MOBILE 4 AUGER MIXER OWNER S MANUAL

MOBILE 4 AUGER MIXER OWNER S MANUAL Transcanadian Highway, Exit 170 230 Industriel Blvd, St-Germain Quebec, Canada J0C-1K0 Tel.: (819)395-4282 Fax : (819)395-2030 www.valmetal.com 1997/06 info@valmetal.com

TABLE OF CONTENTS FOREWORD... 2 IDENTIFICATION... 2 WARRANTY... 2 SAFETY PRECAUTIONS... 3 WARNINGS ON MIXER... 4 OPERATION INSTRUCTIONS... 5 BREAK-IN... 5 FILLING ORDER RECOMMENDATION :... 5 MAINTENANCE... 6 SPECIFICATIONS... 7 LIMITED WARRANTY... 8 PARTS MANUAL... 9 1

FOREWORD This manual describes the installation, operation and maintenance of the Valmetal Mobile 4 auger mixer. Be sure to read it carefully before operating the machine or providing maintenance for it in order to obtain a thorough knowledge of efficient and safe procedures. IDENTIFICATION A name plate riveted to the front of the gear oil bath bears specification and serial numbers of the unit. Refer to these numbers when ordering parts. Serial number : Model number : WARRANTY This piece of equipment is covered by warranty. Your dealer will explain the warranty agreement and will complete the delivery and warranty registration form. NOTE: The warranty is valid only if both dealer and customer or their representatives have completed and signed the warranty registration form, and that the completed form is received by VALMETAL within 15 days from the date of installation. SAFETY ALERT SYMBOL Pay special attention to this safety alert symbol, it indicates an important safety message. For your protection, we urge you to read all safety messages found in the manual and on safety signs adhered to the machine. 2

SAFETY PRECAUTIONS - Keep ALL guards in place. - DO NOT attempt to clean, oil or adjust machine while in operation. - Keep hands, feet and clothing AWAY from power driven parts. OPERATE EQUIPMENT SAFELY Do not allow anyone to operate, make adjustment or lubricate before reading and understanding this manual. Do not allow children or unauthorized personnel to operate the mixer.. Leave all guards, shields and safety devices in place. Never allow anyone near mixer while operating. Keep alert when operating equipment. Should any damage to equipment occur, shut off and lock out power immediately, make necessary inspection and repairs before restarting and operating. Never leave a machine running unattended. Failure to heed warnings may result in personal injury or death. Be sure area is clear before operating mixer. PRACTICE SAFE MAINTENANCE Do not allow anyone to make adjustment or lubricate before reading and understanding this manual. Disconnect PTO shaft from tractor before making adjustments or maintenance. Stop tractor motor and keep key with you Disconnect all hydraulic connectors from mixer. Keep all safety signs clean and readable. Failure to heed warnings may result in personal injury or death. Make certain all moving parts have stopped before making adjustments or leaving equipment. 3

WARNINGS ON MIXER 4

OPERATION INSTRUCTIONS 1-Before loading the mixer be sure the discharge door is closed and the mixing bin is free from foreign objects. 2-Remove tramp metal objets from magnet. DANGER NEVER ATTEMPT TO FREE JAMMED OR BINDING FEED WHILE MIXER IS RUNNING, YOU WILL BE CAUGHT IN THE AUGERS. STOP TRACTOR MOTOR AND KEEP KEY WITH YOU, DISCONNECT PTO SHAFT, THEN, FREE MIXTURE. BREAK-IN Although there are no operational restrictions on the mixer when operating for the first time, it is recommended that the following mechanical items be checked : After operating for the first hour : 1-Check and retorque ALL bolts and nuts if necessary, pay special attention to bearings amd sprockets set screws. 2-Verify roller chains alignment. After operating for 10 hours : Check tension and alignment roller chains, adjust as required. FILLING ORDER RECOMMENDATION : It is recommended to put corn silage or hight moisture corn before gradually put chunks of dry hay (hay must be of good quality). 5

