Tryton. Tool Services. People. Products. Performance. Calgary - Sales/Marketing Office 1100, 250 2nd St. SW Calgary, AB T2P 0C1 Ph:

Tool Services Lloydminster Field Office Corporate/Accounting Office 6702-56 Street Lloydminster, AB T9V 3A7 Ph: 780 875-0800 (24hr) Brooks Field Office 329-9th St. E Brooks, AB T1R OK2 Ph: 403 362-8600 (24hr) Calgary - Sales/Marketing Office 1100, 250 2nd St. SW Calgary, AB T2P 0C1 Ph: 403 263-6778 Drayton Valley Field Office 5622 56 St. Drayton Valley, AB T7A 0B2 Ph: 780 542-7070 Edmonton - Warehouse/Tech Services 1, 6404 Roper Rd. Edmonton, AB T6B 3P9 Ph: 780 468-0909 (24hr) Grande Prairie Field Office 110, 7001 98 St. Clairmont, AB T0H 0W0 Ph: 780 832-0011 (24hr) High Level Field Office 11961 95 St. High Level, AB T0H 1Z0 Ph: 780 926-2624 (24hr) Red Deer Field Office 1, 7836 49th Ave. Red Deer, AB T4P 2B5 Ph: 403 348-0062 (24hr) Slave Lake Field Office #301, Bay 1, Caribou Trail NW Slave Lake, AB T0G2A0 Ph: 780-849-2342 (24hr) Whitecourt Field Office 3421-41 Ave. Whitecourt, AB T7S 1N8 Ph: 780 706-2555 (24hr) Estevan, SK Field Office #7, Highway 39 East Estevan, SK S4A 0W3 Ph: 306 636-2291 www.trytontoolservices.com

Tool Services Table Of Contents Multi-Stage Frac Systems Retrievable Packers 1 2 3 Seal Bore Packers 4 Flow Control 5 Accessories 6 Service Tools 7 Plugs & Retainers 8 Tubing Anchors 9 Miscellaneous

OPEN HOLE REAMER The Tryton Open Hole Reamer is generally ran in order to dress out the open hole before installing Tryton Multi-Stage Frac Systems. The Reamer is a rigid heavy duty one-piece tool with 2 sets of 12 opposing tungsten carbide capped spiraled blades with an OD close to hole tolerances in order to best prepare the well bore ID properly before running tools. HEAVY DUTY ONE PIECE DESIGN 2 SETS OF 12 TUNGSTEN CARBIDE BLADES CLOSE OD TO OPEN HOLE TOLERANCE REAMER O.D. MIN TOOL I.D. THREAD CONNECTION in. mm in. mm in. mm 4.650 118.11 1.500 38.10 2 3/8 IF 60.3 5.750 146.05 2.000 50.80 3 1/2 IF 88.9 5.875 149.23 2.000 50.80 3 1/2 IF 88.9 5.950 151.13 2.000 50.80 3 1/2 IF 88.9 5.950 151.13 2.563 50.80 4 FH 101.6 6.125 155.58 2.000 50.80 3 1/2 IF 88.9 7.700 195.58 2.000 50.80 3 1/2 IF 88.9 Other sizes may be available upon request

OPEN HOLE CENTRALIZER The Tryton Open Hole Centralizer is mainly used with Tryton Open Hole Packers, generally as part of the Tryton Multi-Stage Frac System. The Centralizer helps to protect the packers from damage during equipment installation in the open hole section of the well bore as well as helping to centralize the packers during the setting procedure. The Centralizer freely swivels to allow for rotation when running in the hole if required and has spiralled grooves to ensure good circulation. AVAILABLE IN COMPOSITE OR STEEL HELPS PREVENT RUNNING DAMAGE CENTRALIZES WHEN SETTING SWIVELS TO ALLOW FOR TOOL STRING ROTATION MAX OH TOOL SIZE CENTRALIZER O.D. in. mm in. mm 4.500 114.30 4.625 117.48 5.500 139.70 5.56 141.22 5.750 146.05 5.812 147.63 5.875 149.23 5.930 150.62 7.375 187.33 7.435 188.85

RSB-1 LINER HANGER/PACKER The Tryton RSB-1 Liner Hanger/Packer is designed to be ran in applications where short to long liner tailpipe assemblies are required. All load bearing parts are designed to withstand large tension loads which makes it ideal for both vertical and horizontal applications whereby the liner system is to be anchored in place. The bi-directional slip system prevents both upward and downward movement after the tool is set. The RSB-1 does not rely on setting string weight or tension as it is set completely with differential hydraulic pressure. The RSB-1 has both an upper seal bore in order to maximize the ID through the connected tubing string. The RSB-1 is hydraulically set using the RSB Hydraulic Setting Tool and has a field adjustable shear release. DESIGNED FOR BOTH VERTICAL AND HORIZONTAL APPLICATIONS INCORPORATES A BI-DIRECTIONAL CARBIDE SLIP SYSTEM PREVENTS BOTH UPWARD AND DOWNWARD MOVEMENT FULL BORE ID INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE SHEAR RELEASE SETS WITH DIFFERENTIAL PRESSURE ONLY DESIGNED FOR HIGH TENSILE LOADS CASING SIZE CASING WEIGHT MAX TOOL O.D. MIN TOOL I.D. THREAD CONNECTION in. mm lbs/ft kg/m in. mm in. mm in. mm 7 177.8 29-32 43.15-47.62 5.875 149.23 3.875 98.42 4 1/2 LT&C 114.3 7 177.8 23-29 34.22-43.15 5.938 150.83 3.875 98.42 4 1/2 LT&C 114.3 7 177.8 17-23 25.30-34.22 6.188 157.18 3.875 98.42 4 1/2 LT&C 114.3

RSB HYDRAULIC SETTING TOOL The Tryton RSB Hydraulic Setting Tool was designed to set the RSB-1 Liner Hanger Packer either by itself or in conjunction with other equipment such as Tryton's horizontal Multi-Stage Frac system. In addition to the RSB-1 Liner Hanger Packer, the RSB Setting Tool can be customized to set any Seal Bore Packer When ran without a lower plugging device in the tailpipe a large internal by-pass allows fluid to enter the work string eliminating the need to fill the work string while running in the hole. If there is tailpipe assembly such as the Multi-Stage Frac system with some type of float shoe or other type of plugging device in place then it may be necessary to fill while running in the hole. Once on depth, field adjustable differential pressure is applied activating a hydraulic chamber stroking the RSB Setting Tool against the RSB-1 Liner Hanger Packer which engages the slips and energizes the elements. There is a secondary ball seat within the setting tool if required. Once the RSB-1 Liner Hanger Packer is set and tested the RSB setting tool is released with a combination of right hand rotation while holding tension. Ports between seals ensures drainage while tripping. LARGE INTERNAL BYPASS SECONDARY BALL SEAT SELF DRAINING WHEN PULLING OUT OF HOLE OPTIONAL SUPPLEMENTARY SETTING CHAMBERS FIELD ADJUSTABLE SETTING PRESSURE CAN BE CUSTOMIZED TO SET ANY SEAL BORE PACKER SETTING CHAMBER AREA BASE TOOL O.D. MAX TOOL I.D. THREAD CONNECTION Sq. In. Sq. cm in. mm in. mm in. mm 21.3 137.43 5.500 139.70 1.750 44.45 3 1/2 IF 88.9

RSB LATCH SEAL ASSEMBLY The Tryton RSB Latch Seal Assembly is designed to be used with either the RSB or the RSB-1 Packer. The RSB seal assembly incorporates heavy duty quadruple bonded seals and is ran on the tubing after the packer has been set. The latch mechanism engages automatically with set down weight and disengages with right hand rotation while pulling tension. PREVENTS BOTH UPWARD AND DOWNWARD MOVEMENT WHEN LATCHED HEAVY DUTY BONDED SEALS AVAILABLE WITH PREMIUM ELASTOMERS LARGE BORE ID AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS CASING SIZE SEAL BORE SIZE MAX TOOL O.D. MIN TOOL I.D. THREAD CONNECTION in. mm in. mm in. mm in. mm in. mm 7 177.8 4.00 101.60 5.00 127.00 3.00 76.20 3 1/2 EUE 88.9 7 177.8 4.75 120.65 5.88 149.35 3.88 98.55 4 1/2 LT&C 114.3

