CYLINDRS MDIUM DUTY, HVY DUTY, COMPCT ROUND, NON-ROTTING ROD, ND ISO/VDM SRIS CV ISO/VDM CYLINDRS INDX: Series CRS Pages - to -6 Series CTS Pages - to - Series, V, HV /", ", & -/8" ore Pages C- to C-7 Series V, HV -/8" ore Pages C-9 to C- -INDX SRIS CRS & CTS COMPCT CYLINDRS ir/oil Tandem Pages C- to C-5 ack-to-ack Pages C-6 to C-9 Three Position Pages C-0 to C- Spherical Mount Pages C- to C-7 Series, L, H, S /", -/8", & -/8" ore Pages C-8 to C- Series NPG, NHG, NG, NHG -/8" & -/8" ore Pages C- to C-5 ngineering Data Pages C-6 to C-8 Options Pages C-9 to C-7 Cleanroom Cylinder Page C-8 Series CV Pages D- to D-0 TOM THUM CYLINDRS CT-0 -i (800) 6-85 www.phdinc.com/products/cylinders
-INDX CYLINDRS COMPCT (SRIS CRS ND CTS) Compact size of the Series CRS and CTS Cylinders make them ideal for applications where cylinder length is critical. Optional shock pads extend cylinder life and minimize piston noise. The shock pad design adds no additional length to the cylinder. Series CTS Guide Shaft Cylinders excel in non-rotating cylinder applications where unit length is critical, and also perform as light duty slides where precise location is not required and side loading is limited. See sections and. MDIUM DUTY (SRIS, V, HV) /", ", -/8" SIZS Medium Duty Cylinders (/", ", and -/8" ore Sizes) are available in a wide range of Tom Thumb mounting styles and options. ll units are of tierod construction and repairable. vailable in single or double-acting. See section C. MDIUM DUTY (SRIS V, HV) -/8" SIZS The -/8" ore Medium Duty Cylinders have the same features as the smaller Tom Thumb Cylinders, but based on a more rugged design construction. See section C. IR/OIL TNDM (SRIS TD) Tandems are two cylinders coupled together through a common piston rod. The unit is air-powered while a hydraulic portion serves as a control media. The unit provides close, smooth control of piston rod speed if ordered with crossover tube (-X or -C option). See section C. NOT: Tandem unit may also be used to increase cylinder force when ordered without crossover option. CK-TO-CK (SRIS V, HV, ) The ack-to-ack Cylinder is for use where three or four rod positions are required. Two cylinders are attached back to back using common tierods. Different strokes on each cylinder give the capability of four positive stop positions. The ack-to-ack provides independent piston rod movement on each end of unit. See section C. THR POSITION (SRIS V, HV, ) Three Position Cylinder is used where three rod positions are required. Single rod extends to a positive midposition or to full extension. More than three positions may be obtained on request. See section C. -ii (800) 6-85 www.phdinc.com/products/cylinders CT-0
SPHRICL MOUNT (SRIS VS, HVS, S) Spherical Mount Cylinders provide a spherical mount on the cap end of a cylinder. Spherical rod ends may be ordered separately to get the spherical mounting on both ends. This mounting allows for misalignment as well as pivoting movement. See section C. HVY DUTY CYLINDRS (SRIS, L, H, S ) /", -/8", -/8" SIZS Heavy Duty Cylinders (/", -/8", and -/8" ore Sizes) feature cartridge-type bushings and hard chrome-plated alloy steel piston rods for high cycle and side load applications. vailable in a wide range of mounting styles and options. See section C. -INDX NON-ROTTING ROD CYLINDRS (SRIS NPG, NHG, NG, NHG) -/8" & -/8" SIZS Non-Rotating Rod Cylinders (-/8" & -/8" ore Sizes) incorporate an internally contained precision spline assembly and a hollow piston rod that eliminates the need for outriggers and external attachments. They can be specified in various mounting styles with a wide range of options available. ll Non-Rotating Rod Cylinders come standard with angular rod position adjustment for easy external assembly alignment. ll units are of tierod construction and are repairable. See section C. CLNROOM CYLINDRS (SRIS V, ) /",",-/8" SIZS Cleanroom option allows PHD Tom Thumb Cylinders to be used in Class 00 cleanroom applications. Compatible with all mounting styles and standard diameter rod. No change to existing catalog dimensions addition of vacuum port only. See section C. ISO/VDM CYLINDRS (SRIS CV) Series CV conform to both ISO 6 and VDM 56 specifications. Units are available in eight bore sizes from 0, 5, to 00 mm with stroke lengths from 5 to 000 mm. ll Series CV Cylinders feature the Hushcontrol dvantage. Hushcontrol provides superior control of piston rod and attached loads with low noise levels even at high cycle speeds. See section D. S TH PHD CLSSICS CTLOG FOR TH FOLLOWING PHD CYLINDRS: Magnetic Rodless Cylinder Series O Cylinder Series NG Cylinder-" & " ores Call -800-6-85 for your free catalog. CT-0 -iii (800) 6-85 www.phdinc.com/products/cylinders
COMPCT CYLINDRS SRIS CRS INDX: Ordering Data Page - enefits & Construction Page - Compact size is ideal for applications where length is critical. Dimensions Pages - and -5 ngineering Data Pages -6 Options Pages -7 to -0 ccessories Pages - to -5 Compact Cylinder pplications Page -6 CT-0 (800) 6-85 www.phdinc.com/crs -
ORDRING DT: SRIS CRS COMPCT CYLINDRS TO ORDR SPCIFY: Product, Series, Type, Design No., Mounting Style, ore Size, Stroke, and Options. PRODUCT C - Cylinder TYP S - Single Rod, Double cting (Standard) D - Double Rod, Double cting (See note.) MOUNTING STYL ll units have thru holes U - Universal (Standard) Thread and C'bore 8 Places, ach nd STNDRD STROK LNGTHS /" = Minimum stroke in /8" increments mm 6 0 5 0 50 6 IMPRIL STROK (CRx) MXIMUM STROK (in) -/ -/ -/ -/8 6-5/8 MXIMUM STROK WITH OPTIONS -I, -M, & -WP (in) -/ -/ -/ -/ -/8 6-/8 C R S U x / - M-T SRIS DSIGN NO. SIZ R - Compact - Imperial R R Round ore 5 - Metric mm in mm in NOTS: ) Options -I, -M, and -WP add /" [6.5 mm] to the overall cylinder length. ) Option -V may reduce cylinder lifespan due to fluorocarbon material. ) Option -Z may reduce cylinder lifespan due to stainless steel rod in place of chrome-plated stressproof. ) On double rod units, rear rod will receive same rod option as single rod. ccessories - see pages - to -5. 6 0 5 0 50 6 R I M WP F K_ T T T T55 T88 T99 V Z IMPRIL OPTIONS (CRx) - Shock Pads in both directions (No additional cylinder length) - Shock Pad on extension - Shock Pad on retraction - Magnetic piston for use with PHD Magnetoresistive Switches. See Note. - Magnetic piston for use with PHD Miniature Reed Switches. See Note. - Wide piston for extra rod support (Standard with -I or -M). See Note. - xtended length wrench flats - xtra Rod xtension in /8" increments. Length code example: K = /8", K = /8", etc. - Male Rod nd, fine thread - Male Rod nd, coarse thread - Female Rod nd, coarse thread (vailable on 0 mm through 6 mm sizes only) - Plain Rod nd with wrench flats - xtended Male Rod nd, fine thread - xtended Male Rod nd, coarse thread - Fluoro-lastomer Seals. See Note. - Corrosion resistant, stainless steel rod and electroless nickel plated retaining rings. See Note. R I! Options may affect unit length. See unit dimension and options pages for adders..7.6.79.98.6.57.97.8 0 90 80 56 96 7.75..86.760.7.98.05.8 M WP F K_ T T55 T99 V Z Go ack MTRIC STROK (CRx5) STNDRD STROK LNGTHS 5 mm = Minimum stroke in 5 mm increments mm 6 0 5 0 50 6 MXIMUM STROK [mm] 75 80 00 00 05 0 0 65 MXIMUM STROK WITH OPTIONS -I, -M, & -WP [mm] 70 75 95 95 00 05 05 60 MTRIC OPTIONS (CRx5) - Shock Pads in both directions (No additional cylinder length) - Shock Pad on extension - Shock Pad on retraction - Magnetic piston for use with PHD Magnetoresistive Switches. See Note. - Magnetic piston for use with PHD Miniature Reed Switches. See Note. - Wide piston for extra rod support (Standard with -I or -M). See Note. - xtended length wrench flats - xtra Rod xtension in 5 mm increments. Length code example: K5 = 5 mm, K5 = 5 mm, etc. - Male Rod nd - Plain Rod nd with wrench flats - xtended Male Rod nd - Fluoro-lastomer Seals. See Note. - Corrosion resistant, stainless steel rod and electroless nickel plated retaining rings. See Note. - (800) 6-85 www.phdinc.com/crs CT-0
COMPCT CYLINDRS: SRIS CRS NFITS The compact size of the Series CRS Cylinder makes it ideal for applications where cylinder length is critical. Series CRS Cylinders have been tested to 0 million cycles under normal conditions. Thru and threaded holes for easy cylinder mounting. Optional accessories provide additional mounting flexibility. Nitrile piston and rod seals for long life and low maintenance. Optional Fluoro-lastomer seals for greater fluid compatibility. Consult PHD for high temperature use. Field repairable for extended life. Optional shock pads extend cylinder life and minimize piston noise in applications where the piston contacts the head and/or cap. The shock pad design adds no additional length to the cylinder. vailable with two piston lengths. The standard piston provides the shortest possible units. The wide piston provides additional rod end stability and magnet capability for use with PHD Magnetoresistive and Reed Switches. Switches may be mounted on three sides of the cylinder for maximum flexibility (two sides for and 6 mm sizes) and provide a signal on extension and retraction with strokes as short as / inch [5 mm]. CONSTRUCTION Hard chrome-plated steel piston rod provides maximum wear resistance for long life. Hardcoated bore for extended cylinder life. Long life Nitrile piston and rod seals for low maintenance. ronze bushings are standard on mm through 0 mm, hardcoated aluminum bushings for 50 mm and 6 mm. CT-0 (800) 6-85 www.phdinc.com/crs -
DIMNSIONS: SRIS CRS COMPCT CYLINDRS mm and 6 mm C S XTND X G X R PORT RTRCT H CL 8X DRILL & C' FOR M SOCKT HD CP SCRW N THRD J THRD Ø K ROD L WRNCH FLT x.5 [.0] LONG X SWITCH MTG SLOT.57 [.0] 8X(N) F + STROK.57 [.0] + STROK DOUL ROD ONLY 0 mm through 0 mm C XTND X G X R PORT RTRCT H P D CL 8X DRILL & C' FOR M SOCKT HD CP SCRW N THRD X SWITCH MTG SLOT J THRD Ø K ROD L WRNCH FLT x.5 [.0] LONG.57 [.0] 8X(N) F + STROK STNDRD RR PORT LOCTION FOR mm ND 0 mm UNITS WITH LSS THN [5.0] STROK.57 [.0] + STROK DOUL ROD ONLY 50 mm and 6 mm C XTND X G X R PORT RTRCT H D CL 8X DRILL & C' FOR M SOCKT HD CP SCRW N THRD X SWITCH MTG SLOT J THRD Ø K ROD L WRNCH FLT x.5 [.0] LONG ) DIMNSIONS SHOWN IN [ ] R IN mm OR FOR MTRIC UNITS [CRx5] ) DSIGNTD CNTRLIN IS CNTRLIN OF CYLINDR ) UNLSS OTHRWIS DIMNSIOND, MOUNTING HOL PTTRNS R CNTRD ON DSIGNTD CYLINDR CNTRLIN ) /" [5 mm] MINIMUM STROK RQUIRD 5) OPTIONS -I, -M, ND -WP DD /" [6.5 mm] TO TH OVRLL LNGTH.57 [.0] 8X(N) F + STROK.57 [.0] + STROK DOUL ROD ONLY - (800) 6-85 www.phdinc.com/crs ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS CRS COMPCT CYLINDRS.7 [].60 [6].787 [0].98 [5].60 [].575 [0].969 [50].80 [6] FFCTIV R in [mm ] NON-ROD ND ROD ND.75.6 [.0] [8.0]..6 [0.0] [69.0].87.76 [.0] [.0].76.650 [90.0] [9.0].7.90 [80.0] [606.0].98.6 [56.0] [058.0].0.60 [96.0] [678.0].8.90 [7.0] [8.0].550 [.0].70 [8.0].000 [5.].00 [8.0].9 [.0].575 [0.0].969 [50.0].60 [60.0] C D.60 [.0].0 [.0].576.788 [0.0] [0.0].76.000 [.5] [5.].07.0 [5.0] [.0].6.0 [60.0] [.0].795.0 [7.0] [.0].66.0 [8.0] [6.].9 [.0].0 [8.0].76 [7.5].576 [0.0].870 [7.5].05 [56.0].598 [66.0].070 [78.0] LTTR DIMNSION. [8.75].88 [7.].66 [6.75].9 [0.0].97 [.6].88 [.] F.90 [.0].90 [.0].90 [.5].90 [.5].0 [6.0].0 [6.0].00 [.0].0 [6.0] F W/ OPTIONS -I, -M, -WP.5 [9.5].5 [9.5].70 [0.0].70 [0.0].7 [.5].7 [.5].550 [9.5].670 [.5] G.5 [8.5].5 [8.5].50 [9.0].50 [9.0].75 [9.5].60 [9.0].70 [.0] [.75] H.7 [.0].5 [.5].5 [.5].55 [.0].60 [5.5].78 [8.75].8 [.0].865 [.0] J THRD 8- x.50 [M x.7 x 6] 8- x.50 [M x.7 x 6] /-8 x.75 [M6 x.0 x 9] /-8 x.75 [M6 x.0 x 9] 5/6- x.70 [M8 x.5 x ] 5/6- x.70 [M8 x.5 x ] /8- x.56 [M0 x.5 x ] /8- x.56 [M0 x.5 x ].7 [].60 [6].787 [0].98 [5].60 [].575 [0].969 [50].80 [6] K.50 [6.5].50 [6.5].75 [9.5].75 [9.5].65 [5.9].65 [5.9] [9.0] [9.0] L.9 [5.5].9 [5.5]. [8.0]. [8.0] [.0] [.0].65 [6.0].65 [6.0] M #6 [M] #6 [M] #0 [M5] #0 [M5] #0 [M5] #0 [M5] / [M6] / [M6] LTTR DIMNSION N THRD 0- x.550 [M5 x.8 x.5] 0- x.550 [M5 x.8 x.5] /-0 x.875 [M6 x.0 x.5] /-0 x.875 [M6 x.0 x.5] /-0 x.875 [M6 x.0 x.5] /-0 x.875 [M6 x.0 x.5] 5/6-8 x.900 [M8 x.5 x.5] 5/6-8 x.900 [M8 x.5 x.5] Numbers in [ ] are in mm or for metric units [CRx5]..9 [.0].8 [6.5] P R 0- x.5 [M5 x.8 x ] 0- x.5 [M5 x.8 x ] 0- x.5 [M5 x.8 x ] 0- x.5 [M5 x.8 x ] /8 NPT [/8 SP] /8 NPT [/8 SP] /8 NPT [/8 SP] / NPT [/ SP] S.866 [.0].96 [.0] ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/crs -5
NGINRING DT: SRIS CRS COMPCT CYLINDRS mm in ROD DI. ROD DIRCTION FFCTIV R mm in mm in lb N 6.7.60.50.50 6.5 6.5 PUSH.75.5 6 PULL PUSH PULL.6..6 8 0 69.5 6 5.5 8 0.787.75 9.5 PULL.76 7.5 PUSH.87 9.5 5.98.75 PUSH.76 90 5 68 9.5 PULL.650 9 58.60.65 5.88 PUSH.7 80 5 PULL.90 606 9 8 0.575.65 5.88 PUSH.98 56 9 7 PULL.6 058 6 50.969 9.05 PUSH.0 96 6 7 PULL.60 678 5 6.80 9.05 PUSH.8 7 97 0 PULL.90 8 88 9 Note: Use pull forces for calculating double rod end performance. CYLINDR FORC TL CYLINDR FORC IN POUNDS FOR psi ND IN NWTONS FOR bar 0 /.8 0 /.76 60 /. 80 / 5.5 00 / 6.90 0 / 8.8 50 / 0.5 lb N lb N lb N lb N lb N lb N 7 0.5 7 6 7.5 78 9 6 7 5 7.5 0 5.5 56 5 67 9 8.5 55 8.5 8 5 9 7 66 7 08 0.5 7 6 70 9 6 7 0 9 75 9.5 87 9 0 9 7 9 7 58 60 7 5 5 67 0 0 8 68 5 0 57 5 0 5 6 0 6 7 76 8 9 06 508 6 6 9 7 5 65 89 78 7 98 50 75 00 5 555 50 665 87 8 8 67 56 5 75 9 8 50 67 78 7 7 50 56 69 95 866 00 9 00 66 9 99 8 58 6 70 97 876 6 095 5 8 8 08 0 5 65 65 57 0 0 6 56 69 08 96 60 57 89 90 76 9 860 90 90 87 79 8 9 580 579 75 76 78 6 7 5 56 9 95 57 659 99 SIZ mm 6 mm 0 mm 5 mm mm 0 mm 50 mm 6 mm CYLINDR WIGHT TL S WIGHT lb kg..05.7.08.5..6..8..60.7.78.5.95. DDR PR " [5 mm] OF STROK lb kg.085.0.0.05.5.07.6.07.6..0..0.8.8. PRSSUR RTINGS ll Series CRS Compact Cylinders have a maximum pressure rating of 50 psi [0 bar] air and are for pneumatic use only. RKWY The breakaway pressure is 0 psi [.7 bar] at zero load. TMPRTUR LIMITS - SLS Series CRS Cylinders are equipped with long life Nitrile seals suitable for use in temperatures ranging from -0 to +80 F [-8 to +8 C]. STROK TOLRNC Tolerance on the nominal stroke length is ± / inch [±.8 mm]. VLOCITY verage minimum velocity of unit is designed to be 0 in/sec [.5 m/sec] with zero load at 00 psi [7 bar]. LURICTION ll units are permanently lubricated at the factory and can be used with non-lubricated air. Seals are compatible with standard petroleum-based oil used for lubrication of air cylinders. LIF XPCTNCY Series CRS Cylinders have been tested to 0 million trouble-free cycles under normal conditions. Lubricated air may increase life of unit. Options -Z and -V may reduce life expectancy. MINTNNC s with most PHD products, these cylinders are field repairable. Rebuild kits, piston and rod assemblies, and main structural components are available as needed for extended service. PPLICTION The PHD Series CRS Cylinders are designed for use as a source of power and motion and not a load deceleration device. s with typical compact cylinders, the Series CRS Cylinder is not intended for applications where side loads or impact with attached loads are present. PHD recommends the use of external stops to ensure maximum cylinder life. See best application practices on page -6. SHOCK PD USG Optional shock pads are recommended for applications where the piston travels the full stroke length and contacts the head and/or cap (with no attached loads). The use of shock pads reduces noise and provides maximum cylinder life in these applications. See best application practices on page -6. -6 (800) 6-85 www.phdinc.com/crs CT-0
OPTIONS: SRIS CRS COMPCT CYLINDRS SHOCK PDS ON XTNSION ND RTRCTION SHOCK PD ON XTNSION R SHOCK PD ON RTRCTION Shock pads eliminate metal-to-metal contact and minimize piston impact. Shock pads are recommended for applications where the piston travels the full stroke length and contacts the head and/or cap (with no attached loads). The use of shock pads reduces noise and provides maximum cylinder life in these applications. SHOCK PD ON XTNSION SHOCK PD ON RTRCTION F XTNDD LNGTH WRNCH FLTS The design of a compact cylinder requires the length to be as short as possible. The standard wrench flat length is.5" [ mm]. The option -F provides wrench flats which allow standard wrench access. [mm] /6 0/5 /0 50/6 XTNDD WRNCH FLTS.00.00.90.90 [5.5] [5.5] [8.00] [8.00] ROD XTNSION.50 [6.5].50 [6.5]. [9.0]. [9.0] Numbers in [ ] are in mm or for metric units [CRx5]. K_ XTR ROD XTNSION xtra rod extension can be achieved by specifying the option -K followed by the length code. Length code example (for imperial CRx units) K = /8" of extra rod extension K = /8", etc. Length code example (for metric CRx5 units) K5 = 5 mm of extra rod extension K5 = 5 mm, etc..57" [ mm] of rod extension is standard. vailable in /8" [5 mm] increments only..57 [.0] STD XTNSION K_ XTR ROD XTNSION ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/crs -7
OPTIONS: SRIS CRS COMPCT CYLINDRS I MGNT FOR PHD MGNTORSISTIV SWITCHS This option equips the cylinder with a magnetic band on the piston for use with PHD Magnetoresistive Switches. These switches mount easily to the cylinder using T slots in the body. TYP M MGNT FOR PHD MINITUR RD SWITCHS This option equips the cylinder with a magnetic band on the piston for use with PHD Series 560 Miniature Reed Switches. These switches mount easily to the cylinder using T slots in the body. TYP WP WID PISTON FOR XTR ROD ND SUPPORT This option provides additional rod end stability. ll units with magnetic pistons will automatically receive a wide piston to accommodate the magnet. NOT: Options -I, -M, or -WP, add /" [6.5 mm] to the overall length of the cylinder. V FLUORO-LSTOMR SLS Fluoro-lastomer seals are compatible with certain fluids which degrade standard Nitrile seals. Seal compatibility should be checked with the fluid manufacturer for correct application. Consult PHD for high temperature use. [mm].00 [8.0] 6.00 [8.0] 0.00 [5.5] 5.50 [6.5].50 [6.5] 0.50 [6.5] 50.00 [8.0] 6.00 [8.0] Numbers in [ ] are in mm or for metric units [CRx5]. SWITCH MOUNTING TL MINIMUM STROK FOR XTND OR RTRCT MINIMUM STROK FOR TWO SWITCHS ON ON SID [mm], 6, 0 5,, 0 50, 6 C RD 5609--0 569-.50 [5] *.50 [5].50 [5] DC RD 560--0 56-.50 [5].50 [5].50 [5] MGNTO- RSISTIV 5605--0 5606--0 565-566-.50 [5].50 [5].50 [5] C RD 5609--0 569- [5] * [0].75 [5] DC RD 560--0 56-.65 [0] [0].75 [5] MGNTO- RSISTIV 5605--0 5606--0 565-566-.5 [0].5 [0].000 [5] XTND RTRCT *C Reed Switch may overhang on rod end of units when sensing extend end of stroke for all strokes (.087" [ mm] on 5 mm,.05" [ mm] on mm,.00" [ mm] on 0 mm). This may interfere with J brackets. -8 (800) 6-85 www.phdinc.com/crs ll dimensions are reference only unless specifically toleranced. CT-0
OPTIONS: SRIS CRS COMPCT CYLINDRS T ML ROD ND, FIN THRD T ML ROD ND, CORS THRD These options provide a studded male rod end in place of the standard female threaded rod end. The metric CRS is available with coarse threads only. See page -5 for specifications of standard rod ends. + -.060.000 + -.50 0.00 -T FIN [mm] THRD /6 N/ 0/5 /-8 /0 5/6-50/6 /8-8- /-0 5/6-8 /8-6 -T CORS THRD [M x.7] [M6 x.0] [M8 x.5].5.580.65.80 [0.0] [6.0] [9.0] [M0 x.5] [.0] NOTS: ) Numbers in [ ] are in mm or for metric units [CRx5]. ) On double rod units, rear rod receives same rod end as single rod. THRD DOUL ROD UNITS ONLY T FML ROD ND, CORS THRD This option provides a female coarse thread rod end. This option can be applied to imperial 0 mm through 6 mm bore units. The imperial mm and 6 mm bore units have an 8- coarse thread as standard. See page -5 for standard thread sizes. The metric mm through 6 mm bore units have coarse threads as standard. [mm] /6 0/5 /0 50/6 -T CORS THRD (STD) /-0 5/6-8 /8-6 (STD).75.70.56 On double rod units, rear rod receives same rod end as single rod. THRD x DP T55 PLIN ROD ND This option provides a plain rod end with wrench flats. Standard PHD Compact Cylinders are supplied with a female rod end. On double rod units, rear rod receives same rod end as single rod. DOUL ROD UNITS ONLY ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/crs -9
OPTIONS & CCSSORIS: SRIS CRS COMPCT CYLINDRS T88 XTNDD ML ROD ND, FIN THRD T99 XTNDD ML ROD ND, CORS THRD These options provide a studded male rod end with extended length threads. Metric CRS units are available with coarse threads only. See page -9 for standard length male rod end options. +.060 -.000 +.00 -.50 [mm] /6 0/5 /0 50/6 -T88 FIN THRD N/ /-8 5/6- /8-8- /-0 5/6-8 /8-6 -T99 CORS THRD [M x.7] [M6 x.0] [M8 x.5] [M0 x.5].700.00.50.690 [9.0] [.0] [.0] [7.0] NOTS: ) Numbers in [ ] are in mm or for metric units [CRx5]. ) On double rod units, rear rod receives same rod end as single rod. THRD DOUL ROD UNITS ONLY Z CORROSION RSISTNT lectroless nickel plating is applied to the retaining rings and a stainless steel piston rod is supplied. Male rod ends are not plated when this option is specified. This option may reduce seal life. HXGONL NUT KIT Nut kits include a hexagonal nut for use with male studded rod ends. ll male rod end options are shipped without hexagonal nuts. D THRD C DIMNSIONS [mm] C /6 0/5 /0 50/6.5..56.85.87.577.650.5.57.87.5 [7.0] [0.0] [.0] [7.0] [7.7] [.0] [.] [8.9] [.] [.] [.0] [5.0] D THRD FIN N/ [N/] /-8 [N/] 5/6- [N/] /8- [N/] Numbers in [ ] are in mm or for metric units [CRx5]. KIT NO. FIN N/ [N/] 97-05 [N/] 97-07 [N/] 97-09 [N/] D THRD CORS 8- [M x.7] /-0 [M6 x.0] 5/6-8 [M8 x.5] /8-6 [M0 x.5] KIT NO. CORS 97-09 [0-05] 97-0 [0-0] 97-06 [0-00] 97-08 [0-05] -0 (800) 6-85 www.phdinc.com/crs ll dimensions are reference only unless specifically toleranced. CT-0
CCSSORIS: SRIS CRS COMPCT CYLINDRS CYLINDR PIVOT X H SHCS (SUPPLID IN KIT) F RD G HOL FOR Ø J mm PIN C X H SHCS (SUPPLID IN KIT) G HOL FOR Ø J mm PIN F C D / D RONZ USHING - 5 mm D -6 mm [mm] 6 0 5 0 50 6.650 [6.5].650 [6.5].790 [0.0].790 [0.0].065 [7.0].065 [7.0].60 [7.0].60 [7.0].68 [6.5].678 [7.5] [9.0].800 [0.5].95 [.0].05 [8.0].00 [.0] [8.0] C.905 [.0].905 [.0].50 [.75].50 [.75].56 [.5].56 [.5].66 [6.5].66 [6.5] D.06 [7.0].06 [7.0] [8.0] [8.0].870 [8.0].0 [56.0].600 [66.0].000 [76.0] DIMNSIONS.76 [.0].56 [5.0] [8.0].600 [.0].870 [8.0].0 [56.0].600 [66.0].000 [76.0] F.8 [7.5].8 [7.5].55 [9.0].55 [9.0].80 [.0].80 [.0].000 [5.5].000 [5.5] Numbers in [ ] are in mm or for metric units [CRx5]. G.9 [.0].9 [.0].5 [9.0].5 [9.0].75 [7.5].75 [7.5].970 [50.0].970 [50.0] H 0- [M5 x.8] 0- [M5 x.8] /-0 [M6 x.0] /-0 [M6 x.0] /-0 [M6 x.0] /-0 [M6 x.0] 5/6-8 [M8 x.5] 5/6-8 [M8 x.5] J.97 [5.0].97 [5.0].7 [6.0].7 [6.0].9 [0.0].9 [0.0].7 [.0].7 [.0] KIT NO. IMPRIL CRx 6078-6079- 6080-608- 608-608- 608-6085- KIT NO. MTRIC CRx5 6086-6087- 6088-6089- 6090-609- 609-609- NOTS: ) -5 mm IS RIT ZINC PLTD STL ) -6 mm IS NODIZD LUMINUM WITH LURICTD RONZ USHINGS ) FULCRUM PIN NOT INCLUDD (S FULCRUM PIN KITS TO PURCHS) S PIVOT X THRU HOL FOR J SHCS X RONZ USHING X THRU HOL FOR J SHCS X RONZ USHING M L N K M L HOL FOR Ø F mm PIN (PIN SUPPLID WITH KIT) H HOL FOR Ø F mm PIN (PIN SUPPLID WITH KIT) H [mm] /6 0/5 /0 50/6.865 [.0].000 [5.5].75 [5.0].890 [8.0].5 [9.0].55 [.5].800 [6.0].65 [60.0] C.650 [6.5].790 [0.0].065 [7.0].60 [7.0] **G D Numbers in [ ] are in mm or for metric units [CRx5]. C * PHD CYLINDR PIVOT NOT INCLUDD - 5 mm -6 mm D.90 [.5].60 [6.0].600 [5.].755 [9.].0 [5.6].60 [6.5].00 [0.].505 [.0] F.97 [5.0].7 [6.0].9 [0.0].7 [.0] DIMNSIONS G H.060.75 [.5] [9.5].00.5 [.0] [.0].56.50 [.0] [.0].6.709 [6.0] [8.0] J #0 [M5] / [M6] / [M6] 5/6 [M8] K N/ N/.695 [.0].65 [57.5] L.905 [.0].50 [.75].50 [.5].650 [6.5] M.00 [.0].70 [.0].90 [8.0].970 [50.0] N N/ N/ D.65 [55.0].85 [7.0] * **G C KIT: CRxx, CRx5x IMPRIL/MTRIC 609-6095- 6096-6097- PHD CYLINDR PIVOT NOT INCLUDD NOTS: ) -5 mm IS RIT ZINC PLTD STL WITH LURICTD RONZ USHINGS ) -6 mm IS NODIZD LUMINUM WITH LURICTD RONZ USHINGS ) FULCRUM PIN INCLUDD. DOS NOT INCLUD CYLINDR PIVOT. ) * IS TO CNTR OF PIVOT PIN 5) **G IS FROM CNTR OF PIVOT PIN TO CNTR OF FIRST MOUNTING HOL ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/crs -