MAINTENANCE WARNING : Always stop tractor motor, keep key with you and disconnect PTO shaft before making adjustments or maintenance. MONTHLY : LUBRICATION: 1-Grease sealed bearings every 40 hours of operation (wipe grease fitting with a clean cloth before greasing, to avoid injecting dirt and grit). NOTE : Over greasing can damage bearing seals. A damaged seal will lead to early bearing failure. NOTE : Replace worn grease fittings that will not hold the gun and fitting that will not take grease.. 2-Check the level of the oil bath. Thebottom part of the lowest sprockets and chains should soak in oil. If necessary add SAE 80-90 oil. 3-Check the oil level of the gear box. If necessary add S-75W-90 synthetic oil. NOTE FOR GEAR BOX : First oil change should be made after the first 100 hours of operation. Following oil change should be made every 2000 hours of operation or once a year. DRIVE CHAINS ADJUSTMENT : Check drive chains tension.. To adjust the chain tension : 1-Loosen nut retaining idler sprocket. 2-Slide idler sprocket toward chain to tighten or away from chain to loosen. 3-Tighten nut when chain is properly adjusted. DRIVE CHAINS ALIGNMENT : All roller chains must be in proper alignment at all times.. Misalignment indications are : excessive wear on one side of the sprocket teeth or side bar breakage. 6

SPECIFICATIONS MOBILE MODELS MODEL 270 325 375 450 Mixing capacity (cu. ft.) 270 325 375 450 Overall length (in.) 185½ 212½ 213 237 Tires overall width (in.) 90 92 98 98 Closed conveyor overall width (in.) 97 98 101 101 Opened conveyor overall width (in.) 101 102 115 115 Overall height (in.) 95 101 105 105 Mixing box size (in.) 84 X 120 84 X 144 84 X 144 84 X 168 Mixing box sides tickness (in.) 10 Gage 10 Gage 3/16 3/16 Mixing box ends tickness (in.) 3/16 3/16 3/16 3/16 Mixing box bottom tickness (in.) 3/8 3/8 3/8 3/8 Bottom auger -diameter (in.) 20 20 24 24 -flighting tickness (in.) 1/2 1/2 5/8 5/8 -tube (in.) 6 5/8 X.432 6 5/8 X.432 8 5/8 X.5 8 5/8 X.5 Top auger -diameter (in.) 20 20 24 24 - flighting tickness (in.) 3/8 3/8 3/8 3/8 -tube (in.) 4 ½ X.337 4 ½ X.337 6 5/8 X.432 6 5/8 X.432 Drive bottom shaft diameter (in.) 3 3 3½ 3½ Drive top shaft diameter (in.) 2½ 2½ 3 3 Roller chains 100-120 100-120 100-140 100-140 Approximate weight (lbs) 8100 9 700 11 100 12 600 Discharge opening size (in.) 32 X 20 32 X 20 32 X 20 32 X 20 Tires 16.5L16.1 10 ply 21.5L16.1 14 ply 21.5L16.1 14 ply 21.5L16.1 14 ply Transmission Planetary Planetary Planetary Planetary Weight bar 4 points 4 points 4 points 4 points Because VALMETAL Inc. in constantly improving products, we reserve the right to change design and/or specifications without notice. 7

LIMITED WARRANTY BASIC WARRANTY AND REMEDIES All VALMETAL products are warranted against defects in workmanship and materials for one year from date of delivery to the first purchaser. The warranty repair period for equipment used for commercial or rental purposes is limited to 90 days from date of delivery to the first retail purchaser. VALMETAL will repair or replace, free of charge, at its option, F.O.B. factory, freight prepaid, any parts proved defective in workmanship or materials. It is agreed that such replacement or repair is the exclusive remedy available from Valmetal, should any of Valmetal s products or parts prove defective. Valmetal will not be responsible for freight and labor charges involved for removing and replacing defective parts. EXCEPTIONS FROM THIS WARRANTY This warranty covers equipments under normal use and service, does not cover conditions resulting from misuse, negligence, alteration, accident or lack of performance of required maintenance. Replacement of maintenance items such as belts, spout liners, digger knives, blades, etc... are not covered. EXCEPTIONS FROM THE WARRANTY Motors are warranted directly by the motor manufacturer only and not by Valmetal. LIMITATION OF LIABILITY This warranty is in lieu of all other warranties, express or implied, written or oral. No employee, agent, dealer or any other person is autorized to give any warranties on behalf of Valmetal, nor to assume for Valmetal any other liability in connection with any its products. IN NO EVENT SHALL THE OWNER BE ENTITLED TO RECOVER FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES SUCH AS, BUT NOT LIMITED TO, LOSS OF CROPS, LOSS OF PROFITS OR REVENUE, OTHER COMMERCIAL LOSSES, INCONVENIENCE OR COST OF RENTAL OR REPLACEMENT EQUIPMENT. AN ADDITION TO LIMITED WARRANTY FOR SILO UNLOADERS 880 MODEL ONLY In addition to the regular 1 year limited written warranty, any parts that are determined by Valmetal Inc. to be defective in material and workmanship under normal use and service, in the second and third year from date of delivery to the first retail purchaser, will be covered by this limited warranty. Valmetal liability under this warranty is for repair or replacement of parts only but not for such labor involved for removing and replacing defective parts. Replacement of maintenance items such as belts, spout liners, digger knives, blades, blower paddles, bearings, etc... are not covered. 8

