Product Data Application Method - RPL (Raised Panel) Labels are innovative labels specifically designed to replace engraved and plotted plates for the identification of electrical components, electrical cabinets, push button, patch panels, etc. RPL labels save time and money by allowing you to print name plates exactly when you want them instead of having to order pre-printed name plates and holding stock. This process is a least 7 to 10 times faster than engraving and delivers up to 50 percent cost reduction. Rapid Pre-Print Service from Siegrist. If you would rather hand everything over to us, we offer a fast 24/48/72 hour Pre-Print Service. Simply email us your schedules and we will do the rest. Good resistance against scratching, smearing and rubbing Excellent UV resistance on printed image High tack adhesive, suitable for uneven (rough) surfaces Easier, faster, and more cost-effective than engraved metal plates Up to 6 colours: black, white, yellow, silver, red and green Good chemical resistance against alcohols and diesel oils Glossy topcoat for a smart and professional look Supplied already formatted for printing on ITAG Printing System Storage Conditions Stored in its original packaging in an environment below 21 C and 50% RH. Damp conditions, excessive heat and-or freezing conditions should be avoided. Film material stable for 2 years.the storage stability is one year after delivery on the adhesive foam. Printer and Ribbon Recommended Itag printer 300 Dpi STP-A3-300-S-NC-S STP-A4+-300Z-S-NC-S High Performance Ribbon 510 Series Ribbon Black 510 Series Ribbon White 510 Series Ribbon Red Using Eurolabel label software enables quick turn out of serialised groups of labels using pre-defined templates. RPL can be supplied in a custom width from 27mm to 140mm and eight different heights from 8mm to 100mm. Available colours White Silver Yellow Custom sizes and colours on request. Please contact us for further information Application Temperature Recommended application temperature 18 C to 35 C Operating Temperature Foam / Adhesive Temperature -40 C to 100 C Operating Temperature Polyester Film Temperature -40 C to 150 C RoHS Restriction of Hazardous Substances (RoHS) Directive 2005/618/EC, amendment to RoHS Directive 2002/95/EC.. None of the substances are knowingly used or added in the manufacturing process. TDS 1117 ISS. 1.4
Performance Properties Performance Properties Test Methods High Service Temperature 1000 hours at 100 C (212 F) Low Service Temperature 1000 hours at -20 C (-20 F) Humidity Resistance 1000 hours at 37 C (100 F), 95% R.H. UV Light Resistance 1000 hours in UV light chamber Weatherability 1000 hours in QUV (ASTM G-53) Abrasion Resistance Method Taber Abrasion Tester CS 10 + 500 g load/arm White RPL/ 510 Ribbon Black Black RPL/ 510 Ribbon White Number of cycles until print Number of cycles until is illegible 180 print is illegible 75 Metallised RPL/ 510 Ribbon Black Number of cycles until print is illegible 180 Material: RPL is a glossy thermal transfer printable polyester tag based on a double sided adhesive tape with a compressible foam carrier and a permanent acrylic adhesive. Standard colours: White, Yellow, Silver. Other colours on request Physical Properties Thickness Peel Strength at room temperature Stainless Steel Smooth ABS Powdercoated surface Polyethylene Drop Shear Tack Test Method ASTM D 1000 - Substrate - Foam tape - Total ASTM D 1000 PSTC-7 (except use 1/2" x 1" sample) ASTM D2979 Polyken Probe Tack ( 1 s dwell, 1 cm/s separation ) Typical Value 0.200 mm (0.0079 inch) 0.450 mm (0.0177 inch) 0.650 mm (0.0256 inch) 35 N/100 mm (32 oz/inch) 98 N/100 mm (89,5 oz/inch) 96 N/100mm (87,5 oz/inch) 147 N/100 mm (134 oz/inch) 120 N/100mm (109 oz/inch) 182 N/100 mm (166 oz/inch) 142 N/100mm ( 130 oz/inch) > 200 N/100 mm (> 200 oz/inch) 35 hours 468,5 g