CCSSORIS: SRIS CRS COMPCT CYLINDRS F F MOUNTS Plated steel for use where front or rear mounting is not feasible. rackets are narrow allowing units to be used where space to the side of the cylinder is limited. NOT: rackets may be mounted in different configurations. ach kit includes bracket and cylinder mounting hardware. kits recommended per unit! THRU HOL X G OLT H X D RCOMMNDD ROD XTNSION TO CLR SHCS FOR UNITS WITH STNDRD FLTS (S -K_ OPTION PG -7 FOR PROPR CLLOUT) *MINIMUM STROK RQUIRD FOR LGS OF OTH RCKTS TO UNDR UNIT (SUTRCT.50 [5.0] FROM P FOR MGNTIC UNITS) H P* X F X J SOCKT HD CP SCRW (SUPPLID IN KIT) K LONG LG X C X NOT: THIS VIW WITH LONG LG S MOUNTING SURFC SHORT LG X M X L X N NOT: THIS VIW WITH SHORT LG S MOUNTING SURFC [mm] 6 0 5 0 50 6.87 [.0].95 [.0].000 [5.5].00 [8.0].80 [.5].5 [6.0] [.5].00 [5.0].55 [.0]. 589 [5.0].680 [7.5].690 [7.5].70 [8.5].807 [0.5].905 [.0].985 [5.0] C.770 [9.50].850 [.50].90 [.00].950 [.00].05 [6.5].80 [0.00].0 [6.00].50 [8.50] D.550 [.0].70 [8.0].000 [5.5].00 [8.0].0 [.0].575 [0.0].970 [50.0].60 [60.0].950 [.00].0 [8.5].560 [9.75].60 [.00].890 [8.00].05 [56.00].600 [66.00].070 [78.00] F. [8.0].0 [8.5].80 [9.5].95 [0.0]. [.0].9 [.0]. 55 [.5].575 [.5] Numbers in [ ] are in mm or for metric units [CRx5]. DIMNSIONS G H #0.50 [M5] [5.0] #0.50 [M5] / [M6] / [M6] / [M6] / [M6] [0.0].75 [0.0].75 [0.0].75 [0.0].75 J 0- [M5 x.8] 0- [M5 x.8] /-0 [M6 x.0] /-0 [M6 x.0] /-0 [M6 x.0] /-0 [M6 x.0] 5/6-8 K.986 [5.0].06 [7.0].80 [0.0].0 [.5].00 [5.5].595 [0.5] [0.0] 5/6.885 [M8] [5.0] [M8 x.5] [8.0] 5/6 5/6-8.65 [M8] [5.0] [M8 x.5] [55.0] L. [.5].75 [.0] [.75].550 [.0].60 [5.5].65 [6.0].765 [9.5].80 [.0] M.660 [7.0].70 [8.5].760 [9.].85 [.0].95 [.5].975 [5.0].50 [.0].5 [.7] N.6 [8.5].55 [9.0].80 [9.7].5 [0.5].6 [.].6 [.].556 [.].580 [.7] P /8 [0.0] /8 [0.0] / [5.0] / [5.0] 5/8 [0.0] 5/8 [0.0] 7/8 [5.0] 7/8 [5.0] IMPRIL CRx KIT NO. MTRIC CRx5 5890-600- 58905-600- 58906-600- 58907-6005- 58908-6006- 58909-6007- 5890-6008- 589-6009- - (800) 6-85 www.phdinc.com/crs ll dimensions are reference only unless specifically toleranced. CT-0
CCSSORIS: SRIS CRS COMPCT CYLINDRS J J MOUNTS Plated steel for use where height is critical, but room is available to sides of unit. Note: rackets may be mounted in different configurations. Kit includes brackets and cylinder mounting hardware. THRU HOL X M SHCS K L P H J G RCOMMNDD ROD XTNSION TO CLR SHCS FOR UNITS WITH STNDRD FLTS (S -K_ OPTION PG -7 FOR PROPR CLLOUT) X N MINIMUM STROK RQUIRD FOR LGS OF OTH RCKTS TO UNDR UNIT (SUTRCT.50 [5.0] FROM N FOR MGNTIC UNITS) X F SHCS (SUPPLID IN KIT) J MOUNTING RCKTS OUTWRD R X C X J MOUNTING RCKTS INWRD X D [mm] C D 6 0 5 0 50 6.80.75.80.600.95 [.0] [7.0] [9.65] [5.] [7.5].870.75.95.60.0 [.0] [7.0] [0.0] [5.5] [8.0].95.5.5.70.70 [.0] [8.0] [.0] [8.0] [9.5].005.5.50.75.90 [5.5] [8.0] [.] [8.5] [0.0].0.55.59.8. [.0] [9.0] [.] [.] [0.5].00.55.5.885.9 [5.5] [9.0] [.5] [.5] [.0].70.9.70..5 [.0] [.5] [7.8] [8.] [.5].00.5.760.50.570 [5.0] [.0] [9.] [.0] [.5] Numbers in [ ] are in mm or for metric units [CRx5]. F 0- [M5 x.8] 0- [M5 x.8] /-0 [M6 x.0] /-0 [M6 x.0] /-0 [M6 x.0] /-0 [M6 x.0] 5/6-8 [M8 x.5] 5/6-8 [M8 x.5] DIMNSIONS G H.50.95 [5.0] [.0].50. [0.0] [8.5].75.70 [0.0] [7.].75.58 [0.0] [0.].75.87 [0.0] [7.6].75.90 [0.0] [55.7].577 [5.0] [65.5].055 [5.0] [77.6] J.90 [0.0].50 [.5].50 [.5].90 [.5].60 [6.0].670 [7.0].850 [.5].000 [5.5] K.80 [6.0].970 [50.0].50 [6.0].600 [66.0].950 [75.0].0 [8.0].90 [00.0].50 [5.0] L.80 [5.0].55 [9.0].969 [50.0].07 [5.0].6 [60.0].677 [68.0].89 [8.0].66 [9.0] M #0 [M5] #0 [M5] / [M6] / [M6] / [M6] / [M6] 5/6 [M8] 5/6 [M8] N.50 [5.0].50 [5.0].75 [0.0].75 [0.0].75 [0.0] [0.0].65 [5.0] [0.0] P.50 [8.].60 [.] [.5].890 [8.0].0 [57.0].560 [65.0].50 [80.0].660 [9.0] R.05 [.70].0 [.00].0 [.00].5 [.0].6 [.0].79 [.50].09 [5.0].50 [6.0] IMPRIL CRx 600-60- 60-60- 60-605- 606-607- KIT NO. MTRIC CRx5 608-609- 600-60- 60-60- 60-605- ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/crs -
CCSSORIS: SRIS CRS COMPCT CYLINDRS ROD Y D C HOL FOR Ø G mm PIN F THRD STUD SUPPLID UNSSMLD [mm] /6 0/5 /0 50/6.8 [.0] [.7].65 [6.0].875 [.].50 [6.5].75 [9.5] [.5].65 [6.0] C.885 [.5].065 [7.0].95 [8.0].60 [.0] DIMNSIONS D.5.9 [5.5] [5.5].55.50 [6.5] [6.5].55. [9.0] [8.0].0. 8 [.0] [.0] Numbers in [ ] are in mm or for metric units [CRx5]. F 8- [M x.7] /-8 [M6 x.0] 5/6- [M8 x.5] /8- [M0 x.5] G.96 [5.0].5 [6.0].9 [0.0].7 [.0] KIT: CRxx IMPRIL 59069-59070- 5907-5907- KIT: CRx5x MTRIC 60-605- 606-607- NOTS: ) UNIT MUST ORDRD WITH STNDRD FML THRDS ) UNLSS OTHRWIS DIMNSIOND, HOL IS CNTRD ON DSIGNTD CYLINDR CNTRLIN ) STNDRD PLTING IS RIT ZINC ROD CLVIS K (PIN LNGTH) F C D HOL FOR Ø H mm PIN (PIN SUPPLID WITH KIT) G J THRD STUD SUPPLID UNSSMLD [mm] /6 0/5 /0 50/6.8 [.0] [.7].65 [6.0].875 [.].65 [6.0] [9.0].000 [5.5].50 [.0] C.000 [5.5].55 [.0].65 [.0].85 [6.0] D.5 [5.5].55 [6.5].5 [8.0].5 [.0].9 [5.5].50 [6.5]. [8.0]. 8 [.0] Numbers in [ ] are in mm or for metric units [CRx5]. DIMNSIONS F G.6.60 [6.5] [5.5].87.78 [0.0] [9.0].5.95 [.0] [.5].60.65 [6.0] [9.5] H.96 [5.0].5 [6.0].9 [0.0].7 [.0] J 8- [M x.7] /-8 [M6 x.0] 5/6- [M8 x.5] /8- [M0 x.5] K.85 [.5].965 [.5].00 [.0].575 [0.0] KIT: CRxx IMPRIL 5907-5907- 59075-59076- KIT: CRx5x MTRIC 608-609- 600-60- NOTS: ) UNIT MUST ORDRD WITH STNDRD FML THRDS ) UNLSS OTHRWIS DIMNSIOND, HOL IS CNTRD ON DSIGNTD CYLINDR CNTRLIN ) STNDRD PLTING IS RIT ZINC (PIN & CLVIS) - (800) 6-85 www.phdinc.com/crs ll dimensions are reference only unless specifically toleranced. CT-0
CCSSORIS: SRIS CRS COMPCT CYLINDRS ROD FULCRUM PIN KIT Replacement for Rod Clevis pin or for use with PHD Rod ye. Pin is rite Zinc plated. Retaining rings supplied. [mm] /6 0/5 /0 50/6.665 [7.0].785 [0.0].05 [6.5].95 [.0] DIMNSIONS ØC.85.96 [.5] [5.0].965.5 [.5] [6.0].00.9 [.0] [0.0].575.7 [0.0] [.0] ØD.5 [.0].56 [.0].7 [7.0].5 [9.0] KIT: CRxx, CRx5x IMPRIL/MTRIC Numbers in [ ] are in mm or for metric units [CRx5]. 606-607- 608-609- Ø D Ø C CYLINDR FULCRUM PIN KIT Replacement for base pivot pin or for use with PHD Cylinder Pivot. Pin is rite Zinc plated. Retaining rings supplied. [mm] /6 0/5 /0 50/6.0 [8.5].550 [9.5].0 [.5].690 [.0] DIMNSIONS ØC.00.96 [.0] [5.0].70.5 [.0] [6.0].90.9 [8.0] [0.0].970.7 [50.0] [.0] ØD.5 [.0].56 [.0].7 [7.0].5 [9.0] KIT: CRxx, CRx5x IMPRIL/MTRIC 600- Numbers in [ ] are in mm or for metric units [CRx5]. 60-60- 60- Ø D Ø C ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/crs -5
PPLICTIONS: SRIS CRS COMPCT CYLINDRS ST PRCTICS FOR MXIMUM CYLINDR LIF Shown below are the best ways to apply PHD Series CRS Cylinders. The key to proper application and long cylinder life is using the cylinder to provide power and motion while externally stopping any attached loads. PPLICTION # - TTCHD LOD Loads connected to the cylinder rod must always be stopped externally. Strokes, rod lengths, and attached loads should be designed so that the piston never impacts the head or cap. For vertical applications only. XTNSION RTRCTION PISTON DOS NOT IMPCT TH HD OR CP LOD IS XTRNLLY STOPPD PRIOR TO PISTON IMPCTING NDS OF CYLINDR TTCHD LOD TTCHD LOD PPLICTION # - UNTTCHD LOD Shock pads are recommended in applications where the cylinder is operated with an unattached load and the piston is impacting the head and/or the cap. The use of these optional built-in shock pads will ensure maximum cylinder life and reduce end-ofstroke noise. XTNSION SHOCK PDS RTRCTION UNTTCHD LOD UNTTCHD LOD -6 (800) 6-85 www.phdinc.com/crs CT-0
COMPCT CYLINDRS SRIS CTS INDX: Ordering Data Page - enefits & Construction Page - Compact size and guide shafts are ideal for non-rotating applications where length is critical. Dimensions Pages - and -5 ngineering Data Pages -6 to -8 Options Pages -9 and -0 ccessories Pages - and - Compact Cylinder pplications Page - and - CT-0 (800) 6-85 www.phdinc.com/cts -
ORDRING DT: SRIS CTS COMPCT GUID ROD CYLINDRS TO ORDR SPCIFY: Product, Series, Type, Design No., Mounting Style, ore Size, Stroke, and Options. PRODUCT C - Cylinder TYP S - Single Rod, Double cting (Standard) D - Double Rod, Double cting Double rod units include tool plate on one end only. MOUNTING STYL ll units have thru holes U - Universal (Standard) Thread and C'bore Places, ach nd J - Foot Mounting Foot Inward, each end K - Foot Mounting Foot Outward, each end IMPRIL STROK (CTx) STNDRD STROK LNGTHS /8" = Minimum stroke in /8" increments mm 6 0 5 0 50 6 MXIMUM STROK (in) -/ -/ -/8 -/8-5/8-7/8 -/ 6 MTRIC STROK (CTx5) STNDRD STROK LNGTHS 5 mm = Minimum stroke in 5 mm increments mm 6 0 5 0 50 6 MXIMUM STROK [mm] 60 70 85 85 90 95 95 50 C T S U x / - M- T - SRIS Compact Guide Rod DSIGN NO. - Imperial 5 - Metric NOTS: ) Option -V may reduce cylinder lifespan due to fluoro-elastomer seal material. ) Option -Z may reduce cylinder lifespan due to stainless steel rod in place of chrome-plated stressproof. ccessories- see page -.! mm 6 0 5 0 50 6 SIZ R in mm.7.6.79.98.6.57.97.8 0 90 80 56 96 7 in.75..87.76.7.98.0.8 Options may affect unit length. See unit dimension and options pages for adders. I M F K_ V W WR WR Z OPTIONS - Shock Pads in both directions (Option does not add any extra length) - Magnetic piston for use with PHD Magnetoresistive Switches - Magnetic piston for use with PHD Miniature Reed Switches - xtended length wrench flats - xtra Tool Plate xtension in /8" [5 mm] increments up to " [5 mm] maximum Length code example: K = /8", K = /8", or K5 = 5 mm, K5 = 5 mm, etc. - Fluoro-lastomer seals. See Note. - lank Tool Plate (shipped with tool plate unassembled) - Rectangular tool plate (-6 mm units only) - lank rectangular tool plate (-6 mm units only)(shipped with tool plate unassembled) - Corrosion-resistant, stainless steel rod and guideshafts, electroless nickel plated retaining rings, fasteners, and rackets (with J & K mounting) See Note. - (800) 6-85 www.phdinc.com/cts CT-0
COMPCT GUID ROD CYLINDRS: SRIS CTS NFITS The compact size of the Series CTS Compact Guide Rod Cylinder makes it ideal for non-rotating cylinder applications where unit length is critical. The CTS also performs as a light duty slide where precise location is not required and side loading is limited. Compact Guide Rod Cylinders prevent rotation of tooling connected to cylinder. Standard tool plate allows easy mounting of PHD Series 90 & 9 Grippers. Optional blank tool plate is available for customers to add their own mounting pattern. Diagonal tool plate allows front mounting of the cylinder while still permitting full tool plate retraction. Thru and threaded holes for easy cylinder mounting. Flange brackets and optional accessories provide additional mounting flexibility. Field repairable for extended life. Nitrile piston and rod seals for long life and low maintenance. Optional fluorocarbon seals for fluid compatibility. Consult PHD for high temperature use. Optional shock pads extend cylinder life and minimize piston noise in applications where the piston contacts the head and/or cap. The shock pad design adds no additional length to the cylinder. Switches may be mounted on three sides of the cylinder for maximum flexibility (two sides for and 6 mm sizes) and provide a signal on extension and retraction with strokes as short as /8 inch [5 mm]. CONSTRUCTION Hard chrome-plated steel piston rod provides maximum wear resistance for long life. Hardcoated bore for extended cylinder life. Long life Nitrile piston and rod seals for low maintenance. ronze rod bushings are standard on mm through 0 mm, hardcoated aluminum rod bushings on 50 mm and 6 mm. 5 nodized aluminum tool plate for low weight and oxidation resistance. 6 Hard chrome-plated steel guideshafts provide wear resistance for long life. 7 Oil-impregnated bronze bushings provide lubrication over the life of the unit. 5 6 7 CT-0 (800) 6-85 www.phdinc.com/cts -
DIMNSIONS: SRIS CTS COMPCT GUID ROD CYLINDRS - 6 mm H X Ø GUID ROD x T WRNCH FLT x.5 [.0] LONG X (R) X DRILL & C FOR S SHCS R THRD (X THIS ND OPPOSIT SID) F X SWITCH MOUNTING SLOT G C X D S TOOL PLT DIMNSIONS PG -5 FOR MOUNTING PTTRN DIMNSIONS Ø U ROD V WRNCH FLT x.5 [.0] LONG X D.57 [.0]* K L J + STROK *NOT: S J & K MOUNTING DIMNSIONS FOR STNDRD XTNSION WITH THOS OPTIONS M X N PORT P Z THRD DOUL ROD ONLY.57 [.0] + STROK DOUL ROD ONLY 0-6 mm F W S TOOL PLT DIMNSIONS PG -5 FOR MOUNTING PTTRN DIMNSIONS X SWITCH MTG SLOT X Ø GUID ROD x T WRNCH FLT x.5 [.0] LONG L M X (R) X N PORT F X Y Ø U ROD V WRNCH FLT x.5 [.0] LONG P Z THRD DOUL ROD ONLY X DRILL & C FOR S SHCS R THRD (X FOR THIS ND OPPOSIT SID) / C C.57 [.0]* K J + STROK *NOT: S J & K MOUNTING DIMNSIONS FOR STNDRD XTNSION WITH THOS OPTIONS.57 [.0] + STROK DOUL ROD ONLY [mm] 6 0 5 0 50 6.876 [.5].000 [5.50].75 [5.00] [8.00] [.50].000 [5.00] [6.50].97 [75.50].00 [0.50].50 [.75] C.59 [5].70 [8].906 [].0 [6].78 [5].650 [].086 [5].560 [65] Numbers in [ ] are in mm or for metric units [CTx5]. DIMNSIONS D D F G H J K L M.8.00.9.550.866.60.80.95.5.5 [.6] [0.5] [.0] [.0] [.0] [.0] [5.0] [7.5] [0.5] [0.5].05.075.0.70.96.0.80.95.5.5 [0.6] [.9] [8.0] [8.0] [.0] [.0] [5.0] [7.5] [0.5] [0.5].76.000.65.9.670.5 [7.5] [5.] [.0] [0.0] [7.0] [0.5].576.00.65.9.670.5 [0.0] [8.0] [.0] [0.0] [7.0] [0.5].870.9.790.9.70.50 [7.5] [.0] [5.5] [0.0] [8.0] [.5].05.575.790.9.70.50 [56.0] [0.0] [5.5] [0.0] [8.0] [.5].598.969.970.55.790.55 [66.0] [50.0] [50.0] [.0] [0.0] [.5].070.60.090.55.865.570 [78.0] [60.0] [5.0] [.0] [.0] [.5] N 0- x.5 [M5 x.8 x ] 0- x.5 [M5 x.8 x ] 0- x.5 [M5 x.8 x ] 0- x.5 [M5 x.8 x ] /8 NPT [/8 SP] /8 NPT [/8 SP] /8 NPT [/8 SP] / NPT [/ SP] P.0 [.0].5 [.5].5 [.5].55 [.0].60 [5.5].78 [8.75].8 [.0].865 [.0] R THRD 0- x.550 [M5 x.8 x.5] 0- x.550 [M5 x.8 x.5] /-0 x.875 [M6 x.0 x.5] /-0 x.875 [M6 x.0 x.5] /-0 x.875 [M6 x.0 x.5] /-0 x.875 [M6 x.0 x.5] 5/6-8 x.900 [M8 x.5 x.5] 5/6-8 x.900 [M8 x.5 x.5] S #6 [M] #6 [M] #0 [M5] #0 [M5] #0 [M5] #0 [M5] / NOTS: ) DSIGNTD CNTRLIN IS CNTRLIN OF CYLINDR ) UNLSS OTHRWIS DIMNSIOND, MOUNTING HOL PTTRNS R CNTRD ON DSIGNTD CYLINDR CNTRLIN ) TOLRNC ON STROK IS ±.0" [±.8 mm] ) /8" [5 mm] MINIMUM STROK RQUIRD 5) DIMNSIONS SHOWN IN [ ] R IN mm OR FOR MTRIC UNITS [CTx5] [M6] / [M6] T.9 [5.5].9 [5.5].50 [7.0].50 [7.0].50 [7.0].50 [7.0]. [8.0]. [8.0] U.50 [6.5].50 [6.5].75 [9.5].75 [9.5].65 [5.9].65 [5.9] [9.0] [9.0] V.9 [5.5].9 [5.5]. W.576 X. Y.788 [8.0] [0.0] [8.75] [0.0]..76.88.000 [8.0] [.5] [7.0] [5.].07.66.0 [.0] [5.0] [6.75] [.0].6.9.0 [.0] [60.0] [0.0] [.0].65.795.97.0 [6.0] [7.0] [.6] [.0].65.66.88.0 [6.0] [8.0] [.] [6.] [mm] -6 0-0 50-6 Z THRD 6- x.0 [M x.5 x 5] 6- x.0 [M x.5 x 5] 0- x.85 [M5 x.8 x 7] 0- x.85 [M5 x.8 x 7] /-8 x.75 [M6 x.0 x 9] /-8 x.75 [M6 x.0 x 9] 5/6- x. [M8 x.5 x 8] 5/6- x. [M8 x.5 x 8] DIMNSIONS [6.0] [8.0] [0.0] - (800) 6-85 www.phdinc.com/cts ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS CTS COMPCT GUID ROD CYLINDRS TOOL PLT X D X G THDS THRU PTTRN FOR H GRIPPR (J SHCS RQUIRD FOR MTG H GRIPPR R NOT SUPPLID) X THRU HOLS FOR M SHCS C' ON OPPOSIT SID PTTRN FOR N GRIPPR (P SHCS RQUIRD FOR MTG N GRIPPR R NOT SUPPLID) X D X F X K SQ X L X F X X G THRDS THRU PTTRN FOR H GRIPPR (J SHCS RQUIRD FOR MTG H GRIPPR R NOT SUPPLID) C R HX C / C R HX X S HX X S HX - 6 mm 0-6 mm [mm] 6 0 5 0 50 6.876 [.5].000 [5.5].75 [5.0] [8.0] [.5].000 [5.0] [6.5].97 [75.5].00 [0.5].50 [.75] C.59 [5.0].70 [8.0].906 [.0].0 [6.0].78 [5.0].650 [.0].086 [5.0].560 [65.0] D.8 [.60].05 [0.6] D.00 [0.50].075 [.90].550 [.0].550 [.0].70 [8.0] 0.70 [8.0].00 [8.0].00 [8.0].55 [9.0].55 [9.0] F.75 [7.0].75 [7.0].55 [9.0].55 [9.0].55 [.0].55 [.0].768 [9.5].768 [9.5] G -0 [M x.5] -0 [M x.5] 6- [M x.5] 6- [M x.5] 8- [M x.7] 8- [M x.7] 0- [M5 x.8] 0- [M5 x.8] DIMNSIONS H (SRIS 90)* NGULR PRLLL 906x [900] [906x] 906x [900] [906x] 907x [90] [907x] 907x [90] [907x] 908x [90] [908x] 908x [90] [908x] 909x [90] [909x] 909x [90] [909x] J -0 x [M x.5 x 0] -0 x [M x.5 x 0] 6- x -/ [M x.5 x 0] 6- x -/ [M x.5 x 0] 8- x -5/8 [M x.7 x 0] 8- x -5/8 [M x.7 x 0] 0- x -/ [M5 x.8 x 55] 0- x -/ [M5 x.8 x 55] K 0.550 [.0] 0.550 [.0] 0.70 [8.0] 0.70 [8.0].00 [8.0].55 [9.0] L.75 [7.0].75 [7.0].55 [9.0].55 [9.0].550 [.0].768 [9.5] M # [M] # [M] #6 [M] #6 [M] #8 [M] #0 [M5] N (SRIS 9x)* NGULR PRLLL [9x0] [9x0] [9x] [9x] [9x] [9x] 9x6x [9x6x] 9x6x [9x6x] 9x7x [9x7x] 9x7x [9x7x] 9x8x [9x8x] 9x9x [9x9x] P -0 x /8 [M x.5 x 0] -0 x /8 [M x.5 x 0] 6- x /8 [M x.5 x 8] 6- x /8 [M x.5 x 8] 8- x 5/8 [M x.7 x ] 0- x / [M5 x.8 x ] R [.0] [.0] [5.0] [5.0] [6.0] [6.0] [8.0] [8.0] S [.0] [.0] [.0] [.0] [.0] [.0] [5.0] [5.0] NOTS: ) Numbers in [ ] are in mm or for metric units [CTx5]. ) *Imperial grippers mount to CTx only. Metric grippers mount to CTx5 only. OPTIONL RCTNGULR TOOL PLT (-6 mm ONLY) -WR and -WR options (lank without mounting holes) K SQ X L CL X F X X THRU HOLS FOR M SHCS C' ON OPPOSIT SID. PTTRN FOR N GRIPPR (P SHCS RQUIRD FOR MTG N GRIPPRS R NOT SUPPLID) X G THDS THRU PTTRN FOR H GRIPPR (J SHCS RQUIRD FOR MTG H GRIPPR R NOT SUPPLID) R HX X S HX [mm] 6.876 [.5].000 [5.5].00 [0.5].50 [.75].550 [.0].550 [.0] F.75 [7.0].75 [7.0] G -0 [M x.5] -0 [M x.5] H (SRIS 90*) NGULR PRLLL 906x [900] [906x] 906x [900] [906x] NOTS: ) Numbers in [ ] are in mm or for metric units [CTx5]. ) *Imperial grippers mount to CTx only. Metric grippers mount to CTx5 only. DIMNSIONS J -0 x [M x.5 x 0] -0 x [M x.5 x 0] K.550 [.0].550 [.0] L.75 [7.0].75 [7.0] M # [M] # [M] N (SRIS 9x)* NGULR PRLLL 9x6x [9x0] [9x6x] 9x6x [9x0] [9x6x] P -0 x /8 [M5 x.5 x 8] -0 x /8 [M x.5 x 8] R [.0] [.0] S [.0] [.0] ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cts -5
NGINRING DT: SRIS CTS COMPCT GUID ROD CYLINDRS PRFORMNC DT: HORIZONTL PPLICTIONS Proper application of CTS Cylinders in horizontal applications is dependent upon travel and attached load. In addition, where there is end-of-stroke impact with an attached load, cylinder speed must be considered. [5] TTCHD LOD WITHOUT ND OF STROK IMPCT Use the charts below to determine the Maximum Rolling Side Load for a given bore size and travel. Optimum performance will be achieved with positive external stops aligned with the cylinder centerline. TTCHD LOD WITH ND OF STROK IMPCT Use the charts below to determine the Maximum Rolling Side Load and speed for a given bore size and travel. Optional shock pads are required for end-of-stroke impact with attached load. C.G. OF TTCHD LOD LIGND WITH CYLINDR CL TOOL PLT XTNSION TRVL STROK NOTS: ) HORIZONTL SID LOD PRFORMNC DT IS SD UPON ) TH CNTR OF GRVITY (C.G.) OF TH TTCHD LOD LOCTD S SHOWN OV. LOCTING TH C.G. YOND TH STTD DISTNC MY DCRS TH LIF OF TH UNIT. ) STNDRD UNIT. US OF FLUORO-LSTOMR SLS OR TH -Z OPTION MY DCRS TH SID LODING CPILITY OF TH UNIT. ) SPDS R SD ON ND-OF-STROK IMPCT CPILITY OF UNITS WITH OPTIONL SHOCK PDS. LOD lb [N] 0.70 [.] 0.60 [.67] 0.50 [.] 0.0 [.78] 0.0 [.] 0.0 [0.89] 0.0 [0.] 5 in/sec [.8 m/sec] CTx 0 in/sec [.5 m/sec] MXIMUM HORIZONTL LOD CPCITY & SPD 5 in/sec [.6 m/sec] Maximum rolling side load LOD lb [N].0 [6.].0 [5.].00 [.5] 0.80 [.56] 0.60 [.67] 0.0 [.78] 0.0 [0.90] in/sec [.6 m/sec] CTx6 5 in/sec [.8 m/sec] 0 in/sec [.5 m/sec] Maximum rolling side load 5 in/sec [.6 m/sec] 0 0 0.5 [6.] 0.50 [.7] 0.75 [9.].00.5.50.75 [5.] [.8] [8.] [.5] TRVL inch [mm].00 [50.8].5 [57.].50 [6.5].75 [69.9] 0 0 0.5 [6.] 0.50 [.7] 0.75 [9.].00 [5.].5 [.8].50 [8.].75 [.5].00 [50.8] TRVL inch [mm].5 [57.].50.75 [6.5] [69.9].00.5 [76.] [8.6] CTx0 CTx5 LOD lb [N] 6.00 [6.7] 5.00 [.].00 [7.8].00 [.].00 [8.9].00 [.] in/sec [.8 m/sec] 5 in/sec [.8 m/sec] 0 in/sec [.5 m/sec] 5 in/sec [.6 m/sec] Maximum rolling side load LOD lb [N] 7.00 [.] 6.00 [6.7] 5.00 [.].00 [7.8].00 [.].00 [8.9].00 [.] in/sec [.6 m/sec] 5 in/sec [.8 m/sec] 0 in/sec [.5 m/sec] 5 in/sec [.6 m/sec] Maximum rolling side load 0 0 0.50 [.7].00 [5.].50 [8.].00 [50.8].50 [6.5] TRVL inch [mm].00 [76.].50 [88.9].00 [0.6].50 [.] 0 0 0.50 [.7].00 [5.].50 [8.].00 [50.8].50 [6.5] TRVL inch [mm].00 [76.].50 [88.9].00 [0.6].50 [.] LOD lb [N] 7.00 [.] 6.00 [6.7] 5.00 [.].00 [7.8].00 [.].00 [8.9].00 [.] 5 in/sec [.8 m/sec] CTx 0 in/sec [.5 m/sec] 5 in/sec [.6 m/sec] Maximum rolling side load LOD lb [N] 9.00 [0.0] 8.00 [5.6] 7.00 [.] 6.00 [6.7] 5.00 [.].00 [7.8].00 [.].00 [8.9].00 [.] 5 in/sec [.8 m/sec] CTx0 0 in/sec [.5 m/sec] 5 in/sec [.6 m/sec] Maximum rolling side load 0 0 0.50 [.7].00 [5.].50 [8.].00 [50.8].50 [6.5] TRVL inch [mm].00 [76.].50 [88.9].00 [0.6].50 [.] 0 0 0.50 [.7].00 [5.].50 [8.].00 [50.8].50 [6.5].00 [76.] TRVL inch [mm].50 [88.9].00 [0.6].50 [.] 5.00 [7.0] -6 (800) 6-85 www.phdinc.com/cts CT-0
NGINRING DT: SRIS CTS COMPCT GUID ROD CYLINDRS PRFORMNC DT: HORIZONTL PPLICTIONS LOD lb [N].00 [6.].00 [5.] 0.00 [.5] 8.00 [5.6] 6.00 [6.7].00 [7.8].00 [8.9] in/sec [.6 m/sec] 5 in/sec [.8 m/sec] CTx50 0 0 0.50.00.50.00.50.00 [.7] [5.] [8.] [50.8] [6.5] [76.] TRVL inch [mm] MXIMUM HORIZONTL LOD CPCITY & SPD 0 in/sec [.5 m/sec] 5 in/sec [.6 m/sec] Maximum rolling side load.50 [88.9].00 [0.6].50 [.] 5.00 [7.0] LOD lb [N] 5.00 [66.7].00 [57.8].00 [8.9] 9.00 [0.0] 7.00 [.] 5.00 [.].00 [.] in/sec [.6 m/sec] 5 in/sec [.8 m/sec] CTx6 0 in/sec [.5 m/sec] 5 in/sec [.6 m/sec].00 [.] 0 0 0.50.00.50.00.50.00.50 [.7] [5.] [8.] [50.8] [6.5] [76.] [88.9] TRVL inch [mm].00 [0.6].50 [.] Maximum rolling side load 5.00 [7.0] 5.50 [9.7] 6.00 [5.] PRFORMNC DT: VRTICL PPLICTIONS Proper application of CTS Cylinders in vertical applications is dependent upon both attached load and cylinder speed. TTCHD LOD WITHOUT ND OF STROK IMPCT See cylinder force table on page -8. Optimum performance will be achieved with positive external stops aligned with the cylinder centerline. TTCHD LOD WITH ND OF STROK IMPCT Use the charts below to determine the maximum speed for a given load. Optional shock pads are required for end-of-stroke impact with attached load. NOTS: ) VRTICL PRFORMNC DT IS SD UPON: ) TH CNTR OF GRVITY (C.G.) OF TH TTCHD LOD IN LIN WITH TH CYLINDR CNTRLIN. LOCTING TH C.G. OFF OF TH CYLINDR CNTRLIN MY RSULT IN DCRSD CYLINDR LIF. ) STNDRD UNIT. US OF FLUORO-LSTOMR SLS OR TH -Z OPTION MY DCRS TH LIF OF TH UNIT. ) SPDS R SD ON ND OF STROK IMPCT CPILITY OF UNITS WITH OPTIONL SHOCK PDS VRTICL PPLICTION WITH ND OF STROK IMPCT MXIMUM SPD & LOD 0.0 [0.76] CTx, CTx6, CTx0, CTx5 0.0 [0.76] CTx, CTx0, CTx50, CTx6 MXIMUM SPD in/sec [m/sec] 5.0 [0.6] 0.0 [0.5] 5.0 [0.8] 0.0 [0.5] 5.0 [0.] CTx CTx6 CTx0 0 0.0.0 6.0 8.0 0.0.0 [8.9] [7.8] [6.7] [5.6] [.5] [5.] LOD lb [N].0 [6.] 6.0 [7.] CTx5 8.0 0.0 [80.] [89.0] MXIMUM SPD in/sec [m/sec] 5.0 [0.6] 0.0 [0.5] 5.0 [0.8] 0.0 [0.5] 5.0 [0.] CTx CTx0 CTx50 0 0 0.0 0.0 60.0 80.0 [89] [78] [67] [56] LOD lb [N] 00.0 [5] CTx6 0.0 [5] 0.0 [6] CT-0 (800) 6-85 www.phdinc.com/cts -7