ISOPAC-I SINGLE ELEMENT PACKER The Tryton IsoPac-I is a lower cost single element alternative to the dual element IsoPac or IsoPac-II. The IsoPac-I is normally ran in conjunction with several open hole packers within the Tryton Multi-Stage Frac System in horizontal wells. However, it can be ran in vertical and cased wells if required. The IsoPac Packers are hydraulically set with an internal locking mechanism providing a positive and reliable long term set and the outer components are locked to prevent premature setting. The setting pressure can be field adjusted with readily accessible setting shear screws. SINGLE ACTION SETTING PISTON OUTER COMPONENTS LOCKED TO PREVENT PREMATURE SETTING INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE SETTING PRESSURE DESIGNED FOR CASED HOLE OR OPEN HOLE VERTICAL/HORIZONTAL APPLICATIONS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS AVAILABLE WITH PREMIUM ELASTOMERS OPEN HOLE SIZE MAX TOOL O.D. MIN TOOL I.D. THREAD CONNECTION in mm in. mm in. mm in. mm 6 1/8-6 1/4 155.6-158.8 5.750 146.05 3.90 99.06 4 1/2 LT&C 114.3

ISOPAC-II DUAL ELEMENT PACKER The Tryton IsoPac-II is a large bore dual element hydraulic set packer that is normally ran in conjunction with several open hole packers within the Tryton Multi-Stage Frac System in horizontal wells. However, it can be ran in vertical and cased wells if required. The IsoPac Packers are hydraulically set with an internal locking mechanism providing a positive and reliable long term set and the outer components are locked to prevent premature setting. The setting pressure can be field adjusted with readily accessible setting shear screws. SINGLE ACTION SETTING PISTON OUTER COMPONENTS LOCKED TO PREVENT PREMATURE SETTING INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE SETTING PRESSURE DESIGNED FOR CASED HOLE OR OPEN HOLE VERTICAL/HORIZONTAL APPLICATIONS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS AVAILABLE WITH PREMIUM ELASTOMERS OPEN HOLE SIZE MAX TOOL O.D. MIN TOOL I.D. THREAD CONNECTION in mm in. mm in. mm in. mm 6 1/8-6 1/4 155.6-158.8 5.750 146.05 3.90 99.06 4 1/2 LT&C 114.3

ANCHORPAC PACKER The Tryton AnchorPac Packer is designed to be run in either cased or open hole applications in vertical or horizontal wells. The AnchorPac can be ran as a single zone application packer or ran in conjunction with several packers in a multiple zone completion. The AnchorPac Packer incorporates a one piece bi-directional slip system in order to help prevent movement during higher pressure operations. Typically, on multiple zone horizontal open hole applications the AnchorPac would be used as the toe packer and/or the liner hanger packer. Durable construction and reliability makes the AnchorPac an excellent alternative to using inflatable packers. The AnchorPac is hydraulically set with an internal locking mechanism providing a positive and reliable long term set. The setting pressure can be field adjusted with readily accessible setting shear screws. The packer has a straight pull shear release which can also be readily adjusted in the field. SINGLE ACTION SETTING PISTON OUTER COMPONENTS LOCKED TO PREVENT PREMATURE SETTING ANCHORPAC INCORPORATES A BI-DIRECTIONAL SLIP SYSTEM INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE SETTING PRESSURE FIELD ADJUSTABLE SHEAR RELEASE DESIGNED FOR CASED HOLE OR OPEN HOLE VERTICAL/HORIZONTAL APPLICATIONS AVAILABLE WITH CARBIDE SLIPS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS AVAILABLE WITH PREMIUM ELASTOMERS OPEN HOLE SIZE MAX TOOL O.D. MAX TOOL I.D. THREAD CONNECTION in mm in. mm in. mm in. mm 5 7/8-6 1/16 149.2-154.0 5.500 139.70 3.53 89.66 4 1/2 LT&C 114.3 6 1/8-6 1/4 155.6-158.8 5.750 146.05 3.00 76.20 3 1/2 EUE 88.9 6 1/8-6 1/4 155.6-158.8 5.875 149.23 3.00 76.20 3 1/2 EUE 88.9 6 1/8-6 1/4 155.6-158.8 5.750 146.05 3.78 96.04 4 1/2 LT&C 114.3 6 1/8-6 1/4 155.6-158.8 5.875 149.23 4.00 101.60 4 1/2 LT&C 114.3

SWELLRIGHT PACKER The SwellRight Packer's standard swellable packer range is available as an oil or water swelling elastomer. This single element design uses a patent pending bonding process to provide high performance over short element lengths. SwellRight packers are available in wide range of sizes and utilize proprietary oil and water swell compounds. SIMPLE TO INSTALL STRONG AND DURABLE VERTICAL/HORIZONTAL APPLICATIONS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS OIL AND WATER ACTIVATION AVAILABLE BASE PIPE O.D. ELEMENT O.D. HOLE SIZE ELEMENT LENGTH in. mm in. mm in. mm ft m 2.375 60.3 3.500 88.9 4.000 101.6 3, 6 & 10 0.9, 1.8 & 3.0 2.875 73.0 4.000 101.6 4.750 120.7 3, 6 & 10 0.9, 1.8 & 3.0 3.500 88.9 5.750 146.1 6.125 155.6 3, 6 & 10 0.9, 1.8 & 3.0 4.000 101.6 5.625 142.9 6.000 152.4 3, 6 & 10 0.9, 1.8 & 3.0 4.000 101.6 5.750 146.1 6.125 155.6 3, 6 & 10 0.9, 1.8 & 3.0 4.500 114.3 5.625 142.9 6.000 152.4 3, 6 & 10 0.9, 1.8 & 3.0 4.500 114.3 5.750 146.1 6.125 155.6 3, 6 & 10 0.9, 1.8 & 3.0 4.500 114.3 5.875 149.2 6.250 158.8 3, 6 & 10 0.9, 1.8 & 3.0 5.500 139.7 8.150 207.0 8.500 215.9 3, 6 & 10 0.9, 1.8 & 3.0 6.625 168.3 8.150 207.0 8.500 215.9 3, 6 & 10 0.9, 1.8 & 3.0 7.000 177.8 8.150 207.0 8.500 215.9 3, 6 & 10 0.9, 1.8 & 3.0 7.000 177.8 9.150 232.4 9.500 241.3 3, 6 & 10 0.9, 1.8 & 3.0 7.625 193.7 9.150 232.4 9.500 241.3 3, 6 & 10 0.9, 1.8 & 3.0 9.625 244.5 11.500 292.1 12.250 311.2 3, 6 & 10 0.9, 1.8 & 3.0 13.375 339.7 16.500 419.1 17.500 444.5 3, 6 & 10 0.9, 1.8 & 3.0

FZR ON/OFF TOOL The Tryton FZR On/Off is an overshot type tubing disconnect/connect incorporating a J-slot that automatically engages on and disengages with a ¼ turn to the right at the tool. The FZR On/Off incorporates a proven and reliable quadruple bonded valve system which can be made out of various elastomeric materials as required. The FZR has a heavy duty 3 lug J-slot design to maximize the tensile loading capability and a full bore slick joint that allows for the largest possible ID available while maintaining a high pressure rating. A wireline profile can be cut in the slick joint if required. PROVEN BONDED SEAL SYSTEM RIGHT HAND RELEASE/LEFT HAND RELEASE 3 LUG J-SLOT DESIGN FOR HIGH TENSILE LOADING FULL BORE ID WIRELINE PROFILE CAN BE CUT IF REQUIRED AVAILABLE IN A WIDE RANGE OF MATERIALS & CONNECTIONS OPEN HOLE SIZE MAX TOOL O.D. MAX TOOL I.D. THREAD CONNECTION in. mm in. mm in. mm in. mm 6 1/8-6 1/4 155.57-158.75 5.875 149.23 3.00 76.20 3 1/2 EUE 88.9 6 1/8-6 1/4 155.57-158.75 5.875 149.23 3.94 100.03 4 1/2 LT&C 114.3 Common Sizes shown above, other sizes are available upon request Length and OD may vary if special threads are used

