Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH)

Similar documents
Valve Timing, Adjust (Z 22 SE)

Timing Chain, Balancer Shaft, Replace (Z 22 SE)

Cylinder Head, Remove and Install (Z 22 SE)

Coolant Pump, Remove and Install (Z 22 SE)

Outside Rear View Mirror, Remove and Install

Pistons and Connecting Rods, Remove and Install

Crankshaft, Remove and Install (Engine Removed) (Z 22 SE)

3.6.1 Brake Lamp Switch

1 of 27 7/21/2015 3:33 PM

Exhaust Gas Recirculation Valve, Replace J S file://c:\program Files\cosids\DATA\TMP\ rtf.html. Remove

TECHNICAL INSTRUCTIONS FOR LIMITED SERVICE CAMPAIGN (LSC) A0N HV WATER PUMP REPLACEMENT MODEL YEAR PRIUS

18SP701Rev2 GHG14 Two-Filter Fuel System KM63 GEN2 DD15AT Engines High Pressure Fuel Feed Lines, Mounting Bracket and P-clips Service Kit

Removing and installing timing case cover. A. Engine

REMOVING CYLINDER HEAD COVER (VALVE COVER) - AS OF MY 2004 (CAYENNE TIP, CAYENNE MAN) > PRELIMINARY WORK > PRELIMINARY WORK


Oxygen sensor control,

Fuel supply system, servicing (vehicles with front wheel drive and 1.8 ltr. turbo or 2.8 ltr. engine)

AIR CLEANER GENERAL REMOVAL. 1CAUTION Do not run engine without filter element in place. Debris could be drawn into the engine causing damage.

Shown on engine 904.9

SERVICE MANUAL Gearbox - Allison AT545 - Gearbox Installation

18SP709Rev Page 1 of 8

Removal of the High Pressure Fuel Rail Feed Lines

Hydraulic Brakes and clutch on cars, vans, motorbikes etc work the same

2003 Nissan-Datsun Truck Frontier 4WD V6-3.3L (VG33E)

2/18/2017 Cylinder Head Assembly Service and Repair, Removal and Replacement: Cylinder Head

Checking ATF level; changing ATF Checking ATF level

for filling and bleeding hydraulic disk brake systems Instruction

Oxygen sensor control,

AR20.00-P-1142HA Drain/pour in coolant

ASNU Battleship MK2 Fitting Instructions

Shown on model Bolts 6 Oil lines 5 Screw 7 Adjusting screw Shown on model 209

18SP685 EPA07/10 DD15/16 High Pressure Fuel Feed Lines, Mounting Bracket, Vibration Dampers and P-clips Service Kit (P/N: A )

FUEL SUPPLY Click on the applicable bookmark to selected the required model year

10/20/ Ford E 250 Engine Mechanical > Engine, 4.6L and 5.4L > IN VEHICLE REPAIR > Intake Manifold 5.4L

International MaxxForce 7 6.4L Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service

Fuel supply system components, removing and installing

INTAKE MANIFOLD INSPECTION/REPLACEMENT

Special tools required:

Toothed belt, removing and installing

International DT L MaxxForce 9 9.3L Engine

Engine, removing and installing

Steering Gear Replacement

SCdefault. 900 Installation instructions

1999 F-150/250 Workshop Manual

18SP653 EPA04 and EPA98 MBE 4000 High Pressure Fuel Line and Transfer Tube Installation

ENGINE ACCESSORIES. D20DT Engine. PCV valve and oil separator. Turbo charger. EGR pipe (LH, Center, RH) Cooling fan clutch. Auto tensioner.

Specialist Components. SPi 5 Port EFI Kit

C6 RS6 Front Headlight Bulb Change Procedure

Cooling system components, removing and installing

Removing and installing cylinder head

1 Engine and peripherals

1 of 2 5/17/17, 1:22 PM

Removing and installing/replacing high-pressure pump (N47) (32 FRU)

AR47.20-P-7000TA REMOVE/INSTALL FUEL PUMP AND FUEL TANK SENSOR

57-1. Front door. Tools. Special tools and equipment. T Socket 3320/2 Bit insert for Socket T Assembly tool

M-9424-M50B 2012 Boss 302 Intake Manifold INSTALLATION INSTRUCTIONS

1983 BMW 320i. 1.8L 4-CYL 1983 Engines - 1.8L 4-Cylinder Engines - 1.8L 4-Cylinder

Motronic injection system,

Service Information. Oil change kit for ZF 8HP automatic transmission

GTFLOW EXTENSION MANIFOLD ASSEMBLY INSTRUCTIONS

2006 Volkswagen Phaeton

TECHNICAL BULLETIN Engine Vibration/Noise Above 1000 RPM Oil Pump Resonance Install Revised Oil Pump SERVICE DATE MODEL 2002 MY.