NGINRING DT: SRIS CTS COMPCT GUID ROD CYLINDRS mm in ROD DI. ROD FFCTIV R in mm DIRCTION in mm lb N 6 0 5.7.60.787.98.50.50.75.75 6.5 6.5 9.5 9.5 PUSH PUSH PUSH PUSH.75..87.76 0 90.5 6 9.5 5 6 8 68 PULL PULL PULL PULL.6.6.76.650 8 69 9.5 5.5 7.5 58 0 50 6.60.575.969.80.65 5.88.65 5.88 9.05 9.05 PUSH PUSH PUSH PUSH.7.98.0.8 80 56 96 7 5 9 6 97 7 7 0 PULL PULL PULL PULL.90.6.60.90 606 058 678 8 9 5 88 8 6 9 Note: Use pull forces for calculating double rod end performance. CYLINDR FORC TL CYLINDR FORC IN POUNDS FOR psi ND IN NWTONS FOR bar 0 /.8 0 /.76 60 /. 80 / 5.5 00 / 6.90 0 / 8.8 50 / 0.5 lb N lb N lb N lb N lb N lb N 7 0.5 7 6 7.5 78 9 6 7 5 7.5 0 5.5 56 5 67 9 8.5 55 8.5 8 5 9 7 66 7 08 0.5 7 6 70 9 6 7 0 9 75 9.5 87 9 0 9 7 9 7 58 60 7 5 5 67 0 0 8 68 5 0 57 5 0 5 6 0 6 7 76 8 9 06 508 6 6 9 7 5 65 89 78 7 98 50 75 00 5 555 50 665 87 8 8 67 56 5 75 9 8 50 67 78 7 7 50 56 69 95 866 00 9 00 66 9 99 8 58 6 70 97 876 6 095 5 8 8 08 0 5 65 65 57 0 0 6 56 69 08 96 60 57 89 90 76 9 860 90 90 87 79 8 9 580 579 75 76 78 6 7 5 56 9 95 57 659 99 SIZ mm 6 mm 0 mm 5 mm mm 0 mm 50 mm 6 mm CYLINDR WIGHT TL S WIGHT lb kg.9.09..0.9.8.5..80.6.7.5.5.66.0.9 DDR PR " [5 mm] OF STROK lb kg..05..05.6.07..09....6.5.0.55.5 PRSSUR RTINGS ll Series CTS Compact Guide Rod Cylinders have a maximum pressure rating of 50 psi [0 bar] air and are for pneumatic use only. RKWY The breakaway pressure is 0 psi [.5 bar] at zero load. TMPRTUR LIMITS - SLS Series CTS Compact Guide Rod Cylinders are equipped with long life Nitrile seals suitable for use in temperatures ranging from -0 to +80 F [-8 to +8 C]. STROK TOLRNC Tolerance on the nominal stroke length is ± / inch [±.8 mm]. VLOCITY verage minimum velocity of unit is designed to be 0 in/sec [.5 m/sec] with zero load at 00 psi [7 bar]. LURICTION ll units are permanently lubricated at the factory and can be used with non-lubricated air. Seals are compatible with standard petroleum-based oil used for lubrication of air cylinders. LIF XPCTNCY Series CTS Cylinders have been tested to 5 million trouble-free cycles under normal conditions (see pages -6 and -7 for Performance Data). Non-lubricated air, option -V and option -Z may reduce life expectancy. MINTNNC s with most PHD products, these cylinders are field repairable. Rebuild kits, piston and rod assemblies, and main structural components are available as needed for extended service. PPLICTION The PHD Series CTS Compact Guide Rod Cylinders are designed for use as compact non-rotating cylinders and as light duty slides where precise location is not required and side loading is minimal. On double rod units, rear rod increases stability of the tool plate. Rear rod thread not intended as a load attach point. Shock pads are intended for use where there is end-of-stroke impact with an attached load. For maximum cylinder life with attached load, PHD recommends the use of external stops or shock absorbers. For maximum load and kinetic energy performance data, see pages -6 and -7. See best application practices on pages - and -. SHOCK PD USG Optional shock pads are recommended for applications where the piston contacts the head and/or cap with an attached load. The use of shock pads reduces noise and provides maximum cylinder life in these applications. Shock pads are not required for applications where external stops prevent end-of-stroke impact or where end impact occurs without an attached load. See best application practices on pages - and -. -8 (800) 6-85 www.phdinc.com/cts CT-0
OPTIONS: SRIS CTS COMPCT GUID ROD CYLINDRS SHOCK PDS ON XTNSION ND RTRCTION Shock pads eliminate metal-to-metal contact and minimize piston impact. Shock pads are recommended for applications where the piston contacts the head and/or cap (with attached loads). The use of shock pads reduces noise and provides maximum cylinder life in these applications. SHOCK PDS F XTNDD LNGTH WRNCH FLTS The design of a compact guide rod cylinder requires the length to be as short as possible. The standard wrench flat length is.5" [ mm]. The option -F provides wrench flats which allow standard wrench access. On double rod units, rear rod also receives extended flats with option -F. DOUL ROD UNITS ONLY [mm] /6 0/5 /0 50/6 XTNDD ROD & GUID SHFT WRNCH FLTS.00.00.90.90 [5.5] [5.5] [8.00] [8.00] ROD XTNSION.50 [6.5].50 [6.5]. [9.0]. [9.0] Numbers in [ ] are in mm or for metric units [CTx5]. STROK K_ XTR TOOL PLT XTNSION xtra tool plate extension can be specified by calling out the -K option followed by the length code. Length code example (for imperial CTx units) K = /8" of extra tool plate extension K = /8", etc..57 [.0] STD XTNSION K_ XTR TOOL PLT XTNSION DOUL ROD UNITS ONLY Length code example (for metric CTx5 units) K5 = 5 mm of extra tool plate extension K5 = 5 mm, etc..57" [ mm] of tool plate extension is standard. vailable in /8" [5 mm] increments only. Maximum extension is " [5 mm]. NOT: On double rod units, rear rod receives same extension as tool plate (tool plate on front end only). STROK K_ XTR TOOL PLT XTNSION.57 [.0] STD XT ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cts -9
OPTIONS: SRIS CTS COMPCT GUID ROD CYLINDRS I MGNT FOR PHD MGNTORSISTIV SWITCHS TYP This option equips the cylinder with a magnetic band on the piston for use with PHD Magnetoresistive Switches. These switches mount easily to the cylinder using T slots in the body. M MGNT FOR PHD MINITUR RD SWITCHS This option equips the cylinder with a magnetic band on the piston for use with PHD Series 560 Miniature Reed Switches. These switches mount easily to the cylinder using T slots in the body. SWITCH MOUNTING TL MINIMUM STROK FOR TWO SWITCHS ON ON SID [mm] 6 0 5 0 50 6.00 [8.0].00 [8.0].00 [5.5].50 [6.5].50 [6.5].50 [6.5].00 [8.0].00 [8.0] Numbers in [ ] are in mm or for metric units [CTx5]. TYP [mm] C RD 5609--0 569- DC RD 560--0 56- MGNTO- RSISTIV 5605--0 5606--0 565-566-, 6, 0 [5].65 [0].5 [0] 5,, 0 [0] [0].5 [0] 50, 6.75 [5].75 [5].000 [5] WR RCTNGULR TOOL PLT With this option, available only on the -6 mm cylinders, the unit is assembled with a rectangular tool plate. This provides an additional mounting orientation for Series 90 and 9 Grippers. W WR LNK TOOL PLT LNK RCTNGULR TOOL PLT With this option, PHD provides a tool plate without mounting threads and counterbores. The tool plate is supplied unassembled for easy modification by the customer. ssembly and torque specifications are furnished with each unit. When assembling the unit, a threadlocking adhesive is required. NOT: lank tool plate is shipped unassembled. V FLUORO-LSTOMR SLS Z CORROSION RSISTNT Fluoro-lastomer seals are compatible with certain fluids which degrade standard Nitrile seals. Seal compatibility should be checked with the fluid manufacturer for correct application. Consult PHD for high temperature use. lectroless nickel plating is provided on the retaining rings, tool plate mounting screws, J and K brackets, and bracket mounting screws. Stainless steel rod and guideshafts are also supplied. This option may reduce unit life. -0 (800) 6-85 www.phdinc.com/cts ll dimensions are reference only unless specifically toleranced. CT-0
CCSSORIS: SRIS CTS COMPCT GUID ROD CYLINDRS CYLINDR PIVOT X H SHCS (SUPPLID IN KIT) F RD G HOL FOR Ø J mm PIN C X H SHCS (SUPPLID IN KIT) G HOL FOR Ø J mm PIN [mm] 6 0 5 0 50 6 C D.650 [6.5].650 [6.5].790 [0.0].790 [0.0].065 [7.0].065 [7.0].60 [7.0].60 [7.0].68 [6.5].678 [7.5] [9.0].800 [0.5].95 [.0].05 [8.0].00 [.0] [8.0] / D C RONZ L USHING - 5 mm D -6 mm DIMNSIONS KIT NO. KIT NO. D F G H J IMPRIL CTx MTRIC CTx5.06.76.8.9 0-.97 [7.0] [.0] [7.5] [.0] [M5 x.8] [5.0] 6078-6086-.06.56.8.9 0-.97 [7.0] [5.0] [7.5] [.0] [M5 x.8] [5.0] 6079-6087-.55.5 /-0.7 [8.0] [8.0] [9.0] [9.0] [M6 x.0] [6.0] 6080-6088-.600.55.5 /-0.7 [8.0] [.0] [9.0] [9.0] [M6 x.0] [6.0] 608-6089-.870.870.80.75 /-0.9 [8.0] [8.0] [.0] [7.5] [M6 x.0] [0.0] 608-6090-.0.0.80.75 /-0.9 [56.0] [56.0] [.0] [7.5] [M6 x.0] [0.0] 608-609-.600.600.000.970 5/6-8.7 [66.0] [66.0] [5.5] [50.0] [M8 x.5] [.0] 608-609-.000.000.000.970 5/6-8.7 [76.0] [76.0] [5.5] [50.0] [M8 x.5] [.0] 6085-609- C.905 [.0].905 [.0].50 [.75].50 [.75].56 [.5].56 [.5].66 [6.5].66 [6.5] Numbers in [ ] are in mm or for metric units [CTx5]. F NOTS: ) -5 mm IS RIT ZINC PLTD STL ) -6 mm IS NODIZD LUMINUM WITH LURICTD RONZ USHINGS ) FULCRUM PIN NOT INCLUDD (S FULCRUM PIN KITS TO PURCHS) S PIVOT X THRU HOL FOR J SHCS X RONZ USHING X THRU HOL FOR J SHCS X RONZ USHING M L N K M L HOL FOR Ø F mm PIN (PIN SUPPLID WITH KIT) H HOL FOR Ø F mm PIN (PIN SUPPLID WITH KIT) H [mm] /6 0/5 /0 50/6.865 [.0].000 [5.5].75 [5.0].890 [8.0].5 [9.0].55 [.5].800 [6.0].65 [60.0] C.650 [6.5].790 [0.0].065 [7.0].60 [7.0] D.90 [.5].60 [6.0].600 [5.].755 [9.].0 [5.6].60 [6.5].00 [0.].505 [.0] F.97 [5.0].7 [6.0].9 [0.0].7 [.0] Numbers in [ ] are in mm or for metric units [CTx5]. * PHD CYLINDR PIVOT * **G NOT INCLUDD **G D C D C - 5 mm -6 mm DIMNSIONS G H.060.75 [.5] [9.5].00.5 [.0] [.0].56.50 [.0] [.0].6.709 [6.0] [8.0] J #0 [M5] / [M6] / [M6] 5/6 [M8] K N/ N/.695 [.0].65 [57.5] L.905 [.0].50 [.75].50 [.5].650 [6.5] M.00 [.0].70 [.0].90 [8.0].970 [50.0] N N/ N/.65 [55.0].85 [7.0] KIT: CTxx, CTx5x IMPRIL/MTRIC 609-6095- 6096-6097- PHD CYLINDR PIVOT NOT INCLUDD NOTS: ) -5 mm IS RIT ZINC PLTD STL WITH LURICTD RONZ USHINGS ) -6 mm IS NODIZD LUMINUM WITH LURICTD RONZ USHINGS ) FULCRUM PIN INCLUDD. DOS NOT INCLUD CYLINDR PIVOT ) * IS TO CNTR OF PIVOT PIN 5) **G IS FROM CNTR OF PIVOT PIN TO CNTR OF FIRST MOUNTING HOL ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cts -
MOUNTING OPTIONS: SRIS CTS CYLINDRS J J MOUNTS K K MOUNTS J mounting provides foot brackets (with mounting feet under the cylinder) with minimal distance between the cylinder and mounting surface. This mounting comes preassembled by PHD with proper tool plate extension where required. NOT: Double rods will also receive H standard extension. K mounting provides foot brackets (with mounting feet extended outward from the cylinder.) Mounting is simplified with mounting holes away from the body. This mounting comes preassembled by PHD with proper tool plate extension where required. NOT: Double rods will also receive H standard extension. + STROK D + STROK THRU HOL FOR P SHCS C F + STROK G + STROK J K H STNDRD XTNSION WITH J OR K MOUNTING (TOOL PLT XTNSION OR XTNDD WRNCH FLTS WILL DD TO THIS DIMNSION) L X N K MOUNTING RCKTS OUTWRD [mm] 6 0 5 0 50 6.80 [.0].870 [.0].95 [.0].005 [5.5].0 [.0].00 [5.5].70 [.0].00 [5.0].80 [5.0].55 [9.0].969 [50.0].07 [5.0].6 [60.0].677 [68.0].89 [8.0].66 [9.0] C.80 [6.0].970 [50.0].50 [6.0].600 [66.0].950 [75.0].0 [8.0].90 [00.0].50 [5.0] D.80 [.0].80 [.0].985 [5.0].985 [5.0].080 [7.5].080 [7.5].985 [5.0].06 [7.0].590 [0.5].60 [.0].855 [7.0].885 [8.0].0 [5.0].50 [5.6].90 [60.5].590 [66.0] M F.0 [5.].69 [55.0].8 [6.0].5 [6.9].89 [7.9].860 [7.6].7 [85.6].68 [9.9] Numbers in [ ] are in mm or for metric units [CTx5]. DIMNSIONS G.580 [65.5].60 [66.5].05 [77.0].065 [78.0].60 [89.0].570 [9.0].00 [07.0].590 [7.0] H.8 [9.0].8 [9.0].8 [9.0].8 [9.0].8 [9.0].8 [9.0].07 [.0].07 [.0] J.50 [8.].60 [.] [.5].890 [8.0].0 [57.0].560 [65.0].50 [80.0].660 [9.0] J MOUNTING RCKTS INWRD K.95 [.0]. [8.5].70 [7.].58 [0.].87 [7.6].90 [55.7].577 [65.5].055 [77.6] L.90 [0.0].50 [.5].50 [.5].90 [.5].60 [6.0].670 [7.0].850 [.5].000 [5.5] M.05 [.7].0 [.0].0 [.0].5 [.].6 [.].79 [.5].09 [5.].50 [6.] N.95 [7.5].0 [8.0].70 [9.5].90 [0.0]. [0.5].9 [.0].5 [.5].570 [.5] P #0 [M5] #0 [M5] / [M6] / [M6] / [M6] / [M6] 5/6 [M8] 5/6 [M8] CYLINDR FULCRUM PIN KIT Cylinder Fulcrum Pin Kit replacement for base pivot or for use with PHD cylinder pivot. Pin is rite Zinc plated. Retaining rings supplied. [mm] /6 0/5 /0 50/6.0 [8.5].550 [9.5].0 [.5].690 [.0] DIMNSIONS ØC.00.96 [.0] [5.0].70.5 [.0] [6.0].90.9 [8.0] [0.0].970.7 [50.0] [.0] ØD.5 [.0].56 [.0].7 [7.0].5 [9.0] KIT: CTxx, CTx5x IMPRIL/MTRIC 600-60- 60-60- Numbers in [ ] are in mm or for metric units [CTx5]. Ø D Ø C - (800) 6-85 www.phdinc.com/cts ll dimensions are reference only unless specifically toleranced. CT-0
PPLICTIONS: SRIS CTS COMPCT GUID ROD CYLINDRS ST PRCTICS FOR MXIMUM CYLINDR LIF Maximum cylinder life can be achieved by using the cylinder to provide power and motion while externally stopping any attached loads. Shown below are examples of how to apply the Series CTS Cylinder. PPLICTION # - TTCHD LOD (WITH INTRNL SHOCK PDS) When attached loads cannot be stopped externally, optional internal shock pads are required for maximum cylinder life. It is also XTNSION recommended that flow controls are used to regulate the velocity of the load and limit the kinetic energy at end of stroke. RTRCTION PISTON IMPCTS ON PHD SHOCK PDS TTCHD LOD TTCHD LOD PPLICTION # - TTCHD LODS XTRNLLY STOPPD (WITHOUT INTRNL SHOCK PDS) Shock pads are not required if an attached load is externally stopped to prevent piston from contacting the head and/or cap. XTRNL STOP XTNSION TOOLD STOP RTRCTION PISTON DOS NOT IMPCT HD OR CP TTCHD LOD XTRNL STOP LOD IS XTRNLLY STOPPD PRIOR TO PISTON IMPCTING NDS OF CYLINDR NOT: XMPL SHOWN IS CTxD UNIT TTCHD LOD PPLICTION # - UNTTCHD LODS (WITHOUT INTRNL SHOCK PDS) Shock pads are not required on units with unattached loads. XTNSION RTRCTION UNTTCHD LOD UNTTCHD LOD CT-0 (800) 6-85 www.phdinc.com/cts -
PPLICTIONS: SRIS CTS COMPCT GUID ROD CYLINDRS PPLICTION XMPLS This application uses a Series R Rotary ctuator, Series CTS Guide Rod Cylinder, and a Series 90 Gripper to provide a lift, turn, and grip motion. The compact size of these components makes them ideal for applications with limited space and handling of small parts. This pick and place example uses a Series SD Slide to move a Series CTS Guide Rod Cylinder and Series 90 Gripper. The Series CTS Guide Rod Cylinder is attached to the Series SD Slide using mounting brackets. The Series SD Slide provides outstanding stability and is also offered with shock absorbers for smooth, accurate travel. Using two Series CTS Guide Rod Cylinders and a Series 90 Gripper, this illustration demonstrates a simple way to move an object from point to point. vertical Series CTS Cylinder and a horizontal Series CTS Cylinder provide a lift and extend motion, while the Series 90 Gripper grasps and releases the object in its desired location. This illustration demonstrates a Series CTS Guide Rod Cylinder vertically flush mounted. The Series CTS Guide Rod Cylinder provides a lift and extend motion within an assembly line. Thru and threaded holes provide easy cylinder mounting in limited spaces. - (800) 6-85 www.phdinc.com/cts CT-0
CYLINDRS MDIUM DUTY, HVY DUTY, ND NON-ROTTING ROD INDX: Series, V, HV /", ", & -/8" ore Pages C- to C-7 Series V, HV -/8" ore Pages C-9 to C- C xtremely Wide Variety of Styles and Options, Field Repairable Tie Rod Construction Cylinders Series, V, HV Hydraulic or Pneumatic ir/oil Tandem ir/oil Tandem Pages C- to C-5 ack-to-ack Pages C-6 to C-9 Three Position Pages C-0 to C- Spherical Mount Pages C- to C-7 Series, L, H, S /", -/8", & -/8" ore Pages C-8 to C- Series NPG, NHG, NG, NHG -/8" & -/8" ore Pages C- to C-5 ngineering Data Pages C-6 to C-8 Options Pages C-9 to C-7 Cleanroom Cylinder Page C-8 ack-to-ack Series V, HV, -/8" ore Three Position CT-0 C- (800) 6-85 www.phdinc.com/products/cylinders
ORDRING DT: SRIS, V, HV; /", ", -/8", -/8" C TO ORDR SPCIFY: Series, Mounting Style, ore Size, Stroke, Port Control, and any Options. lso specify rod diameter if non-standard. Rod couplings and mounting attachments must be ordered separately. V HV SRIS - 50 psi ir - 500 psi Hyd. - 50 psi ir (Series not available in -/8" ore.) For use with -/8" bore, Trunnion Mount only. SIZ /" /" Std. Rod Dia. /-8 Thread " 5/6" Std. Rod Dia. 5/6- Thread -/8" /8" Std. Rod Dia. /8- Thread -/8" /" Std. Rod Dia. /8- Thread STNDRD STROK LNGTHS /", ", -/8" SIZS /" to 5" in /" increments -/8" SIZ /" to 6" in /" increments For Longer Lengths, Consult PHD D DR DC R CUSHION OR SHOCK PD - Cushions on both ends - Cushion on rod end - Cushion on cap end - Shock Pads on both ends - Shock Pad on rod end - Shock Pad on cap end C (Cushions, Shock Pads, and Spring Return are not available on the same end of cylinder. Shock Pads and /", ", and -/8" Cushions not available on Series HV.)! Options may affect unit length. See unit dimension and options pages for adders. OVRSIZ ROD To be specified only when using a non-standard diameter. Rod diameters available are shown on page C-. SC V F X x - P - D /8 ROD G-M-V SC SR SPRING RTURN - Spring on cap end - Spring on rod end (Strokes available in /" increments up to 6 ".) See option pages. and/or DOUL ROD ND D - Double Rod nd Cylinders PROXIMITY SWITCH MOUNTING RCKTS SRIS V, HV /" " -/8" -/8" SIZ NO. - - - - See Switches and Sensors section for complete ordering information. F R T RF CF *L *P **K **TR RR RC RRC MOUNTING STYL - Foot Mount, C'bored thru holes - ottom Mount, Tapped holes in head and cap - Rod Mount, Tapped holes on front face of head - Thread Mount, Threaded snout on head (shipped with mounting nut) - Rod nd Flange - Cap nd Flange - Pilot Mount, Threaded snout and pilot diameter on head (shipped with mounting nut) - Pivot Mount, Pivot on cap - Clevis Mount, Clevis on cap - Trunnion Mount - Tierod Mount, Tierods extend out rod end - Tierod Mount, Tierods extend out cap end - Tierod Mount, Tierods extend out both ends * vailable on /", ", and -/8" ore only ** vailable on -/8" ore only PORT CONTROL Notes: ) For double rod cylinders, rod end options will be applied to both ends of cylinder. ) For double rod cylinders, -_K extension will be applied to one end only (head end/primary mounting end). UILT-IN MTR OUT FLOW CONTROL VLV P - Flow control both ends PR - Flow control on head end PC - Flow control on cap end F G I H7 J _K L M N Q R T U V W Y Z OPTIONS - Stroke djustment, /" of adjustment standard (not available on Series HV) - Magnetic Piston for PHD Hall ffect Switches (not available on Series ) - # Rod nd, Standard on /", ", -/8" ore (See page C-) (See Note ) - # Rod nd, Standard on -/8" ore (See page C- for dimensions) (See Note ) - # Rod nd, Female thread on rod (See page C- for dimensions) (See Note ) - Rodlok (Rod clamping device installed. Not available with Z or on HV. See option page.) - #X Rod nd, Twice as long as standard thread (See page C- for dimensions) - xtra Rod xtension, in /8" increments (See page C-) (See Note ) - Coarse Thread Rod nd (See page C- for dimensions) (See Note ) - Magnetic Piston for PHD Reed Switches (not applicable on Series ) - Plain Rod nd (See page C- for dimensions) (See Note ) - Port in Position #, must be specified if required with mounting style F ( F mounting tab on cap end) - Ports in Position # - Ports in Position # ( F mounting tab on cap end) - Ports in Position # - Fluoro-lastomer Seals - Close Tolerance Stroke, ±.005" stroke length - S Ports (Series HV Only) /,, -/8" ore (Consult Factory for S Ports on -/8" ore) - lectroless Nickel Plate all ferrous parts excluding Rod nds Marked options provide additional cylinder flexibility, but may alter the dimensions. C- (800) 6-85 www.phdinc.com/av CT-0
C MDIUM DUTY CYLINDRS /", ", -/8" SRIS V SRIS HV SRIS SRIS SPCIFICTIONS V HV ROD SLS Single lock Vee () lock Vee Single lock Vee with ack-up Ring PISTON SLS () lock Vee () lock Vee () Quad Seal with ack-up Ring ROD WIPR PTF Rod Wiper PISTON ROD Stainless ROD USHINGS ronze CYLINDR RRL Hardcoated luminum ND CPS Zinc Plated Steel lloy PORTS /8" NPT LURICTION Lubricated for Non-Lube ir WORKING PRSSUR 50 psi ir Max. 500 psi Hyd. Max. 50 psi ir Max. STNDRD STROKS /" to 5" in /" Increments Longer Strokes vailable, Consult PHD OPTIONS Port Controls, Cushions, Shock Pads, Magnetic Pistons, Fluoro-lastomer Seals, S Ports FORC TL FORC (lb)/psi DIRCTION /" " -/8" PUSH..785.995 PULL.9.709.88 Consult PHD for your special applications. CT-0 (800) 6-85 www.phdinc.com/av C-
DIMNSIONS: SRIS V; /", ", -/8" SIC CYLINDR DIMNSIONS SQ W.65.65 + STROK.50.5 + STROK X /8 NPT FT THRD C RM DI D WRNCH FLT.50 + STROK (MS9) R (MR) X NT THRD X RT THRD TN D SQ XT SN + STROK RM +.000 -.00 DI CF (MF) X.9 DI THRU.875 + STROK RF (MF) X.9 DI THRU.875 + STROK.5 R R TF UF F (MS8) S NOT L (MNR) X C'D HOLS FOR D SHCS DN X.50 SD + STROK TF UF RM +.000 -.00 DI F (MS8) - WITH PORT CONTROL ON CP ND (-Q or -T without Port Control) T (MN) DN X C'D HOLS FOR D SHCS.65 X.50.5 + STROK.50 SD + STROK RM +.000 -.00 DI ZG + STROK KM THRD KM THRD ZG + STROK.75 P (MP) M W.5 CD DI THRU.5 RD M W.5 INCOMPLT THRD.06 + STROK.8. W SIZ M /.65.65 -/8.875 D CD.50.000.75.5.75 D /6 / 5/6 D DN #8.65 #0.875 #0.000 ll standard rod ends have four wrench flats (two wrench flats with I option). W.000.50.75.75.75 FT /-8 5/6- /8- KM NT 5/8-8 8- x.8 DP /-6 0- x.5 DP - 0- x.5 DP LTTR DIMNSION RM RM.65.687.8 R.875.000.06 RT 8- x.5 DP 8- x.5 DP 0- x.5 DP SD SD.8..50.50 PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH CUSHION SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD N DDITIONL STROK LNGTH TO (+ STROK) DIMNSIONS ( x STROK) F (MS8) MTG: /" UNITS ORDRD WITH N OVRSIZ PISTON ROD WILL HV MTG. TS ON TH HD ND. CONSULT PHD FOR DIMNSIONL INFORMTION. OVRSIZ RODS: S PG C- FOR OVRSIZ ROD SPCIFICTIONS. SN.8 TF TN.65.875.875.000.000 UF W.000.56.75.88.9 W.875.875.5 X XT.56.56.65.65.65.65 ZG.5.5.75 C- (800) 6-85 www.phdinc.com/av ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS HV; /", ", -/8" SIC CYLINDR DIMNSIONS SQ W.65.875 + STROK.50.75 + STROK X /8 NPT FT THRD RM DI D WRNCH FLT.50 + STROK C (MS9) X NT THRD R (MR) X RT THRD TN D SQ XT SN + STROK RM +.000 -.00 DI CF (MF) X.9 DI THRU.5 + STROK RF (MF) X.9 DI THRU.875 + STROK.5 R R TF UF F (MS8) S NOT X C'D HOLS FOR D SHCS.50 TF UF RM +.000 -.00 DI.65.50 F (MS8) - WITH PORT CONTROL ON CP ND.75 + STROK DN X SD + STROK DN X C'D HOLS FOR D SHCS X.50 SD + STROK.75 L (MNR) T (MN) RM +.000 -.00 DI ZG + STROK KM THRD KM THRD ZG + STROK P (MP) M W.5 CD DI THRU.5 RD M W.5 INCOMPLT THRD SIZ M /.65.65 -/8.875 D CD.50.000.75.5.75 D /6 / 5/6 D DN #8.65 #0.875 #0.000. + STROK.8. ll standard rod ends have four wrench flats (two wrench flats with I option). W.000.50.75.75.75 FT /-8 5/6- /8- KM NT 5/8-8 8- x.8 DP /-6 0- x.5 DP - 0- x.5 DP LTTR DIMNSION RM RM.65.687.8 R.875.000.06 RT 8- x.5 DP 8- x.5 DP 0- x.5 DP W SD SD.8..50.50 PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH CUSHION SPRING RTURN: DD N DDITIONL STROK LNGTH TO (+ STROK) DIMNSIONS ( x STROK) F (MS8) MTG. : /" UNITS ORDRD WITH N OVRSIZ PISTON ROD WILL HV MTG. TS ON TH HD ND. CONSULT PHD FOR DIMNSIONL INFORMTION. OVRSIZ RODS: S PG C- FOR OVRSIZ ROD SPCIFICTIONS. SN.8 TF TN.65.875.875.000.000 UF W.000.56.75.88.9 W.875.875.5 X XT.8.8.875.875.875.875 ZG.5.5.75 ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/av C-5