HYDROPORT FRAC SLEEVE The Tryton HydroPort frac sleeves are designed for use when selectively stimulating multiple zones in either open or cased hole applications. The HydroPort can be used in either horizontal or vertical wells and is usually the first valve ran in the well accompanied by multiple IsoPort frac sleeves. The HydroPort frac sleeve is hydraulically opened and an internal locking mechanism ensures the open position is securely maintained. The HydroPort frac sleeve is activated by field adjustable differential pressure from inside the sleeve across the actuation ports either by a plugging device below, usually being the ball seat circulating sub. Once open, the sleeves have an internal locking mechanism to ensure the open position is securely maintained. INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE OPENING PRESSURE FULL BORE ID SUITABLE FOR HIGH PRESSURE APPLICATIONS DESIGNED FOR BOTH HORIZONTAL AND VERTICAL APPLICATIONS DESIGNED FOR MULTIPLE ZONE APPLICATIONS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS MAX BODY O.D. MAX TOOL I.D. THREAD CONNECTION in. mm in. mm in. mm 4.281 108.74 2.38 60.30 2 7/8 EUE 73.0 5.000 127.00 3.31 84.10 4 1/2 LT&C 114.3 5.688 144.48 3.00 76.20 3 1/2 EUE 88.9 5.688 144.48 3.85 97.79 4 1/2 LT&C 114.3 6.820 173.23 4.85 123.19 5 1/2 LT&C 139.7

HYDROPORT-C FRAC SLEEVE The Tryton HydroPort-C frac sleeve is designed to be the toe sleeve on a cemented-in liner system either as part of Tryton s cemented-in ball drop system with the IsoPort-C frac sleeve or part of a plug and perf frac system. The HydroPort-C frac sleeve is activated by field adjustable differential pressure from inside the sleeve across the actuation ports and once open, the sleeve has an internal locking mechanism to ensure the open position is securely maintained. INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE OPENING PRESSURE LARGE BORE ID SUITABLE FOR HIGH PRESSURE APPLICATIONS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS MAX BODY O.D. MIN TOOL I.D. THREAD CONNECTION in. mm in. mm in. mm 5.700 144.78 3.56 90.42 4 1/2 LT&C 114.3 6.820 173.23 3.85 123.19 5 1/2 LT&C 139.7

ISOPORT FRAC SLEEVE The Tryton IsoPort frac sleeve is designed for selectively stimulating multiple zones in either open or cased hole applications. The IsoPort can be used in either vertical or horizontal wells usually in conjunction with the HydroPort frac sleeve and IsoPac/AnchorPac Packers. The IsoPort frac sleeve is activated by circulating a ball into a drillable seat inside the tool. Applied differential pressure from above the ball seat shifts the internal piston downward opening up the frac ports. The IsoPort has an internal locking mechanism keeping the piston locked securely into place after it has been shifted. The standard IsoPort piston is made out of a easily drillable material. INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE SETTING PRESSURE SUITABLE FOR HIGH PRESSURE APPLICATIONS DESIGNED FOR HORIZONTAL AND VERTICAL APPLICATIONS DESIGNED FOR MULTIPLE ZONE APPLICATIONS EASILY DRILLABLE BALL SEAT AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS CLOSABLE OPTION AVAILABLE MAX TOOL O.D. MAX TOOL I.D. THREAD CONNECTION in. mm in. mm in. (mm) 4.281 108.74 2.500 63.50 2 7/8 (73.0 mm) EUE 5.688 144.50 3.000 76.20 3 1/2 (88.9 mm) EUE 5.688 144.50 3.875 98.43 4 1/2 (114.3 mm) LT&C 6.690 169.93 5.000 127.00 5 1/2 (139.7 mm) LT&C

ISOPORT-C FRAC SLEEVE The Tryton IsoPort-C frac sleeve is designed for selectively stimulating multiple zones in a cemented-in liner system. The IsoPort-C is used in conjunction with the toe frac HydroPort-C sleeve and is activated by circulating a ball into a millable seat inside the tool. Applied differential pressure from above the ball seat shifts the internal piston downward opening up the frac ports. The IsoPort-C has an internal locking mechanism keeping the piston locked securely into place after it has been shifted. INTERNAL LOCKING MECHANISM SUITABLE FOR HIGH PRESSURE APPLICATIONS DESIGNED FOR MULTIPLE ZONE APPLICATIONS EASILY MILLABLE BALL SEAT AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS MAX TOOL O.D. MAX TOOL I.D. THREAD CONNECTION in. mm in. mm in. (mm) 5.688 144.50 4.000 101.60 4 1/2 (114.3 mm) LT&C 6.690 169.93 5.000 127.00 5 1/2 (139.7 mm) LT&C

PASSPORT FRAC SLEEVE The Tryton PassPort Frac Sleeve is a ball drop activated frac sleeve designed to work in conjunction with Tryton s IsoPort Frac Sleeve so that a single ball size opens two frac ports independently. When the first ball passes through the PassPort sleeve it activates an internal seat in order that the second ball of the same size will open the PassPort after the lower frac with the IsoPort bas been completed. Not only does the PassPort enable substantially more stages in certain applications, much higher pumping rates can be achieved. SINGLE BALL SIZE ENABLES 2 SLEEVES TO BE OPENED INDEPENDENTLY CAN DESIGN FOR UP TO 41 STAGES ADJUSTABLE OPENING PRESSURE SUITABLE FOR HIGHER PRESSURE APPLICATIONS DESIGNED FOR HORIZONTAL AND VERTICAL APPLICATIONS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS Ball Sizes Seat Sizes in. mm in. mm 1.486 37.74 1.436 36.47 1.566 39.78 1.516 38.51 1.646 41.81 1.596 40.54 1.726 43.84 1.676 42.57 1.823 46.30 1.756 44.60 1.920 48.77 1.853 47.07 2.017 51.23 1.950 49.53 2.127 54.03 2.047 51.99 2.237 56.82 2.157 54.79 2.347 59.61 2.267 57.58 2.457 62.41 2.377 60.38 2.577 65.46 2.487 63.17 2.700 68.58 2.607 66.22 2.830 71.88 2.737 69.52 2.969 75.41 2.867 72.82 3.125 79.38 3.000 76.20 3.281 83.34 3.156 80.16 3.437 87.30 3.312 84.12 3.593 9.126 3.468 88.09 3.750 95.25 3.624 92.05

MULTI-PORT FRAC SLEEVE Tryton's Multi-Port Frac Sleeve is a ball drop activated frac sleeve specially designed to generate multiple fracs at the same time in a wellbore by using a single ball to shift open multiple frac sleeves. The Multi-Port sleeves are installed either as part of an open hole packer liner system or can be cemented in with the liner. The system is designed so that one ball will shift open all sleeves in the same stage prior to landing in a fixed sleeve at the bottom of the stage. The ports can be sized accordingly to optimize the frac within the target zone. ONE BALL CAN OPEN UP TO 20 SLEEVES CAN BE RAN WITH OPEN HOLE PACKERS OR CEMENTED IN EASILY MILLABLE SEATS FRAC PORTS CAN BE DESIGNED ACCORDINGLY TO OPTIMIZE STIMULATION Ball Sizes Seat Sizes in. mm in. mm 2.127 54.03 2.047 51.99 2.237 56.82 2.157 54.79 2.347 59.61 2.267 57.58 2.457 62.41 2.377 60.38 2.577 65.46 2.487 63.17 2.700 68.58 2.607 66.22 2.830 71.88 2.737 69.52 2.969 75.41 2.867 72.82 3.125 79.38 3.000 76.20 3.281 83.34 3.156 80.16 3.437 87.30 3.312 84.12 3.593 9.126 3.468 88.09 3.750 95.25 3.624 92.05

