MDS Dead-front Padmount Switchgear Style Guide 1VAM224804-SG May 2010 Revision D The MDS style guide aids in the proper selection of your style number. When ordering the MDS, the style number must be given to the factory. Typical Style Code M D S 1 0 9 A N N N N M S S S S 0 0 Digit 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 Digit 17 and 18 are to be assigned by the factory Table 1. Unit Configuration Digits 1-6 Line Diagram Dimension Weight W (in) D (in) H (in) (lbs) MDS103 39.5 73 45 988 MDS104 39.5 73 45 950 MDS105 39.5 73 45 1016
Digits 1-6 Line Diagram Dimension Weight W (in) D (in) H (in) (lbs) MDS106 75 73 45 1263 MDS107 75 73 45 1263 MDS108 75 73 45 1273 MDS109 75 73 45 1406 MDS110 75 73 45 1406 MDS111 75 73 45 1406 MDS113 75 73 45 1406
Digits 1-6 Line Diagram Dimension Weight W (in) D (in) H (in) (lbs) MDS203 44 82 51 988 MDS204 44 82 51 988 MDS205 44 82 51 1273 MDS206 84 82 51 1577 MDS207 84 82 51 1577 MDS208 84 82 51 1591 MDS209 84 82 51 1710
Digits 1-6 Line Diagram Dimension Weight W (in) D (in) H (in) (lbs) MDS210 84 82 51 1710 MDS211 84 82 51 1710 MDS213 84 82 51 1710 Table 2. Fuse Compartment Options Digit 7 Fuse Type Mounting Only 15 and N None Padmount with no fuse compartment A SMU-20/DBU17 Fuse mounting for S&C SMU-20/Cutler-Hammer DBU17 fuses B SM-4 Fuse mounting for S&C SM-4 fuses C NX Fuse mounting for Cooper type NX clip style fuses Z Customer Specified Other customer specified fusing Mounting and End Fittings/Holders J SMU-20 Fuse mounting for S&C SMU-20 fuses including S&C 3097 end fittings K DBU17 Fuse mounting for Cutler-Hammer DBU17 fuses including Cutler- Hammer DBU-EFID end fittings L SM-4 Fuse mounting for S&C SM-4 fuses including 86632R2 fuse holders Z Customer Specified Other customer specified fusing J SMU-20 Fuse mounting for S&C SMU-20 fuses including S&C 3097 end fittings K DBU27 Fuse mounting for Cutler-Hammer DBU27 fuses including Cutler- Hammer DBU-EFID end fittings L SM-4 Fuse mounting for S&C SM-4 fuses including 86633R2 fuse holders Z Customer Specified Other customer specified fusing - Please see Table.15 for fuses (every fuse compartment will require 3 fuses)
Table 3. Fault Indicator Mounting Provision Digit 8 Provision N None No fault indicating provisions provided (standard) F Fault indicator provision w/ viewing window Provisions for mounting fault indicator with viewing window in each switch compartment door Z Customer Specified Other customer specified fault indicator mounting provision Table 4. Key Interlock Digit 9 Notes N No interlocks provided (standard) 1 Key interlocks to prevent paralleling of switches in compartments 1 & 2 Only available on 106, 109, 110, 111, 113, 206, 209, 210, 211, 213 3 Key interlocks to prevent opening fuse termination compartment doors unless all switches are locked open Only available on 105, 106, 107, 109, 111, 205, 206, 207, 209, 211 4 Key interlocks, combines functions of options 1 & 3 Only available on 106, 109, 111, 206, 209, 211 Table 5. Termination Depth Digit 10 N Standard 1 5" deeper termination compartment - one side 2 5" deeper termination compartment - both sides N Standard 1 5" deeper termination compartment - one side 2 5" deeper termination compartment - both sides Table 6. Provisions for storing Fuse Assemblies (fuse + end fittings) Digit 11 N None (Pocket for storing individual fuses without the end fittings is standard) 1 Provision in one compartment 2 Provision in two compartments Table 7. Enclosure Type Digit 12 Material M Mild steel Mild steel enclosure S Stainless Steel Stainless steel enclosure A Aluminum Marine grade aluminum enclosure M Mild steel Mild steel enclosure S Stainless Steel Stainless steel enclosure A Aluminum Marine grade aluminum enclosure
Table 8. Termination Height Digit 13 Height (in) Mild Steel S STD Low profile enclosure for installation on vaults or ground sleeves (Standard termination height) 1 6 Adaptor providing 6 inches of additional height (allows installation on smaller live-front pads) Stainless Steel S STD Low profile enclosure for installation on vaults or ground sleeves (Standard termination height) 1 6 Adaptor providing 6 inches of additional height (allows installation on smaller live-front pads) Aluminum S STD Low profile enclosure for installation on vaults or ground sleeves (Standard termination height) 1 6 Adaptor providing 6 inches of additional height (allows installation on smaller live-front pads) Digit 13 Height (in) Mild Steel S STD Low profile enclosure for installation on vaults or ground sleeves (Standard termination height) 1 6 Adaptor providing 6 inches of additional height (allows installation on smaller live-front pads) Stainless Steel S STD 1 6 Adaptor providing 6 inches of additional height Aluminum S STD 1 6 Adaptor providing 6 inches of additional height Table 9. Paint Digit 14 Color Specification S Green Guardian Green Munsell 7GY3.29/1.5 (standard) G* Grey ANSI-70 Gray T* Tan Tan Munsell 10YR6.0/3.0 Z* Special Paint Color Other Color *Must be ordered in quantities of 3 or more Table 10. Bushings Digit 15 S 600 amp bushings (switch/termination compartments) 2 200 amp bushing wells (switch/termination compartments)* Z Customer specified bushings * 3 bushing inserts are required for every switch compartment if option 2 is selected. Please see Table.14 for bushing inserts