DIMNSIONS: SRIS ; /", ", -/8" SIC CYLINDR DIMNSIONS SQ W.65.5 + STROK.50.5.000 + STROK X /8 NPT FT THRD C RM DI D WRNCH FLT + STROK (MS9) X NT THRD R (MR) X RT THRD TN D SQ CF (MF) X.9 DI THRU XT SN + STROK.75 + STROK RF (MF) RM +.000 -.00 DI X.9 DI THRU.75 + STROK.5 R R TF UF.50 TF UF RM +.000 -.00 DI.65.50 F (MS8) S NOTS X C'D HOLS FOR D SHCS F (MS8) - WITH PORT CONTROL ON CP ND.65 + STROK DN X SD + STROK DN X C'D HOLS FOR D SHCS X.50 SD + STROK.75 L (MNR) T (MN) RM +.000 -.00 DI.65 + STROK KM THRD KM THRD.65 + STROK.65.875.5.65.875.5 INCOMPLT THRD P (MP).50 DI THRU.5 RD.56 + STROK.8. W SIZ / -/8 D.000.5 D D /6 #8 / #0 5/6 #0 DN.65.875.000 ll standard rod ends have four wrench flats (two wrench flats with I option). W.000.50.75.75.75 FT /-8 5/6- /8- LTTR DIMNSION KM NT R RM RM 5/8-8 8- x.8 DP.65.687 /-6 0- x.5 DP.875.8 /-6 0- x.5 DP.000.8 RT 8- x.5 DP 8- x.5 DP 0- x.5 DP SD SD..8.50.50 PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH CUSHION SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD N DDITIONL STROK LNGTH TO (+ STROK) DIMNSIONS ( x STROK) F (MS8) MTG.: /" UNITS ORDRD WITH N OVRSIZ PISTON ROD WILL HV MTG. TS ON TH HD ND. CONSULT PHD FOR DIMNSIONL INFORMTION. OVRSIZ RODS: S PG C- FOR OVRSIZ ROD SPCIFICTIONS. SN..50.50 TF TN.65.875.875.000.000 UF W.000.56.75.88.9 X.56.65.65 XT.56.65.65 C-6 (800) 6-85 www.phdinc.com/av ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS D DOUL ROD; /", ", -/8" SIC CYLINDR DIMNSIONS SQ W OTH NDS.65 ZR + ( x STROK).50 V OTH NDS P + STROK.65 RM DI FT THRD OTH NDS D WRNCH FLT OTH NDS L + STROK X /8 NPT C (MS9) X NT THRD R (MR) X RT THRD TN D SQ XT SN*+ STROK *" ND -/8" : WITH PORT POSITION # DD, 06" WITH PORT POSITION # OR # & PORT CONTROLS DD.06" F (MS8) S NOT X C D HOLS FOR D SHCS RF (MF) RM +.000 -.00 DI X.9 DI THRU Z + ( x STROK).5 DN DF U R.75 X SD + STROK.50 TF UF RM +.000 -.00 DI.50.65 L (MNR) RM +.000 -.00 DI KM THRD ZG + ( x STROK) T (MN) KM THRD ZG + ( x STROK) M.5 M W W ll standard rod ends have four wrench flats (two wrench flats with I option)..5 INCOMPLT THRD SIZ / -/8 M.65.65.65 KM 5/8-8 /-6 /-6 L.000.000.000 SIZ / -/8 P.000.000.000 RM.687.8.8 D.000.5 D /6 / 5/6 D #8 #0 #0 SRIS D CYLINDRS LTTR DIMNSION SD SN V.06.56.5.000.5.000.5 DF DN.75.65.875.875.000 W.875.875.875.000.75 X XT.56.56.65.65.65.65 DIMNSIONS COMMON TO LL SRIS LTTR DIMNSION FT NT RM /-8 8- x.8 DP.65 5/6- /8- Z.000.000.000 ZG.50.50.50 0- x.5 DP 0- x.5 DP ZR R.875.000 SIZ / -/8 RT TF TN 8- x.5 DP 8- x.5 DP.65.875.875 0- x.5 DP.000.000 SRIS DHV CYLINDRS LTTR DIMNSION SIZ M KM L P RM SD SN V W X XT Z ZG ZR /.65 5/8-8.687.65 /-6.8.56.06.75.875.000.75.875.8.8.000.875.875.000 -/8.875 -.06.000.75.5.875.875.50 PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH CUSHION SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD N DDITIONL STROK LNGTH TO LL (+ STROK) DIMNSIONS ( x STROK) F (MS8) MTG: /" UNITS ORDRD WITH N OVRSIZ PISTON ROD WILL HV MTG. TS ON TH HD ND. CONSULT PHD FOR DIMNSIONL INFORMTION. OVRSIZ RODS: S PG C- FOR OVRSIZ ROD SPCIFICTIONS. U.5.50 UF.000.75 W.56.88.9 SRIS DV CYLINDRS LTTR DIMNSION M KM L P RM SD SN V W X XT Z ZG ZR.65 5/8-8.687.65 /-6.8.56.06.5.875.000.5.875.56.56.50.65.65.50.875 -.06.000.5.5.65.65.000.50 ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/av C-7
C NOTS C-8 (800) 6-85 www.phdinc.com/av CT-0
C MDIUM DUTY CYLINDRS -/8" SRIS V, HV SRIS SPCIFICTIONS V HV ROD SLS Single lock Vee Single lock Vee with ack-up Ring PISTON SLS () lock Vee () lock Vee with ack-up Ring ROD WIPR Urethane Wiper/Seal PISTON ROD 00,000 Minimum Yield lloy ROD USHING ronze CYLINDR RRL Hardcoated luminum ND CPS Zinc Plated Steel lloy PORTS /" NPT LURICTION Permanently Lubricated for Non-Lube ir WORKING PRSSUR 50 psi ir Max. 500 psi Hyd. Max. STNDRD STROKS /" to 6" in /" Increments OPTIONS Port Controls, Cushions, Shock Pads, Magnetic Pistons, Fluoro-lastomer Seals FORC TL FORC (lb)/psi DIRCTION -/8" PUSH.85 PULL.89 CT-0 (800) 6-85 www.phdinc.com/av8 C-9
DIMNSIONS: SRIS V, HV; -/8" SIC CYLINDR DIMNSIONS.875 SQ.9.765 + STROK.50.8.0.8 + STROK X / NPT C.50 DI /8- THRD 7/6 WRNCH FLT ROD DI.75.8 + STROK.688.65 (MS) X /-8 THRD x.75 DP R (MR) X /-8 THRD x.75 DP.75 SQ.06.5 + STROK CF (MF) X.8 DI THRU.8 + STROK RF (MF) X.8 DI THRU.87 + STROK.5.7.50.875.50.875 F (MS) T (MN).000.65.5 X.8 DI THRU.75 -/- THRD.7...06.5 + STROK 5.05 + STROK.656...688 F (MS) - WITH PORT CONTROL & CUSHION ON CP ND TR (MT).000.65.5 X.8 DI THRU 5.5 + STROK.75..75.06.8 + STROK DI OTH SIDS.000 K (MP) DI THRU.06..687 RD.000.65.8 + STROK.50 DI RR (MX) RC (MX) X /-8 THRD CH MTG STYL.688 X DIMNSION SPCIFY WHN ORDRING MIN / (.75 + STROK) MX RC (MX) MTG.65.75 SQ.875 + STROK 5.5 + STROK.56.8.5 RRC (MX) INCLUDS RR & RC MTG. ll standard rod ends have four wrench flats (two wrench flats with I option). PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF CUSHIONS SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD N DDITIONL STROK LNGTH TO (+ STROK) DIMNSIONS ( x STROK) OVRSIZ RODS: S PG C- FOR OVRSIZ ROD SPCIFICTIONS..65 RR (MX) MTG C-0 (800) 6-85 www.phdinc.com/av8 ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS DV, DHV DOUL ROD ND;-/8" SIC CYLINDR DIMNSIONS.875 SQ.9 OTH NDS 5.875 + ( x STROK).50.8 OTH NDS.0.8 + STROK.50 DI /8- THRD OTH NDS 7/6 WRNCH FLT OTH NDS ROD DI OTH NDS.75 + STROK.75 X /NPT.65 C (MS) X /-8 THRD x.75 DP R (MR) X /-8 THRD x.75 DP.75 SQ.06 + STROK F (MS) X.8 DI THRU RF (MF) X.8 DI THRU.50.875.5.65.5.75.06.. + STROK.000..688 T (MN) -/- THRD 6.5 + ( x STROK).656 TR (MT) DI OTH SIDS.000 RR (MX).06..000.65.5 + STROK /-8 THRD X W/RR (MX) MTG 8X W/RRC (MX) MTG.687 X DIMNSION SPCIFY WHN ORDRING MIN / (.75 + STROK) MX.75 SQ RRC (MX) THRDD TIROD ON OTH NDS.65 RR (MX) MTG ll standard rod ends have four wrench flats (two wrench flats with I option). PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF CUSHIONS SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD N DDITIONL STROK LNGTH TO LL (+ STROK) DIMNSIONS ( x STROK) OVRSIZ RODS: S PG C- FOR OVRSIZ ROD SPCIFICTIONS. ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/av8 C-
ORDRING DT: SRIS TD IR/OIL TNDM /", ", -/8", -/8" TO ORDR SPCIFY: Series, Mounting Style, ore Size, Stroke, and Options. CYLINDR SRIS TD - 50 psi ir TD SRIS TD PROXIMITY SWITCH MOUNTING RCKTS /" " -/8" -/8" SIZ NO. - - - - See Switches and Sensors section for complete ordering information. SIZ /" /" Rod Dia. /-8 Thread " 5/6" Rod Dia. 5/6- Thread -/8" /8" Rod Dia. /8- Thread -/8" /" Rod Dia. /8- Thread M V F -/8 x - F R T RF CF *L *P **K MOUNTING STYL - Foot Mount, C'bored thru holes - ottom Mount, Tapped holes in head and cap - Rod Mount, Tapped holes on front face of head - Thread Mount, Threaded snout on head (shipped with mounting nut) - Rod nd Flange - Cap nd Flange - Mount, Threaded snout and pilot diameter on head (shipped with mounting nut) - Pivot Mount, Pivot on cap - Clevis Mount, Clevis on cap * vailable on /", ", and -/8" ore only ** vailable on -/8" ore only C OPTIONS - Magnetic Piston for PHD Hall ffect Switches - Magnetic Piston for PHD Reed Switches - Fluoro-lastomer Seals X-M STNDRD STROK LNGTHS /", ", -/8" SIZS /" to 5" in /" increments -/8" SIZ /" to 6" in /" increments For Longer Strokes, Consult PHD. X - C - TNDM OPTION Crossover Tube must be specified to receive the unit with Crossover Tube and Fittings filled with oil for use as ir/oil Tandem (crossover tube only) includes -X (above with the reservoir plumbed to the head end.) For use as ir/oil crossover with reservoir PORT CONTROL UILT-IN MTR OUT FLOW CONTROL VLV Standard on all Series TD Cylinders C- (800) 6-85 www.phdinc.com/td CT-0
SRIS TD TNDM WITH -C OPTION /", ", -/8", -/8" OPRTING PRINCIPL (Shown with Tandem -C option) Cutaway depicts a -/8" ore with -C option. The tandem cylinder consists of a hydraulic cylinder coupled with an air cylinder through a common piston rod. The unit is air powered while the hydraulic portion serves as a control medium; the oil being metered from one side of the piston to the other through a crossover tube (-X option) and built-in Port Control valves. The tandem cylinder provides close, smooth control of piston rod speed even with changing external loads. It is very effective in the lower speed ranges where air cylinders easily chatter due to seal friction and compressible air. reservoir is recommended in conjunction with the hydraulic section of the tandem cylinder when -X is ordered, or order -C to include reservoir. This is especially important in applications having relatively rapid continuous cycling. The oil temperature will in this case increase with resulting expansion. decrease in volume will occur during idle time. To avoid pulsing due to pressure changes in the hydraulic section during operation, the reservoir must be subjected to constant air pressure (0 psi). C SPCIFICTIONS /", ", -/8" -/8" ROD SLS lock Vee PISTON SLS () lock Vee per Piston ROD WIPR PTF Urethane/Wiper Seal PISTON ROD Stainless Steel Chrome Plated High Strength Steel ROD USHINGS ronze CYLINDR RRLS Hardcoated luminum ND CPS Zinc Plated lloy Steel PORTS /8 NPT / NPT LURICTION Permanently Lubricated for Non-Lube ir WORKING PRSSUR 50 psi ir Max. STNDRD STROKS /" to 5" in /" Increments /" to 6" in /" Increments Longer Strokes vailable, Consult PHD. TNDM FLUID S Weight Oil (Viscosity at 00 F is 58. SSU at 50 is 5..) RSRVOIR (OPTIONL) luminum Caps with Fiberglass Tube PRSSUR ON RSRVOIR 0 psi Recommended FORC TL FORC (lb)/psi DIRCTION /" " -/8" -/8" PUSH..785.995.85 PULL.9.709.88.89 Consult PHD for Maintenance Videos. CT-0 (800) 6-85 www.phdinc.com/td C-
DIMNSIONS: SRIS TD IR/OIL TNDM; /", ", -/8" SIC CYLINDR DIMNSIONS OPTIONL: RSRVOIR C.875 W.65.5.50 OPTIONL: CROSSOVR TU X /8 NPT SQ RM DI FT THRD D WRNCH FLT.5.5.50.50.5.5 + STROK.50 + STROK 5.000 + ( x STROK) 5.75 + ( x STROK) (MS9) X NT THRD R (MR) X RT THRD TN D SQ XT SN + ( x STROK) RM +.000 -.00 DI CF (MF) X.9 DI THRU 5.65 + ( x STROK) RF (MF) X.9 DI THRU 5.65 + ( x STROK).5 R R TF UF.50 TF UF.65.50 F (MS8) X C'D HOLS FOR D SHCS P (MP) CD DI THRU.5 RD DN X SD + ( x STROK) 5.8 + ( x STROK).8. W L (MNR) RM +.000 -.00 DI KM THRD ZG + ( x STROK) T (MN) KM THRD ZG + ( x STROK) M W.5 M W.5 INCOMPLT THRD ll standard rod ends have four wrench flats (two wrench flats with I option). SIZ M D CD D D DN W /.65.50 /6 #8.65.000.50.65.000.75 / #0.875.75.75 -/8.875.5.75 5/6 #0.000.75 PORT POSITIONS: INDICTD Y CIRCLD NUMRS FT /-8 5/6- /8- KM NT 5/8-8 8- x.8 DP /-6 0- x.5 DP - 0- x.5 DP LTTR DIMNSION RM RM.65.687.8 R.875.000.06 RT 8- x.5 DP 8- x.5 DP 0- x.5 DP SD.56 SN.56 TF TN.65.875.875.000.000 UF W.000.56.75.88.9 W.875.875.5 X XT.56.56.65.65.65.65 ZG 5.875 5.875 6.5 C- (800) 6-85 www.phdinc.com/td ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS TD IR/OIL TNDM; -/8" SIC CYLINDR DIMNSIONS OPTIONL: RSRVOIR OPTIONL: CROSSOVR TU.50.9.8.50 X / NPT C.875 SQ.50 DI /8 THRD 7/6 WRNCH FLT ROD DI.....0.8 + STROK.06.8 + STROK 8. + ( x STROK) 9.65 + ( x STROK).65 (MS) X /-8 THRD x.75 DP R (MR) X /-8 THRD x.75 DP.75 SQ CF (MF) X.8 DI THRU.06 7.65 + ( x STROK) 9. + ( x STROK) RF (MF) X.8 DI THRU.5.50.875.50.875 F (MS).000.65.5 X.8 DI THRU.75.06.. 7.65 + ( x STROK). T (MN).000..688 9.55 + ( x STROK).656.000.65.06. 7.97 + ( x STROK) K (MP) DI THRU.687 RD.50 DI 8.75 + ( x STROK) 9.65 + ( x STROK).56.5 ll standard rod ends have four wrench flats (two wrench flats with I option). PORT POSITIONS: INDICTD Y CIRCLD NUMRS ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/td C-5
TO ORDR SPCIFY: Series, Type, Mounting Style, ore Size, Cylinder Stroke, Cylinder Stroke, and Options. V PROXIMITY SWITCH MOUNTING RCKTS SRIS SIZ NO. V, HV /" " -/8" -/8" - - - - See Switches and Sensors section for complete ordering information. -/8 x x - P-M C ORDRING DT: CK-TO-CK; /", ", -/8", -/8" V HV CYLINDR SRIS - 50 psi ir - 500 psi Hyd. - 50 psi ir (Series not available in -/8" ore.) TYP - ack to ack Cylinder SIZ /" /" Rod Dia. /-8 Thread " 5/6" Rod Dia. 5/6- Thread -/8" /8" Rod Dia. /8- Thread -/8" /" Rod Dia. /8- Thread! Options may affect unit length. See unit dimension and options pages for adders. STNDRD STROK CYLINDR /" to 6" strokes available STNDRD STROK CYLINDR /" to 6" strokes available F R T RF *L MOUNTING STYL - Foot Mount, C'bored through holes - ottom Mount, Tapped holes in head and cap - Rod Mount, Tapped holes on front face of head - Thread Mount, Threaded snout on head (shipped with mounting nut) - Rod end flange - Pilot Mount, Threaded snout and pilot diameter on head (shipped with mounting nut) * vailable on /", ", and -/8" ore only D M P V OPTIONS - Shock Pads on both ends of each cylinder (not available on Series HV) - Cushion on both ends of each cylinder (not available on Series HV /", ", and -/8" sizes) - Magnetic Pistons on both cylinders for PHD Hall ffect Switches (not available on Series ) - Magnetic Pistons on both cylinders for PHD Reed Switches (not available on Series ) - Port Controls on both ends of each cylinder - Fluoro-lastomer Seals C-6 (800) 6-85 www.phdinc.com/av CT-0
SRIS, V, HV CK-TO-CK /", ", -/8", -/8" For use where four rod positions are required and a double rod construction is acceptable. y sequencing the unit with two different stroke cylinders, the overall length from rod end to rod end will produce four positive repeatable lengths. C SRIS SPCIFICTIONS V HV ROD SLS Single lock Vee () lock Vee with ack-up Ring Single lock Vee (One Rod Seal with ack-up on -/8" ore) PISTON SLS () lock Vee () lock Vee with ack-up Ring () Quad-X Type ROD WIPR /,, -/8" PTF Rod Wiper -/8" Urethane Wiper/Seal PISTON ROD /,, -/8" Stainless -/8" 00,000 psi Minimum Yield lloy ROD USHINGS ronze CYLINDR RRL Hardcoated luminum ND CPS Zinc Plated Steel lloy PORTS NPT LURICTION Permanently Lubricated for Non-Lube ir WORKING PRSSUR 50 psi ir Max. 500 psi Hyd. Max. 50 psi ir Max. STNDRD STROKS /,, -/8" /" to 5" in /" Increments -/8" /" to 6" in /" Increments Longer Strokes vailable, Consult PHD OPTIONS Port Controls, Cushions, Shock Pads, Magnetic Pistons, Fluoro-lastomer Seals FORC TL FORC (lb)/psi DIRCTION /" " -/8" -/8" PUSH..785.995.85 PULL.9.709.88.89 CT-0 (800) 6-85 www.phdinc.com/av C-7
DIMNSIONS: SRIS, V, HV CK-TO-CK; /", ", -/8" SIC CYLINDR DIMNSIONS SQ W OTH NDS.65 ZR + (STROK CYL + STROK CYL ).50 V OTH NDS P + STROK P + STROK.65 C RM DI FT THRD OTH NDS D WRNCH FLT OTH NDS L + STROK L + STROK X /8 NPT (MS9) X NT THRD R (MR) X RT THRD TN D SQ XT SN + STROK (CYL & CYL ) +.000 RM -.00 DI F (MS8) X C'D HOLS FOR D SHCS RF (MF) X.9 DI THRU Z + STROK (CYL & CYL ).5 DN DF U R.75 X.50 SD + STROK (CYL & CYL ).50 TF UF RM +.000 -.00 DI.65.50 L (MNR) RM +.000 -.00 DI KM THRD ZG + STROK (CYL & CYL ) T (MN) KM THRD ZG + STROK (CYL & CYL ) M W.5 M W.5 INCOMPLT THRD SIZ M KM L /.65 5/8-8.65 /-6 -/8.65 /-6 P.000.000.000 SIZ / -/8 D.000.5 ll standard rod ends have four wrench flats (two wrench flats with I option). D /6 / 5/6 D #8 #0 #0 SRIS CYLINDRS LTTR DIMNSION RM SD SN V W.687.56.06.5.875.8.000.5.875.8.000.5.875 SIZ / -/8 DF DN.75.65.875.875.000 X.56.65.65.000.75 XT.56.65.65 DIMNSIONS COMMON TO LL SRIS LTTR DIMNSION FT NT RM /-8 8- x.8 DP.65 5/6- /8- Z ZG 0- x.5 DP 0- x.5 DP ZR.50.50 50 R.875.000 SRIS HV CYLINDRS LTTR DIMNSION M KM L P RM SD SN V W.65 5/8-8.50.687.65 /-6.50.8.56.06.75.875.000.75.875.875 -.50.06.000.75.5 RT 8- x.5 DP 8- x.5 DP 0- x.5 DP SRIS V CYLINDRS LTTR DIMNSION SIZ M KM L P RM SD SN V W X XT Z ZG ZR /.65 5/8-8.50.687.65 /-6.50.8.56.06.5.875.000.5.875.56.56 5 5 5.50.65.65 5 5 5.50 -/8.875 -.50.06.000.5.5.65.65 5 6.000 5.50 X XT.8.8.875.875.875.875 PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: DD " TO LL (+ STROK) DIMNSIONS OF CYLINDR ND CYLINDR (" TOTL TO OVRLL) SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS OF CYLINDR ND CYLINDR (" TOTL TO OVRLL) TF.875.000 TN.65.875.000 Z ZG ZR 5 6.000 5 5 6.000 5 5 6.50 5 U.5.50 UF W.000.56.75.88.9 C-8 (800) 6-85 www.phdinc.com/av ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS V, HV CK-TO-CK; -/8" SIC CYLINDR DIMNSIONS.875 SQ.9 TYP 9.000 + (STROK CYL + STROK CYL ).50.8 OTH NDS.0.8 + STROK.8 + STROK.0.50 DI /8- THRD OTH NDS 7/6 WRNCH FLT OTH NDS ROD DI OTH NDS.75.8 + STROK.688.688.8 + STROK X / NPT.65 C (MS) X /-8 THRD x.75 DP R (MR) X /-8 THRD x.75 DP.75 SQ.06 6.875 + STROK (CYL & CYL ) F (MS) X.8 DI THRU RF (MF) X.8 DI THRU.5.50.875 T (MN).65.5.75.06.. 6.875 + STROK (CYL & CYL ) -/- THRD.000 9.50 + STROK (CYL & CYL ).656..688.06..000.65 7.50 + STROK (CYL & CYL ) ll standard rod ends have four wrench flats (two wrench flats with I option). PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF CUSHIONS SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS OF CYLINDR ND CYLINDR (" TOTL TO OVRLL) ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/av C-9
ORDRING DT: SRIS, V, HV THR POSITION; /", ", -/8", -/8" C TO ORDR SPCIFY: Series, Type, Mounting Style, ore Size, Cylinder Stroke, Cylinder Stroke, and Options. CUTION: HYDRULIC THR POSITION CYLINDR (HV) MUST VLVD PROPRLY TO PRVNT LOCKING OF FLOW FROM TH CNTR PORT WHN PRSSURIZING TH RR (CP) PORT. FILUR TO DO SO MY RSULT IN N INTNSIFICTION OF PRSSUR IN CYLINDR NUMR CUSING TIROD FILUR. SIZ /" /" Rod Dia. /-8 Thread " 5/6" Rod Dia. 5/6- Thread POSITION FULL XTND POSITION MID-POSITION XTND POSITION FULL RTRCT V HV CYLINDR SRIS - 50 psi ir - 500 psi Hyd. - 50 psi ir (Series not available in -/8" ore.) -/8" /8" Rod Dia. /8- Thread -/8" /" Rod Dia. /8- Thread STNDRD STROK CYLINDR (TOTL STROK) /" to 6" strokes available STNDRD STROK CYLINDR (FROM RTRCT TO MID POSITION) /" to 6" strokes available V R - / x x / - P-M TYP - Three Position Cylinder PROXIMITY SWITCH MOUNTING RCKTS SRIS V, HV /" " -/8" -/8" SIZ NO. - - - - See Switches and Sensors section for complete ordering information. F R T RF CF *L *P **K MOUNTING STYL - Foot Mount, C'bored through holes - ottom Mount, Tapped holes in head and cap - Rod Mount, Tapped holes on front face of head - Thread Mount, Threaded snout on head (shipped with mounting nut) - Rod nd Flange - Cap nd Flange - Pilot Mount, Threaded snout and pilot diameter on head (shipped with mounting nut) - Pivot Mount, Pivot on cap - Clevis Mount, Clevis on cap * vailable on /", ", and -/8" ore only ** vailable on -/8" ore only D M P V! OPTIONS - Shock Pads on full extension and retraction only (not available on Series HV) - Cushion on full extension and retraction only (not available on Series HV /", ", and -/8" sizes) - Magnetic Pistons on both cylinders for PHD Hall ffect Switches (not available on Series ) - Magnetic Pistons on both cylinders for PHD Reed Switches (not available on Series ) - Port Controls on all heads and cap, full extension and retraction only, not on mid-position extension - Fluoro-lastomer Seals Options may affect unit length. See unit dimension and options pages for adders. C-0 (800) 6-85 www.phdinc.com/av CT-0
SRIS, V, HV THR POSITION; /", ", -/8", -/8" Position For use where three rod positions are required. The single rod end starts at full retract, extends to a positive midposition or to full extension. When retracting, the cylinder may return to the midposition for a total of three positive stop linear positions. C Position Position SRIS SPCIFICTIONS V HV ROD SLS Single lock Vee () lock Vee with ack-up Ring Single lock Vee (One Rod Seal with ack-up on -/8" ore) PISTON SLS () lock Vee () lock Vee with ack-up Ring () Quad-X Type ROD WIPR /,, -/8" PTF Rod Wiper -/8" Urethane Wiper/Seal PISTON ROD /,, -/8" Stainless -/8" 00,000 psi Minimum Yield lloy ROD USHINGS ronze CYLINDR RRL Hardcoated luminum ND CPS Zinc Plated Steel lloy PORTS NPT LURICTION Lubricated for Non-Lube ir WORKING PRSSUR 50 psi ir Max. 500 psi Hyd. Max. 50 psi ir Max. STNDRD STROKS /,, -/8" /" to 5" in /" Increments -/8" /" to 6" in /" Increments Longer Strokes vailable, Consult PHD OPTIONS Port Controls, Cushions, Shock Pads, Magnetic Pistons, Fluoro-lastomer Seals FORC TL FORC (lb)/psi DIRCTION /" " -/8" -/8" PUSH..785.995.85 PULL.9.709.88.89 CT-0 (800) 6-85 www.phdinc.com/av C-
DIMNSIONS: SRIS, V, HV THR POSITION; /", ", -/8" SIC CYLINDR DIMNSIONS SQ W.65 ZJ + (STROK CYL + STROK CYL ).50 V P + STROK CYL P + STROK CYL FT THRD C RM DI D WRNCH FLT.50 L + (STROK CYL + STROK CYL ) X /8 NPT (MS9) X NT THRD R (MR) X RT THRD TN D SQ XT SN + STROK (CYL & CYL ) RM +.000 -.00 DI CF (MF) X.9 DI THRU RF (MF) X.9 DI THRU.5 R R F (MS8) TF UF X C'D HOLS FOR D SHCS.50 TF UF.65.50 F (MS8) - WITH PORT CONTROL ON CP ND RM +.000 -.00 DI L (MNR) DN X SD + STROK (CYL & CYL ) RM +.000 -.00 DI ZG + STROK KM THRD (CYL & CYL ) T (MN) DN X C'D HOLS FOR D SHCS KM THRD X SD + STROK (CYL & CYL ) ZG + STROK (CYL & CYL ).75.50 M W.5 M W.5 INCOMPLT THRD P (MP) CD DI THRU XC + STROK (CYL & CYL ).8.5 RD. W ll standard rod ends have four wrench flats (two wrench flats with I option). PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: DD /" TO (+ STROK) DIMNSIONS OF CYLINDR ND CYLINDR FOR CUSHIONS (DD TOTL OF " TO OVRLL LNGTH) SHOCK PDS: DD /" TO (+ STROK) DIMNSIONS OF CYLINDR ND CYLINDR FOR SHOCK PDS (DD TOTL OF /" TO OVRLL LNGTH) SIZ / -/8 M.65.65.65 CD.50.50.50 SIZ / -/8 KM L P P 5/8-8..000.56 /-6..000.56 /-6..000.56 D.000.5 RM.687.8.8 D /6 / 5/6 D #8 #0 #0 DF DN.75.65.875.875.000.000.75 DIMNSIONS COMMON TO LL SRIS LTTR DIMNSION FT NT RM /-8 8- x.8 DP.65 W.50.75.75 5/6- /8- R RT TF 0- x.5 DP.875 8- x.5 DP 8- x.5 DP.875 0- x.5 DP.000 0- x.5 DP.000 TN.65.875.000 U.5.50 UF W.000.56.75.88.9 SRIS CYLINDRS LTTR DIMNSION SRIS V CYLINDRS LTTR DIMNSION SD SD SN V W X XC XT ZG ZJ M CD KM L P P RM SD SD SN V W X XC XT ZG ZJ.875.75.875.5.875.56.5.56.87.687.8..8.5.875.65.5.65.87.687.65.50 5/8-8..06.687.875.75.875.5.875.56 5.5.56 5.87.687.65.75 /-6..06.8.8..8.5.875.65 5.5.65 5.87.687.8..8.5.875.65.5.65.87.687.875.75 -..06.06.8..8.5.5.65 5.5.65 5.7.687 SRIS HV CYLINDRS LTTR DIMNSION SIZ M CD KM L P P RM SD SD SN V W X XC XT ZG ZJ /.65.50 5/8-8..06.687.875.75.875.75.875.8 5.75.8 5.87.97.65.75 /-6..06.8.8..8.75.875.875 5.75.875 5.87.97 -/8.875.75 -..06.06.8..8.75.5.875 5.75.875 5.7.97 C- (800) 6-85 www.phdinc.com/av ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS V, HV THR POSITION; -/8" SIC CYLINDR DIMNSIONS.875 SQ.9.50.8.0 8.65 + (STROK CYL + STROK CYL ).8 + STROK CYL + STROK CYL.50 DI /8- THRD 7/6 WRNCH FLT ROD DI.75..50 7. + (STROK CYL + CYL ).688.65 X / NPT C (MS) X /-8 THRD x.75 DP R (MR) X /-8 THRD x.75 DP.75 SQ.06 6.59 + STROK (CYL & CYL ) CF (MF) X.8 DI THRU 8. + STROK (CYL & CYL ) RF (MF) X.8 DI THRU 8.65 + STROK (CYL & CYL ).5.65.50.875.50.875 F (MS).000 X.8 DI THRU..000..688 F (MS)-WITH PORT CONTROL & CUSHION ON CP ND X.8 DI THRU 8.65 + STROK (CYL & CYL ) T (MN) K (MP).75.65.5 -/- THRD...06 6.65 + STROK (CYL & CYL ).06. 8.55 + STROK (CYL & CYL ).656.000.65 6.97 + STROK (CYL & CYL ) DI THRU RR (MX) RC (MX).65.5 RRC (MX) INCLUDS RR & RC MTG.687 RD.75 SQ..50 DI /-8 THRD X CH MTG STYL.06..75 7. + STROK (CYL & CYL ) RC (MX) MTG.65.65 RR (MX) MTG 7.75 + STROK (CYL & CYL ) 8.65 + STROK (CYL & CYL ).56.8.5 ll standard rod ends have four wrench flats (two wrench flats with I option). PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF CUSHIONS SHOCK PDS: DD /" TO (+ STROK) DIMNSIONS OF CH CYLINDR ND CYLINDR (DD TOTL OF /" TO OVRLL LNGTH) ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/av C-