IN-VEHICLE REPAIR. Cylinder Head. Special Tool(s) Timing Tool, Crankshaft TDC (T97T-6303-A) or. Special Tool(s) equivalent

2011 Mercedes-Benz C350 Sport

Mercedes GLK250 ( ) 2.1L Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service

1999 E-Series Workshop Manual

Rear seat. Rear seat, removing and installing. - Using screwdriver -2-, carefully lift headrest guides -3- out of rear backrest -1-.

Hood. Hood, removing, installing and adjusting. Page 1 of 11

Cylinder Head Removal

2013 Kia Optima L4-2.0L Turbo

Direct Shift Gearbox (DSG) Mechatronic unit J743, removing and installing. - Loosen bolts - arrows - of oil pan - A - in diagonal sequence and remove.

FOLDING TOP HYDRAULIC CYLINDER HOSE IDENTIFICATION

ContiTech: Expert Tips for Changing Timing Belts

SCdefault. 900 Installation instructions

Steps 3 through 9 in this procedure describe making and using a cooling system bleed tool.

Mounting and Operating Instructions EB 8039 EN. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve. Type 3351 Pneumatic On/off Valve

Specialty Pond Sprayer

EGR Adapter Mercedes MBE L

2011 Mercury Grand Marquis LS

SERVICE INSTRUCTION PURGING OF LUBRICATION SYSTEM FOR ROTAX ENGINE TYPE 912 AND 914 (SERIES) SI SI Repeating symbols:

Brake Pressure Modulator Valve Assembly Replacement (LHD)

Bulb Renewal TOP ACCESS COVER

14-6. TSB Revision ENGINE COOLING ON-VEHICLE SERVICE

1 of 8 10/22/2015 3:08 PM

TECHNICAL INSTRUCTIONS FOR SAFETY RECALL ALE VALVE SPRING AND LASH ADJUSTER REPLACEMENT GS 350: IS 350:

3/13/ :32 AM. NOTICE: Do not disconnect the hose.

Removing and installing moulded headliner

Zoom and Print Options

Solar Thermal. Grant Solar Pump Station Installation & Servicing Instructions

Volkswagen New Beetle 1.8 Liter 4-Cyl. 5V Turbo OBD II Engine Mechanical 19 Engine-Cooling system (Page GR-19)

Turbocharger system. Note: Observe rules of cleanliness Page Charge air pressure control connection diagram Page 21-2.

Brake Upgrade Kit Fitting Instructions Bonneville America

Fuel and exhaust systems 4A 21

M H F150 4X4 Rear Lowering Kit

VW (Engine Code CJAA/CBEA) 2.0 Liter TDI Diesel EGR Cleaning Instructions. Always wear gloves and safety glasses when performing this service

2006 MINI Cooper ACCESSORIES & EQUIPMENT Audio, Navigation & Anti-Theft Systems - Repair Instructions - Cooper (1.6L) R50/W10 & Cooper S

Removal & Installation

J2 Remove sound insulation/knee guard 1 and side panel 2 on center console

AR01.30-P-5800PK Remove/install cylinder head

English. Fitting Instructions: America and Speedmaster A and A of 15

Transcription:

602854Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH) file://c:\program Files\cosids\DATA\TMP\00602854.rtf.html Page 1 of 2 Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH) Warning: Fuel escapes observe safety measures and national legislation. Remove 1. Disconnect battery Detach ground cable 2. Detach wiring harness plug, fuel filter heating (2) from fuel filter housing (3) release and disconnect 3. Detach wiring harness plug, water level sensor from fuel filter housing release and disconnect 4. Detach fuel feed line (5) open with KM- 796-A seal off with KM- 6015 5. Detach fuel feed line (4) open with KM- 796-A seal off with KM- 6015 6. Remove fuel filter housing (3) from crash box Install 7. Insert fuel filter housing (3) in crash box 8. Attach fuel feed line to pump (4) to fuel filter housing Remove KM-6320 9. Attach fuel feed line (5) to fuel filter housing Remove KM-6015 10. Attach wiring

602854Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH) file://c:\program Files\cosids\DATA\TMP\00602854.rtf.html Page 2 of 2 harness plug, fuel filter heating (2) to fuel filter housing (3) Connect and lock in place 11. Attach wiring harness plug, water level sensor to fuel filter housing Connect and lock in place 12. Connect battery Attach ground cable 13. Program volatile memories 14. If the fuel filter housing is not filled with fuel, bleed the fuel filter housing Turn ignition key to the "ignition on" position 3x and hold for min. 3 seconds each time Note: The preliminary conveying pump in the fuel tank runs at "ignition on" and fills the fuel filter housing in this way. Start engine If the engine stalls, repeat bleeding Inspect 15. Check fuel system for leaks with engine running