MOBILE 4 AUGER MIXER PARTS MANUAL Transcanadian Highway, Exit 170 230 Industriel Blvd, St-Germain Quebec, Canada J0C-1K0 Tel.: (819)395-4282 1997/06 Fax: (819)395-2030 9

MIXING BOX ITEM MODEL PART # DESCRIPTION 1 270 38-200 270 cu.ft. Mixing box 325 38-300 325 cu.ft. Mixing box 375 38-400 375 cu.ft. Mixing box 450 38-500 450 cu.ft. Mixing box 2 38-001 Safety bar support 3 270 37-205 Safety bar 325/375 37-305 Safety bar 450 38-505 Safety bar 4 38-008 Plate 5 38-038 Door support 6 94-160 Door gasket 7 38-037 Right door 8 38-036 Left door 9 270/325 38-204 Observation ladder 375/450 38-404 Observation ladder 10 99-2023 Rubber door latch 11 94-120 1" NPT femalle plug 12 99-244 3/8" x 1" Carriage bolt 13 99-143 3/8" x 1" Hex. bolt 14 99-242 3/8" x 3/4" Carriage bolt 15 99-342 3/8" Washer 16 99-352 3/8" Lock washer 17 99-302 3/8" Nut

AUGER ITEM MODEL PART # DESCRIPTION 1 270 37-221 Lower left auger 325 37-321 Lower left auger 375 38-421 Lower left auger 450 38-521 Lower left auger 2 270 37-222 Lower right auger 325 37-322 Lower right auger 375 38-422 Lower right auger 450 38-522 Lower right auger 3 270 37-224 Upper left auger 325 37-324 Upper left auger 375 38-424 Upper left auger 450 38-524 Upper left auger 4 270 37-225 Upper right auger 325 37-325 Upper right auger 375 38-425 Upper right auger 450 38-525 Upper right auger 5 270 37-043 Flanged shaft 325 38-317 Flanged shaft 375/450 38-416 Flanged shaft 6 270 37-043 Flanged shaft 325 38-316 Flanged shaft 375/450 38-416 Flanged shaft 7 270 37-020 Flanged shaft 325 38-315 Flanged shaft 375/450 38-415 Flanged shaft ITEM MODEL PART # DESCRIPTION 8 270 37-023 Flanged shaft 325 38-315 Flanged shaft 375/450 38-415 Flanged shaft 9 270/325 37-019 Bearing shield 375/450 38-419 Bearing shield 10 270/325 37-022 Bearing shield 375/450 38-423 Bearing shield 11 270/325 40-UCF215-48 Lower auger bearing 375/450 40-UCF218-56 Lower auger bearing 12 270/325 40-UCF213-40 Upper auger bearing 375/450 40-UCF215-48 Upper auger bearing 13 270/325 37-148 Retainer 375/450 38-431 Retainer 14 270/325 37-147 Retainer 375/450 38-432 Retainer 15 99-209 5/8" X 2 1/4" Hex. bolt 16 99-208 5/8" X 2" Hex. bolt 17 99-206 5/8" X 1" Hex. bolt 18 99-354 5/8" Lock washer 19 99-307 5/8" Nut 20 37-149 Retainer

270/325 cu.ft. SIDE DOOR ITEM PART # DESCRIPTION 1 38-207 Hydraulic cylinder support 2 38-232 Hydraulic cylinder bracket 3 38-240 Pin 4 38-035 Side door 5 38-238 Door opening indicator 6 99-143 3/8" X 1" Hex. bolt 7 99-352 3/8" Lock washer 8 99-302 3/8" Nut 9 99-214 5/8" X 3 1/2" Hex. bolt 10 99-307 5/8" Nut 11 99-503 Spring 12 99-175 ½" X 1½" Hex. bolt 13 99-304 ½" Nut 14 96-20-CHV-20-1 Hydraulic cylinder 15 96-20-CHV-20-2 Pin 16 96-20-CHV-20-3 Lock pin 17 99-402 3/16" X 1 1/2" Cotter pin