C ORDRING DT: SRIS S, VS, HVS SPHRICL MOUNT /", ", -/8", -/8" TO ORDR SPCIFY: Series, Mounting Style, ore Size, Stroke, and Options. If Spherical Rod nd is required, specify with Part Number listed. V HV CYLINDR SRIS - 50 psi ir - 500 psi Hyd. - 50 psi ir (Series not available in -/8" ore.) SIZ /" /" Rod Dia. /-8 Thread " 5/6" Rod Dia. 5/6- Thread -/8" /8" Rod Dia. /8- Thread -/8" /" Rod Dia. /-0 Thread D M P V OPTIONS - Shock Pads on both ends of each cylinder - Cushion on both ends of each cylinder (not available on Series HV /", ", and -/8" sizes or on cap end of -/8" ore) - Magnetic Pistons for PHD Hall ffect Switches (not available on Series ) - Magnetic Pistons for PHD Reed Switches (not available on Series ) - Port Controls on both ends - Fluoro-lastomer Seals V S -/8 x - P-D MOUNTING STYL S - Spherical mount on cap end STNDRD STROK LNGTH /" to 6" strokes available Longer Strokes vailable, Consult PHD. Options may affect unit length. See unit dimension and options pages for adders. SPHRICL MOUNT ROD NDS ROD ND THRD SIZ PRT NUMR PROXIMITY SWITCH MOUNTING RCKTS SRIS V, HV /" " -/8" -/8" SIZ NO. - - - -! /" - 8 5/6" - /8" - /" - 0 7-00 7-00 7-00 7-00 See Switches and Sensors section for complete ordering information. C- (800) 6-85 www.phdinc.com/avs CT-0
C SRIS S, VS, HVS SPHRICL MOUNT /", ", -/8", -/8" SRIS SPCIFICTIONS VS HVS S ROD SLS Single lock Vee () lock Vee with ack-up Ring Single lock Vee (One Rod Seal with ack-up on -/8" ore) PISTON SLS () lock Vee () lock Vee with ack-up Ring () Quad Seal ROD WIPR /,, -/8" PTF Rod Wiper -/8" Urethane Wiper/Seal PISTON ROD /,, -/8" Stainless -/8" 00,000 psi Minimum Yield lloy ROD USHINGS ronze CYLINDR RRL Hardcoated luminum ND CPS Zinc Plated Steel lloy MOUNTS Spherical earing PORTS NPT LURICTION Lubricated for Non-Lube ir WORKING PRSSUR 50 psi ir Max. 500 psi Hyd. Max. 50 psi ir Max. STNDRD STROKS /,, -/8" /" to 5" in /" Increments -/8" /" to 6" in /" Increments Longer Strokes vailable, Consult PHD OPTIONS Port Controls, Cushions, Shock Pads, Magnetic Pistons, Fluoro-lastomer Seals FORC TL FORC (lb)/psi DIRCTION /" " -/8" -/8" PUSH..785.995.85 PULL.9.709.88.89 CT-0 (800) 6-85 www.phdinc.com/avs C-5
DIMNSIONS: SRIS S, VS, HVS SPHRICL CP ND; /", ", -/8" LLOWL NGL OF MISLIGNMNT RM DI P + STROK X /8 NPT LLOWL NGL OF MISLIGNMNT C G F F G C DI LL Q DI L + STROK C DI LL O L ZW + STROK.50 N V J O R DI K ±.00 DI K ±.00 DI R DI S NOTS WRNCH FLT VILL ROD ND THRD ll standard rod ends have four wrench flats. SIZ / -/8 /8 7/6 9/6.68.7.06 C.65.78 6.5 F.8..06 G.75.8 J.8.98 LTTR DIMNSION K L L N.5.68 S...56 VS & HVS.75.76.8.50.65 O.75.7 P S.000 VS & HVS Q.75.7.56 R.875.000 RM.65 V S & VS.5 HVS.75 SIZ / -/8 ZW DIMNSION SRIS S SRIS VS.875.75.97.8.06.56 SRIS HVS.65.687.8 ROD SPHRICL ND: SPHRICL ND ON CYLINDR ROD NOT INCLUDD - MUST ORDRD SPRTLY CUSHIONS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH CUSHION SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD N DDITIONL STROK LNGTH TO LL (+ STROK) DIMNSIONS ( x STROK) C-6 (800) 6-85 www.phdinc.com/avs ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS VS, HVS SPHRICL CP ND; -/8" X / NPT LLOWL NGL OF MISLIGNMNT.50 DI.0.8 + STROK LLOWL NGL OF MISLIGNMNT C.65.65.98 DI LL DI.75.688.8 + STROK.65.98 DI LL.656.7.50 5 + STROK.656.5.8.50. DI.50 ±.00 DI.50 ±.00 DI. DI S NOTS / WRNCH FLT.5 VILL ROD ND THRD ll standard rod ends have four wrench flats. ROD SPHRICL ND: ROD SPHRICL ND IS NOT INCLUDD - MUST ORDRD SPRTLY CYLINDR ROD ND: CYLINDR ROD ND WILL HV /-0 THRD CUSHIONS: VILL ON ROD ND ONLY (-DR). CYLINDR LNGTH IS NOT FFCTD SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD N DDITIONL STROK LNGTH TO LL (+ STROK) DIMNSIONS ( x STROK) ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/avs C-7
ORDRING DT: SRIS, L, H, S CYLINDRS C TO ORDR SPCIFY: Series, Mounting Style, ore Size, Stroke, Port Controls, Cushions and Shock Pads, Oversize Rod, and Options. SIZ /" /8" Std. Rod Dia. /-8 Thread DOUL ROD ND L H S SRIS - 50 psi ir - 500 psi Hyd. - 000 psi Hyd. - 5000 psi Hyd. -/8" /" Std. Rod Dia. /8- Thread -/8" 5/8" Std. Rod Dia. 7/6-0 Thread P PR PC UILT-IN MTR OUT FLOW CONTROL VLV - Flow control both ends - Flow control on head end Not available on MT - Flow control on cap end Not available on MT OVRSIZD ROD -/8 and -/8" ore only To be specified only when using a non-standard rod diameter. (See page C-6) D MS -/8 x - P - D - 5/8 ROD - F-M-V MS MS MF MF MT MT MP MR MOUNTING STYL CUSHION OR SHOCK PD OPTIONS - Foot Mount through holes Not available on -/8" and -/8" S Series - ottom Mount, Tapped holes in head and cap - Rod nd Flange - Cap nd Flange - Head Trunnion - Cap Trunnion - Clevis Mount, Cap end with pin - Rod Mount, Tapped holes on front face of head Notes: ) For double rod cylinders, rod end options will be applied to both ends of cylinder. ) For double rod cylinders, -_K extension will be applied to one end only (head end/primary mounting end). PROXIMITY SWITCH MOUNTING RCKTS SRIS, L STNDRD STROK LNGTHS STOCK STROK LNGTHS /" to 6" in /" increments Longer Strokes vailable, Consult Factory. /" -/8" -/8" SIZ NO. -5-6 -7 See Switches and Sensors section for complete ordering information. D DR DC R - Cushions on both ends - Cushion on rod end - Cushion on cap end - Shock Pads on both ends - Shock Pad on rod end - Shock Pad on cap end C (Cushions and Shock Pads are not available on the same end of cylinder. Shock Pads are not available for Hydraulic use.) NOT: S Ports available. Consult PHD for sizes. F I J _K L M N R T U V W Z - Stroke djustment (/" standard) - Magnetic Piston for PHD Hall ffect Switches (Series and L only) - # Rod nd (See page C-6) (See Note ) - # Rod nd, female thread on rod (See page C-6) (See Note ) - #X Rod nd, twice as long as standard thread (See page C-6) (See Note ) - xtra Rod xtensions (See page C-) (See Note ) - Coarse Thread Rod nd (See page C-6) (See Note ) - Magnetic Piston for PHD Reed Switches (Series and L only) - Plain Rod nd (See Note ) - Port in Position - Port in Position - Port in Position - Fluoro-lastomer Seals - Close Tolerance Stroke, ±.005 stroke length - lectroless Nickel Plate all ferrous parts excluding rod ends C-8 (800) 6-85 www.phdinc.com/e CT-0
C SRIS, H, L, S HVY DUTY CYLINDRS /", -/8", -/8" SIZS SRIS SPCIFICTIONS L H S ROD SLS Single lock Vee () lock Vee with ack-up Ring PISTON SLS () lock Vee () lock Vee with ack-up Ring TU SLS O-ring O-ring with ack-up Ring ROD WIPR Urethane Rod Wiper PISTON ROD Hardchrome Plated High Strength Steel 00,000 psi Min. Yield ROD USHING Cast Iron Rod Cartridge CYLINDR RRL Hardcoated luminum Honed Steel ND CPS Zinc Plated Steel TIRODS High Tensile Steel Heat Treated Stainless Steel PORTS NPT LURICTION Permanently Lubricated for Non-Lube ir WORKING PRSSUR 50 psi ir Max. 500 psi Hyd. Max. 000 psi Hyd. Max. 5000 psi Hyd. Max. STNDRD STROKS /" to 6" in /" Increments Longer Strokes vailable, Consult PHD OPTIONS Port Controls, Cushions, Shock Pads, Magnetic Pistons, Fluoro-lastomer Seals, Rod nds, Oversize Rods FORC TL FORC (lb)/psi DIRCTION /" -/8" -/8" PUSH..99.85 PULL..798.78 CT-0 (800) 6-85 www.phdinc.com/e C-9
DIMNSIONS: SRIS, H, L, S CYLINDR; /", -/8", -/8" SIC CYLINDR DIMNSIONS SQ W V.50 Y Z + STROK P + STROK X NPT C RM DI FT THRD D WRNCH FLT MM ROD DI G L + STROK.5 K MS X NT* THRD MR X RT THRD TN D SQ XT SN + STROK +.000 RM -.005 DI MF X F DI THRU ZF + STROK MF X F DI THRU Z + STROK V R R TF UF F TF UF +.000 RM -.005 DI F W MS MT TS US X F DI THRU ST XS SY SU +.000 TD -.00 DI OTH SIDS SY SU SS + STROK MP (CLVIS PIN INCLUDD) MT CD DI THRU XC + STROK L M +.000 TD -.00 DI OTH SIDS MR RD CL C CC DI UT TL XJ + STROK UT TL XG ll standard rod ends have four wrench flats (two wrench flats with I option). SIZ / -/8 -/8 D C.000.75.50.65.65 SIZ SN SS /.88.06 -/8..98 -/8.8.98 ST.8..69 CC CD CL D.000.75.875..75 /.50.5.8 /.65.56.50 /8 SU.50..8 SY.8.06 F. TD TF TL TN TS.98.56.98.65.875.000.875.875.000 F.9.8. UF.75.000 FT /-8 /8-7/6-0 LTTR DIMNSION G K L L.8 0.00.000.88.50.65.75.65..8 LTTR DIMNSION US UT V.75.75.5.000.50.50.000.50 RT 0- X.5 DP /-8 X.50 DP 5/6- X.6 DP PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF CUSHIONS MT (-DR) & MT (-DC) CUSHION NDLS R IN POSITION SHOCK PDS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF SHOCK PDS MS MTG. STYL: NOT VILL ON -/8" & -/8" SRIS S CYLINDRS *MS MTG. STYL: UNITS WITH OPTION -R OR -U WITH/-P. TH NT THRD SIZ ND DPTH WILL RDUCD S FOLLOWS: /" NOT VILL WITH -R OR -U WITH/-P. -/8" NT=0- x.9, -/8" NT=/-8 x.5 OVRSIZ RODS: S PG C-6 FOR OVRSIZ ROD SPCIFICTIONS W.688.000.000 W.56.9.50 M.75.65 MM.75.65 XC XG.875.65 5.06 6.06.8 MR.570.70.90 XJ.8.75.875 NT* 0- X.5 DP /-8 X. DP 5/6- X.50 DP P.88 R.98 RM..50.000.8.65.50 XS XT Y Z ZF.88.65.50.75.688.06.56 5.5 5.75.88.8.98 5.65 5.8 C-0 (800) 6-85 www.phdinc.com/e ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS CYLINDRS; DOUL ROD ND SIC CYLINDR DIMNSIONS SQ W OTH NDS ZR + ( x STROK).50 V OTH NDS Y P + STROK X NPT RM DI FT THRD D WRNCH FLT MM ROD DI G L + STROK G K C MS X NT* THRD MR X RT THRD TN D SQ XT SN + STROK +.000 RM -.005 DI MS TS US X F DI THRU ST XS SY SU SY SU SS + STROK MT UT TL XG +.000 TD -.00 DI OTH SIDS MF X F DI THRU V ZR + ( x STROK) R TF UF +.000 RM -.005 DI F W SIZ / -/8 -/8 D.000.50.65 SIZ SN SS /.88.06 -/8..98 -/8.8.98 ll standard rod ends have four wrench flats (two wrench flats with I option). D..75 /.8 /.56.50 /8 ST.8..69 SU.50..8 SY.8.06 F. F.9.8. FT /-8 /8-7/6-0 LTTR DIMNSION G K L.8 0.00.687.88.50 5.7.65. 6. MM.75.65 LTTR DIMNSION TD TF TL TN TS UF US UT.98.56.98.75.75.75.65.000.000.50.875.000.875.875.000.000 NT* 0- X.5 DP /-8 X. DP 5/6- X.50 DP V.5.50.50 W.688.000.000 P.88..8 W.56.9.50 R.98.50.65 RM RT 0- X.5 DP.000 /-8 X.50 DP.50 5/6- X.6 DP XG XS XT Y.65.88.65.50.06.06.56.8.88.8.98 PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF CUSHIONS MT (-DR) CUSHION NDLS R IN POSITION SHOCK PDS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF SHOCK PDS MS MTG. STYL: NOT VILL ON -/8" & -/8" SRIS S CYLINDRS *MS MTG. STYL: UNITS WITH OPTION -R OR -U WITH/-P. TH NT THRD SIZ ND DPTH WILL RDUCD S FOLLOWS: /" NOT VILL WITH -R OR -U WITH/-P. -/8" NT=0- x.9, -/8" NT=/-8 x.5 OVRSIZ RODS: S PG C-6 FOR OVRSIZ ROD SPCIFICTIONS ZR 5.8 6.8 7. ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/e C-
ORDRING DT: SRIS NPG, NHG, NG, NHG CYLINDRS C TO ORDR SPCIFY: Spring Return, Series, Mounting Style, ore Size, Stroke, and Options. SC SR SPRING RTURN - Spring on cap end - Spring on rod end (Spring Return available on Series NPG Cylinders up to " of stroke in /" increments.) MF MF MT MP MR **MS **MS *MS9 *MS0 *MN MOUNTING STYL - Head nd Flange - Cap nd Flange - Head Trunnion - Clevis Mount, Cap end (furnished with pin) - Rod Mount, Tapped holes front face of head - Foot Mount through holes - ottom Mount - holes total Tapped in head and cap - ottom Mount - holes total Tapped in head and cap - Side Tab Mount with C'bore and through holes - Threaded Nose on head (shipped with mounting nut) *NPG and NHG only ** NG & NHG only STNDRD STROK LNGTHS STOCK STROK LNGTHS /" to 6" in /" increments Longer Strokes vailable, Consult PHD. D DR DC R C CUSHION OR SHOCK PD (Cushion available on Series NG & NHG only) - Cushions on both ends - Cushion on rod end - Cushion on cap end - Shock Pads on both ends - Shock Pad on rod end - Shock Pad on cap end (Cushions, Shock Pads, and Spring Return are not available on the same end of cylinder. Shock Pads are not available for Hydraulic use.) SC NPG MF -/8 x - P - - N-V-Z PROXIMITY SWITCH MOUNTING RCKTS SRIS NPG, NHG NG, NHG -/8" -/8" -/8" -/8" SIZ NO. - -6-6 -7 See Switches and Sensors section for complete ordering information. NPG NHG NG NHG CYLINDR SRIS - 50 psi ir - 500 psi Hydraulic - 50 psi ir - 000 psi Hydraulic NOT: S Ports available. Consult PHD for sizes. SIZ -/8" 5/8" Rod Dia. 7/6-0 Threads -/8" /" Rod Dia. 9/6-8 Threads PORT CONTROL UILT-IN MTR OUT FLOW CONTROL VLV P - Flow control both ends PR - Flow control on head end PC - Flow control on cap end H M N S V W Z OPTIONS - Magnetic Piston for PHD Hall ffect Switches (not applicable on Series NHG & NHG) - Plain keyed rod end - Magnetic Piston for PHD Reed Switches (not applicable on Series NHG & NHG) - Plain Rod nd - Keyed and Threaded Rod nd - Fluoro-lastomer Seals - Close Tolerance Stroke, ±.005 Stroke Length - lectroless Nickel Plate all ferrous parts C- (800) 6-85 www.phdinc.com/n CT-0
C NON-ROTTING ROD CYLINDRS -/8", -/8" SRIS SPCIFICTIONS NPG NHG NG NHG ROD SLS lock Vee with ack-up Ring () lock Vee w/ack-up Ring PISTON SLS () lock Vee () lock Vee with ack-up Ring TU SLS Square Cut O-ring O-ring with ack-up Ring ROD WIPR None Urethane PISTON ROD Hard Chrome Plated Tubing ROD USHING ronze Cartridge Cast Iron Cartridge SPLIN Roll Formed and Hardened CYLINDR RRL Hardcoated luminum Honed Steel ND CPS Zinc Plated Steel lloy TIRODS High Tensile Steel PORTS NPT LURICTION Permanent for Non-Lube ir Permanent for Non-Lube ir WORKING PRSSUR 50 psi ir Max. 500 psi Hyd. Max. 50 psi ir Max. 000 psi Hyd. Max. STNDRD STROKS /" to 6" in /" Increments Longer Strokes vailable, Consult PHD OPTIONS Port Controls, Cushions, Shock Pads, Magnetic Pistons, Fluoro-lastomer Seals FORC TL FORC (lb)/psi DIRCTION -/8" -/8" PUSH.995.85 PULL.687.0 CT-0 (800) 6-85 www.phdinc.com/n C-
DIMNSIONS: SRIS NP MDIUM DUTY; -/8", -/8" SIC CYLINDR DIMNSIONS SQ W.65 + STROK.75.5.5 + STROK X /8 NPT C RM DI FT THRD D WRNCH FLT MM ROD DI.75.5 + STROK MS9 X NT THRD MR X RT THRD TN D SQ.75 + STROK RM +.000 -.005 DI MF.000 + STROK MF X F DI THRU.5 + STROK.50 R R TF UF X F DI THRU.75 TF UF RM +.000 -.005 DI.000.75 MT TY DI WSHR ON -/8 ONLY +.000 -.00 DI OTH SIDS MS0 X C'D HOLS FOR D SHCS TC UT.56.65 TS US.75.50.65 + STROK.50 MN KM THRD.65 + STROK MP (CLVIS PIN INCLUDD) CD DI THRU MR RD CC DI.000.75 XC + STROK L M C CL SIZ D -/8.5 -/8.000.75 ll standard rod ends have four wrench flats (two wrench flats with I option). C.75 LTTR DIMNSION CC CD CL D D F FT KM L M MM MR NT.875.75.875 #0.9 7/6-0 -/.75.65.0 0- x.5 DP.50.5.65 /.8 9/6-8 -/.65.70 /-8 x.8 DP LTTR DIMNSION SIZ R RM RM RT TC TF TN TS TY UF US UT W XC -/8.000.50.000 0- x.5 DP.000.000.875.000.50.65.50.75 -/8.50.5 /-8 x.8 DP N/.50.50.88 N/.65.875..50 PORT POSITIONS: INDICTD Y CIRCLD NUMRS SHOCK PDS: DD /" TO LL (+ STROK) DIMNSIONS FOR CH SHOCK PD SPRING RTURN: DD DDITIONL STROK LNGTH TO LL (+ STROK) DIMNSIONS ( x STROK) C- (800) 6-85 www.phdinc.com/n ll dimensions are reference only unless specifically toleranced. CT-0
DIMNSIONS: SRIS N HVY DUTY; -/8", -/8" SIC CYLINDR DIMNSIONS SQ W.75.50 Y ZJ + STROK P + STROK X NPT FT THRD RM DI D WRNCH FLT MM ROD DI G.5 L + STROK K C MS X NT THRD MR X RT THRD TN D SQ XT SN + STROK RM +.000 -.005 DI MF X F DI THRU ZF + STROK MF X F DI THRU ZJ + STROK.50 R R TF UF TF UF RM +.000 -.005 DI.5 MS X F DI THRU MP (CLVIS PIN INCLUDD) CD DI THRU MR RD CC DI TS US ST SY SY SU SU XS.98 + STROK XC + STROK L M C CL MT TD +.000 -.00 DI OTH SIDS UT TL XG LTTR DIMNSION SIZ D C CC CD CL D F FT G K L L M MM MR -/8.50.50.5 /.8 7/6-0.88.50.65.75.65.70 -/8.000.65.65.65.65.50 /8. 9/6-8.65..8.65.90 SIZ -/8 -/8 RT /-8 x.50 DP 5/6- x.6 DP ll standard rod ends have four wrench flats (two wrench flats with I option). LTTR DIMNSION SN ST SU SY TD TF TL TN TS UF US UT W..75.8..8.8.06.875.000.875.65.875.000.000.50.000.000.50. PORT POSITIONS: INDICTD Y CIRCLD NUMRS CUSHIONS: DD.000 TO LL (+ STROK) DIMNSIONS FOR CH CUSHION SHOCK PDS: CYLINDR LNGTH IS NOT FFCTD Y DDITION OF SHOCK PDS NT /-8 x. DP 5/6- x.50 DP P..8 R.50.65 RM.000.50 XC XG XS XT Y ZF ZJ 5.65.88.875.88.56 5 5.50 6.88.56..56.98 5.98 5 ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/n C-5
C NGINRING DT: CYLINDRS LURICTION- HYDRULIC FLUIDS ll air units are permanently lubricated at the factory and can be used for non-lubricated air service. Static and dynamic seals are compatible with standard petroleum-based oil used for lubrication of air cylinders or as a power source for hydraulic cylinders. For service with other lubricants or hydraulic media, please specify to insure proper seals are supplied. TMPRTUR LIMITS - SLS ll series have una-n and Polyurethane seals and rod wipers for general use between -0 and +80 F. Consult PHD for higher temperatures. HOW TO DTRMIN ND PISTON SIZ. Determine stroke and force required.. Calculate the force (lb) produced by using the effective area figures in Table and multiplying them times the operating pressure (psi).. Check Table to verify that rod size is sufficient for force. If stroke required is greater than length listed in Table, increase rod diameter or go to larger bore size. NOT: Table shows maximum stroke lengths for mounting styles -F, -, -R, -T, -RF, and -CF, MS, MS, MR, MF, MF, MN fastened to rigid base. For mounting styles -K, -P, and MP; divide table value by. For mounting styles -TR, MT, and MT; divide table value by.75. To avoid excessive wear on rod bushings and seals, it is recommended that cylinders with strokes exceeding the following lengths be equipped with " long stop tubes or be stopped externally " short of full push stroke. /" ore x 8" -/8" ore x " " ore x 0" -/8" ore x 8" For -P, -K, MP, MT, MT and -TR mountings use / of above values. RKWY The breakaway pressure for all pneumatic cylinders in section C is 0 psi at zero load. The breakaway pressure for all hydraulic cylinders in section C is 0 psi at zero load. Field Maintenance Videos on filling and bleeding ir/oil Tandem ctuators are now available. Contact your local PHD distributor or call our toll free number: -800-6-85. MXIMUM WORKING PRSSURS HYDRULIC IR MX. MX. WITH - OR -M SRIS psi psi OPTION V 50 HV 500 500 50 50 L 500 500 H 000 500 S 5000 500 NPG 50 NHG 500 500 NG 50 NHG 000 500 MXIMUM IR/OIL TNDM CYLINDR VLOCITY in/sec PRSSUR psi /" " -/8" -/8" 0 xtend 0.68.6.66.07 Retract.00.6.0.60 60 xtend.6.07.. Retract.50.00..5 80 xtend.7..8.80 Retract.00..87. 00 xtend.06.8 5.00 5. Retract...6.80 Minimum recommended velocity for all bore sizes at pressures from 0 to 50 psi is. in/sec. STROK TOLRNC Tolerance on the nominal stroke length is ±.0 for all cylinders in section C. TL NPG, NHG, NG, NHG MXIMUM LLOWL PUSH STROK ROD CYLINDR FORC (lb) SRIS DIMTR 00 00 500 000 500 000 000 5000 / " 9" 6" " " " /",", -/8" 5/6 8" " 8" 6" 5" " V, HV, /8 6" 8" " 9" 7" 6" / 6" " " 5" " 0" 5/8 7" 5" " " 9" 6" /8 7" 9" " 8" 7" 6" 5" " -/8" V, HV / 8" " " 5" " " 9" 7", L, H, S 5/8 7" 5" " " 9" 7" " " / 07" 76" 8" " 8" " 0" 5" 5/8 " " 8" 0" 6" " " / " " " 9" " 0" 7" C-6 (800) 6-85 www.phdinc.com/products/cylinders CT-0
NGINRING DT: CYLINDRS TL CYLINDR FORC TL FFCTIV FR IR CONSUMPTION DISPLCMNT CYLINDR ROD ROD R FORC 80 lbs GL./in SRIS DIMTR DIRCTION lb/psi CUIC ft/in OF STROK OF STROK / / Push..006.009 Pull.9.00.007 / 5/6 Push..006.009 Pull.65.00.006 5/6 Push.785.009.00 Pull.709.006.00 /8 Push.785.009.00 Pull.676.005.009 V, HV, -/8 /8 Push.99.007.00 Pull.88.00.008 -/8 / Push.99.007.00 Pull.799.009.00 -/8 / Push.85.0055.006 Pull.89.008.0056 -/8 5/8 Push.85.0055.006 Pull.78.00.005 / /8 Push..006.009 Pull..00.005 -/8 / Push.99.007.00 Pull.798.000.00, L, H, S -/8 5/8 Push.99.007.00 Pull.687.006.000 -/8 5/8 Push.85.0055.0065 Pull.78.00.005 -/8 / Push.85.0055.0065 Pull.0.09.005 -/8 5/8 Push.99.007.00 NPG, NHG, Pull.687.006.000 NG, NHG -/8 / Push.85.0055.006 Pull.0.009.005 NOT: Use the Pull figures for calculating double rod cylinder forces in both directions. C CYLINDR UNIT WIGHTS (lb) SRIS ZRO STROK DDR PR INCH OF STROK VR /..0.87.07 -/8.95.0 -/8.56. MR /..96 -/8.70.5 -/8 5.05. NPGMR -/8.55. -/8.6.9 NGMR -/8.68.6 -/8 5.06. CT-0 C-7 (800) 6-85 www.phdinc.com/products/cylinders
NGINRING DT: NON-ROTTING ROD CYLINDRS C SIDLODING Care should be taken to consider allowable side load versus stroke in the same manner as standard cylinders, including stop tubes and transverse support members as needed. Where appreciable sideloads are expected the use of powered slides, shown in Section 5 of this catalog, is recommended. Rod deflection may be calculated according to formula below. D = W x L C D = Deflection at rod end L = Distance in inches from bushing to applied sideload W = Sideload in pounds C VLU -/8 70,000 -/8 990,000 TORSION ND CKLSH Clearance between spline and broached teeth in piston is less than /. dditional deflection caused by rotational moments can be calculated using the following formula: Where: θ = ngular deflection in minutes of arc T L = Torque applied (in/lb) = Distance that rod is extended θ = T L K + L K +C L L SRIS K K C -/8 NP 8.7.8.8 N 8.7.8.5 -/8 NP 5.6 7.8.0 N 5.6 7.8. L K K RTRCTD POSITION = Stroke length = Constant reflecting the polar moment of inertia and the modulus of rigidity for the spline rod = Constant reflecting the polar moment of inertia and the modulus of rigidity for the piston rod C = Constant value of deflection on spline and piston rod regardless of piston position MXIMUM LLOWL TORQU Table shows maximum recommended torsional loads which may be applied to piston rod without spline rotating relative to cylinder cap. Safety factor equals approximately :. Cylinder will encounter fractional losses due to torsional loads. MX. TIGHTNING TORQU TORQU ON JM SCRWS in-lb in-lb -/8 8 85 -/8 7 85 JM SCRWS C-8 (800) 6-85 www.phdinc.com/products/cylinders CT-0