202887Fuel Filter Element, Replace (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202887.rtf.html Page 1 of 5 Fuel Filter Element, Replace (Diesel Engines) Warning: Fuel escapes observe safety measures and national legislation. Remove 1. Remove fuel filter housing see operation "Fuel Filter Housing, Remove and Install (Y 20 DTH, Y 22 DTR, Y 30 DT, LHD)" or "Fuel Filter Housing, Remove and Install (Y 20 DTH, Y 22 DTR, Y 30 DT, RHD)" or "Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH)" 2. Remove fuel filter element (2) Detach fuel filter housing cover (1) Unscrew central bolt remove out of fuel filter housing (3) and place in suitable container Note: collect escaping fuel and drain residual fuel out of fuel filter housing into suitable container 3. Z 19 DT, Z 19 DTH: Open fuel filter housing Clamp fuel filter housing with EN- 46784-020 (3) in vice Open cover of fuel filter housing (2) with EN-46784-010 (1)

202887Fuel Filter Element, Replace (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202887.rtf.html Page 2 of 5 4. Z 19 DT, Z 19 DTH: Detach screw cap (1) from fuel filter housing (5) EN-46784-20 clamped in vice Screw cap (1) Remove filter element with housing upper section (2, 3) Remove seal ring (4) Turn element (3) 50 anti-clockwise

202887Fuel Filter Element, Replace (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202887.rtf.html Page 3 of 5 Clean 5. Clean fuel filter housing lid and interior of fuel filter housing with a lint-free cloth. Assemble 6. Insert fuel filter element (5) into fuel filter housing (6) 7. Top up fuel filter housing (6) with new diesel fuel up to just under the edge 8. Assemble fuel filter housing use new gasket (4) for fuel filter housing cover (3) use new gasket for central bolt (2) Tighten central bolt (1) (6 Nm)

202887Fuel Filter Element, Replace (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202887.rtf.html Page 4 of 5 9. Z 19 DT, Z 19 DTH: Assemble fuel filter housing Insert new filter element (3) Renew seal ring (4) Turn element (3) 50 clockwise Note: Upper section of housing will fit only in one installation position. It is not possible to install it incorrectly. Attach screw cap (1) to fuel filter housing (5) Screw in screw cap (1) and tighten with EN-46784-10 (30 Nm)

202887Fuel Filter Element, Replace (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202887.rtf.html Page 5 of 5 Install 10. Install fuel filter housing see operation "Fuel Filter Housing, Remove and Install (Y 20 DTH, Y 22 DTR, Y 30 DT, LHD)" or "Fuel Filter Housing, Remove and Install (Y 20 DTH, Y 22 DTR, Y 30 DT, RHD)" or "Fuel Filter Housing, Remove and Install (Z 19 DT, Z 19 DTH)"

202891Fuel Filter, Drain Water (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202891.rtf.html Page 1 of 4 Fuel Filter, Drain Water (Diesel Engines) Warning: Fuel escapes observe safety measures and national legislation. Remove 1. Release central bolt (1) at fuel filter housing cover 2. Open drain bolt (1) 1 turn Collect water residue Important: Y 20 DTH, Y 22 DTR: Do not allow fuel filter housing to run dry as otherwise bleeding will be necessary - see operation "Fuel System, Bleed (Y 20 DTH, Y

202891Fuel Filter, Drain Water (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202891.rtf.html Page 2 of 4 22 DTR)". 3. Close drain bolt (1) as soon as diesel fuel escapes 4. Tighten central bolt (1) (6 Nm)

202891Fuel Filter, Drain Water (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202891.rtf.html Page 3 of 4 5. Z 19 DT, Z 19 DTH: Detach fuel filter housing (5) Disconnect fuel preheater wiring harness plug (1). Disconnect wiring harness plug for fuel temperature sensor (2) Remove fuel filter housing from crash box by carefully pulling it upwards Note: Fuel system remains closed. 6. Drain fuel filter Note: Do not shake fuel filter housing. Do not allow fuel filter housing to run empty. Collect fuel in a suitable container (3)

202891Fuel Filter, Drain Water (Diesel Engines) file://c:\program Files\cosids\DATA\TMP\00202891.rtf.html Page 4 of 4 Open drain bolt (4) approx. 1 turn as soon as diesel fuel flows out, close drain bolt Install 7. Z 19 DT, Z 19 DTH: Install fuel filter housing (5) Insert fuel filter housing in crash box and push down into guide Connect wiring harness plug of fuel pre-heater (1) Connect wiring harness plug of fuel temperature sensor (2)