375/450 cu.ft. SIDE DOOR ITEM PART # DESCRIPTION 1 38-407 Hydraulic cylinder support 2 38-232 Hydraulic cylinder bracket 3 38-240 Pin 4 38-035 Side door 5 38-338 Door opening indicator 6 99-143 3/8" X 1" Hex. bolt 7 99-352 3/8" Lock washer 8 99-302 3/8" Nut 9 99-214 5/8" X 3 1/2" Hex. bolt 10 99-307 5/8" Nut 11 99-503 Spring 12 99-175 ½" X 1½" Hex. bolt 13 99-304 ½" Nut 14 96-20-CHV-20-1 Hydraulic cylinder 15 96-20-CHV-20-2 Pin 16 96-20-CHV-20-3 Lock pin 17 99-402 3/16" X 1 1/2" Cotter pin

DISCHARGING CONVEYOR ITEM PART # DESCRIPTION 1 38-041 Frame 2 38-042 Polyethylene liner 3 38-056 Deflector 4 38-052 Drive shaft 5 38-054 Adjustable extension 6 38-053 Idler shaft 7 38-055 Paddle 8 38-049 Bearing bracket 9 38-050 Bearing adjustment plate 10 38-048 Bearing bracket 11 38-051 Motor bracket 12 38-043 Cylinder bracket 13 38-045 Access door 14 38-044 Hinge 15 38-046 Holding pin assembly 16 38-046-1 Holding pin 17 38-046-2 Handle 18 38-057 Deflector side (option) 19 38-058 Deflector bottom (option) 20 96-25-CHV-16-1 Hydraulic cylinder 21 96-25-CHV-16-2 Hydraulic cylinder pin 22 96-25-CHV-16-3 Hydraulic cylinder hair pin 23 60-662-54-AS-11-L Left conveyor chain 24 60-662-54-AS-11-R Right conveyor chain 25 99-232 5/16" X 3/4" Carriage bolt ITEM PART # DESCRIPTION 26 99-316 5/16" Nylon lock nut 27 99-369 1/4" X 1/4" X 2" Key 28 60-62C6-1.125 62C6 X 1.125" Sprocket 29 99-475 5/16" X 5/16" Set screw 30 40-1.125-1.375-.75 1 1/8" X 1 3/8" X 3/4" Oilite bearing 31 99-268 1/4" X 3/4" Flat head bolt 32 40-UCFL-206-18 UCFL-206-18 Bearing 33 99-265 1/2" X 1 1/2" Carriage bolt 34 99-318 1/2" Nylon lock nut 35 99-533 5/8" X 8" Threaded rod 36 99-307 5/8" Nut 37 99-367 1/4" X 1/4" X 1 1/4" Key 38 98-40B16-1.125 40B16 X 1.125" Chain coupling sprocket 39 01-36-1815 40B16 X 1" Chain coupling sprocket 40 98-4016 40-2R-16 Chain (including 1 connecting link) 41 50-151-2127-1 Hydraulic motor 42 50-151-2127-2 Woodruff Key (supplied with motor) 43 99-142 3/8" X 3/4" Hex. bolt 44 99-352 3/8" Lock washer 45 99-242 3/8" X 3/4" Carriage bolt 46 99-324 3/8" Flange nut 47 99-184 1/2" X 3 1/2" Hex. bolt 48 99-400 3/16" X 1" Cotter pin 49 99-510 Spring