OPTIONS: CYLINDRS P PORT CONTROL The exclusive PHD Port Control, based on the "meter-out" principle, features an adjustable needle and a separate ball check. oth are built into the cylinder end cap and are used to control the speed of the cylinder over its entire stroke. The self-locking needle has micrometer threads and is adjustable under pressure. It determines the orifice size which controls the exhaust volume. The separate ball check is closed while fluid is exhausting from the cylinder, but opens to permit full flow of incoming fluids. The PHD Port Control provides the optimum in speed control for small bore cylinders. It saves space and eliminates the cost of installation and fittings for external flow control valves. C STNDRD PORT CONTROL CUSHION NDL POSITIONS (/", ", -/8" ore Series, V, HV, and all NP and N Cylinders) Port Control and cushion needles are located in position on standard cylinders. They may be located at position when specified on all Series, V, and HV. Consult PHD for special Port Control needle positions on Series NP and N cylinders. PORT CONTROL NDLS CUSHION CONTROL NDLS STNDRD PORT CONTROL & CUSHION NDL POSITIONS (-/8" ore Series V, HV and all Cylinders) Port Control and cushion needles are located on opposite sides adjacent to port. Please consult distributor or PHD to check availability of special Port Control or cushion needle positions. PORT CONTROL CUSHION PORT CONTROL & CUSHION D DJUSTL CUSHION PHD Cushions are designed for smooth deceleration at the end of stroke. When the cushion is activated the remaining volume in the cylinder must exhaust past an adjustable needle which controls the amount of deceleration. See Dimension pages for dimensional information. /", ", -/8" Series, V, HV & all N = Cushion lock -/8" Series V, HV & all = Poppet Style PORT CONTROL ND DJUSTL CUSHION COMINTION (/", ", -/8" ore Series, V, HV and all N Cylinders) Cushion and Port Control combination arranged in series provides a compact efficient control system for maximum space weight and cost savings. The cushion is activated when the piston extension enters a seal in the cushion block. The remaining volume in the cylinder exhausts past an adjustable needle. check seal in the adjusting needle is closed during deceleration, but opens to permit full flow for immediate reversing. The cushion seal in the block is an O-ring for air units. CUSHION LOCK STYL O-RING SL SL RTINR CUSHION LOCK POPPT STYL /", ", -/8" -/8" PORT CONTROL ND DJUSTL CUSHION COMINTION (-/8" ore Series V, HV and all Cylinders) The cushion and Port Control combination is also available on the -/8" ore. This cushion is activated when a seal, which is traveling with the piston, seals against the cylinder end cap. This causes the remaining volume in the cylinder to exhaust past an adjustable needle which controls the amount of deceleration. The spring, which extends the seal from the piston, permits the seal to act as a check valve to allow full flow back into the cylinder for immediate reversing. The cushion seal for air units is made of urethane while seals for oil units are close tolerance metal. POPPT STYL PORT CONTROL CUSHION CUSHION PORT CONTROL CT-0 C-9 (800) 6-85 www.phdinc.com/products/cylinders
OPTIONS: CYLINDRS H7 RODLOK CYLINDR & RODLOK vailable on single rod Series and V units only. (preassembled) C PHD s Rodlok is ideal for locking the piston rod while in a static / stationary position. When the pressure is removed from the port of the Rodlok, the mechanism will grip the rod and prevent it from moving. The loads are held indefinitely without power. The Rodlok may also be used in intermittent dynamic use as a pressure off piston rod deceleration device. Rodlok performance (ccuracy and Stopping distance) is application and environment sensitive (Cleanliness of rod or Rodlok will also affect performance). TH RODLOK IS NOT DSIGND TO USD S PRSONNL SFTY DVIC. (-H7) Cylinder with rod locking device and adaptor preassembled RPLCMNT RODLOK KITS Option H7 provides a cylinder and Rodlok pre-assembled. The port for the Rodlok will be assembled in the same position as the port on the extend end of the cylinder. Replacement Rodlok kits can be purchased separately. See chart at right. The locking device and adaptor are not available with the -Z corrosion resistant finish. in / -/8 -/8 STTIOCKING FORC* lb [N] 0 56 79 5 H SQ 80 50 50 600 DYNMIC LOCKING FORC ctual dynamic locking forces are application sensitive. nvironmental conditions, load weights, attitude, pressure, and speed influence performance. NOT: *LOCKING FORC GIVN IS TH CTUL LOCKING FORC WITH DRY CLN ROD ND DOS NOT INCLUD NY SFTY FCTOR. in / -/8 -/8 LOCKING DVIC KIT 69-0 69-0 69-0 69-0 DPTOR KIT 69-0 69-0 69-0 69-0 COMPLT RODLOK 695-0 695-0 695-0 695-0 PRT NUMRS LISTD OV R INTNDD FOR RPLCMNT PURPOSS ONLY. U R S N PORT O X L THRD DP.5 (DP.75 ON -/8 ) Ø K + STROK (S NOT ) J D SQ Ø F ±.00 TN SQ This option does not dimensionally comply with the NFP standard specifications. X M THRD x DP T (/,, -/8 ) X M THRD x DP T (-/8 ) Q C + STROK (S NOT ) in / -/8 -/8.50 [6.]. [7.9].75 [9.5] [.7] C.06 [77.8].000 [76.].000 [76.] 5.00 [7.0].000 [5.].75 [.9] [8.].875 [7.6] F.6 [5.8].77 [9.0].77 [9.0].6 [.6] H 0.78 [8.5] 0.787 [0.0] 0.787 [0.0] 0.855 [.5] J [.7].688 [7.5] [9.].98 [.8] K.50 [57.].50 [57.].50 [57.].8 [96.8] NOTS: ) reakaway force on cylinders with Rodlok approximately 0 psi. LTTR DIMNSION L 8- UNC- 8- UNC- 0- UNF- /-8 UNF- M 8- UNC- 8- UNC- 0- UNF- /-8 UNF- N 0- UNF- 0- UNF- 0- UNF- 0- UNF- O.09 [6.].756 [70.0].89 [7.6].99 [8.8] Q [8.] [8.] [8.] [.5] R.65 [.].65 [.].65 [.].8 [55.5] S.65 [5.9].65 [5.9].65 [5.9].000 [5.] ) For Series /,, and -/8 bores, subtract (K =, C : / =.56,, -/8 = ) T.87 [.7].50 [6.].50 [6.]. [7.9] U.875 [7.6].875 [7.6].875 [7.6]. [6.8] D [9.].000 [5.].5 [8.6].75 [.9] TN.65 [5.9].875 [.].000 [5.] [9.] C-0 (800) 6-85 www.phdinc.com/products/cylinders ll dimensions are reference only unless specifically toleranced. CT-0
OPTIONS: CYLINDRS SHOCK PDS Polyurethane pads for absorption of shock and noise (not available on hydraulic units). Reducing shock permits higher piston velocities for shorter cycle times. Reducing noise levels provides improved environment for increased productivity. liminates metal to metal contact between piston and end caps. Shock pad available together with all options XCPT - Same end as Cushion Spring end of Spring Return cylinder Same end as Stroke djustment C SR SC Stroke adjustment screws are available to decrease the retraction stroke of any Series V,, or cylinders. The standard adjusting range is / inch. Longer adjusting lengths are available on request. Series V and not available with: P, K, and CF mounting styles. lso, F mounting styles on a Z MX H /" bore with -P or -PC and /6 HX - options. ll other mounting styles, consult PHD. Z THRD H SIZ /.70.6 -/8.6 -/8.6 Z Z STNDRD.0 /8-.56 /-0.56 /-0.000 /-0 Z WITH -P OR -PC 5/6- /8- /-0 /-0 PORT POSITIONS Port position is standard on all cylinders except mounting style -F (MS8) without port controls. The cap end port will be in Q SPRING RTURN vailable in /" increments ll standard, V and HV Cylinders from /" to 6" of stroke, and NP Cylinders from /" to " of stroke can be built with internal springs to return or extend the piston rod in single acting applications. The standard spring provides a preload and a spring rate per chart below. Other spring combinations will be quoted on request. (Not available on Series and N Cylinders) STROK PRLOD RT /"-" lb 7 lb/in -/" - 6" lb -/ lb/in CYLINDR STROK DJUSTMNT PORT POSITION vailable with all options XCPT - Cushion on the spring end Shock pad on the spring end Stroke adjustment on the spring end vailable with all options XCPT - Cushion on the cap end Shock pad on the cap end Spring on the cap end Pivot Mount, Pivot on cap Series availability: MS, MS, MF, MT, MT, and MR mounting styles. K Z MX Z ZC SIZ K / 0.00 -/8.50 -/8. ZD DI LTTR DIMNSION Z Z ZC.9.5 /8 HX.5.875 / HX.5.8 / HX ZD.000.50 position standard. If port position (-Q) or (-T) is desired; add -Q or -T to unit description and -F mounting tab will be added to unit to accommodate /,, -/8, V, HV, and units. T PORT POSITION R PORT POSITION U PORT POSITION CT-0 C- (800) 6-85 www.phdinc.com/products/cylinders
OPTIONS: CYLINDRS MGNTIC PISTON FOR US WITH PHD PROXIMITY SWITCHS HLL FFCT SWITCHS M RD SWITCHS C PHD Cylinders may be equipped with a magnetic band (specify -) on the piston which activates externally mounted PHD Hall ffect Switches. These switches allow the interfacing of the Tom Thumb air or hydraulic cylinder to various logic systems. This option is for use with the following switches. COMPCT HLL FFCT SWITCHS PRT NO. DSCRIPTION 750--06 NPN Type.5- VDC 750--06 PNP Type.5- VDC 75- NPN Type.5- VDC, Quick Connect 75- PNP Type.5- VDC, Quick Connect LIQUID RSISTNT HLL FFCT SWITCH PRT NO. DSCRIPTION See each ordering data for magnetic piston ordering information. See Switches and Sensors section for complete switch information. The PHD Magnetic Reed Switches may be used in situations where the Hall ffect Switches are not applicable. s with the Hall ffect Switches, a magnetic band (specify-m) on the piston activates the externally mounted PHD Reed Switches. The Reed Switches may be used to signal a programmable controller, sequencer, relay, or in some cases, a valve solenoid. This option is for use with the following switches. COMPCT RD SWITCHS PRT NO. DSCRIPTION 750--06 Sink or Source Type.5- VDC 7509--06 C Type 0-0 VC with Current Limit 75- Sink or Source Type VDC, Quick Connect 759- C Type 0-0 VC, Quick Connect with Current Limit 590- Sink and/or Source Type.5- VDIQUID RSISTNT RD SWITCHS PRT NO. DSCRIPTION 5900-0 Watt Reed Switch 590- Triac V FLUORO-LSTOMR SLS _K XTR ROD XTNSION Fluoro-lastomer seals are available to achieve seal compatibility with certain fluids. Seal compatibility should be checked with the fluid manufacturer for proper application. Consult PHD for high temperature use. Z LCTROLSS NICKL PLTING lectroless nickel plating is done on all externally exposed ferrous parts except rods and rod end, or parts made of stainless steel or aluminum. This optional plating treatment gives an alternative method of protecting the cylinder from severe environments. NOT: Standard plating is rite Zinc. This option may be specified when extra plain rod extension between rod flats and cylinder snout is desired. Length is specified in /8" [ mm] increments. Length code example (for imperial units) -K = / of extra rod extension -8K =, etc. Length code example (for metric units) -K = mm of extra rod extension -K = mm, etc. -K= I =, M = mm W CLOS TOLRNC STROK This option may be specified when a precise stroke length is required and stroke adjustment is not acceptable. y specifying this option, a stroke length with a tolerance of ±.005 will be supplied. Standard stroke tolerance is ±.0. Maximum stroke for cylinders with close tolerance is 8". NOT: This option is not available with shock pads (-). NOT: On double rod end cylinders and -_K specified will be applied to one end of cylinder only (head end/primary mounting end). C- (800) 6-85 www.phdinc.com/products/cylinders CT-0
OPTIONS: CYLINDRS Y S PORTS FOR SRIS HV /", ", -/8" ore S Ports are available on most Tom Thumb Hydraulic Cylinders. The /", ", and -/8" ore Series HV Cylinders require a boss which is brazed to the head and cap. Dimensions for this boss are shown below. This option is not available on cylinders with an F mounting style. Consult PHD for optional port position or units with Port Controls. Oversize rods are available except on T & L mounting styles on /" bore cylinders. C S Ports are available on other PHD Cylinders and ctuators. Consult PHD for port size and dimensions. X 7/6-0 S PORT THRD.65 DI.650. SLF-LIGNING PISTON ROD COUPLRS To order, specify the model number. MODL NO. 50 75 7 500 65 750 /-8 5/6- /8-7/6-0 /-0 5/8-8 /-6 LTTR DIMNSION C D.000.65.875.000.65.875.000.65.875.5.87.5.87.5..8.5..8 F.875.875.875.000.000.56.56 G.56.87.9.50..75. INTRNL THRD x DP F DI G Rod Couplers eliminate expensive precision machining for mounting fixed or rigid cylinder on guide or slide applications. Cylinder efficiency is increased by eliminating friction caused by misalignment. Couplers compensate for angular error and /" lateral misalignment on push and pull stroke. (Miniature Couplers compensate for of angular error.) Couplers provide greater reliability and reduce cylinder and component wear, simplifying alignment problems in the field. Rod Couplers are manufactured from high tensile and hardened steel components. For metric piston rod couplers, see page D-. THRD.0 LTRL COMPNSTION NGULR COMPNSTION D C MINITUR COUPLRS D H F G ST DI J WRNCH FLT C DI K MIN DISTNC FOR TWO PIC SSMLY.05 LTRL COMPNSTION THRD THRD x DP S N DIM. FOR TH MX SSMLY TORQU MODL LTTR DIMNSION NO. C D F G H J K N 900-0 5-0.60.0.75.50.70.066 5/6.90 0 in-lbs 900-0 0/.50.560.8.558.00.058 /8.90 70 in-lbs ll dimensions are reference only unless specifically toleranced. CT-0 C- (800) 6-85 www.phdinc.com/products/cylinders
OPTIONS: SRIS, V, HV ROD NDS & OVRSIZ RODS C /", ", -/8" CYLINDRS F ROD ND STYL # STNDRD ON: (/", ", -/8" ) G ROD ND STYL #.50 RM DI D WRNCH FLT FT THRD W RM DI D WRNCH FLT FT THRD L CORS THRD ROD ND I ROD ND STYL #.50 RM DI D WRNCH FLT CT THRD W RM DI D WRNCH FLT T THRD.50 W.50 J ROD ND STYL #X RM DI D WRNCH FLT FT THRD N PLIN ROD ND RM DI D WRNCH FLT.50 C W.50 SIZ / -/8 ll standard rod ends have four wrench flats (two wrench flats with I option). ROD TYP STNDRD OVRSIZ STNDRD OVRSIZ STNDRD OVRSIZ ROD DI..50...75.75.65.65.65.65.65 C.50.50.50.50.50 CT /-0 5/6-8 5/6-8 /8-6 /8-6 /- LTTR DIMNSION D FT FT 7/ /-8 0- / 5/6- /-8 / 5/6- /-8 5/6 /8-5/6-5/6 /8-5/6-7/6 /-0 7/6-0 RM.65.65 - V-HV.000 T 6- x.7 DP 0- x.65 DP 0- x.65 DP /-8 x.65 DP /-8 x.65 DP /8- x.65 DP W.56.87.87.9.9. W.0.56.56.87.87.50 NOT: On double rod cylinders, both rod ends will be the same on both ends of the cylinder. -/8" CYLINDRS G ROD ND STYL # STNDRD ON: (-/8" ).50 D WRNCH FLT FT THRD W L CORS THRD ROD ND.50 D WRNCH FLT CT THRD W F ROD ND STYL # D WRNCH FLT FT THRD I ROD ND STYL # D WRNCH FLT T THRD.50 W.50 J ROD ND STYL #X D WRNCH FLT FT THRD N PLIN ROD ND D WRNCH FLT W.50.50 ll standard rod ends have four wrench flats (two wrench flats with I option). C- (800) 6-85 www.phdinc.com/products/cylinders SIZ ROD TYP -/8 STNDRD OVRSIZ ROD DI..65 CT /8-6 7/6- LTTR DIMNSION D FT FT T W W 7/6 /8-7/6-0 /8- x.65 DP.9.50 9/6 7/6-0 /-0 7/6-0 x.65 DP.50. ll dimensions are reference only unless specifically toleranced. CT-0 NOT: On double rod cylinders, both rod ends will be the same on both ends of the cylinder.
OPTIONS: SRIS, V, HV MOUNTING TTCHMNTS Y RCKT FX.97 CD DI THRU DI. X C'D HOL FOR DD SHCS* C SQ SQ SIZ CYL PRT NO. 077-0 SRIS / & -/8,V,HV V,HV 077-0.000 077-0.000 *For / bore thru hole only. LTTR DIMNSION C CD DD*.8.50 #6.000.7.50 #0.75.7.75 #0.75 FX.577.7.7 ROD Y CD DI THRU CD.8 C FT THRD C CC DI SIZ / -/8 CYL SRIS,V,HV V,HV V,HV PRT NO. 075-0 075-0 075-0 075-0 075-05 C.875.875.875.875 C.8.7.7.7.7 LTTR DIMNSION CC CD CD.50.50.50.75.75.75.50.75.75.75 FT /-8 x.75 DP 5/6- x.75 DP 5/6- x.75 DP /8- x. DP /8- x. DP C CLVIS RCKT - PIN INCLUDD F CD DI THRU CC DI L FL CD ROD CLVIS - PIN INCLUDD CD CD DI. THRU C.5 FT THRD C X C'D HOL FOR DD SHCS* C CC DI CC DI SQ SQ CYL KIT LTTR DIMNSION SIZ SRIS NO. C CC CD CD DD* / & -/8,V,HV V,HV 90 90 90.5.50.000.79.875.50.000.79.875.75.50.75.75 #6 #0 #0 *For / bore thru hole only. CYL SIZ SRIS /,V,HV V,HV -/8 V,HV KIT NO. 90 905 906 907 908 C.8.875.875.875.875 C.5.79.79.79.79 CC.875.875.875.875.000.75.75 F.60 LTTR DIMNSION CC CD CD.7.50.50.56.50.75.56.75.75.56.50.75.56.75.75 FL.87.50.50 L.5.5 FT /-8 TO SLOT 5/6- TO SLOT 5/6- TO SLOT /8- TO SLOT /8- TO SLOT Y RCKT DI THRU.000 DI X.8 DI THRU.75 SQ.875 SQ SIZ CYL SRIS -/8 V & HV PRT NO. 0.875.50 ROD Y DI THRU.875.8.65.570 SIZ CYL SRIS PRT NO. 75-0 LTTR DIMNSION FT /8- x DP -/8 V & HV 75-0 75-0 7/6-0 x DP /-0 x DP FT THRD.65 ROD CLVIS - PIN INCLUDD DI THRU.875.7.65.75 SIZ CYL SRIS -/8 V & HV KIT NO. 909 90 9 LTTR DIMNSION FT /8- TO SLOT 7/6-0 TO SLOT /-0 TO SLOT FT THRD.5 ll dimensions are reference only unless specifically toleranced. CT-0 C-5 (800) 6-85 www.phdinc.com/products/cylinders
OPTIONS: SRIS ROD NDS & OVRSIZ RODS F ROD ND STYL #.50 RM DI D WRNCH FLT FT THRD W I ROD ND STYL # RM DI D WRNCH FLT T THRD.50 C J ROD ND STYL #X.50 C RM DI D WRNCH FLT FT THRD W L CORS THRD ROD ND.50 RM DI D WRNCH FLT CT THRD W SIZ / -/8 -/8 ROD TYP STNDRD STNDRD OVRSIZ STNDRD OVRSIZ ROD DI..75.65.65.000 C.000 CT /-0 /8-6 7/6-7/6-9/6- D..8.56.56.688 LTTR DIMNSION FT RM 5/6-7/6-0.000 /-0.000 /-0.50 5/8-8.50 FT /-8 /8-7/6-0 7/6-0 9/6-8 T /-8 x.65 DP /8- x.65 DP 7/6-0 x.65 DP 7/6-0 x.65 DP 9/6-8 x.65 DP ll standard rod ends have four wrench flats (except -I rod end style). W.56.9.50.50. W.87.50...75 NOT: On double rod cylinders, both rod ends will be the same on both ends of the cylinder. SRIS MOUNTING TTCHMNTS Y RCKT X DD DI THRU CD DI THRU MR SQ SQ SIZ / -/8 -/8 PRT NO. -0 0-0.000.75.65 LTTR DIMNSION C CD DD F FL.75.75.9.75.8.5.8.875.875.50.65.65..50.06.56 MR.000.50 F FL CD C ROD Y R RD CD DI THRU CD L CD C FT THRD C CC SIZ / -/8 -/8 PRT NO. -0 75-0 -0-0 C.56.000.000 C.75.65.65 CC.65 CD.75.65.65 LTTR DIMNSION CD CD R.75.5.8.875.65.65.50.906.65.50.906 FT L /-8 X.75 DP.56 /8- X.75 DP.65 7/6-0 X.00 DP.8 9/6-8 X.00 DP.8 ROD CLVIS - PIN INCLUDD R RD CD DI THRU CD L CD C C SIZ / -/8 -/8 KIT NO. 9 909 9 95 C CC CD.75.875.75.5.65.75.65.65.75.65 LTTR DIMNSION CD C..875.75.50.8.50.8 CD.75.8.65.65 R.5.65.906.906 FT L /-8.56 /8-.65 7/6-0.8 9/6-8.8 FT THRD CC TRUNNION RCKT F LT TD TD DI THRU TC T TU U X DD DI THRU R W PRT LTTR DIMNSION SIZ NO. DD F LT R T TC TD TU U W / -/8 -/8 5-0.8.50.000.75.75.5.65 5-0.8.000.50.50.000 5-0..65.5.75.50.000.875.875 5.000 C-6 (800) 6-85 www.phdinc.com/products/cylinders ll dimensions are reference only unless specifically toleranced. CT-0
OPTIONS: SRIS N ROD NDS & MOUNTING TTCHMNTS S ROD ND L KYWY FOR J KY N RD R FOR HRDND ST INSRT IS INCLUDD +.000 M -.00 DI D WRNCH FLT G THRD C F KYWY ORINTTION: FULLY DJUSTL KY & JM NUTS: INCLUDD K H THRD SIZ -/8 -/8.87.75.000.000 C.56.65 D / 5/8.5. F.85.977 LTTR DIMNSION G H J K L 5/8-8 /-0 /8 x /8 x 5/8.5.65 /-6 5/8-8 /6 x /6 x /.56.65 M.65 N.09.5 C H ROD ND N ROD ND H C RD.5 MM DI D KYWY F DI D WRNCH FLT THRD G SIZ -/8 -/8.65.75.8 C.56.9 D /8 x /6 x.00 /6 x / x.0 KYWY ORINTTION: FULLY DJUSTL KY: INCLUDD FOR D KYWY SIZ -/8 -/8 ROD DI.65 LTTR DIMNSION C D.970.50 /.095.50 5/8 LTTR DIMNSION 0- x. DP 5/6- x. DP F G.09.56 H.75 N/ MM.65 N/ Y RCKT ROD Y.906 RD.65 DI THRU F FL CD.50 C CD DI THRU.65.8.000 FT THRD SQ. ll standard rod ends have four wrench flats. C.65 MR SQ X DD DI THRU SIZ -/8 -/8 CYL SRIS NPG, NHG NG, NHG NPG, NHG NG, NHG PRT NO. -0 0 0-0.000.75.75.65 PRT LTTR DIMNSION SIZ NO. FT -/8-0 -/8-0 7/6-0 X.00 DP 9/6-8 X.00 DP C.75.65 LTTR DIMNSION DD F FL.9.75.8.5.8.875.875.50.8.875.875.50..50.06.56 CD.75.65 MR.000.000.50 ROD CLVIS - PIN INCLUDD.906 RD.65 DI THRU.50.65.8.8.65 SIZ -/8 -/8 KIT NO. 9 95 LTTR DIMNSION FT 7/6-0 9/6-8 FT THRD.75 TRUNNION RCKT TD DI THRU W U TC R SIZ -/8 -/8 CYL SRIS NG, NHG NG, NHG PRT NO. 5-0 5-0 LTTR DIMNSION DD F LT R T TC.8.000.50.50..65.5.75.50.000 TD.875 TU U.000.875 5 W.000 F LT TD T TU X DD DI THRU ll dimensions are reference only unless specifically toleranced. CT-0 C-7 (800) 6-85 www.phdinc.com/products/cylinders
C CLNROOM CYLINDR VCUUM PORT NFITS Cleanroom option allows PHD Tom Thumb Cylinders to be used in Class 00 cleanroom applications. Vacuum port and special bushing minimize particles from rod gland area. vailable on Series V and, /", ", and -/8" bore cylinders. Compatible with all mounting styles and standard diameter rod options. No change to existing catalog dimensions addition of vacuum port only. ORDRING DT TO ORDR SPCIFY: Series, Mounting Style, ore Size, Stroke, and Options. SRIS V - 50 psi ir - 50 psi ir SIZ /" /" Rod Dia. /-8 Thread " 5/6" Rod Dia. 5/6- Thread -/8" /8" Rod Dia. /8- Thread Some cleanroom applications may require -Z electroless nickel plating of all ferrous parts. Consult PHD for any special lubrication requirements. OPTIONS O - Cleanroom Vacuum Port Z - lectroless Nickel Plate all ferrous parts excluding Rod nds. x - V F O-Z MOUNTING STYL F - Foot Mount, C'bored F through holes - ottom Mount, Tapped holes in head and cap R - Rod Mount, Tapped R holes on front face of head T - Thread Mount, Threaded T snout on head (shipped with mounting nut) RF - Rod nd FlangeRF CF - Cap nd FlangeCF L - Pilot Mount, Threaded L snout and pilot diameter on head (shipped with mounting nut) P - Pivot Mount, Pivot P on cap STNDRD STROK LNGTHS /", ", -/8" SIZS /" to 5" in /" increments DIMNSIONS.65 + STROK.50.5 + STROK X /8 NPT SIZ LTTR DIMNSION /", ", -/8" C SRIS V.65.50 SRIS.5.000 SPCIFICTIONS 0- X.56 DP VCUUM PORT PRSSUR RTING Cylinder - 50 psi maximum, air only Vacuum Port - up to 5 In. Hg..0 C + STROK MTRIL ND PLTING asic Tom Thumb Cylinders have zinc plated steel end caps, black oxide steel tierods, hardcoated aluminum tubes, and stainless steel rods. option -Z provides electroless nickel plating of external ferrous parts if required. Consult PHD for other plating or materials. VCUUM CONNCTIONS Manufacturer fittings differ. Due to close proximity of vacuum port to cylinder head port, the 0- vacuum port may require the use of a 0- barb fitting depending on fitting manufacturer used. See Cylinder, V, HV section of catalog for complete cylinder dimensions and mounting styles. CLNROOM RTING SRIS CYLINDR ROD ROD FFCTIV R DIMTR DIRCTION FORC (lb)/psi / / PUSH. PULL.9 V, 5/6 PUSH.785 PULL.709 -/8 /8 PUSH.99 PULL.88 PHD Tom Thumb Cylinders with vacuum ports have been tested and comply with Class 00 cleanroom requirements for particle count and size. C-8 (800) 6-85 www.phdinc.com/products/cylinders ll dimensions are reference only unless specifically toleranced. CT-0
ISO STNDRD 6, 6, ND VDM 56 SRIS CV CYLINDRS INDX: Product Selection Guide Pages D- and D- Ordering Data Page D- D Series CV are full feature cylinders providing exceptional performance. 0 & 5 mm Sizes enefits Page D-5 Dimensions Pages D-6 and D-7 ngineering Data Pages D-8 to D- Options Pages D- to D-8 Mounting Styles Pages D-9 and D-0 Mounting ccessories Pages D- to D-9 pplication xamples PagesD-0 N INDUSTRY STNDRD WITH MUCH MOR! DOUL ROD NDS RODLOK HUSHCONTROL POSITION CT-0 (800) 6-85 www.phdinc.com/cv D-
PRODUCT SLCTION GUID: SRIS CV CYLINDRS SRIS CVC CYLINDRS 0 & 5 mm ISO 6 D vailable in bore sizes 0 mm and 5 mm. Conforms to ISO 6 customer interface and overall unit length when specified with optional -P or -Q mounting. SRIS CV CYLINDRS 0 & 5 mm vailable in bore sizes 0 mm and 5 mm. Custom interface conforms to ISO 6 specifications. SRIS CV CYLINDRS -00 mm ISO 6 Standard mm through 00 mm bore units conform to ISO 6 and VDM 56 specifications. SRIS CV position CYLINDRS Series CV and CV are available as position units. D- (800) 6-85 www.phdinc.com/cv CT-0
PRODUCT SLCTION GUID: SRIS CV CYLINDRS Mounting ccessories page D- Why uy D Rodlok page D- PHD? ecause PHD will provide the support, software, and delivery you need! U nique application designs require unique components. With over 0 years of experience, our Custom Products team welcomes special requests for unique products, regardless of quantity or frequency of order. Call -800-6-85 to request a quote. P HD distributors are factory trained, application oriented, and carry a wide range of supporting product lines. Your local distributor will take the time to thoroughly analyze and assess your specific needs. Hushcontrol page D-5 PHD SOLUTIONS Contact your local distributor today for the full story including a working product demonstration at your site. P HD s engineering software provides powerful design and selection tools at your fingertips. The software eliminates risk and simplifies your design process and component selection, while offering significant time savings. ven with the wide range of options offered on PHD products, shipping time in most cases is one to four working days. In today s fast-paced competitive markets, we understand the need for quick turnaround. With a track record of 98% on-time shipments, you can be assured of prompt delivery. nd if you find yourself in an emergency situation, expedited service is also available. CT-0 (800) 6-85 www.phdinc.com/cv D-