Table 11. Bus Material Digit 16 S C Aluminum bus (standard) Copper bus Style Code Digit 17-18 Style Code Digit 17-18 to be left blank, they will be assigned by the factory Table 13. Accessories Part Number Accessory 80082000 Caution Label* Label Caution-High Voltage-Keep Out (Outside Doors) 80082052 Mr. Ouch Label* Label Warning-Hazardous Voltage-NEMA Mr. Ouch 80082053 Bilingual Mr. Ouch Warning Label* Label Warning-Hazardous Voltage-NEMA Mr. Ouch (Bilingual) 80082051 Bilingual Mr. Ouch Danger Label Label Danger-Hazardous Voltage-NEMA Mr. Ouch (Bilingual) Customer Label* Label Customer Specified 60061375 Ground lugs Ground lugs (2/0) (each) 33050191 Clamping bracket Hold down brackets (each) Additional venting Additional venting (Louvers on side panels) Hex head bolt Hex head locking (security) bolt *Standard labels are included with every unit the labels listed above are for any extra or special labeling. Table 14. Bushing Inserts Part Number 61050095 15kV Bushing Inserts 61050100 25kV Bushing Inserts - Every fuse compartment will require 3 bushing inserts - Every switch compartment with 200Amp bushing wells will require 3 bushing inserts Table 15. Fuses Amp Rating Cutler-Hammer DBU17 E-SPEED S&C SMU-20 E-SPEED 15kV 25kV 15kV 25kV 5A 62110001C 62112000C 62110001 62112000 7A 62110002C 62112001C 62110002 62112001 10A 62110003C 62112002C 62110003 62112002 13A 62110004C 62112003C 62110004 62112003 15A 62110005C 62112004C 62110005 62112004 20A 62110006C 62112005C 62110006 62112005 25A 62110007C 62112006C 62110007 62112006 30A 62110008C 62112007C 62110008 62112007 40A 62110009C 62112008C 62110009 62112008 50A 62110010C 62112009C 62110010 62112009 65A 62110011C 62112010C 62110011 62112010 80A 62110012C 62112011C 62110012 62112011 100A 62110013C 62112012C 62110013 62112012 125A 62110014C 62112013C 62110014 62112013 150A 62110015C 62112014C 62110015 62112014 175A 62110016C 62112015C 62110016 62112015 200A 62110017C 62112016C 62110017 62112016
Amp Rating Cutler-Hammer DBU17 K-SPEED S&C SMU-20 K-SPEED 15kV 25kV 15kV 25kV 3A 62110020C 6112020C 62110020 6112020 6A 62110021C 6112021C 62110021 6112021 8A 62110022C 6112022C 62110022 6112022 10A 62110023C 6112023C 62110023 6112023 12A 62110024C 6112024C 62110024 6112024 15A 62110025C 6112025C 62110025 6112025 20A 62110026C 6112026C 62110026 6112026 25A 62110027C 6112027C 62110027 6112027 30A 62110028C 6112028C 62110028 6112028 40A 62110029C 6112029C 62110029 6112029 50A 62110030C 6112030C 62110030 6112030 65A 62110031C 6112031C 62110031 6112031 80A 62110032C 6112032C 62110032 6112032 100A 62110033C 6112033C 62110033 6112033 140A 62110034C 6112034C 62110034 6112034 200A 62110035C 6112035C 62110035 6112035 Amp Rating Cutler-Hammer NX E-SPEED S&C SM-4 E-SPEED 15kV 25kV 15kV 25kV 3A 62110060C 62112060C 62110060 62112060 5A 62110061C 62112061C 62110061 62112061 7A 62110062C 62112062C 62110062 62112062 10A 62110063C 62112063C 62110063 62112063 13A 62110064C 62112064C 62110064 62112064 15A 62110065C 62112065C 62110065 62112065 20A 62110066C 62112066C 62110066 62112066 25A 62110067C 62112067C 62110067 62112067 30A 62110068C 62112068C 62110068 62112068 40A 62110069C 62112069C 62110069 62112069 50A 62110070C 62112070C 62110070 62112070 65A 62110071C 62112071C 62110071 62112071 80A 62110072C 62112072C 62110072 62112072 100A 62110073C 62112073C 62110073 62112073 125A 62110074C 62112074C 62110074 62112074 150A 62110075C 62112075C 62110075 62112075 175A 62110076C 62112076C 62110076 62112076 200A 62110077C 62112077C 62110077 62112077 Amp Rating Cutler-Hammer NX SLOW-SPEED S&C SM-4 SLOW-SPEED 15kV 25kV 15kV 25kV 15A 62110080C 62112080C 62110080 62112080 20A 62110081C 62112081C 62110081 62112081 25A 62110082C 62112082C 62110082 62112082 30A 62110083C 62112083C 62110083 62112083 40A 62110084C 62112084C 62110084 62112084 50A 62110085C 62112085C 62110085 62112085 65A 62110086C 62112086C 62110086 62112086 80A 62110087C 62112087C 62110087 62112087 100A 62110088C 62112088C 62110088 62112088 125A 62110089C 62112089C 62110089 62112089 150A 62110090C 62112090C 62110090 62112090 175A 62110091C 62112091C 62110091 62112091 200A 62110092C 62112092C 62110092 62112092
ABB Inc. 655 Century Point Lake Mary, FL 32746 Tel + 1 407-732-2000 or 1-800-929-7947 Fax +1 407-732-2029 www.abb.com/padmountswitch 1VAM224804-SG Rev. D May 2010 Copyright 2005 ABB. All rights reserved.