270 cu.ft. DRIVE ASSEMBLY ITEM PART # DESCRIPTION 1 60-120B14-3.149 Sprocket 120B14 X 3.149" 2 99-481 5/8" X 5/8" Set scew 3 99-940 22mm X 14mm X 100mm Key 4 60-120B40-3 Sprocket 120B40 X 3" 5 99-387 3/4" X 2 15/16 Key 6 60-120-76.5 Chain #120 X 76½" 7 60-100B30-3 Sprocket 100B30 X 3" 8 99-386 3/4 " X 1 15/16" Key 9 60-100B36-2.5 Sprocket 100B36 X 2½" 10 99-480 1/2" X 1/2" Set screw 11 99-377 5/8" X 1 15/16" Key 12 60-IS-100A12-.75 Idler sprocket 100A12 X ¾" 13 60-100-147 Chain #100 X 147" 14 37-056 Chain guide 15 60-100-102 Chain #100 X 102" 16 38-239 Tension roller arm 17 38-227 UHMW roller 18 13C85-0029 Spring 19 99-515 Turn buckle 20 37-048 Right oil deflector support 21 37-050-A Right oil deflector 37-050-B Base for right oil deflector 22 37-047 Left oil deflector support 23 37-049-A Left oil deflector 37-049-B Base for left oil deflector 24 99-143 3/8" X 1" Hex. bolt 25 99-352 3/8" Lock washer 26 99-302 3/8" Nut 27 99-242 3/8" X 3/4" Carriage bolt 28 99-342 3/8" Washer 29 99-220 3/4" X 2 1/4" Hex. bolt 30 99-320 3/4" Nylon lock nut 31 99-223 3/4" X 3 1/2" Hex. bolt 32 99-305 3/4" Lock washer 33 99-305 3/4" Nut 34 99-222 3/4" X 2 1/2" Hex. bolt 35 99-174 1/2" X 1 1/4" Hex. bolt 36 99-353 1/2" Lock washer 37 99-304 1/2" Nut 38 38-239-1 Tension roller arm 39 37-364 Tightener

325/375/450 cu.ft. DRIVE ASSEMBLY ITEM MODEL PART # DESCRIPTION 1 325 60-120B22-3.937 Sprocket 120B22 X 3.937" 375/450 60-140B16-3.937 Sprocket 140B16 X 3.937" 2 99-483 3/4" X 3/4" Set scew 3 99-943 28mm X 16mm X 200mm Key 4 325 60-120B40-3 Sprocket 120B40 X 3" 375/450 60-140B40-3.5 Sprocket 140B40 X 3½" 5 325 99-384 3/4" X 2 7/16" Key 375/450 99-383 7/8" X 2 7/16" Key 6 325 60-120-87 Chain #120 X 87" 375/450 60-140-94.5 Chain #140 X 94 1/2" 7 325 60-100B30-3 Sprocket 100B30 X 3" 375/450 60-100B30-3.5 Sprocket 100B30 X 3½" 8 325 99-386 3/4 " X 1 15/16" Key 375/450 99-389 7/8" X 1 15/16" Key 9 325 60-100B36-2.5 Sprocket 100B36 X 2½" 375/450 60-100B36-3 Sprocket 100B36 X 3" 10 99-481 5/8" X 5/8" Set screw 11 325 99-377 5/8" X 1 15/16" Key 375/450 99-386 3/4" X 1 15/16" Key 12 60-IS-100A12-.75 Idler sprocket 100A12 X ¾" 13 325 60-100-147 Chain #100 X 147" 375/450 60-100-150 Chain #100 X 150" 14 38-428 Chain guide 15 325 60-100-99.5 Chain #100 X 99½" 375/450 60-100-106.25 Chain #100 X 106¼" ITEM MODEL PART # DESCRIPTION 16 38-239 Tension roller arm 17 38-227 UHMW roller 18 13C85-0029 Spring 19 99-515 Turn buckle 20 38-233 Right oil deflector support 21 38-228 Right oil deflector 22 37-047 Left oil deflector support 23 37-049 Left oil deflector 24 99-143 3/8" X 1" Hex. bolt 25 99-352 3/8" Lock washer 26 99-302 3/8" Nut 27 99-242 3/8" X 3/4" Carriage bolt 28 99-342 3/8" Washer 29 99-220 3/4" X 2 1/4" Hex. bolt 30 99-320 3/4" Nylon lock nut 31 99-223 3/4" X 3 1/2" Hex. bolt 32 99-305 3/4" Lock washer 33 99-305 3/4" Nut 34 99-222 3/4" X 2 1/2" Hex. bolt 35 99-174 1/2" X 1 1/4" Hex. bolt 36 99-353 1/2" Lock washer 37 99-304 1/2" Nut