GATEWAY ISO-PORT FRAC SLEEVE The Tryton Gateway Iso-Port Frac Sleeve has all the proven features of the conventional Tryton Iso-Port with the additional benefit of selective zone isolation. The Gateway is ran as part of the conventional Multi- Stage Frac systemand after the sleeve is opened utilizing ball drop technology, the piston can then be drilled out and the sleeve can be closed/opened using the activation tool on coil. INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE SETTING PRESSURE DESIGNED FOR MULTIPLE ZONE APPLICATIONS CAN BE CLOSED/OPENED WITH COIL RAN ACTIVATION TOOL MAX TOOL O.D. MIN TOOL I.D. THREAD CONNECTIONS in. mm in. mm in. mm 5.688 144.48 3.000 76.20 3 1/2 LT&C 88.9 5.688 144.48 3.781 96.04 4 1/2 LT&C 114.3 6.820 173.23 4.000 101.60 5 1/2 LT&C 139.7

BALL SEAT CIRCULATING SUB The Tryton Ball Seat Circulating Sub is designed to be a reliable closeable circulation port generally ran at the bottom of a tool string in either cased or open hole for vertical or horizontal well completions. Once the tool string is in place and the required circulation operation is complete a ball is circulated onto the seat, an adjustable pre-determined pressure is applied and an internal sleeve shifts downwards which closes the internal circulating ports. Once the sleeve has been shifted a positive locking mechanism ensures it is securely maintained in place. Standard ball sizes are 0.75" (19.05mm) and 1.00" (25.40mm) but can be customized if required. INTERNAL SECURE LOCKING MECHANISM ADJUSTABLE CLOSING PRESSURE DESIGNED FOR BOTH HORIZONTAL AND VERTICAL APPLICATIONS DESIGNED FOR BOTH CASED AND OPEN HOLE APPLICATIONS AVAILABLE IN A WIDE RANGE OF MATERIALS AND CONNECTIONS MAX TOOL O.D. THREAD CONNECTION in. mm in. mm 4.281 108.74 2 7/8 EUE 73.0 5.400 137.16 3 1/2 EUE 88.9 5.400 137.16 4 1/2 LT&C 114.3 6.500 165.10 5 1/2 LT&C 139.7

VIKING FRAC SLEEVE/ACTUATION TOOL The Tryton Viking Frac Sleeve is designed for selectively stimulating multiple zones in either vertical or horizontal wells. The Viking Frac Sleeve can either be ran in conjunction with Tryton open hole packers or be cemented in the well bore. As many sleeves as required can be ran and each sleeve opens independently utilizing the Tryton Viking Actuation Tool on coil tubing. Using the Viking system, the frac can be pumped down the ID of the coil or the coil annulus. The Tryton Viking Actuation Tool utilizes a continuous J-slot to activate the locator keys for positive locating and anchoring into each sleeve. Each sleeve is independently opened upon reaching a preset field adjustable differential pressure from inside the sleeve. After stimulation, the coil is picked up, opening the unloader valve, resetting the tool to the running position and moved up to the next sleeve. INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE OPENING PRESSURE CAN BE USED IN CONJUNCTION WITH OPEN HOLE PACKERS OR CEMENTED IN PLACE DESIGNED FOR MULTIPLE ZONE APPLICATIONS NO LIMIT ON THE NUMBER OF SLEEVES RAN FULL BORE ID ACTUATION TOOL UTILIZES SIMPLE DESIGN WITH HEAVY DUTY REINFORCED CUP FOR DURABILITY AND EFFICIENCY CAN BE PUMPED DOWN THE COIL ID OR COIL ANNULUS MAX BODY O.D. MAX FIN O.D. MIN TOOL ID THREAD CONNECTIONS in. mm in m in. mm in. mm. 5.750 146.05 6.00 152.40 3.95 97.79 4 1/2 LT&C 114.3 6.820 173.23 7.25 184.15 4.95 123.19 5 1/2 LT&C 139.7

TLT FRAC TOOL The TLT Frac Tool is designed for stimulating isolated zones within cased vertical or horizontal well bores utilizing coil tubing. Quicker running speeds can be achieved even when moving through fluid or live wells due to an innovative fluid bypass. When moving up-hole the valve shuts providing a closed system isolating the target zone and containing fluids/proppants from all previously stimulated lower zones. The top end of the TLT tool incorporates a coil tubing field adjustable shear release. The TLT can be used in conjunction with the Tryton FB/CFB HydroPorts or any other similar frac port type systems such as other types of frac sleeves, burst disks or perforations. STIMULATION OF MULTI-ZONE WELLBORES - NEW & RECOMPLETIONS FUNCTIONS IN VERTICAL, DEVIATED, OR HORIZONTAL WELLS CAN BE USED WITH A WIDE RANGE OF FRAC PORT SYSTEMS RAPID DEPLOYMENT THROUGH FLUID FILLED WELLBORES SINGLE CUP ASSEMBLY AVAILABLE LARGE BORE FIELD ADJUSTABLE COIL TUBING SHEAR RELEASE CASING SIZE CASING WEIGHT THIMBLE O.D. MIN I.D. THREAD CONNECTION in. mm lbs/ft kg/m in. mm in. mm in. mm 4 1/2 114.3 9.5-13.5 14.1-20.1 3.875 98.43 1.70 43.18 2 3/8 EUE 60.3 5 1/2 139.7 15.5-17.0 23.1-25.3 4.750 119.4 1.81 46.0 2 3/8 EUE 60.3 5 1/2 139.7 13.0-15.5 19.3-23.1 4.810 122.2 1.81 46.0 2 3/8 EUE 60.3

TGW CUP PACKER The Tryton TGW Cup Packer is available in a single or double cup design. The primary use is for isolating casing and tubing leaks. The packer cups can be installed in any direction allowing each assembly to hold pressure in both directions if required. AVAILABLE IN SINGLE OR DOUBLE ELEMENT DESIGN COMPACT & INEXPENSIVE MEANS OF ISOLATION WIRE REINFORCED CUPS FOR DURABILITY CASING SIZE THREAD CONNECTIONS CASING WEIGHT MAX O.D. MIN I.D. in. mm in. mm lbs/ft. kg/m in. mm in. mm 4 1/2 114.3 2 3/8 EUE 60.3 15.1-16.6 22.5-24.7 4.08 103.6 2.00 50.8 4 1/2 114.3 2 3/8 EUE 60.3 9.5-11.6 14.1-17.2 4.15 105.4 2.00 50.8 5 127.0 2 3/8 EUE 60.3 18.0-21.0 26.8-30.2 4.34 110.3 2.00 50.8 5 127.0 2 3/8 EUE 60.3 13.0-15.0 19.3-22.3 4.62 117.3 2.00 50.8 5 1/2 139.7 2 3/8 EUE 60.3 17.0-23.0 29.8-34.2 4.98 126.4 2.00 50.8 5 1/2 139.7 2 3/8 EUE 60.3 15.5-17.0 23.1-25.3 5.12 130.0 2.00 50.8 5 1/2 139.7 2 3/8 EUE 60.3 13.0-15.0 19.3-22.3 5.20 132.0 2.00 50.8 5 1/2 139.7 2 7/8 EUE 73.0 17.0-23.0 29.8-34.2 4.98 126.4 2.50 63.5 5 1/2 139.7 2 7/8 EUE 73.0 15.5-17.0 23.1-25.3 5.12 130.0 2.50 63.5 5 1/2 139.7 2 7/8 EUE 73.0 13.0-15.0 19.3-22.3 5.20 132.0 2.50 63.5 7 177.8 2 7/8 EUE 73.0 26.0-29.0 38.7-43.1 6.38 162.0 2.50 63.5 7 177.8 2 7/8 EUE 73.0 22.0-24.0 32.7-35.7 6.59 167.3 2.50 63.5 7 177.8 2 7/8 EUE 73.0 17.0-20.0 25.3-29.8 6.62 168.1 2.50 63.5 Common sizes above, other sizes may be available if required

