified, unless length of stroke makes the application questionable. f) Piston Rod End Thread Style Call out thread style number or specify dimensions. Thread style number 4 will be furnished if not otherwise specified. g) Cushions (if required) Specify Cushion-head end, Cushion-cap end or Cushion-both ends as required. If cylinder is to have a double rod and only one cushion is required, be sure to specify clearly which end of the cylinder is to be cushioned. h) Piston Parker style pistons are standard. luorocarbon also available. i) Ports SP (ISO 8) are standard. j) luid Medium Series HMI hydraulic cylinders are equipped with seals for use with hydraulic oil. If other than hydraulic oil will be used, consult factory. ADDITIONAL DATA is required on orders for cylinders with special modifications. or further information, consult factory. Service Policy On cylinders returned to the factory for repairs, it is standard policy for the Cylinder Division to make such part replacements as will put the cylinder in as good as new condition. Should the condition of the returned cylinder be such that expenses for repair would exceed the costs of a new one, you will be notified. Address all correspondence to Service Department at your nearest regional plant listed in the pages of this catalog. Certified Dimensions Parker Cylinder Division guarantees that all cylinders ordered from this catalog will be built to dimensions shown. All dimensions are certified to be correct, and thus it is not necessary to request certified drawings. or additional information call your local Parker Cylinder Distributor. 0
Series HMI Model Numbers How to Develop and Decode Them Parker Series HMI cylinders can be completely and accurately described by a model number consisting of coded symbols. To develop a model number, select only those symbols that represent the cylinder required, and place them in the sequence indicated below. eature Description Page Symbol ore Millimeters Cushion Head If required C C Double Rod If required 6 K Mounting Style Head Tie Rods Extended T Cap Tie Rods Extended TC oth Ends Tie Rods Extended TD Head Rectangular lange Cap Rectangular lange HH Side Lugs C Cap ixed Eye 4 Cap ixed Clevis 4 Cap ixed Eye with Spherical earing* 4 S* Head Trunnion 5 D Cap Trunnion 5 D Intermediate ixed Trunnion 5 DD Mounting Thrust Key for Style C Modifications mounting only C06 P Series Series name HMI Ports SP (ISO 8) standard C5 R SPT (Taper Thread) C5 Metric Thread C5 Metric Thread per ISO 649 C5 SAE Straight Thread O-ring Port C5 T NPT (Dry Seal Pipe Thread) C5 U SAE lange Ports (000 PSI) C5 P Piston -Style Low riction filled PTE seals (standard) 08 Special One or more of the following: S eatures land Drain Port C7 Oversize Ports C4 Rod End ellows C7 Stop Tube C09 Stroke Adjuster C7 Tie Rod Supports C07 Water Service Modifications C6 Or to detailed descriptions or drawings supplied by customer Piston Rod Rod No. Number Rod No. Rod No. Piston Rod End Style 4 4 Style 7 7 Style 9 9 Style (Special) Please supply description or drawing Rod Thread Metric (standard) M Cushion Cap If required C C ross Stroke Millimeters - luid Mineral Oil HH, HL, HLP, HLP-D, Medium HM, HV, MIL-H-5606 Oil, ISO Air, Nitrogen roup C6 M 674/4 (98) luorocarbon roup 5 C6 D Port Head position -4 C4 Positions Cap position -4 C4 Air leeds Head position -4 C4 4 Cap position -4 C4 4 No Air leed C4 00 Model Numbers Note: Page numbers with a letter prefix, ie: C77, are located in section C of this catalog. 80 C K C P HMI R S 4 M C 0 M 44 Key: Example Essential information Optional features *Mounting Style S is also known as Parker Style Sd in Parker s European model code system. Specify XI dimension. or Cylinder Division Plant Locations See Page II.