ORDRING DT: SRIS CV CYLINDRS D RR PIVOT MOUNTING STYLS TO ORDR, SPCIFY: Product, Series, Type, Design No., Mounting style, ore size, Stroke, and any Options. PRODUCT C - Cylinder TYP S - Single Rod, double acting (Standard) D - Double Rod, double acting (Not available on position units.) P MOUNT Q MOUNT THR POSITION UNIT (Specify only if needed) MOUNTING STYL P - Rear pivot in position 5 Q - Rear pivot in position 6 V - Standard mounting female threads each end per ISO 6/VDM 56 & ISO 6* (-P and -Q available on 0 & 5 mm bores only) MTRIC STROK (CVx5) STNDRD STROK LNGTHS (5 mm = minimum stroke in 5 mm increments) [mm] CVC0 CVC5 CV0 CV5 0 50 6 80 00 MXIMUM STROK [mm] 500 500 750 750 000 000 000 000 000 000 Contact PHD for shorter or longer strokes. CUSHION CONTROL D - Cushion Controls oth nds D - Cushion Control xtend Only DR- Cushion Control Retract Only Standard cushion control locations are & 5. See note 7. See page D- for more information. XTND ND 8 OPTIONL PORT LOCTION U00 - Ports on all sides, both ends (Not available with Port Controls on same end) Contact PHD For other combinations. Standard port locations are & 5. See page D-8 to specify other locations. 5 7 RTRCT ND 6 Location definition for ports, cushion controls, and port controls MODL NUMR C V S 5 P 0 5 x 5 - P D - U00 - M-Z SRIS SIZS 0 & 5 mm ONLY V - ISO 6 50 psi [0 bar] ir VC - ISO 6 50 psi [0 bar] ir SRIS SIZS -00 mm V - VDM 56 ISO 6 50 psi [0 bar] ir! DSIGN NO. 5 - Metric mm 0 5 0 50 6 80 00 Options may affect unit length. See unit dimension and options pages for adders. SIZ PISTON R in.787.98.6.58.97.8.5.9 sq mm 9 80 57 96 7 507 785 sq in.86.760.5.95.05.8 7.79.7 POSITION Full xtend STROK CYLINDR Total Stroke STROK CYLINDR From Retract to Mid Position ( position only) POSITION Mid-Position POSITION Full Retract PORT CONTROL UILT-IN MTR OUT FLOW CONTROL VLV P - Port Controls oth nds P - Port Control xtend Only PR - Port Control Retract Only Standard port control locations are & 5. See note 7. See page D-7 for more information. NOTS: ) -Z option may have reduced cylinder performance due to chrome-plated stainless steel rod in place of chrome-plated alloy steel. ) -H7 is not available in -Z. ) *For mounting accessories and dimensions, see pages D- to D-9. ) Marked options provide additional cylinder flexibility, but do not dimensionally comply with the ISO 6/VDM 56 or ISO 6 specifications. 5) ISO cylinders are of metric design. Imperial dimensions and specifications are provided for convenience. 6) See page D-6 for switch information. 7) On position units, cushion control, and Port Controls are available in locations and 5 only. CYLINDR OPTIONS F - Wrench Flats on Rod F - No Wrench Flats on Rod H6 - Rodlok ready cylinder (CVS only) H7 - Rodlok unit includes locking device daptor and Cylinder preassembled (CVS only) K_ - xtra Rod xtension in 5 mm increments. Length code is K5 = 5 mm, K5 = 5 mm, etc. L9 - NPT Ports M - Magnetic piston for use with PHD Miniature Reed and Magnetoresistive Switches T - Female Rod nd Undersized Thread T55 - Plain Rod nd T - Male Rod with Oversized Thread (CVx only) Z - Corrosion Resistant, chrome-plated Stainless Steel Rod, and appropriate coating on ferrous parts. D- (800) 6-85 www.phdinc.com/cv CT-0
NFITS: SRIS CV CYLINDRS The HUSHCONTROL dvantage Units specified with the Hushcontrol dvantage provide superb speed and deceleration control and environmentally friendly noise levels. Standard mm through 00 mm bore units conform to ISO 6 and VDM 56 specifications. Sizes 0 mm and 5 mm bore conform to ISO 6 for customer interface and mounting dimensions. vailable in 8 bore sizes from 0 mm to 00 mm to fit a wide range of applications. vailable in standard stroke lengths up to 000 mm on CV units, 750 mm on CV units, and 500 mm on CVC units. Internal shock pads are standard on all sizes, eliminating metal to metal contact. Wide range of options, including NPT ports, provides easy selection of cylinders to meet your exact needs. Optional Rodlok securely holds a static piston rod in place at any point of stroke desired. Ideal for applications where rod drift is unacceptable due to system leakage, line rupture, or power loss. Ports, cushion controls, and port controls are available in any combination on any side of the head (extend end) and cap (retract end). D wide range of mounting accessories provides ease of design into application. oth standard and corrosion resistant piston rods have hard chrome plating for maximum life and durability. The versatile design allows flexibility for custom modifications to meet your needs. Optional PHD proximity switches mount easily on any side of the cylinder in the integral switch slots. No brackets are required for switch mounting. Cylinders, including port and cushion controls are easily field repairable, maximizing your investment. SPCIFICTIONS CV & CV CVC WORKING PRSSUR 7.5 psi min. - 50 psi max. 0 psi min. - 50 psi max. [0.5 bar min. - 0 bar max.] [0.67 bar min. - 0 bar max.] LURICTION Permanent for Non-Lube ir or Lubricated ir HDS & CPS nodized luminum lloy CYLINDR TU nodized luminum lloy PISTON ROD Hard Chrome-Plated Steel or Hard Chrome-Plated Stainless Steel ROD RING Internally Lubricated ngineered Polymer PISTON SLS Long Life Urethane Material Long Life Nitrile Material ROD SLS Long Life Urethane Material featuring The HUSHCONTROL dvantage (-P, -D) Only PHD Series CV Cylinders are offered with the Hushcontrol dvantage. Hushcontrol is achieved when optional cushions and Port Controls are ordered with the standard shock pads. This combination provides: Superior speed and deceleration control of piston rod and attached loads. Significantly lowers noise levels even at high cycle speeds. Rodlok Kits and dimensions can be found on pages D- and D-5. PORT CONTROL PHD s Port Control is a built-in flow control valve for regulating the speed of the cylinder through its entire stroke. CUSHION ffective cushion up to.9 in. [0. mm] for smooth deceleration at end of stroke. SHOCK PD uilt-in shock pads are standard on all sizes. liminates metal to metal contact. CT-0 (800) 6-85 www.phdinc.com/cv D-5
DIMNSIONS: SRIS CV CYLINDRS SIZS 0 & 5 mm D THRD.60.9 0 & 5 mm SNOUT JM NUT DIMNSIONS SNOUT JM NUT PR DIN 9 NUT PR DIN 9 M DI f9 G MIN X D X PL X PORT X PC HIDDN LINS RFR TO DOUL ROD UNIT ONLY DI SQ R SQ D THRD ROD JM NUT DIMNSIONS POSITION KK THRD NUT PR DIN 9 SW CROSS WRNCH FLT THRD SNOUT JM NUT PR DIN 9 M C WH f G f9 VD G f8 + STROK X DC WH + STROK (DOUL ROD ONLY) f + STROK (CYLINDR & CYLINDR ) X D X DC X PORT G V (SM S VD ON DOUL ROD UNIT) X PL PC X RT THRD OTH NDS SQ R SQ DI C KK THRD SW CROSS WRNCH FLT THRD WH f VD G CYLINDR CYLINDR f8 + STROK (CYLINDR ) f + STROK (CYLINDR ) V X RT THRD OTH NDS SIZS -00 mm D THRD ROD JM NUT DIMNSIONS NUT PR DIN 9 M F f9 G X PL X PORT HIDDN LINS RFR TO DOUL ROD UNIT ONLY DI X PC SQ R SQ DI C X DC KK THRD SW CROSS WRNCH FLT f WH VD X D G G f f8 + STROK V (SM S VD ON DOUL ROD UNIT) WH + STROK (DOUL ROD ONLY) 8X RT THRD POSITION NUT PR DIN 9 M F f9 G f + STROK (CYLINDR & CYLINDR ) X D X X DC X PL SQ R SQ X PC DI C KK THRD SW CROSS WRNCH FLT VD f G CYLINDR CYLINDR WH f8 + STROK (CYLINDR ) f + STROK (CYLINDR ) V 8X RT THRD D-6 (800) 6-85 www.phdinc.com/cv ll dimensions are reference only unless specifically toleranced. CT-0
D DIMNSIONS: SRIS CV CYLINDRS LTTR DIM min M G min C D DC D PORT** DPTH f f8 f9 f f f G KK PC PL R RT SW V VD WH 0 mm in mm.78.866.5.866.0 M x.5.7.0.57.0 M8 x.5.89.8.58.8.57 7.0.5.669.*..50 6..787.76.079.079.95 G /8 9.0.0.0 8.0 7.0 59.0*.6 89.0 56.0 0.0 M8 x.5.65..5 9.0.0 6.0 M x 0.7 7.0.0.0.0 5 mm in mm.87.866.669.0.0 7.0.0.866 M x.5.7.0.97 5.0 M0 x.5.05 5..559..575 0.0 G /8.5.78.50*..6 6.78.787 8.0 9.0 6.0*.6 9.0 6.0 0.0 M0 x.5.77.5.5 9.0.06 7.0 M x 0.7.5.079.079.0 8.0.0.0 8.0 mm in mm.7.87.8.669 8.9.0 0.0 7.0 0.0.8.709 8.0.97 5.0 M0 x.5.76 7.0.965.5.99 9.5.5.78.70.65.6.70 8.07.0 G /8 8.0 8.5 9.0. 6.0.0 05.0.0 M0 x.5.97 5.0.60 6.0.80.5 M6 x.9.57.77.0 0.0.0.5 6.0 SIZ 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm.8..906.0.78 5.0.78 9.0.78 5.0.709 8.0.6 6.0 M x.5.7 9.5.08 7.5.05 56.0 G /.5 9.0.807 0.5. 05.0.69..56 6.5.8.5 8.957 7.5.58.5 M x.5.6 6.0.78 8.5.96 8.0 M6 x.5.57.77.8.0.0.5 0.0.05.0.575.95.575.787.5.5.00.697.5.08.7..5 5.78 9.90.58.60.57.77.57 in mm.05 6.75.0.0.77 5.0.95.0.77 5.0.787 0.0.5 8.0 M6 x.5.5 9.0.0 0.5.50 80.0 G /8.7.0.08 7.5.76.0. 5.7.5 8.0 6.8 57.0 0.95 78.0.96 8.0 M6 x.5.9 0.0.787 0.0. 56.5 M8 x.5 NOTS: ) Unless otherwise dimensioned, mounting hole patterns are centered on the cylinder. ) Ports and cushions may appear on either side of the cylinder centerline based on option combinations. ) *Dimensions shown are for CVC units. dd to f8 dimension.5 in [8 mm] for CV0 and.6 in [6 mm] for CV5. ) **ll units, except port with port control on same side, comply with DIN 85 part port specifications for short stud and large sealing surface. See port control option sheet for port and port control dimensions on units with ports and port controls on the same side. 6.75.0 0.0.0 0.0 0.0 8.0 M6 x.5 9.0 5.5 68.5 G / 9.0 7.5 06.0 5.7 8.0 5.5 5.5.5 M6 x.5.6 6.0.78 8.5.8 6.5 M8 x.5 6.0.0.5 7.0.60.57.77.57 6.0.0.5 7.0.97.95.55 9.0.77 5.0.8 0.0.77 5.0.787 0.0.9 0.0 M0 x.5.59 5.0.8 0.0.858 98.0 G /8.7.0.9.5 5.09 8.0.68 6.8.9 0.0 6.77 7.0.8 00.0.96 8.0 M0 x.5.9 0.0.709 8.0.85 7.0 M0 x.5.87.57.77.8.0.0.5 6.0.97.95.55 9.0.65 55.0.8 0.0.65 55.0.787 0.0.9 0.0 M0 x.5.60 6.0.9.0.58 5.0 G /.55.0.7 6.5 5. 8.0.68 6.8.9 0.0 7.008 78.0. 6.0.65.0 M0 x.5.7.0.866.0.50 89.0 M0 x.5.87.57.77.008.0.0.5 5.0 ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cv D-7
NGINRING DT: SRIS CV CYLINDRS D PRSSUR RTINGS ll Series CV and CV Cylinders have an operating pressure range of 7.5 psi minimum to 50 psi maximum [0.5 to 0 bar]. Pressure range for CVC units is 0 psi minimum to 50 psi maximum [0.67 to 0 bar]. SLS Series CV Cylinders utilize urethane and Nitrile seals which are compatible with standard paraffin-based lubrication oils used for pneumatic cylinders. For compatibility with other fluids, consult PHD. TMPRTUR LIMITS Series CV Cylinders are designed for use in temperatures from -0 to 80 F [-9 to +8 C]. For temperatures outside this range, consult PHD. STROK TOLRNC Tolerance on the nominal stroke dimension is related to the bore size and stroke length as shown in the following table: LURICTION ll units are prelubricated at the factory for service under normal operating conditions. Cylinders can be used with nonlubricated air; however, use with lubricated air will extend life. mm CVx0 CVx5 CVCx0 CVCx5 0 50 6 80 00 S WIGHT lb kg.55.69.5.66.5.08.8.87 7.78.0 CYLINDR WIGHT TL.5...0.66.9.9..5 5.00 DDR PR " [5 mm] STROK lb kg.0..0..7...6.5.60.0.05.0.05.08.0.5.6..7 mm 0 & 5, 0, & 50 6, 80, & 00 NOMINL STROK (L) in mm L L > L 0 L > 0 L 0 L > 0 L 00 L > 00 L 500 L > 500 L 500 L > 500 NOMINL STROK CYL. FULL STROK TOLRNC in mm + 0.059/-0 + 0.079/-0 + 0.079/-0 + 0.6/-0 + 0.098/-0 + 0.57/-0 +.5/-0 +.0/-0 +.0/-0 +./-0 +.5/-0 +.0/-0 NOMINL STROK POSITION STROK TOLRNC in mm + 0.059/-.06 + 0.079/-.06 + 0.079/-.050 + 0.6/-.050 + 0.098/-.070 + 0.57/-.070 +.5/-. +.0/-. +.0/-. +./-. +.5/-.8 +.0/-.8 LIF XPCTNCY Series CV and CV Cylinders have been tested to 0 million trouble-free cycles. Series CVC units will have shorter life due to Nitrile piston seals in place of Urethane seals. Operation with lubricated air can extend cylinder life. MINTNNC s with most PHD products, these cylinders are field repairable. Repair kits, piston and rod assemblies, port control cartridge assemblies, and main structural components are available as needed for extended service. D-8 (800) 6-85 www.phdinc.com/cv CT-0
NGINRING DT: SRIS CV CYLINDRS CYLINDR SPDS The cylinder speed and time required for the cylinder to extend or retract are dependent upon many application conditions including supply line pressure, valve rating, line size, attached tooling, flow controls, etc. Upon actuation, the cylinder will accelerate from rest to some final speed prior to end of stroke. This is illustrated by the pproximate xtend or Retract Time (seconds) XMPL 50 mm bore cylinder with 00 mm stroke quation not applicable for imperial values. mm 0 5 0 50 6 80 00 [] CCLRTION TIM s 0.05 0.0 0.07 0.0 0.05 0.056 0.079 0.075 Standard & Cushion Unit + Stroke - 000 x C.05 + 00-8 000 x.0 STNDRD & CUSHION UNITS [] STROK DURING CCLRTION in mm..8...9... 58 6 8 0 0 6 [C] TYPICL CYLINDR SPD in sec m/sec 5.08.8.67.0.0 0.89 0.6 0.6 Port Control Unit (full open) PORT CONTROL UNITS (FULL OPN) [D] CCLRTION TIM s 0.065 0.0 0.0 0.09 0.59 0.6 0. 0. NOTS: The above speed data is based on: ) No attached load with a line pressure of 80 psi [5.5 bar] with a valve rated at Cv=9.0. ) 0 mm and 5 mm cylinders tested with 0.7" ID tubing. ) mm and 0 mm cylinders tested with 0.8" ID tubing. ) 50 mm, 6 mm, and 80 mm cylinders tested with 0.8" ID tubing. 5) 00 mm cylinders tested with two 0.8" ID tubes to each port from the valve. D + Stroke - 000 x F = 0. sec.59 + 00-5 = 0. sec 000 x 0.5 00 50 05 80 80 5 5 5 graph below. Using the data in the table below, the total time to extend or retract can be approximated. ctual extend and retract times will vary, especially as the application conditions change from those stated below. [] STROK DURING CCLRTION in mm..5.....0. 8 5 6 5 58 5 56 Cylinder Speed LNGTH SPD 0 0 IDLIZD CYLINDR SPD cceleration Typical Cylinder Speed Time [F] TYPICL CYLINDR SPD in/sec m/sec 5 6 5 8 0 0.89 0.6 0.8 0.9 0.5 0.6 0.6 0.5 MTRIC TO IMPRIL CONVRSION MULTIPLY Y TO OTIN mm.09 in m/sec 9.7 in/sec D CT-0 (800) 6-85 www.phdinc.com/cv D-9
NGINRING DT: SRIS CV CYLINDRS LNGTH FORC PRSSUR IMPRIL TO MTRIC CONVRSION MULTIPLY Y TO OTIN in 5. mm lbs.5 N psi 0.069 bar MTRIC TO IMPRIL CONVRSION MULTIPLY Y TO OTIN mm N bar 0.09 0.5.5 in lbs psi D HOW TO DTRMIN CORRCT CYLINDR SIZ Step. Determine stroke and force required for the application. ROD ND CONDITION CYLINDR MOUNT COLUMN STRNGTH CURV STROK FCTOR K Step. Determine the force produced by the cylinder using the graphs on page D-. The cylinder force graphs are based on the following formulas and the data from the cylinder force table. IMPRIL MTRIC F = P x F = 0. x P x F = Cylinder Force lbs N P = Operating Pressure psi bar = ffective rea in mm (Push or Pull) DI in mm 0.787 0.98.60.575.969.80.50.97 0 5 0 50 6 80 00 CYLINDR FORC TL ROD DI in mm 0.5 0.9 0.7 0.60 0.787 0.787 0.98 0.98 8 0 6 0 0 5 5 ROD DIRCTION PUSH PULL PUSH PULL PUSH PULL PUSH PULL PUSH PULL PUSH PULL PUSH PULL PUSH PULL FFCTIV R in mm 0.9 0. 0.76 0.6.5.07.95.6.0.56.8. 7.79 7.0.7. 6 9 80 69 57 056 96 69 7 80 507 56 785 76 NOT: Use pull forces for calculating double rod end performance. Step. For the selected cylinder, verify that there is sufficient rod column strength based on the cylinder extend force and stroke length. Rod column strength curves are based on the following formula: F c = π I (LK) Sf IMPRIL MTRIC Fc= Maximum Column Force lbs N = Modulus of lasticity 0 x 0 6 psi 07 GPa L = Stroke Length in mm I = Moment of Inertia in mm = π (Rod Diameter) /6 K = Stroke Factor (see chart) (see chart) Sf= Safety Factor 5 5 Fixed & Supported Pivoted & Guided Pivoted & Guided Fixed & Guided xample: Step. For a specific application, it has been determined that a cylinder is required to operate within the following parameters: P = Operating Pressure = 80 psi [5.5 bar] F = Required xtend Force = 50 lbs [667 N] L = Required Stroke = 0 in [76 mm] V = Required Maximum Velocity = 0 in/sec [.5 m/sec] M = ttached Load = 75 lbs [5 kg] Mounting type: Fixed Pivot at Rear Fixed Fixed NOT: In these two cases, column strength is sufficient for stroke lengths less than or equal to 0 in [000 mm] for CV units and 0 in [750 mm] for CV and CVC units. Rod end is pivoted and guided Cylinder is pivoted at rear Step. Using the Cylinder Force Charts on page D-, locate 80 psi [5.5 bar] on the horizontal axis. Follow the line vertically until it intersects the solid (extend) diagonal line on the chart. The mm cylinder extend force is only 00 lbs [5 N] at 80 psi [5.5 bar] less than the required 50 lbs [667 N]. The 0 mm is capable of just over 50 lbs [667 N] extend force at this pressure. Select the 0 mm and proceed to the next step. Step. Check column strength. ased on the mounting types, use curve on the 0 mm Rod Column Strength Chart (see page D-). t 50 lbs [667 N] extend force, the maximum allowable cylinder stroke is 7 in [686 mm]. However, the required stroke is 0 in [76 mm]. ssuming the stroke cannot be changed, it is necessary to select a cylinder with a larger rod diameter. Checking the 50 mm cylinder in the same way as was done for the 0 mm shows that the 50 mm cylinder is acceptable. Step. Using the Kinetic nergy charts on page D-, find the point on the 50 mm chart that corresponds to the given maximum velocity and attached load. The chart shows that the cylinder must be specified with cushions to properly decelerate the load. See Note See Note 0.7 0.5 D-0 (800) 6-85 www.phdinc.com/cv CT-0
NGINRING DT: SRIS CV CYLINDRS MXIMUM LLOWL KINTIC NRGY GRPHS 0 [.0] 0 mm ore 0 [.0] 5 mm ore Velocity in/sec [m/sec] 00 [.5] 80.0 [.0] 60.0 [.5] 0.0 [.0] 0.0 [.5] Cylinder Only Cylinder with Cushion Velocity in/sec [m/sec] 00 [.5] 80 [.0] 60.0 [.5] 0.0 [.0] 0.0 [.5] Cylinder Only Cylinder with Cushion D 0 0 0 [.5] 0 [9.] 0 [] 0 [8] 50 [] 60 [7] 0 0 0 [.5] 0 [9.] 0 [] 0 [8] 50 [] 60 [7] 70 [] Total ttached Load lb [kg] Total ttached Load lb [kg] Velocity in/sec [m/sec] 00.0 [.5] 80.0 [.0] 60.0 [.5] 0.0 [.0] 0.0 [.5] 0 0 5 [] mm ore 50 [] Cylinder Only Cylinder with Cushion 75 [] 00 [5] 5 [57] Velocity in/sec [m/sec] 80.0 [.0] 70.0 [.8] 60.0 [.5] 50.0 [.] 0.0 [.0] 0.0 [.76] 0.0 [.5] 0.0 [.5] 0 0 5 [] 50 [] 0 mm ore 75 [] Cylinder Only Cylinder with Cushion 00 [5] 5 [57] 50 [68] 75 [79] 00 [9] Total ttached Load lb [kg] Total ttached Load lb [kg] Velocity in/sec [m/sec] 80.0 [.0] 70.0 [.8] 60.0 [.5] 50.0 [.] 0.0 [.0] 0.0 [.76] 0.0 [.5] 0.0 [.5] 0 0 50 [] 00 [5] 50 mm ore Cylinder Only Cylinder with Cushion 50 [68] 00 [9] Total ttached Load lb [kg] 50 [] 00 [6] Velocity in/sec [m/sec] 60.0 [.5] 50.0 [.] 0.0 [.0] 0.0 [.76] 0.0 [.5] 0.0 [.5] 0 0 50 [] 00 [5] 6 mm ore 50 [68] Cylinder Only Cylinder with Cushion 00 [9] 50 [] Total ttached Load lb [kg] 00 [6] 50 [59] 00 [8] 60.0 [.5] 80 mm ore 60.0 [.5] 00 mm ore Velocity in/sec [m/sec] 50.0 [.] 0.0 [.0] 0.0 [.76] 0.0 [.5] 0.0 [.5] Cylinder Only Cylinder with Cushion Velocity in/sec [m/sec] 50.0 [.] 0.0 [.0] 0.0 [.76] 0.0 [.5] 0.0 [.5] Cylinder Only Cylinder with Cushion 0 0 50 [] 00 [5] 50 [68] 00 [9] 50 [] 00 [6] 50 [59] 00 [8] 50 [0] 500 [7] 550 [9] 0 0 75 [] 50 [68] 5 [0] 00 [6] 75 [70] 50 [0] 55 [8] 600 [7] 675 [06] 750 [0] Total ttached Load lb [kg] Total ttached Load lb [kg] CT-0 (800) 6-85 www.phdinc.com/cv D-
NGINRING DT: SRIS CV CYLINDRS CYLINDR FORC CHRTS ROD COLUMN STRNGTH CHRTS Push Pull D Force lbs [N] 5 [556] 00 [5] 75 [] 50 [] 5 [] 0 & 5 mm ore 0 & 5 mm ore 5 mm 0 mm Force lbs [N] 0 [5] 00 [5] 80 [56] 60 [67] 0 [78] 0 [89] 5 mm () 0 mm () 0 0 5 [.7] 50 [.5] 75 [5.7] Pressure psi [bar] 00 [6.90] 5 [8.6] 50 [0.] 0 0 5 [5] 0 [50] 5 [75] 0 [500] Maximum Cylinder Stroke inch [mm] 5 [65] 0 [750] 00 [890] mm ore 00 [890] mm ore Force lbs [N] 50 [667] 00 [5] Force lbs [N] 50 [667] 00 [5] 50 [] 50 [] 0 0 5 [.7] 50 [.5] 75 [5.7] Pressure psi [bar] 00 [6.90] 5 [8.6] 50 [0.] 0 0 [00] 8 [00] [00] 6 [00] 0 [500] [600] 8 [700] [800] Maximum Cylinder Stroke inch [mm] 5 [900] 9 [000] 00 [] 50 [] 0 mm ore 00 [] 50 [] 0 mm ore Force lbs [N] 00 [890] 50 [667] 00 [5] Force lbs [N] 00 [890] 50 [667] 00 [5] 50 [] 50 [] 0 0 5 [.7] 50 [.5] 75 [5.7] Pressure psi [bar] 00 [6.90] 5 [8.6] 50 [0.] 0 0 [00] 8 [00] [00] 6 [00] 0 [500] [600] 8 [700] [800] Maximum Cylinder Stroke inch [mm] 5 [900] 9 [000] Force lbs [N] 800 [558] 600 [669] 00 [779] 00 [890] 0 0 5 [.7] 50 mm & 6 mm ore 50 [.5] 75 [5.7] Pressure psi [bar] 00 [6.90] 6 5 [8.6] 50 50 [0.] Force lbs [N] 800 [558] 700 [] 600 [669] 500 [] 00 [779] 00 [] 00 [890] 00 [5] 0 0 [00] 8 [00] [00] 50 mm & 6 mm ore 6 [00] 0 [500] [600] 8 [700] [800] Maximum Cylinder Stroke inch [mm] 5 [900] 9 [000] Force lbs [N] 000 [8896] 600 [77] 00 [58] 800 [558] 00 [779] 0 0 5 [.7] 80 mm & 00 mm ore 50 [.5] 75 [5.7] Pressure psi [bar] 00 [6.90] 00 5 [8.6] 80 50 [0.] Force lbs [N] 000 [8896] 600 [77] 00 [58] 800 [558] 00 [779] 0 0 [00] 8 [00] 80 mm & 00 mm ore [00] 6 [00] 0 [500] [600] 8 [700] [800] Maximum Cylinder Stroke inch [mm] 5 [900] 9 [000] D- (800) 6-85 www.phdinc.com/cv CT-0
OPTIONS: SRIS CV CYLINDRS D D DR CUSHION CONTROL IN OTH DIRCTIONS (standard location & 5, see note) CUSHION CONTROL ON XTND ONLY (standard location, not available on position units) CUSHION CONTROL ON RTRCT ONLY (standard location 5, not available on position units) Cushion Control Locations - oth ends - xtend end only R - Retract end only PHD cushions are designed for smooth deceleration at the end of stroke. When the cushion is activated, the remaining volume in the cylinder must exhaust past an adjustable needle which controls the amount of deceleration. The effective cushion lengths for each bore size are shown in the table below. To specify different cushion control locations on the head or cap, see option code above. Note: Cushion controls on position units are available in locations and 5 only and as -D only. position units will have cushion on full extend and full retract only. CUSHION CONTROL OPTIONS -D x x x xtend Location (,,, ) Omit if -DRx Retract Location (5, 6, 7, 8) Omit if -Dx XTND ND 8 7 5 RTRCT ND Unit shown is -D5, cushion in location on extend end and cushion in location 5 on retract end. (Ports are shown in standard locations & 5.) Cushion control locations on position 5 units are and 5 only and will 8 receive a control on the head and intermediate head only. RTRCT ND 6 6 D DC LTTR DIM DC D DH FFCTIV CUSHION LNGTH D DH HX CROSS FLTS D DC SOM PORT CONTROL & CUSHION OPTION COMINTIONS WILL MOV CUSHION CONTROLS TO THIS LOCTION 0 mm in mm.89.58..8.8.5. 5 mm in mm.05.559.69 5...5.9 XTND ND Unit shown is -DR6, cushion in location 6 on retract end and none on extend end. (Ports are shown in standard locations & 5.) SIZ mm 0 mm 50 mm 6 mm 80 mm in mm in mm in mm in mm in mm.76.965.598 7.0.5.5 5..7.08.807 9.5 7.5.5 0.5.5.0.870 9.0 6.5.5..5.0.80 9.0 0.5.5 0..59.8.89 5.0 0.0.0.7 7 00 mm in mm.60.9.89 6.0.0.0 0. F WRNCH FLTS ON ROD ND With this option, the rod is supplied with four rod end flats instead of the standard two flats. If this option is specified on double rod units, both rod ends will be supplied with four wrench flats. F NO WRNCH FLTS ON ROD ND This option omits rod end wrench flats. If this option is specified on double rod units, both rod ends will be supplied without wrench flats. F STNDRD F This option does not dimensionally comply with the ISO 6/VDM 56 or ISO 6 specifications. ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cv D-