TENSION PACKER The Tryton Tension Packer is a compact, economical, retrievable packer. Primarily used in water flood applications, this packer can also be used for production and/or lower-medium pressure treating operations. Since the packer is tension set, it is ideally suited for shallow wells where set-down weight is not available. Various configurations of the Tryton Tension Packer are available including an endless J-slot version as well as alternate shear options. SIMPLE LOW COST PACKER FOR FLUID INJECTION ENDLESS J-SLOT AVAILABLE ALTERNATIVE SHEAR RELEASE AVAILABLE CASING PACKER O.D. WEIGHT MIN. I.D. MAX I.D. MAX O.D. THREAD CONNECTION in. mm lbs/ft kg/m in. mm in. mm in. mm in. mm 4 1/2 114.3 9.5-13.5 14.17-20.13 3.920 99.57 4.090 103.89 3.771 95.78 2 3/8 EUE 60.3 5 127.0 15.0-18.0 22.37-26.84 4.276 108.61 4.408 111.96 4.125 104.78 2 3/8 EUE 60.3 5 127.0 11.5-15.0 17.15-22.37 4.408 111.96 4.560 115.82 4.250 107.95 2 3/8 EUE 60.3 5 1/2 139.7 20.0-23.0 29.83-34.30 4.670 118.62 4.788 121.62 4.500 114.30 2 3/8 EUE 60.3 5 1/2 139.7 15.5-20.0 23.11-29.83 4.778 121.36 4.950 125.73 4.641 117.88 2 3/8 EUE 60.3 5 1/2 139.7 13.0-17.0 19.39-25.35 4.892 124.26 5.044 128.12 4.750 120.65 2 3/8 EUE 60.3 5 1/2 139.7 13.0-15.5 19.39-23.11 4.950 125.73 5.044 128.12 4.781 121.44 2 3/8 EUE 60.3 7 177.8 38.0 56.67 5.830 148.08 5.921 150.39 5.656 143.66 2 7/8 EUE 73.0 7 177.8 32.0-35.0 47.72-52.20 6.044 153.52 6.094 154.79 5.812 147.62 2 7/8 EUE 73.0 7 177.8 26.0-29.0 38.78-43.25 6.184 157.07 6.276 159.41 5.968 151.59 2 7/8 EUE 73.0 7 177.8 20.0-26.0 29.83-38.78 6.276 159.41 6.456 163.98 6.078 154.38 2 7/8 EUE 73.0 7 177.8 17.0-20.0 25.35-29.83 6.456 163.98 6.538 166.07 6.266 159.16 2 7/8 EUE 73.0 Common sizes above, other sizes may be available if required

TS-3 SINGLE GRIP COMPRESSION PACKER The TS-3 Single Grip Packer is a single-grip, compression-set, retrievable mechanical production packer that is suitable for most production, stimulation and testing operations. The field proven large bore design allows unrestricted fluid flow and wireline operations through the tubing. The TS-3 also incorporates an internal bypass to prevent swabbing when running and retrieving. NORMALLY RH COMPRESSION SET, STRAIGHT PICK-UP RELEASE OPTIONAL J-SLOT CONFIGURATIONS LARGE BYPASS FOR RUNNING, RETRIEVING AND EQUALIZING AVAILABLE WITH BOTH LONG AND SHORT STROKE MANDRELS CASING SIZE CASING WEIGHT O.D. OF TOOL THREAD CONNECTIONS in. mm lbs/ft kg/m in. mm in. mm 4 1/2 114.3 15.1-16.6 22.3-24.6 3.594 91.29 2 3/8 EUE 60.3 4 1/2 114.3 9.5-13.5 14.1-20.1 3.750 95.25 2 3/8 EUE 60.3 5 127.0 18.0-20.8 26.82-13.9 4.000 101.60 2 3/8 EUE 60.3 5 127.0 11.5-15.0 17.1-22.3 4.125 104.78 2 3/8 EUE 60.3 5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 2 3/8 EUE 60.3 5 1/2 139.7 13.0-20.0 19.4-29.8 4.625 117.48 2 3/8 EUE 60.3 5 1/2 139.7 20.0-23.0 29.8-34.2 4.500 114.30 2 7/8 EUE 73.0 5 1/2 139.7 15.5-20.0 23.1-29.8 4.625 117.48 2 7/8 EUE 73.0 5 1/2 139.7 13.0-14.0 19.2-20.8 4.781 121.44 2 7/8 EUE 73.0 7 177.8 17.0-26.0 25.3-38.7 6.000 152.40 2 7/8 EUE 73.0 7 177.8 26.0-35.0 38.7-51.8 5.875 149.23 2 7/8 EUE 73.0

TS-4 DOUBLE GRIP COMPRESSION PACKER The Tryton TS-4 Double Grip Compression Set Packer is used for production, stimulation and testing. The mechanical upper hold down system reduces the cost and maintenance of a button type hydraulic hold down system. The TS-4 is equipped with a running bypass that reduces swabbing. Set down weight closes the bypass valve, sets the upper/lower slips and energizes the packing elements. The closed bypass valve activates the pressure balanced hold down system. Internal pressure from below the elements aids in holding the bypass valve closed and preventing upward movement of the tubing string. To set, run the tool to setting depth, pick up tubing and rotate to the right ¼ turn at the packer. Tubing weight is applied, which sets the lower slips, closes the bypass valve and expands the packing elements. To release, raise the tubing, which first opens the bypass valve, then releases the slips and packing elements. NORMALLY RIGHT HAND COMPRESSION SET, STRAIGHT PICK-UP RELEASE NO HYDRAULIC HOLD DOWN BUTTONS BUILT IN UNLOADER WASHES DEBRIS FROM WHEN RETRIEVING SEQUENTIAL RELEASE UPPER SLIP SYSTEM AVAILABLE IN AUTOMATIC AND MANUAL JAY CONFIGURATIONS CASING SIZE CASING WEIGHT THREAD CONNECTION MAX O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm 2 7/8 73.0 6.4-6.5 9.5-9.7 1.050 EUE 26.7 2.250 57.15 0.625 15.88 3 1/2 88.9 7.7-10.2 11.5-15.0 1.900 NUE 48.3 2.781 70.63 1.250 37.75 4 1/2 114.3 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 2.000 50.80 5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 2.000 50.80 5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 2.000 50.80 5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80 5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80 5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.375 60.30 5 1/2 139.7 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.375 60.30 7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50 7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50 Common sizes above, other sizes may be available if required