Performance PERFORMANCE PROPERTY CHEMICAL RESISTANCE Samples printed with the 510 ribbon and dwelled 24 hours prior to test. Testing consisted of 5 cycles of 10 minute immersions in the specified chemical reagent followed by 30 minute recovery periods. After final immersion, samples rubbed 10 times with cotton swab saturated with test fluid. For use in harsh enviroments use the 510 ribbon. White RPL / 510 Ribbon Black CHEMICAL REAGENT APPEARANCE OF THE PRINTING BEFORE RUBBING APPEARANCE OF THE PRINTING AFTER RUBBING RPL is designed to be rugged, with a good resistance to scratching, smearing and rubbing, and also to chemical threats like alcohols, diesel and oils. Three different colours are available; white, silver and yellow Isopropyl alcohol Methyl ethyl ketone Alcohol Mix* Gasoline Diesel Skydrol 500B-4 Mil 5606 Oil Lotoxane 5% sodium hydroxide 10% Sulphuric Acid Solution Deionized Water 10% Salt Water Solution n-hexane Iso-octane (2,2,4 Trimethylpentane) Ethanol ASTM#3 oil Acetone * Alcohol Mix is 50% ethanol, 30% methanol, and 20% water by volume Black RPL / 510 Ribbon White CHEMICAL REAGENT APPEARANCE OF THE PRINTING BEFORE RUBBING APPEARANCE OF THE PRINTING AFTER RUBBING Isopropyl alcohol Methyl ethyl ketone Alcohol Mix* Gasoline Diesel Skydrol 500B-4 Mil 5606 Oil Lotoxane 5% sodium hydroxide 10% Sulphuric Acid Solution Deionized Water 10% Salt Water Solution n-hexane Iso-octane Ethanol ASTM#3 oil Acetone * Alcohol Mix is 50% ethanol, 30% methanol, and 20% water by volume Storage history of similar products, support a customer usabililty expectation of at least two years from the date of receipt for this product as long as this product is stored in its original packaging in an environment below 21 C and 50% RH. We are confident that our product will perform well beyond this time frame. However, it remains the responsibility of the user to assess the risk of using such product. We encourage customers to develop functional testing protocols that will qualify a product's fitness for use, in their actual application. Trademarks: Polyken is a trademark of Testing Machines Inc. Skydrol is a registered trademark of the Monsanto Company ASTM: American Society for Testing and Materials (U.S.A.) S. I.: International System of Units Note: All values shown are averages and should not be used for specification purposes. 2003 Siegrist-Orel Limited. All rights reserved. The Siegrist-Orel logo is a registered trademark of Siegrist-Orel Limited. Other products and brand names may be trademarks of their respective owners. The information on this datasheet is believed to be correct at the time of publishing. Specifications given in this publication are subject to change without notice.
R RPL labels comes on a roll for itag Marking System printers and other thermal printers RPL Labels available to be printed with itag MArking System and other thermal transfer printers Order Number Width (A mm) Height (B mm) Colour PC/Roll Format Layout RPL-270-080-YW-S 27.00 8.00 Yellow 2500 R 0 RPL-270-080-WE-S 27.00 8.00 White 2500 R 0 RPL-270-080-SV-S 27.00 8.00 Silver 2500 R 0 Format RPL-270-125-YW-S 27.00 12.50 Yellow 2000 R 0 RPL-270-125-WE-S 27.00 12.50 White 2000 R 0 RPL-270-125-SV-S 27.00 12.50 Silver 2000 R 0 RPL-450-150-YW-S 45.00 15.00 Yellow 1500 R 0 RPL-450-150-WE-S 45.00 15.00 White 1500 R 0 RPL-450-150-SV-S 45.00 15.00 Silver 1500 R 0 R RPL-690-190-YW-S 69.00 19.00 Yellow 1200 R 0 RPL-690-190-WE-S 69.00 19.00 White 1200 R 0 RPL-690-190-SV-S 69.00 19.00 Silver 1200 R 0 RPL-1000-500-YW-S 100.00 50.00 Yellow 500 R 0 RPL-1000-500-WE-S 100.00 50.00 White 500 R 0 RPL-1000-500-SV-S 100.00 50.00 Silver 500 R 0 B 0 A Recommended Ribbons to be used. Other colours on request Ref Code Order Code Width Length Colour Core Size B1-510 TTR-040-300-BK-510 40mm 300 Meter Black 1 Inch B2-510 TTR-083-300-BK-510 83mm 300 Meter Black 1 Inch B3-510 TTR-110-300-BK-510 110mm 300 Meter Black 1 Inch