TRAILER ITEM MODEL PART # DESCRIPTION 1 270 38-226 Frame for 270 cu.ft 325 38-326 Frame for 325 cu.ft. 375 38-426 Frame for 375 cu.ft 450 38-526 Frame for 450 cu.ft 2 38-006 Tow bracket 3 38-007 Tow bracket pin 4 99-346 1" Washer 5 99-402 3/16" X 1½" Cotter pin 6 99-DG706 Jack 7 99-961 Weight bar 8 99-174 1/2" X 1 1/4" Hex. bolt 9 99-353 1/2" Lock washer 10 99-304 1/2" Nut 11 99-173 1/2" X 1" Hex. bolt 12 270 95-16.5L16.1-10 16.5L16.1 10 Ply tires 325/375/450 95-21.5L16.1-14 21.5L16.1 14 Ply tires 13 270 95-W11C16.1 W11C16.1 Wheel 325/375/450 95-W18C16.1 W18C16.1 Wheel 14 99-314 5/8"-18UNF WB-19 Nut 15 270 38-H8001 8M Hub 325/375/450 38-H10000 10M Hub 16 270 40-LM506810 LM506810 Inside cup 325/375/450 40-LM28921 LM28921 Inside cup 17 270 40-LM506849 LM506849 Inside bearing 325/375/450 40-LM28995 LM28995 Inside bearing 18 270 40-LM501310 LM501310 Outside cup 325/375/450 40-4T25520 4T25520 Outside cup 19 270 40-LM501349 LM501349 Outside bearing 325/375/450 40-4T25581 4T25581 Outside bearing 20 270 99-431 1" Washer 325/375/450 99-432 1¼" Washer 21 270 99-333 1"-14 UNF Hex. slotted nut 325/375/450 99-334 1¼"-UNF Hex. slotted nut 22 270 99-403 3/16" X 2" Cotter pin 325/375/450 99-405 1/4" X 2 1/2" Cotter pin 23 270 38-DC8000 DC-8000 Cap 325/375/450 38-DC10000 DC-10000 Cap 24 270 39-CR-27361 CR-27361 Seal 325/375/450 39-CR-29273 CR-29273 Seal

REDUCER DRIVE SHAFT AND P.T.O. ITEM MODEL PART # DESCRIPTION 1 270 45-PG702 Reducer 325/375/450 45-PG1602 Reducer 2 270 99-940 22mm x 14mm x 110mm Key 325/375/450 99-943 28mm x 16mm x 200mm Key 3 270 45-TL-T40 T40 1 3/8" Z.6 Universal joint with shearbolt 325/375/450 45-TL-T60 T60 1 3/8" Z.6 Universal joint with shearbolt 4 270 45-TL-T40-1 T40-1 3/8"-6 spline Yoke 325/375/450 45-TL-T60-1 T60-1 3/8"-6 spline Yoke 5 270 45-TL-T40-2 T40 Cross jounal set 325/375/450 45-TL-T60-2 T60 Cross jounal set 6 270 45-TL-T40-3 T40 1½" Yoke 325/375/450 45-TL-T60-3 T60 1½" Yoke 7 270 38-230 1½" Drive shaft 325/375 38-330 1½" Drive shaft 450 38-530 1½" Drive shaft 8 38-062 bearing housing ITEM MODEL PART # DESCRIPTION 9 38-033 Nylon bearing 10 38-031 Shield 11 40-UCF208-24 UCF208-24 Bearing 12 270 45-PTO-T40 T40 PTO shaft 325/375/450 45-PTO-T60 T60 PTO shaft 13 45-PTO-T40-10 Guard 45-PTO-T60-10 Guard 14 99-244 3/8" X 1" Carriage bolt 15 99-317 3/8" Nylon lock nut 16 99-128 5/16" X 1" Hex. bolt 17 99-316 5/16" Nylon lock nut 18 99-176 1/2" X 1 3/4" Hex. bolt 19 99-175 1/2" X 1 1/2" Hex. bolt 20 99-353 1/2" Lock washer 21 99-304 1/2" Nut

ACCESSORIES ITEM MODEL PART # DESCRIPTION 1 38-026 Hydraulic valve support tube (option) 2 38-025 Hydraulic valve support extension (option) 3 VS-3129 Locking handle (option) 4 270/325 38-231 Hydraulic valve support brace (option) 375/450 38-435 Hydraulic valve support brace (option) 5 38-029 Hydraulic 6 hose support 6 15-511-2 plate 7 38-028 Weight indicator support tube 8 38-061 Weight indicator back plate 9 38-040 Alarm light back plate (option) 10 38-030 Cable support 11 38-063 Cable support 12 38-039 Hydraulic 4 hoses support 13 38-060 Hydraulic 2 hose support 14 38-064 Hydraulic hose bracket 15 99-142 3/8" X 3/4" Hex. bolt 16 99-317 3/8" Nylon lock nut 17 99-173 1/2" X 1" Hex. bolt 18 99-318 1/2" Nylon lock nut 19 99-181 1/2" X 3" Hex. bolt