SNAPSET COMPRESSION SET ISOLATION PACKERS The Tryton Snapset Compression Set Isolation Packers are used in multi-zone completions. The Snapset Packers set in compression with a lower anchor style packer below. The collet in the lower end of the tool shifts at a pre-determined value to energize the packing elements and set the upper slips. To release, straight pick-up on the tubing string is required. The Snapset I has no slips, the Snapset II has a tension slip only and the Snapset III has a compression slip only. The application and operational requirements will determine which is the best Snapset to use. COMPENSATING PISTON HOLD DOWN SYSTEM RUNNING BYPASS/EQUALIZING SYSTEM KEYED FOR ROTATION THRU PACKER INTERNAL COLLET TO PREVENT PRE-SET SEQUENTIAL RELEASE SLIP SYSTEM CASING SIZE CASING WEIGHT THREAD CONNECTION MAX. O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm SNAPSET I 2 7/8 73.0 6.4-6.5 9.5-9.7 1.050 EUE 26.7 2.250 57.15 0.625 15.88 4 101.6 9.5-11.0 14.1-16.4 1.900 EUE 48.3 3.250 82.55 1.500 38.10 4 1/2 114.3 15.1-16.6 22.5-24.7 1.900 EUE 48.3 3.594 91.29 1.500 38.10 4 1/2 114.3 13.5-15.1 20.1-22.5 2 3/8 EUE 60.3 3.656 92.86 1.938 49.23 4 1/2 114.3 9.5-13.5 14.1-20.1 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23 5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 1.938 49.23 5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 49.23 5 1/2 139.7 13.0-14.0 19.3-20.8 2 3/8 EUE 60.3 4.812 122.22 2.000 50.80 5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80 5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80 5 1/2 139.7 13.0-14.0 19.3-20.8 2 7/8 EUE 73.0 4.812 122.22 2.375 60.30 5 1/2 139.7 13.0-15.5 19.3-23.1 2 7/8 EUE 73.0 4.781 121.44 2.375 60.30 5 1/2 139.7 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.375 60.30 5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.375 60.30 6 152.4 14.0-20.0 20.8-29.8 2 7/8 EUE 73.0 5.188 131.78 2.375 60.30 6 5/8 168.3 24.0-32.0 35.8-47.6 2 7/8 EUE 73.0 5.500 139.70 2.500 63.50 6 5/8 168.3 17.0-20.0 25.3-29.8 2 7/8 EUE 73.0 5.750 146.10 2.500 63.50 7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50 7 177.8 23.0-29.0 34.2-43.2 2 7/8 EUE 73.0 5.969 151.61 2.500 63.50 7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50 7 5/8 193.7 24.0-29.7 35.7-44.2 2 7/8 EUE 73.0 6.672 169.47 2.500 63.50 7 5/8 193.7 33.7-39.0 50.2-58.0 2 7/8 EUE 73.0 6.453 163.91 2.500 63.50 8 5/8 219.1 24.0-40.0 35.7-59.5 2 7/8 EUE 73.0 7.500 190.50 2.500 63.50 Common sizes above, other sizes may be available if required SNAPSET II SNAPSET III

THI HYDRAULIC ISOLATION PACKER The Tryton THI Hydraulic Isolation Packer is a hydraulic set, single string tandem packer used in multiple zone wells. The THI Hydraulic Isolation Packer is generally used as the lower/middle packer(s) in multiple zone applications. ECONOMICAL EASILY ADJUSTABLE SET AND RELEASE SHEAR SCREWS COMPACT DESIGN CAN BE USED IN OPEN HOLE CASING SIZE CASING WEIGHT TUBING SIZE MAX O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm 4 1/2 114.3 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 2.000 50.80 5 127.0 18.0-20.0 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 2.000 50.80 5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 2.000 50.80 5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80 5 1/2 139.7 13.0-20.0 19.3-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80 5 1/2 139.7 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.500 63.50 5 1/2 139.7 13.0-20.0 19.3-29.8 2 7/8 EUE 73.0 4.625 117.48 2.500 63.50 7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50 7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50

HYDRO-CT PACKER The Tryton Hydro-CT Packer can be ran either on jointed pipe utilizing a conventional rig or rigless application using coil tubing. The Hydro-CT can be ran alone or in tandem for testing, production, water shut-off or zonal isolation in either vertical or horizontal wells. The Hydro-CT is hydraulically set with an internal locking mechanism providing a positive and reliable long-term pack-off. Both durable construction and compact size makes the Hydro-CT Packer an excellent alternative to conventional hydraulic packers in shallower wells. The Hydro-CT is released by dropping a ball onto an internal seat then pressure above causes the releasing pins to shear and the packer to release. INTERNAL LOCKING MECHANISM FIELD ADJUSTABLE SETTING PRESSURE FIELD ADJUSTABLE SHEAR RELEASE RELEASING MECHANISM INDEPENDENT OF SETTING MECHANISM CAN BE RAN IN SINGLE OR MULTIPLE PACKER APPLICATIONS CAN BE USED IN CONJUNCTION WITH OTHER COMPLETION TOOLS SUITED FOR BOTH VERTICAL AND HORIZONTAL APPLICATIONS CASING SIZE CASING WEIGHT TUBING SIZE MAX O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm 4 1/2 114.3 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 2.000 50.80 Common sizes above, other sizes may be available if required

TI-1 INFLATABLE SINGLE SET PACKER The Tryton TI-1 Inflatable Single Set Packer is normally used in open hole for isolating zones or in casing whereby a restriction needs to be passed through and can be used for testing, treating, production or injection. The TI-1 is a hydraulically set single use packer that may be used in both vertical or horizontal wells. After the TI-1 is set an internal locking sleeve maintains inflation. The packer comes in both rotational or straight pull release. The TI-1 packer element incorporates high strength cable to provide good expansion characteristics in washed out or irregular well bores, as well as to provide high differential pressure capabilities. After the packer is released, the elements are designed to return very close to the original run-in diameter. The elements are less likely to lose rubber down hole because superior bonding occurs between the rubber and cable rather than just rubber alone. AVAILABLE IN TENSION OR ROTATIONAL RELEASE MODELS INTERNAL SLEEVE MAINTAINS INFLATION IN PACKER PRESSURE ACROSS ELEMENT IS FULLY EQUALIZED WHEN UNSETTING HEAVY DUTY CABLE RE-INFORCED ELEMENT DIFFERENT ELASTOMER COMPOUNDS AVAILABLE FOR HPHT AVAILABLE IN A VARIETY OF MATERIALS AND CONNECTIONS ELEMENT O.D. MIN. TOOL I.D. THREAD CONNECTIONS in. mm in. mm in. mm 3.12 79.25 0.750 20.07 2 3/8 EUE 60.3 3.62 91.95 1.750 44.45 2 3/8 EUE 60.3 4.25 107.95 1.938 49.23 2 7/8 EUE 73.0 5.50 139.70 1.938 63.50 2 7/8 EUE 73.0 Common sizes above, other sizes may be available if required

HYDRO-GRIP II HYDRAULIC SET PACKER The Tryton Hydro-Grip II hydraulic set packer is a compact 2 elemetn single string pressure activated double grip production packer, used in single or multi zone completions. The Hydro-GripII Packer is ideally suited for applications where it is desired to set the packer(s) after the well is flanged up or for multiple zone completions. The Hydro-Grip II Packer incorporates a pressure balance system which helps compensate for pressure differentials across the packer. The 2 element cup type system is a more compact packer in comparison to the Hydro-Grip III. RUNNING BYPASS RELEASE EQUALIZING SYSTEM PRESSURE BALANCED SYSTEM STRAIGHT PULL RELEASE FIELD ADJUSTABLE SETTING PRESSURE FIELD ADJUSTABLE RELEASING SHEAR CASING SIZE CASING WEIGHT THREAD CONNECTION MAX O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm 4 1/2 114.3 9.5-13.5 14.1-20.1 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23 5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80 5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80 7 177.8 26.0-35.0 38.7-52.1 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50 7 177.8 17.0-26.0 25.4-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50 Common sizes above, other sizes may be available if required

TI-2 INFLATABLE MULTI-SET PACKER The TI-2 Inflatable Multi-Set Packer is used for isolating zones in open-hole or in casing. The tool is re-settable and may be used for testing, treating, production, or stimulation of several zones with each trip into the well. The TI-2 incorporates a durable rugged design for reliable multiple sets in the same trip. The TI-2 Packer may be used in vertical, deviated or horizontal wells. No rotation is required to set the packer, however right-hand rotation is required to unset the packer. Once the TI-2 is released it can be moved and re-set by dropping a dart into a seat whereby the element can be re-inflated. The dart is then be pumped through to a catcher and the procedure can be repeated. CABLE REINFORCED ELEMENTS EXPOSED CABLE ELEMENT AVAILABLE FOR CASED HOLES RIGHT-HAND TURN RELEASE USES SEATS AND DARTS TO RE-SET DIFFERENT ELASTOMER COMPOUNDS AVAILABLE FOR HPHT AVAILABLE IN A VARIETY OF MATERIALS AND CONNECTIONS ELEMENT O.D. MIN. TOOL I.D. THREAD CONNECTIONS in. mm in. mm in. mm 4.25 107.95 1.562 39.67 2 3/8 EUE 60.3 5.50 139.70 1.562 39.67 2 7/8 EUE 73.0 Common sizes above, other sizes may be available if required