OPTIONS: SRIS CV CYLINDRS H6 RODLOK RDY CYLINDR vailable on single rod units only. (Rodlok sold separately) D H7 RODLOK CYLINDR & RODLOK vailable on single rod units only. (preassembled) PHD s Rodlok is ideal for locking the piston rod while in a static/stationary position. When the pressure is removed from the port of the Rodlok, the mechanism will grip the rod and prevent it from moving. The loads are held indefinitely without power. The Rodlok may also be used in intermittent dynamic use as a pressure off piston rod deceleration device. Rodlok performance (ccuracy and Stopping distance) is application and environment sensitive (Cleanliness of rod or Rodlok will also affect performance). TH RODLOK IS NOT DSIGND TO USD S PRSONNL SFTY DVIC. Option H6 provides a Rodlok ready cylinder with appropriate rod extension and materials for use with PHD s Rodlok. Option H7 provides a cylinder and Rodlok pre-assembled. The port for the Rodlok will be assembled in the same position as the port on the extend end of the cylinder. The Rodlok locking device and adaptor can be purchased separately as kits. See chart at right. The locking device and adaptor are not available with the -Z corrosion resistant finish. Dimensions continued on next page. mm 0 5 0 50 6 80 00 STTIOCKING FORC* lb N 79 90 5 5 7 95 67 50 00 600 000 500 00 000 5000 DYNMIC LOCKING FORC ctual dynamic locking forces are application sensitive. nvironmental conditions, load weights, attitude, pressure, and speed influence performance. NOT: *Locking force given in table is the actual locking force with a dry clean rod and does not include any safety factor. mm 0 5 0 50 6 80 00 LOCKING DVIC KIT 659-07- 659-08- 659-0- 659-0- 659-0- 659-0- 659-05- 659-06- RODLOK KITS DPTOR KIT* 660-07- 660-08- 660-0- 660-0- 660-0- 660-0- 660-05- 660-06- COMPLT RODLOK * 66-07- 66-08- 66-0- 66-0- 66-0- 66-0- 66-05- 66-06- NOTS: ) *Kits ship with cylinder mounting hardware. ) Rodlok is intended for use only on -H6 cylinder. ) Imperial port adaptor converts port from G/8 to /8" NPT for use with -L9 cylinders Plumbing Schematic xample: OPTIONL PRSSUR SNSOR/SWITCH IMPRIL PORT DPTOR 665-665- 665-665- 665- OPRTING PRSSUR The operating pressure for the locking device is different than the operating pressure for the cylinder with the Rodlok attached. The locking device of the Rodlok is designed with an operating pressure range of 60 psi minimum to 50 psi maximum [ to 0 bar]. The Series CV Cylinder with a Rodlok attached has an operating pressure range of psi minimum to 50 psi maximum [.5 to 0 bar]. This option does not dimensionally comply with the ISO 6/VDM 56 or ISO 6 specifications. The pneumatic schematic above shows typical valving for cylinder and Rodlok for both horizontal and vertical operation. The schematic shows three / way valves, one for each port on the cylinder and one for the Rodlok port. The use of two valves on the cylinder allows for both ports to be pressurized when valves are deenergized. The use of an in-line regulator allows the cylinder ports to be pressurized at different pressures. This allows the cylinder to balance out the opposing pressure and force of the attached load. Once piston rod motion has stopped, the Rodlok can be engaged by de-energizing its valve and releasing its pressure. The use of check valves and built in PHD Port Controls is recommended. Pressure switch shown is optional and application specific. D- (800) 6-85 www.phdinc.com/cv CT-0
OPTIONS: SRIS CV CYLINDRS RODLOK DIMNSIONS (continued from previous page) G PORT SQ L8 L L6 L5 L7 H X G THD WH X F FSTNR f8 + STROK D F C Ø D Ø DK D THRD L X D MIN LONG (0 & 5 ONLY) X G THD X DPTH L0 L LTTR DIM C D D D DK F F G G G H L L L5 L6 L7 L8 L0 L WH 0 mm in mm.0 6.0.57 7.0.57 7.0.866.0 M x.5.590.5.787.78 8.5 M x 0.7 x 0 M x 0.7 M5.795.5.5.575....50.95 5.0 8.0 0.0 7.0 9.0 9.0 0.0 57.0 9.0.0 6.0.0 5 mm in mm.06 7.0.575 0.0.575 0.0.866.0 M x.5.669.9.787.787 0.0 M x 0.7 x 0 M x 0.7 M5.85.5.5.7.80.0.5.85.0 7.0 0.0 0.0 7.5 8.0 8.0.0 6.0.0.0 7.0 8.0 NOTS: ) -H7 units have Rodlok port aligned with cylinder port on extend. ) See page D-6 for complete cylinder dimensions. SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm.80.575.65.60.890.969.8.7.866.98 5.0 M6 x x 0 M6 x M5 M5.6.5.7.890.8.60.60.5.9.0.5 0.0. 6.0 8.0 50.0 0.0.0.0 85.0 8.0.0 8.0 58.0.0 6.0 8.0 7.0 6.0.96.8.77.87.05.8.78.60.0. 9.0 M6 x x 0 M6 x M5 G /8.89.9.7.65.559.98.768.9.6.8 8.0 6.0.5.0 56.0 58.0 5.0 6.0 6.0 97.5 0.0.0 55.0 65.0 5.5 9.5 0.0 85.0 0.0.8.6.5.95.677.756.575.787.60.78 5.0 M8 x.5 x 0 M8 x.5 M6 G /8.66.59.60.756.8.99.87.7..57 6.5 5.0.5.0 68.0 70.0 0.0 0.0.0 7.5 5.0 6.0 70.0 8.0 9.0.0.0 07.0 7.0..65.95.60.8.6.77.787.55.67.5 M8 x.5 x 0 M8 x.5 M8 G /8 5.56.59.59.756.8.99.87.7..57 56.5 55.0 7.5.0 8.0 85.0 5.0 0.0 9.0.5 5.0 5.0 70.0 8.0 9.0.0.0 07.0 7.0.85.756.9.7.97..77.98.7.067 5.5 M0 x.5 x 0 M0 x.5 M8 G /8 6.75.60.60.5...0.60 5.5.8 7.0 70.0 0.0.0 00.0 05.0 5.0 5.0.0 7.5 6.0 6.0 90.0 0.0 6.0 8.0 6.0 6.0 6.0.50.756.9.6.7 5.8.65.98.99 89.0 70.0 0.0 60.0 0.0 0.0 55.0 5.0 9.0.559 65.0 M0 x.5 x 0 M0 x.5 M8 G /8 7..60.709.6.58.559.06.60 5.60.008 89.0 6.0 8.0 9.0 5.0 65.0 7.0 6.0.0 5.0 L9 NPT PORTS This option provides NPT ports instead of the standard SPP ports. The NPT ports are located in the same location as the SPP ports. This option does not dimensionally comply with the ISO 6/VDM 56 or ISO 6 specifications. [mm] 0 5 0 50 6 80 00 OPTIONL NPT PORT /8* /8* /8 / / /8 /8 / STNDRD SPP PORT G /8* G /8* G /8 G / G / G /8 G /8 G / *When port controls are specified on the same face as ports, the standard metric port is M5 and the -L9 option provides a 0- port. ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cv D-5
OPTIONS: SRIS CV CYLINDRS D K_ XTR ROD XTNSION xtra rod extension can be achieved by specifying the option -K followed by the length code. Rod extension is available in 5 mm increments. If this option is specified on double rod units, both rod ends will be supplied with the same extra rod extension. Contact PHD for other combinations. Length code examples K5 = 5 mm of extra rod extension K5 = 5 mm, etc. WH + K_ K_ This option does not dimensionally comply with the ISO 6/VDM 56 or ISO 6 specifications. [mm] 0 5 0 50 6 80 00 in 0.95.0.0.8.57.57.8.008 WH mm.0 8.0 6.0 0.0 7.0 7.0 6.0 5.0 Z CORROSION RSISTNT y specifying this option, a stainless steel rod with hard chrome plating is supplied in place of the standard hard chrome plated steel material. ppropriate coating is supplied on ferrous parts. M MGNT FOR PHD MINITUR RD ND MGNTORSISTIV SWITCHS SRIS 650 MGNTORSISTIV SWITCHS PRT NO. DSCRIPTION COLOR 6505--0 6506--0 655-656- NPN (Sink) DC Magnetoresistive, m cable PNP (Source) DC Magnetoresistive, m cable NPN (Sink) DC Magnetoresistive, Quick Connect PNP (Source) DC Magnetoresistive, Quick Connect rown Tan rown Tan This option equips the cylinder with a magnetic band on the piston for use with PHD Miniature Reed and Magnetoresistive Switches listed below. These switches mount easily to the cylinder using T slots in the body. See Switches and Sensors section in PHD s main catalog for complete switch information. Three position units will receive a magnet on both cylinder and cylinder when specified with -M option. PRT NO. DSCRIPTION COLOR 6507--0 657- SRIS 650 RD SWITCHS G C/DC Reed, m cable C/DC Reed, Quick Connect Silver Silver D F C Connector Detail.6.00.70 CL.870.55 SQ SQ* D F C SQ SQ D F C SQ* SQ Connector Detail H I 0 & 5 mm units, 0, & 50 mm units 6, 80, & 00 mm units LTTR 0 mm DIM in mm * C D F G H I.9..8.6.57.7.870..0 8.7 7. 6.0 7.0 9.5. 0.8.9...6.575.7.870. NOT: *ISO/VDM max square size 5 mm in mm.0. 8. 6.0 0.0 9.5.. SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm.969.76.95.6.99.7.870.6 50.0 7.0 7.5 6.0 9.5 9.5. 9..8.97.56.6.05.7.870.087 58.0 5.0 6.5 6.0 56.0 9.5. 7.6.756.6.76.6.697.7.870.06 70.0 6.0 7.0 6.0 68.5 9.5. 8..6.6.5.6.50.7 7.8.059 85.0 6.0 8.5 6.0 80.0 9.5 7. 6.9..57.95.6.858.7 0.89.965 05.0.0 7.5 6.0 98.0 9.5 0 0.8.5 5.8.00.5.6.58.7.795.8 0.0 0.5 8.0 6.0 5.0 9.5 0. 0.6 D-6 (800) 6-85 www.phdinc.com/cv ll dimensions are reference only unless specifically toleranced. CT-0
OPTIONS: SRIS CV CYLINDRS P P PR PORT CONTROLS ON OTH NDS (standard location & 5, see note) PORT CONTROLS ON XTND ONLY (standard location, not available on position units) PORT CONTROLS ON RTRCT ONLY (standard location 5, not available on position units) 8 5 PORT CONTROL OPTIONS -P x x x Port Control Locations - oth ends - xtend end only R - Retract end only xtend Location (,,, ) Omit if -PRx Retract Location (5, 6, 7, 8) Omit if -Px PHD s Port Control is a built-in flow control for regulating the speed of the cylinder through its entire stroke. The Port Control operates on the meter-out principle and features an adjustable needle in a cartridge with a check seal. The self-locking needle has micrometer threads and is adjustable under pressure. The needle determines the orifice size which controls the exhaust flow rate of the actuator. The check seal expands while air is exhausting from the actuator, forcing the air to exhaust past the adjustable needle. The check seal collapses to allow a free flow of incoming air. The PHD Port Control saves space and eliminates the cost of fittings and installation for external flow control valves. See engineering data for cylinder speeds with PHD s Port Controls. Refer to option code below to specify port control locations. Three position port control locations are and 5 only and will receive a control on the head, intermediate head, and cap. NOTS: Port controls are not available on same end which has -U0x or -Ux0 (four ports) specified. Three position units are available only with -P and only in locations and 5. For, 0, 50, and 6 mm, the port control extends beyond VDM specified square size. See dimension P. 8 5 D XTND ND LTTR DIM ** P CP PCS* PH PLS* SR SR SQ** SQ 0 mm in mm.9.5.8.57 0-.76.57.9 7.0..7 7.0 M5 7.0.5.5 8. RTRCT ND 6 Unit shown is -P5, port control in location on extend end and port control in location 5 on retract end. (Ports shown in standard locations & 5.) PCS* P CP 5 mm in mm.9.5.7.575 0-.76.57.9.0.9 6.9 0.0 M5 7.0.5.5 8. PH HX CROSS FLTS PLS* SR (LL UNITS WITH SPP PORTS, XCPT PORT WITH PORT CONTROLS ON SM SID, (XCPT 0 & 5 mm UNITS), COMPLY WITH DIN 85 PRT FOR LRG SLING SURFCS.) SR (0 & 5 mm UNITS WITH SPP PORTS ND UNITS WITH PORT CONTROLS ND PORT ON SM SID. LL SPP PORTS COMPLY WITH DIN 85 PRT FOR SMLL SLING SURFCS.) PLS* PORT SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm.969.77.69.99.97.866.78.657 G/8 50.0.5. 9.5 5.0.5.0 9.0 6.7.8.0.0.05.6.95.98.87 G/ 58.0 6. 5. 56.0 6.0.5.5 5.0.0.756.0.08.697.6.906.98.95 70.0.8. 68.5 6.0.5.0 5.0.0.6.0.0.50.9.98.0.95 PCS* 85.0 5..6 80.0..0 5.0 8.0.0.. -.00.858.5.0.0.06 05.0. -0. 98.0.0.0 6.0 8.0 7.0 5.8.05 -.09.58 NOTS: )*Dimensions shown are for units with port and port control in the same location. For units with other port and port control combinations, standard port location dimensions apply. Ports may be located on either side of the cylinder centerline depending on port control and cushion option combinations. )**VDM max square size ) Port shown is for when port control is specified in the same location as the port. For all other port control locations the port is the standard G/8. XTND ND G/ 7 G/8 RTRCT ND 6 Unit shown is -PR6, port control in location 6 on retract end and none on extend end. (Ports shown in standard locations & 5.) This option does not dimensionally comply with the ISO 6/VDM 56 or ISO 6 specifications. G/8.906..9.99 G/ 0.0 5. -. 5.0.0 6.0 9.0.0.0 ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cv D-7
OPTIONS: SRIS CV CYLINDRS D U LTRNT PORT LOCTION (not available on position units) With this option, alternate port locations can be specified, providing increased flexibility and customer convenience. See option code below to specify port locations. Three position units available with ports in standard locations and 5 only. XTND ND (HD) 8 7 5 RTRCT ND (CP) 6 Unit shown is -U5, port in location on extend end and port in location 5 on retract end. XTND ND (HD) PORT LOCTION OPTIONS -U x x xtend Location (Head) (0,,,, ) 0 = ll four sides 8 7 5 RTRCT ND (CP) 6 Retract Location (Cap) (0, 5, 6, 7, 8) 0 = ll four sides PORTS ON LL SIDS (0 IN PORT OPTION COD) NOT VILL WITH PHD PORT CONTROLS ON SM ND Unit shown is -U0, port in location on extend end, and ports on all sides on retract end. (Not available with PHD port controls on retract.) T FML ROD ND T55 PLIN ROD ND This option provides a female rod end in place of the standard male rod end. See catalog dimensional pages for standard rod ends. This rod end deviates from ISO 6/VDM 56 or ISO 6. Double rod units will receive the same rod end on both rods unless otherwise specified as shown in the double rod option description. T LTTR DIM L D f K K5 DD min WH 0 mm in mm.5.97..95 ML OVRSIZ ROD ND This option provides a male oversize thread rod end in place of the standard male rod end. See catalog dimensional pages for standard rod ends. Double rod units will receive the same rod end on both rods unless otherwise specified as shown in the double rod option description. 8.00 5.0 M5 x 0.8 0.5.0 5 mm in mm.75*.6.9.0 9.5* 6.0 M6 x.0.5 8.0 This option provides a plain rod end with wrench flats. Standard PHD Series CV Cylinders are supplied with a male rod end. This rod end deviates from ISO 6/VDM 56 or ISO 6. Double rod units will receive the same rod end on both rods unless otherwise specified as shown in the double rod option description. f Ø D T FML ROD ND T ML OVRSIZ ROD ND WH K5 THRD f L T55 PLIN ROD ND Ø D K THD x DD MIN DP SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm.87.7.6.55.0.0.5 6.0 M8 x.5 M x.5.0 6.0.906.599.56.669.8 *Dimension shown is for -T rod end only. -T55 option dimension is.9 in [0.0 mm]..0 5. 6.5 M0 x.5 M6 x.5 7.0 0.0.0.757.5.78.57.0 9. 8.0 M x.75 M0 x.5 9.0 7.0.0.757.5.78.57.0 9. 8.0 M x.75 M0 x.5 9.0 7.0.55.95.9.87.8 9.0. 0.0 M6 x.0 M x.0 6.0 Ø D f WH.55.95.9.87.008 WH 9.0. 0.0 M6 x.0 M x.0 5.0 Unit shown is -T5, plain on extend end and male thread per VDM 56 on retract end. XTND ND RTRCT ND DOUL ROD ND OPTIONS -T x x xtend nd = Male thread VDM 56 (Standard) = Female undersized thread 5 = Plain Retract nd = Male thread VDM 56 (Standard) = Female undersized thread 5 = Plain This option does not dimensionally comply with the ISO 6/VDM 56 or ISO 6 specifications. D-8 (800) 6-85 www.phdinc.com/cv ll dimensions are reference only unless specifically toleranced. CT-0
MOUNTING STYLS: SRIS CV CYLINDRS P&Q PIVOT MOUNT ON SIZS 0 & 5 ONLY This style specifies a pivot mount cap. This style conforms to ISO 6 customer interface and overall unit length when specified with optional -P or -Q mounting. Pivot pins and base mounting brackets are available, see mounting section. LTTR DIM/ TOLRNC CD/H9 W/d L MIN XC/** (*) 0 mm in mm 0.866.0 SIZ 5 mm in mm 0.866.0 M x.5 M x.5 8.0 0.5 6.0 0.60.0 0.7 95.0.09 0.5 0.60 0.7.70 8.0 6.0.0 0.0 NOTS: ) *Dimensions shown are for CVC units. dd to XC dimension.5 in [8 mm] for CV0 and.6 in [6 mm] for CV5. )**±.09 in [± mm] D XC + STROK L RR PIVOT LOCTION 5 Ø CD P THRD Ø W RR PIVOT LOCTION 6 Q CT-0 (800) 6-85 www.phdinc.com/cv D-9
MOUNTING STYLS: SRIS CV CYLINDRS V STNDRD MOUNTING (iso 6/vdma 56 & ISO 6) D WF/WH WG/f f8 + STROK R SQ M KK THRD THRD X RT THRD OTH NDS G DP DI LTTR DIM/ TOLRNC M G min f8 KK R RT WF WH WG f 0 mm in mm 0.78 9.0 0.866.0 M x.5 0.7.0.* 59.0* M8 x.5.0 6.0 M x 0.7 0.95.0 0.669 7.0 5 mm in mm 0.87.0 0.866.0 M x.5 0.7.0.50* 6.0* M0 x.5.06 7.0 M x 0.7.0 8.0 0.78 9.0 *Dimensions shown are for CVC units. dd to f8 dimension.5 [8 mm] for CV0 and.6 in [6 mm] for CV5. SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm 0.87.0.8 0.0 0.709 8.0.70 9.0 M0 x.5.80.5 M6 x.0 6.0 0.78 8.5 0.906.0.78 5.0 0.709 8.0. 05.0 M x.5.96 8.0 M6 x.8 0.0 0.807 0.5.0.0.575 0.0 0.787 0.0.7 06.0 M6 x.5.8 6.5 M8 x.5.57 7.0.08 7.5.0.0.77 5.0 0.787 0.0.76.0 M6 x.5. 56.5 M8 x.5.57 7.0.08 7.5.55 9.0.77 5.0 0.787 0.0 5.09 8.0 M0 x.5.85 7.0 M0 x.5.8 6.0.9.5.55 9.0.65 55.0 0.787 0.0 5. 8.0 M0 x.5.50 89.0 M0 x.5.008 5.0.7 6.5 D-0 (800) 6-85 www.phdinc.com/cv CT-0
D MOUNTING CCSSORIS: SRIS CV CYLINDRS SLF-LIGNING PISTON ROD COUPLRS - MTRIC New metric rod couplers are an ideal accessory for use with Series CV ISO/VDM cylinders. NGULR COMPNSTION To order, specify the model number. MODL NO. M6 M8 M0 M M6 M0 M6 x.0 M8 x.5 M0 x.5 M x.5 M6 x.5 M0 x.5 min.00 [5.].00 [5.].00 [5.]. [8.6].75 [.5].75 [.5] LTTR DIMNSION C min D min 0.65.875 [5.9] [7.6] 0.65.875 [5.9] [7.6].65.875 [5.9] [7.6].87 [9.0] [55.5].5. [8.5] [8.].5. [8.5] [8.] 0 [.7] 0 [.7].50 [.7].50 [.7].8 [0.6].8 [0.6] F 0.875 [.] 0.875 [.].875 [.].0 [5.].56 [9.7].56 [9.7] G 0.97 [5.0] 0.97 [5.0].97 [5.0].6 [6.0]. [8.0].9 [0.0] NOT: NUMRS IN [ ] R mm. IMPRIL QUIVLNTS R PROVIDD FOR CONVNINC. INTRNL THRD X DP G NFITS.0 [0.8] LTRL COMPNSTION Rod Couplers eliminate expensive precision machining for mounting fixed or rigid cylinder on guide or slide applications. Cylinder efficiency is increased by eliminating friction caused by misalignment. Couplers compensate for angular error and /" [0.8 mm] lateral misalignment on push and pull stroke. Couplers provide greater reliability and reduce cylinder and component wear, simplifying alignment problems in the field. Rod Couplers are manufactured from high tensile and hardened steel components. THRD F DI.0 [0.8] LTRL COMPNSTION NGULR COMPNSTION D C CT-0 (800) 6-85 www.phdinc.com/cv D-
MOUNTING CCSSORIS: SRIS CV CYLINDRS RCTNGULR FLNG MOUNTING SIZS 0 & 5 mm (MF8 PR ISO 6) UF TF ZF + STROK MF TG SQ D d HOL THRU UR OPTIONL M JM NUT X HOL THRU FOR F FSTNR MF Z + STROK SIZS -00 mm (MF/MF PR VDM 56) W OPTIONL X FD SHCS LTTR DIM/ TOLRNC d/h F/H FD TG MF TF/Js UF max UR max W/* CV Z max ZF CVC Z max ZF Kit No.** -Z Kit No.** SIZ 0 mm 5 mm in mm in mm 0.866.0 M6 x.0 M x 0.7 x 8.0 6.0 0.97 5.0.969 50.0.756 70.0.575 0.0 0.78 9.0.50.70 89.0 9.0.89 8.0.86 86.0 58-07- 58-07- 0.866.0 M6 x.0 M x 0.7 x 8.06 7.0 0.97 5.0.969 50.0.756 70.0.575 0.0 0.906.0.858.055 98.0 0.0.6 9.0.89 97.0 58-07- 58-07- NOTS: )* ±.055 in [±. mm] )** Kit includes flange and cylinder mounting hardware for one end only. UF TF TG SQ W MF ZF + STROK MF R X F HOL THRU d HOL THRU Z + STROK LTTR DIM/ TOLRNC d/h F/H TG max R/JS MF TF/JS UF max Fastener* W Z max ZF Kit No.* -Z Kit No.* SIZ mm 0 mm 50 mm 6 mm 80 mm in mm in mm in mm in mm in mm.8.76.80.969.60.9.50.86.60.88 5.8 M6 x x 0 0.0 7.0.5 50.0.0 0.0 6.0 86.0 6.0.0 0.0 58-0- 58-0-.78.5.96.8.7.9.85.780.787 5.59 5.709 5.0 9.0 8.0 58.0 6.0 0.0 7.0 96.0 M6 x x 0 0.0.0 5.0 58-0- 58-0- *Kit includes flange and cylinder mounting hardware for one end only..575.5.8.756.77.7.5.58.98 5.866 6.0 0.0 9.0 6.5 70.0 5.0.0 90.0 5.0 M8 x.5 x 0 58-0- 58-0- 5.0 9.0 55.0.77.5..6.969.7.97 5.8.98 6.96 6.69 5.0 9.0 56.5 85.0 50.0.0 00.0 0.0 M8 x.5 x 0 58-0- 58-0- 5.0 65.0 70.0.77.7.85..80.60.96 6.96.8 7.65 7.80 5.0.0 7.0 05.0 6.0 6.0 6.0 65.0 M0 x.5 x 5 58-05- 58-05- 0.0 8.0 90.0 00 mm in mm.65.55.50 5.8.95.60 5.906 7.6.78 7.795 8.07 55.0.0 89.0 0.0 75.0 6.0 50.0 87.0 M0 x.5 x 5 58-06- 58-06- 5.0 98.0 05.0 D- (800) 6-85 www.phdinc.com/cv CT-0
MOUNTING CCSSORIS: SRIS CV CYLINDRS S MOUNTING SIZS 0 & 5 mm (MS PR ISO 6) LTTR DIM/ TOLRNC /H O max U max NH/** S* TG TR/Js US max X* XU/^ Kit No.^^ -Z Kit No.^^ SIZ 0 mm 5 mm in mm in mm 0.60 0.5 0.787 0.98.898.0.575.65.055 0.57 587-07- 587-07- 6.6 8.0 0.0 5.0 99.0 6.0 0.0 55.0 0.0.0 0.60 0.5 0.787 0.98.09.06.575.65.09 0.5 587-07- 587-07- 6.6 8.0 0.0 5.0 0.0 7.0 0.0 55.0.0 8.0 NOTS: )* Dimensions shown are for CVC units. dd to S dimension.5 in [8 mm] for CV0 and.6 in [6 mm] for CV5. )** ±.008 in [± 0. mm] )^ ±.055 in [±. mm] )^^ Kit includes bracket and cylinder mounting hardware for one end only. XU X + STROK U S + STROK Kit can only be mounted in orientation shown. X DI PR ND O TG TR US NH D SIZS -00 mm (MS PR VDM 56) X + STROK TG SQ T H LTTR DIM/ TOLRNC /H TG max TR O max U/** H/JS5 T S X Fastener* Kit No.* -Z Kit No.* X DI PR ND U O S + STROK SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm.76.80.969.60..95.60.77 5.59 5.669 M6 x x 0 587-0- 587-0- 7.0.5 50.0.0.0.0.0.5.0.0.9.96.8.7.59.0.7.77 6.9 6.7 M6 x x 0 587-0- 587-0- 0.0 8.0 58.0 6.0 5.0 8.0 6.0.5 6.0 6.0 NOTS: )* Kit includes bracket and cylinder mounting fasteners for one end only. )** ±.008 in [±0. mm].9.8.756.77.59.60.77.7 6.69 6.890 0.0 6.5 70.0 5.0 5.0.0 5.0 5.5 70.0 75.0 M8 x.5 x 5 587-0- 587-0-.9..6.969.59.60.969.7 7.8 7.80 0.0 56.5 85.0 50.0 5.0.0 50.0 5.5 85.0 90.0 M8 x.5 x 5 587-0- 587-0- TR.7.85..80.787.6.80.56 8.68 8.65.0 7.0 05.0 6.0 0.0.0 6.0 6.5 0.0 5.0 M0 x.5 x 5 587-05- 587-05-.57.50 5.8.95.98.6.795.56 8.66 9.055.5 89.0 0.0 75.0 5.0.0 7.0 6.5 0.0 0.0 M0 x.5 x 5 587-06- 587-06- ll dimensions are reference only unless specifically toleranced. CT-0 (800) 6-85 www.phdinc.com/cv D-
MOUNTING CCSSORIS: SRIS CV CYLINDRS FSTNR MOUNTING SIZS 0 & 5 mm (MX) SIZS -00 mm (MX PR ISO 6) D ZT + STROK TG SQ DD THRD LTTR DIM 0 mm in mm 5 mm in mm SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm.669 7.0.669 7.0.906.0.906.0.0 8.0.0 8.0 M6 x.0 M6 x.0 M8 x.5 M8 x.5 M0 x.5 M0 x.5 5.9.80 7.0.5 5.98.96 5.0 8.0 6.55.8 66.0 6.5 7.6. 8.0 56.5 7.95.85 0.0 7.0 8.5.50 7.0 89.0 680-0- 680-0- 680-0- 680-0- 680-0- 680-0- 680-0- 680-0- 680-0- 680-0- 680-0- 680-0- min 0.5.0 0.5.0 DD M x 0.7 M x 0.7 ZT TG.780*.0 96.0* 6.0.*.06 05.0* 7.0 Kit No.** -Z Kit No.** 680-0- 680-0- 680-0- 680-0- NOTS: )* Dimensions shown are for CVC units. dd ZT dimension.5 in [8 mm] for CV0 and.6 in [6 mm] for CV5. )**Kit includes cylinder mounting hardware for one end only. RR FORK MOUNTING SIZS -00 mm (MP PR VDM 56) XD + STROK FL L SQ U C MR CD DI TG SQ LTTR DIM/ TOLRNC max max U/h C/H TG FL/* L min CD/H9 MR max XD Fastener** Kit No.** -Z Kit No.** SIZ mm 0 mm 50 mm 6 mm 80 mm 00 mm in mm in mm in mm in mm in mm in mm.559.969.77.0.80.866.7.9. 5.59 M6 x x 0 585-0- 585-0- 65.0 50.0 5.0 6.0.5.0.0 0.0.0.0.85.8.07.0.96.98.59.7.5 6.99 M6 x x 0 585-0- 585-0- 7.0 58.0 5.0 8.0 8.0 5.0 5.0.0.0 60.0.50.756.6.60.8.06.59.7.5 6.69 80.0 70.0 60.0.0 6.5 7.0 5.0.0.0 70.0 M8 x.5 x 0 585-0- 585-0- NOTS: ) * ±.008 in [±0. mm] tolerance ) ** Kit includes rear fork, cylinder mounting fasteners, pivot pin, and pivot pin retainer clips. ) Mounting is compatible with MP male hinge and MP pillow block..70.6.756.575..60.787.60.669 7.80 95.0 85.0 70.0 0.0 56.5.0 0.0 6.0 7.0 90.0 M8 x.5 x 0 585-0- 585-0-.58..5.969.85.7.787.60.669 8.68 5.0 05.0 90.0 50.0 7.0 6.0 0.0 6.0 7.0 0.0 M0 x.5 x 5 585-05- 585-05- 5.5 5.8..6.50.6.98.787.87 9.055 5.0 0.0 0.0 60.0 89.0.0 5.0 0.0.0 0.0 M0 x.5 x 5 585-06- 585-06- D- (800) 6-85 www.phdinc.com/cv CT-0