HYDRO-GRIP III HYDRAULIC SET PACKER The Tryton Hydro-Grip III hydraulic set packer is a 3 element single string pressure activated double grip production packer used in single or multi zone completions. The Hydro-Grip III Packer is ideally suited for applications where it is desired to set the packer(s) after the well is flanged up or for multiple zone completions. The Hydro-Grip III Packer incorporates a pressure balance system which helps compensate for pressure differentials across the packer. RUNNING BYPASS RELEASE EQUALIZING SYSTEM PRESSURE BALANCED SYSTEM STRAIGHT PULL RELEASE FIELD ADJUSTABLE SETTING PRESSURE FIELD ADJUSTABLE RELEASING SHEAR CASING SIZE CASING WEIGHT THREAD CONNECTION MAX O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm 4 1/2 114.3 9.5-13.5 14.2-20.0 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23 4 1/2 114.3 15.1 22.5 2 3/8 EUE 60.3 3.656 92.86 1.938 49.23 5 127.0 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 49.23 5 127.0 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 1.938 49.23 5 1/2 139.7 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 2.000 50.80 5 1/2 139.7 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 2.000 50.80 5 1/2 139.7 14.0-20.0 20.8-29.8 2 7/8 EUE 73.0 4.625 117.48 2.380 60.45 5 1/2 139.7 20.0-23.0 29.8-34.3 2 7/8 EUE 73.0 4.500 114.30 2.380 60.45 6 152.4 17.0-23.0 25.4-34.3 2 7/8 EUE 73.0 5.063 128.60 2.380 60.45 6 5/8 168.3 24.0-32.0 35.8-47.6 2 7/8 EUE 73.0 5.500 139.70 2.500 63.50 6 5/8 168.3 17.0-24.0 25.3-29.8 2 7/8 EUE 73.0 5.750 146.10 2.500 63.50 6 5/8 168.3 24.0-32.0 29.8-47.6 3 1/2 EUE 88.9 5.500 139.70 3.000 76.20 6 5/8 168.3 17.0-24.0 25.3-29.8 3 1/2 EUE 88.9 5.750 146.10 3.000 76.20 7 177.8 26.0-35.0 38.7-52.1 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50 7 177.8 23.0-29.0 34.3-43.2 2 7/8 EUE 73.0 5.940 152.40 2.500 63.50 7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50 7 177.8 26.0-32.0 38.7-47.6 3 1/2 EUE 88.9 5.875 149.23 3.000 76.20 7 177.8 17.0-29.0 25.3-38.7 3 1/2 EUE 88.9 6.000 152.40 3.000 76.20 7 5/8 193.7 24.0-29.7 35.7-44.2 2 7/8 EUE 73.0 6.672 169.47 2.500 63.50 7 5/8 193.7 33.7-39.0 50.2-58.0 2 7/8 EUE 73.0 6.453 163.91 2.500 63.50 7 5/8 193.7 24.0-29.7 35.7-44.2 3 1/2 EUE 88.9 6.672 169.47 3.000 76.20 7 5/8 193.7 33.7-39.0 50.2-58.0 3 1/2 EUE 88.9 6.453 163.91 3.000 76.20 8 5/8 219.0 32.0-40.0 47.7-59.7 4 1/2 EUE 114.3 7.500 190.50 4.000 101.60 9 5/8 244.5 32.3-43.5 48.2-64.9 4 1/2 EUE 114.3 8.500 215.90 4.000 101.60 9 5/8 244.5 43.5-53.5 64.9-79.8 4 1/2 EUE 114.3 8.250 209.55 4.000 101.60 Common sizes above, other sizes may be available if required

TD-2 DUAL STRING PRODUCTION PACKER The TD-2 Dual String Packer is a hydraulic set, mechanically held dual string production packer run above a single string hydraulic set or wireline set seal bore packer. Its short length makes it ideal for deviated wells or doglegs. Because no tubing manipulation is required to set this packer, the well head can be installed and flanged up before setting. It is available with short string or long string setting capabilities and a variety of tubing connections. It is also adaptable for submersible pump applications. The TD-2 features a sequential upper slip release system designed to release each slip individually reducing the pull required to release the packer. Due to the angles on the upper slips and upper slip cage, slips release smoothly from the casing. CASING LONG STRING CONNECTIONS SHORT STRING CONNECTIONS TOOL O.D. SIZE WEIGHT BOX UP/PIN DOWN MANDREL I.D. BOX UP/PIN DOWN MANDREL I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm in. mm in. mm 5 1/2 139.7 14.0-20.0 20.88-29.83 4.63 117.6 1.900 EUE 48.26 1.61 40.89 1.660 EUE 42.16 1.38 35.05 7 177.8 17.0-26.0 25.35-38.78 6.03 153.1 2 3/8 EUE 60.33 1.94 49.28 2 3/8 EUE 60.33 1.94 49.28 7 177.8 17.0-26.0 25.35-38.78 6.03 153.1 2 7/8 EUE 73.03 2.44 61.98 1.900 EUE 48.26 1.61 40.89 7 177.8 26.0-32.0 38.78-47.72 5.94 150.8 2 3/8 EUE 60.33 1.94 49.28 2 3/8 EUE 60.33 1.94 49.28 7 177.8 26.0-32.0 38.78-47.72 5.94 150.8 2 7/8 EUE 73.03 2.44 61.98 1.900 EUE 48.26 1.61 40.89 7 177.8 29.0-35-0 43.25-52.20 5.88 149.2 2 3/8 EUE 60.33 1.94 49.28 2 3/8 EUE 60.33 1.94 49.28 8 5/8 219.1 24.0-32.0 35.80-47.72 7.69 195.3 2 7/8 EUE 73.03 2.44 61.98 2 7/8 EUE 73.03 2.44 61.98 8 5/8 219.1 24.0-32.0 35.80-47.72 7.69 195.3 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28 8 5/8 219.1 36.0-40.0 53.69-59.65 7.44 189.0 2 7/8 EUE 73.03 2.44 61.98 2 3/8 EUE 60.33 1.94 49.28 9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 1.900 EUE 48.26 1.61 40.89 9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28 9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 2 7/8 EUE 73.03 2.44 61.98 9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 3 1/2 EUE 88.90 2.99 75.95 3 1/2 EUE 88.90 2.99 75.95 9 5/8 244.5 32.3-40.0 48.17-59.65 8.62 218.8 4 1/2 EUE 114.30 3.96 100.59 1.900 EUE 48.26 1.61 40.89 9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28 9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 3 1/2 EUE 88.90 2.99 75.95 2 7/8 EUE 73.03 2.44 61.98 9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 3 1/2 EUE 88.90 2.99 75.95 3 1/2 EUE 88.90 2.99 75.95 9 5/8 244.5 36.0-43.5 53.69-64.88 8.50 215.9 4 1/2 EUE 114.30 3.96 100.59 1.900 EUE 48.26 1.61 40.89 9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 1.900 EUE 48.26 1.61 40.89 9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 2 3/8 EUE 60.33 1.94 49.28 9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 2 7/8 EUE 73.03 2.44 61.98 9 5/8 244.5 47.0-53.5 70.09-79.79 8.31 211.1 3 1/2 EUE 88.90 2.99 75.95 3 1/2 EUE 88.90 2.99 75.95

TX-6/TX-6W DOUBLE GRIP RETRIEVABLE PACKER The Tryton TX-6/TX-6W are lower pressure single string double grip retrievable production packers that hold pressure from above and below. Once set, the TX-6/TX- 6W can be left in tension, compression or neutral. Incorporated into the design is an internal bypass system that along with fluid by pass while running, equalizes pressure before the upper slips are pulled from the casing wall. The TX-6/TX-6W Packers are designed for production, testing, zone isolation and injection applications. The TX-6 sets with a 1/4 right hand turn at the packer and releases with a 1/4 right hand turn, then straight pick up. The TX-6W sets on wireline and releases with a 1/4 right hand turn at the packer then straight pick-up. The TX-6 can be re-set multiple times whereby once the TX-6W is released it cannot be re-set in the standard configuration. TUBING, WIRELINE OR HYDRAULIC SET ON TUBING CAN BE PACKED -OFF WITH EITHER TENSION OR COMPRESSION QUARTER TURN TO RIGHT TO SET AND RELEASE OPTIONAL LH J-SLOT AVAILABLE COMPATIBLE WITH A WIDE VARIETY OF TRYTON PACKER ACCESSORIES CASING SIZE CASING WEIGHT TUBING SIZE MAX O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm 4 1/2 114.3 9.5-13.5 14.1-20.1 2 3/8 EUE 60.3 3.750 95.25 1.938 50.80 WIRELINE SET TUBING SET MODE 5 1/2 139.7 14.0-20.0 19.2-29.8 2 3/8 EUE 60.3 4.625 117.44 1.938 50.80 5 1/2 139.7 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.500 63.50 7 177.8 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50 7 177.8 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50 7 177.8 17.0-23.0 25.3-38.7 2 7/8 EUE 73.0 6.250 158.75 2.500 63.50 7 177.8 26.0-32.0 38.7-47.6 3 1/2 EUE 88.9 5.875 149.23 3.000 76.20 7 177.8 17.0-26.0 25.3-36.1 3 1/2 EUE 88.9 6.000 152.40 3.000 76.20 7 177.8 17.0-23.0 25.3-38.7 3 1/2 EUE 88.9 6.250 158.75 3.000 76.20 9 5/8 244.5 32.3-43.5 48.1-64.7 3 1/2 EUE 88.9 8.500 215.90 3.000 76.20 9 5/8 244.5 40.0-53.5 59.5-79.6 3 1/2 EUE 88.9 8.250 209.55 3.000 76.20 11 3/4 298.5 42.0-64.9 62.6-96.6 4 1/2 EUE 114.3 10.500 265.13 4.000 101.60 Common sizes above, other sizes may be available if required

TX-8/TX-8W DOUBLE GRIP RETRIEVABLE PACKER The Tryton TX-8/TX-8W packers are medium pressure single string double grip retrievable production packers that are capable of being set in tension or compression. Once set, the tubing string can be left in tension, compression or neutral. Incorporated into the design is an internal bypass system that along with fluid bypass while running, equalizes pressure before the upper slips are pulled from the casing wall. The Packers are designed for stimulation, service operations, production, testing, zone isolation and injection applications. The TX-8 sets and releases with a 1/4 right hand turn at the packer, then straight pick up. The TX-8W sets on wireline and releases with a 1/4 right hand turn at the packer then straight pick-up. The TX-8 can be re-set multiple times whereby once the TX-8W is released it cannot be re-set in the standard configuration. TUBING, WIRELINE OR HYDRAULIC SET ON TUBING CAN BE PACKED-OFF WITH EITHER TENSION OR COMPRESSION OPEN J-SLOT DESIGN 1/4 RIGHT HAND TURN TO SET AND RELEASE OPTIONAL LH J-SLOT AVAILABLE SEQUENTIAL RELEASE UPPER SLIP SYSTEM COMPATIBLE WITH A WIDE VARIETY OF PACKER ACCESSORIES SOUR SERVICE VERSION AVAILABLE AVAILABLE WITH PREMIUM ELASTOMERS TUBING SET WIRELINE SET

TX-8/TX-8W DOUBLE GRIP RETRIEVABLE PACKER CASING SIZE CASING WEIGHT THREAD CONNECTION MAX O.D. MIN I.D. in. mm lbs/ft kg/m in. mm in. mm in. mm 2 7/8 73.0 6.4-6.5 9.5-9.7 1.050 26.7 2.250 57.15 0.625 15.88 3 1/2 88.9 9.2-10.2 13.7-15.2 1.900 NU 48.3 2.781 70.6 1.250 31.75 4 101.6 10.4-12.9 15.5-19.2 1.900 EUE 48.3 3.187 80.95 1.500 38.10 4 101.60 9.5-11.0 14.1-16.4 1.900 EUE 48.3 3.250 82.55 1.500 38.10 4 1/2 114.30 9.5-13.5 14.1-20.9 2 3/8 EUE 60.3 3.750 95.25 1.938 49.23 4 1/2 114.30 13.5-15.1 20.1-22.5 2 3/8 EUE 60.3 3.656 92.86 1.938 50.80 4 1/2 114.30 15.1-20.0 22.5-29.8 2 3/8 EUE 60.3 3.500 88.90 1.703 43.26 5 127.00 11.5-15.0 17.1-22.3 2 3/8 EUE 60.3 4.125 104.78 1.938 49.23 5 127.00 18.0-20.8 26.8-31.0 2 3/8 EUE 60.3 4.000 101.60 1.938 49.23 5 1/2 139.70 14.0-20.0 20.8-29.8 2 3/8 EUE 60.3 4.625 117.48 1.938 49.23 5 1/2 139.70 20.0-23.0 29.8-34.2 2 3/8 EUE 60.3 4.500 114.30 1.938 49.23 5 1/2 139.70 13.0-14.0 19.2-23.1 2 7/8 EUE 73.0 4.781 121.44 2.375 60.30 5 1/2 139.70 15.5-20.0 23.1-29.8 2 7/8 EUE 73.0 4.625 117.48 2.375 60.30 5 1/2 139.70 20.0-23.0 29.8-34.2 2 7/8 EUE 73.0 4.500 114.30 2.375 60.30 6 5/8 168.28 24.0-32.0 35.8-47.6 2 7/8 EUE 73.0 5.500 139.70 2.500 63.50 6 5/8 168.28 17.0-24.0 25.3-35.7 2 7/8 EUE 73.0 5.750 146.10 2.500 63.50 7 177.80 17.0-26.0 25.3-38.7 2 7/8 EUE 73.0 6.000 152.40 2.500 63.50 7 177.80 23.0-29.0 34.2-43.2 2 7/8 EUE 73.0 5.969 151.61 2.500 63.50 7 177.80 26.0-32.0 38.7-47.6 2 7/8 EUE 73.0 5.875 149.23 2.500 63.50 7 177.80 17.0-26.0 25.3-38.7 3 1/2 EUE 88.9 6.000 152.40 3.000 76.20 7 177.80 26.0-32.0 38.7-47.6 3 1/2 EUE 88.9 5.875 149.23 3.000 76.20 7 5/8 193.68 29.7-33.7 44.2-50.1 2 7/8 EUE 73.0 6.625 169.47 2.500 63.50 7 5/8 193.68 33.7-39.0 49.1-58.0 2 7/8 EUE 73.0 6.453 163.91 2.500 63.50 8 5/8 219.08 24.0-40.0 35.7-59.5 4 1/2 EUE 114.3 7.750 190.50 4.000 101.60 8 5/8 219.08 20.0-28.0 29.8-59.5 4 1/2 EUE 114.3 7.500 190.50 4.000 101.60 9 5/8 244.48 32.3-43.5 48.2-64.9 4 1/2 EUE 114.3 8.500 215.90 4.000 101.60 9 5/8 244.48 43.5-53.5 64.9-79.8 4 1/2 EUE 114.3 8.250 209.55 4.000 101.60 10 3/4 273.05 32.8-51.0 48.9-76.1 4 1/2 EUE 114.3 9.625 244.48 4.000 101.60 10 3/4 273.05 51.0-65.7 76.1-98.0 4 1/2 EUE 114.3 9.312 236.52 4.000 101.60 11 3/4 298.45 42.0-65.0 62.6-97.0 4 1/2 EUE 114.3 10.438 265.13 4.000 101.60 13 3/8 339.73 54.5-77.0 81.3-114.8 4 1/2 EUE 114.3 12.000 304.80 4.000 101.60 Common sizes above, other sizes may be available if required